Want more Chief's Shop plans? Visitchiefs­shop.com and look through thePlans section.Be sure to "Like" Chief's Shopon facebook by heading over tofacebook.com/ChiefsShop.

More Plans

lumber4 - 1 x 4 x 81 - 1 x 6 x 64 - 2 x 4 x 85 - 2 x 6 x 8(availability will vary)hardware/supplies1 1 /4" pocket hole screws1 1 /2" pocket hole screwspocket hole plugswood gluepaint/stain

toolsmiter sawj ig sawsander/belt sanderdrill/driverKreg Pocket Hole Jigclampssquarecompass/flexible metal ruler

WhatYou'll Need

SSiimmppllee WWooooddwwoorrkkiinngg::ffaarrmmhhoouussee ddiinniinngg ttaabbllee

© Chris Hill/Chief's Shop 2013 Page 1chiefs‐shop.com

NOTELayout

take care!

About These PlansOn this first page you will see above the project complete. On the last page you'll find thefinished outer dimensions. Be sure to read ALL of the project steps before you start.

To the right is a list of the Lumber, Hardware/Supplies, and Tools you will need to completethis project. A measuring tape and pencil are not included because that should be prettystandard and self explanatory.

Below What You'll Need is the Parts list. This also is included on the Cutting Diagram page,which is the next to last page of this plan document. Also on the Cutting Diagram page is anestimate of the cost of the lumber. This estimate doesn't include any other supplies and doesnot factor in sales tax.

Throughout these plans you'll find the icons below:

This indicates a diagram detailing the dimensions of a project partand/or the placement for pocket holes, screws, nails, etc.

Notes are the instructions for aparticular step/section of the project.

This indicates when to payclose attention to the diagrams,take precautions for safety, etc.

Check out Chief's Shop Videos on YouTube. (cl ick here)

PartsLegs (4) - 1 1 /2 x 3 1 /2 x 28 1 /2End Rails (2) - 3/4 x 3 1 /2 x 30Side Rails (2) - 3/4 x 3 1 /2 x 80Brackets (4) - 3/4 x 5 1 /2 x 15 3/16Stiles (3) - 3/4 x 3 1 /2 x 30Narrow Slats (2) - 1 1 /2 x 3 1 /2 x 92Wide Slats (5) - 1 1 /2 x 5 1 /2 x 92spacer (2) - 1 1 /2 x 3 1 /2 x 1 3/8spacer (4) - 3/4 x 3 1 /2 x 3 1 /2All parts are listed in actual dimensions. Refer tothe Cutting Diagram on the last page of this planas a guide for determining the specific boardfrom which to cut the parts.

© Chris Hill/Chief's Shop 2013 Page 2chiefs‐shop.com

Layout

NOTE Use the layout as a guide for measuring, marking, cutting, and drilling pocket holes in the Legs.Make two of the Legs shown in the top layout, and two of the other. Make two Front Legs. Setyour jig and drill bit for 7/8" stock. This is to allow for 1 1 /2" pocket hole screws to be attachedto 1 1 /2" stock later. These screws will penetrate deep enough to form a strong joint.

SSiimmppllee WWooooddwwoorrkkiinngg::ffaarrmmhhoouussee DDiinniinngg ttaabbllee

Layout

NOTE Use the layout as a guide for measuring, marking, cutting, and drilling pocket holes in the EndRails and Stretchers. Set your jig and drill bit for 3/4" stock 7/8" stock where indicated.

Page 3chiefs‐shop.com © Chris Hill/Chief's Shop 2013

SSiimmppllee WWooooddwwoorrkkiinngg::ffaarrmmhhoouussee DDiinniinngg ttaabbllee

NOTEPosition the parts as shown and attach using glue and1 1 /4-inch pocket hole screws. Clamp the parts inplace during assembly. Make two assemblies.

Layout

NOTE Use the layout as a guide for measuring, marking, cutting, and drilling pocket holes in theSide Rails. Set your jig and drill bit for 3/4" stock 7/8" stock where indicated.

Page 4chiefs‐shop.com © Chris Hill/Chief's Shop 2013

NOTEPosition the parts as shown and attach using glue and1 1 /4-inch pocket hole screws. Clamp the parts inplace during assembly.

SSiimmppllee WWooooddwwoorrkkiinngg::ffaarrmmhhoouussee DDiinniinngg ttaabbllee

Layout

NOTE Use the layout as a guide for measuring, marking, cutting, and drilling pocket holes in theBrackets. Set your jig and drill bit for 3/4" stock where indicated.

© Chris Hill/Chief's Shop 2013chiefs‐shop.com Page 5

NOTEPosition the parts as shown and attach using glue and1 1 /4-inch pocket hole screws. Clamp the parts in placeduring assembly.

SSiimmppllee WWooooddwwoorrkkiinngg::ffaarrmmhhoouussee DDiinniinngg ttaabbllee

NOTEPosition the parts as shown and attach using glue and1 1 /4-inch pocket hole screws. Clamp the parts in placeduring assembly.

© Chris Hill/Chief's Shop 2013chiefs‐shop.com Page 6

NOTEAttach the remaining Side Rail and Bracketsto the other side of the assembly, and theStretchers to the second Side Rail. Positionthe parts as shown and attach using glue and1 1 /4-inch pocket hole screws. Clamp theparts in place during assembly.

NOTEPosition the parts as shown and attach using glue and1 1 /2-inch pocket hole screws. Clamp the parts in placeduring assembly. Drive screws through the End Rails,Side Rails, and Legs into the Narrow Slats andWide Slats.

SSiimmppllee WWooooddwwoorrkkiinngg::ffaarrmmhhoouussee DDiinniinngg ttaabbllee

chiefs‐shop.com © Chris Hill/Chief's Shop 2013

cutting DIAGRAM

take care!Follow ALL SAFETYGUIDELINESAND RECOMMENDATIONS provided bythe manufacturers ofyour tools, and anychemicals such as glue and finishes youuse in this project. YOUare responsiblefor your safety, so use common sensewhen working in the shop!

1 x 6 x 6

PartsLegs (4) - 1 1 /2 x 3 1 /2 x 28 1 /2End Rails (2) - 3/4 x 3 1 /2 x 30Side Rails (2) - 3/4 x 3 1 /2 x 80Brackets (4) - 3/4 x 5 1 /2 x 15 3/16Stiles (3) - 3/4 x 3 1 /2 x 30Narrow Slats (2) - 1 1 /2 x 3 1 /2 x 92Wide Slats (5) - 1 1 /2 x 5 1 /2 x 92spacer (2) - 1 1 /2 x 3 1 /2 x 1 3/8spacer (4) - 3/4 x 3 1 /2 x 3 1 /2All parts are listed in actual dimensions. Refer tothe Cutting Diagram on the last page of this planas a guide for determining the specific boardfrom which to cut the parts.

SSiimmppllee WWooooddwwoorrkkiinngg::ffaarrmmhhoouussee DDiinniinngg ttaabbllee

1 x 4 x 8(4)

2 x 4 x 8(4)

2 x 6 x 8(5)

Page 7