ESDS LCD Navigation Map v2.1
-
Upload
yaheba1929 -
Category
Documents
-
view
139 -
download
1
Transcript of ESDS LCD Navigation Map v2.1
- 1 -
EonStor DS Series LCD Navigation MapFor FW 3.85 or Later
Ver 2.1 February 2011
DS S12F-G1433 Ready
View and Edit Logical Drives
HOLD
View and Edit Drives
View and Edit Logical Volume
View and Edit Host LUNs
View and Edit Channels
View and Edit Peripheral Dev
System Functions
View System Information
View and Edit Event Logs
View and Edit Config Parms
Navigating the LCD Menu
ESC
Steps back to the previous menu. (Moves left)
ENT
Proceeds to the next step. (Moves right)HOLD
Long press the ENT key.
Selects the menus or parameters.
• Long-press (HOLD) the ENT key to enter the menu.
• Use to scroll.
• Use ESC to step back.
• See the next page for other conventions.
Press 2 Seconds for Main Menu
ENT
Entering the main menu
Switching the Controller
DS S12F-G1433 P Ready
1. At the top right corner, the “P” sign shows Primary controller.
2. Press and hold the Up and Down keys together for one second.
3. The sign changes to “S,” showing Secondary controller.
- 2 -
Conventions and Notes
Initializing... Please Wait
Power on Self Test, Please Wait
Power on Self Test Completed
DS S12F-G1433 1GB RAM, Wait...
DS S12F-G1433 Ready
Parameters
Critical messageto scroll
2010/11/22 16:03 Critical Generalized Target Event Peripheral Set 0 Device ALERT PSU1 Failure Detected
ENT
DS S12F-G1433 Ready
Term Emul EnableParameters and context-sensitive menu items are marked in italic.
(S12F-G1433 is a model name.) (Enable is a parameter.)
Optional menu Dotted line indicate optional menus that will appear only under certain conditions.
Press 2 seconds Skip View Events
HOLD Clear
Power-up sequence
LG=0 R5 DRV=4 25500MB GD SB=0
LG=1 Not Defined?
Existing logical drives Undefined logical drives
Password input If you have set the password, changing settings might require entering the password. ConfirmHOLD
Enable Adaptive Write Policy ?
Enabled Disabled
HOLDInput Password _
to select, ENT to enter
0 1 2 3 4 5 6 7 8 9 . ! “ # $ % & ‘ ( ) * + , - / : ; < = > ? @ [ ] ^ _ ‘ { | } a b c d e f g h i j k l m n o p q r s t u v w x y z A B C D E F G H I J K L M N O P Q R S T U V X Y Z
( Full Character list )
Character entry Some menu items require you to enter numbers or characters. Scroll down to select the character and press ENT to select. HOLD the ENT key to finish the entry.
* Available characters vary.
Change Enter LD: _
to select, ENT to enter
Shown to the right is the sequence of menus that appear on power-up or system reset.
When a critical event occurs, a notice will appear onscreen. Scroll down the list to read the whole message and HOLD the ENT key to clear the message.
- 3 -
Logical Drive 1/3 – Existing Logical Drives
View and Edit Logical Drives
LG=0 R5 DRV=4 25500MB GD SB=0
ENT ENTView Drives
ENTSlot=4 238214MB LG0 LN HDT722525
Delete Logical Drive
Logical Drive Name
Existing logical drives
LDs that are not part of an LV
ENTChange LD Name: Name ?
HOLDChange Enter LD: _
to select, ENT to enter
Migrate Logical Drive
LDs that are not part of an LV
Expand Logical Drive
ENTExpandable Size 229714MB
ENTMaxsiz=229714MB SetTo 229714MB?
to select, ENT to enter
HOLD Confirm
HOLD Confirm
Initialization Mode Online
ENTInitialization Mode to Offline?
HOLD Confirm
Online Offline
Execute Expand Logical Drive
ENTExecute Expand logical Drive?
HOLD Confirm
Add DrivesWhen drives are available
to select
ENTDelete LG ID=1DB25FA6 ?
HOLD Confirm
ENTMigrate Logical Drive ?
Initialize Progress
ENTInit Online 12%
Initialization, addition, migration
ENTAdd Drv Selected To select drives
ENT
HOLDAdding 12% □_______________
Slot=1 238214MB FRMT DRV HDT7225
ENTSlot=1 238214MB *LG=0 SL_JDT7225
Slot=* 238214MB FRMT DRV HDT7225
ENTSlot=* 238214MB *LG=0 SL_JDT7225
… Last member
to select First member
RAID Level > 3
After initialization
HOLDMigrating 12% □_______________
Logical Drive Assignment
ENTAssign LG To Slot B ?
Slot A Slot B
HOLD Confirm
Regenerate Parity
LG=1 Not Defined?
Undefined logical drives
- 4 -
Logical Drive 2/3 – Existing Logical Drives (Continued)
Regenerate Parity
ENTOverwrite When Inconsistency
ENT
Events On When Inconsistency
Overwrite ----------------- Enable Disable
HOLD Confirm
to select
ENTEvents ----------------- Enable Disable
HOLD Confirm
to select
Execute Parity Check
ENTExecute Parity Check ?
HOLDReparity 30% □□□□__________
Copy and Replace Drive
ENTEnter to Select a On-line Drive
ENTSlot=1 238212MB LG0 LN HDT722525
to select
Progress
Write PolicyENT
Write PolicyTo ----------------- Default Write-Back Write-Through
HOLD Confirm
Shutdown Logical Drive
HOLD ConfirmENTShutdown LG ID=2609795E ?
Restart LDHOLD ConfirmENT
Restart LD?After shutdown
After initialization
ENTEnter to Select One New Drive
ENTSlot=1 238212MB LG0 LN HDT722525
to select
ENTCopy and Replace Drive ?
HOLD
Copy&Replace 30% □□□□__________
ProgressMedia Scan
ENTPriority Normal
ENT HOLD Confirm
Iteration Count Single Time
ENTIteration Count ----------------- Single Time Continuous
HOLD Confirm
to select
to select
Execute Media Scan
ENTExec Media Scan
?HOLD Confirm
Priority Normal ? ----------------- Low Normal Improved High
Undelete/Restore LD List
ENTLG R1 DRV=0 931GB DELETED
to select
ENTView Drives
ENTSlot=5 953609MB LG2 LN Hitachi H
to select
Undelete Logical Drive
ENTUndelete LG ID=22017771 ?
Deleted LD Available
to select
Not applicable to RAID 0 and NRAID
HOLD Confirm
- 5 -
Logical Drive 3/3 – Undefined Logical Drives
LG=1 Not Defined?
HOLDCreate New Logical Drive
ENT
Undelete/Restore LD List
to selectUndefined logical drives
LG=0 R5 DRV=4 25500MB GD SB=0
TDRV=4 Create LG Level=RAID 6 ? ----------------- 6 5 3 1 0 NRAID
HOLDRAID Selected To Select Drives
ENTLG=0 R5 DEV=0 25500MB DELETED
to select
ENTView Drives
ENTSlot=4 238214MB FRMT DEV HDT7225
to select
Undelete LG ID=1DB25FA6 ?
HOLD Confirm
Slot=1 238214MB FRMT DRV HDT7225
ENTSlot=1 238214MB *LG=0 SL_JDT7225
Slot=* 238214MB FRMT DRV HDT7225
ENTSlot=* 238214MB *LG=0 SL_JDT7225
… Last member
Change Logical Drv Parameter
ENT
When deleted LDs exist
ENTMaximum Drive Capacity
ENTMaxsiz=238214MB SetTo 238214MB ?
HOLD Confirm
Spare Drive Assignments
ENTSlot=3 238214MB FRMT DRV HDT7225
to select
ENTSlot=3 238214MB LG=0 SL_HDT7225
Disk Rev. Space 256MB
Write Policy Default
ENT HOLD ConfirmWrite Policy ----------------- Default Write-Back Write-Through
HOLD
Confirm
HOLDInit Online 12% □_______________
Create Logical Drive?
HOLD
to select First member
Logical Drive Assignments
ENTRedund Ctlr LG Assign to Slot B
Redund Ctlr LG Assign to Slot A
HOLD Confirm
Existing logical drives
- 6 -
Logical Volume 1/2 – Existing Logical Volumes
View and Edit Logical Volume
LV=0 24GB GOOD 5A8C0CC43C1DBIF6
ENT ENTView Logical Drivers
ENTLG0 RAID5 DRV=4 25500MB GD SB=0
Delete Logical Volume
Partition Logical Volume
Existing logical volumes
Unmapped logical volume
Logical Volume Name
ENTName: _
HOLD Confirm
Expand Logical Volume
ENTExpand Size: 12076MB ?
HOLD Confirm
to select, ENT to enter
to select, ENT to enter
Change Write Policy
ENTWrite Policy ----------------- Default Write-Back Write-Through
HOLD Confirm
to select
LV=0 Part=0 10GB
ENTAdd Partition
ENTAdd Partition
?Partition Size- 12076
ENTMaxsiz=12076MB SetTo 12076MB?
HOLD Confirm
Partition name Name
ENTName: _
HOLD Confirm
Expand PartitionENT
Expand Size: 12076MB ?
HOLD Confirm
to select, ENT to enter
to select, ENT to enter
Delete PartitionENT
ENT
ENT
to select
to select
LV=0 Not Defined ?
Undefined logical volumes
ENTDelete Logical Volume ?
Delete In Progress
HOLD
When free space is available
Delete Partition ?
Delete In Progress
HOLD
Unmapped logical volume
When space is available
Expand Logical Volume
ENTExpand Size: 12076MB ?
HOLD Confirm
to select, ENT to enter Existing partitions
Existing partitions
Existing partitions
Logical Volume Assignments
ENTAssign LV To Slot B?
HOLD Confirm
Slot A Slot B
- 7 -
Logical Volume 2/2 – Undefined Logical Volumes
LV=0 24GB GOOD 5A8C0CC43C1DBIF6
Existing logical volumes
LV=0 Not Defined ?
Undefined logical volumes
HOLDLG=A0 R5 DRV=3 1862GB GD S=0
ENT *G=A0 R5 DRV=3 1862GB GD S=0
LG=A1 R5 DRV=3 1862GB GD S=0
ENT *G=A1 R5 DRV=3 1862GB GD S=0
… Last member
Change Logical Vol Parameter
ENT
Name LV0
Write Policy Default
ENT HOLD ConfirmWrite Policy ----------------- Default Write-Back Write-Through
HOLDCreate in progress
Create Logical Drive?
HOLD
to select First member
Logical Volume Assignments
Redund Ctlr LG Assign to Slot B
Redund Ctlr LG Assign to Slot A
HOLD Confirm
HOLD ConfirmENT
ENTName: _
HOLD Confirm
to select, ENT to enter
HOLD
- 8 -
Host LUN
View and Edit Host LUNs
CHL=0 ID=112 Slot A
ENT
to select, ENT to enter
Edit Host ID/WWN Name List
ENT210000113329337AE Name
ENTAdd Host ID/WWN Name List
ENTAdd Host ID/WWN Name List ?
Del Host ID/WWN Name List
ENTDel Host ID/WWN Name List ?
HOLD Confirm
No Name List Create Name?
HOLDHost-ID/WWN Not Set
ENTHost ID _
Name- Not Set
ENTEnt Name _
HOLD Confirm
When there is no name list
HOLD Confirm
to select, ENT to enter
HOLD Confirm
to select
HOLD Confirm
Mapto Volume 5CE709170F0F0F10
CH0 ID112 Set1 No Mapped
ENTDelete CH0 ID112 LUN=0 Mapping ?
HOLD Confirm
ENTMap Host LUN
ENTLV=0 24GB GOOD 5A8C0CC43C1DB1F6
to select *LV=0 Part0 21GB
ENTMap Host LUN
?ENT
to select
HOLD
Confirm
ENT
- 9 -
Drive 1/5 – Members of a Logical Drive
View and Edit Drives
Slot=1 238214MB LG0 LN HDT722525
ENT ENTView Drive Information
ENTRevision Number: A96A
Serial Number: VDS41BT4E597HJ
Disk Cap(blks): 488386559
to select
Slot=12 ABSENTOpen Slot
Identify DriveENT
Flash All Drives ?
Flash Selected Drive ?
Flash All But Selected Drive ?
ENTFlash Drive(s) In Progress !
C=2 I=12 SES SAS-Exp 715X
Only drive information viewable
Dsk Rev. Space: 256 MB
Clone Failing Drive
ENTReplace After Clone
ENTReplace After Clone ?
Perpetual Clone
ENTPerpetual Clone ?
HOLDClone & Replace Successful!
HOLDClone & Replace Successful!
Spare drive available
Spare drive available
- 10 -
Drive 2/5 – Spare Drives
View and Edit Drives
Slot=1 238214MB LG0 LN HDT722525
ENT ENTView Drive Information
ENTRevision Number: A96A
Serial Number: VDS41BT4E597HJ
Disk Cap(blks): 488386559
to select
Delete Spare Drive
ENTDelete Spare Drive ?
HOLDDelete Spare Drive Successful!
Identify DriveENT
Flash All Drives ?
Flash Selected Drive ?
Flash All But Selected Drive ?
ENTFlash Drive(s) In Progress !
Dsk Rev. Space: 256 MB
ENTRemove Disk Reserved Space ?
HOLD
Drives unassigned to LDDisk Reserved Space Removed!
Media ScanENT
Priority Normal
ENTPriority Normal ? ----------------- Low Normal Improved High
HOLD
to select
Confirm
Iteration Count Single Time
ENTIteration Count Single Time ?
HOLD
Single Time Continuous
Execute Media Scan
ENTExec Media Scan
?HOLD Confirm
Abort Media Scan
ENTAbort Media Scan ?
HOLD2010/01/01 00:37 Critical
to scroll
Media Scan 12% □_______________
Scan in progress
View Media Scan Progress
ENT
Scan in progressMedia Scan 12% □_______________
Task Schedule List
- 11 -
Drive 3/5 – Spare Drives: Task Schedule
Task Schedule List
ENT2011/01/17 15:30 Global Spare Drv
Add Media Scan Task Schedule ?
No existing schedule
Existing schedules
to select
HOLDView Schedule Information
Add New ScheduleENT
Add Media Scan Task Schedule ?
Delete ScheduleENT
Delete the Task Schedule ?
HOLD Confirm
Exec on Init: NO
Start Date: 2011/01/17 15:30
ENT
Schedule Period Execute Once
Execution Mode: Concurrence
Priority: Normal
Select Target: Global Spare Drv
ENT
HOLDExec on Ctlr Init: NO
ENTExec on Ctlr Init: NO ?
HOLD Confirm
Yes No
Start date NOT SET
ENT[MMDDhhmmYYYY] _
to select, ENT to enter
HOLD Confirm
Execution Period NOT SET
ENT HOLD
to select
Confirm
Priority Normal
ENT HOLD
to select
Confirm
Select Target: NOT SET
HOLD Confirm
ENTAll Assigned Drives
Select a Drive NOT SET
ENTSlot=1 238214MB LG0 LN HDT722525
to select, ENT to enter
Execution Mode Concurrence
ENTExecution Mode Concurrence ?
HOLD Confirm
Sequence Concurrence
Priority Normal ? ----------------- Low Normal Improved High
to select
All Global Spare Drives
All Eligible Drives
HOLD Confirm
Execution Once ? ----------------- Once 1 secs … 8 weeks
HOLD
- 12 -
Drive 4/5 – Formatted Drives
View and Edit Drives
Slot=10 953609MB FRMT DRV Hitachi
ENT ENTView Drive Information
ENTRevision Number: A96A
Serial Number: VDS41BT4E597HJ
Disk Cap(blks): 488386559
to select
Add Local Spare Drive
ENTLV=0 R1 DRV=2 232GB GD SB=0
to select
HOLDAdd Local Spare Drive Successful
Add Global Spare Drive
ENTAdd Global Spare Drive ?
HOLDAdd Global Spare Drive Successful
Add Enclosure Spare Drive
ENTAdd Enclosure Spare Drive ?
HOLDAdd Spare Drive Successful!!
Identify DriveENT
Flash All Drives ?
Flash Selected Drive ?
Flash All But Selected Drive ?
ENTFlash Drive(s) In Progress !
Dsk Rev. Space: 256 MB
ENTRemove Disk Reserved Space ?
HOLDDisk Reserved Space Removed!
- 13 -
Drive 5/5 – Unformatted Drives
View and Edit Drives
Slot=1 238214MB LG0 LN HDT722525
ENT ENTView Drive Information
ENTRevision Number: A96A
Serial Number: VDS41BT4E597HJ
Disk Cap(blks): 488386559
to select
Add Local Spare Drive
ENTLV=0 R1 DRV=2 232GB GD SB=0
to select
HOLDAdd Local Spare Drive Successful
Add Global Spare Drive
ENTAdd Global Spare Drive ?
HOLDAdd Global Spare Drive Successful
Add Enclosure Spare Drive
ENTAdd Enclosure Spare Drive ?
HOLDAdd Spare Drive Successful!!
Identify DriveENT
Flash All Drives ?
Flash Selected Drive ?
Flash All But Selected Drive ?
ENTFlash Drive(s) In Progress !
Dsk Rev. Space: Unformatted
ENTFormat Disk Reserved Space ?
HOLDDisk Reserved Space Formatted!
Drives UtilitiesENT
Drive Read/Write Test
ENTView Read-Write Status Progress
ENTRW Test 12% □_______________
Abort Read-Write Test
ENTAbort Read-Write Test ?
HOLD
Confirm
- 14 -
Channel
CH0=Host ID=112 SXF=Auto
ENTSet SCSI Channel ID
View Channel Host-ID/WWN
View Device Port Name Lists(WWPN)
Data Rate
View and Edit Channels
ENT
CH2=Drv SXF=3.0G
ENTCHL=0 ID=112
ENTAdd Channel SCSI ID
ENTAdd CHL=0 ID=113
?HOLD NOTICE: Change
made to this setting will NOT take effect until the controller is RESET. Prior to resetting the controller, operation may not proceed normally.
to scroll
ENT
Delete Channel SCSI ID
ENTDelete ID=112
?
ENTID=0 WWNN 500D02300806905F
ENTWWPN 2100001B329337AE
ENT Set CHL-0 Data Rate to= 4.0G? ----------------- 4.0G 3.0G 2.0G 1.5G 1.0G Auto
to scroll
ENT
to select
ENT Confirm
5(D)=RCC SXF-3.0G
Fibre/iSCSI models
ENTAdd Host-ID/WWN Label ?
HOLDHost-ID/WWN Name Name_
to select, ENT to enter
HOLDWWPN(Name) 2100001B329337AE
NOTICE: Change made to this setting will NOT take effect until the controller is RESET. Prior to resetting the controller, operation may not proceed normally.
to select
to select
to select
to selectto select
Drive channels
RCC channels
Confirm
Host channels
( Optional )
- 15 -
Configuration Parameter 1/4 – Communication Parameters, Caching Parameters
Communication Parameters
ENTRS-232 Port Configuration
LAN IP Configuration
ENTCom1 Configuration
ENTBaud-rate 38400
Term Emul Enable
ENT
to scroll
ENTTerm Emul Enable ChangeTo Disab ?
HOLD Confirm
ENTL0[LAN] MA D0:23:08:8A:D4
ENTL0[LAN] IP 192.168.4.149
ENTView Statistics
ENTLink Operations: 100Mb/s(Full)
Transmit Packets 00099650
Receive Packets: 007F0D70
Collisions: 00000000
Transmit Errors: 00000000
Receive Errors: 00002524
Rcv Miss Packet: 00000000
View & Setup IP Address
IP Addr: 192.168.4.149
ENTInput Addr: _
HOLD
Confirm
ENT
to select, ENT to enter
NetMask: 255.255.0.0
Gateway: 192.168.1.253
Enable Disable
View and Edit Config Parms
ENT
V6 Addr: Disable
ENTV6 Addr: _
Baud-rate 38400 ChangeTo 2400 ? ----------------- 2400 4800 9600 19200 38400
PrefixENT
Prefix: _
RouteENT
Route: _
HOLD Confirm
to select, ENT to enter
to select, ENT to enter
to select, ENT to enter
Caching Parameters
ENTWrite-Back Cache Disabled
ENTEnable Write -Back Cache
Enabled Disabled
Period CachFlush Time-Disabled
Set Cache Flush Time-Disabled? ----------------- Disabled ConSync 30 secs 60 secs 120 secs 300 secs 600 secs
to select
HOLD
Confirm
HOLD
Confirm
ENT
Host-side Parameters
(In dual-controller models, all IP Address menus are divided into Slot A and Slot B.)
- 16 -
Configuration Parameter 2/4 – Host-side Parameters
Host-side Parameters
ENTMaximum Queued I/O Count-1024
LUNs per Host SCSI ID-8
Num of Host-LUN Connect-4
Tag per Host-LUN Connect-4
ENT
to select
HOLD Confirm
to select
HOLD ConfirmENT
to select
HOLD ConfirmENT
Set LUNs per Hos SCSI ID-8 ? ----------------- 1 2 4 8 16 32
Set Maximum Queu I/O Count-1024 ? ----------------- Auto 1 (Continues) 1024
to select
HOLD ConfirmENT
Set Num of Host- Connect-4 ? ----------------- 1 (Continues) 1024Set Tag per Host
Connect-4 ? ----------------- 1 (Continues) 256
Peripheral Dev Type Parameters
ENTDevice Type- Enclosure
ENT HOLD Confirm
Device Qualifier Connected
Support Removable Media-Disabled
LUN Application- First Undef LUN
Dev Qualifier? Support Not Conn
HOLD Confirm
Not Connected Connected
ENT
Enable ? Support Removable
HOLD Confirm
Disabled Enable
ENT
Set Device Type? Enclosure -----------------
No Device(0x7f) Direct-access(0)
Sequential(1) Processor(3)
CD-ROM(5) Scanner(6)
MO Device(7) Storage Array(c) Enclosure Dev(d)
Unknown(0x1f)
Applies to ? Undefine LUN-0’s
HOLD Confirm
Undefine LUN-0’s First Undef LUN
ENT
to select
Cyl/Head/Sector Mapping Config
Fibre ConOption- Loop Only
ENTSector Ranges Variable
Head Ranges Variable
Cylinder Ranges Variable
ENTSet/Change Cyl/Head/Sec ?
HOLD
Cyl/Head/Sec Values ----------------- Variable 1 2 (continues) 35 36
HOLD Confirm
to select
ENTSet Fibre ConOpt
Loop Only Ptop Only
Auto
to select
HOLD Confirm
Fibre host models
Drive-Side Parameters
Caching Parameters
- 17 -
Drive-Side Parameters
ENTMotor Spin-Up Disabled
ENTEnable Motor Spin-Up ?
Configuration Parameter 3/4 – Drive-side Parameters
Enabled Disabled
Disk Access Delay-60secs
ENT
to select
Host-Side Parameters
HOLD Confirm
HOLD Confirm
Drv I/O Timeout 30 secs
ENT
to select
HOLD Confirm
Set Disk Delay Time-No Delay? ----------------- No Delay 5 secs 10 secs (continues) 70 secs 75 secs
Maximum Tag Count-4
ENTSet Maximum Tag Count-Disabled ----------------- 1 2 4 8 16 32 64 128
to select
HOLD Confirm
Set SCSI IO Time ----------------- 7 secs ½ sec 1 sec (continues) 30 secs
Auto Rb Drv Swap Autochk-15 secs
ENT
to select
HOLD Confirm
SMART Mode- Disable
ENTSet SMART Mode ----------------- Disable Detect Perpetual Clone Clone+Replace Fail Drive
to select
HOLD Confirm
Set Drv Swap Chk Time-Disable ? ----------------- Disable 5 10 15 30 60
Auto Assign Global-Disabled
ENTEnable AutoAsgn Global Spare ?
Enabled Disabled
HOLD Confirm
Drv Delayed Write-Enabled
ENTDisable Drive Delayed Write ?
Enabled Disabled
HOLD Confirm
NOTICE: Change made to this setting will NOT take effect until the controller is RESET. Prior to resetting the controller operator may not proceed normally.
to scroll
HOLD
Disk Array Parameters
Periodic SAF-TE ChkTime-30secs
ENTSet SAF-TE Check Time-Disable ?
Enabled Disabled
HOLD Confirm
- 18 -
Configuration Parameter 4/4 – Disk Array, Redundant Ctlr, Controller Parameters
Disk Array Parameters
ENTRebuild Priority Normal
Verification on Writes
ENT HOLD
ENT HOLD ConfirmSet Rebuild Pri Normal ? ----------------- Low Normal ? Improved ? High ?
to select
to select
Max Drv Response Timeout-Disabled
Confirm
ENT HOLDSet Max Drv Rsp Timeout-Disable ? ----------------- Disable 160 ms 320 ms 960 ms
to select
Confirm
AV Opt Mode- Disabled
ENT HOLD
to select
Confirm
Logical drive available
Controller Parameters
ENTController Name: Not Set
ENTEnter Ctlr Name: _
HOLD Confirm
LCD Title Disp- Logo
ENT HOLD ConfirmLCD Title DispIn Name ?
Passwd Validation Timeout-Always
ENT HOLD
Ctlr Unique ID (Hex) – 88AD4
ENTCtlr Unique ID (Hex) - _
Set Controller Date and Time
ENTTime Zone
Date and Time
ENTGMT +00:00 GMT _
ENTMMDDhhmmYYYY _
Redundant Ctlr Configuration
ENTRC Communication Channel-SATA
Cache Sync on WtThru-Enabled
Adaptive Write Policy-Disabled
ConfirmENT HOLDDisable Cache Sync on WtThru ?
ConfirmENT HOLD
ConfirmHOLD
ConfirmHOLD
Enabled Disabled
Enable Adaptive Write Policy ?
Enabled Disabled
to select, ENT to enter
Name Logo
to select
Confirm
to select, ENT to enter
to select, ENT to enter
to select, ENT to enter
Redundant controller models
HOLD Confirm
Passwd Validation ----------------- Disable 1 min 2 mins 5 mins Always
PasswdValidation ----------------- Disable 1 min 2 mins 5 mins Always
Set AV Opt ? Disabled ----------------- Disabled Fewer Streaming Multiple Streami
- 19 -
Peripheral Device 1/2 - Device Status, Device Entry
View and Edit Peripheral Dev
View Peripheral Devices Status
ENTRedundant Ctlr Failback Complet
ENTDevice Set 0
ENTPower Supply
Cooling Fan
Temperature Sensor
Drv Fail Output Definition
ENTPSU0 Normal
ENTCooling fan0 Low
ENTBackplane Temper 25.0(c) HT: 60.0
Slot 1 CH2 ID0
to select
to select
to select
Device Set Descriptor
ENTIFT DS S12F-G1433
to scroll
ENT
I2C Periph Dev Operational
Redundant controller models
Voltage Sensor
ENTPSU0 +5V 4.5V
to select
Set Peripheral Devices Entry
ENTForce Primary ctlr Failure ?
Force Secondary Ctlr Failure ?
ENTRedundant Ctlr Primary Failback
HOLD Confirm
HOLD Confirm
Event Trigger Operations
ENT
CBS Low/Failed Disabled
ENTCBS Low/Failed Enabled?
Power Supply Failed Disabled
ENTPower Supply Failed- Enabled?
Fan Failed- Disabled
ENTFan Failed Enabled?
Temp Over Limit- Disabled
ENT HOLD Confirm
Redundant controller models
Enabled Disabled
Enabled Disabled
Enabled Disabled
Temp Over Limit ----------------- Disabled Enabled Down in 2 min (Continues) Down in 1 hour
to select
Ctlr Failure- Disabled
ENTCtlr Failure Enabled ?
Enabled Disabled
ENT
Adjust LCD Contrast
- 20 -
Peripheral Device 2/2 – LCD Contrast, Device Configurations
Set Peripheral Devices Entry
Adjust LCD Contrast
Ctlr Peripheral Device Config
ENTLCD Contrast: □□□□□□_______
ENTView Ctlr Periph Device Status
Temperature and Voltage Parms
ENTVoltage Monitor
ENT
ENTTemperature Monitor
ENT Trigger Threshold for ----------------- 3.3V Event 5V Event 12V Event CPU Temp Event Ctlr Temp Event
ENTUpper for 3.3V Event-Def (3.3V)
Lower for 3.3V Event-Def (2.9V)
[+3.3V] 3.384V Operation Normal
[CPU] 45.0°C In Safe Range
to adjust
to select
ENTRange 3.4V-3.9V Input:_
Upper CPU Temp Event-Def (90°C)
Lower CPU Temp Event-5°C
Voltage
Temperature
ENT
to select, ENT to enter
ENTRange 2.6V-3.2V Input:_
to select, ENT to enter
ENT
to select, ENT to enter
ENT Range 0°C- 20°C Input:_
to select, ENT to enter
Range 50°C- 100°C Input:_
HOLD Confirm
HOLD Confirm
HOLD Confirm
HOLD Confirm
to select
to select
- 21 -
System Functions
Mute BeeperENT
Change Password
Reset This Controller
Shutdown This Controller
Controller Maintenance
ENTMute Beeper
?
Old Password: _
ENT HOLDNews Password: _
Re-Ent Password: _
HOLDChange Password Successful !
HOLD
Reset This Controller ?
ENT HOLD
Shutdown This Controller ?
ENT HOLDShutdownControll Is Busy !
Shutdown Complet Reset Ctlr ?
HOLD
Export NVRAM to reserved space
ENT
Impor NVRAM from reserved space
View Update FirmwareStatus
Export NVRAM to reserved space ?
HOLD HOLDExport NVRAM is progress !
Export NVRAM is completed !
ENT HOLDImport NVRAM Is Progress !
NOTICE: Change made to this setting will NOT take effect until the controller is RESET. Prior to resetting the controller operator may not proceed normally.
Firmware is not Updating
ENT
System Function
Import NVRAM ----------------- include passwd ? except password ?
HOLD Confirm
to select, ENT to enter to select, ENT to enter to select, ENT to enter
Confirm
Confirm
to scroll to scroll
Update status
HOLD
Logical drive available
Logical drive available
- 22 -
View and Edit Event Logs
33:NOTICE:NVRAM Restore From
ENTClear Below Event Log ?
ENT HOLD
View System Information
Total Cache Size 1024MB
ENT
Firmware Version: 3.85A.02
Boot record Version: 1.15A
Serial Number: 7927165
CBM: Present
Base Board Rev. ID: 0
Base Board ID: 9C
ID of NVRAM V1.13.154
Ctlr Position Slot A
System Information / Event Logs
Confirm
2010/01/01 00:37 Notification
HOLD
to scroll
to select
Clear Below Event Log
HOLD ENT
SN-Slot A: 7758538
SN-Slot B: 7758536
Single controller model
Redundant controller model
Redundant controller model