• DESIGNED BY BENARTEX • FINISHED SIZE: 60” X 75” • PATTERN AVAILABLE IN

JULY 2019 AT BENARTEX.COM

free pattern

MusicFEEL THE

BENARTEX, LLC • 132 WEST 36TH STREET, 4TH FLOOR • NEW YORK, NY 10018 • T:212-840-3250 • WWW.BENARTEX.COM

SAMPLE KEY/SKU QTY CUT CUT PIECES VIA WOF

A

C

E

B

D

Musical Boxes7853-12 Black

Musical Confetti 7849-12 Black

Soundwaves7847-10Red

Piano Play7852-10Black/Red

Musical Stripe7848-12Black

BLOCK ASSEMBLY PROJECT USES PRECISE 1/4” SEAMS. TEST YOUR SEAM ALLOWANCE BY CUTTING (2) 2-1/2” X 5” RECTANGLES. STITCH THEM TOGETHER ALONG THE 5” LENGTH. AT THE MIDPOINT, MEASURE ACROSS THE UNIT. IT SHOULD BE EXACTLY 4-1/2” WIDE. IF NOT, ADJUST YOUR SEAM ALLOWANCE AND REPEAT.

Fussy cut (12) 7-1/2” blocks.

(6) 4-1/2” x WOF strips.*(3) 3-1/2” x 42-1/2” WOF strips, piece as needed.(3) 3-1/2” x WOF strips. Sub-cut (8) 3-1/2” x 12-1/2” strips.

(7) 2-1/2” x WOF strips, BINDING

(5) 3-1/2” x WOF strips. Sub-cut (24) 3-1/2” x 7-1/2” strips.(8) 3-1/2” x WOF strips. Sub-cut (24) 3-1/2” 13-1/2” strips.

(2) 5-1/2” x 79” LOF strips.(2) 5-1/2” x 64” LOF strips.

* SEW STRIPS VIA SHORT ENDS THEN GO TO BORDER ASSEMBLY WOF/LOF=WIDTH/LENGTH OF FABRIC

Quilt Diagram

Note: If this Benartex pattern is included in a kit, any questions about the kit should be addressed to the vendor from whom you bought it.

1-3/8yds

2-1/4 yds

3/4 yd

1-5/8 yds

5/8 yd

FINISHED SIZE: 60” X 75”

FINISHING Cut batting and backing 3” larger than top on all sides. Layer backing, batting and top together and baste or pin. When quilting is completed, trim excess batting and backing. Bind as usual.

BORDER ASSEMBLY MEASURE WIDTH AND LENGTH OF THE QUILT TOP TO ENSURE C & D BORDER SIZES, BELOW ARE OUR CUTTING SIZES.

D

D

D

1 1 1

1 1 1

1 1 1

1 1 1

D

C

C

C

C

C C

C C

C C

C C

C

C C

Block Assembly 1. Sew (1) B 3-1/2” x 7-1/2” strip to each side of (1) A 7-1/2” x 7-1/2” block. Sew (1) B 3-1/2” x 13-1/2” strip to the top and to the bottom of the A block. Trim the block to measure 12-1/2” x 12-1/2” to make (1) Block One square.

2. Repeat Step 1 to make (12) Block One squares total.

AB B

B

B

Block Onemake 12

Trim blockto measure12 ½” x 12 ½”AFTER addingborders

Quilt Assembly 3. Sew (3) Block One squares and (2) C 3-1/2” x 12-1/2” strips together, alternating them, to make (1) Row. Repeat to make (4) rows total.

4. Sew the (4) rows and (3) C 3-1/2” x 42-1/2” strips together lengthwise and alternating them, to make the Center Block.

5. Sew (1) C 4-1/2” x (57-1/2”) strip to each side of the Center Block. Sew (1) C 4-1/2” x (50-1/2”) strips to the top and bottom of Center Block.

6. Center (1) D 5-1/2” x (79”) strip on one (1) side of the Center Block and pin in place. Start sewing the strip a 1/4” from the top edge of the block and stop a 1/4” from the bottom edge. DO NOT TRIM THE EXCESS. Repeat with the opposite side.

7. Repeat Step 6 to sew (1) D 5-1/2” x (64”) strip to the top and to the bottom of the Center Block, making sure to stop and start 1/4” away from each end of the block. To miter each corner, fold the Center Block on a diagonal, wrong side together. This should line up the strips from adjacent sides.

Quilt To

p

Folded on

the D

iagonal

8. Starting at the sewn seam (represented by the arrow in the figure), draw a 45-degree line to the edge of the fabric. Sew on the drawn line. Trim the excess fabric leaving a 1/4” seam. Repeat this step with the remaining corners to make the quilt top.