Er-II User Manual
-
Upload
alberto-solis -
Category
Documents
-
view
223 -
download
0
Transcript of Er-II User Manual
-
7/28/2019 Er-II User Manual
1/14
-
7/28/2019 Er-II User Manual
2/14
PRECAUTIONS 4
PREFACE 6
OVERALL VIEW 6
DISPLAY & KEYBOARD 7
INSTALLATIONS 8
OPERATIONS 10
1. Programmi00ng Mode 10
Chapter 1. Basic Operation 11
Chapter 2. PLU Saving & Calling - up 13
Chapter 3. User's Set-up Mode 15
2. Sales Mode 17
Chapter 4. Sales Transaction 18
ERROR MESSAGES 22SPECIFICATION 22
CONTENTS
-
7/28/2019 Er-II User Manual
3/14
4 5
PRECAUTIONS WARNING
Precautions when installing the scale. To ensure that you get the most fromyour scale, please follow these instruction.
Make sure to plug your scal into the proper power outlet. For maximumperformance, plug into a power outlet 30 minutes before the usage for warmup.
Do not disassemble the scale.
When any damage or defect occurs,
contact your CAS
authorized dealer
immediately forproper repair.
Do not overload beyond the maximum
weight limit.
Do not pull the plug by its cord when
unplugging. Damaged cord could cause
electric shock or fire.
To prevent from fire occurring, Do not
place or use the scale near flammable or
corrosive gas.
Avoid placing the scale near heater
or in direct sunlight.
Scale must be grounded to minimize
electricity static. This will minimize
defect or electric shock.
Insert plug firmly to wall outlet to
prevent electric shock.
Use proper Adapter. Incorred adapter
could damage the scale.
To reduce electric shock or incorrect
reading, Do not spill water on the scale
or place it in humid condition.
Warning
For consistent and accurate reading,
maintain periodical check by your
CAS authorized dealer.
Avoid sudden shock to the scale.
Internal mechanism could be damaged.
Place the scale on firm and temperature
consistent environment.
Take the battery out when scale is not in
use for long time. Leakage from the
batteries is hazardous.
Keep the scale away from other
electromagnetic generating devices.
This may interfere with accurate
reading.
Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instruction.
Correct type of battery
Grab on the bottom of the scale when
moving. Do not hold by the platter.
Attention
By adjusting 4 corners of the scale, set
the scale even using the built in scale
leveling indicator.
-
7/28/2019 Er-II User Manual
4/14
76
PREFACE
OVERALL VIEW
Thank you for purchasing your CAS ER scale.
CAS scales are designed and produced under rigid quality control to deliver
outstanding performance, reliability and long life.
This manual will help you with the proper operation and care of your new CAS ER.
Please review the ER scale manual before you use the scale and keep it handy for
future reference.
DISPLAY & KEYBOARD
LCD STANDARD TYPE : Front Display
LCD STANDARD TYPE : Rear DisplaySTANDARD TYPE
POLE TYPE
-
7/28/2019 Er-II User Manual
5/14
98
KEYBOARD
Table : Symbols on Display
SYMBOLS DESCRIPTION
( ) Weight steady
( ) To adjust zero
( ) Tare on
( ) Backlight on
( ) Low power warning
Table : Key Functions
KEYS FUNCTIONS
INSTALLATIONS
1. Insert the post pipe into a post bracket as Fig. 1
2. Insert and fasten two display assembly screws as Fig. 2
Fig. 1 Fig. 2
POSTPIPE
POSTBRACKET
BOLT
Numbers import
Direct PLU keys
Function key, PLU restore,P mode (User s Set-up Mode enter)
To make several sales transaction by adding up
To Clear data
To set zero
To set up or clear tare value
To turn on/off the scale or backlight(LCD version only)
-
7/28/2019 Er-II User Manual
6/14
-
7/28/2019 Er-II User Manual
7/14
12 13
Chapter 2. PLU Saving & Calling-upd. Tare functionTare means the weight of container. You may use tare function when you weighan item with container and measure only the weight of item.
One time tare
Place a container on the platter. EX)200g oftare.
Press tare key to set zero point. EX)200g oftare.
1. Saving unit price on PLU
This section explains how to save unit price in PLUCan pre-store 4 PLU valueCan clear data inputted before
Press key for few seconds to enter thePLU 's state can be preestablish
Press number key to input unit price you wishto have. EX)1.99Successive tare
Place another container on the platter.EX)100g of tare
Press tare key to set zero point
Successive tare
Press tare key to save the number andbegin to set the next PLU Press key again to exit to the common mode
After weighing item remove all of thecontainer from the platter.
Press tare key again to set zero.
-
7/28/2019 Er-II User Manual
8/14
-
7/28/2019 Er-II User Manual
9/14
1716
Press tare key to move to the next function:Auto power-off time
This section explains how to set Auto power-off time function.
b. Time of Auto power-off
Functions Options Remarks
1 5 Auto power-off after 1 5 minutes whe n no use
3 0 Auto power-off after 3 0 minutes whe n no use
6 0 Auto power-off after 6 0 minutes whe n no use
12 0 Auto power-off after 120 mi nute s when no use
Press zero key to select option. E.G set theauto power-off time be 30 minutes.
Press tare key to set the next function:backlight on/off function
This section explains how to set backlight on/off function
c. Backlight on/off function
Functions Options Remarks
3 Autom ati c ba ckl ight- off w he n not i n use for 3 se conds
5 Autom ati c ba ckl ight- off w he n not i n use for 5 se conds
1 0 Autom ati c ba ckl ight- off w he n not i n use for 1 0 se conds
ON Backlight always on
OFF Backlight always off
Press zero key to select option. E.G to setto turn off the backlight after 5 seconds
Press key to exit to common mode.
2. Sales mode
Chapter 4.Sales transaction
a. Input the unit price through the number key
b. Input the unit price through calling up the PLU
c. Add up the total amount
d. Inspect or clear the total amount
-
7/28/2019 Er-II User Manual
10/14
1918
Chapter 4. Sales transaction
ER-series price scale can provide direct number inputting mode or PLUinputting mode.
a. Input the unit price through the number keyThis section explains how to input the unit price through the number key,and complete the Sales transaction
Place an item on the platter and pressappropriate numeric keys to input unit price.EX) 1.99 for unit price.
Remove the item from the platter.
Press M1 ~ M4 key can call up the PLUEX) M 1
Remove the item from the platter
Place an item on the platter
b. Input the unit price through calling up PLU
Press M 1 ~ M 4 key to call up thePLU directly. E.G M1
Place an item on the platter
c. Add up the total amount
Press add key to make the adding-up transactionsYou may either call up PLU to input the unit price
Press add key Remove the item from the platt
-
7/28/2019 Er-II User Manual
11/14
2120
Input the unit price through the number keyEX) 2. 99 for peanut dessert
Place the item on the platter
IPress add key. Total price displaysays total price added. And unit displaysays the number of sales transactions added
Remove the item from the pl atter
You can also place the item on the platter first, and then input the unit price
The maximal adding-up times is 255, and the maximal total price is 999,999
Press add key to inspect the total amount.E.G total amount=115.00. total numberof transaction=5
Press 0 ~ 9 key to exit to commonmode. E.G press 0 keyClear the total amount
d. Inspect or clear the total amount
Check the total amount
Checking total acount.
Press add key to inspect the total price.E.G total amount=115.00, total numberof transaction=5
Press delete key to clear the total amount,and exit to the common mode
-
7/28/2019 Er-II User Manual
12/14
-
7/28/2019 Er-II User Manual
13/14
-
7/28/2019 Er-II User Manual
14/14
26
MEMO