Hilti Firestop Systems

Hilti, Inc. (U.S.) 1-800-879-8000 www.us.hilti.com • en español 1-800-879-5000 • P.O. Box 21148, Tulsa, Oklahoma 74121 Hilti (Canada) Corp. 1-800-363-4458 www.hilti.ca • 2360 Meadowpine Blvd., Mississauga, Ontario L5N 6S2

Hilti. Outperform. Outlast.

Firestop Submittal Package

Project:

Date:

Submitted by:

Hilti Firestop Saving lives through innovation and education

This submittal is auto-generated based on user-selected inputs. Therefore, Hilti makes no representation as to the suitability of these systems for their intended use.

Table Of Contents

UL Listings F-A-1016............................................................................................................................................... 1

CP 618 Product Data Sheet for CP 618 Firestop Putty Stick............................................................................ 4 UL Certificate of Compliance for CP 618 Firestop Putty Stick.............................................................. 5 Safety Data Sheet (SDS) for CP 617 Firestop Putty Pad, CP 618 Putty Stick, and CP 619T Putty Roll...............................................................................................................................................6 LEED Information for CP 618 Putty Stick........................................................................................... 11

CP 680-M Product Data Sheet for CP 680-P and CP 680-M Cast-in Firestop Devices...................................... 12 UL Certificate of Compliance for CP 680-P, CP 680-M, CP 680-PX Cast-in Firestop Devices and CP 681 Tub Box Kit..................................................................................................................... 13 Material Information Statement for Firestop Products........................................................................ 14 LEED Information for CP 680-P and CP 680-M Cast-In Firestop Device........................................... 15

System No. F-A-1016

SECTION A-A

FA 10

16

Page: 1 of 3

Reproduced by HILTI, Inc. Courtesy ofUnderwriters Laboratories, Inc.

June 29, 2015

A

A

1. Floor Assembly — Min 2-1/2 in. (64 mm) thick reinforced lightweight or normal weight (100-150 pcf or 1600-2400 kg/m3) concrete.1A. Floor Assembly — (Optional, Not Shown)—The fire rated unprotected concrete and steel floor assembly shall be constructed of the materials

and in the manner specified in the individual D900 Series designs in the UL Fire Resistance Directory and as summarized below:A. Concrete — Min 2-1/2 in. (64 mm) thick reinforced lightweight or normal weight (100-150 pcf or 1600-2400 kg/m3) concrete.B. Steel Floor and Form Units* — Composite or non-composite max 3 in. (76 mm) deep galv steel fluted units as specified in the individual

Floor-Ceiling Design.2. Firestop Device* — Cast in place firestop device permanently embedded during concrete placement or grouted in concrete floor assembly in

accordance with accompanying installation instructions. The devices may extend a max of 2 in. (51 mm) above the top surface of the concrete.HILTI CONSTRUCTION CHEMICALS, DIV OF HILTI INC — CP 680N-75/2.5", CP 680N-110/4", CP 680N-160/6", CP 682-75/2.5", CP

682-110/4", CP 680-M 2", CP 680-M 3", CP 680-M 4", CP 680-M 6", CP 680-P 2",CP 680-P 3", CP 680-P 4", CP 680-P 6", CP 680-PX 2", CP 680-PX 3"

3. Through Penetrants — One metallic pipe, conduit or tubing to be installed within the firestop device. Pipe, conduit or tubing to be rigidly supportedon both sides of floor assembly. The following types of pipe, conduit or tubing may be used:A. Steel Pipe — Nom 6 in. (152 mm) diam (or smaller) Schedule 10 (or heavier) steel pipe.B. Iron Pipe — Nom 6 in. (152 mm) diam (or smaller) cast or ductile iron pipe.C. Conduit — Nom 6 in. (152 mm) diam (or smaller) rigid steel conduit.D. Conduit — Nom 4 in. (102 mm) diam (or smaller) steel electrical metallic tubing.E. Copper Tubing — Nom 6 in. (152 mm) diam (or smaller) Type L (or heavier) copper tubing.F. Copper Pipe — Nom 6 in. (152 mm) diam (or smaller) Regular) or heavier copper pipe.

2

3

23

1

CCL

ASS I F IED

Classified byUnderwriters Laboratories, Inc.to UL 1479 and CAN/ULC-S115

US ANSI/UL1479 (ASTM E814) CAN/ULC S115F Rating — 2 Hr F Rating — 2 Hr

T Rating — 0 Hr FT Rating — 0 Hr

L Rating At Ambient — Less Than 1 CFM/sq ft (See Item3) FH Rating — 2 Hr

L Rating At 400 F — Less Than 1 CFM/sq ft (See Item 3) FTH Rating — 0 Hr

W Rating — Class 1 (See Items 4B and 4B1) L Rating At Ambient — Less Than 1 CFM/sq ft (See Item3)

L Rating At 400 F — Less Than 1 CFM/sq ft (See Item 3)

1

Page: 2 of 3

The firestop device and metallic penetrant shall be sized as follows:

System No. F-A-1016

FA 10

16

Reproduced by HILTI, Inc. Courtesy ofUnderwriters Laboratories, Inc.

June 29, 2015

Nom Pipe Diam +, ++ Firestop Device

1-1/2 to 2-1/2 in.(38 to 64 mm) - Other than copper pipe or tubing CP680N-75/2.5"or CP682-75/2.5"1-1/2 to 2 in.(38 to 51 mm) - Other than copper pipe or tubing CP 680-M 2", CP 680-P 2, CP 680-PX 2"

2 to 2-1/2 in. (51 to 64 mm) - Copper pipe or tubingCP680N-75/2.5"or CP682-75/2.5"

CP 680-M 2", CP 680-P 2", CP 680-PX 2"

2-1/2 to 3 in. (64 to 76 mm) CP 680-M 3", CP 680-P 3", CP 680-PX 3"

4 in. (102 mm)CP680N-110/4"or CP682-110/4"

CP 680-M 4", CP 680-P 4"

6 in. (152 mm)CP680N-160/6"

CP 680-M 6", CP 680-P 6"

+ When metallic pipes of diameters smaller than those shown above are installed within the device, CP618 Firestop Putty Stick or mineral woolinsulation shall be installed within the device.

++ L Rating applies only to CP 680-M and -P(X) devices and only when the nom diam of pipe equals size of device (2 in. diam pipe in 2" deviceetc.). L Rating does not apply to CP 680N and CP682 devices.

4. Fill, Void or Cavity Material* - Putty (Not Shown) — Min 1 in. (25 mm) thickness of fill material applied within annulus flush with top surface ofdevice.HILTI CONSTRUCTION CHEMICALS, DIV OF HILTI INC — CP 618 Firestop Putty Stick4A. Packing Material (Not Shown) — As an alternate to Item 4, min 4 in. (102 mm) thickness of min 4 pcf (64 kg/m3) mineral wool insulation firmly

packed to the fullest extent possible within annulus flush with top surface of device.4B. Firestop Device* - Top Seal Plug — (Optional. Not Shown) - Top seal plug for use with CP 680-M 2" and CP 680-P 2" devices and nom pipe,

conduit or tubing sizes of 1/2 in. (13 mm) to 2 in. (51 mm) diam. Plug is friction fit into top of firestop device (Item 2) in accordance with themanufacturer's instructions. When top seal plug is used, no putty (Item 4) or packing material (Item 4A) is required. W Rating applies only to nom1, 1-1/4, 1-1/2 and 2 in. (25, 32, 38 and 51 mm) diam copper pipe/tube in conjunction with 2" CPS Top Seal and CP 680-M 2" or CP 680-P(X) 2"devices.HILTI CONSTRUCTION CHEMICALS, DIV OF HILTI INC — CPS Top Seal Plug

2

Page: 3 of 3

4B1. Firestop Device* - Water Barrier Module — (Optional, Not Shown) - Used as an alternate to the top seal plug (Item 4B) and in combinationwith the CP 680-M and CP 680-P(X) devices to achieve a W Rating. Module is threaded onto top of device. See Table below for sizes ofdevice/module and penetrants covered. When water barrier module is used, a W Rating applies to the water barrier module, device andpenetrant sizes specified in Table below. For W Rating with Water Barrier Module, pipe shall be installed from bottom of device.HILTI CONSTRUCTION CHEMICALS, DIV OF HILTI INC — Water Barrier Module

Penetrant Type (See Item 3 above) Nom Penetrant Diam Size of Device/ModuleA, B, C, D 2" 2"

2-1/2" 3"

3" 3"

4" 4"

6" 6"E, F 2" 2"

3" 3"

4" 4"

6" 6"

System No. F-A-1016

FA 10

16

Reproduced by HILTI, Inc. Courtesy ofUnderwriters Laboratories, Inc.

June 29, 2015

* Indicates such products shall bear the UL or cUL Certification Mark for jurisdictions employing the UL or cUL Certification (such as Canada),respectively.

3

Product Information

Hilti, Inc. (USA) 1-800-879-8000 I www.us.hilti.com I en español 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca

Hilti. Outperform. Outlast.

03/1

6 D

BS

Firestop Putty Stick CP 618

Product description ■ An intumescent, non-hardening, firestop putty for cable and pipe

penetrations

Product features ■ Contains no volatile solvents or asbestos ■ Easy to re-penetrate ■ Reusable ■ Easy to add or remove cables ■ Fast installation

Areas of application ■ Single or bundled cables ■ Non-combustible pipe ■ Blank openings

For use with ■ Concrete, masonry and gypsum wall assemblies ■ Wall and floor assemblies rated up to 3 hours

Examples ■ Where telecommunication and data lines penetrate gypsum wall

assemblies ■ Where steel conduit and EMT penetrate concrete and block wall

assemblies ■ Where blank openings exist in concrete and block wall assemblies

Installation instructions ■ See Hilti Literature or third-party listings for complete application and

installation details

FILL, VOID OR CAVITY MATERIAL FOR USE IN THROUGH-PENETRATION

FIRESTOP SYSTEMSSEE UL FIRE RESISTANCE DIRECTORY

66Y7

FM

R

FILL, VOID OR CAVITY MATERIALS CLASSIFIED BY

UNDERWRITERS LABORATORIES, INC.FOR USE IN TROUGH-PENETRATION

FIRESTOP SYSTEMS SEE UL FIRE RESISTANCE DIRECTORY

66Y7

Technical dataVolume 18 in3

Consistency Moldable puttyColor RedApplication temperature 32°F to 104°F (0°C to 40°C)Curing time Non-curingDensity Approx. 1.6 g/cm3

Surface burning characteristics (ASTM E84-96)

Flame Spread: 15 Smoke development: 10

Sound transmission classification (ASTM E 90-97)

49 (Relates to specific construction)

Tested in accordance with UL 1479ASTM E 814ASTM E 84ASTM G21

*At 73°F (23°C) and 50% relative humidity

Hilti FirestopSaving livesthrough innovationand education

4

C E R T I F I C A T E O F C O M P L I A N C E

Certificate Number 20160829-R13240 Report Reference R13240

Issue Date 2016-August-29

Bruce Mahrenholz, Director North American Certification Program UL LLC Any information and documentation involving UL Mark services are provided on behalf of UL LLC (UL) or any authorized licensee of UL. For questions, please contact a local UL Customer Service Representative at http://ul.com/aboutul/locations/

Page 1 of 1

Issued to: Hilti Construction Chemicals, Div of Hilti Inc.

5400 S 122nd East Ave Tulsa, OK 74146

This is to certify that

representative samples of

Fill, Void or Cavity Materials

Fill, Void or Cavity Materials Certified for Canada CP 618 Firestop Putty Stick for use in Through-Penetration Firestop Systems as currently decribed in the UL Fire Resistance Directory and in the Products Certified for Canada Directory.

Have been investigated by UL in accordance with the Standard(s) indicated on this Certificate.

Standard(s) for Safety: ANSI/UL 1479, "Fire Tests of Through-Penetration Firestops," CAN/ULC-S115, "Standard Method of Fire Tests of Firestop Systems."

Additional Information: See the UL Online Certifications Directory at www.ul.com/database for additional information

Only those products bearing the UL Certification Mark should be considered as being covered by UL's Certification and Follow-Up Service. Look for the UL Certification Mark on the product.

5

Page 1/5

Safety Data Sheetacc. to ISO 11014

Printing date 06/30/2015 Reviewed on 06/30/2015Version number 2

41.1.0

* 1 Identification

· Product identifier

· Trade name:Hilti Firestop Putty Bandage CFS-P BACP 617CP 618CP 619CFS-D 1"CFS-D 25

· Relevant identified uses of the substance or mixture and uses advised against No further relevant information available.· Application of the substance / the mixture Construction chemicals

· Details of the supplier of the safety data sheet· Manufacturer/Supplier:Hilti, Inc.5400 South 122nd East Ave.US-Tulsa, OK 74146Phone: (800) 879-8000Fax: (800) 879-7000Español: (800) 879-5000

· Information department:chemicals.hse@hilti.comsee section 16

· Emergency telephone number:Tox Info Suisse - 24 h ServiceTel.: 0041 / 44 251 51 51 (international). Chem-TrecTel.: 1 800 424 9300

* 2 Hazard(s) identification

· Classification of the substance or mixture The product is not classified according to the Globally Harmonized System (GHS).

· Classification according to Directive 67/548/EEC or Directive 1999/45/EC not applicable· Classification system:The classification was made according to the latest editions of the EU-lists, and expanded upon from company and literature data.

· Label elements· GHS label elements Void· Hazard pictograms Void· Signal word Void· Hazard statements Void· Classification system· NFPA ratings (scale 0-4)

00

0Health = 0Fire = 0Reactivity = 0

· Other hazards· Results of PBT and vPvB assessment· PBT: Not applicable.· vPvB: Not applicable.

* 3 Composition/information on ingredients

· Chemical characterization: Mixtures· Description: Fire prevention compound with Polyisobutylene agent base· Dangerous components:78-42-2 tris(2-ethylhexyl) phosphate Xi R36/38 2-5%

· Additional information For the wording of the listed risk phrases refer to section 16.

4 First-aid measures

· Description of first aid measures· General information No special measures required.· After skin contact Immediately wash with water and soap and rinse thoroughly.· After eye contact Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor.· After swallowing Seek immediate medical advice.· Information for doctor· Most important symptoms and effects, both acute and delayed No further relevant information available.

(Contd. on page 2) US

6

Page 2/5

Safety Data Sheetacc. to ISO 11014

Printing date 06/30/2015 Reviewed on 06/30/2015Version number 2

(Contd. of page 1)

41.1.0

· Indication of any immediate medical attention and special treatment needed No further relevant information available.

5 Fire-fighting measures

· Extinguishing media· Suitable extinguishing agents CO2, extinguishing powder or water spray. Fight larger fires with water spray or alcohol resistant foam.· Special hazards arising from the substance or mixtureIn case of fire, the following can be released:Carbon monoxide (CO)Carbondioxide (CO2)

· Advice for firefighters· Protective equipment:Ensure adequate ventilationWear self-contained respiratory protective device.

6 Accidental release measures

· Personal precautions, protective equipment and emergency procedures Wear protective clothing.· Environmental precautions: Do not allow to enter sewers/ surface or ground water.· Methods and material for containment and cleaning up: Pick up mechanically.· Reference to other sectionsSee Section 7 for information on safe handlingSee Section 8 for information on personal protection equipment.See Section 13 for disposal information.

7 Handling and storage

· Handling· Precautions for safe handling No special measures required.· Information about protection against explosions and fires: No special measures required.

· Conditions for safe storage, including any incompatibilities· Storage· Requirements to be met by storerooms and receptacles: keep containers securely closed and dry, store at -5 - 40 °C / 23 - 104 °F· Information about storage in one common storage facility: Not required.· Further information about storage conditions: None.

· Storage class 13· Specific end use(s) No further relevant information available.

8 Exposure controls/personal protection

· Additional information about design of technical systems: No further data; see item 7.

· Control parameters· Components with limit values that require monitoring at the workplace:The product does not contain any relevant quantities of materials with critical values that have to be monitored at the workplace.

· Additional information: The lists that were valid during the creation were used as basis.

· Exposure controls· Personal protective equipment· General protective and hygienic measuresThe usual precautionary measures for handling chemicals should be followed.Avoid contact with the eyes and skin.Keep away from foodstuffs, beverages and feed.Wash hands before breaks and at the end of work.

· Breathing equipment: Not required.· Protection of hands:

Protective gloves.

EN 374The glove material has to be impermeable and resistant to the product/ the substance/ the preparation.Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation

· Material of glovesNitrile rubber, NBRThe selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer tomanufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and hastherefore to be checked prior to the application.

· Penetration time of glove materialThe exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed.

(Contd. on page 3) US

7

Page 3/5

Safety Data Sheetacc. to ISO 11014

Printing date 06/30/2015 Reviewed on 06/30/2015Version number 2

(Contd. of page 2)

41.1.0

· Eye protection:

Tightly sealed goggles.

EN 166 + EN 170· Body protection:

Protective work clothing.

9 Physical and chemical properties

· Information on basic physical and chemical properties· General Information· Appearance:

Form: PastyColor: Red

· Odor: Characteristic· Odour threshold: Not determined

· pH-value: Not applicable.

· Change in conditionMelting point/Melting range: Not determined.Boiling point/Boiling range: undetermined

· Flash point: Not determined

· Flammability (solid, gaseous) Not determined

· Ignition temperature:

Decomposition temperature: Not determined.

· Auto igniting: Product is not selfigniting.

· Danger of explosion: Product does not present an explosion hazard.

· Explosion limits:Lower: Not determinedUpper: Not determined

· Vapor pressure: Not determined

· Density at 20 °C (68 °F): 1.55 g/cm³ (12.935 lbs/gal) (DIN 51757)· Relative density Not determined· Vapour density Not determined· Evaporation rate Not determined

· Solubility in / Miscibility withWater: Insoluble

· Partition coefficient (n-octanol/water): Not determined

· Viscosity:dynamic: Not determinedkinematic: Not determined

· Other information CP 617 - VOC Content: 4.35 g/l (EPA Method 24)CP 618 - VOC Content: 31.5 g/l (EPA Method 24)CP 619 - VOC Content: 4.5 g/l (EPA Method 24)

10 Stability and reactivity

· Reactivity No further relevant information available.· Chemical stability· Thermal decomposition / conditions to be avoided: No decomposition if used according to specifications.· Possibility of hazardous reactions No dangerous reactions known· Conditions to avoid No further relevant information available.· Incompatible materials: No further relevant information available.· Hazardous decomposition products: No dangerous decomposition products known

US

(Contd. on page 4)

8

Page 4/5

Safety Data Sheetacc. to ISO 11014

Printing date 06/30/2015 Reviewed on 06/30/2015Version number 2

(Contd. of page 3)

41.1.0

11 Toxicological information

· Information on toxicological effects· Acute toxicity:· Primary irritant effect:· on the skin: No irritant effect.· on the eye: No irritating effect.· Sensitization: No sensitizing effects known.· Additional toxicological information:When used and handled according to specifications, the product does not have any harmful effects according to our experience and theinformation provided to us.

· IARC (International Agency for Research on Cancer)None of the ingredients is listed.

· NTP (National Toxicology Program)None of the ingredients is listed

· OSHA-Ca (Occupational Safety & Health Administration)None of the ingredients is listed.

12 Ecological information

· Toxicity· Aquatic toxicity: No further relevant information available.· Persistence and degradability No further relevant information available.· Behavior in environmental systems:· Bioaccumulative potential No further relevant information available.· Mobility in soil No further relevant information available.· Ecotoxical effects: Not determined· Additional ecological information:· General notes: Do not allow product to reach ground water, water course or sewage system.· Results of PBT and vPvB assessment· PBT: Not applicable.· vPvB: Not applicable.· Other adverse effects No further relevant information available.

13 Disposal considerations

· Waste treatment methods· Recommendation Must not be disposed of together with household garbage. Do not allow product to reach sewage system.· European waste catalogue:08 04 10 waste adhesives and sealants other than those mentioned in 08 04 09

· Uncleaned packagings:· Recommendation:Disposal must be made according to official regulations.Dispose of packaging according to regulations on the disposal of packagings.Empty packs: May be disposed via the local Green Dot collecting system or EAK waste material code 150102 (plastic packaging materials)

14 Transport information

· UN-Number· DOT, ADR, ADN, IMDG, IATA Void

· UN proper shipping name· DOT, ADR, ADN, IMDG, IATA Void

· Transport hazard class(es)

· DOT, ADR, ADN, IMDG, IATA· Class Void

· Packing group· DOT, ADR, IMDG, IATA Void

· Environmental hazards:· Marine pollutant: No

· Special precautions for user Not applicable.

· Transport in bulk according to Annex II of MARPOL73/78 andthe IBC Code Not applicable.

· Transport/Additional information: Not dangerous according to the above specifications.

· UN "Model Regulation": -

US

(Contd. on page 5)

9

Page 5/5

Safety Data Sheetacc. to ISO 11014

Printing date 06/30/2015 Reviewed on 06/30/2015Version number 2

(Contd. of page 4)

41.1.0

15 Regulatory information

· Safety, health and environmental regulations/legislation specific for the substance or mixture· Sara· Section 355 (Extremely hazardous substances):None of the ingredients is listed.

· Section 313 (Specific toxic chemical listings):None of the ingredients are listed.

· TSCA (Toxic Substances Control Act):All ingredients are listed.

· Proposition 65:· Chemicals known to cause cancer:None of the ingredients are listed.

· Cancerogenity categories· EPA (Environmental Protection Agency)None of the ingredients is listed.

· TLV (Threshold Limit Value established by ACGIH)None of the ingredients is listed.

· MAK (German Maximum Workplace Concentration)None of the ingredients is listed.

· NIOSH-Ca (National Institute for Occupational Safety and Health)None of the ingredients is listed.

· National regulations

· Information about limitation of use: Employment restrictions concerning young persons must be observed.· Chemical safety assessment: not required.

16 Other informationThis information is based on our present knowledge. However, this shall not constitute a guarantee for any specific product features and shallnot establish a legally valid contractual relationship.

· Relevant phrasesR36/38 Irritating to eyes and skin.

· Department issuing SDS:Hilti CorporationBusiness Unit ChemicalsQuality/Safety/EnvironmentFL-9494 Schaan / Liechtenstein

chemicals.hse@hilti.comTel.: +423 234 3004FAX.: +423 234 3462

· Date of preparation / last revision 06/30/2015 / 1· Abbreviations and acronyms:

ADR: Accord européen sur le transport des marchandises dangereuses par Route (European Agreement concerning the International Carriage of Dangerous Goods by Road)IMDG: International Maritime Code for Dangerous GoodsDOT: US Department of TransportationIATA: International Air Transport AssociationACGIH: American Conference of Governmental Industrial HygienistsEINECS: European Inventory of Existing Commercial Chemical SubstancesELINCS: European List of Notified Chemical SubstancesCAS: Chemical Abstracts Service (division of the American Chemical Society)NFPA: National Fire Protection Association (USA)PBT: Persistent, Bioaccumulative and ToxicvPvB: very Persistent and very Bioaccumulative

· * Data compared to the previous version altered. US

10

Hilti, Inc. 5400 South 122nd East Avenue

Tulsa, OK 74146

1-800-879-8000 www.hilti.com

September 24, 2015 To Whom It May Concern: Re: Hilti CP 618 Firestop Putty Stick – LEEDs Info. Item Number:

314721 The Hilti CP 618 is manufactured in France. The packaging for the CP 618 can be completely recycled. There is no post-consumer or post-industrial content in CP 618 and it cannot be recycled. The CP 618 does not contain any Rapidly Renewable Materials. The VOC content for CP 618 is 31.5 grams/liter. CP 618 is not regulated as a hazardous waste by the Federal EPA Standards. The regulations for the disposal of non-regulated industrial waste can vary from state to state and even city to city. For this reason, you should consult your local and state regulatory agencies for direction on disposal. Please feel free to contact me at (918) 872-3704 if you have questions. Sincerely,

Jerry Metcalf MPH, CHMM Sr. Manager, Safety/Environmental Manager Hilti Inc. 918 872 3704 jerry.metcalf@hilti.com Rev. Date: 9/24/15 The manufacturing plant location on this certificate has been provided for LEEDS reporting purposes only. It should never be used for Country of Origin certification or a representation of compliance/non-compliance with Buy American or Buy America requirements, as those requirements differ. The manufacturing plant location(s) identified on the certificate represent standard Hilti catalog products only. “Specially” produced non-catalog Hilti products may have differing manufacturing plant locations. Contact your Hilti representative in cases of “specially” produced products for a custom LEEDS certificates

11

Product Information

Hilti. Outperform. Outlast.Hilti, Inc. (U.S.) 1-800-879-8000 • www.us.hilti.com • en español 1-800-879-5000 • Hilti Firestop Systems Guide

IntroductionApplications and Products

Selector Guide

Through-PenetrationJoint

Reference D

ata

FM

R

FILL, VOID OR CAVITY MATERIALS CLASSIFIED BY

UNDERWRITERS LABORATORIES, INC.FOR USE IN TROUGH-PENETRATION

FIRESTOP SYSTEMS SEE UL FIRE RESISTANCE DIRECTORY

66Y7

FIRESTOP DEVICE FOR USE IN THROUGH-PENETRATION

FIRESTOP SYSTEMSSEE UL FIRE RESISTANCE DIRECTORY

5N76

Cast-In Firestop Devices (CP 680-P and CP 680-M)

For use in ■ Dust and fiber free environments such as hospitals, computer

centers and laboratories ■ Concrete floor assemblies rated up to 4 hours

Product description ■ A one-step cast-in firestop device for a variety of pipe materials

and diameters ■ Helps reduce labor costs and increase productivity ■ Ready-to-use out of the package ■ Internationally tested and approved by UL and FM ■ Reduces the chance of project delays due to failed inspections

Product features ■ Quick and simple installation ■ SpeedLine Alignment system promotes faster layout ■ QuickTurn System creates fast, simple vertical connections ■ Integrated moisture and smoke seal ■ Innovative adapter for metal deck applications

Installation and applications ■ Concrete floors from 2.5" (63 mm) thickness for either flat concrete

or concrete over metal deck CP 680-M: - Insulated and non-insulated metal pipes - EMT and electrical conduits - Cable bundles - Multiple pipes CP 680-P: Addresses all applications for CP 680-M as well as the following: - Plastic pipes such as PVC, CPVC, ABS, ENT and FRPP - Fresh and waste water pipes

Not suited for ■ Areas with high condensation ■ Outdoor areas ■ Wall applications

Technical Data CP 680-P and CP 680-MID Footprint Opening required thru metal deck2" 3-3/4" x 4-1/2" 3-1/2" diameter3" 4-3/4" x 5-5/8" 4-1/2" diameter4" 6-3/8" x 6-3/4" 5-1/2" diameter6" 9" x 9-1/2" 7-1/4" diameterExpansion temperature 392°F (200°C)Expansion rate 1:50 (unrestrained)

1:30 (Load expansion, Load = 20g/cm3)

Standard height 8"Temperature resistance Maximum 212°F (100°C)Color CP 680-P: red

CP 680-M: blackTested in accordance with• UL 1479 • ASTM E 814 • ASTM G21

Internationally tested and approved

CP 680-P in concrete over wood forms

CP 680-M in concrete over wood forms

CP 680-P over metal deck

CP 680-M over metal deck

Notice • Before handling, read Material Safety Data Sheet

and product label for safe usage and health information.

• Instructions below are general guidelines — always refer to the applicable drawing in the UL Fire Resistance Directory or Hilti Firestop Systems Guide for complete installation information

Instructions for use• Before pouring concrete, secure the cover cap in

place, thereby preventing the flow of concrete into the cast-in device

• Do not use for wall applications

Concrete floor with metal decking For concrete floor with metal decking applications use the correct size CP 680 Metal Deck Adapter for installed cast-in device and follow the illustrations.

Concrete floor

Installation optionFollow the illustrations if CP 680 has to be cut to slab thickness before installation, or when riser clamps are used.

Installation instructions

1 2

1 2

3 4

5 6

1 2

3 4

Visit fbcsystemcompatible.com. FBC™ is a trademark of the Lubrizol Corporation.

12

C E R T I F I C A T E O F C O M P L I A N C E

Certificate Number 20150626-R15431 Report Reference R15431

Issue Date 2015-06-26

William R. Carney, Director, North American Certification Programs UL LLC Any information and documentation involving UL Mark services are provided on behalf of UL LLC (UL) or any authorized licensee of UL. For questions, please contact a local UL Customer Service Representative at www.ul.com/contactus

Page 1 of 1

Issued to: Hilti, Inc,

5400 S 122ND East Ave Tulsa, OK 74146

This is to certify that

representative samples of

Firestop Devices

CP 680-M 2 in., CP 680-M 3 in., CP 680-M 4 in.,

CP 680-M 6 in., CP 680-P 2 in., CP 680-P 3 in.,

CP 680-P 4 in., CP 680-P 6 in., CP 681 and

CP 680-PX 2 in. and CP 680-PX 3 in.

for use Through-Penetration Firestop Systems as currently described in

the UL Fire Resistance Directory and the products Certified for Canada

Directory.

Have been investigated by UL in accordance with the Standard(s) indicated on this Certificate.

Standard(s) for Safety: ANSI/UL 1479, "Fire Tests of Through-Penetration Firestops."

CAN/ULC-S115 "Standard Method of Fire Tests of Firestop Systems." Additional Information: See the UL Online Certifications Directory at

www.ul.com/database for additional information

Only those products bearing the UL Classification Mark for the U.S. and Canada should be considered as being covered by UL's Classification and Follow-Up Service and meeting the appropriate U.S. and Canadian requirements.

The UL Classification Mark includes: the UL in a circle symbol: with the word “CLASSIFIED” (as shown); a control number (may be alphanumeric) assigned by UL; a statement to indicate the extent of UL’s evaluation of the product; and the product category name (product identity) as indicated in the appropriate UL Directory. The UL Classification Mark for Canada includes: the UL Classification

Mark for Canada: with the word “CLASSIFIED” (as shown); a control number (may be alphanumeric) assigned by UL; a statement to indicate the extent of UL’s evaluation of the product; and the product category name (product identity) in English, French, or English/French as indicated in the appropriate UL Directory. Look for the UL Classification Mark on the product.

13

Material Information Statement according to 1907/2006/EC, article 32

Version number 3

Revision: 26.11.2015

1 Identification of the substance/mixture and of the company/undertaking · Product identifier · Trade name: Hilti Firestop Block CFS-BL / CFS-BL P Hilti Firestop Plug CFS-PL Hilti Firestop Cable Collar CFS-CC / CFS-RCC / CFS-RCC EXT Hilti Firestop Module Box CFS-MB Hilti Firestop Cushion CFS-CU Hilti Firestop Board CP 675 Hilti Firestop Speed Sleeve CFS-SL Hilti Firestop Retrofit Sleeve CFS-SL RK Hilti Firestop Sleeve Kit CFS-SL SK Hilti Firestop Gangplate CFS-SL GP Hilti Firestop Cable Module CFS-T Hilti Firestop Filler Module CFS-T FB Hilti Firestop Plug Seal CFS-T RR

Hilti Firestop Plug Seal CFS-T RRS Hilti Firestop Wedge Seal CFS-T WD120 Hilti Firestop Cast-In Device CFS-CID Hilti Firestop Drop-In Device CFS-DID Hilti Foil Tapes CS-FT all Hilti Multifunctional Tapes CS-MFT all Hilti Joint Sealing Tapes CS-JST all Hilti Firestop Top Track Seal CFS-TTS CP 651N CP 653 CP 657 CP 658 CP 680 CP 681

· Application of the substance / the preparation: Construction chemicals Refer to Hilti product literature, technical data sheets, 3rd party published listings and national approvals for specific application information. For more details please contact your local Hilti organization through http://www.hilti.com. · Manufacturer/Supplier:

Hilti AG Feldkircherstr. 100 Postfach 333 FL-9494 Schaan Liechtenstein

Customer Service Phone +423 (0)844 84 84 85 Fax +423 (0)844 84 84 86

2 Other information

A Material Safety Data Sheet is not required due to the classification of these products as “articles” according to Regulation (EC) No. 1907/2006 of 18 December 2006 / 29CFR 1910.1200 (U.S.A.). Consequently, these products are exempted from CLP / OSHA Labeling and MSDS requirements. These data are based on our present knowledge. However, they shall not constitute a guarantee for any specific product features and shall not establish a legally valid contractual relationship. · Informing department:

chemicals.hse@hilti.com Tel.: +423 234 3004 FAX.: +423 234 3462

14

Hilti, Inc. 5400 South 122nd East Avenue

Tulsa, OK 74146

1-800-879-8000 www.hil ti.com

August 26, 2015 To Whom It May Concern: Re: The CP 680-M/P Cast-In Firestop Devices – LEED Information Item Numbers:

201599 203893 203894 203895 203896

201595 244244 244245 244246 244247

2088732 2088733 2088734 2088735 2088736

2088737 2088738 2088739 2088750 2088751

2088750 2088751 2088752 2088753

244248 244249 244250 244251 244252

244253 244254 244255 244260 244261

244262 244263 244264 244265 244266

244267

The Hilti CP 680-M/P Cast-In Firestop Devices are manufactured in Malaysia. The Hilti CP 680-M/P Cast-In Firestop Devices have a VOC content of 1.4 grams/liter. The steel parts of the CP680-M/P Cast-In Firestop Devices are recyclable. The post-consumer recycled steel content of the CP680-M/P Cast-In Firestop Device is 25%. The pre-consumer recycled steel content of the CP680-M/P Cast-In Firestop Device is not known. The plastic portion of the CP680-M/P Cast-In Firestop Device are recyclable. The recycled content of the plastic portion is not known. The CP 680-M/P Cast-In Firestop Devices do not contain any Rapidly Renewable Materials. The CP 680-M/P Cast-In Firestop Devices are not regulated as a hazardous waste by the Federal EPA Standards. The regulations for the disposal of non-regulated industrial waste can vary from state to state and even city to city. For this reason, you should consult your local and state regulatory agencies for direction on disposal. Please feel free to contact me at (918) 872-3704 if you have questions. Sincerely,

Jerry Metcalf MPH, CHMM Sr. Manager, Safety/ Environmental Hilti Inc. (918) 872 3704 jerry.metcalf@hilti.com Rev. 8/14/15 The manufacturing plant location on this certificate has been provided for LEEDS reporting purposes only. It should never be used for Country of Origin certification or a representation of compliance/non-compliance with Buy American or Buy America requirements, as those requirements differ. The manufacturing plant location(s) identified on the certificate represent standard Hilti catalog products only. “Specially” produced non-catalog Hilti products may have differing manufacturing plant locations. Contact your Hilti representative in cases of “specially” produced products for a custom LEEDS certificates.

15