FiberTronic -Pigtail and Patch cords
-
Upload
lawrence-kim -
Category
Documents
-
view
187 -
download
3
Transcript of FiberTronic -Pigtail and Patch cords
FiberTronic Pigtail and Patch Cords Specification
Fiber Type:
1. Sheath PVC or LSZH.
2. Loose or Tight Buffer.
3. Corning, YOFC, J-Fiber or OFS Fiber.
4. G652D,G657A1, G657A2,OM1,OM2,OM3,OM4
5. Pigtail and Patch cord 0.9mm, 1.2mm, 1.6mm, 2.0mm or 3.0mm.
Cable Color:
1 2 3 4 5 6 7 8 9 10 11 12
Blue Orange Green Brown Gray White Red Black Yellow Erica violet Pink Aqua
Product Specifications:
Fiber Mode SM / MM
Connector Type SC / LC / ST / FC / MU / MTP / MPO / E2000 / SMA / MTRJ
Cable OD 0.9mm / 1.2mm / 1.6mm / 2.0mm / 3.0mm
End face type UPC / APC /PC
Return Loss (dB) ≥ 55 dB / ≥ 65 dB / ≥ 35dB
Insertion Loss (dB) ≤ 0.25 dB
Substitutability (dB) ≤ 0.20 dB
Repeatability (dB) ≤ 0.1 dB
Operating Temperature (℃) -40 ~ +75
Storage Temperature (℃) -40 ~ +85
Operating wavelength(nm) 850 / 1300 / 1310 / 1550
Test parameters and pictures:
Insertion Loss≤0.25 dB UPC Return Loss≥55 dB / APC ≥65 dB
End face of the grade::::
A class end face(Referring to chart#1 end face grading standards).
Technical Parameters::::
Compliance with IEC-61754 standard.
Compliance with Telcordia-GR-326-COR standard.
Meet the ROSH standard.
Packaging requirements::::
Neutral packing,Specific reference to the following chart
Packing of 12 Color Pigtail Packing of Each Patch Cords
Inner Packing with Partition Inner Packing with Waterproof Bag
Carton with PVC Film
Fiber optic connector end schematic
`
Chart#1
1.1.1.1. A + grade end face of the standard ::::
Defect category The core (region A) Zone B Region C Region D Remarks
Scratch Not allowed Not allowed Not allowed Not allowed Region D, does not
allow cracks, suitable
for standard test patch
cord.
Spots Not allowed Not allowed Not allowed Not allowed
Layer Not allowed
2222 A grade end face of the standard ::::
Defect
category
The core
(region A) Region B Region C Region D
Remarks
Scratch Not allowed Not
allowed
Allow a width ≤0.5μm,
length ≤50μm
(1 Piece).
Allow a width ≤1μm,
length ≤125μm
(1 Piece)
Region D, does
not allow cracks,
suitable for High
Quality Patch
cord. Spots Not allowed Not
allowed
Allow diameter ≤0.5μm
(2 Pieces)
Allow diameter
≤1μm
(2 Pieces)
Layer Not allowed
3.B grade end face of the standard ::::
Defect
category
The core
(region A)
Region B Region C Region D
Remarks
Scratch Not allowed
Allow a width
≤1μm, strip length
≤125μm
(1 Piece)
Allow a width
≤1μm, strip
length ≤125μm
(2 Piece)
Allow a width
≤2μm, strip length
≤125μm
(2 Piece)
Region B + Region
C defect ≤5
Pieces, Region D,
does not allow
cracks, suitable
for standard patch
cord.
Spots Not allowed Allow a diameter
≤1μm(1 Piece)
Allow a diameter
≤1μm(2 Piece)
Allow a diameter
≤2μm(2 Piece)
Layer Allow glue width between the region C and region D ≤2μm; layer is less than
30% the length of the circumference of the fiber end face
Note: 1μm equal to 400 times the microscope at 9 "on the display image is 0.8mm, 2μm after amplification is
1.6mm.
(Region A)Fiber core(10μmWithin)
(Region B )Fiber end(10μm~30μm)
(Region D)Ceramic ferrule surface
Scratch
Spots
(Region C)Fiber end(30μm~125μm)