FS15 Series - SAi Hydraulic Motorssaihyd.com/old/fs/FS15.pdf · FS 15 Series 75 100 150 170 200 220...
Transcript of FS15 Series - SAi Hydraulic Motorssaihyd.com/old/fs/FS15.pdf · FS 15 Series 75 100 150 170 200 220...
Hydraulics, Inc.
FS 15 Series 75 100 150 170 200 220 250Displacement in3/rev 4.53 7.07 9.24 10.20 11.70 13.31 14.44Torque lb.ft/100 psi 6.01 9.33 12.26 13.53 15.52 17.66 19.16Nominal pressure 1) psi 4000 4000 4000 4000 4000 4000 4000Peak pressure 1) psi 5500 5500 5500 5500 5500 5500 5500 Max. speed 2) rpm 1000 1000 900 800 700 500 500Peak power HP 60 60 60 60 60 60 60
Max. casing pressure: 14.5 psi cont. (72.5 peak)Approximate weight: 53 lbs Motor casing oil capacity: .21 gal
1) Continuous or peak working pressure should be chosen on the required bearing lifetime, 2) Speed limitation with optional low speed distributors (eg. D31); cont. 250 rpm, max 500 rpm (see distributor pages section)
FS15 Series
FS15 Series HD 75 90 115 150 170 200 220 250Displacement in3/rev 4.60 5.52 7.05 9.20 10.20 11.70 13.31 14.44Torque lb.ft/100 psi 5.8 6.7 9.2 12 13.4 15.2 17.2 18.7Nominal Pressure 1) psi 4000 4000 4000 4000 4000 4000 4000 4000Peak pressure 1) psi 6525 6525 6000 6000 5800 5800 5800 5800Max. speed 2) rpm 1500 1350 1200 1100 1000 900 800 700Peak power HP 70 70 70 70 70 70 70 70
DIMENSIONSMETRIC VERSION
MOTOR END VIEW
SHAFT OPTIONSSTANDARD
7: Splined DIN 54801: Splined UNI 221
9: Splined DIN 54803: Splined UNI 221
8: Parallel Keyed 040
Spline DIN 5480 7 UNI 221 1
Parallel Keyed 8Internal Spline DIN 5480 9 UNI 221 3 Tapered 2
35x2x16x9H DIN 5480or 28 UNI 221
SHAFT OPTIONSWith GM1 Mount
A1 Mount
A2 Mount
35x2x16 DIN 5480or
UNI 221
The graphs indicate the typical performance
characteristics of the 250 motor operating
with mineral oil with viscosity
40 cSt at 50°C.
PERFORMANCE
1 1/4” Straight Short1 1/4” Splined Long 1 1/4” Straight Long 1 1/2” Straight
95%
94%
92%90%
MECHANICAL EFFICIENCY IDLING AND BOOST PRESSURE
VOLUME EFFICIENCY
1 1/4” Splined ShortCode 17
SAE “C”OUTPUT END VIEW
MOTOR END VIEW
Code 28Code 67 Code 68 Code 58
STARTING AND LOW SPEED TORQUE
A3 Mount
DIMENSIONSSTANDARD VERSION
5. Motor Bearing: 11 = Roller Bearing (Standard) 13 = Spherical Roller Bearing (Standard in HD)
6. SAE C Bearing Option: 0= No Bearing (Standard) (No Side Load Allowed) 1 =Ball Bearings (Low Side Load Allowed) 2 = Spherical Roller (Side Load Allowed Consult Factory)
7. Shaft Seal: E = Without SV = Shaft Seal Protection VY = Viton I = Case Pressure Relief Valve 43psiDISTRIBUTOR CODE 8. Distributor: D36 (Low Speed) - Standard - See Distributor Option
9. Tachometer: K = Predisposed for tachometer J = Mechanical Tach. mount JB2 = Mount for BEI encoder E25 BA (type 6R) JB3 = Mount for Proximity switch up to 16 pulses per rev.ASSEMBLY CODES10. Direction of shaft rotation: standard motors are supplied with clockwise rotation (viewedfromshaftend)withflowinportA,outportB. No code = Clockwise L = Counter-Clockwise
11. Distributor cover position: No code = Position DM1 DM~ = Other position
Inches17 = 11/4” Splined Short67 = 11/4” Splined Long28 = 11/4” Straight Short68 = 11/4” Straight Long58 = 11/2” Straight
ORDERING CODES
SHAFT SPEED (rpm)PISTON Ø (mm)
The graph refers to the motor with roller bearings (option H). Note that the average lifetime of a bearing (B50 lifetime) is approximately 5 times the B10 lifetime.
BEARING LIFETIME
Motor bearing life on the HD ver-sion approx. double than standard version (consult factory for actual hrs life) 0 200 400 600 800 1000
100
1,000
10,000
100,0001,000,000
200
500
2,0005,000
HOURS
25 30 35 40 45 50 55 60 65
340
400
450
500
4000
2000
1000
3000
5000
280
240
200
150
1. Motor Type 1 = FS15 2 = FS15HD
2. Body Type A1 = Flangeless Mount A2 = Flange Mount A3 = SAE C 2/4 Bolt
3. Displacement - See motor spec. table
4. Shaft Options: Metric 7 = Male 35-2-16 DIN 5480 (std)1 = Male 28 UNI 2219 = Female 35-2-16 DIN 54803 = Female 28 UNI 2212 = Tapered Key8 = Parallel Keyed
D36