From Edentulous Maxilla To Fixed Teeth With Guide …...Guide System And Cad /Cam ISUS Bridge Case...
1
Mr. Boris Edelmann SmartDent Düsseldorf, Duisburg, Roermond [email protected] Planing with SimPlant® 13,24 3,8x13 - 16,21 3.8x11 15,26, 4,3x11 The Camlog® Guide System fitting and fixing on bone The red and white aesthetic was achieved by an individual multi-colored gingiva composite design. CAD/CAM manufactured ISUS bridge after removing Guide System a. 5 months imp. p. open tray EDELMANN, B private practise, düsseldorf, duisburg, roermond, germany - netherlands FELDMANN, M private practise, düsseldorf, duisburg, roermond germany - netherlands VOSSEN, K private practise, wegberg germany From Edentulous Maxilla To Fixed Teeth With Camlog® Guide System And Cad /Cam ISUS Bridge Case Report At a 54 year old female patient all the teeth had been removed in the upper jaw. The teeth were pre-damaged peridontal and caries and no longer worthy of preservation. After four months of regeneration, navigated planning with Materialise SimPlant was prepared on a CT record. Manufacture of the final prosthetic Taking an impression with custom tray and prior blocking of the impression post. In the second session, a provisionally bite registration was taken with screw base. An Esthetic restoration had been prepared after a determination relation, following the fitting for the electronic functional diagnosis (Freecoder Blue Fox® System) related to the hinge axis, joint space measurement and registration of the movement path. Objectives Materials and methods Results The patient request of fixed teeth ended up in a conditionally removable hybrid bridge. After evaluation the FAL-data repositioning has been made under computer control. The CAD CAM manufactured ISUS bridge made of grade 4 titanium includes angled screws. Therefore we could make sure that the screw holes are located on an occlusal position and not in the esthetic zone. Anterior have been used e.max crowns and posterior composite veneers from GC Gradia. Before Treatment 3 months later 6 weeks after impl.
Transcript of From Edentulous Maxilla To Fixed Teeth With Guide …...Guide System And Cad /Cam ISUS Bridge Case...
EDELMANN, B private practise, düsseldorf, duisburg, roermond, ! ! ! ! ! ! germany - netherlands ! ! ! FELDMANN, M private practise, düsseldorf, duisburg, roermond! ! ! ! ! ! germany - netherlands! ! ! VOSSEN, K private practise, wegberg! ! ! ! ! ! germany
Mr. Boris EdelmannSmartDent
Düsseldorf, Duisburg, [email protected]
From Edentulous Maxilla To Fixed Teeth With Camlog® Guide System And Cad /Cam ISUS BridgeCase Report
At a 54 year old female patient all the teeth had been removed in the upper jaw.The teeth were pre-damaged peridontal and caries and no longer worthy of preservation.After four months of regeneration, navigated planning with Materialise SimPlant was prepared on a CT record.
Manufacture of the final prostheticTaking an impression with custom tray and prior blocking of the impression post. In the second session, a provisionally bite registration was taken with screw base.An Esthetic restoration had been prepared after a determination relation, following the fitting for the electronic functional diagnosis (Freecoder Blue Fox® System) related to the hinge axis, joint space measurement and registration of the movement path.
Planing with SimPlant®
The Camlog® Guide System fitting and fixing on bone
The red and white aesthetic was achieved by an individual multi-colored gingiva composite design.
CAD/CAM manufactured ISUS bridge
Objectives
Materials and methods
ResultsThe patient request of fixed teeth ended up in a conditionally removable hybrid bridge.
After evaluation the FAL-data repositioning has been made under computer control.
The CAD CAM manufactured ISUS bridge made of grade 4 titanium includes angled screws. Therefore we could make sure that the screw holes are located on an occlusal position and not in the esthetic zone.Anterior have been used e.max crowns and posterior composite veneers from GC Gradia.
a. 5 months imp. p. open tray
13,24 3,8x13 - 16,21 3.8x1115,26, 4,3x11
after 6 weeks
EDELMANN, B private practise, düsseldorf, duisburg, roermond, ! ! ! ! ! ! germany - netherlands ! ! ! FELDMANN, M private practise, düsseldorf, duisburg, roermond! ! ! ! ! ! germany - netherlands! ! ! VOSSEN, K private practise, wegberg! ! ! ! ! ! germany
Mr. Boris EdelmannSmartDent
Düsseldorf, Duisburg, [email protected]
From Edentulous Maxilla To Fixed Teeth With Camlog® Guide System And Cad /Cam ISUS BridgeCase Report
At a 54 year old female patient all the teeth had been removed in the upper jaw.The teeth were pre-damaged peridontal and caries and no longer worthy of preservation.After four months of regeneration, navigated planning with Materialise SimPlant was prepared on a CT record.
Manufacture of the final prostheticTaking an impression with custom tray and prior blocking of the impression post. In the second session, a provisionally bite registration was taken with screw base.An Esthetic restoration had been prepared after a determination relation, following the fitting for the electronic functional diagnosis (Freecoder Blue Fox® System) related to the hinge axis, joint space measurement and registration of the movement path.
Planing with SimPlant®
The Camlog® Guide System fitting and fixing on bone
The red and white aesthetic was achieved by an individual multi-colored gingiva composite design.
CAD/CAM manufactured ISUS bridge
Objectives
Materials and methods
ResultsThe patient request of fixed teeth ended up in a conditionally removable hybrid bridge.
After evaluation the FAL-data repositioning has been made under computer control.
The CAD CAM manufactured ISUS bridge made of grade 4 titanium includes angled screws. Therefore we could make sure that the screw holes are located on an occlusal position and not in the esthetic zone.Anterior have been used e.max crowns and posterior composite veneers from GC Gradia.
a. 5 months imp. p. open tray
13,24 3,8x13 - 16,21 3.8x1115,26, 4,3x11
after 6 weeks
EDELMANN, B private practise, düsseldorf, duisburg, roermond, ! ! ! ! ! ! germany - netherlands ! ! ! FELDMANN, M private practise, düsseldorf, duisburg, roermond! ! ! ! ! ! germany - netherlands! ! ! VOSSEN, K private practise, wegberg! ! ! ! ! ! germany
Mr. Boris EdelmannSmartDent
Düsseldorf, Duisburg, [email protected]
From Edentulous Maxilla To Fixed Teeth With Camlog® Guide System And Cad /Cam ISUS BridgeCase Report
At a 54 year old female patient all the teeth had been removed in the upper jaw.The teeth were pre-damaged peridontal and caries and no longer worthy of preservation.After four months of regeneration, navigated planning with Materialise SimPlant was prepared on a CT record.
Manufacture of the final prostheticTaking an impression with custom tray and prior blocking of the impression post. In the second session, a provisionally bite registration was taken with screw base.An Esthetic restoration had been prepared after a determination relation, following the fitting for the electronic functional diagnosis (Freecoder Blue Fox® System) related to the hinge axis, joint space measurement and registration of the movement path.
Planing with SimPlant®
The Camlog® Guide System fitting and fixing on bone
The red and white aesthetic was achieved by an individual multi-colored gingiva composite design.
CAD/CAM manufactured ISUS bridge
Objectives
Materials and methods
ResultsThe patient request of fixed teeth ended up in a conditionally removable hybrid bridge.
After evaluation the FAL-data repositioning has been made under computer control.
The CAD CAM manufactured ISUS bridge made of grade 4 titanium includes angled screws. Therefore we could make sure that the screw holes are located on an occlusal position and not in the esthetic zone.Anterior have been used e.max crowns and posterior composite veneers from GC Gradia.
a. 5 months imp. p. open tray
13,24 3,8x13 - 16,21 3.8x1115,26, 4,3x11
after 6 weeks
EDELMANN, B private practise, düsseldorf, duisburg, roermond, ! ! ! ! ! ! germany - netherlands ! ! ! FELDMANN, M private practise, düsseldorf, duisburg, roermond! ! ! ! ! ! germany - netherlands! ! ! VOSSEN, K private practise, wegberg! ! ! ! ! ! germany
Mr. Boris EdelmannSmartDent
Düsseldorf, Duisburg, [email protected]
From Edentulous Maxilla To Fixed Teeth With Camlog® Guide System And Cad /Cam ISUS BridgeCase Report
At a 54 year old female patient all the teeth had been removed in the upper jaw.The teeth were pre-damaged peridontal and caries and no longer worthy of preservation.After four months of regeneration, navigated planning with Materialise SimPlant was prepared on a CT record.
Manufacture of the final prostheticTaking an impression with custom tray and prior blocking of the impression post. In the second session, a provisionally bite registration was taken with screw base.An Esthetic restoration had been prepared after a determination relation, following the fitting for the electronic functional diagnosis (Freecoder Blue Fox® System) related to the hinge axis, joint space measurement and registration of the movement path.
Planing with SimPlant®
The Camlog® Guide System fitting and fixing on bone
The red and white aesthetic was achieved by an individual multi-colored gingiva composite design.
CAD/CAM manufactured ISUS bridge
Objectives
Materials and methods
ResultsThe patient request of fixed teeth ended up in a conditionally removable hybrid bridge.
After evaluation the FAL-data repositioning has been made under computer control.
The CAD CAM manufactured ISUS bridge made of grade 4 titanium includes angled screws. Therefore we could make sure that the screw holes are located on an occlusal position and not in the esthetic zone.Anterior have been used e.max crowns and posterior composite veneers from GC Gradia.
a. 5 months imp. p. open tray
13,24 3,8x13 - 16,21 3.8x1115,26, 4,3x11
after 6 weeks
EDELMANN, B private practise, düsseldorf, duisburg, roermond, ! ! ! ! ! ! germany - netherlands ! ! ! FELDMANN, M private practise, düsseldorf, duisburg, roermond! ! ! ! ! ! germany - netherlands! ! ! VOSSEN, K private practise, wegberg! ! ! ! ! ! germany
Mr. Boris EdelmannSmartDent
Düsseldorf, Duisburg, [email protected]
From Edentulous Maxilla To Fixed Teeth With Camlog® Guide System And Cad /Cam ISUS BridgeCase Report
At a 54 year old female patient all the teeth had been removed in the upper jaw.The teeth were pre-damaged peridontal and caries and no longer worthy of preservation.After four months of regeneration, navigated planning with Materialise SimPlant was prepared on a CT record.
Manufacture of the final prostheticTaking an impression with custom tray and prior blocking of the impression post. In the second session, a provisionally bite registration was taken with screw base.An Esthetic restoration had been prepared after a determination relation, following the fitting for the electronic functional diagnosis (Freecoder Blue Fox® System) related to the hinge axis, joint space measurement and registration of the movement path.
Planing with SimPlant®
The Camlog® Guide System fitting and fixing on bone
The red and white aesthetic was achieved by an individual multi-colored gingiva composite design.
CAD/CAM manufactured ISUS bridge
Objectives
Materials and methods
ResultsThe patient request of fixed teeth ended up in a conditionally removable hybrid bridge.
After evaluation the FAL-data repositioning has been made under computer control.
The CAD CAM manufactured ISUS bridge made of grade 4 titanium includes angled screws. Therefore we could make sure that the screw holes are located on an occlusal position and not in the esthetic zone.Anterior have been used e.max crowns and posterior composite veneers from GC Gradia.
a. 5 months imp. p. open tray
13,24 3,8x13 - 16,21 3.8x1115,26, 4,3x11
after 6 weeks
EDELMANN, B private practise, düsseldorf, duisburg, roermond, ! ! ! ! ! ! germany - netherlands ! ! ! FELDMANN, M private practise, düsseldorf, duisburg, roermond! ! ! ! ! ! germany - netherlands! ! ! VOSSEN, K private practise, wegberg! ! ! ! ! ! germany
Mr. Boris EdelmannSmartDent
Düsseldorf, Duisburg, [email protected]
From Edentulous Maxilla To Fixed Teeth With Camlog® Guide System And Cad /Cam ISUS BridgeCase Report
At a 54 year old female patient all the teeth had been removed in the upper jaw.The teeth were pre-damaged peridontal and caries and no longer worthy of preservation.After four months of regeneration, navigated planning with Materialise SimPlant was prepared on a CT record.
Manufacture of the final prostheticTaking an impression with custom tray and prior blocking of the impression post. In the second session, a provisionally bite registration was taken with screw base.An Esthetic restoration had been prepared after a determination relation, following the fitting for the electronic functional diagnosis (Freecoder Blue Fox® System) related to the hinge axis, joint space measurement and registration of the movement path.
Planing with SimPlant®
The Camlog® Guide System fitting and fixing on bone
The red and white aesthetic was achieved by an individual multi-colored gingiva composite design.
CAD/CAM manufactured ISUS bridge
Objectives
Materials and methods
ResultsThe patient request of fixed teeth ended up in a conditionally removable hybrid bridge.
After evaluation the FAL-data repositioning has been made under computer control.
The CAD CAM manufactured ISUS bridge made of grade 4 titanium includes angled screws. Therefore we could make sure that the screw holes are located on an occlusal position and not in the esthetic zone.Anterior have been used e.max crowns and posterior composite veneers from GC Gradia.
a. 5 months imp. p. open tray
13,24 3,8x13 - 16,21 3.8x1115,26, 4,3x11
after 6 weeks
EDELMANN, B private practise, düsseldorf, duisburg, roermond, ! ! ! ! ! ! germany - netherlands ! ! ! FELDMANN, M private practise, düsseldorf, duisburg, roermond! ! ! ! ! ! germany - netherlands! ! ! VOSSEN, K private practise, wegberg! ! ! ! ! ! germany
Mr. Boris EdelmannSmartDent
Düsseldorf, Duisburg, [email protected]
From Edentulous Maxilla To Fixed Teeth With Camlog® Guide System And Cad /Cam ISUS BridgeCase Report
At a 54 year old female patient all the teeth had been removed in the upper jaw.The teeth were pre-damaged peridontal and caries and no longer worthy of preservation.After four months of regeneration, navigated planning with Materialise SimPlant was prepared on a CT record.
Manufacture of the final prostheticTaking an impression with custom tray and prior blocking of the impression post. In the second session, a provisionally bite registration was taken with screw base.An Esthetic restoration had been prepared after a determination relation, following the fitting for the electronic functional diagnosis (Freecoder Blue Fox® System) related to the hinge axis, joint space measurement and registration of the movement path.
Planing with SimPlant®
The Camlog® Guide System fitting and fixing on bone
The red and white aesthetic was achieved by an individual multi-colored gingiva composite design.
CAD/CAM manufactured ISUS bridge
Objectives
Materials and methods
ResultsThe patient request of fixed teeth ended up in a conditionally removable hybrid bridge.
After evaluation the FAL-data repositioning has been made under computer control.
The CAD CAM manufactured ISUS bridge made of grade 4 titanium includes angled screws. Therefore we could make sure that the screw holes are located on an occlusal position and not in the esthetic zone.Anterior have been used e.max crowns and posterior composite veneers from GC Gradia.
a. 5 months imp. p. open tray
13,24 3,8x13 - 16,21 3.8x1115,26, 4,3x11
after 6 weeks
EDELMANN, B private practise, düsseldorf, duisburg, roermond, ! ! ! ! ! ! germany - netherlands ! ! ! FELDMANN, M private practise, düsseldorf, duisburg, roermond! ! ! ! ! ! germany - netherlands! ! ! VOSSEN, K private practise, wegberg! ! ! ! ! ! germany
Mr. Boris EdelmannSmartDent
Düsseldorf, Duisburg, [email protected]
From Edentulous Maxilla To Fixed Teeth With Camlog® Guide System And Cad /Cam ISUS BridgeCase Report
At a 54 year old female patient all the teeth had been removed in the upper jaw.The teeth were pre-damaged peridontal and caries and no longer worthy of preservation.After four months of regeneration, navigated planning with Materialise SimPlant was prepared on a CT record.
Manufacture of the final prostheticTaking an impression with custom tray and prior blocking of the impression post. In the second session, a provisionally bite registration was taken with screw base.An Esthetic restoration had been prepared after a determination relation, following the fitting for the electronic functional diagnosis (Freecoder Blue Fox® System) related to the hinge axis, joint space measurement and registration of the movement path.
Planing with SimPlant®
The Camlog® Guide System fitting and fixing on bone
The red and white aesthetic was achieved by an individual multi-colored gingiva composite design.
CAD/CAM manufactured ISUS bridge
Objectives
Materials and methods
ResultsThe patient request of fixed teeth ended up in a conditionally removable hybrid bridge.
After evaluation the FAL-data repositioning has been made under computer control.
The CAD CAM manufactured ISUS bridge made of grade 4 titanium includes angled screws. Therefore we could make sure that the screw holes are located on an occlusal position and not in the esthetic zone.Anterior have been used e.max crowns and posterior composite veneers from GC Gradia.
a. 5 months imp. p. open tray
13,24 3,8x13 - 16,21 3.8x1115,26, 4,3x11
after removing Guide System
EDELMANN, B private practise, düsseldorf, duisburg, roermond, ! ! ! ! ! ! germany - netherlands ! ! ! FELDMANN, M private practise, düsseldorf, duisburg, roermond! ! ! ! ! ! germany - netherlands! ! ! VOSSEN, K private practise, wegberg! ! ! ! ! ! germany
Mr. Boris EdelmannSmartDent
Düsseldorf, Duisburg, [email protected]
From Edentulous Maxilla To Fixed Teeth With Camlog® Guide System And Cad /Cam ISUS BridgeCase Report
At a 54 year old female patient all the teeth had been removed in the upper jaw.The teeth were pre-damaged peridontal and caries and no longer worthy of preservation.After four months of regeneration, navigated planning with Materialise SimPlant was prepared on a CT record.
Manufacture of the final prostheticTaking an impression with custom tray and prior blocking of the impression post. In the second session, a provisionally bite registration was taken with screw base.An Esthetic restoration had been prepared after a determination relation, following the fitting for the electronic functional diagnosis (Freecoder Blue Fox® System) related to the hinge axis, joint space measurement and registration of the movement path.
Planing with SimPlant®
The Camlog® Guide System fitting and fixing on bone
The red and white aesthetic was achieved by an individual multi-colored gingiva composite design.
CAD/CAM manufactured ISUS bridge
Objectives
Materials and methods
ResultsThe patient request of fixed teeth ended up in a conditionally removable hybrid bridge.
After evaluation the FAL-data repositioning has been made under computer control.
The CAD CAM manufactured ISUS bridge made of grade 4 titanium includes angled screws. Therefore we could make sure that the screw holes are located on an occlusal position and not in the esthetic zone.Anterior have been used e.max crowns and posterior composite veneers from GC Gradia.
a. 5 months imp. p. open tray
13,24 3,8x13 - 16,21 3.8x1115,26, 4,3x11
after 6 weeks
EDELMANN, B private practise, düsseldorf, duisburg, roermond, ! ! ! ! ! ! germany - netherlands ! ! ! FELDMANN, M private practise, düsseldorf, duisburg, roermond! ! ! ! ! ! germany - netherlands! ! ! VOSSEN, K private practise, wegberg! ! ! ! ! ! germany
Mr. Boris EdelmannSmartDent
Düsseldorf, Duisburg, [email protected]
From Edentulous Maxilla To Fixed Teeth With Camlog® Guide System And Cad /Cam ISUS BridgeCase Report
At a 54 year old female patient all the teeth had been removed in the upper jaw.The teeth were pre-damaged peridontal and caries and no longer worthy of preservation.After four months of regeneration, navigated planning with Materialise SimPlant was prepared on a CT record.
Manufacture of the final prostheticTaking an impression with custom tray and prior blocking of the impression post. In the second session, a provisionally bite registration was taken with screw base.An Esthetic restoration had been prepared after a determination relation, following the fitting for the electronic functional diagnosis (Freecoder Blue Fox® System) related to the hinge axis, joint space measurement and registration of the movement path.
Planing with SimPlant®
The Camlog® Guide System fitting and fixing on bone
The red and white aesthetic was achieved by an individual multi-colored gingiva composite design.
CAD/CAM manufactured ISUS bridge
Objectives
Materials and methods
ResultsThe patient request of fixed teeth ended up in a conditionally removable hybrid bridge.
After evaluation the FAL-data repositioning has been made under computer control.
The CAD CAM manufactured ISUS bridge made of grade 4 titanium includes angled screws. Therefore we could make sure that the screw holes are located on an occlusal position and not in the esthetic zone.Anterior have been used e.max crowns and posterior composite veneers from GC Gradia.
a. 5 months imp. p. open tray
13,24 3,8x13 - 16,21 3.8x1115,26, 4,3x11
after 6 weeks
EDELMANN, B private practise, düsseldorf, duisburg, roermond, ! ! ! ! ! ! germany - netherlands ! ! ! FELDMANN, M private practise, düsseldorf, duisburg, roermond! ! ! ! ! ! germany - netherlands! ! ! VOSSEN, K private practise, wegberg! ! ! ! ! ! germany
Mr. Boris EdelmannSmartDent
Düsseldorf, Duisburg, [email protected]
From Edentulous Maxilla To Fixed Teeth With Camlog® Guide System And Cad /Cam ISUS BridgeCase Report
At a 54 year old female patient all the teeth had been removed in the upper jaw.The teeth were pre-damaged peridontal and caries and no longer worthy of preservation.After four months of regeneration, navigated planning with Materialise SimPlant was prepared on a CT record.
Manufacture of the final prostheticTaking an impression with custom tray and prior blocking of the impression post. In the second session, a provisionally bite registration was taken with screw base.An Esthetic restoration had been prepared after a determination relation, following the fitting for the electronic functional diagnosis (Freecoder Blue Fox® System) related to the hinge axis, joint space measurement and registration of the movement path.
Planing with SimPlant®
The Camlog® Guide System fitting and fixing on bone
The red and white aesthetic was achieved by an individual multi-colored gingiva composite design.
CAD/CAM manufactured ISUS bridge
Objectives
Materials and methods
ResultsThe patient request of fixed teeth ended up in a conditionally removable hybrid bridge.
After evaluation the FAL-data repositioning has been made under computer control.
The CAD CAM manufactured ISUS bridge made of grade 4 titanium includes angled screws. Therefore we could make sure that the screw holes are located on an occlusal position and not in the esthetic zone.Anterior have been used e.max crowns and posterior composite veneers from GC Gradia.
a. 5 months imp. p. open tray
13,24 3,8x13 - 16,21 3.8x1115,26, 4,3x11
after 6 weeks
EDELMANN, B private practise, düsseldorf, duisburg, roermond, ! ! ! ! ! ! germany - netherlands ! ! ! FELDMANN, M private practise, düsseldorf, duisburg, roermond! ! ! ! ! ! germany - netherlands! ! ! VOSSEN, K private practise, wegberg! ! ! ! ! ! germany
Mr. Boris EdelmannSmartDent
Düsseldorf, Duisburg, [email protected]
From Edentulous Maxilla To Fixed Teeth With Camlog® Guide System And Cad /Cam ISUS BridgeCase Report
At a 54 year old female patient all the teeth had been removed in the upper jaw.The teeth were pre-damaged peridontal and caries and no longer worthy of preservation.After four months of regeneration, navigated planning with Materialise SimPlant was prepared on a CT record.
Manufacture of the final prostheticTaking an impression with custom tray and prior blocking of the impression post. In the second session, a provisionally bite registration was taken with screw base.An Esthetic restoration had been prepared after a determination relation, following the fitting for the electronic functional diagnosis (Freecoder Blue Fox® System) related to the hinge axis, joint space measurement and registration of the movement path.
Planing with SimPlant®
The Camlog® Guide System fitting and fixing on bone
The red and white aesthetic was achieved by an individual multi-colored gingiva composite design.
CAD/CAM manufactured ISUS bridge
Objectives
Materials and methods
ResultsThe patient request of fixed teeth ended up in a conditionally removable hybrid bridge.
After evaluation the FAL-data repositioning has been made under computer control.The CAD CAM manufactured ISUS bridge made of grade 4 titanium includes angled screws. Therefore we could make sure that the screw holes are located on an occlusal position and not in the esthetic zone.Anterior have been used e.max crowns and posterior composite veneers from GC Gradia.
a. 5 months imp. p. open tray
13,24 3,8x13 - 16,21 3.8x1115,26, 4,3x11
after removing Guide System
Before Treatment 3 months later 6 weeks after impl.
