FE55 Mirage 2000D interior S.A. - Eduard · E8 For further detail sets look for eduard 49 555...
Transcript of FE55 Mirage 2000D interior S.A. - Eduard · E8 For further detail sets look for eduard 49 555...
FE556
FE556 1/48 scale detail set for kit •sada detailù pro model 1/48 Kinetic Kinetic
Mirage 2000D interior S.A.
SYMETRICAL ASSEMBLYSYMETRICKÁ MONTÁZ ´ ́
REMOVEODSTRANIT
OPTIONVOLBA?
REPLACENAHRADIT
BENDOHNOUT
GRINDOBROUSIT
1/3
ORIGINAL KIT PARTSPÙVODNÍ DÍLY STAVEBNICE
PHOTO-ETCHED PARTSLEPTANÉ DÍLY
PARTS TO BE REMOVEDDÍLY K ODSTRANÌNÍ
FILLTMELIT
eduard
24
27
26
29
A1 A2
24
27
26
A1 A2
29
8
7
9
10
E4
17
5
4
6
1632
43
20
37
30
3
1
2
31
28
4038
39
41
25
22
E425
2215
E7
HOW TO MAKE THE RELIEF ONOPPOSITE - REVERSE -
OF THE PLATE
! plastic ! plastic
HOW TO MAKE THE RELIEF ONOPPOSITE - REVERSE -
OF THE PLATE
3336
42
A1. A2
E8
eduardFor further detail sets look for 49 555 Mirage 2000B interior S.A.(not included in this set)
eduardFor further detail sets look for 49 557 Mirage 2000N interior S.A.(not included in this set)
eduardFor further detail sets look for 48 693 Mirage 2000B/D/N exterior(not included in this set)
STEP 1
=
D18
12
11
36
14
14
33
35
13 13
21
C28, C29, D8
18
19
23
34
STEP 1
=
12
11
36
14
14
33
18
19
23
34D18
35
13 13
21
D8, E2, E3
Made in Czech RepublicEduard M.A. © 2011 www.eduard.com
FE5562/3
2. Do not inadvertently place etched componets on an unwanted surface. Attempts to remove will result in damage to your part.
2. Nepokládejte samolepící díly na volné plochy. Pokud je omylem pøilepíte, pøi pokusu o odlepení dojde k poškození dílu.
3. Do not touch the adhesive areas of the etched components.
3. Nesahejte na èásti dílù, na kterých je naneseno lepidlo.1. Separate the etched components from their frames on the protective paper. Removal from the paper is done only after separation of the parts from the frames.
1.Samolepící díly oddìlujte od rámeèku na podkladovém papíøe. Po oddìlení je sejmìte z krycího papíru.
4. Hold the parts by the edges, or at areas free of adhesive.
4. Samolepící díly berte za hrany nebo za èásti, na kterých není nanesené lepidlo.
5. Lightly place the component in the desired location and position. Adjust as required. The component will by permanently affixed when pressed onto its intended location, its location can be adjusted.
5. Díl lehce položte do pozice, ve které má být nalepen. Upravte pøesnou pozici a pøimáèknìte. Díl dokonale pøilne až po pøimáèknutí, pøed pøimáèknutím lze dílem opatrnì manipulovat.
PARTS WITH GLUE DÍLY OPATØENÉ LEPIDLEM
FE5563/3