ETSI EN 300 328 BT

Compliance Certification Services Inc. Date of Issue: December 23, 2013 Report No .: C131213R01-RT

Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. The client should not use it to claim product endorsement by A2LA or any government agencies. The test results in the report only apply to the tested sample

Rev.01 of 34

ETSI EN 300 328 v1.7.1

TEST REPORT For

Product Name: WCDMA ANDROID SMART PHONE Brand Name: thl

Model No.: T5 Series Model: N/A

Test Report Number: C131213R01-RTW

Issued for

SHENZHEN HONGJIAYUAN COMMUNICATION TECHNOLOGY CO.,LTD Rm2406, Block A of Electronic & Technology Building, 2070, Shenzhen Middle Road, Shenzhen

518000 P.R. China

Issued by

Compliance Certification Services Inc.

Kun shan Laboratory

No.10 Weiye Rd., Innovation park, Eco&Tec, Development Zone, Kunshan City, Jiangsu, China

TEL: 86-512-57355888

FAX: 86-512-57370818


of 34 Rev.01 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION ................................................................................................ 4 2. TEST RESULT SUMMARY ......................................................................................................... 5 3. EUT DESCRIPTION .................................................................................................................... 6 4. TEST METHODOLOGY .............................................................................................................. 7 5. FACILITIES AND ACCREDITATIONS ........................................................................................ 8 6. EQUIVALENT ISOTROPIC RADIATED POWER ..................................................................... 11 7. FREQUENCY RANGE ............................................................................................................... 14 8. DWELL TIME ............................................................................................................................. 16 9. HOPPING CHANNEL ................................................................................................................ 18 10. HOPPING SEQUENCE ............................................................................................................. 20 11. MEDIUM ACCESS PROTOCOL ............................................................................................... 22 12. TRANSMITTER SPURIOUS EMISSIONS ................................................................................. 23 13. RECEIVER SPURIOUS EMISSIONS ........................................................................................ 29



Revision History

Rev. Issue Date Revisions Effect Page Revised By

00 December 23, 2013 Initial Issue ALL Jeff.Fang



1. TEST RESULT CERTIFICATION Product Name: WCDMA ANDROID SMART PHONE

Brand Name: thl

Model Name: T5

Series Model: N/A

Application Discrepancy:

N/A

Device Category: Production unit

Applicant: Address:

SHENZHEN HONGJIAYUAN COMMUNICATION TECHNOLOGY CO.,LTD Rm2406, Block A of Electronic & Technology Building, 2070, Shenzhen

Middle Road, Shenzhen 518000 P.R. China

Manufacturer: Address:

SHENZHEN HONGJIAYUAN COMMUNICATION TECHNOLOGY CO.,LTD Rm2406, Block A of Electronic & Technology Building, 2070, Shenzhen

Middle Road, Shenzhen 518000 P.R. China

Standard : ETSI EN 300 328 (V1.7.1: 2006)

Date of Test: December 19, 2013

Test Result: Conform

DEVIATION FROM APPLICABLE STANDARD

None

The above equipment was tested by Compliance Certification Services Inc. for compliance with the requirements set forth in ETSI EN 300 328. The results of testing in this report apply only to the product/system, which was tested. Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties.

Approved by: Tested by:

Jeff.Fang RF Manager Compliance Certification Services Inc.

Blent.Wang Test Engineer Compliance Certification Services Inc.



2. TEST RESULT SUMMARY

Test Parameter SubclauseApplicable

(Yes/No) Result

TRANSMITTER PARAMETERS

Equivalent isotropic radiated power 5.7.2.2 YES Pass

Frequency range 5.7.4 YES Pass

Maximum e.i.r.p. spectral density – except for FHSS 5.7.3 NO --

Dwell time – only for FHSS 4.3.4.1 YES Pass

Hopping Channel – only for FHSS 4.3.4.2 YES Pass

Hopping sequence – only for FHSS 4.3.4.3 YES Pass

Transmitter spurious emissions - conducted 5.7.5 NO --

Transmitter spurious emissions - radiated 5.7.5 YES Pass

Transmitter spurious emissions standby - conducted 5.7.5 NO --

Transmitter spurious emissions standby - radiated 5.7.5 NO --

RECEIVER PARAMETERS

Receiver spurious emissions - conducted 5.7.6 NO --

Receiver spurious emissions - radiated 5.7.6 YES Pass



3. EUT DESCRIPTION Product Name: WCDMA ANDROID SMART PHONE

Brand Name: thl

Model Name: T5

Series Model: N/A

Model Discrepancy: N/A

Frequency Range : 2402 MHz -2480 MHz

Modulation Technique: GFSK(1Mbps),π/4-DQPSK(2Mbps),8-DPSK(3Mbps)

Number of Channels: 79 Channels

Antenna Type: PIFA antenna

Antenna Specification: 0 dBi gain (Max)

Transmit Power: -1.20 dBm

Power Adapter Power Rating :

Power supply and ADP（rating）： Model: UT-059E-698 INPUT: AC100-240V 50/60Hz 0.15A OUTPUT: DC 5V 500mA Battery（rating）： Capacitance: 1950mAh 3.8V

Temperature Range: -15°C ~ 55°C

Remark: For more details, please refer to the User’s manual of the EUT.



4. TEST METHODOLOGY 4.1. DESCRIPTION OF TEST MODES

Software used to control the EUT for staying in continuous transmitting and receiving mode is programmed.

The field strength of spurious emission was measured in the following position: EUT stand-up position (Z

axis), lie-down position (X, Y axis). The worst emission was found in stand-up position (Z axis) and the

worst case was recorded.

RF Test Mode(TX) Test Mode(RX)

Bluetooth Mode 1: Channel Low (2402MHz) Mode 1:Channel Low (2402MHz) Mode 2: Channel High (2480MHz) Mode 2: Channel High (2480MHz)

4.2. SETUP OF EQUIPMENT UNDER TEST 4.2.1. DESCRIPTION OF SUPPORT UNITS

The EUT has been tested as an independent unit along with the following necessary accessories or support units, which are adopted to form a representative test configuration.

No. Manufacture Equipment Model No. Serial No.

1 N/A N/A N/A N/A

Notes: 1) All the equipment/cables were placed in the worst-case configuration to maximize the emission

during the test. 2) Grounding was established in accordance with the manufacturer’s requirements and conditions for

the intended use.

4.2.2. CONFIGURATION OF SYSTEM UNDER TEST

See test photographs attached in Appendix I for the actual connections between EUT and support equipment.



5. FACILITIES AND ACCREDITATIONS 5.1. FACILITIES All measurement facilities used to collect the measurement data are located at

No.10Weiye Rd., Innovation park, Eco&Tec, Development Zone, Kunshan City, Jiangsu, China.

The sites are constructed in conformance with the requirements of ANSI C63.4 and CISPR Publication

22. All receiving equipment conforms to CISPR Publication 16-1, “Radio Interference Measuring Apparatus

and Measurement Methods.”

5.2. ACCREDITATIONS Our laboratories are accredited and approved by the following accreditation body according to ISO/IEC 17025.

USA A2LA China CNAS

The measuring facility of laboratories has been authorized or registered by the following approval agencies.

Canada Industry Canada Japan VCCI Taiwan BSMI USA FCC

Copies of granted accreditation certificates are available for downloading from our web site, http://www.ccsrf.com



5.3. LIST OF MEASURING EQUIPMENT Name of

Equipment Manufacturer Model Serial Number Calibration Due Remark

Spectrum

Analyzer Agilent E4446A MY44020154 2014-04-16 Conducted

Signal

Generator Agilent E8257C MY43321570 2014-05-05 Radiation

Pre-Amplifier CCSRF AMP1277 SN:001 2014-11-04 Radiation

Pre-Amplifier Miteq AMF-6F-260400-40-8P 1037496 2014-04-26 Radiation

Bilog Antenna Sunol JB1 A110204-1 2014-05-02 Radiation

Horn-antenna Schwarzbeck BBHA9120D D:267 2014-04-28 Radiation

Horn Antenna Schwarzbeck BBHA9170 BBHA9170171 N.C.R Radiation

Filter MICRO-TRONICS BRM50701 5 N.C.R Radiation

AC Power

Source EXTECH 6605 1570106 N.C.R

Conducted

DC Power

Supply AGILENT E3632A MY50340053 N.C.R

Conducted

Power Sensor Agilent E9327A US40441788 2014-03-14 Conducted

Power Meter Agilent E4416A QB41292714 2014-04-16 Conducted

Bluetooth Tester R&S CBT 100189 N.C.R Conducted

6dB

ATTENUATOR Mini-Circuits NAT-6-2W 15542-1 N.C.R

Conducted

POWER

DIVIDER AISI IOWOPE2068 PE2068

2013-12-24 Conducted

Temp. / Humidity

Chamber TERCHY MHK-120AK X30109 2014-01-24 Conducted

Spectrum

Analyzer RS FSU26 200789 2014-06-30 Radiation

Notes: 1. Each of the above test instruments is calibrated every 12 months and the calibration is traceable to

NML/ROC and NIST/USA.



5.4. MEASUREMENT UNCERTAINTY The following relevant measurement uncertainties have been estimated and determined following the ETSI Technical Report, ETR 028

Parameter Uncertainty

Radio Frequency +/- 4.1198*10-8

Total RF Power,conducted +/- 2.5290dB

RF Power density,conducted +/- 2.5290dB

Spurious emissions, conducted +/- 2.2727dB

All emissions, radiated +/- 5.1987dB

Temperature +/- 0.6238℃

Humidity +/-3.0540 %

DC Power Source +/-0.6104 %

AC Power Source +/-1.2719 %

These uncertainties represent an expanded uncertainty expressed approximately at the 95% confidence level using a coverage factor of k=2.



6. EQUIVALENT ISOTROPIC RADIATED POWER 6.1. LIMITS

EN 300 328 Clause 4.3.1.2

The equivalent isotropic radiated power shall be equal to or less than -10 dBW (100 mW) E.I.R.P. This limit shall apply for any combination of power level and intended antenna assembly.

6.2. TEST INSTRUMENTS

See list of measuring instruments of this Section 5.3.

6.3. TEST PROCEDURES 1. Please refer to ETSI EN 300 328 (V1.7.1) clause 5.3 for the test conditions.

2. Please refer to ETSI EN 300 328 (V1.7.1) clause 5.7.2.2 for the measurement method. 3. TEST SETUP Temperature and Voltage Measurement (under normal and extreme test conditions)

4. Data Sample EIRP = A+G +CL+10log(1/x) (dBm) A = Reading G = Antenna Gain CL = Cable Loss x = Tx on / (Tx on + Tx off) (0 < X ≤ 1)



6.4. TEST RESULTS No non-compliance noted

EUT Mode : BT 1Mbps(GFSK) Temperature: 20℃

Description: Continuous transmit Relative Humidity : 45~48%

Test By: Blent.Wang Test Date: 2013-12-19

0.99

10 * log (1/x) = 0.04 dB0.00 dBi

Cable Loss= 0.50 dB

Temp (25)°C

CHANNEL 3.8V 3.5V 4.35V 3.5V 4.35V

-2.93 -2.85 -2.86 -3.01 -3.02-2.39 -2.31 -2.32 -2.47 -2.48-2.26 -2.14 -2.15 -2.36 -2.37-1.72 -1.60 -1.61 -1.82 -1.83-1.84 -1.74 -1.75 -2.00 -1.99-1.30 -1.20 -1.21 -1.46 -1.45

20 dBm

Temp (-15)°C Temp (55)°C VoltagePower

Measurement uncertainty ± 2.5290 dB

HighMeasured Power

EIRPLimit Average Limit=

Measured PowerEIRP

Measured Power

Duty Cycle measurement X: (Ton/Ton + Toff) =

Antenna Gain:

Low

MidEIRP

TEST CONDITIONSTRANSMITTER POWER (dBm)

Remark: EIRP = A+G+CL+10log(1/x) (dBm)

A = Reading

G = Antenna Gain

CL = Cable Loss

x = Tx on / (Tx on + Tx off) (0 < X ≤ 1)



EUT Mode : BT 3Mbps (8-DPSK) Temperature: 20℃



0.99

10 * log (1/x) = 0.04 dB0.00 dBi

Cable Loss= 0.50 dB

Temp (25)°C

CHANNEL 3.8V 3.5V 4.35V 3.5V 4.35V

-3.52 -3.33 -3.34 -3.71 -0.37-2.98 -2.79 -2.80 -3.17 0.17-2.87 -2.74 -2.73 -3.01 -3.02-2.33 -2.20 -2.19 -2.47 -2.48-2.50 -2.32 -2.31 -2.74 -2.75-1.96 -1.78 -1.77 -2.20 -2.21

20 dBm

Measured PowerEIRP

Measured Power

Duty Cycle measurement X: (Ton/Ton + Toff) =

Antenna Assembly Gain:

Low

MidEIRP

TEST CONDITIONSTRANSMITTER POWER (dBm)

Temp (-15)°C Temp (55)°C VoltagePower

Measurement uncertainty ± 2.5290 dB

HighMeasured Power

EIRPLimit Average Limit=

Remark: EIRP = A+G-AL+CL+10log(1/x) (dBm)

A = Reading

G = Antenna Gain

G-AL= Antenna Assembly Gain

CL = Cable Loss

x = Tx on / (Tx on + Tx off) (0 < X ≤ 1)



7. FREQUENCY RANGE 7.1. LIMITS

ETSI EN 300 328 clause 4.3.3.2

For all equipment the frequency shall lie within the band 2.4GHz to 2.4835GHz (fL>2.4GHz and

fH<2.4835GHz)



7.3. TEST PROCEDURES 1. Please refer to ETSI EN 300 328 (V1.7.1) clause 5.3 for the test conditions.

2. Please refer to ETSI EN 300 328 (V1.7.1) clause 5.7.4 for the measurement method.

7.4. TEST SETUP

Temperature and Voltage Measurement (under normal and extreme test conditions)

7.5. TEST RESULTS No non-compliance noted



EUT Mode : BT 1Mbps (GFSK) Temperature: 20℃



Test Conditions Frequency Range

Low Frequency(MHz) High Frequency(MHz)

25 °C Vnor 3.8V 2401.671 2480.369

-15 °C Vmin 3.5V 2401.738 2480.463

Vmax 4.35V 2401.738 2480.463

55 °C Vmin 3.5V 2401.153 2480.742

Vmax 4.35V 2401.153 2480.742

Measured frequencies (Lowest and Highest)

2401.153 2480.742

Limit FL > 2400MHz FH < 2483.5MHz

Measurement Uncertainty +/- 4.1198*10-8

EUT Mode : BT 3Mbps (8-DPSK) Temperature: 20℃



Test Conditions Frequency Range

Low Frequency(MHz) High Frequency(MHz)

25 °C Vnor 3.8V 2401.691 2480.481

-15 °C Vmin 3.5V 2401.632 2480.339

Vmax 4.35V 2401.632 2480.339

55 °C Vmin 3.5V 2401.484 2480.204

Vmax 4.35V 2401.484 2480.204

Measured frequencies (Lowest and Highest)

2401.484 2480.481

Limit FL > 2400MHz FH < 2483.5MHz

Measurement Uncertainty +/- 4.1198*10-8



8. DWELL TIME 8.1. LIMITS

ETSI EN 300 328 clause 4.3.4.1.2

The maximum dwell time shall be 0.4s.

8.2. TEST INSTRUMENTS See list of measuring instruments of this Section 5.3.

8.3. TEST PROCEDURES 1. Place the EUT on the table and set it in transmitting mode.

2. Remove the antenna from the EUT and then connect a low loss RF cable from the antenna port to the

spectrum analyzer.

3. The EUT should be transmitting at its all data rate as the worst cases.

4. The EUT must have its hopping function enabled. Use the following spectrum analyzer settings: Span

= zero span, centered on a hopping channel; RBW = 1 MHz; VBW≥RBW; Sweep = as necessary to

capture the entire dwell time per hopping channel; Detector function = peak; Trace = max hold.

5. Use the marker-delta function to calculate the dwell time.

6. Repeat above procedures until all frequency measured were completed. 7.TEST SETUP



8.4. TEST RESULTS No non-compliance noted 1M:

EUT Mode : 1Mbps(GFSK) Temperature: 25℃


Test By: Blent.Wang Test Date: 2013-12-19 DH 1 0.392* (1600/2)/79 * 31.6 = 125.44 (ms)

Pulse Time (ms)

Total of Dwell (ms)

Period Time (s)

Limit (ms) Result

0.392 125.44 31.60 400.00 PASS

DH 3 1.654* (1600/4)/79 * 31.6 = 264.64(ms)

Pulse Time (ms)

Total of Dwell (ms)

Period Time (s)

Limit (ms) Result

1.654 264.64 31.60 400.00 PASS

DH 5 2.902 * (1600/6)/79 * 31.6 = 309.55(ms)

Pulse Time (ms)

Total of Dwell (ms)

Period Time (s)

Limit (ms) Result

2.902 309.55 31.60 400.00 PASS

3M: EUT Mode : 3Mbps (8-DPSK) Temperature: 25℃


Test By: Blent.Wang Test Date: 2013-12-19 DH 1 0.387* (1600/2)/79 * 31.6 = 123.84 (ms)

Pulse Time (ms)

Total of Dwell (ms)

Period Time (s)

Limit (ms) Result

0.387 123.84 31.60 400.00 PASS

DH 3 1.649* (1600/4)/79 * 31.6 = 263.84(ms)

Pulse Time (ms)

Total of Dwell (ms)

Period Time (s)

Limit (ms) Result

1.649 263.84 31.60 400.00 PASS

DH 5 2.903* (1600/6)/79 * 31.6 = 309.65(ms)

Pulse Time (ms)

Total of Dwell (ms)

Period Time (s)

Limit (ms) Result

2.903 309.65 31.60 400.00 PASS



9. HOPPING CHANNEL 9.1. LIMITS

ETSI EN 300 328 clause 4.3.4.2.2 Non-adaptive Frequency Hopping systems shall make use of non-overlapping hopping channels

separated by the channel bandwidth as measured at 20 dB below peak power.

The hopping channels defined within a hopping sequence shall be at least 1 MHz apart (channel

separation).




spectrum analyzer.

3. The EUT should be transmitting at its all data rate as the worst cases.

4. Use the following spectrum analyzer settings: Span = wide enough to capture the peaks of two

adjacent channels; RBW ≥1% of the span; VBW ≥ RBW; Sweep = auto; Detector function = peak; Trace

= max hold.

5. Use the marker-delta function to determine the separation between the peaks of the adjacent

channels.

6.TEST SETUP



9.4. TEST RESULTS 1M:




Channel Separation (MHz) Result

1.000 Pass




Channel Separation (MHz) Result

1.000 Pass



10. HOPPING SEQUENCE 10.1. LIMITS

ETSI EN 300 328 clause 4.3.4.3.2 Non-adaptive Frequency Hopping systems shall make use of a hopping sequence(s) that contains at

least 15 hopping channels.

Adaptive Frequency Hopping systems shall make use of a hopping sequence(s) that is capable of

operating over a minimum of 90 % of the band specified in table 1, from which at any given time a

minimum of 20 hopping channels shall be used.

Each hopping channel of the hopping sequence shall be occupied at least once during a period not

exceeding four times the product of the dwell time per hop and the number of channels.




spectrum analyzer.

3. The modulation types of EUT are irrelevant to number of hopping channels deviation.

4. The EUT must have its hopping function enabled. Use the following spectrum analyzer settings: Span

= the frequency band of operation; RBW≥ 1% of the span; VBW≥ RBW; Sweep = auto; Detector function

= peak; Trace = max hold.

5.The number of hopping frequency used is defined as the device has the numbers of total channel.

6.TEST SETUP



10.4. TEST RESULTS 1M:




Result (No. of CH) Result

79 PASS




Result (No. of CH) Result

79 PASS



11. MEDIUM ACCESS PROTOCOL 11.1. REQUIREMENT

ETSI EN 300 328 clause 4.3.5.2 A medium access protocol is the implemented by the equipment.

11.2. RESULTS

The EUT is accord with medium access protocol.

A medium access protocol is the implemented by the equipment.



12. TRANSMITTER SPURIOUS EMISSIONS 12.1. LIMITS OF RADIATED EMISSIONS MEASUREMENT The spurious emissions of the transmitter shall not exceed the values in tables in the indicated bands:

Transmitter limits for NARROWBAND spurious emissions

Frequency Range Limit when operating Limit when in stand-by

30 MHz to 1 GHz -36 dBm -57 dBm

Above 1 GHz to 12.75 GHz -30 dBm -47 dBm 1.8 GHz to 1.9GHz 5.15 GHz to 5.3GHz -47 dBm -47 dBm

The above limit values apply to narrowband emissions, e.g. as caused by local oscillator leakage. The

measurement bandwidth for such emission may be as small as necessary to achieve a reliable

measurement result.

Wideband emissions shall not exceed the values given as below:

Transmitter limits for WIDEBAND spurious emissions

Frequency Range Limit when operating Limit when in stand-by

30 MHz to 1 GHz -86 dBm -107 dBm

Above 1 GHz to 12.75 GHz -80 dBm -97 dBm 1.8 GHz to 1.9GHz 5.15 GHz to 5.3GHz -97 dBm -97 dBm



12.3. TEST PROCEDURE 1. Please refer to ETSI EN 300 328 (V1.7.1) clause 5.3 for the test conditions. These measurements

shall only be performed at normal test conditions.

2. Please refer to ETSI EN 300 328 (V1.7.1) clause 5.7.5 for the measurement methods.

12.4. TEST SETUP



Below 1GHz

Above 1GHz

Substituted Method Test Set-up

For the in situ test setup, refer to “Photographs of the Test Configuration.



12.5. TEST RESULTS

30MHz to 1GHz

EUT Mode : 1Mbps(GFSK) /TX (CH Low) Temperature: 20℃



Horizontal No. Frequency Reading Correct Result Limit Margin Height Degree Remark

(MHz) (dBm) Factor(dB) (dBm) (dBm) (dB) (cm) (deg.)

1 78.5418 -65.03 19.45 -45.58 -36.00 -9.58 250 138 peak

2 156.2319 -67.29 25.12 -42.17 -36.00 -6.17 250 317 peak

Vertical No. Frequency Reading Correct Result Limit Margin Height Degree Remark


1 83.4192 -85.36 22.59 -62.77 -36.00 -26.77 250 332 peak

2 156.8827 -89.74 24.45 -65.29 -36.00 -29.29 250 187 peak EUT Mode : 1Mbps(GFSK) /TX (CH High) Temperature: 20℃



Horizontal

No. Frequency Reading Correct Result Limit Margin Height Degree Remark


1 89.1746 -62.59 19.70 -42.89 -36.00 -6.89 250 329 peak

2 676.1464 -75.96 31.39 -44.57 -36.00 -8.57 250 233 peak



1 130.5782 -90.36 24.14 -66.22 -36.00 -30.22 250 127 peak

2 315.3871 -92.57 25.70 -66.87 -36.00 -30.87 250 19 peak Remark: 1. The emission behaviour belongs to narrowband spurious emission. 2. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ”

remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor.



EUT Mode : 3Mbps (8-DPSK)/TX (CH Low) Temperature: 20℃





1 748.1786 -75.85 32.53 -43.32 -36.00 -7.32 250 207 peak

2 853.8961 -77.41 33.31 -44.10 -36.00 -8.10 250 321 peak



1 746.6676 -75.96 32.71 -43.25 -36.00 -7.25 250 112 peak

2 906.7595 -77.26 34.11 -43.15 -36.00 -7.15 250 147 peak EUT Mode : 3Mbps (8-DPSK)/TX (CH High) Temperature: 20℃



Horizontal



1 807.2634 -77.56 33.14 -44.42 -36.00 -8.42 250 97 peak

2 889.6212 -78.53 33.60 -44.93 -36.00 -8.93 250 44 peak



1 754.3742 -78.26 32.82 -45.44 -36.00 -9.44 250 305 peak

2 844.1233 -77.03 33.36 -43.67 -36.00 -7.67 250 157 peak Remark: 1 .The emission behaviour belongs to narrowband spurious emission. 2. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ”




1GHz to 12.75GHz

EUT Mode : 1Mbps(GFSK) /TX (CH Low) Temperature: 20℃





1 5000.000 -54.93 6.09 -48.84 -30.00 -18.84 250 92 peak

2 7435.897 -55.94 11.81 -44.13 -30.00 -14.13 250 189 peak



1 4839.744 -55.62 5.41 -50.21 -30.00 -20.21 250 283 peak

2 7352.564 -55.97 11.31 -44.66 -30.00 -14.66 250 95 peak EUT Mode : 1Mbps(GFSK) /TX (CH High) Temperature: 20℃



Horizontal



1 5064.103 -55.32 7.01 -48.31 -30.00 -18.31 250 310 peak

2 7410.256 -55.82 11.52 -44.30 -30.00 -14.30 250 158 peak



1 5108.974 -55.07 7.20 -47.87 -30.00 -17.87 250 249 peak

2 7243.590 -55.14 10.18 -44.96 -30.00 -14.96 250 3 peak Remark: 1. The emission behaviour belongs to narrowband spurious emission. 2. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ”




EUT Mode : 3Mbps (8-DPSK)/TX (CH Low) Temperature: 20℃





1 4801.874 -58.63 5.22 -53.41 -30.00 -23.41 250 115 peak

2 7211.521 -55.74 10.22 -45.52 -30.00 -15.52 250 287 peak



1 4801.321 -59.32 4.77 -54.55 -30.00 -24.55 250 91 peak

2 7211.418 -56.27 10.18 -46.09 -30.00 -16.09 250 19 peak EUT Mode : 3Mbps (8-DPSK)/TX (CH High) Temperature: 20℃



Horizontal



1 4962.268 -58.46 5.61 -52.85 -30.00 -22.85 250 259 peak

2 7441.989 -55.63 11.88 -43.75 -30.00 -13.75 250 148 peak



1 4852.329 -62.36 5.55 -56.81 -30.00 -26.81 250 266 peak

2 7442.417 -55.85 11.73 -44.12 -30.00 -14.12 250 121 peak Remark: 1 .The emission behaviour belongs to narrowband spurious emission. 2. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor.



13. RECEIVER SPURIOUS EMISSIONS 13.1. LIMITS OF RADIATED EMISSIONS MEASUREMENT The spurious emissions of the receiver shall not exceed the values in tables in the indicated bands:

Receiver limits for NARROWBAND spurious emissions

Frequency Range Limit when in stand-by

30 MHz to 1 GHz -57 dBm

Above 1 GHz to 12.75 GHz -47 dBm

The above limit values apply to narrowband emissions, e.g. as caused by local oscillator leakage. The measurement bandwidth for such emission may be as small as necessary to achieve a reliable measurement result.

Wideband emissions shall not exceed the values given as below: Receiver limits for WIDEBAND spurious emissions

Frequency Range Limit when in stand-by

30 MHz to 1 GHz -107 dBm

Above 1 GHz to 12.75 GHz -97 dBm



13.3. TEST PROCEDURE 1. Please refer to ETSI EN 300 328 (V1.7.1) clause 5.3 for the test conditions. These measurements

shall only be performed at normal test conditions. 2. Please refer to ETSI EN 300 328 (V1.7.1) clause 5.7.6 for the measurement methods.

13.4. TEST SETUP



Below 1GHz

Above 1GHz

Substituted Method Test Set-up

For the in situ test setup, refer to “Photographs of the Test Configuration.”



13.5. TEST RESULT 30MHz to 1GHz

EUT Mode : 1Mbps(GFSK) /RX (CH Low) Temperature: 20℃

Description: Continuous Receive Relative Humidity : 45~48%




1 947.7895 -72.69 -0.66 -73.35 -57.00 -16.35 250 103 peak

2 993.2169 -74.85 0.05 -74.80 -57.00 -17.80 250 14 peak



1 797.3649 -73.69 -1.81 -75.50 -57.00 -18.50 250 15 peak

2 936.5497 -70.26 -0.49 -70.75 -57.00 -13.75 250 279 peak EUT Mode : 1Mbps(GFSK) /RX (CH High) Temperature: 20℃



Horizontal



1 872.3687 -75.63 -1.07 -76.70 -57.00 -19.70 250 155 peak

2 947.7498 -72.41 -0.66 -73.07 -57.00 -16.07 250 313 peak



1 749.1549 -75.26 -2.04 -77.30 -57.00 -20.30 250 278 peak

2 952.0364 -70.69 -0.59 -71.28 -57.00 -14.28 250 321 peak Remark: 1. The emission behaviour belongs to narrowband spurious emission. 2. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor.



EUT Mode : 3Mbps (8-DPSK)/RX (CH Low) Temperature: 20℃





1 271.3677 -69.85 -10.06 -79.91 -57.00 -22.91 250 75 peak

2 931.2397 -70.63 -0.31 -70.94 -57.00 -13.94 250 60 peak



1 749.1597 -75.69 -2.04 -77.73 -57.00 -20.73 250 172 peak

2 936.1697 -70.14 -0.49 -70.63 -57.00 -13.63 250 93 peak EUT Mode : 3Mbps (8-DPSK)/RX (CH High) Temperature: 20℃



Horizontal



1 802.5846 -73.63 -1.73 -75.36 -57.00 -18.36 250 263 peak

2 947.2169 -70.58 -0.66 -71.24 -57.00 -14.24 250 275 peak



1 866.9841 -75.63 -1.07 -76.70 -57.00 -19.70 250 315 peak

2 947.3674 -72.06 -0.58 -72.64 -57.00 -15.64 250 312 peak Remark: 1 .The emission behaviour belongs to narrowband spurious emission. 2. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor.



1GHz to 12.75GHz EUT Mode : 1Mbps(GFSK) /RX (CH Low) Temperature: 20℃





1 2240.385 -60.06 2.43 -57.63 -47.00 -10.63 250 51 peak

2 3899.039 -61.23 7.02 -54.21 -47.00 -7.21 250 28 peak



1 2298.077 -59.63 2.93 -56.70 -47.00 -9.70 250 39 peak

2 2855.769 -60.32 3.98 -56.34 -47.00 -9.34 250 105 peak EUT Mode : 1Mbps(GFSK) /RX (CH High) Temperature: 20℃



Horizontal



1 2240.385 -60.61 2.43 -58.18 -47.00 -11.18 250 210 peak

2 3211.539 -61.00 4.93 -56.07 -47.00 -9.07 250 77 peak



1 2360.577 -60.77 2.34 -58.43 -47.00 -11.43 250 12 peak

2 2913.461 -60.48 3.98 -56.50 -47.00 -9.50 250 65 peak Remark: 1. The emission behaviour belongs to narrowband spurious emission. 2. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor.



EUT Mode : 3Mbps (8-DPSK)/RX (CH Low) Temperature: 20℃





1 1370.158 -69.52 -0.38 -69.90 -47.00 -22.90 250 247 peak

2 3822.789 -66.17 7.08 -59.09 -47.00 -12.09 250 264 peak



1 1250.894 -69.23 0.21 -69.02 -47.00 -22.02 250 134 peak

2 3812.125 -67.49 7.19 -60.30 -47.00 -13.30 250 274 peak EUT Mode : 3Mbps (8-DPSK)/RX (CH High) Temperature: 20℃



Horizontal



1 1514.793 -68.41 -0.54 -68.95 -47.00 -21.95 250 359 peak

2 3250.814 -67.41 5.32 -62.09 -47.00 -15.09 250 260 peak



1 1302.745 -70.42 0.13 -70.29 -47.00 -23.29 250 241 peak

2 3605.752 -66.96 5.61 -61.35 -47.00 -14.35 250 209 peak Remark: 1. The emission behaviour belongs to narrowband spurious emission. 2. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor.

END OF REPORT

ETSI EN 300 328 BT

Documents

Transcript of ETSI EN 300 328 BT