Fluid Statics
-
Upload
rashad-fischer -
Category
Documents
-
view
80 -
download
5
description
Transcript of Fluid Statics
![Page 1: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/1.jpg)
Lecture - 2
Fluid Statics
![Page 2: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/2.jpg)
Fluid Statics
Fluid Statics means fluid at rest. At rest, there are no shear stresses, the only force is the normal
force due to pressure is present. Pressure is defined as: “Force per Unit Area” Or
“The amount of force exerted on a unit area of a substance or on a surface.”
This can be stated by the equation:
Units : N/m2(Pa), lbs/ft2 (psf), lbs/in2 (psi)
Area) Finite(For A
Fp Area) Infinite(For
dA
dFp
![Page 3: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/3.jpg)
Example A load of 200 pounds (lb) is exerted on a piston confining oil in a circular cylinder with an inside diameter of 2.50 inches (in). Compute the pressure in the oil at the piston.
Solution:
![Page 4: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/4.jpg)
Principles about Pressure
Two important principles about pressure were described by Blaise Pascal, a seventeenth-century scientist:
1. Pressure acts uniformly in all directions on a small volume of a fluid.
2. In a fluid confined by solid boundaries, pressure acts perpendicular to the boundary.
![Page 5: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/5.jpg)
Direction of fluid pressure on boundaries
![Page 6: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/6.jpg)
Pressure at a Point is same in All direction(Pascal’s Law)
x
xx
zx
p p
Therefore;
cos dl dz Since
0 dzdy p -dy dl cos p ;0F 8.
Zero. toequal bemust direction any in
elementon components force theof Sum :Condition mEquilibriu 7.
rest.at is fluid thesince involved, is force l tangentiaNo 6.
cancel. they because considered benot needdirection y in Forces 5.
direction. verticaland horizontalin pressure avg. are p and p 4.
direction.any in pressure Avg. pLet 3.
paper). of plane ular to(perpendicdy Thickness 2.
rest.at fluid ofelement shaped wedgeaConsider 1.
![Page 7: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/7.jpg)
Pressure at a Point is same in All direction
direction. allin same isrest at fluid ain point any at pressure Thus
case. ldimensiona threea gconsiderinby py p proof alsocan We10.
p p
Therefore;
sin dl dx Since
order.higher todue term3rd Neglecting
0 dzdy dx 2
1sindy dl p -dy dx p ;0F 9.
z
zz
![Page 8: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/8.jpg)
Variation of Pressure in a Static Fluid(Hydrostatic Law)
It states:
“Rate of increase of pressure in vertical downward direction must be equal to Specific Weight of fluid at that point.”
![Page 9: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/9.jpg)
Variation of Pressure in a Static Fluid(Hydrostatic Law)
element.
of faces verticalon the forces pressure theare acting forcesonly the
y, and x is that direction, horizontal in the summed are forces theIf 6.
fluid. gsurroundin thefrom tted transmi:force Surface b.
fluid. e within thmass on thegravity ofaction the:forceBody a.
:aredirection lin vertica acting Force 5.
z. andy x areelement of Dimensions 4.
p. iselement ofcenter at the Pressure 3.
small). very iselement the(Since
element ithin theconstant w be tofluid ofdensity Assume 2.
fluid. static ofelement an Consider 1.
![Page 10: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/10.jpg)
smaller. gets pressure the,elevation) g(increasin
larger gets z as that indicatessign minus The position. vertical tofluid static
ain pressure of variationrelates that expression general theis This
:asequation above can write wey, and x oft independen is p Since
:tionsimplificaAfter
022
zero. toequalit putting anddirection verticalin the forces Summing .9
0 Thus 8.
equal. bemust faces
verticalopposite on the presssures the0,F and 0Fsatisfy To 7. yx
dz
dp
z
p
zyxyxz
z
ppyx
z
z
ppF
y
p
x
p
z
![Page 11: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/11.jpg)
Head) (Pressure p
h
Or
h
h z Say;
z
dz dp
dz dp
limits.chosen eappropriatbetween equation
previous intergatemust werest,at fluid ain anywhere pressure theevaluate To
p
p
![Page 12: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/12.jpg)
Pressure expressed in Height of Fluid
The term elevation means the vertical distance from some reference level to a point of interest and is called z.
A change in elevation between two points is called h. Elevation will always be measured positively in the upward direction.
In other words, a higher point has a larger elevation than a lower point.
Fig shows the illustration of reference level for elevation.
![Page 13: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/13.jpg)
Relationship between Pressure and Elevation:
![Page 14: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/14.jpg)
Pressure Head
It is the pressure expressed in terms of height of fluid.
h=p/ represents the energy per unit wt. stored in the fluid by virtue of pressure under which the fluid exists. This is also called the elevation head or potential head.
p
h
![Page 15: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/15.jpg)
![Page 16: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/16.jpg)
ExampleAn open tank contains water 1.40m deep covered by a 2m thick layer of oil (s=0.855). What is the pressure head at the bottom of the tank, in terms of a water column?
![Page 17: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/17.jpg)
mp
h
hhp
SOLUTION
mh
mp
mkNxh
mkNx
mkN
w
bwe
wwoob
w
w
i
oo
o
w
11.381.9
51.30
30.51kN/m
9.81(1.4)(8.39)2
2
11.3710.140.1hh So
710.181.9
78.16h
:oil of equivalentfor water
/78.16239.8p :interfaceFor
/39.881.9855.0
/81.9
2
oewe
oe
2i
3
3
Solution:
![Page 18: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/18.jpg)
Exercises (Assignment):
1. An open tank contains 5 m water covered with 2 m of oil 8kN/m3). Find the gauge pressure (a) at interface between the liquids and at bottom of the tank.
2. An open tank contains 7ft of water covered with 2.2ft oil (s=0.88). Find the gauge pressure (a) at the interface between the liquids and (b) at the bottom of the tank.
3. If air had a constant specific weight of 12N/m3and were incompressible, what would be the height of air surrounding the earth to produce a pressure at the surface of 101.3 kPa abs?
![Page 19: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/19.jpg)
Absolute and Gage Pressure
Atmospheric Pressure: It is the force per unit area exerted by the weight of air above that surface in the atmosphere of Earth (or that of another planet). It is also called as barometric pressure.
Gauge Pressure: It is the pressure, measured with the help of pressure measuring instrument in which the atmospheric pressure is taken as Datum (reference from which measurements are made).
Absolute Pressure: It is the pressure equal to the sum of atmospheric and gauge pressures. Or
If we measure pressure relative to absolute zero (perfect Vacuum) we call it absolute pressure.
Vacuum: If the pressure is below the atmospheric pressure we call it as vacuum.
gageatmabs ppp
![Page 20: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/20.jpg)
Measurement of Pressure
There are many ways to measure pressure in a fluid. Some are discussed here:
1. Barometers
2. Bourdon gauge
3. Pressure transducers
4. Piezometer Column
5. Simple Manometers
6. Differential Manometers
![Page 21: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/21.jpg)
1. Barometers:
To measure the atmospheric pressure. Procedure:
1. Immerse the open end of tube in a liquid which is open to atmosphere.
2. The liquid will rise in the tube if we exhaust air from the tube.
3. If all the air is removed and the tube is long enough, than only pressure on the surface is the vapour pressure and liquid will reach its max. possible height (y).
yp
pyppp
atm
vapouratmaO
: thannegligible is in tube surface liquidon pressure vapour theIf
![Page 22: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/22.jpg)
2. Bourdon Gauge:
The pressure, above or below the atmospheric pressure, may be easily measured with the help of a bourdon’s tube pressure gauge.
It consists on an elliptical tube: bent into an arc of a circle. This bent up tube is called Bourdon’s tube.
Tube changes its curvature with change in pressure inside the tube. Higher pressure tends to “straighten” it.
The moving end of tube rotates needle on a dial through a linkage system.
![Page 23: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/23.jpg)
3. Piezometer Column/Tube:
A piezometer tube is the simplest form of instrument, used for measuring, moderate pressure.
It consists of long tube in which the liquid can freely rise without overflowing.
The height of the liquid in the tube will give the pressure head (p/) directly.
To reduce capillary error, the tube error should be at least 0.5 in.
![Page 24: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/24.jpg)
4. Manometer:
Manometer is an improved form of a piezometer tube. With its help we can measure comparatively high pressures and negative pressure also. Following are few types of manometers.
1. Simple Manometer
2. Micro-manometer
3. Differential manometer
4. Inverted differential manometer
![Page 25: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/25.jpg)
Simple Manometer:
It consists of a tube bent in U-Shape, one end of which is attached to the gauge point and the other is open to the atmosphere.
Mercury is used in the bent tube which is 13.6 times heavier than water. Therefore it is suitable for measuring high pressure as well.
Procedure:
1. Consider a simple Manometer connected to a pipe containing a light liquid under high pressure. The high pressure in the pipe will force the mercury in the left limb of U-tube to move downward, corresponding the rise of mercury in the right limb.
![Page 26: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/26.jpg)
Simple Manometer:
2. The horizontal surface, at which the heavy and light liquid meet in the left limb, is known as datum line.
Let h1 = height of light liquid in the left limb above datum.
h2 = height of heavy liquid in the right limb above datum.
h= Pressure in the pipe, expressed in terms of head of water.
s1=Sp. Gravity of light liquid.
s2=Sp. Gravity of heavy liquid.
3. Pressure in left limb above datum = h +s1h1
4. Pressure in right limb above datum = s2h2
5. Since the pressure is both limbs is equal So,
h +s1h1 = s2h2
h= (s2h2 - s1h1)
![Page 27: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/27.jpg)
Simple Manometer:
To measure negative pressure:
In this case negative pressure will suck the light liquid which will pull up the mercury in the left limb of U-tube. Correspondingly fall of liquid in the right limb.
6. Pressure in left limb above datum = h +s1h1 + s2h2
7. Pressure in right limb = 0
8. Equating, we get
h = -s1h1-s2h2 = -(s1h1+s2h2)
![Page 28: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/28.jpg)
ExampleA simple manometer containing mercury is used to measure the pressure of water flowing in a pipeline. The mercury level in the open tube is 60mm higher than that on the left tube. If the height of water in the left tube is 50mm, determine the pressure in the pipe in terms of head of water.
Solution:
mm 766h
81650h
Equating;
mm 816
606.13
Z- Zabove limbright in the head Pressure
mm 50h
)501(sh
Z- Zabove limbleft in the head Pressure
22
11
xhs
xhh
![Page 29: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/29.jpg)
ExampleA simple manometer containing mercury was used to find the negative pressure in pipe containing water. The right limb of the manometer was open to atmosphere. Find the negative pressure, below the atmosphere in the pipe.
![Page 30: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/30.jpg)
(Vacuum) 68.67kPa
-68.67kPa
68.67kN/m- 9.81x(-7)
h p pipe in the pressure Gauge
-7mmm -700h
0700h
Equating;
0
Z- Zabove limbright in the head Pressure
mm 700h
)506.13()501(ssh
Z- Zabove limbleft in the head Pressure
2
2211
xxhhh
Solution:
![Page 31: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/31.jpg)
ExampleFigure shows a conical vessel having its outlet at A to which U tube manometer is connected. The reading of the manometer given in figure shows when the vessel is empty. Find the reading of the
manometer when the vessel is completely filled with water.
![Page 32: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/32.jpg)
2.72mh Equating;
72.22.06.13
Z- Zabove limbleft in the head Pressure
1s
Z- Zabove limbright in the head Pressure
line. datum thebe Z- Zandempty be tois vesselheconsider t usLet 1.
water.of headon in termsmercury of head PressurehLet
6.13s and 1
2.0200h
22
11
21
2
mxhs
hxhh
s
mmm
Solution:
![Page 33: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/33.jpg)
mm 4300.43m(2x0.115)0.2 readingmanometer and
0.115m x
27.2x2.725.72 x
: pressures theEquating
27.2x2.722x)(0.2 13.6
limbleft in the head Pressure
2x 0.2
:case in this readingmanometer that know We
5.72x5.72)1(x limbright in the head Pressure
5.72x32.72x3h x
limbright in the water ofheight totalTherefore
limb.left in theamount same by the up go levelmercury the
and limb,right in the metersby x down goes levelmercury let the result, a As
r. with watefilled completely be to vesselheConsider t 2.
![Page 34: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/34.jpg)
Differential Manometer:
It is a device used for measuring the difference of pressures, between the two points in a pipe, on in two different pipes.
It consists of U-tube containing a heavy liquid (mercury) whose ends are connected to the points, for which the pressure is to be found out.
Procedure: Let us take the horizontal surface Z-Z, at which heavy liquid and
light liquid meet in the left limb, as datum line. Let, h=Difference of levels (also known as differential manomter
reading)
ha, hb= Pressure head in pipe A and B, respectively.
s1, s2= Sp. Gravity of light and heavy liquid respectively.
![Page 35: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/35.jpg)
Differential Manometer:
1. Consider figure (a):
2. Pressure head in the left limb above Z-Z = ha+s1(H+h)= ha+s1H+s1h
3. Pressure head in the right limb above Z-Z = hb+s1H+s2h
4. Equating we get,
ha+s1H+s1h = hb+s1H+s2h
ha-hb=s2h-s1h = h(s2-s1)
![Page 36: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/36.jpg)
Differential Manometer:
Two pipes at different levels:
1. Pressure head in the left limb above Z-Z = ha+s1h1
2. Pressure head in the right limb above Z-Z = s2h2+s3h3+hb
3. Equating we get,
ha+s1h1 = s2h2+s3h3+hbWhere;
h1= Height of liquid in left limb
h2= Difference of levels of the heavy liquid in the right and left limb (reading of differential manometer).
h3= Height of liquid in right limb
s1,s2,s3 = Sp. Gravity of left pipe liquid, heavy liquid, right pipe liquid, respectively.
![Page 37: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/37.jpg)
ExampleA U-tube differential manometer connects two pressure pipes A and B. The pipe A contains carbon Tetrachloride having a Sp. Gravity 1.6 under a pressure of 120 kPa. The pipe B contains oil of Sp. Gravity 0.8 under a pressure of 200 kPa. The pipe A lies 2.5m above pipe B. Find the difference of pressures measured by mercury as fluid filling U-tube.
Solution:
20.4m9.81
200p B, pipein head Pressure
12.2m9.81
120p
A, pipein head pressure that know We
water.of head of in termsmercury
by measured pressure of Differnce hLet
13.6s and 2.5mh
200kPa;p 0.8,s 120kPa;p 1.6,s :Given
b
a
1
bbaa
![Page 38: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/38.jpg)
mm 328 m 0.328h
h) x (0.8 20.4h 13.6 16.2
Equating;
h) x (0.8 20.4 s20.4
Z- Zabove B Pipein head Pressure
h 13.6 16.2
h x 13.6 2.5) x (1.6 12.2
.) .(s12.2
Z- ZaboveA Pipein head pressure that know also We
b
1a
h
hsh
![Page 39: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/39.jpg)
Inverted Differential Manometer:
Type of differential manometer in which an inverted U-tube is used. Used for measuring difference of low pressure.
1. Pressure head in the left limb above Z-Z = ha-s1h1
2. Pressure head in the right limb above Z-Z = hb-s2h2-s3h3
3. Equating we get, ha-s1h1 = hb-s2h2-s3h3
(Where; ha, hb are Pressure in pipes A and B
expressed in terms of head of liquid, respectively)
![Page 40: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/40.jpg)
Exercise (Assignment):
1. A simple manometer is used to measure the pressure of oil (sp. Gravity = 0.8) flowing in a pipeline. Its right limb is open to the atmosphere and the left limb is connected to the pipe. The centre of pipe is 90mm below the level of mercury (sp. Gravity = 13.6) in the right limb. If the difference of mercury levels in the two limbs is 150mm, find the pressure of oil in pipe.
![Page 41: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/41.jpg)
Exercise (Assignment):
2. The pressure of water flowing in a pipeline is measured by a manometer containing U-tubes as shown in figure. The measuring fluid is mercury in all the tubes and water is enclosed between the mercury columns. The last tube is open to the atmosphere. Find the pressure of oil in the pipeline.
![Page 42: Fluid Statics](https://reader031.fdocuments.us/reader031/viewer/2022031713/56813482550346895d9b6027/html5/thumbnails/42.jpg)
Exercise (Assignment):
3. A differential manometer connected at the two points A and B at the same level in a pipe containing an oil of Sp. Gravity 0.8, shows a difference in mercury levels as 100mm. Determine the difference in pressures at the two points.