Esquema Do Pedal Rebote Delay 2.5
1
+ 9v AC ADAPTOR INPUT Vin Gnd Vout +5vDC OUTPUT Schematic +9v 2399 2399 3 5 2 6 1 4 7 8 IC2a IC2b Vb Vb Vb 16 13 Delay Out 15 14 Delay In 100k-B 25k-B REP. 1 2 3 4 5 6 7 8 9 10 11 12 +5vDC 50k-B NC Delay Out DLY. LEVEL Layout and presentation by Francisco Peña 2001-2005®. All rights reserved. Authorization for personal use only, any commercial use is forbidden. Permission for posting/serving limited to Permission refused for posting from other sites. http://www.tonepad.com 100k 240k 33k 47k 15k 24k 24k 24k 510k 510k 1k 12k 12k 12k 12k 12k 12k 12k 12k 2k7 1k 1M 51pF 560pF .001 .027 .01 .1uF .01 .01 .01 47uF 1uF 47uF 1uF 1uF 1uF 47uF 47uF 47uF .1 .082 .082 .1 .1 .082 5pF +9v LAYOUT FP 2005 FP 2005 REBOTE2.5 REBOTE2.5 TONEPAD.COM TONEPAD.COM 0 ½ 1 1½ 2 0 ½ 1 1½ 2 READY TO TRANSFER Rebote Delay 2.5 Rev.3.May.31.2006 Resistors 2 - 1k 1 - 2k7 (2.7k) 8 - 12k 1 - 15k* 3 - 24k 1 - 33k 1 - 47k 1 - 100k 1 - 240k 2 - 510k 1 - 1M Capacitors 5 - 47 μF 4 - 1 μF 4 - 0.1μF 3 - 0.082 μF 4 - 0.01 μF 1 - 0.027 μF 1 - 560pF 1 - 0.001 μF 1 - 51pF 1 - 5pF Parts List NOTES: 5 volt regulator IC3 must be oriented so that its pins match the layout. (in case of using 1,000mA regulator) * Can be changed from 15k to 10k to get endless repeats with repeats pot maxed. If this results in undesired runaway repeats, change it to 11k, or a 6.8k resistor in series with a 5k trimpot adjusted for endless repeats. Pots 1 - 25k lin. 1 - 50k lin. 1 - 100k lin. IC’s IC1 - PT2399 IC2 - TL072 IC3 - 5v positive Regulator (78L05) 1 1 1 3 3 3 2 2 2 510k 510k .082 .082 IN IN 12k 12k 1M 1M 1k 1k 12k 12k 240k 240k IC 2 IC 2 24k 24k .01 .01 51pF 51pF 24k 24k 33k 33k 100k 100k OUT OUT + 1uF 1uF + 1uF 1uF 12 11 10 9 14 15 16 13 3 4 5 6 1 2 7 8 PT2399 PT2399 +9v +9v REPEATS REPEATS DELAY DELAY + 1uF 1uF + 1uF 1uF 47k 47k 2k7 2k7 12k 12k 15k 15k 24k 24k 12k 12k 12k 12k 560pF 560pF .001 .001 .082 .082 5pF 5pF .082 .082 0.1 0.1 0.1 0.1 0.1 0.1 .01 .01 .01 .01 + 47uF 47uF + 47uF 47uF + 47uF 47uF + 47uF 47uF + 47uF 47uF L E V E L L E V E L GND GND 1k 1k IC3 IC3 12k 12k .027 .027 12k 12k .01 .01 12k 12k 0.1 0.1 510k 510k 50k-B 50k-B 100k-B 100k-B 25k-B 25k-B This is an attempt to improve on the Tonepad Rebote2 Delay by providing better filtering. Shortest delay time is 10mS. Maximum delay time is 580mS, repeats become a little dirty with longest delay times, they are clean on shorter delay times. Off board components except for the potentiometers are not shown on the layout. Trademarks are property of their owners. Visit for more! tonepad.com
-
Upload
diogo-campos-castro -
Category
Documents
-
view
260 -
download
43
Transcript of Esquema Do Pedal Rebote Delay 2.5
+
9v
ACADAPTOR
INPUT
Vin
Gnd
Vout +5vDC
OUTPUT
Schematic+9v
2399 2399
3
52
6
1
4
78
IC2a
IC2b
Vb
Vb
Vb
16 13Delay Out
15 14
Delay In
10
0k
-B
25
k-B
REP.
1
2
3
4
5
6
7
8 9
10
11
12
+5vDC
50
k-B
NC
De
lay
Ou
t
DLY.
LEVEL
La
you
t a
nd
pre
sen
tatio
n b
y F
ran
cisc
o P
eñ
a 2
00
1-2
00
5®
.A
ll rig
hts
re
serv
ed
. A
uth
oriza
tion
fo
r p
ers
on
al u
se o
nly
,a
ny
com
me
rcia
l use
is fo
rbid
de
n.
Pe
rmis
sio
n fo
r p
ost
ing
/se
rvin
g li
mite
d to
Pe
rmis
sio
n r
efu
sed
fo
r p
ost
ing
fro
m o
the
r si
tes.
http
://w
ww
.to
ne
pa
d.c
om
100k
240k
33k
47k
15k
24k
24k
24k510k
510k
1k
12k
12k
12k 12k12k12k 12k 12k 2k7
1k
1M
51pF
560pF .001
.027 .01
.1uF
.01 .01 .01
47uF
1uF
47uF
1uF
1uF1uF
47uF47uF47uF
.1
.082
.082
.1
.1
.082
5pF
+9v
LAYOUT
FP 2005
FP 2005
REBOTE2.5
REBOTE2.5
TONEPAD.COM
TONEPAD.COM
0 ½ 1 1½ 2
0
½
1
1½
2
READY TO TRANSFER
Rebote Delay 2.5Rev.3.May.31.2006
Resistors2 - 1k1 - 2k7 (2.7k)8 - 12k1 - 15k*3 - 24k1 - 33k1 - 47k1 - 100k1 - 240k2 - 510k1 - 1M
Capacitors5 - 47 µF4 - 1 µF4 - 0.1µF3 - 0.082 µF4 - 0.01 µF1 - 0.027 µF1 - 560pF1 - 0.001 µF1 - 51pF1 - 5pF
Parts ListNOTES:5 volt regulator IC3 must be oriented so that its pins match the layout. (in case of using 1,000mA regulator)
* Can be changed from 15k to 10k to get endless repeats with repeats pot maxed. If this results in undesired runaway repeats, change it to 11k, or a 6.8k resistor in series with a 5k trimpot adjusted for endless repeats.
Pots1 - 25k lin.1 - 50k lin.1 - 100k lin.
IC’sIC1 - PT2399IC2 - TL072
IC3 - 5v positive Regulator(78L05)
11
1
33
3
22
2
510k510k.082.082
ININ
12k
12k1M1M
1k1k
12k
12k
240k240k
IC 2IC 2
24k
24k
.01.01
51pF51pF24k
24k
33k33k
100k100kOUTOUT
++1uF1uF++
1uF1uF
12
11
10
914
15
16
13
34
56
12
78
PT2399
PT2399
+9v+9v REPEATSREPEATSDELAYDELAY
++1uF1uF
++
1uF1uF
47k47k
2k7
2k7
12k
12k
15k
15k
24k24k
12k12k12k12k
560pF560pF
.001.001
.082.082
5pF
5pF
.082.0820.10.1
0.10.1
0.10.1
.01
.01
.01.01
++
47uF47uF
++
47uF47uF
++
47uF47uF
++
47uF 47uF
++
47uF47uF
L E V E LL E V E LGNDGND
1k1k
IC3IC3
12k12k
.027
.027
12k12k
.01
.01
12k12k
0.1
0.1
510
k510
k
50k-B50k-B 100k-B100k-B 25k-B25k-B
This is an attempt to improve on the Tonepad Rebote2 Delay by providing better filtering. Shortest delay time is 10mS. Maximum delay time is 580mS, repeats become a little dirty with longest delay times, they are clean on shorter delay times. Off board components except for the potentiometers are not shown on the layout. Trademarks are property of their owners. Visit for more!tonepad.com
