ETABS Exmple1
-
Upload
anonymous-nwbyj9l -
Category
Documents
-
view
321 -
download
9
Transcript of ETABS Exmple1
-
7/29/2019 ETABS Exmple1
1/33
LEARNING OF ETABS SOFTWAREPROBLEM
Beam sizes 300450 mmColumns sizes 300450 mmSlab thickness 120 mmStorey Height 3.2 m.Live Load 3 kN/mFloor Finish Load 1 kN/m2
Concrete grade M25Steel Fe415Earthquake parameters considered are:Zone VResponse Reduction Factor :5
Importance Factor :1Soil : Medium
-
7/29/2019 ETABS Exmple1
2/33
STEP BY STEP PROCEURE:STEP 1: (Creation of geometry)Open the ETABS Program.
Set the units of the model in the drop down box in the lower right handcorner of ETABS window , click the drop down box to set units in KN.m.
-
7/29/2019 ETABS Exmple1
3/33
From Main menu File New Model Select No.
Building Pan Grid System and Storey Data Definition will be displayed.
Uniform Grid SpacingNo. of lines in X Direction = 5No. of lines in Y Direction = 4Spacing in X Direction = 5mSpacing in y Direction = 4m
Simple Grid DataNo. of stories =5
Typical Storey Height = 3.2mBottom storey height = 3.2m
Select Grid only button OK.
-
7/29/2019 ETABS Exmple1
4/33
Note: You can change Grid spacing by choosing Custom Grid spacing,for column varying spacing then click Edit Grid you can also changeany storey height by choosing Custom Storey Data, then click on EditStorey Data.
-
7/29/2019 ETABS Exmple1
5/33
Go to Main menu Edit Storey data Edit Storey.
-
7/29/2019 ETABS Exmple1
6/33
STEP 2: (Design Preference code)
From Main menu Options Preferences Concrete Frame design
Design code =Indian IS456-2000.Ok.
-
7/29/2019 ETABS Exmple1
7/33
-
7/29/2019 ETABS Exmple1
8/33
-
7/29/2019 ETABS Exmple1
9/33
STEP 3: (Define Material Properties)
From Main menu Define Material Property Add new material Material Name =M25Concrete cubic comp. strength fck =25
Bending Reinforcement yield strength fy =415Shear Reinforcement yield strength fy =415 Ok Ok.
STEP 4: (Define Frame section)Define Beam:
From Main menu Define Frame section Add rectangular
Material name =M25 (select) Section Name=B300x450.
-
7/29/2019 ETABS Exmple1
10/33
-
7/29/2019 ETABS Exmple1
11/33
Dimensions:Depth (3) =0.45mWidth (2) =0.30m
Click reinforcement
Select Beam Concrete cover to rebar center Top = 0.04m(=25+8+16/2=41 mm)
Bottom =0.04m Ok Ok.
-
7/29/2019 ETABS Exmple1
12/33
Define Column:
Add Rectangular section Name =C300x450.Material name = M25Dimensions :Depth (3) =0.3m
Width (2) =0.45m
Click reinforcement
Select Column
Select Rectangular
Ties RectangularCover to rebar centre= 0.056 (40+8+16/2=56mm)Bar size =16 dCorner bar =16 d
Reinforcement to be designed Ok Ok.
Define Slab:
From Main menu define Wall/Slab /Deck section Add New slab
Section name = S1
Material name = M25. MembraneMembrane =0.120 m
Bending =0.125m
Select Membrane Ok Ok.
-
7/29/2019 ETABS Exmple1
13/33
STEP 6: (Drawing Beams, Columns and Slabs)Drawing Beams:
From Main menu Draw Draw line objects Create lines in regionsor at clicks(plan,Elev.,3D)Property = -Select required beam size B300x450Click or Select the beam B300x450 in Plan view (Left window) (withsimilar storey option) and select all beam B300x450.
Close.
-
7/29/2019 ETABS Exmple1
14/33
Drawing Columns:
From Main menu Draw Draw line objects Create column in
region or clicks(plan)
Property = C300x450 Select or Click on the column joints in Plan view (Left window) with
similar storey option. If necessary change angle =90 Close.
Drawing Slab:
-
7/29/2019 ETABS Exmple1
15/33
From Main menu Draw Draw area objects Create areas at click
or click (Plan, Elev.) (Plan) Property =S120 Click on theperiphery of column joints and press enter (With similar storey option).
Note:
To view the assigned Beam in plan
Select Set Building Objects on top of Tool bar.
Select Line sections under object view options.
To view the assigned Column in plan
Select Set Building Objects on top of Tool bar.
Select section under view by colour
Select Line labels under object view options
To view the assigned Slab in plan
Select Set Building Objects on top of Tool bar.
Select Area sections under object view options.
To view the rendered view
Set Building view objects on top of Tool bar
Line section.
-
7/29/2019 ETABS Exmple1
16/33
Special Effects:
Object Fill
Extrusion
Apply to all windows Ok.
STEP 7:(Assigning Support Condition)
Set Base floor Plan view in left window
Main menu Select By storey level select Base Ok.Set Column points (with mouse)
From Main menu Assign Joint/Point Restraints (supports)
Select Fixed Ok.
-
7/29/2019 ETABS Exmple1
17/33
To view Support assigned
From top Tool bar Set Building view option
Visible in view Supports Ok.
Go to Elevation view 1 and view . For other views click arrow attop of tool bar.
STEP 8 : (Defining Loads)1.Gravity Loads (Dead Load & Live Load)
From Main menu Define Static Load Cases Load = SDL (Super Imposed Dead Load)Type = Dead
Self weight multiplier =0 Add New Load Ok.
Load = WallType= Dead
Self weight multiplier =0 Add New Load Ok.
-
7/29/2019 ETABS Exmple1
18/33
Note:For Self weight multiplier will be 1 for beams and columns of deadload. For all other loads, it will be zero.
Assigning the Loads:
Activate left window and set to Plan view Activate or select similarstorey option (at bottom) and select all slabs
From Main menu Assign
Shell / Area loads Uniform Load case name =SDL
Uniform loadLoad = 1.50 Kn/m2 (units Kn.m)
Direction Gravity Ok.In the same manner assign Load case name = Live
Uniform loadLoad = 2.0 Kn/m2 (units Kn.m)
Direction Gravity Ok.
-
7/29/2019 ETABS Exmple1
19/33
Assigning Wall loads:9 wall load = 12Kn/m (For external or outer beams)41/2 wall load=6 Kn/m (For internal beams).In left side window select all outer beams in top floor by setting similarstorey options and view the status bar to know no. of beams selected
From Main menu Assign Frame /Line loads Distributed Load case name = wall. Unit Kn.m
ForcesDirection GravityUniform load=12 Kn/m
Replace existing loads Ok.In the same manner apply 41/2 wall udl load to internal beams bysetting all floor options.
To see the load assigned :
Right click the particular member corresponding load Ok.
Note:For point load :
From Main menu Assign Joint/Point loads ForcesLoad case name =Dead. Units Kn.m.Forces Global =10 Kn
Replace existing loads
Ok.
-
7/29/2019 ETABS Exmple1
20/33
To view slab loads:
Display Show Loads Shell/Area view.To see the loads on beam:Right click on any beam, we can see number of information on loadingon beam.
2. Wind Loads :In ETABS there are two ways to define lateral loads (Wind, earthquake). Built in option will automatically calculate lateral loads as peravailable design codes.
Define wind load parameters as per IS 875 --Part 3 (1987)
From Main menu Define Static Load cases Load = Wind X or Wind Y
-
7/29/2019 ETABS Exmple1
21/33
Type = WindSelf weight multiplier =0
Auto Lateral load =IS 8751987 Add New Load Select wind Xload and click on modify lateral loads to specify required wind load
parameter as per IS 875 Ok Ok.
Creating dummy areas with property =None
Set required elevation view in right window From Main menu
Draw Draw area objects Draw rectangular areas Property =
None Click on the perimeter of area and press enter.
Foot Note: Apply wind load for selections.To select wind area
Main menu Select By area object type select null Ok.
Assigning wind loads
Select drawing area of required elevation
From Main menu Assign Shell/area loads Wind Pressurecoefficients
Wind load case name =Wind X
Coefficient Cp= - (Change if required) Ok.
To see wind load selection
Set Building view option
Area section
Line section Ok.
3. Earthquake AnalysisIn building, slab is considered as single rigid member duringearthquake analysis.Select left side window.
Select all slabs by setting all floors/ similar storey option From Main
menu Define Diaphragms Select D1 Modify/ Show
diaphragms Select Rigid Ok Ok.
-
7/29/2019 ETABS Exmple1
22/33
Define Mass SourceAs per IS 1893--2002 25% of Live load is considered on all floors ofbuilding.
From Main menu Define Mass source select From Loads
Load =Dead; Multiplier --1.0 Add
Load = Live; Multiplier =0.25 Add
Load =SDL; Multiplier =1.0 Add
Load = Wall; Multiplier =1.0 Add Ok.
Define Earthquake Load (Static Method)
From Main menu Define Static Load cases Load =EQXType = QuakeDefault Multiplier =0
Auto Lateral load = IS 18932002
Add New Load Select the load EQX Modify lateral load If
required change values as per IS 1893 Select X Direction
-
7/29/2019 ETABS Exmple1
23/33
Select Program calc per code =0.16 (change as per requirement)
Ok Ok.
Assigning Diaphragms
Set all storey option and select all slabs From Main menu Assign
Shell area Diaphragms D1 Ok.Define Earthquake Load (Response Spectrum or Dynamic method)
-
7/29/2019 ETABS Exmple1
24/33
From Main menu Define Response Spectrum Functions IS 1893
-2002 select IS 1893-2002Spectrum Ok. Select IS1893
Modify/Show Spectrum Spectrum case name =IS1893
Damping =0.05 Modal combination CQC Directed Combination SRSS
Function name=1893; Function damping ration=0.05Seismic zone factor z=0.16 ; Soil type =1 Ok.
To view the Diaphragm
Go to Set Building View objects
Diaphragm
STEP 8 : ( Design)
Selecting Indian Code
From Main menu Options Preferences Concrete Frame
Design code = Indian IS 456-2000. Ok.
Defining Load Combination
From Main menu Define Load Combinations Add New Load
Comb Load Combination Name =DL+LL
Load Combination type =Add Change scale factor =1.5 for DL and
LL by clicking add button Add New Load Comb Load Combination Name =DL+WL
Load Combination type =Add Change scale factor =1.5 for DL and
WL by clicking add button Add New Load Comb Load Combination Name =DL+EQX
Load Combination type =Add Change scale factor =1.5 for DL and
EQX by clicking add button Ok Ok.
Selecting Design Load ( i.e. DL+LL)
From Main menu Design Concrete Frame design Select design
comb Select our combination load from the list Add Ok.
-
7/29/2019 ETABS Exmple1
25/33
STEP 9 : (Analysis)
From Main menu Analysis Run analysis.
-
7/29/2019 ETABS Exmple1
26/33
After completing process, the model automatically displaces deformedshape view and the model is locked (you cannot do any changes ).
STEP 10 : (Running the Design Process)
From Main menu Design Concrete frame design Start Design/
Check of Structure Design results will be displayed on the model.
Graphical output:
Activate 3D view in right window by clicking title bar Set elevationview =1 From Main menu Display Show member force/Stresses
diagrams Frame/Pier/Spandrel forces Select any load case say DL+LL.Select moment 3 option
Uncheck the fill diagram.
If it is checked, we have to deselect. check the showed values on
the diagram check box Ok.Right click on any beam in right window which will display diagrams forthe beams.
-
7/29/2019 ETABS Exmple1
27/33
Select scroll for values (Right top window which will show at differentdistances along the beam.
-
7/29/2019 ETABS Exmple1
28/33
To clear the display:
Activate right window From Main menu Display Show un
deformed shape Click on 3D button from top tool bar to display 3D
view.To view reinforcement detail:
Running the Design Process
From Main menu Design Concrete Frame Design start design
/Check of Structure Design results will be displayed in the model.
Set to Elevation view=1 in right window Reinforcement area will bedisplayed on the frame. Right click on any beam or column. We can
select various options:- Summary
- Flexural details
- Shear details etc.
- Envelope Ok.
-
7/29/2019 ETABS Exmple1
29/33
View the % of steel on beams and columns
-
7/29/2019 ETABS Exmple1
30/33
From Main menu Design Concrete Frame Design Display design
information select Design output=rebar percentage Ok.
-
7/29/2019 ETABS Exmple1
31/33
-
7/29/2019 ETABS Exmple1
32/33
-
7/29/2019 ETABS Exmple1
33/33