Finding modes of_a_cantilever_beam_in_nx7
-
Upload
laura-bendula -
Category
Education
-
view
505 -
download
0
Transcript of Finding modes of_a_cantilever_beam_in_nx7
![Page 1: Finding modes of_a_cantilever_beam_in_nx7](https://reader038.fdocuments.us/reader038/viewer/2022110308/55830397d8b42a121c8b4b80/html5/thumbnails/1.jpg)
Finding Modes of a Cantilever Beam in NX 7.0
Dr. Singh
![Page 2: Finding modes of_a_cantilever_beam_in_nx7](https://reader038.fdocuments.us/reader038/viewer/2022110308/55830397d8b42a121c8b4b80/html5/thumbnails/2.jpg)
Starting NX 7.0
Start>EAS Applications>Engineering Apps>NX 7.0.
![Page 3: Finding modes of_a_cantilever_beam_in_nx7](https://reader038.fdocuments.us/reader038/viewer/2022110308/55830397d8b42a121c8b4b80/html5/thumbnails/3.jpg)
New Model
New>Model. Change Units to Inches. New File Name>Name>’Beam.prt’ and Folder to your M-
drive. Click OK.
![Page 4: Finding modes of_a_cantilever_beam_in_nx7](https://reader038.fdocuments.us/reader038/viewer/2022110308/55830397d8b42a121c8b4b80/html5/thumbnails/4.jpg)
Sketching Geometry
Select the Sketch icon. Select Planar Face as the X-Z axis> OK. Green arrows should appear as shown above.
![Page 5: Finding modes of_a_cantilever_beam_in_nx7](https://reader038.fdocuments.us/reader038/viewer/2022110308/55830397d8b42a121c8b4b80/html5/thumbnails/5.jpg)
Sketching Geometry
Select the Rectangle tool. Sketch a rectangle at the origin with
width= 3” and height= .25”.
![Page 6: Finding modes of_a_cantilever_beam_in_nx7](https://reader038.fdocuments.us/reader038/viewer/2022110308/55830397d8b42a121c8b4b80/html5/thumbnails/6.jpg)
Extruding
Click the Finish Sketch icon. Click the Extrude icon. Select Curve>select the sketch. Direction>Reverse Direction. Limits>End Distance>24 in. Select OK.
![Page 7: Finding modes of_a_cantilever_beam_in_nx7](https://reader038.fdocuments.us/reader038/viewer/2022110308/55830397d8b42a121c8b4b80/html5/thumbnails/7.jpg)
Advanced Simulation
Start icon>Advanced Simulation.
![Page 8: Finding modes of_a_cantilever_beam_in_nx7](https://reader038.fdocuments.us/reader038/viewer/2022110308/55830397d8b42a121c8b4b80/html5/thumbnails/8.jpg)
Advanced Simulation
Simulation Navigator>Right-click beam.prt >New FEM and Simulation.
When New FEM and Simulation window appears, select OK.
![Page 9: Finding modes of_a_cantilever_beam_in_nx7](https://reader038.fdocuments.us/reader038/viewer/2022110308/55830397d8b42a121c8b4b80/html5/thumbnails/9.jpg)
Advanced Simulation
Change Solution Type to SEMODES 103- Response Simulation.
Click OK.
![Page 10: Finding modes of_a_cantilever_beam_in_nx7](https://reader038.fdocuments.us/reader038/viewer/2022110308/55830397d8b42a121c8b4b80/html5/thumbnails/10.jpg)
Meshing
Under Simulation File View, select beam_fem1 and click 3D Tetrahedral.
![Page 11: Finding modes of_a_cantilever_beam_in_nx7](https://reader038.fdocuments.us/reader038/viewer/2022110308/55830397d8b42a121c8b4b80/html5/thumbnails/11.jpg)
Meshing
Select Bodies: select the beam. Mesh Parameters>Element
Size>Automatic Element Size icon. Click OK.
![Page 12: Finding modes of_a_cantilever_beam_in_nx7](https://reader038.fdocuments.us/reader038/viewer/2022110308/55830397d8b42a121c8b4b80/html5/thumbnails/12.jpg)
Material Properties
Click on the Material Properties icon. Select the beam and Aluminum_6061. Click OK.
![Page 13: Finding modes of_a_cantilever_beam_in_nx7](https://reader038.fdocuments.us/reader038/viewer/2022110308/55830397d8b42a121c8b4b80/html5/thumbnails/13.jpg)
Advanced Simulation
Reselect beam_sim1.sim. Under Solution 1, right-click
Subcase- Dynamics and select Edit.
![Page 14: Finding modes of_a_cantilever_beam_in_nx7](https://reader038.fdocuments.us/reader038/viewer/2022110308/55830397d8b42a121c8b4b80/html5/thumbnails/14.jpg)
Advanced Simulation
Under Subcase- Dynamics>Output Request, click the Create Modeling Object icon.
![Page 15: Finding modes of_a_cantilever_beam_in_nx7](https://reader038.fdocuments.us/reader038/viewer/2022110308/55830397d8b42a121c8b4b80/html5/thumbnails/15.jpg)
Advanced Simulation
Under the Displacement tab, check the box next to Enable DISPLACEMENT Request.
Click OK.
![Page 16: Finding modes of_a_cantilever_beam_in_nx7](https://reader038.fdocuments.us/reader038/viewer/2022110308/55830397d8b42a121c8b4b80/html5/thumbnails/16.jpg)
Advanced Simulation
Under Lanczos Method, click the Create Modeling Object icon.
![Page 17: Finding modes of_a_cantilever_beam_in_nx7](https://reader038.fdocuments.us/reader038/viewer/2022110308/55830397d8b42a121c8b4b80/html5/thumbnails/17.jpg)
Advanced Simulation
Change the Number of Desired Modes to 10. Click OK.
![Page 18: Finding modes of_a_cantilever_beam_in_nx7](https://reader038.fdocuments.us/reader038/viewer/2022110308/55830397d8b42a121c8b4b80/html5/thumbnails/18.jpg)
Click Constraint Type pull-down bar and select Fixed Constraint.
Apply this to the left face of the beam. Click OK.
![Page 19: Finding modes of_a_cantilever_beam_in_nx7](https://reader038.fdocuments.us/reader038/viewer/2022110308/55830397d8b42a121c8b4b80/html5/thumbnails/19.jpg)
Advanced Simulation
Right-click Solution 1 and click Solve. When the window appears, click OK. Wait until the Analysis Job Monitor lists the solution as
‘Completed’.
![Page 20: Finding modes of_a_cantilever_beam_in_nx7](https://reader038.fdocuments.us/reader038/viewer/2022110308/55830397d8b42a121c8b4b80/html5/thumbnails/20.jpg)
Advanced Simulation
In the Post Processing Navigator, right-click Solution 1 and click Load.
Click the plus sign to expand the solution.
![Page 21: Finding modes of_a_cantilever_beam_in_nx7](https://reader038.fdocuments.us/reader038/viewer/2022110308/55830397d8b42a121c8b4b80/html5/thumbnails/21.jpg)
Results
Click on the plus sign next to each mode to expand.
Double click Displacement- Nodal to view displacement results.
Mode 1 Mode 2
Mode 5
![Page 22: Finding modes of_a_cantilever_beam_in_nx7](https://reader038.fdocuments.us/reader038/viewer/2022110308/55830397d8b42a121c8b4b80/html5/thumbnails/22.jpg)
Interpreting Results
Different types of modes can occur- for example, Mode 4 is a torsional mode.
Since we are only interested in bending modes, our first three modes will be Mode 1, Mode 2, and Mode 5.
Mode 4
![Page 23: Finding modes of_a_cantilever_beam_in_nx7](https://reader038.fdocuments.us/reader038/viewer/2022110308/55830397d8b42a121c8b4b80/html5/thumbnails/23.jpg)
Interpreting Results
If you are having difficulty distinguishing which type of mode is occurring, try rotating the beam to view from the constrained end.
Bending modes will displace up and down, lateral from side to side, and torsional in a twisting motion.
Bending Lateral Torsional
![Page 24: Finding modes of_a_cantilever_beam_in_nx7](https://reader038.fdocuments.us/reader038/viewer/2022110308/55830397d8b42a121c8b4b80/html5/thumbnails/24.jpg)
Interpreting Results
The values of Modes 1, 2, and 5 should approximately be:
Frequency (Hz)
Mode 1 14.09
Mode 2 88.19
Mode 5 247.1
![Page 25: Finding modes of_a_cantilever_beam_in_nx7](https://reader038.fdocuments.us/reader038/viewer/2022110308/55830397d8b42a121c8b4b80/html5/thumbnails/25.jpg)
Animation
To animate results, double-click Displacement-Nodal for any mode and click the Animation icon.
Adjust Synchronized frame delay and Number of frames.
Check the box next to Full-cycle to see the full modal cycle.
Click the Next Mode/Iteration icon to see the next mode.