INSTALLATION INSTRUCTIONS-PART 99-7874/99-7874T

99-7874/99-7874T

APPLICATIONSHonda Accord 2008-up

(Excluding dual zone automatic climate controls)

KIT FEATURES

• Painted To Match Factory Dash 99-7874=Charcoal, 99-7874T=Taupe

• DIN Radio Provision with Pocket• ISO Mount Radio Provision with Pocket• Double DIN Radio Provision• Stacked ISO Mount Units Provision

• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets• E) Double DIN Trim Plate • F) Pocket

KIT COMPONENTS

1-800-221-0932

© COPYRIGHT 2008-2010 METRA ELECTRONICS CORPORATION

www.metraonline.com

Small Flat Blade Screwdriver • Panel Removal Tool Phillips Screwdriver • Cutting Tool

WIRING AND ANTENNA CONNECTIONS (Sold Separately)Harness:• 70-1729 - Honda harness 2008-up• 70-1730 - Honda amp interface harness 2008-upAntenna Adapter:• 40-HD10 - Honda antenna adapter 2005-up

TOOLS REQUIRED:

B

F

C D EA

Dash DisassemblyHonda Accord 2008-up(Excluding dual zone automatic climate controls) . . . . . . . . . . . . . . . . . .1,2

Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Kit Assembly- DIN Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . 4- ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . 5- Double DIN /Stacked ISO Mount Units Provision . . . . . . . . . . . . . . . . . 6

Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

TABLE OF CONTENTS

99-7874/99-7874T

*Note:

Refer also to the instructions included with the aftermarket radio.

KNOWLEDGE IS POWEREnhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry.Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.

Metra recommends MECPcertified technicians

99-7874/99-7874T DASH DISASSEMBLY

HONDA ACCORD 2008-UP

1

1

Unclip and remove the trim panel atthe left side of the factory radio.(Figure B)

Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.

3

Unclip and remove the trim panelfrom above the glove box at the rightside of the factory radio. (Figure A)

2

Unclip and remove the top of the cen-ter console including the cup holders.(Figure D)

5

Remove (2) Phillips screws at the bot-tom edge of the pocket assembly.(Figure E)

6

Remove the (2) Phillips screws fromthe left and right side of the of thefactory radio. (Figure C)

4

Continue on page 2.

D

B

C

A

E

7 Remove (2) Phillips screws facing upinside of the pocket below the factoryradio. (Figure F)

Unclip and remove the pocket assem-bly. (Figure G)

8

HONDA ACCORD 2008-UP

2

Remove (2) Phillips screws facing upon the bottom of the factory radio.(Figure H)

9

Unclip and remove the hazardswitch/passenger air bag lightassembly. (Retain the hazardswitch/passenger air bag lightassembly for re-use during kit prepa-ration.)

13

Remove (4) Phillips screws securingtrim panel at the bottom edge of thefactory radio assembly and removethe trim panel. (Retain the screwsand trim panel for re-use during kitpreparation.)

14

Remove (9) clips from the back of thefactory radio assembly. (Retain theclips for re-use during kit prepara-tion.)

15

Remove (6) Phillips screws securingthe climate controls to the factoryradio assembly and remove the con-trols from the assembly. (Retain thescrews and climate controls for re-use during kit preparation.)

11

Remove (4) Phillips screws securingthe a/c vents to the factory radioassembly and remove the a/c ventfrom the assembly. (Retain thescrews and a/c vents for re-use dur-ing kit preparation.)

12

Unclip the factory radio assembly.Unplug and remove the radio assem-bly. (Figure I)

10

Continue to kit preparation.

I

G

H

F

99-7874/99-7874T DASH DISASSEMBLY

HONDA ACCORD 2008-UP

PASSENGER AIRBAG

A/C

MAX A/C

REAR

3

1

Secure the climate controls into theradio housing using the factory hard-ware from rear. (Figure C)

Snap the hazard switch/passenger airbag light assembly into the radiohousing from front. (Figure A)

3

Secure the a/c vents into the radiohousing using the factory hardwarefrom rear. (Figure B)

2

Attach the clips to the back of theradio housing. (Figure E)

5

Secure the trim panel onto the radiohousing using the factory hardware.(Figure D)

4

Continue to kit assembly.

D

B

C

E

A

99-7874/99-7874T DASH DISASSEMBLY

4

A

B

C

DIN MOUNT RADIO PROVISION WITH POCKET

Slide the DIN cage into the RadioHousing and secure by bending themetal locking tabs outward. (Figure A)

1

Slide the aftermarket radio into theDIN cage until it snaps into place.(Figure B)

2

Snap the pocket into the radio housing.(Figure C)

3

Continue to final assembly.

*Note: Refer also to the instructions included with the aftermarket radio.

99-7874/99-7874T KIT ASSEMBLY

5

A

B

C

ISO MOUNT RADIO PROVISION WITH POCKET

Mount the ISO Brackets to the radiousing the screws supplied with theradio. (Figure A)

1

Slide the radio into the Radio Housinguntil it snaps into place. (Figure B)

2

Snap the Trim Plate onto the front ofthe Radio Housing. (Figure C)

3

Snap the Pocket into the Radio Housing. (Figure C)

4

Continue to final assembly.

*Note: Refer also to the instructions included with the aftermarket radio.

99-7874/99-7874T KIT ASSEMBLY

6

DOUBLE DIN/STACKED ISO MOUNT UNITS PROVISION

Cut and remove the center bar fromthe Radio Housing. (Figure A)

1

Snap the Double DIN brackets to theinside edge of the Radio Housing.(Figure B)

2

Slide the Double DIN or stacked ISOmount units into the bracket/radiohousing assembly and secure theunit(s) to the assembly using thescrews supplied with the unit(s).(Figure C)

3

Snap the Double DIN trim plate ontothe front of the Housing/Radio assembly. (Figure C)

4

Continue to final assembly.

*Note: Refer also to the instructions included with the aftermarket radio.

A

B

C

99-7874/99-7874T KIT ASSEMBLY

FINAL ASSEMBLY

(A) Strip wire ends back 1/2"

B) Twist ends together

C) Solder

D) Tape

A

B

C

D

Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ-ually tape off the ends of any unused wires to prevent electrical short circuit.)

Re-connect the negative battery terminal and test the unit for proper operation.

Reassemble radio and dash assemblies in reverse order of disassembly.

1

2

3

FINAL WIRING CONNECTIONSMake wiring connections using the EIA color code chart shown below and the instructions included with thehead unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and

individually tape off ends of any unused wires to prevent electrical short circuit.

METRA / EIA WIRING CODE12V Ignition / Acc . . . . . . . . . . Red

12V Batt / Memory. . . . . . . . . Yellow

Ground. . . . . . . . . . . . . . . . . . Black*

Power Antenna. . . . . . . . . . . . Blue

Amp Turn-On . . . . . . . . . . . . . Blue / White

Amp Ground. . . . . . . . . . . . . . Black / White

Illumination . . . . . . . . . . . . . . Orange

Dimmer . . . . . . . . . . . . . . . . . Orange / White

Right Front (+) . . . . . . . . . . . . Gray

Right Front (-). . . . . . . . . . . . . Gray/ Black

Left Front (+) . . . . . . . . . . . . . White

Left Front (-). . . . . . . . . . . . . . White / Black

Right Rear (+) . . . . . . . . . . . . Violet

Right Rear (-) . . . . . . . . . . . . . Violet / Black

Left Rear (+) . . . . . . . . . . . . . Green

Left Rear (-) . . . . . . . . . . . . . . Green / Black

*NOTE: When a Black wire is not present, ground radio to vehicle chassis. All colors may not be present on all leads due to manufacturer’s specifications.

7

99-7874/99-7874T FINAL ASSEMBLY

NOTES

8

99-7874/99-7874T

NOTES

9

99-7874/99-7874T

99-7874/99-7874T INSTRUCTIONS

1-800-221-0932

REV. 07/27/11 © COPYRIGHT 2008-2010 METRA ELECTRONICS CORPORATION INST99-7874

www.metraonline.com