20M H20 DIVABLE CONFIG

Acoustic Tube for Covert Monitoring

CONNECTING EARMUFFS

Helmet Clip

C4OPS Control Box

Peltor/ Sordin Headset Adaptor P/N: CA0015-01

Earmuff

NOTE: Prior to diving, disconnect all other radio adaptors and attach diving caps.

Tighten battery cover

Acoustic Tube

Helmet Clip

Headband

C4OPS Maritime Headset Config (P/N: SHS0003-17)

The C4OPS System configured with the C4OPS Maritime Headset Config (P/N: SHS0003-17) and MBITR 10 pin radio adaptor (P/N: CA0035-00) is 20m immersible.

CONFIGURATION NOTICE: This document contains operational informa-tion related to the Silynx C4OPS® Headset. The information contained here-in is for the operation and support of the C4OPS® Headset.

PROPRIETARY NOTICE: This document contains information that is pro-prietary to Silynx Communications, Inc. It is furnished solely for operation and support purposes and is not provided for reprocurement purposes. All reprocurement and manufacturing rights are expressly reserved by Silynx Communications, Inc. and no such use may be made of this document, either directly or indirectly, without the prior written consent of an authorized official of Silynx Communications, Inc.

SILYNX COMMUNICATIONS, INC PUBLISHED AND CONFIDENTIAL WORK Fast Guide - DOC-USM000011 - Rev 06, April 2015 ALL RIGHTS RESERVED COPYRIGHT:

www.silynxcom.com 1.866.325.1731 | customersupport@silynxcom.com

9901 Belward Campus Drive Suite 150 Rockville, MD 20850

FAST GUIDE

MBITR 10 pin radio adaptor (P/N: CA0035-00)

Micro C4OPS External Battery Compartment (P/N: CA0234-00)

C4OPSMICRO C4OPS

MBITR 10 pin radio adaptor (P/N: CA0035-00)

FAST GUIDEC4OPS

PROTECTION FROM WITHIN

SETTING UP OPERATING C4OPS® BASIC FUNCTIONS

(+) Volume

(-) Volume

Secondary PTT

“Pairing Successful”“Pairing Activated”

Beeps 30 sec

NOTE: If “Pairing Failed” repeat the steps above.

(-) Hear Thru Low Sensitivity/ Hear Thru Off

(+) Hear Thru High Sensitivity

(1) Press & hold

(2) Press & hold pairing keys 3 sec

PAIRING DUAL WIRELESS PTT [DWPTT]

HEAR THRU LEVEL VOLUME LEVEL

Off/ On/ Volume Level

High Sensitivity

Low Sensitivity/ Hear Thru Off

NOTE: In windy conditions reduce “Hear Thru”

CHANNEL SELECTION VOICE PROMPT VOLUME LEVEL

EXTRAS

(2) Press & hold 3 sec to confirm (2) (+) Volume

(2) (-) Volume(2) Press & hold 3 sec to confirm

(1) Press until you hear “Channel Selection”

(1) Press until you hear “Voice Prompt Level”

Press & hold 3 sec “Extras”

In high noise, such as aircraft/vehicles, you may hear whistling. Press (-) until the sound disappears. If the problem continues, reinsert the ear buds and make sure you pass the sealing test.

TROUBLESHOOTING:

MOUNTING THE CONTROL BOX

Molle Clip

Zipties

Zipties

*1.5V AA Lithium battery NOTE: No battery needed if using MBITR side connector.

Peltor/ Sordin Headset Adaptor Maritime Headset Config

Secondary Radio Lead

Connect

Intercom Cable Adaptor

Connect

Attach

Tighten

(1) Connect

C4OPS Control Box

C4OPS In Ear Headset

Headband Boom Mic

Ops Core Chinstrap Boom Mic

Basic In Ear Headset (Blocked Connector)

Hybrid Headset (Boom Mic Connector)

(2)

(6) (3)

(4)

(5)

Rotary Knob Off/ On/ Volume Level

Primary PTT

Secondary PTT

PTT3 / Hot Key

(+)

(-)

Mode

C4OPS CONTROLS

EAR BUD LEAK TEST

INSERTING EAR BUDS

Shell Ear Retainers Keep mic exposed

Attach collar clip. Hang In Ear Headset on your ear.

Squash foam ear plug.

Pull upper ear up and back and push the ear bud firmly into the canal.

Press ear bud until foam ear plug expands.

Tighten nape slider. Position ear retainer.

“Leak Right”

“Leak Left”

Leak = Reinsert ear plugs / replace ear plug size.

OR

No = Pass

“C4OPS 2X Beep”

(1) Turn MBITR on. Enable MBITR side

connector.

(2) Turn C4OPS on.

“Leak Both”VP

VP

(3) MBITR is auto set to external audio and

keypad locked.

(4) Ear plug sealing test will begin.

(5)

Primary Radio Lead

GETTING STARTED

Primary PTT

VP = Voice Prompt = Important

*