FRISO KRAMER DIRECT CLASS 1/II IMPORTANT SPECIFICATIONS€¦ · 40°C 0,22 FRISO KRAMER DIRECT...
5
m 2 65 3-5m 60-76 mm IEC 598 80 20 IP.. Ta temp O mm 0,22 40°C FRISO KRAMER DIRECT CLASS 1/II Lightsource: LED Voltage: 230 V AC 50 Hz Power factor: > 0,90 Pole diameter: 60 mm Driver: Philips Xitanium Required tools 660 mm 458 mm 475 mm Ø 60 mm Friso Kramer Direct IMPORTANT 1. Follow the instructions of this manual 2. Use IEC tools 3. Replace defective parts 4. Point the hexbolt towards the street 5. The hexbolts have to be tightened with a torque of 4-5 Nm 6. Cable: 1,5 mm 2 or 1,0 mm 2 with rated voltage and current: 250V / > 1A 7. Terminal block in the pole is not included 8. Installation requires advice from a qualified technician 9. Lightwell B.V. retains final explanation rights 10. The external cable of this luminaire can not be replaced. If the cable is damaged, the luminaire should be removed 11. The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person SPECIFICATIONS 1. LED power is set in the factory 2. Light color standard 3000K/4000K 3. CLO, Dimprofile is set in the factory PARTS 1. Luminaire with asymmetric optics 2. TOP LID: 8718843016868 (RAL7040) 3. TOP SCREW: 8718843016936 (RAL7040) 4. LED module: article number on cord and on LED module 5. DRIVER 9 kg IP65 IK09 Ø19 LW-FKLD TOOL 8718843020858 16 Nm Torque 8718843017353 - LW-FKLD manual C1-C2 EN 1.3
Transcript of FRISO KRAMER DIRECT CLASS 1/II IMPORTANT SPECIFICATIONS€¦ · 40°C 0,22 FRISO KRAMER DIRECT...
m2
65 3-5m 60-76mm IEC 598 80 20
IP..Tatemp
O mm
0,2240°C
FRISO KRAMER DIRECT CLASS 1/IILightsource: LEDVoltage: 230 V AC 50 HzPower factor: > 0,90Pole diameter: 60 mmDriver : Philips Xitanium
Required tools660 mm
458
mm
475
mm
Ø 60 mmFriso Kramer Direct
IMPORTANT1. Follow the instructions of this manual2. Use IEC tools3. Replace defective parts4. Point the hexbolt towards the street5. The hexbolts have to be tightened with a torque of 4-5 Nm6. Cable: 1,5 mm2 or 1,0 mm2
with rated voltage and current: 250V / > 1A 7. Terminal block in the pole is not included8. Installation requires advice from a qualified technician9. Lightwell B.V. retains final explanation rights10. The external cable of this luminaire can not be replaced. If the cable is damaged, the luminaire should be removed11. The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person
SPECIFICATIONS1. LED power is set in the factory 2. Light color standard 3000K/4000K3. CLO, Dimprofile is set in the factory
PARTS1. Luminaire with asymmetric optics2. TOP LID: 8718843016868 (RAL7040) 3. TOP SCREW: 8718843016936 (RAL7040) 4. LED module: article number oncord and on LED module5. DRIVER
9 kg
IP65IK09
Ø19
LW-FKLD TOOL871884302085816 Nm Torque
8718843017353 - LW-FKLD manual C1-C2 EN 1.3
INSTALLATION1
2
21 Hexbolt facing street*
1 2BROWN - L1
BLUE - NYELLOW-GREEN - G
ROADpoint road sticker towards street
3A
1 2BROWN - L1
BLUE - N
3B
INFORMATION TERMINAL BLOCK:1. 3 or 4 pins screw terminal2. Rated voltage and current: 250V / > 1A3. Complying with standard EN 60998-2-1 or EN 60998-2-2
8718843017353 - LW-FKLD manual C1-C2 EN 1.3
OPEN COVER1
Ø19
2
use cloth
8718843017353 - LW-FKLD manual C1-C2 EN 1.3
Chemicals that can outgas hydrocarbons (e.g., toluene, benzene, xylene)
Methyl acetate or ethyl acetate (e.g., nail polish remover)
Cyanoacrylates (e.g., “Superglue”)
Glycol ethers and dipropylene glycol monomethyl ether (e.g., electronics cleaners)
Formaldehyde or butadiene (e.g., PLIOBOND® adhesive)
Chlorine, including bleach-containing cleaners and sprays
Table 1: Common chemicals with known LED compatibility issues
Base Material TypeOK In XLamp
Designs*Outgas Tested
Issues Found
Issues Suspected
Acetic acid Acid Yes
Acrylic rubber Rubber/plastic seal Yes
Acetone Manufacturing material Yes
Ammonia Alkaline Yes
Benzene Solvent Yes
Butadiene rubber Rubber/plastic seal Yes
Butyl rubber Rubber/plastic seal Yes
Chlorinated polyethylene Rubber/plastic seal Yes
Chlorobutyl Rubber/plastic seal Yes
Chlorosulphonated rubber Rubber/plastic seal Yes
Cyanoacrylate Sealant & adhesive Yes Yes
Dichloromethane Solvent Yes
Epichlorhydrin Rubber/plastic seal Yes
Gasoline Solvent Yes
Halogenated hydrocarbons (containing F, Cl, Br elements)/miscellaneous Yes Yes
Hydrochloric acid Acid Yes
MEK (methyl ethyl ketone) Solvent Yes
MIBK (methyl isobutyl ketone) Solvent Yes
Mineral spirits Solvent Yes
Nitric acid Acid Yes
Petroleum Oil/lubricant Yes
Potassium hydroxide Alkaline Yes
Silicone oil Oil/lubricant Yes
Sodium hydroxide Alkaline Yes
Sulfuric acid Acid Yes
Tetracholoromethane Solvent Yes
Tetradecylamine Yes
Toluene Solvent Yes
Trimethylhexamethylene diamine Yes
Xylene Solvent Yes
Table 5: Base material compatibility
CLEANING THE LUMINAIREThe detergents in the table below are discouraged. Use of these detergents may cause damage to the LEDs over time.
8718843017353 - LW-FKLD manual C1-C2 EN 1.3
CLOSE COVER1
use cloth
!! close with 16 Nm !!
16 Nm Torque
8718843017353 - LW-FKLD manual C1-C2 EN 1.3
