EX100 QIG TOTOLINK 160824totolink.id/wp-content/uploads/2017/10/EX100_QIG_Ver1.0.pdf · Ext Power...

Ext Power Supply Modes Quick Installation Guide Wireless N Range Extender Information in this document is subject to change without prior notice. Copyrights TOTOLINK. All rights reserved. Website: http://www.totolink.net Method One: Easy Setup by WPS Button Press WPS button on the router. Press the RST/WPS button on EX100 for about 1~2s within 2 minutes. Wireless connection is established, the SSID of EX100 will change to the upper router’s SSID. One-click WPS connection makes it easy to extend the coverage of your existing wireless network. You can put EX100 close to the router to do the WPS connection, then place it anywhere within the Wi-Fi range. EX100 could remember the last connected Wi-Fi and auto connect to it when powered on. TIPS: Model No.: EX100 V1.1608 Click Settings. If your router don’t have a WPS button or you failed to connect to upper router by WPS, please setup EX100 by your Smart phone. Choose Wi-Fi. For more information, please go to www.totolink.net iOS Phone Method Two: Setup via Smart Phone 4 Select TOTOLINK Ext (default SSID), no password required. After successfully connecting, the Log in page pops up automatically. Click GO. 5 All available SSIDs are displayed. Please choose the one you want to extend its Wi-Fi signal. 9 10 Try any website to test the Internet. 1 2 3 Power Bank 4 USB Hub 5 Connection Successfully. 9 10 Connection Successfully. Type in the password, click Connect. 11 Try any website to test the Internet. 6 Enter the right Key(password). Here you’re allowed to setup the EX100’s separated SSID and password as you want or keep it the same as upper AP. Click Connect. 7 Upon a successful connection, the device turns back to the Wi-Fi page automatically. Please choose the extender’s new SSID. 8 Type in the password, click Join. Click Settings. Choose Wi-Fi. Android Phone 4 Select TOTOLINK Ext (default SSID), no password required. After successfully connecting, the Log in page pops up automatically. Click GO. 5 All available SSIDs are displayed. Please choose the one you want to extend its Wi-Fi signal. 6 Enter the right Key (password). Here you’re allowed to setup the EX100’s separated SSID and password as you want or keep it the same as upper AP. Click Connect. 7 Wait for a while, the system reminds you to reconnect Wi-Fi. 8 Get back to the Wi-Fi page manually, choose EX100’s new SSID. 320*220MM 折后110*80MM LED Indicators Ext LED Indicator Button RST/WPS Button Description Press the button for more than 5 seconds, the device will restored to factory default settings. Activity Connected to Power supply equipment(PSE) After power-on Press RST/WPS button for 1~2 seconds Successful Wi-Fi connection to upper router Press RST/WPS button for more than 5 seconds Status Lights red Lights orange Two colors (red and orange) exchange flash Lights green Blinks orange quickly Press the button for 1~2 seconds, WPS function enabled. Ext Ext EX100 EX100 Ext Other USB PSE(router with USB interface) PC/Laptop USB Charger

Upload
others
Category

Documents
view
5
download
0

Embed Size (px):

Transcript of EX100 QIG TOTOLINK 160824totolink.id/wp-content/uploads/2017/10/EX100_QIG_Ver1.0.pdf · Ext Power...

Ext

Power Supply Modes

Quick Installation GuideWireless N Range Extender

Method One: Easy Setup by WPS Button

Press WPS button on the router. Press the RST/WPS button on EX100 for about 1~2s within 2 minutes. Wireless connection is established, the SSID of EX100 will change to the upper router’s SSID.

One-click WPS connection makes it easy to extend the coverage of your existing wireless network.

You can put EX100 close to the router to dothe WPS connection, then place it anywhere within the Wi-Fi range. EX100 could remember the last connected Wi-Fi and auto connect to it when powered on.

TIPS:

Model No.: EX100

V1.1608

Click Settings.

If your router don’t have a WPS button or you failed to connect to upper router by WPS, please setup EX100 by your Smart phone.

Choose Wi-Fi.

For more information, please go to www.totolink.net

iOS Phone

Method Two: Setup via Smart Phone

4Select TOTOLINK Ext (default SSID),no password required.

After successfully connecting, the Log in page pops upautomatically. Click GO.

5 All available SSIDsare displayed. Pleasechoose the one you want to extend its Wi-Fi signal.

9 10 Try any website to test the Internet.

3Power Bank

4USB Hub

Connection Successfully. 9 10 Connection Successfully.Type in the password, click Connect. 11 Try any website to test the Internet.

6 Enter the right Key(password). Hereyou’re allowed to setup the EX100’s separated SSID and password asyou want or keep it the same as upper AP. Click Connect.

7 Upon a successful connection, the device turns back to the Wi-Fi page automatically. Please choose the extender’s new SSID.

8 Type in the password,click Join.

Click Settings. Choose Wi-Fi.

Android Phone

4Select TOTOLINK Ext(default SSID), no password required.

After successfully connecting, the Log in page pops up automatically. Click GO.

5 All available SSIDs are displayed. Please choose the one you want to extend its Wi-Fi signal.

6 Enter the right Key (password). Here you’re allowed to setup the EX100’s separated SSID and password as you want or keep it the same as upper AP. Click Connect.

7 Wait for a while, the system reminds you to reconnect Wi-Fi. 8 Get back to the Wi-Fi page

manually, choose EX100’s new SSID.

320*220MM 折后110*80MM

LED Indicators

Ext

LED Indicator

Button

RST/WPS

Button Description

Press the button for more than 5 seconds, the device will restored to factory default settings.

Activity

Connected to Power supply equipment(PSE)