Fluke 725, 725Ex, 726 Multifunction Process Calibrators Data Sheet
2
725/725Ex/726 Multifunction Process Calibrators 10031 -eng Rev. 07 Included Accessories TL75 Test Leads, AC72 Test Clips, one pair of stackable test leads, user’s Manuals on CD-ROM (725Ex also includes CCD control drawing, Statement of Quality Assurance Practices, NIST Traceable calibration certificate) Ordering Information Fluke 725 Multifunction Process Calibrator Fluke 725Ex Intrinsically Safe Multifunction Process Calibrator Fluke 726 Precision Multifunction Process Calibrator C125 TL220 80PK-27 TPAK 700P27 More calibration power! 72 5/72 5Ex/7 26 M ult ifun ctio n Proce ss C al ibr at or s • Two separate channels; measure, source and view process signals s imultaneously • Measure volts, mA, RTDs, thermocouples, frequency, and resistance to test sensors and transmitters • Source/simulate volts, mA, thermocouples, RTDs, frequency, and pressure to calibrate transmitters • Measure or *source pressure using any of 29 Fluke 700Pxx Pressure Modules • Source mA with simultaneous pressure measurement to conduct valve and I/P tests • Perform fast linearity tests with auto step and auto ramp features • Power transmitters during test using 24 V loop supply and simultaneous mA measurement • Store frequently-used test setups for later use *Pressure pump required 72 6 Prec isi on M ult ifun ctio n Process C ali br at or Additional features: • More precise measurement and calibration source performance, accuracies of 0.01% • Transmitter error% calculation • Memory storage for up to 8 calibration results • Frequency totalizer and frequency pulse train source mode for enhanced flowmeter testing • HART mode inserts 250 ohm resistor in mA measure and source for compatibility with HART instrumentation • Integrated pressure switch test allows you to capture the set, reset and deadband of a switch • Custom RTD curves, add calibration constants for certified RTD probes for enhanced temperature measurement Function Range or Type Resolution Accuracy Notes Measure or Source Voltage 0 to 100 mV 0.01 mV 0.01% , Max load, 1 mA 0 to 10V (source) 0.01V 0.02% Rdg + 2 0 to 20 V (sour ce) 0.01 V LSD 0 to 30 V (measure) 0.01 V mA 0 to 24 0.001 mA 0.01% ; 0.02% Rdg Max load, + 2 LSD 725/726: 1000 Ω 725Ex: 500Ω mV -10.00 mV to +75.00 mV 0.01 mV 0.01% (TC terminals) 0.02% of range + 1 LSD Ohms 15Ω to 3200Ω 0.01Ω to 0.10Ω to 1.0Ω 5Ω to 40 00 Ω 0.1 Ω 0.015% Hz - CPM 2.0 to 1000 CPM 0.1 CPM ±0.05% Source; 1 to 1100 Hz 1 Hz ±0.05% 5V p-p 1.0 to 10.0 kHz 0.1 kHz ±0.25% 1V - 20 V p-p 10.0 to 15.0 kHz 0. 1 kHz 0.5% squarewave, -0.1 V offset Loop Supply 725/726: 24 V DC N/A 10% 725Ex: 12 V DC T/C J, K, T, E, L, N, U, XK 0.1 ºC, 0.1 ºF to 0.7 ºC to 0.2 º C T/C B, R, S, BP 1 ºC, 1 ºF to 1.7 ºC to 1.2 º C RTDs Cu (1 0), Ni120 (672) 0.01 º C , to 0.15 º C Pt 100, 200, 500, 1000 (385) 0.01 º F Pt 100 (3916), Pt 100 (3926) 0.1 ºC, 0. 1 F to 0.2 ºC M axim um volta ge : 30V O pe rat ing tem pe rat ure : 10°C to 55°C Safet y: CSA C22.2 No. 1010.1:1992 EMC: EN50082-1:1992 and EN55022: 1994 Class B Size (H xWxD ): 200 mm x 96 mm x 47 mm Weight : 0.65 kg B att er y: Four AA alkaline batteries. B att er y life: 25 hours typical; battery door Warra nty 725 , 726 : Three years Warra nty 725 Ex: One year Fluke 725 Specifications Features Simultaneous Functi on Channel A Chan nel B Capability 24.000 mA DC M M or S 24.000 mA DC with M 24 V loop supply 100.00 mV DC M or S 30.000V DC Measure M 20.000V DC Measure M or S 10.000V DC Source 20 .000 V DC Source 15 to 3200 Ohms M or S 5 to 40 00 Ohms Thermocouple J, K, T, E, R, S, B, M or S M, L, U, N, XK, BP RTD Cu 10, Ni120; Pt100 (392); M or S Pt100 (JIS); Pt100, 200, 500, 1000 (385) Pr es su re (r equ ir es Fl uke 700P XX M M us ed as S Modules) Frequency; 10 kHz; (15 KHz) M or S M = Measure S = Source/Simulate Unique 726 features are in bold 725Ex: ATEX cerfified (Ex ATEX II IG EEX 1a IIB 171°C) Unique 726 features are in bold Fluke 726 Ne w New Fluke 725Ex Recommended Accessories (Not for hazardous zones)
-
Upload
poochipandy -
Category
Documents
-
view
12 -
download
0
Transcript of Fluke 725, 725Ex, 726 Multifunction Process Calibrators Data Sheet
7/15/2019 Fluke 725, 725Ex, 726 Multifunction Process Calibrators Data Sheet
http://slidepdf.com/reader/full/fluke-725-725ex-726-multifunction-process-calibrators-data-sheet 1/1
725/725Ex/726 MultifunctionProcess Calibrators
10031-eng Rev. 07
Included AccessoriesTL75 Test Leads, AC72 Test Clips, one pairof stackable test leads, user’s Manuals onCD-ROM (725Ex also includes CCD controldrawing, Statement of Quality AssurancePractices, NIST Traceable calibrationcertificate)
Ordering InformationFluke 725 Multifunction Process CalibratorFluke 725Ex Intrinsically Safe Multifunction
Process Calibrator
Fluke 726 Precision Multifunction ProcessCalibrator
C125 TL220 80PK-27 TPAK 700P27
More calibration power!
725/725Ex/726 MultifunctionProcess Calibrators
• Two separate channels; measure, sourceand view process signals simultaneously
• Measure volts, mA, RTDs, thermocouples,frequency, and resistance to test sensorsand transmitters
• Source/simulate volts, mA, thermocouples,RTDs, frequency, and pressure to calibratetransmitters
• Measure or *source pressure using any of 29 Fluke 700Pxx Pressure Modules
• Source mA with simultaneous pressuremeasurement to conduct valve and I/Ptests
• Perform fast linearity tests with auto stepand auto ramp features
• Power transmitters during test using 24 Vloop supply and simultaneous mAmeasurement
• Store frequently-used test setups forlater use
*Pressure pump required
726 Precision Multi functionProcess CalibratorAdditional features:
• More precise measurement and calibrationsource performance, accuracies of 0.01%
• Transmitter error% calculation
• Memory storage for up to 8 calibrationresults
• Frequency totalizer and frequency pulsetrain source mode for enhanced flowmetertesting
• HART mode inserts 250 ohm resistor inmA measure and source for compatibilitywith HART instrumentation
• Integrated pressure switch test allows youto capture the set, reset and deadband of a switch
• Custom RTD curves, add calibrationconstants for certified RTD probes forenhanced temperature measurement
Function Range or Type Resolution Accuracy NotesMeasure or Source
Voltage 0 to 100 mV 0.01 mV 0.01%, Max load, 1 mA0 to 10V (source) 0.01V 0.02% Rdg + 20 to 20 V (source) 0.01 V LSD0 to 30 V (measure) 0.01 V
mA 0 to 24 0.001 mA 0.01%; 0.02% Rdg Max load,+ 2 LSD 725/726: 1000Ω725Ex: 500Ω
mV -10.00 mV to +75.00 mV 0.01 mV 0.01%(TC terminals) 0.02% of range +
1 LSD
Ohms 15Ω to 3200Ω 0.01Ω to 0.10Ω to 1.0Ω5Ω to 4000Ω 0.1Ω 0.015%
Hz - CPM 2.0 to 1000 CPM 0.1 CPM ±0.05% Source;1 to 1100 Hz 1 Hz ±0.05% 5V p-p1.0 to 10.0 kHz 0.1 kHz ±0.25% 1V - 20 V p-p10.0 to 15.0 kHz 0.1 kHz ±0.5% squarewave,
-0.1 V offset
Loop Supply 725/726: 24 V DC N/A 10%725Ex: 12 V DC
T/C J, K, T, E, L, N, U, XK 0.1 ºC, 0.1 ºF to 0.7 ºCto 0.2 ºC
T/C B, R, S, BP 1 ºC, 1 ºF to 1.7 ºCto 1.2 ºC
RTDs Cu (10), Ni120 (672) 0.01 ºC, to 0.15 ºCPt 100, 200, 500, 1000 (385) 0.01 ºF
Pt 100 (3916),Pt 100 (3926) 0.1 ºC, 0.1 F to 0.2 ºC
Maximum volt age: 30VOperating temperature: 10°C to 55°CSafety: CSA C22.2 No. 1010.1:1992EMC: EN50082-1:1992 and EN55022:1994 Class B
Size (HxWxD): 200 mm x 96 mm x 47 mmWeight: 0.65 kgBattery: Four AA alkaline batteries.Battery life: 25 hours typical; battery doorWarranty 725, 726: Three yearsWarranty 725Ex: One year
Fluke 725
SpecificationsFeatures
Simultaneous Function Channel A Channel BCapability
24.000 mA DC M M or S
24.000 mA DC with M24 V loop supply
100.00 mV DC M or S
30.000V DC Measure M20.000V DC Measure M or S10.000V DC Source20.000V DC Source
15 to 3200 Ohms M or S5 to 4000 Ohms
Thermocouple J, K, T, E, R, S, B, M or SM, L, U, N, XK, BP
RTD Cu 10, Ni120; Pt100 (392); M or SPt100 (JIS); Pt100, 200, 500,1000 (385)
Pressure (requires Fluke 700PXX M M used as SModules)
Frequency; 10 kHz; (15 KHz) M or S
M = Measure S = Source/SimulateUnique 726 features are in bold725Ex: ATEX cerfified(Ex ATEX II IG EEX 1a IIB 171°C)
Unique 726 features are in bold
Fluke 726
New
New
Fluke 725Ex
Recommended Accessories(Not for hazardous zones)
