Fibre Cement Profiled Sheets - Briarwood Products Ltd...Fibre cement profiled sheets are an ideal...
Transcript of Fibre Cement Profiled Sheets - Briarwood Products Ltd...Fibre cement profiled sheets are an ideal...
www.briarwoodproducts.co.uk
Fibre Cement Profiled Sheets
Fibre cement profiled sheets are an ideal cladding for Agricultural, Industrial, Commercial and Domestic buildings
EUROSIX Fibre cement profiled sheets have many advantages over alternative roof coverings which will benefit the life expectancy and efficient use of your building, Benefits include vapour permeability (natural ability for sheets to ‘breath’) thus significantly reducing the possibility of condensation, excellent acoustic insulation which reduces noise within the building, completely weatherproof roof covering and maintenance free after fixing.
EUROSIX fibre cement profiled sheets are maintenance free, will not suffer from rust, rot or corrosion and are expected to last well in excess of 30 years minimum. EUROSIX sheeting is often fixed to roofs where the building may contain a very aggressive atmosphere (chemicals, dampness, heat etc) and because of all the natural benefits enjoyed by EUROSIX they will exceed expectations and life expectancy of most alternative products available on the market today, and has done for 100 years.
The full range of EUROSIX fibre cement sheeting is reinforced with strategically placed polypropylene strips which are fully integrated along each corrugation of every sheet.Natural Grey is the standard finish of the EUROSIX fibre cement sheet and fittings but a range of colours are available from Briarwoods stock in either a Matt surface finish (colour wash) which reduces sun glare and reflection from the roof or a further range of BS standard colours with a top surface ‘baked’ on paint system and specified often by local authorities when matching in to surrounding buildings or landscapes.
Briarwood hold the largest range of Natural Grey, Meadowscape and standard Painted colours in both sheets and fittings along with Spaced sheets and Ventilation systems with no restriction on any sheets sizes or range of fittings if required outside the natural grey colour range.
EUROSIX is manufactured under QS ISO 9002 and fully covered by CE Certification and BBA approved.
Please turn over to view the complete EUROSIX range of fibre cement sheets accessories
8 9
www.briarwoodproducts.co.uk
Fibre Cement Profiled Sheets
Reinforced Sheeting
Reinforced Spaced SheetingEfficient ventilation is important in any livestock building as it supports animal welfare by reducing moisture levels which can carry bacteria and disease.
EUROSIX Sheet Lengths & Weights
Metric Imperial Dry Weight (KG)1525 5’ 24.801675 5’6 27.291830 6’ 29.812000 6’6 32.582130 7’ 34.702290 7’6 37.312440 8’ 39.752600 8’6 42.352740 9’ 44.642900 9’6 47.273050 10’ 49.70
EUROSIX Spaced Sheet Lengths & Weights
Metric Imperial Dry Weight (KG)1525 5’ 22.801675 5’6 25.051830 6’ 27.452000 6’6 30.002130 7’ 31.952290 7’6 36.602440 8’ 37.312600 8’6 39.002740 9’ 41.402900 9’6 43.503050 10’ 45.75
Net Cover 1016mm
Nominal Pitch
146.5mm
Nominal Width 1086mm
Overall Depth
54mm
Thickness 6.8mm
EUROSIX Sheet Lengths & Weights
Metric Imperial
1525 5’ 1675 5’61830 6’ 2000 6’62130 7’ 2290 7’62440 8’ 2600 8’62740 9’ 2900 9’63050 10’
Length Weight KG
1525 24.801675 27.291830 29.812000 32.582130 34.702290 37.312440 39.752600 42.352740 44.632900 47.243050 49.70
This illustration shows the location of the strategically
placed polypropylene reinforcing strips which are
inserted into each corrugation of our EUROSIX Fibre
Cement Sheeting.
Reinforced Sheeting
Briarwood Catalogue 2014 Page 5
page 5-6 profile data.indd 8 19/03/2014 17:33:50
Net Cover 1016mm
Nominal Pitch
146.5mm
Nominal Width 1086mm
Overall Depth
54mm
Thickness 6.8mm
EUROSIX Sheet Lengths & Weights
Metric Imperial
1525 5’ 1675 5’61830 6’ 2000 6’62130 7’ 2290 7’62440 8’ 2600 8’62740 9’ 2900 9’63050 10’
Length Weight KG
1525 24.801675 27.291830 29.812000 32.582130 34.702290 37.312440 39.752600 42.352740 44.632900 47.243050 49.70
This illustration shows the location of the strategically
placed polypropylene reinforcing strips which are
inserted into each corrugation of our EUROSIX Fibre
Cement Sheeting.
Reinforced Sheeting
Briarwood Catalogue 2014 Page 5
page 5-6 profile data.indd 8 19/03/2014 17:33:50
Nominal Pitch
146.5mm
Sheet Width 1000mm
Thickness 6.8mm
Reinforced Spaced Sheeting(Provides efficient natural ventilation)
Metric Imperial
1525 5’ 1675 5’61830 6’ 2000 6’62130 7’ 2290 7’62440 8’ 2600 8’62740 9’ 2900 9’63050 10’
EUROSIX Spaced Sheet Lengths & Weights
Length Weight KG
1525 22.801675 25.051830 27.452000 30.002130 31.952290 36.602440 37.312600 39.002740 41.402900 43.503050 45.75
Briarwood Catalogue 2014 Page 6
page 5-6 profile data.indd 9 19/03/2014 17:33:54
Nominal Pitch
146.5mm
Sheet Width 1000mm
Thickness 6.8mm
Reinforced Spaced Sheeting(Provides efficient natural ventilation)
Metric Imperial
1525 5’ 1675 5’61830 6’ 2000 6’62130 7’ 2290 7’62440 8’ 2600 8’62740 9’ 2900 9’63050 10’
EUROSIX Spaced Sheet Lengths & Weights
Length Weight KG
1525 22.801675 25.051830 27.452000 30.002130 31.952290 36.602440 37.312600 39.002740 41.402900 43.503050 45.75
Briarwood Catalogue 2014 Page 6
page 5-6 profile data.indd 9 19/03/2014 17:33:54
Nominal Pitch
146.5mm
Sheet Width 1000mm
Thickness 6.8mm
Reinforced Spaced Sheeting(Provides efficient natural ventilation)
Metric Imperial
1525 5’ 1675 5’61830 6’ 2000 6’62130 7’ 2290 7’62440 8’ 2600 8’62740 9’ 2900 9’63050 10’
EUROSIX Spaced Sheet Lengths & Weights
Length Weight KG
1525 22.801675 25.051830 27.452000 30.002130 31.952290 36.602440 37.312600 39.002740 41.402900 43.503050 45.75
Briarwood Catalogue 2014 Page 6
page 5-6 profile data.indd 9 19/03/2014 17:33:54
Net Cover 1016mm
Nominal Pitch
146.5mm
Nominal Width 1086mm
Overall Depth
54mm
Thickness 6.8mm
Nominal Pitch
146.5mm
Sheet Width 1000mm
Thickness 6.8mm
10 11
www.briarwoodproducts.co.uk
Close Fitting Ridge
Ventilated Ridge 900mm Girth
150mm MAX
Clear Opening175mm
200mm
Fixing Point
Timber Or Steel Purlin
150mm MAX
Clear Opening
Fixing Point
Timber Or Steel Purlin
200mm
175mm
Briarwood Catalogue 2014 Page 7
page 7 cf and vent.indd 10 21/03/2014 08:52:18
Available in 750mm Girth
To suit roof pitches: 12.5 & 15 Degrees only
Available in 900mm Girth
To suit roof pitches: 5, 7.5, 10, 12.5, 15, 17.5, 20, 22.5 Degrees
Available in 1800mm* Girth
To suit roof pitches: 10, 12.5, 15, 17.5, 22.5 Degrees
* 1800mm Fragile – Further reinforcement is required under the ridge to conform to HSG33
Available in 750mm Girth
To suit roof pitches 12.5 & 15 Degrees only
Available in 900mm Girth
To suit pitches: 5, 7.5, 10, 12.5, 15, 17.5, 20, 22.5 Degrees
Available in 1800mm* Girth
To suit pitches: 10, 12.5, 15, 17.5, 22.5 Degrees
* 1800mm Fragile – Further reinforcement is required under the ridge to conform to HSG33 Vent opening dimension 100mm (height) x 732.5mm (maximum width)
These ridge fittings meet the requirements of HSG-33 Health and Safety Roof Work Manual.
Please note any ridges fitted to the old conventional method DO NOT meet the requirements of HSG-33.
These ridge fittings meet the requirements of HSG-33 Health and Safety Roof Work Manual.
Please note any ridges fitted to the old conventional method DO NOT meet the requirements of HSG-33.
Ventilation Ridge
Ventilated Ridge 900mm Girth
150mm MAX
Clear Opening175mm
200mm
Fixing Point
Timber Or Steel Purlin
150mm MAX
Clear Opening
Fixing Point
Timber Or Steel Purlin
200mm
175mm
Briarwood Catalogue 2014 Page 7
page 7 cf and vent.indd 10 21/03/2014 08:52:18
Girth750mm, 900mm or 1800mm
Pitch Angle 305mmRadius
Girth750mm, 900mm or 1800mm
Pitch Angle 305mmRadius
12 13
www.briarwoodproducts.co.uk
Two Piece Adjustable Ridges Close Fitting
Two Piece Adjustable Ridges Ventilated
150mm MAX
100mmFixing Point
Clear Opening
Timber Or Steel Purlin
MAX
Clear Opening
Fixing Point
Timber Or Steel Purlin
100mm
Briarwood Catalogue 2014 Page 8
page 8 cf adj.indd 11 19/03/2014 17:35:04
400mm - 600mm
250mm Approx
Fixing Point 300mm MAX
Timber or Steel Purlins
Fixing Point
100mm
150mm MAX
Clear Opening
Timber or Steel Purlins
Page 9
page 9 pw opr deiagram.indd 12 20/03/2014 15:56:34
150mm MAX
100mmFixing Point
Clear Opening
Timber Or Steel Purlin
MAX
Clear Opening
Fixing Point
Timber Or Steel Purlin
100mm
Briarwood Catalogue 2014 Page 8
page 8 cf adj.indd 11 19/03/2014 17:35:04
These ridge fittings meet the requirements of HSG-33 Health and Safety Roof Work Manual.
Please note any ridges fitted to the old conventional method DO NOT meet the requirements of HSG-33
These ridge fittings meet the requirements of HSG-33 Health and Safety Roof Work Manual.
Please note any ridges fitted to the old conventional method DO NOT meet the requirements of HSG-33.
One piece Disc Finials, Diamond Finials or two piece Hooded Finials are a good option used to close the
gable end detail of any EUROSIX two piece ridge fittings.
Two Piece Adjustable Ridges Plain Wing
Disc Diamond Hooded
Finials
14 15
400mm - 600mm
250mm Approx
Fixing Point 300mm MAX
Timber or Steel Purlins
Fixing Point
100mm
150mm MAX
Clear Opening
Timber or Steel Purlins
Page 9
page 9 pw opr deiagram.indd 12 20/03/2014 15:56:34
400mm - 600mm
250mm Approx
Fixing Point 300mm MAX
Timber or Steel Purlins
Fixing Point
100mm
150mm MAX
Clear Opening
Timber or Steel Purlins
Page 9
page 9 pw opr deiagram.indd 12 20/03/2014 15:56:34
www.briarwoodproducts.co.uk
Cranked Barge Boards Barge Boards
Plain Wing Cranked Barge Board
For use when a one piece ridge is fitted (finials are required when 2 piece ridges are fixed)Available in 200x200mm wing at 1300mm & 2200mm GirthAvailable in 300x300mm wing at 1300mm Girth OnlyTo Suit Roof Pitches:5, 7.5, 10, 12.5, 15, 17.5, 22.5 Degrees
Roll Top Cranked Barge Board
For use when a one piece ridge is fitted (finials are required when 2 piece ridges are fixed)Available in 200x200mm wing at 1300mm & 2200mm GirthTo Suit Roof Pitches:5, 7.5, 10, 12.5, 15, 17.5, 22.5 Degrees
Plain Wing Barge Board
Used to close the verge at gable ends and also vertical claddingAvailable in 200x200mm or 300x300mm WingLength: 1830mm, 2440mm or 3050mm
Roll Top Barge Board
Used to close the verge at gable endsAvailable in 200x200mm WingLength: 1830mm, 2440mm or 3050mmSocket detail provides cover on overlap
Vergeline Barge Board
Used to close the verge atgable endsLength: 1830mm, 2440mm or 3050mmMin Lap: 150mmSocket detail provides cover on overlapThis fitment is handed, please state hand when ordering. This image shows right hand piece.
Girth 1300mm or 2200mm
359mmRadius
359mmRadius
359mmRadius
Girth 1300mm
Pitch Angle
Pitch Angle
Pitch Angle
Girth 1300mm or 2200mm
200mm Or
300mm
200mm
305mm
Page 11
page 11 crk bb.indd 14 21/03/2014 08:54:06
200mm Or
300mm
200mm Or
300mm
200mm
200m
m
305mm
305mm
150mm
30mm
Page 10
20/03/2014 15:59:43
Vergeline Cranked Barge Board
For use when a one piece ridge is fitted (finials are required when 2 piece ridges are fixed)Available in 1300mm Girth OnlyTo Suit Roof Pitches:10, 12.5, 15, 17.5 22.5 Degrees
Girth 1300mm or 2200mm
359mmRadius
359mmRadius
359mmRadius
Girth 1300mm
Pitch Angle
Pitch Angle
Pitch Angle
Girth 1300mm or 2200mm
200mm Or
300mm
200mm
305mm
Page 11
page 11 crk bb.indd 14 21/03/2014 08:54:06
16 17
www.briarwoodproducts.co.uk
Apron-Eaves Accessories Movement Joints
Apron Flashing
Used at the junction detail where vertical and standard pitched roofs meet
Net Cover: 1016mm
Eave Filler
Closes corrugation at eaves of single skin cladding
Net Cover: 1016mm
Eave Closure
Closes corrugation at eaves of single skin and insulated cladding system
Net Cover: 1016mm
190m
m
54
260mm 140mm
265mm
150mm
mm051
Page 13
75mm54mm
20/03/2014 08:19:08
Movement Joint
Used to allow a movement\expansion break in larger buildings. Where a movement joint is required, the full EUROSIX sheet beneath it should be cut along the centre of its valley with a space of 25mm to 30mm.
Recommended spacing for Movement Joints are:-• Buildings with a length of 45 metres or less do not need a
Movement Joint.• Buildings with a length of 45 metres – 75 metres require one run of Movement Joints.• Another Movement Joint will be required every additional
30 metres.• Movement Joints require a minimum end lap of 150mm.• Movement Joints are fixed directly into purlins (not
through sheets)• Fixings should go through the centre point of the
Movement Joints at each Purlin position.
Cranked Movement Joint
Fixed on the ridge detail to overlap the top end detail of a straight Movement Joint. Fixings specification is the same as straight movement joints.
Movement Joint 2 piece Ridge
This is a flexible 2 piece movement joint ridge section which adjusts to fit at the crown of a duo-pitch roof.
Movement Joint Stop End
Used to close the open end of a straight Movement Joint at the eaves.
18 19
www.briarwoodproducts.co.uk
Open Protected Ridge
ApplicationApplication 1Application
1
23
4
1
Reinforced Sheets & GRP Rooflights
2
Close Fitting, Ventilated & Two Piece Ridges
Disc, Diamond, & Hooded Finials
3
4Plain Wing, Roll Top& Vergeline Barge Boards
6
5
5Cranked Plain Wing, Roll Top & Vergeline Barge Boards
6Apron Flashing, Eave Closure & Eave Fillers
Briarwood Catalogue 2014 Page 14
page 14 3d building.indd 17 21/03/2014 10:28:01
Application
1
23
4
1
Reinforced Sheets & GRP Rooflights
2
Close Fitting, Ventilated & Two Piece Ridges
Disc, Diamond, & Hooded Finials
3
4Plain Wing, Roll Top& Vergeline Barge Boards
6
5
5Cranked Plain Wing, Roll Top & Vergeline Barge Boards
6Apron Flashing, Eave Closure & Eave Fillers
Briarwood Catalogue 2014 Page 14
page 14 3d building.indd 17 21/03/2014 10:28:01
Application
1
23
4
1
Reinforced Sheets & GRP Rooflights
2
Close Fitting, Ventilated & Two Piece Ridges
Disc, Diamond, & Hooded Finials
3
4Plain Wing, Roll Top& Vergeline Barge Boards
6
5
5Cranked Plain Wing, Roll Top & Vergeline Barge Boards
6Apron Flashing, Eave Closure & Eave Fillers
Briarwood Catalogue 2014 Page 14
page 14 3d building.indd 17 21/03/2014 10:28:01
Application
1
23
4
1
Reinforced Sheets & GRP Rooflights
2
Close Fitting, Ventilated & Two Piece Ridges
Disc, Diamond, & Hooded Finials
3
4Plain Wing, Roll Top& Vergeline Barge Boards
6
5
5Cranked Plain Wing, Roll Top & Vergeline Barge Boards
6Apron Flashing, Eave Closure & Eave Fillers
Briarwood Catalogue 2014 Page 14
page 14 3d building.indd 17 21/03/2014 10:28:01
1 Ridges:Close Fitting, Ventilated & Two Piece
2 Sheets:Reinforced & GRP Rooflights
3 Finials:Disc, Diamond & Hooded
4 Barge Boards:Plain Wing, Roll Top & Vergeline
5 Cranked Plain Barge Boards:Wing, Roll Top & Vergeline
6 Aprons & Eaves:Flashing, Closures & Fillers
1
5
32
6
4400mm - 600mm
250mm Approx
Fixing Point 300mm MAX
Timber or Steel Purlins
Fixing Point
100mm
150mm MAX
Clear Opening
Timber or Steel Purlins
Page 9
page 9 pw opr deiagram.indd 12 20/03/2014 15:56:34
These ridge fittings meet the requirements of HSG-33 Health and Safety Roof Work Manual.
Please note any ridges fitted to the old conventional method DO NOT meet the requirements of HSG-33
Intermediate purlins positioned along the fixing line can be used with the Open Ridge system to secure
the fixing through sheeting.
Efficient ventilation is important in any livestock building as it supports animal welfare by reducing
moisture levels which can carry bacteria and disease.
20 21