FORD6 · PDF file · 2017-12-13The FORD6 firmware for DS4+ is compatible with...

FORD6

INSTALLATION GUIDE

This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle’s electrical system and components.

2017-12-13

© 2017 Directed, Vista CA

DS4+

Designed by Installers for Installers

ContentsWarning! Safety first ....................................................................................................................... 3Introduction .................................................................................................................................... 4

Pre-installation and application warnings ..................................................................................... 4Vehicle application guide ........................................................................................................... 5

Wiring connections ......................................................................................................................... 6Main harness (H1), 12-pin black connector .................................................................................. 6Relay harness (H2), 10-pin white connector .................................................................................. 6Data harness (H3), 8-pin white connector ..................................................................................... 6Analog input/output harness (H4), 22-pin white connector ............................................................. 7RF Port harness (H5), 2-pin white connector .................................................................................. 7D2D harness (H6), 4-pin white (1) and black (2) connectors ........................................................... 7Temperature sensor harness (H7), 2-pin black connector ................................................................ 7

Installation (wiring diagrams, fuse selection & vehicle wiring reference charts) ........................................ 8Type 1 with T-Harness (THFON1) ................................................................................................ 8Type 1 ..................................................................................................................................... 9Type 2 with T-Harness (THFON1) .............................................................................................. 21Type 2 ................................................................................................................................... 22Type 3 .................................................................................................................................. 31Type 4 ................................................................................................................................... 35Type 5 with T-Harness (THFON1) .............................................................................................. 38Type 6 ................................................................................................................................... 41Type 7 ................................................................................................................................... 43Type 8 ................................................................................................................................... 45Type 9 ................................................................................................................................... 47Type 10 ................................................................................................................................. 49

Key2GO ...................................................................................................................................... 51Understanding the difference between a Ford 80 & 40 bit ................................................................. 51

What does it mean? ............................................................................................................... 51How do I differentiate between the 40 & 80 bit? ......................................................................... 51

Configuring the system................................................................................................................... 52Important! .............................................................................................................................. 52Vehicles equipped with a manual transmission ............................................................................ 52RF Systems ............................................................................................................................. 528504D Combo Sensor ............................................................................................................. 52When used in conjunction with SmartStart .................................................................................. 53D2D port configuration ............................................................................................................ 53Module programming - Using 2 Keys ......................................................................................... 54Module programming - 1-Key programming using Key2GO ......................................................... 55LED diagnostics and troubleshooting .......................................................................................... 56Soft reset ................................................................................................................................ 58Hard reset .............................................................................................................................. 58

Learning the Tach (not needed with Virtual Tach) ............................................................................... 59Initializing Virtual Tach (not needed with hardwired or data tach applications) ..................................... 59Limited lifetime consumer warranty .................................................................................................. 60Quick Reference Guide .................................................................................................................. 61

3 DS4+ FORD6© 2017-12-13 Directed. All rights reserved.

Warning! Safety firstThe following safety warnings must be observed at all times:

• Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer.• When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never

operate the system in an area that does not have adequate ventilation.

The following precautions are the sole responsibility of the user; however, authorized Directed dealers should:• Never use a test light or logic probe when installing this unit. Always use a multimeter. • Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage). • When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote start system must

be disabled using the installed toggle switch. It is the user’s sole responsibility to properly handle and keep out of reach from children all remote controls to assure that the system does not unintentionally remote start the vehicle.

• USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST REMAIN CLOSED AT ALL TIMES.

Use of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, or death. Except when performing the Safety Check outlined in this installation guide, (1) Never remotely start the vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user is responsible for having the neutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotely start while the car is in gear. This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined in this product installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the user to fix the problem immediately.

OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. IMMEDIATELY CEASE THE USE OF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED REMOTE START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS.

Remote starters for manual transmission pose significant risks if not properly installed and operated. When testing to ensure the installation is working properly, only remote start the vehicle in neutral gear, on a flat surface and with a functional, fully engaged parking brake. Do not allow anyone to stand in front of or behind the vehicle.

This product should not be installed in any convertible vehicles, soft or hard top with a manual transmission. Installation in such vehicles may pose certain risk.


IntroductionThe FORD6 firmware for DS4+ is compatible with specific Ford and Lincoln vehicles. It is a complete solution for remote start, security (when security features are enabled), bypass, and features built in Bluetooth 4.0 allowing you to configure and control your system. This guide provides information on the installation of the module using FORD6. Please refer to the DirectLink application or www.directechs.com for more information about which configuration is best for your application.

Warning! This module is designed to be configured using the DirectLink application for mobile devices, however it can also be configured using the web tool located at www.directechs.com. To download the DirectLink mobile application, please visit the Google Play or Apple store.

Pre-installation and application warnings

Firmware notes: This section highlights important information for this specific firmware and will assist in pricing accordingly, as well as bringing awareness to any operational or vehicle limitations.

T-Harness compatible THFON1 Keys required for

programming 2 Keys required for operation 0

The optional Plug & Play THFON1 T-Harness is sold separately. Key2GO is required if only one key is available. You can program the interface without the need for Key2GO if two keys

are present. Keys required to program:

80-Bit Encryption transponder: Requires two (2) keys for programming. Key2GO is NOT compatible. 40-Bit Encryption transponder: Programming can be completed with two (2) keys or with one (1) key if using Key2GO.

(See "Understanding the difference between a Ford 80 & 40 bit" on page 51 for more information) Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic

connector. It is important to check that the fuses are positioned correctly in the module. Refer to the "Fuse selection" section following

each installation type for more information. Refer to the "Vehicle wiring reference chart" following each installation type.

General notes: This section highlights important information for this specific firmware.

[1] The installation of an aftermarket hood pin is ONLY required on vehicles that are NOT equipped with a factory hood pin.[2] The siren is ONLY required when enabling the security features during module flashing.[3] The green wire is ONLY required for starter disable and antigrind applications.[4] Vehicles with install Type 3, 4, 6, 7 & 10 are NOT compatible with optional T-harness THFON1.[5] Connections ONLY required if features do not operate in data.[6] ONLY required if OEM alarm equipped.

Additional parts required (maximum required):

Diode 6A1 x 1A Diodes86 8530

87a

87

1 x Relay

Resistor 100Ω0 x Resistor Fuse 7.5A0 x Fuse


Vehicle application guideThe following table lists the vehicles and features which are compatible with this product. The number assigned to each year allows you to determine which installation type should be used for your vehicle.

Vehicles

20

16

20

15

20

14

20

13

20

12

20

11

20

10

20

09

20

08

PK-Im

mob

ilize

r By

pass

-Dat

a N

o Ke

y Re

q'd

DL-

Arm

Fac

tory

Sec

urity

DL-

Dis

arm

Fac

tory

Sec

urity

DL-

Doo

r Lo

ck C

ontro

l

DL-

Doo

r U

nloc

k

DL-

Trun

k /

Hat

ch R

elea

se

Key2

GO

RS-3

x LO

CK

STA

RT (S

tart

cont

rol u

sing

OEM

Rem

ote)

RS-3

x LO

CK

STO

P (S

top

cont

rol u

sing

OEM

Rem

ote)

RS-R

AP

Shut

Dow

n (R

etai

ned

AC

C P

ower

)

RS-S

mar

tSta

rt

SS-E

ntry

Mon

itorin

g A

LL D

oor

Pins

SS-E

ntry

Mon

itorin

g H

ood

Pin

SS-E

ntry

Mon

itorin

g Tr

unk/

Hat

ch P

in

SS-F

acto

ry A

larm

Trig

ger

Mon

itorin

g

ST-B

rake

Sta

tus

(foot

bra

ke)

ST-D

oor

Lock

s St

atus

ST-E

-Bra

ke S

tatu

s

ST-Ig

nitio

n St

atus

FordCrown Victoria 6 [4] 6 [4] • • • • • • • • • • • • • • • • • • •Edge 1 1 1 1 2 2 2 • • • • • • • • • • • • • • • • • • •Escape 2 2 2 2 2 • • • • • • • • • • • • • • • • • • •Escape Hybrid 2 2 2 2 2 • • • • • • • • • • • • • • • • • • •E-Series 4[4] 4[4] 4[4] 4[4] 4[4] 4[4] 4[4] • • • • • • • • • • • • • • • • •Expedition 3[4] 3[4] 10[4] • • • • • • • • • • • • • • • • • • •Expedition 1 1 3[4] 3[4] 3[4] 3[4] • • • • • • • • • • • • • • • • • •Explorer 1 1 1 1 1 1 1 1 • • • • • • • • • • • • • • • • • • •F-150 3[4] 3[4] 9 • • • • • • • • • • • • • • • • •F-150 1 1 1 1 • • • • • • • • • • • • • • • •F-250 3[4] 3[4] 3[4] • • • • • • • • • • • • • • • • •F-250 1 1 1 1 1 1 • • • • • • • • • • • • • • • •F-350 3[4] 3[4] 3[4] • • • • • • • • • • • • • • • • •F-350 1 1 1 1 1 1 • • • • • • • • • • • • • • • •F-450 3[4] 3[4] 3[4] • • • • • • • • • • • • • • • • •F-450 1 1 1 1 1 1 • • • • • • • • • • • • • • • •Flex 1 1 1 1 1 1 • • • • • • • • • • • • • • • • • •Flex 2 2 • • • • • • • • • • • • • • • • • • •Focus 1 1 1 2 • • • • • • • • • • • • • • • • • • •Fusion 1 1 1 2 2 • • • • • • • • • • • • • • • • • • •Mustang 1 1 2 2 2 7[4] 7[4] • • • • • • • • • • • • • • • • • • •Sport Trac 1 1 1 • • • • • • • • • • • • • • • • •Taurus 1 1 1 1 1 1 1 • • • • • • • • • • • • • • • • • • •Taurus X 8 8 • • • • • • • • • • • • • • • • • • •Transit Connect (with power locks) 1 1 1 1 • • • • • • • • • • • • • • • • •Transit Connect (without power locks) 5 5 5 5 • • • • • • • • • • • • • • • • •Lincoln 16 15 14 13 12 11 10 09 08MKS 2 2 2 2 • • • • • • • • • • • • • • • • • • •MKX 2 2 2 • • • • • • • • • • • • • • • • • • •MKZ 1 1 1 2 2 • • • • • • • • • • • • • • • • • • •Navigator 3[4] 3[4] 3[4] 3[4] 3[4] 3[4] 3[4] • • • • • • • • • • • • • • • • • • •Mercury 16 15 14 13 12 11 10 09 08Grand Marquis 6[4] 6[4] • • • • • • • • • • • • • • • • • • •Mariner 2 2 2 2 • • • • • • • • • • • • • • • • • • •Mariner Hybrid 2 2 2 2 • • • • • • • • • • • • • • • • • • •Milan 1 1 2 2 • • • • • • • • • • • • • • • • • • •Mountaineer 1 1 1 • • • • • • • • • • • • • • • • • • •Sable 2 2 • • • • • • • • • • • • • • • • • • •

DS4+ [4] Vehicles with install Type 3, 4, 6, 7, 8, 9 & 10 are NOT compatible with optional T-Harness THFON1

Legend:DL: OE Door Lock & Alarm Controls PK: Transponder & Immobilizer Override SS: Integrated Security & MonitoringFOB: Sync CAN Interface w/ FOB Remote RS: Remote Start & Engine Controls ST: Function/Feature Status


Wiring connectionsThe wiring connections listed below are specific to this firmware.

Main harness (H1), 12-pin black connector

Conn./Pin Color Description

H1/1 Blue/White Relay 1 N.C. – No Connection 1

H1/2 Blue/Red Relay 1 N.O. – (+) 12V Input 1

H1/3 Blue Relay 1 COM – (+) Ignition Output 1

H1/4 White/Brown Relay 3 N.C. – No Connection 1

H1/5 White Relay 3 COM – (+) Parking Light Output 1

H1/6 Red (+) 12 Volt (Battery)

H1/7 Lt. Green/Red Relay 2 N.O. – (-) Ground 1

H1/8 Lt. Green Relay 2 COM – RAP Off Interrupt or (-) RAP Off Output 1

H1/9 Lt. Green/White Relay 2 N.C. – RAP Off Interrupt 1

H1/10 Black (-) Ground

H1/11 White Relay 3 COM – Parking Light Output 1

H1/12 Red (+) 12 Volt (Battery)

Relay harness (H2), 10-pin white connector


H2/1 N/A No Connection

H2/2 Red/Black No Connection

H2/3 Pink/Black No Connection 1

H2/4 Pink/White No Connection 1

H2/5 Red No Connection

H2/6 Green No Connection 1

H2/7 Violet No Connection 1

H2/8 Orange No Connection 1

H2/9 Red/White No Connection

H2/10 Pink No Connection

Data harness (H3), 8-pin white connector


H3/1 Tan MS CAN Low

H3/2 Tan/Black MS CAN High

H3/3 Orange/Brown HS CAN High

H3/4 Orange/Green HS CAN Low

H3/5 Lt. Green No Connection

H3/6 Violet/Brown No Connection

H3/7 Orange/Black Data RX

H3/8 Yellow/Black Data TX

1. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed.


Analog input/output harness (H4), 22-pin white connector


H4/1 Lt. Green/Black No Connection 1

H4/2 Blue/White (-) Ground When Running (Status) Output 1

H4/3 Dk. Green/Black (-) Lock Output 1

H4/4 Red/White (-) Trunk Release Output 1

H4/5 Brown/Black (-) Horn 1

H4/6 Brown/White N/A

H4/7 White (+) Accessory/Keysense Output 1

H4/8 Violet/Black (+) Starter Output 1

H4/9 Dk. Blue/Black (-) Unlock Output 1

H4/10 Lt. Blue/Black (-) Factory Alarm Disarm 1

H4/11 Brown/Red (+) Siren Output 1

H4/12 Pink (+) Ignition Sense Input

H4/13 Violet (+) Door Input 2

H4/14 Brown (+) Brake Input 2

H4/15 White/Blue (-) Activation (Start Trigger) Input 2

H4/16 Red/Blue No Connection 2

H4/17 Black/White (-) Parking Brake Input (Manual Transmission) 2

H4/18 Orange/Black (-) Instant Alarm Trigger Input 2

H4/19 Blue (-) Trunk Trigger Input 2

H4/20 Green (-) Door Input 2

H4/21 Gray (-) Hood Pin Input 2

H4/22 Violet/White (AC) Tach Input

RF Port harness (H5), 2-pin white connector


H5/1 N/A RF Loop

H5/2 N/A RF Loop

D2D harness (H6), 4-pin white (1) and black (2) connectors


H6/1 Blue (Data) TX

H6/2 Black (-) Ground

H6/3 Green (Data) RX

H6/4 Red (+) 12 Volt

Temperature sensor harness (H7), 2-pin black connector


H7/1 Black Temperature Sensor

H7/2 Black Temperature Sensor

1. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary.

2. These connections are only required if the corresponding statuses are not supported by the firmware. See "Vehicle application guide" on page 5 for a list of compatible features. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary.


Installation (wiring diagrams, fuse selection & vehicle wiring reference charts)Type 1 with T-Harness (THFON1)

Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of each special note referenced in the diagram ( ).

228

1012

42

44

2

DS4+

DS4

Slideto open

Proper FusePositioning

DS4+ DS4

5

15

5

15MAIN (5A) (+)

(-) RLY3/PK LIGHT(15A) (+)

MAIN (5A) (+)


5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

MAIN (5A) (+)

(-) RLY3 PK LIGHT (15A) (+)

(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

It is important to check that the fuses are positioned correctly.

5

15

5

15MAIN (5A) (+)


MAIN (5A) (+)


5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

THFON1(optional T-Harness)

5

15

5

15MAIN (5A) (+)


MAIN (5A) (+)


5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

5MAIN (5A) (+)


5

30

20

20

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

Ignition SwitchConnector

(connector side)

7421 3 5 6

Ignition Barrel7421 3 5 6

P.A.T.S. 4-pin Connector(connector side)

malefemale

OBDIIDiagnostic 16-pin Connector

(-) Lock Output: Green/Black

(-) Trunk Hatch Release/Power Liftgate Output: Red/White

(-) Unlock Output: Blue/Black

(+) Siren Output: Brown/Red

Hood Pin: Gray

(+) Parking Light Output: White

RAP Off Interrupt: Lt. Green

RAP Off Interrupt: Lt. Green/White

Hood PinSiren

Refer to the Vehicle wiring reference charts for wire and connector details related to the standard connections in the vehicle.

Driver Door Trigger

Cut

15

15(AC) Tach Output: Violet/White


Type 1Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of each special note referenced in the diagram ( ).

16

8

9

1

(+) 12V Input: Blue/Red: 2

(+) Ignition Output: Blue: 3

(-) Ground: Black: 10

MS CAN Low: Tan: 1

(-) Trunk Hatch Release/Power Liftgate Output: Red/White: 4

MS CAN High: Tan/Black: 2

HS CAN High: Orange/Green: 4HS CAN Low: Orange/Brown: 3

Data RX: Orange/Black: 7

(+) Parking Light Output: White: 5 & 11

Hood Pin(-) Hood Pin Input: Gray: 21

(AC) Tach Output: Violet/White: 22

Siren(+) Siren Output: Brown/Red: 11

HS CAN Low: Pin 14

HS CAN High: Pin 6

MS CAN Low: Pin 11

MS CAN High: Pin 3


Data TX: Yellow/Black: 8

(-) Lock Output: Dk. Green/Black: 3

(+) Accessory/Keysense Output: White: 7(+) Starter Output: Violet/Black: 8

(-) Unlock Output: Dk. Blue/Black: 9

Driver Door TriggerRAP Off Interrupt: Lt. Green: 8

RAP Off Interrupt: Lt. Green/White: 9

(+) 12V Input: Red: 6 & 12

P.A.T.S. - 4-pin(at ignition switch)

1

2

3

4RX: Pin 4

TX: Pin 3

228

1012

42

44

2

DS4+

DS4

Slideto open


DS4+ DS4


MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


5

30

20

20

5

15

15

Cut

(+) 12V: Pin 4

(+) Start: Pin 7

(+) Ignition: Pin 1

Ignition Switch(black conn. at ign. switch)

(+) Keysense: Pin 5

(+) Accessory: Pin 6

1A Diode

1 2 3 4 5 6 7

OBDII Diagnostic (connector side view)


Vehicle wiring reference chartThis section provides vehicle wiring information to guide you through the various stages of your installation. Refer to www.directechs.com for additional information.

Wire Information Connector Information

Function Color Pin Polarity Location Color Pins Ref.

Ford Edge 2011-2014

RX Violet/Gray 4 Data (PATS) connector. Black 4 A

TX Yellow/Orange 3 Data (PATS) connector. Black 4 A

Power Liftgate Gray/Yellow 6 (-) Power liftgate switch. Black 6 F

12V Green/Red 4 (+) Ignition switch. Black 7 B

Starter Blue/White 7 (+) Ignition switch. Black 7 B

Ignition White/Orange 1 (+) Ignition switch. Black 7 B

Accessory Violet/Green 6 (+) Ignition switch. Black 7 B

Keysense Blue/Gray 5 (+) Ignition switch. Black 7 B

Parking Lights Yellow/Blue 6 (+) BCM in drivers kick panel. Gray 10 E

HS CAN High White/Blue 6 Data OBDII. Black 16 C

HS CAN Low White 14 Data OBDII. Black 16 C

MS CAN High Gray/Orange 3 Data OBDII. Black 16 C

MS CAN Low Violet/Orange 11 Data OBDII. Black 16 C

Driver Door Trigger Green/Violet 9 Cut BCM in drivers kick panel. Black 26 D

Lock Blue/Green 6 (-) BCM in drivers kick panel. Black 26 D

Unlock Yellow/Violet 8 (-) BCM in drivers kick panel. Black 26 D

Tach Green/Blue, Gray/Yellow, Violet/Gray, Yellow/Orange, Brown or Green/White

1 (AC) Any fuel injector. Black 2 N/A

http://www.directechs.com




Ford Explorer 2008-2010



12V Violet/Red 4 (+) Ignition switch. Black 7 B









Parking Lights Blue/White 11 (+) Fuse/SJB under drivers dash. Brown 32 H

Driver Door Trigger Green/Violet 17 Cut Fuse/SJB (Smart Junction Box) under drivers dash.

Black 32 G

Lock Gray/Yellow 27 (-) Fuse/SJB under drivers dash. Black 32 G

Unlock Yellow/Violet 8 (-) Fuse/SJB under drivers dash. Black 32 G

Tach Not Violet N/A (AC) Any fuel injector. N/A N/A N/A

Ford Explorer 2011-2015

RX Violet/Red or Violet 4 Data (PATS) connector. Black 4 A

TX Yellow/Orange or Yellow 3 Data (PATS) connector. Black 4 A







Parking Lights Yellow/Blue 6 (+) BCM under drivers dash. Gray 10 H





Driver Door Trigger Green/Violet 9 Cut BCM under drivers dash. Black 26 G

Lock Blue/Green 6 (-) BCM under drivers dash. Black 26 G

Unlock Yellow/Violet 8 (-) BCM under drivers dash. Black 26 G

Tach Green/Blue, Gray/Yellow, Violet/Gray, Yellow/Orange, Brown or Green/White





Ford F150 2011-2014








Parking Lights Yellow/Blue 6 (+) BCM in passenger kick panel. Gray 10 J





Driver Door Trigger Green/Violet 9 Cut BCM (Body Control Module) in passenger kick panel.

Black 26 I

Lock Blue/Green 6 (-) BCM in passenger kick panel. Black 26 I

Unlock Yellow/Violet 8 (-) BCM in passenger kick panel. Black 26 I

Tach Green/Blue, Gray/Yellow, Violet/Gray, Yellow/Orange, Brown, Green/White, Gray/Brown or Violet/Orange

1 (AC) Any fuel injector. Gray 2 N/A

Ford F250 2011-2016

RX Yellow/Orange 4 Data (PATS) connector. Black 4 A

TX Violet/Gray 3 Data (PATS) connector. Black 4 A

12V Blue/Red or Green/Red 4 (+) Ignition switch. Black 7 B





Parking Lights Yellow/Blue 6 (+) SJB (Smart Junction Box) passenger kick panel.

Gray 10 J





Driver Door Trigger Green/Violet 9 Cut SJB passenger kick panel. Black 26 I

Lock Blue/Green 6 (-) SJB passenger kick panel. Black 26 I

Unlock Yellow/Violet 8 (-) SJB passenger kick panel. Black 26 I

Tach Blue N/A (AC) Customer Access Harness above driver kick, taped to wiring harness. On models without the Customer Access Harness, go to any fuel injector and use the wire that is not blue (gasoline), or use the camshaft position sensor, which is white/green at the Powertrain Control Module on passenger side of engine, middle, black 98 pin plug, pin 32 (diesel).

Gray 2 N/A




Ford F350 2011-2016









Gray 10 J









Gray 2 N/A

Ford F450 2011-2016









Gray 10 J









Gray 2 N/A




Ford Flex 2011-2012



12V Blue/Red 4 (+) Ignition switch. Black 7 B





Parking Lights Violet/White 6 (+) SJB (Smart Junction Box) under drivers dash.

Gray 13 H





Driver Door Trigger Green/Violet 14 Cut SJB under drivers dash. Gray 26 G

Lock Blue/Green 17 (-) SJB under drivers dash. Gray 26 G

Unlock Yellow/Violet 4 (-) SJB under drivers dash. Gray 26 G

Power Liftgate Gray/Yellow N/A (-) Drivers kick panel harness to rear. N/A N/A K



Ford Flex 2013-2016

RX Violet 4 Data (PATS) connector. Black 4 A

TX Yellow 3 Data (PATS) connector. Black 4 A

Power Liftgate Gray 6 (-) Power liftgate switch. Brown 6 F

12V Yellow/Red 4 (+) Ignition switch. Black 7 B



Accessory Violet 6 (+) Ignition switch. Black 7 B

Keysense Blue 5 (+) Ignition switch. Black 7 B

Parking Lights Yellow/Blue 6 (+) BCM (Body Control Module) under drivers dash.

Gray 10 H





Driver Door Trigger Violet 9 Cut BCM under drivers dash. Black 26 G

Lock Blue 6 (-) BCM under drivers dash. Black 26 G

Unlock Yellow 8 (-) BCM under drivers dash. Black 26 G






Ford Focus 2009-2011



12V Brown/Red 4 (+) Ignition switch. Black 7 B


Ignition White/Orange or Brown/Yellow

1 (+) Ignition switch. Black 7 B



Parking Lights Violet/White 6 (+) SJB (Smart Junction Box) under drivers dash.

Gray 13 H






Trunk/Hatch Release Brown/Yellow 20 (-) SJB under drivers dash. Gray 26 G

Lock Gray/Yellow 17 (-) SJB under drivers dash. Gray 26 G

Unlock Violet/Gray 4 (-) SJB under drivers dash. Gray 26 G

Tach Green/Blue, Gray/Yellow, Violet/Gray, Yellow/Orange


Ford Fusion 2010-2012



12V Brown/Red or Blue/Red 4 (+) Ignition switch. Black 7 B





Parking Lights Violet/White 6 (+) Fuse/SJB (Smart Junction Box) under drivers dash.

Gray 13 H





Driver Door Trigger Green/Violet 14 Cut Fuse/SJB under drivers dash. Gray 26 G

Trunk/Hatch Release Brown/Yellow 20 (-) Fuse/SJB under drivers dash. Gray 26 G

Lock Gray/Yellow or Blue/Green 17 (-) Fuse/SJB under drivers dash. Gray 26 G

Unlock Violet/Gray or Yellow/Violet

4 (-) Fuse/SJB under drivers dash. Gray 26 G


1 (AC) Any fuel injector. N/A 2 N/A




Ford Mustang 2013-2014



12V Lt. Green/Violet or Blue/Red



Ignition Gray/Violet 1 (+) Ignition switch. Black 7 B



Parking Lights Violet/White 6 (+) SJB (Smart Junction Box) in passenger kick panel.

Gray 13 J





Driver Door Trigger Green/Violet 14 Cut SJB in passenger kick panel. Gray 26 I

Lock Blue/Green 17 (-) SJB in passenger kick panel. Gray 26 I

Unlock Yellow/Violet 4 (-) SJB in passenger kick panel. Gray 26 I

Trunk/Hatch Release Brown/Yellow (Coupe); Brown/Yellow or Brown/Violet (Convertible)

20 (-) SJB in passenger kick panel. Gray 26 I


1 (AC) Any fuel injector. Gray or Black 2 N/A

Ford Sport Trac 2008-2010













Black 32 G

Lock Gray/Yellow 6 (-) Fuse/SJB under drivers dash. Black 32 G

Unlock Yellow/Violet 8 (-) Fuse/SJB under drivers dash. Black 32 G

Tach NOT Violet N/A (AC) Any fuel injector. N/A N/A N/A




Ford Taurus 2008-2009



12V Red 4 (+) Ignition switch. Black 7 B






Gray 13 H






Gray 26 G

Lock Blue/Green 17 (-) Fuse/SJB under drivers dash. Gray 26 G

Unlock Yellow/Violet 4 (-) Fuse/SJB under drivers dash. Gray 26 G

Trunk/Hatch Release Brown 20 (-) Fuse/SJB under drivers dash. Gray 26 G

Tach Green/Blue, Gray/Yellow, Violet/Gray, Yellow/Orange, Brown, Green/White











Gray 13 H








Trunk/Hatch Release Brown or Brown/Yellow 20 (-) Fuse/SJB under drivers dash. Gray 26 G

Parking Lights Blue/White 11 (+) Fuse/SJB under drivers dash. Brown 32 H


1 (AC) Any fuel injector. Gray or Black 2 N/A







Trunk/Hatch Release Brown or Brown/Yellow 2 (-) Trunk release switch. Black 2 F





Parking Lights Yellow/Blue 6 (+) BCM (Body Control Module) under drivers dash.

Gray 10 H





Driver Door Trigger Green/Violet 9 Cut BCM under drivers dash. Black 26 G

Lock Blue/Green 6 (-) BCM under drivers dash. Black 26 G

Unlock Yellow/Violet 8 (-) BCM under drivers dash. Black 26 G

12V Red 6 (+) BCM under drivers dash. White 32 H


1 (AC) Any fuel injector. White 2 N/A

Ford Transit Connect (with power locks) 2010-2013

RX White/Lt. Green 4 Data (PATS) connector. Black 4 A

TX Gray/Orange 3 Data (PATS) connector. Black 4 A


Starter Gray/Black or Orange/Black


Ignition Green/Yellow 1 (+) Ignition switch. Black 7 B

Accessory Yellow 6 (+) Ignition switch. Black 7 B

Keysense Black/Red 5 (+) Ignition switch. Black 7 B

Parking Lights Orange/Yellow 13 (+) Headlight switch. Black 16 F

HS CAN High Gray/Red 6 Data OBDII. Black 16 C

HS CAN Low Blue/Red 14 Data OBDII. Black 16 C


MS CAN Low Blue/Black 11 Data OBDII. Black 16 C

Driver Door Trigger Black/Yellow 18 (-) GEM (Generic Electronic Module) behind dash fuse box.

Gray 23 G

Lock Black/Orange 10 (-) GEM behind dash fuse box. Green 23 H

Unlock Black/Green 11 (-) GEM behind dash fuse box. Green 23 H






Lincoln MKZ 2010-2012









Gray 13 H






Lock Gray/Yellow or Blue/Green 17 (-) Fuse/SJB under drivers dash. Gray 26 G



Trunk/Hatch Release Gray/Yellow or Brown/Yellow




Mercury Milan 2010-2011









Gray 13 H








Trunk/Hatch Release Brown/Yellow 20 (-) Fuse/SJB under drivers dash. Gray 26 G






Mercury Mountaineer 2008-2010












Parking Lights Blue/White 11 (+) Fuse/SJB (Smart Junction Box) under drivers dash.

Brown 32 G

Driver Door Trigger Green/Violet 17 Cut Fuse/SJB under drivers dash. Black 32 H

Lock Gray/Yellow 27 (-) Fuse/SJB under drivers dash. Black 32 H

Unlock Violet/Gray 26 (-) Fuse/SJB under drivers dash. Black 32 H

Trunk/Hatch Release Brown 29 (-) Fuse/SJB under drivers dash. Black 32 H

Tach NOT Violet N/A (AC) Any fuel injector. N/A N/A N/A


Type 2 with T-Harness (THFON1)Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of each special note referenced in the diagram ( ).

228

1012

42

44

2

DS4+

DS4

Slideto open


DS4+ DS4

5

15

5

15MAIN (5A) (+)


MAIN (5A) (+)


5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)


5

15

5

15MAIN (5A) (+)


MAIN (5A) (+)


5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)


5

15

5

15MAIN (5A) (+)


MAIN (5A) (+)


5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

5MAIN (5A) (+)


5

30

20

20

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)


(connector side)

7421 3 5 6



malefemale


15

15

(-) Lock Output: Green/Black

(-) Trunk Hatch Release/Power Liftgate Output: Red/White

(-) Unlock Output: Blue/Black


Hood Pin: Gray


RAP Off Interrupt: Lt. Green

RAP Off Interrupt: Lt. Green/White

Hood PinSiren


Driver Door Trigger

Cut

(AC) Tach Output: Violet/White



16

8

9

1



MS CAN Low: Tan: 1

(-) Trunk Hatch Release/Power Liftgate Output: Red/White: 4





HS CAN Low: Pin 14

HS CAN High: Pin 6

MS CAN Low: Pin 11

MS CAN High: Pin 3




(+) Accessory Output: White: 7(+) Starter Output: Violet/Black: 8



1

2

3

4RX: Pin 4

TX: Pin 3

228

1012

42

44

2

DS4+

DS4

Slideto open


DS4+ DS4


MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


5

30

20

20

5

15

15

(+) 12V: Pin 4

(+) Start: Pin 7

(+) Ignition: Pin 1



1 2 3 4 5 6 7


Driver Door TriggerRAP Off Interrupt: Lt. Green: 8

RAP Off Interrupt: Lt. Green/White: 9Cut

(+) 12V Input: Red: 6 & 12

(-) Factory Alarm Disarm Output: Lk. Blue/Black: 10

HoodPin (-) Hood Pin Input: Gray: 21

(AC) Tach Output: Violet/White: 22Siren

(+) Siren Output: Brown/Red: 11






Ford Edge 2008-2010











Driver Door Trigger Green/Violet 14 Cut Fuse/SJB (Smart Junction Box) under drivers dash. Gray 26 D

Factory Alarm Disarm Violet/Brown 8 (-) Fuse/SJB under drivers dash. Gray 26 D

Parking Lights Violet/White 20 (+) Fuse/SJB under drivers dash. Black 32 E







Ford Escape 2008-2012

RX Violet/Gray 4 or 3

Data (PATS) connector. Black 4 A

TX Yellow/Orange 3 or 4










Driver Door Trigger Green/Violet 14 Cut SJB (Smart Junction Box) passenger side of the center console. Gray 26 F

Trunk/Hatch Release Brown 7 (+) SJB passenger side of the center console. Gray 26 F

Lock Blue/Green 17 (-) SJB passenger side of the center console. Gray 26 F

Unlock Yellow/Violet 4 (-) SJB passenger side of the center console. Gray 26 F

Parking Lights Violet/White 20 (+) SJB passenger side of the center console. Black 32 G

Factory Alarm Disarm Violet/Brown N/A (-) Drivers kick panel, door harness. N/A N/A H



Ford Escape Hybrid 2008-2012

RX Violet/Gray 4 or 3


TX Yellow/Orange 3 or 4





















Ford Flex 2009-2010







Parking Lights Violet/White 6 (+) SJB (Smart Junction Box) passenger side of the center console. Gray 13 G




MS CAN Low Violet/Orange 11 Data OBDII. Black 16 F

Driver Door Trigger Green/Violet 14 Cut SJB passenger side of the center console. Gray 26 F




Factory Alarm Disarm Green/Violet 8 (-) SJB passenger side of the center console. Gray 26 F



Ford Focus 2008







Parking Lights Violet/White 6 (+) SJB (Smart Junction Box) under drivers dash. Gray 13 E





Driver Door Trigger Green/Violet 14 Cut SJB (Smart Junction Box) under drivers dash. Gray 26 D

Trunk/Hatch Release Brown 20 (-) SJB under drivers dash. Gray 26 D

Lock Blue/Green 17 (-) SJB under drivers dash. Gray 26 D

Unlock Yellow/Violet 4 (-) SJB under drivers dash. Gray 26 D

Factory Alarm Disarm Violet/Brown 8 (-) SJB under drivers dash. Gray 26 D






Ford Fusion 2008-2009



Trunk/Hatch Release Brown 5 (-) Trunk release switch. Black 6 I









Parking Lights Gray/Yellow 31 (+) Fuse/SJB (Smart Junction Box) under drivers dash. Brown 32 D

Driver Door Trigger Green/Violet 11 Cut Fuse/SJB under drivers dash. Black 32 D

Lock Gray/Yellow 4 (-) Fuse/SJB under drivers dash. Black 32 D

Unlock Violet/Gray 10 (-) Fuse/SJB under drivers dash. Black 32 D

Factory Alarm Disarm Violet/Brown 5 (-) Fuse/SJB under drivers dash. Black 32 D

Tach NOT Violet N/A (AC) NOT White/Blue (2.3L, 3.0L), NOT Violet/Green (3.5L) N/A N/A N/A




12V Lt. Green/Violet or Blue/Red





Parking Lights Violet/White 6 (+) SJB (Smart Junction Box) in passenger kick panel. Gray 13 K





Driver Door Trigger Green/Violet 14 Cut SJB in passenger kick panel. Gray 26 J

Lock Blue/Green 17 (-) SJB in passenger kick panel. Gray 26 J

Unlock Yellow/Violet 4 (-) SJB in passenger kick panel. Gray 26 J

Trunk/Hatch Release Brown/Yellow (Coupe); Brown/Yellow or Brown/Violet (Convertible)

20 (-) SJB in passenger kick panel. Gray 26 J

Factory Alarm Disarm Green/Violet 8 (-) SJB in passenger kick panel. Gray 26 J


1 (AC) Any fuel injector. Gray or Black

2 N/A




Lincoln MKS 2009-2012







Factory Alarm Disarm Green/Violet 12 (-) DDM (Drivers Door Module) in drivers door. Gray 12 L

Parking Lights Violet/White 6 (+) Fuse/SJB (Smart Junction Box) under drivers dash. Gray 13 E





Driver Door Trigger Green/Violet 14 Cut Fuse/SJB under drivers dash. Gray 26 D

Lock Gray/Yellow or Blue/Green

17 (-) Fuse/SJB under drivers dash. Gray 26 D



Trunk/Hatch Release Gray/Yellow or Brown/Yellow




2 N/A

Lincoln MKX 2008-2010



Power Liftgate Gray/Yellow 5 (-) Power liftgate switch. Black 6 I









Driver Door Trigger Green/Violet 14 Cut Fuse/SJB (Smart Junction Box) under drivers dash. Gray 26 D

Lock Gray/Yellow 17 (-) Fuse/SJB under drivers dash. Gray 26 D

Unlock Violet/Gray 4 (-) Fuse/SJB under drivers dash. Gray 26 D

Factory Alarm Disarm Green/Violet 8 (-) Fuse/SJB under drivers dash. Gray 26 D

Parking Lights Violet/White 30 (+) Fuse/SJB under drivers dash. Black 32 D



2 N/A




Lincoln MKZ 2008-2009



12V Blue/Red or Brown/Red









Parking Lights Gray/Yellow 31 (+) Fuse/SJB (Smart Junction Box) under drivers dash. Brown 32 E

Driver Door Trigger Green/Violet 11 Cut Fuse/SJB under drivers dash. Black 32 D

Lock Gray/Yellow or Blue/Green

4 (-) Fuse/SJB under drivers dash. Black 32 D


10 (-) Fuse/SJB under drivers dash. Black 32 D

Factory Alarm Disarm Violet/Brown 5 (-) Fuse/SJB under drivers dash. Black 32 D

Trunk/Hatch Release Brown 27 (-) Fuse/SJB under drivers dash. Black 32 D

Tach NOT white/blue (2.3L, 3.0L), NOT violet/grn (3.5L)

N/A (AC) Any fuel injector. N/A N/A N/A

Mercury Mariner 2008-2011






















Mercury Mariner Hybrid 2008-2011



















Mercury Milan 2008-2009



Trunk/Hatch Release Brown 5 (-) Trunk release switch. Black 6 I









Parking Lights Gray/Yellow 31 (+) Fuse/SJB (Smart Junction Box) under drivers dash. Brown 32 F

Driver Door Trigger Green/Violet 11 Cut Fuse/SJB) under drivers dash. Black 32 F

Lock Gray/Yellow 4 (-) Fuse/SJB) under drivers dash. Black 32 F

Unlock Violet/Gray 10 (-) Fuse/SJB) under drivers dash. Black 32 F

Factory Alarm Disarm Violet/Brown 5 (-) Fuse/SJB) under drivers dash. Black 32 F

Tach NOT white/blue (2.3L, 3.0L), NOT violet/grn (3.5L)





Mercury Sable 2008-2009







Parking Lights Violet/White 6 (+) SJB (Smart Junction Box) under drivers dash. Gray 13 H






Lock Blue/Green 17 (-) SJB under drivers dash. Gray 26 G

Unlock Yellow/Violet 4 (-) SJB under drivers dash. Gray 26 G

Factory Alarm Disarm Green/Violet 8 (-) SJB under drivers dash. Gray 26 G




Type 3 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of each special note referenced in the diagram ( ).

Ignition Switch(gray conn. at ign. switch)

6 1087 9

1 532 4

16

8

9

1



MS CAN Low: Tan: 1

(-) Power Liftgate Output: Red/White: 4





HS CAN Low: Pin 14

HS CAN High: Pin 6

MS CAN Low:Pin 11

MS CAN High:Pin 3




(+) Accessory/Keysense Output: White: 7(+) Starter Output: Violet/Black: 8



1

2

3

4RX: Pin 4

TX: Pin 3

228

1012

42

44

2

DS4+

DS4

Slideto open


DS4+ DS4


MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


5

30

20

20

5

15

15

(+) 12V: Pin 9

(+) Start: Pin 10

(+) Ignition: Pin 1

(+) Keysense: Pin 3


6A Diode


Driver Door Trigger

RAP Off Interrupt: Lt. Green: 8

RAP Off Interrupt: Lt. Green/White: 9Cut

(+) 12V Input: Red: 6 & 12


(AC) Tach Output: Violet/White: 22Siren

(+) Siren Output: Brown/Red: 11






Ford Expedition 2009-2014

RX Blue/Gray 4 Data (PATS) connector. Black 4 A

TX Violet/Brown 3 Data (PATS) connector. Black 4 A


12V Blue/Red 9 (+) Ignition switch. Gray 10 B

Starter Blue/White 10 (+) Ignition switch. Gray 10 B

Ignition White/Orange 1 (+) Ignition switch. Gray 10 B

Accessory Brown/Yellow 7 (+) Ignition switch. Gray 10 B

Keysense Blue/Gray 3 (+) Ignition switch. Gray 10 B

Parking Lights Violet/White 6 (+) SJB (Smart Junction Box) passenger kick panel. Gray 13 E





Driver Door Trigger Green/Violet 14 Cut SJB passenger kick panel. Gray 26 D

Lock Gray/Yellow 17 (-) SJB passenger kick panel. Gray 26 D

Unlock Violrt/Gray 4 (-) SJB passenger kick panel. Gray 26 D

Tach NOT B lue N/A (AC) Any fuel injector. N/A N/A N/A

Ford F150 2009-2010



12V Violet/Red 9 (+) Ignition switch. Gray 10 B



Accessory Violet/Green 5 (+) Ignition switch. Gray 10 B


Parking Lights Violet/White 6 (+) SJB (Smart Junction Box) in passenger kick panel. Gray 13 E





Driver Door Trigger Green/Violet 14 Cut SJB in passenger kick panel. Gray 26 D

Lock White/Brown 17 (-) SJB passenger kick panel. Gray 26 D

Unlock Blue/Brown 4 (-) SJB passenger kick panel. Gray 26 D

Tach Blue N/A (AC) Customer Access Harness behind data link connector. N/A N/A N/A





Ford F250 2008-2010



12V Blue/Red or White/Violet

9 (+) Ignition switch. Gray 10 B



Accessory Brown/Yellow or Yellow/Orange









Lock Blue/Green 17 (-) SJB passenger kick panel. Gray 26 D

Unlock Yellow/Violet 4 (-) SJB passenger kick panel. Gray 26 D


Ford F350 2008-2010











HS CAN High White/Blue or White/Lt. Green

6 Data OBDII. Black 16 C

HS CAN Low White or Pink/Lt. Green











Ford F450 2008-2010











HS CAN High White/Lt. Green or White/Blue


HS CAN Low Pink/Lt. Green or White








Lincoln Navigator 2008-2014

RX Yellow/Orange or Blue/Gray

4 Data (PATS) connector. Black 4 A

TX Violet/Gray or Violet/Brown

3 Data (PATS) connector. Black 4 A





Accessory Brown/Yellow 7 (+) Ignition switch. Gray 10 B


Parking Lights Violet/White 6 (+) SJB (Smart Junction Box) in passenger kick panel. Gray 13 E





Driver Door Trigger Green/Violet 14 Cut SJB in passenger kick panel. Gray 26 D

Lock White/Brown 17 (-) SJB in passenger kick panel. Gray 26 D

Unlock Blue/Brown 4 (-) SJB in passenger kick panel. Gray 26 D

Tach NOT B lue N/A (AC) Any fuel injector. N/A N/A N/A



16

8

9

1


MS CAN Low: Tan: 1MS CAN High: Tan/Black: 2





Siren (+) Siren Output: Brown/Red: 11

HS CAN Low: Pin 14

HS CAN High: Pin 6

MS CAN Low:Pin 11

MS CAN High:Pin 3

Refer to the Vehicle wiring reference

charts for wire and connector details related to the standard connections in the vehicle.




(-) Driver Door Trigger(-) RAP Off Output: Lt. Green: 8

(-) Ground: Lt. Green/Red: 7

(+) 12V Input: Red: 6 & 12


1

2

3

4RX: Pin 4

TX: Pin 3

228

1012

42

44

2

DS4+

DS4

Slideto open


DS4+ DS4


MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


5

30

20

20

5

15

15

Ignition Switch(gray and black connector

at ignition switch)

(+) Accessory 2: Pin 3

(+) 12V: Pin 2

(+) Ignition: Pin 1


(+) Starter: Pin 5

9 10 11 12 13

7641

8

532

(+) Ignition Input/Ouput: Pink: 10(+) Accessory 1 Output: Orange: 8

(+) 12V Input: Red/Black: 2

(+) Starter Output (veh. side): Violet: 7

(+) Accessory 2: Pink/White: 4

Starter Input (Key Side): Green: 6

(+) 12V Input: Red: 5







Ford E-Series 2008

RX Gray/Orange 3 Data (PATS) connector. N/A 4 A

TX White/Lt. Green 4 Data (PATS) connector. N/A 4 A

12V Lt. Green/Violet 2 (+) Ignition switch. Gray or Black

13 B

Starter White/Pink 5 (+) Ignition switch. Gray or Black

13 B

Ignition Pink/Lt. Green 1 (+) Ignition switch. Gray or Black

13 B

Accessory 1 Gray/Yellow 8 (+) Ignition switch. Gray or Black

13 B

Accessory 2 Black/Lt. Green 3 (+) Ignition switch. Gray or Black

13 B

HS CAN High White/Lt. Green 6 Data OBDII. Black 16 C

HS CAN Low Pink/Lt. Green 14 Data OBDII. Black 16 C

MS CAN High White/Black 3 Data OBDII. Black 16 C

MS CAN Low Black/Yellow 11 Data OBDII. Black 16 C

Parking Lights Brown N/A (+) Drivers kick panel harness to rear. N/A N/A D

Driver Door Trigger Red/Pink N/A (-) Drivers kick panel. N/A N/A E

Lock (with keyless entry) Orange/Black or Red N/A (-) Drivers kick panel door harness. N/A N/A E

Unlock (with keyless entry) Yellow/Red or Brown N/A (-) Drivers kick panel door harness. N/A N/A E

Lock (without keyless entry) Pink/Yellow N/A 5-wire Drivers kick panel door harness. N/A N/A E

Unlock (without keyless entry)

Pink/Lt. Green N/A 5-wire Drivers kick panel door harness. N/A N/A E

Tach White/Pink N/A (AC) "Customer Access Harness is around the middle of the main harness that runs along the top of the firewall, under the hood."

N/A N/A N/A





Ford E-Series 2009-2014

RX Violet/Gray 3 Data (PATS) connector. Green 4 A

TX Yellow/Orange 4 Data (PATS) connector. Green 4 A

12V Blue/Red 2 (+) Ignition switch. Gray or Black

13 B

Starter Blue/White 5 (+) Ignition switch. Gray or Black

13 B

Ignition White/Orange 1 (+) Ignition switch. Gray or Black

13 B

Accessory 1 Brown/Yellow 8 (+) Ignition switch. Gray or Black

13 B

Accessory 2 Violet/Green 3 (+) Ignition switch. Gray or Black

13 B

Parking Lights Violet/White 6 (+) SJB (Smart Junction Box) under drivers dash. Gray 13 F





Driver Door Trigger Green/Violet 14 (-) SJB under drivers dash. Gray 26 G

Lock Gray/Yellow 17 (-) SJB under drivers dash. Gray 26 G

Unlock Violet/Gray 4 (-) SJB under drivers dash. Gray 26 G

Tach White/Pink N/A (AC) "Customer Access Harness is around the middle of the main harness that runs along the top of the firewall, under the hood."

N/A N/A N/A


Type 5 with T-Harness (THFON1)Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of each special note referenced in the diagram ( ).

228

1012

42

44

2

DS4+

DS4

Slideto open


DS4+ DS4

5

15

5

15MAIN (5A) (+)


MAIN (5A) (+)


5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)


5

15

5

15MAIN (5A) (+)


MAIN (5A) (+)


5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)


5

15

5

15MAIN (5A) (+)


MAIN (5A) (+)


5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

5

15

30

20

20

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

5MAIN (5A) (+)


5

30

20

20

MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)


(connector side)

7421 3 5 6



malefemale


Hood Pin: Gray


(-) RAP Off Output: Lt. Green


Hood Pin

Siren

(+) Parking Lights: Orange/Yellow: pin 13

1 2

9 10

3 4

11 12

5 7

13 14

8 9

15 16

Headlight Switch(black conn. at headlight switch)

(-) Driver Door Trigger: Black/Yellow: pin 18

1 2 3 4 5

7610 11 12 1398

19 20 21 22 231514 1716 18

General Electronic Module(gray connector behind dash fusebox)

15

15

(-) Ground: Brown/Red

Refer to the Vehicle wiring

reference charts for wire and

connector details related to the

standard connections in

the vehicle.

(AC) Tach Output: Violet/White



16

8

9

1




MS CAN Low: Tan: 1MS CAN High: Tan/Black: 2






HS CAN Low: pin 14

HS CAN High: pin 6

MS CAN Low:pin 11

MS CAN High:pin 3


(+) Accessory Output: White: 7

(+) Starter Output: Violet/Black: 8

(-) RAP Off Output: Lt. Green: 8


(+) 12V Input: Red: 6 & 12


1

2

3

4RX: pin 4

TX: pin 3

228

1012

42

44

2

DS4+

DS4

Slideto open


DS4+ DS4


MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


5

30

20

20

5

15

15

(+) 12V: Red, pin 4

(+) Start: Gray/Black or Orange/Black, pin 7

(+) Ignition: Green/Yellow, pin 1


(+) Accessory: Yellow, pin 6

1 2 3 4 5 6 7

(+) Parking Lights:Orange/Yellow: pin 13

1 2

9 10

3 4

11 12

5 7

13 14

8 9

15 16

Headlight Switch(black conn. at headlight switch)

(-) Driver Door Trigger: Black/Yellow: pin 18

1 2 3 4 5

7610 11 12 1398

19 20 21 22 231514 1716 18

General Electronic Module(gray connector behind dash fusebox)

Refer to the Vehicle wiring reference charts for wire

and connector details related to the standard connections in the vehicle.







Ford Transit Connect (without power locks) 2010-2013

12V - With T-harness Red 2 Data Drivers dash fuse box. White 2 F

RX White/Lt. Green 4 Data (PATS) connector. Black 4 A

TX Gray/Orange 3 Data (PATS) connector. Black 4 A

12V - Without T-harness Red 4 (+) Ignition switch. Black 7 B

Starter Gray/Black or Orange/Black


Ignition Green/Yellow 1 (+) Ignition switch. Black 7 B

Accessory Yellow 6 (+) Ignition switch. Black 7 B

Parking Lights Orange/Yellow 13 (+) Headlight switch. Black 16 D

HS CAN High Gray/Red 6 Data OBDII. Black 16 C

HS CAN Low Blue/Red 14 Data OBDII. Black 16 C


MS CAN Low Blue/Black 11 Data OBDII. Black 16 C

Driver Door Trigger Black/Yellow 18 (-) GEM (Generic Electronic Module) behind dash fuse box. Gray 23 E

Tach NOT White/Red N/A (AC) Any fuel injector. N/A N/A N/A




106

1 5

8

3

7

2

9

4

16

8

9

1

MS CAN Low: Tan: 1

(-) Trunk Release Output: Red/White: 4





HS CAN Low: Pin 14

HS CAN High: Pin 6

MS CAN Low:Pin 11

MS CAN High:Pin 3






OBDII Diagnostic Connector,under Driver Dash (connector side view)


1

2

3

4RX: Pin 4 TX: Pin 3

228

1012

42

44

2

DS4+

DS4

Slideto open


DS4+ DS4


MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


5

30

20

20

5

15

15


at ignition switch)

(+) Accessory 2:White/Violet, pin 3

(+) 12V: Pin 2

(+) Ignition: Violet/Orange,

pin 1

(+) Accessory 1: Gray/Yellow, pin 8

(+) Starter: Dk.Green, pin 5




(+) 12V Input: Red: 6 & 12

(+) Ignition Input/Ouput: Pink: 10(+) Accessory 1 Output: Orange: 8



(+) Accessory 2: Pink/White: 4

Starter Input (Key Side): Green: 6









Ford Crown Victoria 2010-2011

RX Gray/Orange 4 Data (PATS) connector. Black 4 A

TX White/Lt. Green 3 Data (PATS) connector. Black 4 A

12V Lt. Green/Violet 9 (+) Ignition switch. Gray 10 B

Starter Dark Green 10 (+) Ignition switch. Gray 10 B

Ignition Violet/Orange 1 (+) Ignition switch. Gray 10 B

Accessory 1 Gray/Yellow 7 (+) Ignition switch. Gray 10 B

Accessory 2 White/Violet 5 (+) Ignition switch. Gray 10 B

Parking Lights Brown 10 (+) LCM (Lighting Control Module) right of steering column. Black 13 D



MS CAN High Tan/Orange 2 Data OBDII. Black 16 C

MS CAN Low Pink/Lt. Blue 10 Data OBDII. Black 16 C

Driver Door Trigger Dk. Blue 22 (-) DDM (Drivers Door Module) in drivers door. Black 26 E

Trunk Release White/Violet 12 (+) DDM in drivers door. Black 26 E

Lock Pink/Yellow N/A (-) Drivers kick panel door harness. N/A N/A F

Unlock Pink/Lt. Green N/A (-) Drivers kick panel door harness. N/A N/A F


Mercury Grand Marquis 2010-2011



12V Lt. Green/Violet 9 (+) Ignition switch. Gray 10 B

Starter Dark Green 10 (+) Ignition switch. Gray 10 B

Ignition Violet/Orange 1 (+) Ignition switch. Gray 10 B

Accessory 1 Gray/Yellow 7 (+) Ignition switch. Gray 10 B

Accessory 2 White/Violet 5 (+) Ignition switch. Gray 10 B

Parking Lights Brown 10 (+) LCM (Lighting Control Module) right of steering column. Black 13 D



MS CAN High Tan/Orange 2 Data OBDII. Black 16 C

MS CAN Low Pink/Lt. Blue 10 Data OBDII. Black 16 C

Driver Door Trigger Dk. Blue 22 (-) DDM (Drivers Door Module) in drivers door. Black 26 E

Trunk Release White/Violet 12 (+) DDM in drivers door. Black 26 E

Lock Pink/Yellow N/A (-) Drivers kick panel door harness. N/A N/A F

Unlock Pink/Lt. Green N/A (-) Drivers kick panel door harness. N/A N/A F





16

8

9

1


MS CAN Low: Tan: 1

(-) Trunk Release Output: Red/White: 4





HS CAN Low: pin 14

HS CAN High: pin 6

MS CAN Low:pin 11

MS CAN High:pin 3




(-) Unlock:Yellow/Red,pin 5 Driver

Door Trigger:Lt.Green/Black, pin2

(-) Lock:Orange/Black,pin 8

(+) 12V Input: Red: 6 & 12


1

2

3

4RX: pin 4 TX: pin 3

228

1012

42

44

2

DS4+

DS4

Slideto open


DS4+ DS4


MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


5

30

20

20

5

15

15

(+) Ignition Input/Ouput: Pink: 10

(+) Accessory Output: Orange: 8




Ignition Switch(black conn. at ign. switch)1 2 3 4 5 6 7

141

15

163

174

185

196

207

218

229

2310

2411

2512

2613

2


(-) Factory AlarmDisarm: Green/Violet orLt.Blue/Black, pin 9

Smart Junction Box(black conn.

passenger kick panel)

(+) 12V: Lt.Green/Violet, pin 4

(+) Ignition:White/Yellow,

pin 1

(+) Accessory: Black/Pink, pin 6

(+) Starter: Dk. Green, pin 7



13

1

26

14

39

27

52

40



(-) Trunk Release: White/Violet, pin 13

30

86 8587

87a

Headlight SwitchGround: Black, pin 7

Cut

(-) Parking Light:Black/Lt. Green, pin 5

Headlight Switch(gray conn.

headlight switch)

(+) Starter Input (key. side): Green: 6

Cut














12V Lt. Green/Violet 4 (+) Ignition switch. Black 7 B

Starter Dk. Green 7 (+) Ignition switch. Black 7 B

Ignition White/Yellow 1 (+) Ignition switch. Black 7 B

Accessory Black/Pink 6 (+) Ignition switch. Black 7 B

Parking Lights Black/Lt. Green 5 (-) Headlight switch. Gray 10 D

Headlight Switch Ground Black 7 Cut Headlight switch. Gray 10 D



MS CAN High White/Orange 3 Data OBDII. Black 16 C

MS CAN Low Pink/Orange 11 Data OBDII. Black 16 C

Driver Door Trigger Lt. Green/Black 2 Cut SJB (Smart Junction Box) in passenger kick panel. Black 26 E

Factory Alarm Disarm Green/Violet or Lt. Blue/Black

9 (-) SJB in passenger kick panel. Black 26 E

Lock Orange/Black 8 (-) SJB in passenger kick panel. Black 26 E

Unlock Yellow/Red 5 (-) SJB in passenger kick panel. Black 26 E

Trunk/Hatch Release White/Violet 13 (-) SJB in passenger kick panel. Black 52 F






16

8

9

1


MS CAN Low: Tan: 1

(-) Power Liftgate: Red/White: 4







HS CAN Low: pin 14

HS CAN High: pin 6

MS CAN Low:pin 11

MS CAN High:pin 3




(-) Unlock:Yellow/Violetpin 4

(-) Driver Door Trigger:Green/Black, pin 14

(-) Lock:Blue/Green,pin 17

OBDII Diagnostic Connector,under Driver Dash (connector side view)

12V Input: Red: 6 & 12


1

2

3

4RX: pin 4 TX: pin 3

228

1012

42

44

2

DS4+

DS4

Slideto open


DS4+ DS4


MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


5

30

20

20

5

15

15


(+) Accessory Output: Orange: 8





141

15

163

174

185

196

207

218

229

2310

2411

2512

2613

2


(-) Factory AlarmDisarm: Green/Violet, pin 8

(+) 12V: Red, pin 4

(+) Ignition:White/Orange,

pin 1

(+) Accessory: Violet/Green, pin 6

(+) Starter: Blue/White, pin 7





(+) Parking Lights:Violet/White, pin 6

PowerLiftgate(conn. atliftgateswitch)

(-) Power Liftgate:Gray/Yellow,pin 3

1 2 3

4 5 6

1

8 9 10 11 12 13

75432 6

Smart Junction Box(gray conn. SJB/dash fuse box)

CUT









Ford Taurus X 2008-2009



Power Liftgate Gray/Yellow 3 (-) Power liftgate switch. N/A 6 D





Parking Lights Violet/White 6 (+) Fuse/SJB (Smart Junction Box) under drivers dash. Gray 13 E





Driver Door Trigger Green/Violet 14 Cut Fuse/SJB under drivers dash. Gray 26 F

Lock Blue/Green 17 (-) Fuse/SJB under drivers dash. Gray 26 F

Unlock Yellow/Violet 4 (-) Fuse/SJB under drivers dash. Gray 26 F

Factory Alarm Disarm Green/Violet 8 (-) Fuse/SJB under drivers dash. Gray 26 F

Tach NOT Red N/A (AC) Any fuel injector. N/A N/A N/A





16

8

9

1







HS CAN Low: Pink/Lt.Green, pin 14

HS CAN High: White/Lt.Green, pin 6




(-) Driver Door Trigger


(+) 12V Input: Red: 6 & 12


1

2

3

4RX: pin 4

TX: pin 3

228

1012

42

44

2

DS4+

DS4

Slideto open


DS4+ DS4


MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


5

30

20

20

5

15

15

(+) Ignition Input/Ouput: Pink: 10(+) Accessory Output: Orange: 8





(+) 12V: Green/Violet, pin 4

(+) Ignition:Dk.Blue/Lt.Green, pin 1

(+) Accessory: Black/Lt.Green, pin 6

(+) Starter: Red/Lt.Blue or Blue/White, pin 7

(-) RAP Off Output: Lt. Green: 8

(+) Parking Lights:Black/Lt. Green, pin 5

Headlight Switch(gray conn. at

headlight switch)










Ford F150 2008

RX Gray/Orange 4 Data (PATS) connector. Green 4 A

TX White/Lt. Green 3 Data (PATS) connector. Green 4 A

12V Lt. Green/Violet 4 (+) Ignition switch. Black 7 B

Starter Red/Lt. Blue or Blue/White


Ignition Dk. Blue/Lt. Green 1 (+) Ignition switch. Black 7 B

Accessory Black/ Lt. Green 6 (+) Ignition switch. Black 7 B

Parking Lights Brown 5 (+) Headlight switch. Gray 10 D



Driver Door Trigger Black/Yellow N/A (-) Driver kick panel harness to rear. N/A N/A E

Lock Pink/Yellow N/A (-) Driver kick panel harness to rear. N/A N/A E

Unlock Pink/Lt. Green N/A (-) Driver kick panel harness to rear. N/A N/A E

MS CAN High N/A N/A N/A N/A N/A N/A N/A

MS CAN Low N/A N/A N/A N/A N/A N/A N/A

Tach NOT Red N/A (AC) Any fuel injector. N/A N/A N/A




16

8

9

1


MS CAN Low: Tan: 1

(-) Trunk/Hatch Release Output: Red/White: 4







HS CAN Low: White, pin 14

HS CAN High: White/Blue, pin 6

MS CAN Low: Violet/Orange,pin 11

MS CAN High: Gray/Orange,pin 3








(+) 12V Input: Red: 6 & 12


1

2

3

4RX: Pin 4

TX: Pin 3

228

1012

42

44

2

DS4+

DS4

Slideto open


DS4+ DS4


MAIN (5A) (+)


(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)


5

30

20

20

5

15

15


(+) Accessory 1 Output: Orange: 8




(+) Accessory 2 Output: Pink/White: 4(+) 12V Input: Red: 5

(+) 12V Input (Flex): Red/White: 9

Keysense Output: White: 7


6 1087 9

1 532 4

(+) Keysense: Pin 3


at ignition switch)


(+) 12V: Pin 10

(+) Ignition: Pin 1

(+) Starter: Pin 9







Ford Expedition 2008

RX Blue/Gray 4 Data (PATS) connector. Black 4 A

TX Violet/Brown 3 Data (PATS) connector. Black 4 A




Accessory 1 Brown/Yellow 7 (+) Ignition switch. Gray 10 B

Accessory 2 Violet/Green 5 (+) Ignition switch. Gray 10 B


Parking Lights Violet/White 6 (+) SJB (Smart Junction Box) in passenger kick panel. Gray 13 D





Driver Door Trigger Green/Violet 14 Cut SJB in passenger kick panel. Gray 26 E

Hatch Release Brown 7 (-) SJB in passenger kick panel. Gray 26 E

Lock White/Brown 17 (-) SJB in passenger kick panel. Gray 26 F

Unlock Blue/Brown 4 (-) SJB in passenger kick panel. Gray 26 F

Tach NOT Violet/Green N/A (AC) Any fuel injector. N/A N/A N/A



Key2GOThis feature is required if only one key is available. You can program the interface without the need for Key2GO if two keys

are present.

Key2GO has been designed and developed to bypass the advanced encryption layers found in modern vehicles. It uses an array of servers to generate a duplicate of the original key, allowing the installation of a remote starter without having to give up a key.

The advantage is that this feature allows you to use one original key and the server to configure the bypass in the vehicle.

All Key2GO-compatible firmware are clearly indicated in the function list of each vehicle search result page and will also appear on the flash page. Any first-time user must re-register to gain access to Key2GO, and some additional information will be required to complete the registration process, such as your Directed account number and store name.

Key2GO is compatible with XKLoader2 and the online web tool, as well as XKLoader3 and the Directechs Mobile application.

Refer to "Module programming - 1-Key programming using Key2GO" on page 55 of this guide for instructions on how to program features using Key2GO.

Understanding the difference between a Ford 80 & 40 bitFord introduced an 80-bit encryption in late 2009 and this caused a lot of confusion as to which models it was available on. The main question is which models use the 80 and which use the old 40 bit?

Contrary to popular belief, the SA marking on the key does NOT indicate a vehicle uses 80-bit encryption. In reality, the SA marking indicates that the key is 80-bit compatible, but the vehicle itself could still be using 40-bit encryption.

What does it mean? It means that Ford did in fact release SA keys equipped with an 80-bit transponder, but the reality is that the same transponder can also be used in 40-bit vehicle, making it backward compatible with older vehicles. Consequently, if you see an SA key it is important that you do not automatically assume it is an 80-bit type. It all depends on the vehicle, not the key.

How do I differentiate between the 40 & 80 bit?To determine which encryption type you are dealing with, you must test pin 1 at the 4-pin IMMO connector on the key barrel for the following conditions to determine if it is 40 or 80-bit type.

An 80-bit vehicle should provide the following values:• NO key in barrel: 0V• Key in barrel with IGN OFF: (+) 12V• Key in barrel with IGN ON: (+) 12V

A 40-bit vehicle should provide the following values:• NO key in barrel: 0V• Key in barrel with IGN OFF: 0V• Key in barrel with IGN ON: (+) 12V


Configuring the system

Important!Once the DS4+ module is installed in the vehicle following the instructions in "Installation (wiring diagrams, fuse selection & vehicle wiring reference charts)" on page 8, launch the DirectLink application on your mobile device, and select Configure DS4/DS4+. Follow the on-screen instructions to configure the system.

Note: Your system can also be configured using XKLoader2 on www.directechs.com.

Vehicles equipped with a manual transmissionAdditional connections may be required if these functions are not supported by the firmware.

Connection Description

(-) E-Brake Status Input (Black/White, pin 17)

Must be connected to a working emergency brake in the vehicle. Although most vehicles have simple (-) trigger emergency brake circuits note some vehicles do not and may require unique integration methodologies.

(-) Door Trigger Input (Green, pin 20) OR (+) Door Input (Violet, pin 13)

Must be connected to a working door trigger in the vehicle, which monitors all doors. The unit must monitor the door pins to allow the Ready Mode process to be enabled.Note: Some vehicles may require unique integration methodologies for this circuit. For more information, refer to www.directechs.com.

(AC) Tachometer Input (Violet/White, pin 22)

Must be connected to a working tachometer signal in the vehicle (fuel injector, ignition coil, true tach, etc.) and learned successfully to the DS4+.

RF SystemsAn RF System consists of one or multiple remotes, a Control Center (antenna), and an antenna cable – various combinations exist. An RF System allows the vehicle owner to control the system with enhanced range. Two-way models are available. Please follow the instructions included with the kit for appropriate installation and programming information.

8504D Combo SensorThe 8504D Combo Sensor must be paired to the device before it can be used. To enter pairing, turn the vehicle ignition to the ON position, then press and hold the programming button on the Control Center (antenna) until the LED starts flashing. Once pairing mode has been entered, your Combo Sensor is ready to use.

Your Combo Sensor is preset for the majority of applications, however it can be adjusted using the DirectLink application, as well as a compatible LED or LCD remote. Please refer to the instructions included with your sensor for more information on how to make adjustments.


When used in conjunction with SmartStartTo enable D2D communication between the DS4+ and the SmartStart one of the following actions must be executed:• SmartStart with Loops – The brown loop must be cut. • SmartStart with Pigtails – The gray wire must be connected to a ground source.

Loops Pigtails

DO NOT connect the SmartStart 2-pin power harness when using the DS4+. Power and ground will be provided by the D2D connector on main module. Refer to the SmartStart documentation for further details.

D2D port configurationThe system will automatically configure the D2D ports based on your selections in the module programming. The white D2D port is reserved for SmartStart. To ensure proper functionality with SmartStart, it is important that it is selected in the system programming of the DirectLink application or via the online web tool.

Note: Both black D2D ports are reserved for the Control Center (antenna) and 8504D Combo Sensor.


Module programming - Using 2 KeysRefer to "LED diagnostics and troubleshooting" on page 56 for more information and for troubleshooting purposes.

To connect the module:

1Please ensure that the vehicle is in a safe location and cannot move forward during programming. For vehicles equipped with a manual transmission, make sure the gearshift lever is in the neutral position.

2 Connect all the harnesses to the DS4+, EXCEPT the 12-pin main power harness.Connect all but the 12-pin harness

3Connect the 12-pin main power harness, and wait until the LED turns ON solid red.

Note: To skip the transponder programming and use the convenience features only, press the programming button 5 times. When the LED turns ON solid orange, proceed to step 4.

Must be connected LAST

&Solid

4Insert the first key and turn it to the ON position, wait at least3 seconds but no more than 10 seconds then remove it.The LED flashes green.

& &START

Key OUT ONOFF

START

Key IN ONOFF

START

Key IN ONOFF

START

Key IN ONOFF

START

Key OUT ONOFF

START

Key IN ONOFF

START

Key IN ONOFF

START

Key IN ONOFF

START

Key OUT ONOFF

START

Key IN ONOFF

START

Key IN ONOFF

START

Key IN ONOFF

START

1st Key OUT ONOFF

START

1st Key IN ONOFF

START

1st Key IN ONOFF

START

1st Key IN ONOFF

START

2nd Key OUT ONOFF

START

2nd Key IN ONOFF

START

2nd Key IN ONOFF

START

2nd Key IN ONOFF

1st

START

Key OUT ONOFF

START

Key IN ONOFF

START

Key IN ONOFF

START

Key IN ONOFF

START

Key OUT ONOFF

START

Key IN ONOFF

START

Key IN ONOFF

START

Key IN ONOFF

START

Key OUT ONOFF

START

Key IN ONOFF

START

Key IN ONOFF

START

Key IN ONOFF

START

1st Key OUT ONOFF

START

1st Key IN ONOFF

START

1st Key IN ONOFF

START

1st Key IN ONOFF

START

2nd Key OUT ONOFF

START

2nd Key IN ONOFF

START

2nd Key IN ONOFF

START

2nd Key IN ONOFF

1st

Key at ON Key out after 3-10 sec.Flashes

5

Within 5 seconds, insert the second key and turn it to the ON position, wait at least 3 seconds but no more than 10 seconds then remove it.The LED now flashes orange, otherwise repeat steps 4 and 5.

Note: In some vehicles, it may be necessary to turn the key to the ON position once more before proceeding to the next step. Important! Proceed with the next step within 5 seconds.

& &START

Key OUT ONOFF

START

Key IN ONOFF

START

Key IN ONOFF

START

Key IN ONOFF

START

Key OUT ONOFF

START

Key IN ONOFF

START

Key IN ONOFF

START

Key IN ONOFF

START

Key OUT ONOFF

START

Key IN ONOFF

START

Key IN ONOFF

START

Key IN ONOFF

START

1st Key OUT ONOFF

START

1st Key IN ONOFF

START

1st Key IN ONOFF

START

1st Key IN ONOFF

START

2nd Key OUT ONOFF

START

2nd Key IN ONOFF

START

2nd Key IN ONOFF

START

2nd Key IN ONOFF

2nd

START

Key OUT ONOFF

START

Key IN ONOFF

START

Key IN ONOFF

START

Key IN ONOFF

START

Key OUT ONOFF

START

Key IN ONOFF

START

Key IN ONOFF

START

Key IN ONOFF

START

Key OUT ONOFF

START

Key IN ONOFF

START

Key IN ONOFF

START

Key IN ONOFF

START

1st Key OUT ONOFF

START

1st Key IN ONOFF

START

1st Key IN ONOFF

START

1st Key IN ONOFF

START

2nd Key OUT ONOFF

START

2nd Key IN ONOFF

START

2nd Key IN ONOFF

START

2nd Key IN ONOFF

2nd

Key at ON Key out after 3-10 sec.

Flashes

6

Wait for at least 3 seconds, but no more than 10 seconds, and pressand hold the programming button.The vehicle ignition turns ON.The LED turns ON solid green for 3 seconds, then turns OFF.

Note: Release the Program button as soon as the orange LED goes out. If you wait too long to release the programming button, you will have to start the programming over.

Press & Hold

Release

&Solid Off

&

7Pair remotes (if applicable). For information on how to pair a specific remote, please refer to its corresponding owner documentation, which can be found inside the product packaging of the complete system or on www.directechs.com.*

Pair remotes*

8 By default, the tachometer is preprogrammed for the vehicle. For instructions on how to program tach, see page 59.

Initialize tachometer

* Your aftermarket remote may differ from the model shown in the illustrations.

You have successfully completed the module programming sequence.



Module programming - 1-Key programming using Key2GORefer to "LED diagnostics and troubleshooting" on page 56 for more information and for troubleshooting purposes.

To connect the module:

1Please ensure that the vehicle is in a safe location and cannot move forward during programming. For vehicles equipped with a manual transmission, make sure the gearshift lever is in the neutral position.

2 Connect all the harnesses to the DS4+, EXCEPT the 12-pin main power harness.

Connect all but the 12-pin harness

3 Connect the 12-pin main power harness, and wait until the LED turns ON solid red.

Must be connected LAST

&Solid

4 Insert the key and turn ignition ON and OFF twice. The LED now flashes orange.

START

Key OUT ONOFF

START

Key IN ONOFF

START

Key IN ONOFF

START

Key IN ONOFF

Flashes Orange

&

START

Key OUT ONOFF

START

Key IN ONOFF

START

Key IN ONOFF

START

Key IN ONOFF

X 2

5Remove the module from the vehicle and reconnect it to your computer. The Directechs web site will automatically recognize that you are moving on to the second phase of the programming sequence.

6 Select the method and click on Submit Key2GO Request.

7 Once the configuration is completed, reconnect the unit to the vehicle. The LED then turns ON solid green for 3 seconds once the module is successfully programmed. Solid x 3 secs

8Pair remotes (if applicable). For information on how to pair a specific remote, please refer to its corresponding owner documentation, which can be found inside the product packaging of the complete system or on www.directechs.com.*

Pair remotes*

9 By default, the tachometer is preprogrammed for the vehicle. For instructions on how to program tach, see page 45.

Initialize tachometer

* Your aftermarket remote may differ from the model shown in the illustrations.

You have successfully completed the module programming sequence.


LED diagnostics and troubleshootingThis section provides LED diagnostics and troubleshooting information to guide you through the various stages of your installation.

Module programming

LED Description Troubleshooting

OffModule has no power. Make sure the D2D harness is connected and that 12 Volt is present between the red and black

wires. If 12 Volt is present, the module may be defective.

Solid red

Waiting to begin the programming sequence. Ensure the correct programming procedure is being followed.

Flashes red & green

Initialization failed. Reset the module and complete the programming again. If the issue persists, please contact Technical Support.

Solid orangeTransponder functions were skipped. (If compatible) when the RXT mode is not desired or convenience features are needed, please

reset and reprogram the module.

Flashes green

All required CAN networks has been detected. Normal operation.

Flashes orange1 of 2 CAN networks has been detected. Normal operation.

Flashes orange slowly

Key2GO initiated. Please follow the steps indicated in "Module programming - 1-Key programming using Key2GO" on page 55 to complete the Key2GO programming.

Solid green x 3 secs

Module was successfully programmed with all functions. Normal operation.

Solid orange x 3 secs

Module was successfullyprogrammed without transponder functions.

Normal operation.

Module programming – Error codes


Flashes red x 1CAN2 not detected.

Check the CAN2 Orange/Green and Orange/Brown wire connections. Wake up the data bus by turning the ignition on and try again. If your installation does not require this connection, skip this step by pressing the programming button 5 times.

Flashes red x 1J1850 not detected. Check the J1850 wire connection. Wake up the data bus by turning the ignition on and try

again.

Flashes red x 2CAN1 not detected.

Check the CAN1 Tan and Tan/Black wire connections. Wake up the data bus by turning the ignition on and try again. If your installation does not require this connection, skip this step by pressing the programming button 5 times.

Flashes red x 3Bypass data not detected. Check the bypass line connection. If more than one wire is used, make sure they are not inverted.

Ensure the vehicle still operates correctly using the factory key.

Flashes red x 4Bypass processing error. The bypass calculation failed. Reset the module and try again. If the condition persists, please

contact Technical Support.

Flashes red x 5ISO 1 not detected. The Yellow/Black wire did not detect the expected signal. Refer to "Installation (wiring diagrams,

fuse selection & vehicle wiring reference charts)" on page 8 to check the connections.

Flashes red x 6ISO 2 not detected. The Orange/Black wire did not detect the expected signal. Refer to "Installation (wiring diagrams,

fuse selection & vehicle wiring reference charts)" on page 8 to check the connections.

Flashes red x 7MUX not detected.

The Violet/Green or Violet/Brown wire did not detect the expected voltage value. Refer to "Installation (wiring diagrams, fuse selection & vehicle wiring reference charts)" on page 8 to check the connections.

External module synchronization


(Flashes red, red, then orange) x 10

OBDII feature not supported. The diagnostic data bus was not detected, therefore the SmartStart features will be limited.


Active Ground When Running (Status)


Flashes green

Ground When Running (Status) command received. The module has initialized the remote start sequence.

Flashes red & orange

Ignition ON command received. The module has received the Ignition ON command and is processing the remote start sequence.

Flashes green quickly

Start ON command received. The module has received the Start ON command and is processing the remote start sequence.

Flashes red x 10PTS shutdown error. The PTS output from the module was not activated due to safety protection.

Flashes red x 21CAN bus incorrectly detected. Verify the CAN1 and CAN2 connections. Refer to "Installation (wiring diagrams, fuse selection &

vehicle wiring reference charts)" on page 8 to check the connections.

Commands


Flashes orange x 1LOCK command received.

If the bypass module fails to flash, it did not receive the signal. Commands can come from RF or D2D.

Flashes orange x 2UNLOCK command received.

Flashes orange x 3TRUNK command received.

Flashes orange x 4AUX1 command received.



Shutdown codes


Flashes green x 1Takeover successful. Normal operation.

Flashes red x 1Runsafe was not disabled. No UNLOCK command was received prior to opening the door, or the 45 second timer expired

in takeover mode.

Flashes red x 2Brake was not detected. The brakes were not detected, which prevents the system from shutting down the vehicle.

Flashes red x 3Smart key was not detected. The smart key was not detected, which prevents the system from shutting down the vehicle.

Flashes red x 4Speed was detected. The vehicle was detected as moving, which prevents the system from shutting it down.

Analog error codes


Flashes red, green & orange

DEI feature error. A feature config file mismatch was detected. Please contact Technical Support.


Soft resetA module reset will only erase the steps performed in "Module programming - Using 2 Keys" on page 54. The firmware and settings flashed to the module will not be affected.

1If required for your installation, connect all the harnesses to the DS4+, EXCEPT the 12-pin main power harness. Press and hold the programming button, then connect the 12-pin harness to the module.


2 Wait 3 seconds until the LED turns ON solid orange then release the programming button. The LED turns ON solid red.

&&ReleaseSolid Solid

Hard resetWarning Against Executing a Hard Reset! A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings may need to be reconfigured. Connect your module to a computer and use the web configuration tool to edit its programmable features.

1If required for your installation, connect all the harnesses to the DS4+, EXCEPT the 12-pin main power harness. Press and hold the programming button, then connect the 12-pin harness to the module.


2 After 3 seconds the LED turns ON solid orange. Keep holding the programming button until the LED flashes red, then orange slowly.

HoldSolid Flashes

&&

3 Release the programming button. The LED turns ON solid red. &Release Solid


Learning the Tach (not needed with Virtual Tach)Tach comes preprogrammed, therefore learning is not required; however, it can be readjusted with the following operations:1. Start the vehicle using the key. 2. Within 5 seconds, press and hold the Control Center* (antenna) or the main module programming button, until the LED on the

Control Center (antenna) or the main module turns ON solid.3. Release the button. Tachometer value is now stored in memory.If the LED does not turn ON solid, find an alternate tach source.

* If the Control Center (antenna) was not included in your kit, the tach can be programmed using the programming button directly on the main module.

Note: When the tachometer is programmed, the main module automatically enters the Tachometer engine checking mode.

Initializing Virtual Tach (not needed with hardwired or data tach applications)To program Virtual Tach:1. After the install is complete, remote start the engine. The programming operation may require 3 cranks of the starter before the

engine starts and runs. Do not turn off the remote start if this happens, it is a normal programming operation.2. Once the engine begins running, let it run for at least 30 seconds.3. Using the Remote, send the Remote start command to turn remote start off. Virtual Tach is programmed. To reset Virtual Tach, a

module reset must be done.

Note: Virtual Tach cannot be used in Manual Transmission Mode. It is also not recommended for diesel trucks.

Virtual Tach handles disengaging the starter motor during remote starting – it does not address over-rev. If the customer wants to have the over-rev protection capability, the tach wire or data tach must be used.

Important! After successfully learning Virtual Tach, a small minority of vehicle starters may over crank or under crank during remote start. Use the VirtualTach Fine tune feature in the configuration wizard to adjust the starter output time in 50mS increments to compensate for such an occurrence.


Limited lifetime consumer warrantyDirected Electronics. (“Directed”) promises to the original purchaser to repair or replace (at Directed’s election) with a comparable reconditioned model any Directed unit (hereafter the “unit”), excluding without limitation the siren, the remote transmitters, the associated sensors and accessories, which proves to be defective in workmanship or material under reasonable use during the lifetime of the vehicle provided the following conditions are met: the unit was purchased from an authorized Directed dealer, the unit was professionally installed and serviced by an authorized Directed dealer; the unit will be professionally reinstalled in the vehicle in which it was originally installed by an authorized Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information: consumer’s name, telephone number and address; the authorized dealers name, telephone number and address; complete product description, including accessories; the year, make and model of the vehicle; vehicle license number and vehicle identification number. All components other than the unit, including without limitation the siren, the remote transmitters and the associated sensors and accessories, carry a one-year warranty from the date of purchase of the same. ALL PRODUCTS RECEIVED BY DIRECTED FOR WARRANTY REPAIR WITHOUT PROOF OF PURCHASE FROM AN AUTHORIZED DEALER WILL BE DENIED. This warranty is non-transferable and is automatically void if: the unit’s date code or serial number is defaced, missing or altered; the unit has been modified or used in a manner contrary to its intended purpose; the unit has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defects in materials or construction. The warranty does not cover damage to the unit caused by installation or removal of the unit. Directed, in its sole discretion, will determine what constitutes excessive damage and may refuse the return of any unit with excessive damage. TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NON-INFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEALERS OR INSTALLERS. DIRECTED SECURITY SYSTEMS, INCLUDING THIS UNIT, ARE DETERRENTS AGAINST POSSIBLE THEFT. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS; AND HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE AND/OR VANDALISM. THIS WARRANTY DOES NOT COVER LABOR COSTS FOR MAINTENANCE, REMOVAL OR REINSTALLATION OF THE UNIT OR ANY CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE UNIT. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGE TO VEHICLE, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE SUBJECT TO THE CONDITIONS AS DESCRIBED HEREIN. THIS WARRANTY IS VOID IF THE UNIT HAS NOT BEEN PURCHASED FROM DIRECTED, OR AN AUTHORIZED DIRECTED DEALER, OR IF THE UNIT HAS BEEN DAMAGED BY ACCIDENT, UNREASONABLE USE, NEGLIGENCE, ACTS OF GOD, NEGLECT, IMPROPER SERVICE, OR OTHER CAUSES NOT ARISING OUT OF DEFECT IN MATERIALS OR CONSTRUCTION.

Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State.

This warranty is only valid for sale of product(s) within the United States of America and in Canada. Product(s) sold outside of the United States of America or Canada are sold “AS-IS” and shall have NO WARRANTY, express or implied.

For further details relating to warranty information of Directed products, please visit the support section of Directed’s website at: www.directed.com.

This product may be covered by a Guaranteed Protection Plan (“GPP”). See your authorized Directed dealer for details of the plan or call Directed Customer Service at 1-800-876-0800.

(920-10011-01 2011-06)

DS4+ FORD6© 2017-12-13 Directed. All rights reserved.

Quick Reference Guide

Pit stop/idle mode

1 Stop the vehicle in a safe parking spot and put the gear in Park (P).

Put gear in

Park

2Press the Remote Start button on the transmitter.*

The parking lights will flash once to indicate the vehicle is now in Pit Stop Mode.

Parking lights flash x1

14:36

Press Remote Start button*

&

3

It is safe to leave the engine running and exit the vehicle with the factory remote in hand.

Note: We recommend that you always lock the doors of your vehicle when leaving it unattended.

14:36Exit vehicle with remote

* Icon and remote appearance may differ depending on the model purchased.

List of available commandsNote that the information below is for many Viper, Clifford, Python, Autostart and AstroStart models. Icons and commands may differ depending on the model and options purchased. Refer to your authorized installation center for more specific information.

Button(s) Actions

Press & hold for 1 second to lock.

Press & hold for 1 second to unlock.

* Press & hold for 1 second to remote start.

* Press & hold for 5 seconds to activate the trunk release (optional).


Sending commands to your vehicleWhether you want to remote start the engine, lock/unlock the doors or pop the trunk, there are 3 possible ways you can send commands to your vehicle, using the:• Factory remote.• Aftermarket remote.• Directed SmartStart application via your smartphone.

If applicable, you can also start the engine remotely by pressing the Lock button 3 times quickly on your factory remote.

Vehicle takeover with regular key

1 Close the vehicle doors, hood and trunk, then send the Remote Start command to start the vehicle.* 14:36Press Remote

Start button*

2 Send the Unlock command on the factory or aftermarket remote.*

14:36Press Unlock on either remote*

3 Enter the vehicle, while making sure the factory remote is inside with you.

14:36Enter vehicle with remote

4 Insert your key in the ignition barrel and turn it to the ON position. START

Key OUT ONOFF

START

Key IN ONOFF

START

Key IN ONOFF

START

Key IN ONOFF

5 Depress the brake pedal, put the car in gear and drive off.

Ready to drive off


DS4+ FORD6© 2017-12-13 Directed. All rights reserved.

SmartStart compatibleThis system is compatible with Directed SmartStart. For a complete list of supported features, please visit www.mysmartstart.com.

What is SmartStart?Now you can remote start, lock and unlock your car just by pushing a button on your smartphone; using the SmartStart App from Directed, the leader in vehicle security and remote start. The simple graphical interface gives you control over the following features of your installed remote start or security with remote start system: • Lock/Arm• Unlock/Disarm• Remote Car Starter• Trunk Release• Panic• Aux Channels

You can also control multiple vehicles – great for families – and assign more than one user to control a vehicle. It’s easy with SmartStart! But, this is only the beginning! SmartStart is loaded with additional features including GPS tracking, SmartSchedule, vehicle status, roadside assistance, parked car finder and more.

The application enables a “Cloud-Connected Car” like never before, providing 2-way interaction with your vehicle. Connectivity is managed through the Directed Cloud Services (DCS) network linking car, app, end user, and the Internet.

For more information, visit www.mysmartstart.com.

Notes

FORD6 · PDF file · 2017-12-13The FORD6 firmware for DS4+ is compatible with...

Documents

Transcript of FORD6 · PDF file · 2017-12-13The FORD6 firmware for DS4+ is compatible with...