FOOT PEDALS -...
Transcript of FOOT PEDALS -...
M O D E L F P
FOOT P EDALS
D E S C R I P T I O N
Curtis Model FP foot pedals are designed and manufactured to the exacting requirements of TS16949 to achieve unprecedented reliability.
A P P L I C A T I O N
Curtis Model FP foot pedals are ideal for use with electronic vehicle controllers in material handling, construction, airport, golf, sweeper/scrubber, utility, Light-On-Road and general industrial vehicles.
F E A T U R E S
•Modular design combines standard sensors (resistive or Hall Effect) with flexible mechanical designs to provide solutions for every application.
•Wide temperature range and throttle sensor protection of IP66 allows reliable use of electronic control in harsh industrial vehicle applications.
•Metal and rugged thermoplastic composite versions available to meet the specific cost and performance requirements of each application.
•Multiple pedal angles and mounting configurations (floor, suspended, flush) allow use in wide range of vehicle cab styles and sizes.
• 0–5 Volt operation allows easy integration with existing Curtis and other vehicle controllers.
• Integrated Packard connector eases installation, eliminates historical wiring problems and lowers production costs. A Packard-to-Deutsch adaptor (Curtis Part Number 18140900-0001) is also available.
•SAE J1113 Category 4 compliance for EMI allows safe and reliable use in applications with severe electrical noise.
• Dual, ratiometric or switched (IVS - Idle Validation Switch) outputs ensure safe vehicle and throttle operation.
• Compliance to Federal Motor Vehicle Safety Standard (FMVSS) 124 (return-to-idle) and 302 (flammability) ensure compliance to on-road safety standards.
FP-FCV
FP-SCVFP-SMV
FP-FMV
FP-LCV
www.curtisinstruments.com
M O D E L F P
S P E C I F I C A T I O N S
Absolute Maximum Ratings
ElectricalSupply Voltage (Vcc) 5.5 VDCOutput Current (APS) 30 mA (switched output) 10 mA (dual output)Output Voltage (IVS) 32 VDC (switched output only)Output Current (IPS) 35 mA (switched output only)APS Short Circuit to Ground 20 minutesAPS Short Circuit to Vcc 20 minutes
MechanicalStatic Load Limit 489 N (Model SMV) 1500 N (Model FMV) 1560 N (Models FCV, LCV, SCV)Full Stroke Cycles 3 million
Output Type Pedal Style
Connector Pin Description Mating Connector
Dual Ratiometric
FCV, LCV, SCV, SMV
A APS1
Packard Metri-Pack Series 150 Housing P/N: 12066317 Terminal P/N: 12103881
B GND1
C VCC1 (+5v)
D VCC2 (+5v)
E GND2
F APS2
FMV
A APS1 GND - White
Connector P/N: 12010717B APS1 Signal - Black
C APS1 Supply (+5V) - Red
A APS2 Signal - Orange
Connector P/N: 12015793 B APS2 GND - Blue
C APS2 Supply (+5V) - Green
Switched
FCV, LCV, SCV, SMV
A APS Signal
Packard Metri-Pack Series 150 Housing P/N: 12066317 Terminal P/N: 12103881
B APS GND
C APS Supply (+5V)
D IVS (Normally Open)
E IVS Supply (+12V)
F Unused
FMV
1 IVS Signal - Green
Deutsch “DT” Connector Body P/N: DT04-6P Wedge Lock P/N: W6P Pin Contact P/N: 460-202-1631
2 IVS Supply (+12V) - Blue
3 Unused
4 APS GND - White
5 APS Supply (+5V) - Red
6 APS Signal - Black
M O D E L F P
Typical Output Characteristics
EnvironmentalOperating Temperature Range –40°C to +85°CThermal Cycle/Stress SAE J1455, –40°C to +85°CThermal Shock –40°C to +85°CHumidity 120 hour exposure at 95% from +27°C to +75°CVibration Random broadband 5–500 Hz, 4gShock SAE J1455, 1 meter drop to concreteDust Exposure 24 Hour exposure, pedals cycledPressure Wash Water:1000 psi, +75°C, 40 minutes, 0.05 rpm Detergent: 250 psi, +75°C, 40 minutes, 0.05 rpmChemical Exposure Diesel Fuel, Brake Fluid, Antifreeze, Plastic Protectant
RegulatoryReturn-to-Idle Certification FMVSS–124Flammability FMVSS–302
Dual, Ratiometric Output Version Switched Output Version
ANGULAR POSITION
AP
S O
UTP
UT
VO
LTA
GE
APS1OUTPUT
APS2OUTPUT
V (84%) WOTI
V (42%) WOT2
V (22%)CT1
V (11%)CT2
SENSOREND-STOP ESCW(+58.3º)
WOT(48.3º)
2(+45.8º)
0ºREF
1(-2.7º)
CT(-5.2º)
SENSOREND-STOP ESCCW(-15.2º)
S P E C I F I C A T I O N S c o n t i n u e d
116±2
224.4±6.5
22.3
46.7±6.5
95.3 ±0.5
38.1 ±0.25
69.6±0.25
+0.5−0.1Ø9.5 −DFT
+0.4−0.12X Ø8.6 +DFT
101.9±6
19º ± 2ºTOTALROTATION
16º ± 2ºTO WOT
M O D E L F P
D I M E N S I O N S m m
Model FP-SCV
M O D E L E N C O D E M E N T
FP X Y Z 001Foot Pedal Mounting Material Sender Sequential Code
F=Floor C=Composite V=0–5V
L=Low Profile (flush) M=Metal R=0–5kΩ
S=Suspended
M O D E L F P
C
84.33
189.23±6.35
A
A
195.07±6.35
19.5º±1.0ºROTATION
146.05
PEDAL TILTED (2º)
5.59±6.35
2X (Ø7.87)
96.52±1.5
58.42
54.10
45º
49.78 33.02X (R.16.0)
D I M E N S I O N S mm
Model FP-SMV
M O D E L F P
D I M E N S I O N S mm
Model FP-LCV
PEDAL ASSY SHOWN AT W.O.T.
22º ±2º
267
65
16º ±2º ROTATION
PEDAL ASSY SHOWN AT IDLE
191
91 104
63
94
5
71
3X (Ø9)
M O D E L F P
D I M E N S I O N S mm
Model FP-FMV
153
83
3
4
21
41
134
249
940
35°± 2°
17°± 2° STROKE
217
37
64
49
25
13 89
111
20
32
16
4X (Ø9 THRU)
2X (Ø10 THRU)
M O D E L F P
Specifications subject to change without notice 50165 REV D 2/11©2011 Curtis Instruments, Inc. is a trademark of Curtis Instruments, Inc.
WA R R A N T Y Two year limited warranty from time of delivery.
D I M E N S I O N S mm
144
42
143
85.3
106 181
136.9
30
33
17.3
203.7
SENSOR
17° STROKE
30°
MOUNTING HOLE PATTERN
38
43
8
151
9535 5X(Ø9)
Model FP-FCV