NEISCONEISCO

Neisco For Modern Waters Systems Production

Head Office: Borg El Mohandessen 4/51,Post code 11371Rabaa El adawia Nasr City - Cairo - EgyptTel.: (+202) 240 18412 - 226 05695 - 240 51884Fax: (+202) 22629718

Factory: Badr industrial City zone 6/71 - Cairo - EgyptTel.: (+202) 286 41641 - 286 41642Fax: (+202) 28641132E-mail: info@neiscoegypt.comWebsite: www.neiscoegypt.com

NEISCO

Polyethylene is a thermoplastic comes from ethylene in monomer state. It is generally referred to as PE briefly in plastics industry.

FeaturesHigh density polyethylene is named as HDPE.HDPE has a high resistance against water and chemi-cals. HDPE has very good mechanical attributes, particularly, it has a high resistance to impact and tensile strength.

Usage- Potable water pipelines- pressure irrigation pipelines- treatment plant- cable Duct pipe- Sewage Pipelines- Solid waste drainage line

Advantages of Polyethylene Piping

• They have high flexibility features. Thus, they ensure ease of installation. Elongation at break is minimum 350%.

• They are not affected from underground movements, they do not break.

• They have high impact resistance and rapid crack propagation resistance.

• Since they have Low interior surface roughness, they ensure significant advantages while selecting diameter during project design.

• They do not have installation wastage thanks to the joining method.

• Black colored pipes are resistant to UV rays.

•They do not change odor and taste of water, there-fore, fit for health.

• It is not possible for plant and tree roots to penetrate inside the pipes.

HDPE Pipes

PE100 Minimum required strength MRS (MPa) Value 10PE100 Coefficient =1.25

Temperature (°C) Coefficient (fT)

1

0.87

0.74

20

30

40

Diameter (mm)

SDR26 - PN6 SDR17 - PN10 SDR11 - PN16Wall

ThicknessWeight Kg/m

Wall Thickness

Weight Kg/m

Wall Thickness

Weight Kg/m

20 2.0 0.11225 2.3 0.17132 2.0 0.187 3.0 0.27240 2.4 0.295 3.7 0.43050 2.0 0.314 3.0 0.453 4.6 0.66663 2.5 0.494 3.8 0.721 5.8 1.05075 2.9 0.675 4.5 1.020 6.8 1.47090 3.5 0.978 5.4 1.460 8.2 2.120

110 4.2 1.430 6.6 2.170 10 3.140

(mm)(mm)(mm)

PE100 Pipe Table

NEISCO introduces the Best Solutions for Water Networks serving the following Water Feeding:• Drainage. • Drip Irrigation Networks.• Water Treatment Stations.• Also Networks for Transfer of Gas and Petrol material through best Commercial Agents for Best International Producers. NEISCO After gaining a large market share in Egypt as COMER Italy Distributor on the year 2000 NEISCO, under license with COMER Italy, started to produce u.PVC pressure fittings and valves branded COMER by NEISCO. The NEISCO production is according to International Standards ISO 727, DIN 8063, EN 1452 and ISO 4422/3. The factory currently recruits more than 250 employees Management was trained in Italy by COMER NEISCO lately started to produce also PP Drippers to be inserted over the PE irrigation pipes known as “Inline Drippers” with self pressure control (pressure compensat-ed) and without self pressure control, together with anoth-er Online Dripper called “ Turbo Key “ with different Flow Rates “ 2. 4, 8 and 16 L/H “ for producing all elements that is in Irrigation Networks ( Dripping and Irrigation ). NEISCO is now working on completing additional product’s ranges expected to be ready on 2015/2016 for the Irrigation Networks, such as pipes, rigid PE drip lines (already in production), flat hoses drip lines, filters and accessories, on the aim to become a First Class Manufactur-er of complete Irrigation System and a leader Supplier of its products to MENA Market as well as of the Africa, Asia and Europe Markets. NEISCO has already an exceeding significant market share of the Egyptian u.PVC pressure Fittings and Valves market through a distribution network covering all major cities and NEISCO is already successfully exporting its products to over 26 Countries of Middle East, the Gulf and Africa.

In line Dripper - NON PC In line Dripper - PC

The IN LINE DRIPPER PC “COMER BY NEISCO” are compensating flow emitters with a silicone rubber discharge at different pressures. We produce IN LINE DRIPPER PC “COMER BY NEISCO” in two models:2,4 L/H. We recommended to use it in hilly areas or on terrains with different level of inclination.

Structure and features

• Unique flow regulating concept : a wide effective labyrinth, leading into the flow control chamber, where a sensitive floating diaphragm regulates and maintains a constant flow rate at variable inlet pressure • Operating pressure range 0.8 -3.0 bar• Resistant to chemicals and fertilizers commonly used in agriculture.

IN LINE DRIPPER PC 20mm

Operating pressure range 0.8 -3.0 bar

Diam

eter

(m

m)/

Flow

Rat

e

0.8 1 1.5 2 3 0.8 1 1.5 2 3

Act. Flow Rate (L/H) 1.7 2 2.1 2.15 2.2 3.7 3.9 4 4.2 4.2

IN LINE DRIPPER PC 16mm

Operating pressure range 0.8 -3.0 bar

The IN LINE DRIPPER “COMER BY NEISCO” are cylindrical dripper, designed with along, wide labyrinth. This configuration provides a turbulent water flow which minimizes formation of residues that may cause clogging. We produce “COMER BY NEISCO” flow emitters in four models:2,4 L/H

Structure and features• Large surface inlet filter • Outstanding clogging resistance for all flow rates • Operating pressure 1.0 bar• Resistant to chemicals and fertilizers commonly used in agriculture

IN LINE DRIPPER 16mm

*Recommended working pressure: 1.0 bar

IN LINE DRIPPER 20mm

*Recommended working pressure: 1.0 bar

Lateral length(m)

Diam

eter

(m

m)/

Flow

Rat

e0.3 0.33 0.5 0.75 1 0.3 0.33 0.5 0.75 1

Lateral length(m) 60 80 120 160 200 60 70 90 120 150

On Line Dripper - PC On Line Dripper - NON PC

Color FLOW (L/H)PRESSURE (bar)

0.8 1 1.5 2 2.5Black 2L/H 1.9 2.1 2.5 2.8 3.1

Blue 4L/H 3.8 4.2 4.5 4.8 5.1Brown 8L/H 7.8 8.2 9 9.5 10Green 16L/H 15.6 16.2 17 18.2 19.5

*Recommended working pressure: 1.0

The ON LINE DRIPPER “COMER BY NEISCO” are turbulent flow emitters with a removable top cap wich allows easy inspection and cleaning. We produce “COMER BY NEISCO” flow emitters in four models: 2, 4, 8, 16 L/H

Structure and features• Dripper can be opened to facilitate easy cleaning• Manufactured from virgin plastic for stable performance• Turbulent flow path with wide cross-sectional area ensures clog resistance• Extended outlet facilitates use of PE extension tube or vinyl tube• Regulating pressure range: 0.8-2.5 bar• Filtration requirement: 120 mesh, 130 micron

Technical data:

The ON LINE PC DRIPPER “COMER BY NEISCO” are an on line pressure compensating flow emitters with a removable tob cap and a silicone rubber diaphragm that regulates water discharge at different pressures. We produce “COMER BY NEISCO” compensating flow emitters in two models 4 , 8 L/H. We recommended to use it in hilly areas or on terrains with different level of inclination

Structure and features• Dripper can be opened to facilitate easy cleaning• Manufactured from virgin plastic for stable performance• Silicone rubber diaphragm ensures consistent performance for longer period• Narrow cross-shaped inlet acts as a filter• Optional anti-bug cap prevents intrusion of insects• Self-cleaning design ensures flushing at all times during operation• Wide operating pressure compensating range allows longer length of laterals• Regulating pressure range: 0.8-3 bar• Filtration requirement: 120 mesh, 130 micron

Color FLOW (L/H)PRESSURE (bar)

0.8 1 1.5 2 2.5 3

Blue4 L/H 3.8 4 4.1 4.15 4.2 4.3Red8 L/H 7.7 7.8 7.9 8 8.1 8.1

We test our product to better satisfy customer needs and to ensure the highest standards of quality and reliability

Technical data:

d X d D d L l Z g20 x 20 44 20 109 53 3 6225 x 25 52 25 121 59 3 9332 x 32 63 32 137 67 3 13140 x 40 76 40 167 82 3 27050 x 50 91 50 184 90 4 43063 x 63 107 63 214 105 4 67075 x 75 125 75 243 119 5 89490 x 90 150 90 307 151 5 1330

PP Compression

COUPLINGMANCHONوصلة

SO310

MATERIALS Body and nut are made of polypropylene copolymer (PP- B), conical Gaskets (special O-Rings) of NBR 70 shore (UNI 4920), clinching rings of acetalic resin. The threaded female offtakes from diametre 1¼” are reinforced with AISI 430 stainless steel ring

MAXIMUM WORKING TEMPERATUREPolypropylene: 100° C Acetalic resin: 80° C

MAXIMUM WORKING PRESSUREPN 16 from diametre 20 mm. up to 63 mm. PN 10 from diametre 75 mm. up to 110 mm. Reduced security factor for items with female thread 4”

STANDARDSCompression joints are complying with UNI9561, UNI 9562, DIN 8076-3 , ISO 14236, ISO 13460 Threads are complying with ISO 7/1 BS21

APPROVALSCOMER by NEISCO compression joints are suitable for alimentary fluids handling in accordance with the norms and prescriptions issued by the Ministry of Health Gazette n. 174 dated the 6nd of avril 2004 and are approved by: - JASWIC (Joint Acceptance Scheme for Water Installation Complements) in the Republic of South Africa.Neisco now is activity working on obtaining the most important approvals from other international Institutes.

ASSEMBLY INSTRUCTIONS Cut the pipe at 90° and chanfrin it. Insert at first the locking nut then the clinching ring, avoiding to push it too much forward on the pipe, the collar and O- ring.

Feed and push the body along the pipe axis. Before screwing the locking nut on the body, ascertain that the pipe hits the body inside step.

The full screwing of the locking nut can be made by hand till Ø 50 / 63 mm., whereas for bigger dimensions it is advisable to use a wrench

REDUCING COULING

MANCHON REDUITوصلة مخفضة

RS310

As our lip gasket enjoys special properties, no pre-lubrication procedure is required. this special properties give superior hydraulic performance in case of ovalized , scratched or even under sized pipes In addition, the special Conical Gasket O-Ring of the COMER by NEISCO compression Joints is granting the best performance in case of water hammer and/or water pressure peak inside the joint’s body.Comer by Neisco PP compression is a ready installed

fittings with non disassembling procedures or breakup . moreover bigger size pipe can be easily inserted due to the fact no hindrance between attaching the clamping and the pipe insertion procedure doesn't requires special tools to install the fittings with the pipeline

Description

NutClinching RingCollarLip GasketBODY

1

2

3

4

5

part

1

2

45

3

SO312

AD312

d x

d

G D

D

d

d

L

L

l

l

H Z g

g

20 x 1 /2" 44 20 88 53 18 35 3820 x 3/4" 44 20 88 53 18 35 4025 x 1/2" 52 25 94 59 18 35 5025 x 3/4" 52 25 95 59 18 36 5225 x 1" 52 25 97 59 20 38 5232 x 3/4" 63 32 102 67 18 35 7832 x 1" 63 32 106 67 20 39 8032 x 1 1/4" 63 32 106 67 22 41 9040 x 1" 76 40 127 82 22 45 14040 x 1 1/4" 76 40 129 82 24 47 15040 x 1 1/2" 76 40 129 82 24 47 16050 x 1 1/2" 91 50 140 90 24 50 23650 x 2" 91 50 141 90 26 51 25063 x 1 1/2" 107 63 154 105 24 49 38063 x 2" 107 63 160 105 26 55 39075 x 2" 125 75 179 119 26 60 73075 x 2 1/2" 125 75 178 119 26 59 75090 x 3" 150 90 213 151 28 62 774

d x G D d L l H Z g20 x 1/2" 44 20 89 53 18 18 5420 x 3/4" 44 20 90 53 18 19 6025 x 1/2" 52 25 95 58 18 18 6525 x 3/4" 52 25 99 58 18 18 6725 x 1" 52 25 104 58 20 20 7432 x 1/2" 63 32 105 67 18 19 9032 x 3/4" 63 32 106 67 18 19 9032 x 1" 63 32 123 67 20 19 9540 x 1 1/4" 76 40 128 82 22 24 20040 x 1 1/2" 76 40 128 82 27 19 22050 x 1 1/2" 91 50 139 90 27 22 25350 x 2" 91 50 145 90 29 22 27063 x 1 1/2" 107 63 155 105 27 22 42063 x 2" 107 63 160 105 29 26 44075 x 2" 125 75 174 119 29 26 78075 x 125 75 179 119 30 30 82090 x 3" 150 90 217 151 33 33 1000

2 1/2"

d x d x d D d L l L1 Z g20 x 20 x 20 44 20 130 53 65 24 10025 x 25 x 25 52 25 147 59 73 29 15032 x 32 x 32 63 32 168 67 84 34 23040 x 40 x 40 76 40 207 82 103 43 43050 x 50 x 50 91 50 234 90 117 54 68063 x 63 x 63 107 63 277 105 138 67 110075 x 75 x 75 125 75 319 119 159 81 190090 x 90 x 90 150 90 402 151 201 100 2200

d1xdxd1 D d D1 d1 L l L1 l1 Z g25 x 20 x 25 44 20 52 25 147 59 68 53 29 14532 x 25 x 32 52 25 63 32 168 67 78 59 34 23040 x 32 x 40 63 32 76 40 207 82 91 67 43 36050 x 32 x 50 63 32 91 50 234 90 98 67 54 55050 x 40 x 50 76 40 91 50 234 105 110 82 54 64063 x 50 x 63 91 50 107 63 277 127 127 90 67 940

TE341

d x G x d D d L l L1 H Z g20 x 1 2/ " x 20 44 20 130 53 45 18 24 8020 x 3 /4" x 20 44 20 130 53 45 18 24 8025 x 3/4" x 25 52 25 147 59 49 18 29 11125 x 1" x 25 52 25 147 59 51 22 29 11132 x 3/4" x 32 63 32 168 67 53 18 34 16832 x 1" x 32 63 32 168 67 56 22 34 16840 x 1 1/4" x 40 76 40 207 82 64 24 43 33050 x 1 1/2" x 50 91 50 234 90 73 26 54 53963 x 2" x 63 107 63 277 105 86 28 67 880

END CAPBOUCHONنهاية

ADAPTOR MALE THREADEDRACCORD MALE بداية خط سن خارجى

ADAPTOR FEMALE THREADEDRACCORD FEMALLE بداية خط سن داخلى

CA370

TR340

TE340

TR340

Tee 90°Te à 90° مشترك ٩٠°

Tee 90° reducedTe à 90° reduitمشترك مخفض

90° TEE with THREADED MALE OFFTAKE TE à 90° avec DERIV.FILETTEE MALE مشترك ذو سن خارجى ٩٠°

EL350

EL351

EL352

d x G x d D d L l L1 H Z g20 x 1/2" x 20 44 20 130 53 42 18 24 7820 x 3/4" x 20 44 20 130 53 42 18 24 7825 x 1/2" x 25 52 25 147 59 42 18 29 11425 x 3/4" x 25 52 25 147 59 47 18 29 11425 x 1" x 25 52 25 147 59 50 20 29 17232 x 3/4" x 32 63 32 168 67 51 18 34 19032 x 1" x 32 63 32 168 67 53 20 34 19040 x 1" x 40 76 40 207 82 53 20 43 33540 x 1 1 /4" x 40 76 40 207 82 61 22 43 33550 x 1 1/2" x 50 91 50 234 90 71 27 54 56563 x 2 x 63 107 63 277 105 85 29 67 87875 x 2 1/2 " x 75 125 75 319 119 95 30 81 144590 x 3" x 90 150 90 402 151 111 33 100 1700

d x d D d L l Z g20 x 20 44 20 65 53 12 7525 x 25 52 25 73 59 14 11032 x 32 63 32 84 67 17 15040 x 40 76 40 103 82 21 32050 x 50 91 50 117 90 27 48063 x 63 107 63 138 105 33 68075 x 75 125 75 159 119 40 132090 x 90 150 90 201 151 50 1600

d x G D d L l L1 H Z g20 x 1/2" 44 20 65 53 45 18 12 5420 x 3/4" 44 20 65 53 45 18 12 5425 x 1/2" 52 25 73 59 49 18 14 7625 x 3/4" 52 25 73 59 49 18 14 7625 x 1" 52 25 73 59 51 22 14 7632 x 1" 63 32 84 67 56 22 17 10040 x 1 1 /4" 76 40 103 82 64 24 21 22550 x 2" 91 50 117 90 75 28 27 34063 x 2" 107 63 138 105 86 28 33 560

d x G D d L l L1 H Z g20 x 1/2" 44 20 65 53 42 18 12 5420 x 3/4" 44 20 65 53 42 18 12 5425 x 3/4" 52 25 73 59 47 18 14 7425 x 1" 52 25 73 59 50 20 14 7432 x 3/4" 63 32 84 67 51 18 17 11132 x 1" 63 32 84 67 53 20 17 11140 x 1 1/4" 76 40 103 82 61 22 21 22550 x 1 1/2" 91 50 117 90 71 27 27 36863 x 2" 107 63 138 105 85 29 33 57075 x 2 1/2" 125 75 159 119 97 30 40 112090 x 3" 150 90 201 151 111 33 80 1440

75 x 21/2" 125 75 159 119 97 30 40 112090 x 3" 150 90 201 151 111 33 80 1440

TE342 90° TEE with THREADED FEMALE OFFTAKETE à 90° avec DERIV.FILETTEE FEMELLE مشترك ذو سن داخلى ٩٠°

90° ELBOW COUDE à 90° كوع ٩٠°

90° ELBOW W/THR.MALE OFFTAKE COUDE à 90° avec DERIV. FILETTEE MALE كوع ٩٠° ذو سن خارجى من طرف واحد

90° ELBOW W/THR. FEMALE OFFTAKE COUDE à 90° avec DERIV. FILETTEE FEMELLE كوع ٩٠° ذو سن داخلى من طرف واحد

Material: Body U.V. stabilized polypropylene Bolts galvanized Steel / Stainless SteelOring NBR / EPDM

Working Pressure:20° C: 10 bars up to D. 160 6 bars above Suitable for drinking water and alimentary fluids

Saddles Notes:d x G Weight (g)

20 x 1/2" 60.2 225 x 1/2" 60.2 225 x 3/4" 57.7 232 x 1/2" 71.1 232 x 3/4" 68.6 240 x 1/2" 103 240 x 3/4" 101 240 x 1" 106 250 x 1/2" 204 450 x3/4" 210 450 x 1" 213 450 x 1 1/4" 224 463 x 1/2" 235 463 x 3/4" 231 463 x 1" 231 463 x 1 1/4" 220 463 x 1 1/2" 239 475 x 1/2" 262 475 x 3/4" 272 475 x 1" 264 475 x 1 1/4" 283 475 x 1 1/2" 300 475 x 2" 313 490 x 1/2" 350 490 x 3/4" 341 490 x 1" 341 490 x 1 1/4" 343 490 x 1 1/2" 361 490 x 2" 363 4110 x 1/2" 505 4110 x 3/4" 499 4110 x 1" 503 4110 x 1 1/4" 507 4110 x 1 1/2" 546 4110 x 2" 522 4110 x 3" 578 4125 x 3/4" 508 4125 x 1" 507 4125 x 1 1/4" 509 4125 x 1 1/2" 509 4125 x 2" 518 4125 x 3" 836 4140 x 3/ 4" 748 6140 x 1" 753 6140 x 1 1/4" 779 6140 x 1 1/2" 784 6140 x 2" 813 6160 x 3/4" 792 6160 x 1" 788 6160 x 1 1/4" 794 6160 x 1 1/2" 826 6160 x 2" 798 6160 x 3" 1097 6160 x 4" 1111 6

Bolts

CLAMP SADDLES IN PP FOR POLYETHYLENE AND PVC PIPES/ WITH REINFORCING RING

COLLIERS DE PRISE EN PP POUR TUYAUX EN PE ET PVC/AVEC ANNEAU DE RENFORCEMENT

ركاب بولي بروبلين النابيب البولي ايثلين وال بي في سي

مع الحلقة المعدنية/

SA350 SA351