www.superioraluminum.comwww.superioraluminum.com

Elegance, Strength, and Dependability

FiberglassColumns

Strength - Fiberglass columns can beused as load bearing structural elements in entrances, covered walkways, lobbies, colonnades, balconies, and other structures, inside or outside.

Easy Installation - Cut the columnsto size and slip on the caps and bases. Easy to follow assembly and installation instructions are located on the back cover and packaged with each column.

Complete Range of Sizes -Superior Aluminum offers a wide range of sizes and lengths to fit almost any appli-cation. Refer to the Dimensions and Load Data charts for available sizes.

Finish - For outdoor installations, thecolumns must be protected. A good quality alkyd or oil based primer and paint are recommended. Paint should be applied with a brush. Spray painting is not recommended. No special preparation is required, and once painted, the columns will not deteriorate, even under severe long-term weathering.

Superior fiberglass columns are shaped as they were in Ancient Greece, stretching upward from a strong base to a graceful taper at the smooth top. Whether round, fluted, or square, our fiberglass columns are specially constructed for all types of decorative and load-bearing installations, and have architecturally correct proportions and projections. The Greeks used the word “entasis” to describe their columns… you will call them “beautiful.” They are perfect for indoor and outdoor applications and ideal for both residential and commercial use.

Whether it’s for new construction or remodeling, beautiful Superior fiberglass columns are the low-cost way to add a touch of elegance and detail to your architectural designs that will last a lifetime. Our fiberglass columns are manufactured from high density, highly advanced fiberglass polymers that resist impact damage, and are virtually maintenance-free

Durability - Unlike wood, fiberglasscolumns will not rot, split, or warp, and are more impact resistant than wood. And, of course, termites hate them.

Elegance, Strength, and Dependability

Round and Square

Fiberglass Columns

Round Column Square Tapered Square RecessedColumn Panel Column

SPECIALTY COLUMNS

* Round columns should be trimmed only in non-tapered area of column to assure proper fit to base. Caps are viewed from top. Bases are viewed from bottom.

Dimensions & Load DataRound Columns

www.superioraluminum.com 11

Standard Ionic Scamozzi Temple Corinthian

Standard Attic

CAPS & BASES

Round smooth and round fluted columns are complemented by matching classic caps and bas-es, including the Standard, Ionic, Scamozzi, Temple, and Corinthian caps and Standard and Attic bases (shown above). Square columns are also provided with a matching classic cap and base (shown below).

Square Cap Square Base

Nominal Actual Cap Cap Base Base Square SquareWidth Width Width Height Width Height Column Column

Q R S T U V

6” 5-1/2” 8” 1-15/16” 8-1/2” 3-1/4” 9’ 5,000

8” 7-1/2” 10-1/8” 2-3/8” 10-3/8” 4-1/4” 8, 9, 10’ 10,000

10” 9-1/2” 12-3/4” 3” 13” 5-1/4” 8. 9, 10’ 10,000

12” 11-1/2” 15-7/8” 3-3/8” 15-1/4” 6” 8, 9, 10, 12’ 10,000

Square Cap Square Base

Square Standard Load Column Lengths Lbs. (in feet)

Column Extends Column ExtendsThrough Cap Through Base

Dimensions & Load DataSquare Columns

(For Non-Tapered and Recessed

Panel Columns)

www.superioraluminum.com 12

Easy Assembly and Installation InstructionsRound Columns with Standard Caps1. Slide the standard cap over the column neck until it rests against the column shoulder bead.

2. The column neck should protrude 1/16” above the cap. Trim evenly withan abrasive saw (if required). Be sure to wear safety glasses.

3. Measure the required length or opening where the column is to be used. The column should be slightly longer for a snug fit.

4. Trim the bottom of the column to achieve the desired overall height. Be sure to wear safety glasses. Be certain the saw-cut (top & bot-tom) is even so the load is evenly distributed around the column circumference. If necessary, use a rasp to even it out.

5. Position the cap and base on the column and temporarily stand the column in position, then plumb with a level. With a pencil, mark the exact mounting position around the cap and base.

6. Securing the Column to the Structure*A. Using Construction Adhesive: One method of

securing the column to the structure is to apply construc-

tion adhesive to the top of the column and the bottom trimmed surface of the

column with the column lying down.

B. Using “L” Brackets: Another method of attaching the column to the structure is the use of L-shaped brackets at the bottom of column. To secure the “L” brackets to the column,

drill holes through the column walls and use through bolts. Do not use screws.

7. Set the column in place, then remove jacks or props.

8. Caulk between the rim area of the base and column with a high quality paintable caulk. Clean the column surface with a damp cloth. An alkyd or oil based primer and paint are recommended. Paint should be applied with a brush. Spray painting is not recommended.

Round Columns with Ornamental Caps1. Trim off the top of the column neck to the shoulder bead with an abrasive saw. Trim evenly around the column circumference. Be sure to wear safety glasses.

2. Measure the required length or opening where the column is to be used. The column should be slightly longer for a snug fit.

3. Apply construction adhesive around the lower round surface of the cap, then position the cap on the column.

4. Measure the overall required length measuring from the top of the cap to the bottom end of the column. Trim from the bottom end of the column only. Be certain the saw-cut is even so the load is distributed evenly around the column circumference. Be sure to wear safety glasses.

5. Position the base on the column, then temporarily stand the column in position and plumb with a level. With the cap and base in proper position, mark the exact mounting location with a pencil.

6.* Next, lay the column down and apply construction adhesive to the top of the ornamental cap and on the bottom trimmed surface of the column. Another method of securing the column top in place is by drilling holes on opposite sides at an angle through the cap. Then, attach the column to the structure with screws. Do not over tighten.

Another method of attaching the bottom of the column to the structure is the use of L-shaped brackets attached to the bottom of column. To secure the “L” brackets to thecolumn, drill holes through the column walls and use through bolts. Do not use screws.

7. Set the column in its permanent position, then remove jack or props.

8. Caulk between the rim area of the base and column with a high quality paintable caulk. Clean the column surface with a damp cloth. An alkyd or oil based primer and paint are recommended. Paint should be applied with a brush. Spray painting is not recommended.

Square Columnswith Cap & Base1. Measure the required length or opening where the column is to be used. Using an abrasive saw, the column should be trimmed slightly longer for a snug fit. Be sure to wear safety glasses.

NOTE: Generally the bottom section of the column is sawed off to fit the opening. Trim evenly so the weight is evenly distributed around the column. However, depending upon your preference, a maximum of 1-3/4” can be trimmed off the top, if desired.

2. Position the cap and base on the column and temporarily stand the column in position, then plumb with a level. With a pencil, mark the exact mounting position around the top neck of the column and the base.

3. Next, lay the column down and apply construction adhesive to the top and bottom load bearing surfaces of the column. See “Installation Note” below.

4. Install the cap and base and set the column in place, then remove jacks or props.

5. With the cap temporary pushed up, draw a pencil line around the bottom surface of the cap. Allow the cap to slide down, then apply construction adhesive to the top of cap, (or upper mounting surface), and to the upper neck of the column. Position the cap up and press it firmly in place.

6. Draw a pencil line around the column at the top of the base, then slide the base up and apply construction adhesive around the column below the pencil line. Slide the base down to its normal floor position.

7. Caulk with a high quality paintable caulk between the base and column and the cap and column.

8. Clean the column surface with a damp cloth. An alkyd or oil based primer and paint are recommended. Paint should be applied with a brush. Spray painting is not recommended.

*INSTALLATION NOTE: CHECK APPLICABLE STATE, LOCAL, AND FEDERAL BUILDING CODES FOR SPECIFIC INSTALLATION AND FASTENING REQUIREMENTS APPLICABLE TO THE PROJECT.

Installation Tip – Column may be trimmed with an abrasive saw, hacksaw, or fine-toothed handsaw. A rasp can be used to even it out.

1/16"

“L” Brackets

Trim off column neck

Adhesive

Measure from top of cap

“L” Brackets

www.superioraluminum.com 13