FE599 Lever Lock Installation Instructions

Keypad

Key

Cover

Coverscrews (2)

Baseplate

Latch

Strike

Latch/strikescrews (4) AA Batteries (4)

Lever

Pin wrench

OR

Alternate Faceplate

Important Information

Lock Programming Code

six (6) digits

User Code A

four (4) digits

User Code B

four (4) digits

Web Support: part2.schlage.com

Customer Service: (877) 288-7707

1 Locate Programming Code and Preset User CodesThe programming code and the preset user codes are printed on the yellow stickers located on the back of the keypad and on the installation sheet that came in the box. Write these codes in the space provided on the first page.

OR O OU!

Without these user codes, you can get locked out.Si no cuenta con estos códigos de usuario, es posible que no pueda abrir.Vous ne pouvez entrer sans déverrouiller à l'aide des codes d'utilisateur.

Preset Codes

Códigos preajustados

Préréglage des codes

Programming CodeCódigo de programaciónCode de programmation

User CodesCódigos de usuarioCodes utilisateur

Lock ModelModelo de la cerraduraModèle de serrure

Serial NumberNúmero de serieNuméro de série

Alternate FaceplateChapa frontal alternaPlateau à trous alternatif

2

Install LockInstalación de la cerradura Installer le verrou1

ORO

OU

2 ³⁄₄

180°

2³⁄₄” (70 mm)2³⁄₈” (60 mm)

Choose Faceplate to Match DoorEscoja la placa delantera para emparejar la puertaChoisir la têtière pour égaler la porte

OR

O

OU

4

4

3

ORO

OU

4

5

!

6 Caution Precaución Mise en garde

7

3

TopParte superiorHaut

TopParte superiorHaut

Match arrowsLas flechas deben quedar alineadasAligner les flèches

2³⁄₈” (60 mm)OR O OU2³⁄₄” (70 mm)

2¹⁄₈” (53 mm)HoleAgujeroTrou

5¹⁄₂” (140 mm)Minimum

MínimoMinimum

(2)

Installation InstructionsInstrucciones de instalaciónNotice d'installation

Check DimensionsRevise las dimensionesVérifier les dimensions

2Prog Code XXXXXXUser Code A XXXXUser Code B XXXX

(FCC ID: P2GXXXXX)XXXXXSN XXXXXXXXX

Prog C

ode XX

XX

XX

User C

ode A X

XX

XU

ser Code B

XX

XX (FC

C ID

: P2G

XX

XX

X)

XX

XX

XS

N X

XX

XX

XX

XX

Prog Code XXXXXXUser Code A XXXXUser Code B XXXX

(FCC ID: P2GXXXXX)XXXXXSN XXXXXXXXX

2C\,” (60 mm)OR2C\v” (60 mm)

2Z\,” (53 mm)Hole

2 Check Door DimensionsIf your door does not match the dimensions shown, go to www.part2.schlage.com for instructions on how to prepare your door.

3 Install Strike Into Frame

4 If Necessary, Change Latch FaceplateCheck edge of door to determine the type of faceplate required.

OR

5

OR

Door Jamb Door Jamb

6P5

15-8

04Re

v. 08

/07

¹⁄₈" ¹⁄₄"

0

¹⁄₈"–¹⁄₄"(3–6 mm)

5 Install LatchLatch must be flipped so that bevel faces toward door jamb.

6 Remove Sticker from back of Lock

8 Adjust Hands-free PostThe hands-free post is the threaded stud on back of lock. It’s purpose (in step 10) is to attach the lock and baseplate together so that the lock will hold itself on the door.

Hands free post may need to be adjusted with a screwdriver to the dimensions shown below.

Z\,”- Z\v”(3 mm - 6 mm)

Hold keypadagainst door

Adjust with screwdriver so screw extends beyond door edge.

7 Install the KeypadFeed the cable under latch assembly as shown below. Then slide the tailpiece through the hole as shown below.

Hands-freepost

9

10 Slide Baseplate onto Door over Hands-free postHands-free post should lock plate against door surface. If hands-free post does not lock plate onto door, see step 8 for adjustment.

Hands-free post

Feed Cable through BaseplateFeed the cable through the hole as shown below. DO NOT connect the cable at this point.

12 Install Batteries and Battery Cover

11 Connect the CableSnap the connectors together.

13 Install Cover and LeverSee step 14 on the next page to verify that the lever is handed correctly to match your door. If the lever does not snap into place easily, you may have to tap the lever with a hammer using a piece of wood to cushion it. Be careful not to damage the finish of the lever.

!Tuck wires into open space on baseplate.Be careful not to pinch any wires betweencover and baseplate.

Check Handing of Lever14

IncorrectSee steps below to

change lever handing

CorrectGo to step 15

To Change Lever Handing

a b

c

d

16

15

Test Outside Entry (When Door is Locked)When you press your User Code (four numbers) on the keypad, the door will unlock for 5 seconds, allowing entry.

Test Locking and Unlocking from the Interior

Green light(indicates unlocked)

Red light(indicates locked)

To Unlock, Press Button To Lock, Press Button

Programming Code XXXXXXUser Code A xxxxUser Code B xxxx

S/N x-xxxxxxxxModel BE369

Press (four numbers) Green flash = unlock

! Test with door open to avoid possibly being locked out!

Verify that latch retracts when lever is turned

on keypad

! Test with door open to avoid possibly being locked out!

Follow the directions on document to continue setup.

17 This portion of the setup is complete.

Document 2 is located at part2.schlage.com.

©2010 Schlage Lock CompanyFE599 Online IS Rev. 03/10-b

FCC NoticeThis device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications to this equipment not expressly approved by Schlage could void the user’s authority to operate the equipment.

FCC ID: P2GFE599 IC: 7954A-FE599

PATENT NOTICESchlage® products and those of its subsidiary companies and licensees may be covered by both issued and pending U.S. and foreign patents, copyrights and trademarks. Manufactured items are covered by one or more of the following patents:

507071551525585308131539514455931935598726564086356831275715717

576541257694725809816581608658202905881590591891662863476297725

652337565333366540274658142668025466905773692631971434777159424

D372417D372854D406056D406528D426452D428324D450558D457048D457049

D458829D467155D472788D487388D520331D520332D537702D541620D543435