FDC-L10 - FEELUX€¦ · FDC-L10 DC 0/1 - 10V LED INTERFACE FDC-L10 This type of electronic...
Transcript of FDC-L10 - FEELUX€¦ · FDC-L10 DC 0/1 - 10V LED INTERFACE FDC-L10 This type of electronic...
12V/24V
FDC-L10 INPUTOUTPUTSIGNAL
DC 12V,12V LED Max.50W,DC 0 - 10V or DC 1 - 10V DIMMER
DC 24V24V LED Max.100W
DC 0/1 - 10V LED INTERFACE
80 mm(3 3/16”)
DC 12V
DC 24VFDC-L10
DC 12V LED Max.50W
DC 24V LED Max.100W
INPUT OUTPUT
1 9/16”(40 mm)
11/16”(17 mm)
Max.25/32”(20mm)
Max.25/32”(20 mm)
Min.1/32”(1 mm)
Max.1/2”(42 mm)
WARNING
CAUTION- RISK OF FIRE (ATTENTION – RISQUE D’INCENDIE)- INHERENTLY PROTECTED (PROTECTION INHÉRENTE)- USE ONLY WITH CLASS 2 POWER UNIT (UTILISER SEULEMENT AVEC LA CLASSE 2 BLOC D’ALIMENTATION)- SUITABLE FOR DAMP LOCATIONS (CONVIENT AUX EMPLACEMENTS HUMIDES)- SUITABLE FOR UNDER-CABINET MOUNT (PEUT ÊTRE FIXÉ SOUS UNE ARMOIRE)- LED light may be bright and intense enough to cause injury to human eyes. The customer should never look directly into the LED light.
Head Office : 624-8, Seogu-ri, Gwangjeok-myeon,Yangju-si, Gyeonggi-do, Korea (www.feelux.com)
U.S.A Office : 3000 Northwoods Parkway, Suite115 Norcross, GA 30071 U.S.A (www.feelux.com)
FDC-L10DC 0/1 - 10V LED INTERFACE
FDC-L10
This type of electronic interface is an exclusively designed for dimming 12V/24V LED Lamps. With Pulse Width Modulators (PWM)technology, it is suitable for constant voltage (12V/24V) lamps with connected in parallel. It have short circuit protection, abnormalover current protection, after protection must cut off the power, and check-up the load, make sure the load is in rating load, thenconnect the power, the interface will be right. And it also has input polarity reverse protection.
LED INTERFACEFDC-L10 INPUT
OUTPUTSIGNAL
DC 12V,12V LED Max.50W,DC 0 - 10V or DC 1 - 10V DIMMER
DC 24V24V LED Max.100W
LED INTERFACE
LEDCONVERTER
WIRE STRIP24-18AWG
(0.3-0.75 ㎟) WIRE STRIP24-18AWG
(0.3-0.75 ㎟)LED CONVERTER
0/1-10V DIMMERLED LAMP
0/1-10VDIMMER
LED LAMP
LED INTERFACEFDC-L10
This type of electronic interface is an exclusively designed for dimming 12V/24V LED Lamps. With Pulse Width Modulators (PWM)technology, it is suitable for constant voltage (12V/24V) lamps with connected in parallel. It have short circuit protection, abnormalover current protection, after protection must cut off the power, and check-up the load, make sure the load is in rating load, thenconnect the power, the interface will be right. And it also has input polarity reverse protection.
DIP Switch Mode Setting
ON
1 2
If you will use DC 0-10V signal dimmer, Please No.1 set “OFF mode”.If you will use DC 1-10V signal dimmer, Please No.1 set “ON mode”
If you will turn off LED output when input signal voltage is low than 0.8V, Please No.2 set “OFF mode”.If you will turn on LED output when input signal voltage is low than 0.8V, Please No.2 set “ON mode”