w w w . i n a t e c k . com

FD2002USB3.0 Dual SATA HDD Docking StationWith Offline Clone Function

Plug&Play, Hotswap, no need drive installation

- 2 -

FD2002 HDD Docking StationInstruction Manual

Top slot-loading desgin, tool free to insert HDD, convenience to operate Support data copy and clone between dual HDDs Compatible with SATA revision 1/2/3 (1.5/3.0/6.0 Gbps) driver Super Speed USB 3.0 transfer rate up to 5Gbps

Compatible operating system environments: Windows XP/Vista/7/8/8.1, Mac OS 9.0 and higher

Packing list:

FD2002 Docking Station x1 USB3.0 Data Cable x1 Instruction Manual x1

I. FD2002 Introduction This product support data copy and clone between dual HDDs. Meanwhile, it adopts USB3.0 (Super Speed) with date transfer rate up to 5Gbps and SATA3 (6Gbps) and backward compatible with earlier versions as well. This excellent transmission performance and good compatibility is convenient for data exchange and perfectly suitable for the men who need to batch processing and clone data at some certain places, such as film and television production, Backup & processing IT data, Schools batch processing data etc.

DC Power Adapter x1

Product schematic

① LED indicator② Clone Button③ SATA HDD Slot

④ USB3.0⑤ DC-IN Jack⑥ Power Switch

- 3 -

II. Technical data Product name USB3.0 Dual SATA HDD Docking Station with Offline Clone Function

Product type Inateck FD2002

Weight 410g

Colour Black

Supported drives 2.5”/3.5” SATA I/II/III HDD/SSD

Interface USB3.0

Material Plastic

Hot Plug, Plug & Play Supported

Licences CE, FCC

Measurements 450mm length x 109mm width x 60mm height

Operation environment Storage: -40 to 70 °C; Operation: 5 to 55 °C

Supported operating systems Windows XP/Vista/7/8/8.1, Mac OS 9.0 and higher

III. Hard drive installation steps a. Connect DC power adapter with docking stationb. Connect docking station with computer by USB cablec. Insert HDD into slot of docking station correctly.

Power on, lower right comer of computer will have a mobile hardware prompt after device recognized, disk management will also have one.

d.

IV. Instruction for the removal of drives Please note: Before the removal of the data storage device, please stop all data access

and transfer to the device, so that the storage can be normally removed. Forced removal

may lead to damage or loss of crucial data. To prevent any data loss, please strictly follow the steps for removal below!

a. Removal from Windows systems: Right click on the hardware or USB device removal symbol in the status bar, click on the periphery to be removed. When the system notification reading “the device can now be safely removed.”

shows up, you can remove the data storage.

- 4 -

Another way to remove the data storage is through the device manager

(“Computer” -> “Device Manager” -> “Drives” -> Click on “Remove” for the drive to be removed, so that the drive can be detached safely.

b. Removal from Macintosh systems: Please choose the symbol for “Portable

drives / devices”, choose the menu function “Remove” from the drop down menuby right clicking onto the symbol. You may also drag the “Portable device” to the

rubbish bin. Now, the device can be safely removed.

- 5 -

V. Offline Duplicate Functiona. This product supports offline duplicate function which can clone the HDD directly

without connecting to computers by USB port.b. Insert the HDDs to "A"&"B", A is the HDD to be cloned, B is the target HDD to

cloning, HDDs capacity requires B≥Ac. Start cloning: Press "Clone" button on the product about 3 seconds, when release

the button “The LED indicator of 100% will light up”, and quickly click "Clone", then it start cloning. Indicator lights (25%, 50%, 75%, 100%) flash up in turn during cloning, and whole lights on after completion. Cloning is done.

VI. Sleep Mode

a. After finishing cloning HDDs under offline duplicate mode, product goes to sleep mode if there were no operations in 30min and HDDs stop running. Power Indicator light flashes up every 3 seconds, and other progress indicator lights and disk light still work, that means clone is done and goes to sleep mode without any operations. HDDs will wake up again to stand-by mode by press clone button shortly.

b. When USB3.0 port connects to computer, product goes to sleep mode if there were no reading or writing on hard disk in 30min and HDDs stop running. Power Indicator light flashes up every 3 seconds, and disk light keeps working. LED lights flash up when computer reads and writes again.

VII. Partition and FormattingIf your HDD has been partitioned, please connect directly with docking station to use. It will be showed “New Disk” in computer.If not, in the premise of system can correctly identify HDD, you can use the partition and formatting program come with system to do it, or third-party software (such as Fdisk, DM, PQ Magic, etc.) to do it. (The following comes to Win7 system partition and format for example.)

- 6 -

1. Right-select the computer, select the ‘management’ into Computer Management and select ‘Disk Management’, then right-click the disk name in the left region, select Initialize the disk, then right-click in the right area of the disk, select set up new simple volume.

2. In the New Simple Volume Wizard, click Next, according to the desired partition resize disk partition size, and select Next, specify the disk drive letter, Click Next, select the file system, enter the volume label, and select Disk formatting way, click Next, click Finish, the disk will be formatted. Above, the operation can be repeated according to disk size.

a. Unable to start cloning: Please check whether the actual capacity of B disk is higher than A disk (B≥A), otherwise it won’t work when A disk’s actual capacity is higher than B disk’s. (B<A )

b. Indicator light stops flashing up during offline duplicating: it might because of disk bad sectors so that data couldn’t be cloned as usual. It’s better to change a good disk.

c. After cloning, the rest capacity of B disk is showed and operated via “Computer management - Storage - Disk management”.Why over 2TB hard disk couldn’t be identified by USB? Because the maximum capacity of hard disk which Windows XP can supports is 2TB and couldn’t be identified by system if over 2TB. It only supports after upgrading the operating system above Vista (64 bit) version and we suggest changing hard disk into a GPT disk partition, or the operating system will not support over 2 TB disk partitions.

d.

Please make sure that B hard disk data can be covered before cloning data. Because once you start cloning, B hard disk partition methods and data are completely cloned as A hard disk. Our company does NOT undertake any responsibility for data or economy loss which could bring by damaged data.

e.

- 7 -

VIII. FAQ

3. After operation finished, open My Computer, it will apper the ‘New Disk’ except the local disk, indicated that it connect computer successfully.

w.inateck.comEmail: support@inateck.com

Tel: 0341-5199 8407