Firefighter protective clothing

ANACONDA3rd category of Personal Protective Clothing

Type number: 787-1026

1

6/2019

2

Clothing image:

3

Clothing image:

Description of used materials and their technical parameters:

Garment features: This unique garment ANACONDA was developed to comply with firefighter´s healthprotection.Immediately after the end of an action, firefighters take off a contaminated outer shell with amembrane. They return to the station in the inner lining.Contaminated outer shell is inserted into special bags and transported to the laundry.

4

Description of used materials and their technical parameters:

Outer material: Fabric 1026GS1 – GA 001 DIAMOND Ultra/G-SPACER , 310 g/m2(93%Nomex®/5% Kevlar® / 2% PA antistatic, treatment SOFIGUARD® Performance)

Membrane: FR FABRIC 106/85, 160g/m2(36% Aramid / 28% PTFE/PU FR /36% Viscose FR)

Inner lining: art. 1772 – GA000 NOMEX® / VISCOSE, 220 g/m2(50% Aramid/ 50% Viscose FR)

Basic material construction which fulfills to requirements of EN 469:ANACONDA SET (EXTERNAL + INTERNAL) (outer material + membrane + inner lining)

Additional option (does not comply with requirements of EN 469) :It serves as a complementary protective clothing , for example after intervention to returnto the fire station when the outer shell got heavily soiled and contaminated.ANACONDA INTERNAL (inner lining)

Additional materials:

Reinforcement: BOROLON art. 81400, alternatively F 1321 Bl-SiPadding: NEOPREN ADI-CR (ADITEG)Cuff: 7115 Nomex/ViscoseVelcro: STAPSewings: N-tech 70Zipper: YKK a FIREFLY M60 Open End – OATSRed strap: 2008 VFL Nomex tape 2,5, rouge DGSC 30Red band: art. 1026 – NOMEX Diamond Ultra – 210 g/m2Sign (back): yellow heat transferMetal accessories: buttons, rings, bucklesBraces: DEVA braces

5

Reflective materials: 3M™ Scotchlite™ 9687 (yellow-silver-yellow)3M™ Scotchlite™ 9686 (orange-silver-orange)3M ™8987 – Yellow3M ™8940 - Silver

Design: jacket + trousers

Clothing impregnation:

• Top material is equipped by a sufficient impregnation Sofiguard® Performance thatsecures protection against water and chemicals. The producer of the material guaranteesmin. 25 cycles before any re-impregnation when the laundering instructions arefollowed.

• Impregnation efficiency in real conditions may differ from the measured laboratory results and is influenced by several factors.

• Keep your garment clean. • For recovery of the treatment we recommend additional drying in the tumbler at

temperature 70 °C for 15 minutes ! Perform the additional drying on closed garmentfrom the face side after each maintenance (washing + drying).

6

Clothing protective function and the complete list of harmonized standards used whendesigning this PPE:

This clothing is used as a firefighter's body protection during fire liquidation and related tasks,with the exception of interventions when chemicals or gases are present (it only allows foraccidental spraying with chemicals or flammable fluids).This clothing can be also used as a part of the total grounding system preventing combustibledischarges (except for the oxygen-enriched atmosphere and protection from voltage in grids).This protective clothing protect the upper, as well as lower body parts, including a neck, armsup to wrists, and legs up to ankles. In combination with other protective equipment, such as ahelmet, gloves, a face-guard, and boots, it provides firefighters with complex protection fromhazards stipulated in applicable standards:

EN ISO 13688:2014 - Protective Clothing – General Requirements(EN ISO 13688:2013)

EN 1149-5:2008 - Protective Clothing – Static Electricity Clothing(EN 1149-5:2008)

7

ČSN EN 469:2015/A1:2015/Opr. 1:2015 -Protective Clothing for Firefighters – Technical(EN 469:2005/A1:2006/AC:2006) Requirements for protective clothing for firefighters

Level of protection – achieved effectiveness of protective clothing

Heat transfer - flame level 2Heat transfer – radiation level 2Resistance to water penetration level 2Water vapour resistance level 2

level 1 – lower level of technical use (technical intervention – car accidents and so on)level 2 – higher level of technical use (fire fighting in closed place)

Clothing service life

Duration of the protective clothing using is not fixed. Expected service life is within the rangefrom 4 to 7 years in case of average utilization. It is protective clothing which means that it canbe damaged during some working activity. In such case the following steps have to be done:• Clean the clothing according to the instructions• Ensure skilled revision of the clothing by a responsible person (producer, skilled distributor, or

skilled person of a particular fire station)• In case of need repair it (to ensure safety the clothing should be repaired at the PRODUCER or

a trained person)• In case of excessive damage and failure of the protective properties of the clothing when the

repair is not worthwhile, we recommend to put out of use

8

Maintenance:

• We recommend delicate washing at 40 °C• All closures (zippers, press buttons, velcros, buttons, carabines) must be properly closed to avoid

abrasion• Before washing and drying is necessary to remove neoprene knee pads!• PH of washing bath must not be higher than 9. • Do not use detergents with bleaching effects.• Optimal level of machine loading is 2/3, with maximum possible water level and lower spinning

speeds. • If the garment has removable insert, always wash the outer parts separately from inserts. If inserts

are not soiled, remove them and wash just the outer parts to prevent unnecessary wear of moisture and thermal barrier.

• Do not use any softeners!

• Line dry is optimal• Using a tumbler dryer, dry at lower temperature. We recommend drying in two cycles (face and back

sides) 2 x 45 minutes. Inner lining only 1 x 45 min.• A dryer should be filled at 2/3 of its capacity. (f.e. for drum of 13 kg put dry garments with weight of

10 kg)• If the garment is damp, we recommend to hang it to dry• To recover the treatment we recommend additional drying at 70 °C for 15 minutes!! Perform the

additional drying on closed garment from the face side after each maintenance (washing + drying).

• Ironing is allowed at the maximum 110 °C, be careful when using steam.

9

• No bleaching is allowed.

• The clothing may be dry-cleaned using tetrachloroethylene, monofluortrichlormethane, and all solvents specified under the F symbol. The common cleaning procedures have no restriction.

• Professional wet cleaning. Ordinary cleaning procedures.

Finally we would like to draw your attention to a fact that NOMEX®material is as otherchemical materials sensitive to direct daylight. To eliminate mechanical and visual abrasionof the outer material of the garment it is essential to observe right laundering procedures,eventually timely done re-impregnation. We are absolutely convinced that the mostsensitive part at laundering is the time, the temperature and loading of the washing anddrying process. We can say that excessive temperature and over drying can result inexcessive shrinkage.We absolutely recommend keeping an evidence list of the clothing service and maintenance (Appendix 1 – see our web pages

Important warning:

Never wash and dry garment as a whole set!Maintain always outer shell with membrane separately from liningFollow label instructions placed inside the garment.

10

Decontamination (Disinfection) :

• Intervention clothing infected by biological material must be treated with hydrogenperoxide and peracetic acid-based concentrates activated during machine washing.

• Do not use chlorine-based products.• Recommended disinfection agents are suitable for white, as well as color textiles,

except wool and silk. Their utilization is in accordance with European microbicidestandards EN 1650 and EN 14476.

• Disinfection agents are effective at 40 °C and a longer washing cycle of at least 20minutes.

• The exact dosage will be specified by your chemicals supplier based on theintervention clothing types.

Washing and decontamination agents that can be used for intervention clothing are in the chart bellow:

Storage:

✓ Storage has no specific requirements✓ Protect the clothing from direct sunlight and UV radiation

Clothing protective packaging:

✓ PE bag, cardboard

For medium to highly contaminated protective garment by oils, petroleum, paints,and biological substances (proteins, blood etc.) we recommend to entrust the maintenanceto a professional laundry.

11

User notification:

• In compliance with EN 469 requirements, the lower and upper body parts, including aneck, arms to wrists, and legs to ankles are protected and covered by the clothing;however, the other body parts are not protected and other equipment items arenecessary to achieve the complete protection.

• In case of accidental soiling with a liquid chemical or flammable fluid when using in theenvironment with the excessive risk of exposure to fire and/or heat or when underexcessive heat load when heat is strongly felt on skin, it is necessary to immediatelyretreat and remove and clean the clothing, or decommission it if necessary.

• A person wearing protective clothing that dissipates static electricity charge must beproperly grounded. Resistance between such person and ground must be less than 108

W, by using, for example, proper footwear. The clothing must not be unfastened orremoved near flammable or explosive environment or when working with flammableor explosive agents. The clothing must not be used in the oxygen-enriched atmospherewithout a prior approval of a responsible safety technician. The clothing's staticelectricity protection properties could be affected by its wear, tear, washing, andsoiling. When in use, the static electricity dissipating protection clothing mustconstantly cover all materials that do not have such properties.

12