Equipment Book - April 2013
-
Upload
clayman-supplies-limited -
Category
Documents
-
view
231 -
download
9
description
Transcript of Equipment Book - April 2013
Wheels & Equipment Book
A range of wheels and equipment carefully chosen for the discerning
potter, ceramicist or sculptor
No. 3
where quality comes as standard
April 2013
Choosing a piece of equipment
Buying any large piece of equipment is difficult and fraught with problems. These notes are offered as a guide to overcome problems experienced when choosing equipment such as lack of experience or knowledge of what is available. It is important in our eyes to match each individual’s desire with their budget to effectively get the best value for money.
Budget is almost always the driving force behind the decision you will make. Sometimes it may be prudent to wait until you can afford the best rather than compromise on the immediate need. Generally we would argue that purchasing a piece of equipment, such as a potter’s wheel should be for life. If you think you will buy cheap and then trade up, it is probable that you will be disappointed or be conscious during use that the equipment has shortcomings. However, we would never try to argue that the cheapest model is the worst and the dearest is the best. Whatever the price, it is important to match the equipment to the user and the intended use.
Each section has a description of the equipment detailed within that category. If applicable reasoning notes are also added to aid making your choice.
EQUIPMENT DELIVERY The logistics of delivering equipment is often overlooked. You must be aware how your equipment will arrive and what you may be responsible for. We would like to make all customers aware of what is included in the services we offer.
PALLET DELIVERY
This service can be applied to the delivery of wheels, pugmills or any piece of equipment with external dimensions no greater than a metre square. The equipment is strapped to a pallet and delivered by means of a lorry with a tail lift. These vehicles normally have a pallet truck that can be used to manoeuvre the pallet on flat ground, but it must be appreciated that the price given is to deliver to site and off-load.
It is the customer’s responsibility to remove the kiln or equipment from the pallet and move into position.
Nabertherm Kilns are delivered by DHL pallet delivery service. The drivers will only off-load to the nearest convenient point. (Note: If a delivery driver offers to help further they are not covered by insurance and you are accepting responsibility for any damage that may occur to property or the equipment.)
DELIVER, OFF-LOAD INTO POSITION
This is more of a tailored service and covers all sizes and shapes of equipment. Again, it is delivered by vehicle with a tail-lift. The vehicles will always have a pallet truck and the driver will off-load and move the equipment into position. A survey is requested to give the carrier information on the surfaces and site to be encountered. This service includes negotiation of no more than one step measuring 4”. Delivery of heavy equipment cannot be guaranteed on uneven or soft terrain. For large or relatively unstable equipment, assistance is requested from the customer. This service is not available to all UK locations.
Call us on: 01243 265845 2
Wheels What wheel to buy?
Buying a potter’s wheel should be an exciting process, but it can also be intimiating. There are a number of variables you need to consider before making your decision. Potter’s wheels can come in many forms. The following details the different types of wheels available.
Kick or Power? Kick:
Benefits DrawbacksLittle maintenance required (just the greasing of bearings). Not easy to use, especially for a beginner.
Choice of stand up or seated. Not portable.
Not much cheaper than the cheapest power wheel.
There are two types of kick wheel; geared or momentum (the momentum is normally by having a very heavy wheelhead).
As demand for has fallen away we now longer offer any form of kick wheel in our range.
Power:
Benefits DrawbacksChoice of 3 drive systems: Cone, Electronic (Belt drive) and Electronic (Direct drive).
Portabililty depends on the seating arrangement - wheels without seats will tend to be lighter and more portable that wheels with seats.
Choice of stand up, seated or a seat as an optional extra.
Types of Power Wheel:
Cone or Electronic?
The best known and probably biggest manufacturer of cone driven wheels was Shimpo. However, Shimpo have now ceased to manufacture cone wheels and have replaced all cone models with the “Whisper” range. As the cost of electronic wheels have fallen to a similar price for the best cone wheels we too have discontinued the supply of this format and now we only supply electronic wheels.
In our view, torque (the measured ability of a rotating element) is better on electronic wheels and the transition of speed on electronic will always be smoother, especially at slower speeds (cone wheels can loose torque at very slow speeds and become jerky).
Drive Systems
Electronic wheels work by varying the voltage to motor to vary the speed and all the electronic wheels we supply now use the safe AC motor in conjunction with inverter control systems
Belt Drive Direct DriveAll Brtish built power wheels are run on belt drive systems: That is to say all the low-format and standard-format power wheel we supply - Bailey, Knightsbridge, Lincoln Electronic, Craftsman, Fitzwilliam and Wealden Throwing Wheel.
All American and Australian built power wheels are run on direct drive systems. That is to say all the extra-low format power wheels we supply - Shimpo Whisper range, Artists Table Top Wheel and Venco Direct Drive wheels.
Direct drive eliminates the use of drive belts and bearings and therefore reduces the build cost.
When replacement of worn parts is required, repair costs are greater than belt driven electronic wheels as the direct drive motor has to be dismantled. This should always be carried out by competent qualified engineers.
The drive system of cone wheels is by friction. This is a metal cone against a rubber drive ring.
Email us on: [email protected] 3
7143
- Sh
impo
Whi
sper
T
7137
- Sh
impo
RK3
D
7122
- Sh
impo
RK3
E
7144
- Sh
impo
RK5
T
7112
- Sh
impo
RK5
5
7135
- Ba
iley
7125
- Kn
ight
sbrid
ge
7128
- C
rafts
man
7129
- Fi
tzw
illia
m
7120
- St
affo
rshi
re
7121
- Li
ncol
n E
lect
roni
c
Extra Low Format 4 4 4 4 4
Low Format 4 4 4 4 4
Standard Format 4
Seat - available as optional extra 4 4
No seat 4 4 4 4 4
Integral Seat 4 4 4 4
Bench mountable or table top 4 4 4
Additional legs (to increase height) - availabe as optional extra
4 4
Splash Tray (without drain hole) 4 4 4 4 4 4 4 4 4
Splash Tray (with drain hole) 4 4
Removable Splash Tray 4 4
Split Splash Tray 4 4 4 4 4
Rotation: Counter clockwise/clockwise 4 4 4 4 4 4 4 4 4 4
Roatationl: Counter clockwise 4 4
Fixed foot pedal 4 4 4 4
Floating Pedal 4 4 4 4 4
Cordless Pedal
Hand control lever 4 4 4
Removable Wheelhead 4 4 4 4 4 4 4 4 4 4
Fixed Wheelhead 4 4
AT-A-GLANCE GUIDE TO THROWING WHEEL FEATURES
Original electronic wheels using DC motors and speed controls could be slightly jerky at 0-5 r.p.m., but this problem should not be found on any of the electronic wheels we now offer.
It is strongly advised that if any wheel is attached to old wiring (i.e. without circuit breakers) a plug in RDC type circuit breaker is used between the plug and the socket. Especially with DC motors.
Format
Format refers to the size and ergonomics of design:
Extra Low Format: Bench mounted or with the addition of short legs.Low Format: A height of just below waist height when standing by the wheel.Standard Format: Provides a seating position where the thrower’s feet cannot touch the ground.
Casing
Casings can be made from wood or have an angle iron frame with a plastic casing and pressed sheet metal. The sheet metal casing acts as a sound box. Wooden cases tend to deaden sound made by the wheels.
Additions
Some wheels will accept acessories to aid a specific process. Batt holding wheelheads or studded wheelheads can be fitted to some wheels.
Call us on: 01243 265845 4
Extra-Low Format Wheels
7137 - SHIMPO WHISPER RK3D
The RK Whisper represents the next generation of potter’s wheels. Responsive, high torque at all speeds, powerful and quiet. The exterior of the RK Whisper resembles the discontinued RK10, but that is where
the similarities end! This new wheel features a brushless DC motor and direct drive (no belt) system. The motor is electronically controlled and
operated by a fixed foot pedal and hand lever. It is reversible and the steel body is durable under all conditions. A 12” wheelhead and
two-piece splash pan are included as standard features.
Technical Data: Motor: 0.5hp, 400w, AC230v, 60Hz
Drive System: Direct drive DC Brushless MotorSpeed Control: Fixed foot pedal w/hand lever
Wheelhead speed: 0-250rpmWheelhead direction: Clockwise/Counter-clockwise
Wheelhead: 12in. diameter alloyDimensions: 500mm long x 525mm wide x 500mm high approx
Weight: 60kg
7122 - SHIMPO WHISPER RK3E
Shimpo have combined the advanced technology of the RK Whisper and the popular features of the Velocity V75 potter’s wheel to create the VL
Whisper. Responsive, high torque at all speeds, powerful and extremely quiet. This wheel can also be used as a bench mounted wheel by
detaching the legs.
Technical Data:Motor: 0.5hp, 400w, AC230v, 60Hz
Drive System: Direct Drive DC Brushless MotorSpeed Control: Remote Foot Pedal
Speed range: 0-250 rpmWheelhead direction: Clockwise/Counter clockwise
Wheelhead: 14” alloyDimensions: 578mm long x 687mm wide x 569mm high approx
Weight: 60kg
A new economy version of the Shimpo Whisper range. Offering a range of fantastic features at the price of other budget wheels. Made to
Shimpo’s normal high standard, the Whisper T offers the beginner the opportunity to acquire a wheel that has the specification
demanded by professionals.
Technical Data:Motor: 300w, AC230v, 50Hz
Drive System: Direct drive DC Brushless Motor with electric speed control
Speed Range : 0-250 rpmSpeed Control: Remote foot pedal
Wheelhead Direction: Clockwise/Counter clockwiseWheelhead: Light alloy casting, 300mm diameter
Dimensions: 750mm x 572mm x 580mmWeight: 53kg
7143 - SHIMPO WHISPER T
Email us on: [email protected] 5
7112 - SHIMPO RK55 WHEEL
Shimpo’s RK-55 is a bew “budget” wheel.
Technical Data: - Up to 12kg centring capacity
- Three-leg design increases stability. - Built-in worktable for tools and pots.
- Two-Piece Splashpan- Remote foot pedal
- Modular design for compact storage.- 1.8m power supply cord
- Two Year Warranty for Peace of mind.
Motor: 1/8 HP 100WDrive System: DC Motor with Brush
Wheelhead Speed: 0-250RPMWheelhead Direction: Clockwise/counterWheelhead: 300mm/12” light alloy casting
Dimension: W560 x D720 x H540mmWeight 23kg
Call us on: 01243 265845 6
Low Format Wheels7135 - BAILEY
The Bailey Electronic Wheel offers the studio and professional potter a wheel of unparalleled performance and versatility in a compact and user
friendly design. The wheel is powered by a super smooth 0.5hp motor that is controlled by a computer enhanced VF drive that, due to its unique design, can generate up to the peak equivalent of 1hp under heavy loads.
This enables the wheel to give constant smooth power throughout the speed range and is extremely quiet in operation.
The wheel is completed by its remote foot pedal which is fitted as standard.
Technical Data:Motor: 0.37Kw (1/2hp) AC industrial constant rated motor.
Splash tray: Moulded plasticWheelhead: 12in. dia aluminium
Construction: Precesion laser steel chasis with powder coated finish.Speed range: 0-280 rpm
Speed control: Remote foot pedalDimensions: 630mm long x 470mm wide x 680mm high approx
Weight: 30kg
7125 - KNIGHTSBRIDGE
The Knightsbridge Wheel has been designed and developed using extensive experience and research into control systems. It uses a 0.37kW
(1/2hp) motor which is controlled by the same control unit used in our more expensive wheels. This provides unrivalled power and torque in a wheel of this size and offers an extremely quiet and smooth operation.
The wheel is completed by its remote foot pedal which is fitted as standard and the wheels ability to reverse rotation at the flick of a switch.
Truely an excellent wheel at a fantastic price.
Technical Data:Motor: 0.37Kw (1/2hp) rubber mounted motor single phase
Splash tray: Moulded polypropeleneWheelhead: 12in. dia
Construction: Steel cabinetSpeed range: 0-300 rpm
Speed control: Remote foot pedalDimensions: 630mm long x 470mm wide x 680mm high approx
(excluding seat)Weight: 40kg
7121 - LINCOLN ELECTRONIC
The Lincoln Electronic Wheel has been developed to provide a throwing wheel with unrivalled power. It is a low format design, constructed using a steel chassis with fibreglass outercase. The splash tray is made from
moulded polypropulene. A strong .5hp motor powers the latest designed electronic speed control, enabling a smooth transistion of speed and
unbeatable torque across the speed range of 0-280rpm. A unique feature is the ability to reverse the direction of rotation at speed by the flick of a
switch. A 12in. wheelhead is fitted as standard together with a fully adjust-able padded seat. There is also facility to adjust the tension of the foot
pedal for comfort and maintenance of pre-set speeds.
Technical Data:Motor: 0.37kW (.5hp)
Bearings: Axial ball bearing sealed for lifeSplash tray: Moulded polyproylene
Wheelhead: 12in. diameter aluminiumConstruction: Electrical welded steel chassis with mould fibreglass body
Speed range: 0-280 rpmDimensions: 530mm wide x 1060mm long x 685mm high approx.
Email us on: [email protected] 7
• LOW FORMAT DESIGN• INTEGRAL SEAT
• ELECTRONIC SPEED CONTROL• MULTI-ROTATIONAL
• EXCELLENT SPEED RANGE 0-280r.p.m. approx.• SUPERB TORQUE
• EASY REMOVABLE SPLASH TRAY
The Craftsman Wheel is a design favoured by many leading craft potters in the U.K. It is constructed using a polished wooden cabinet
complete with a moulded fibreglass splash tray. The drive mechanism is extremely smooth, offering low noise and vibration, whilst
still produing excellent torque. Large amounts of clay can be thrown with ease and the wheel head is multi-rotational at the flick of a switch.
7128 - CRAFTSMAN
• LOW FORMAT DESIGN• INTEGRAL SEAT
• ELECTRONIC SPEED CONTROL• MULTI-ROTATIONAL
• EXCELLENT SPEED RANGE 0-280r.p.m. approx.• SUPERB TORQUE
• EASY REMOVABLE SPLASH TRAY
The Fitzwilliam Throwing Wheel is a another design favoured by many leading craft potters in the U.K. It is constructed using a polished
wooden cabinet complete with a moulded fibreglass splash tray. The drive mechanism is extremely smooth, offering low noise and vibration,
whilst still producing excellent torque. Large amounts of clay can be thrown with ease and the wheel head is multi-rotational at the flick of a
switch.
7129 - FITZWILLIAM
Call us on: 01243 265845 8
Standard Format Wheels7120 - WEALDEN THROWING WHEEL
The Wealden Throwing Wheel is designed and constructed to give long trouble free service for the professional or amateur potter. This wheel is constructed using a polished wooden cabinet complete with a shelf
and a two position adjustable upholstered seat, the wheel incorporates a large moulded plastic bowl. The drive mechanism is extremely smooth and offers low noise and vibration characteristics whilst giving excellent torque response so enabling large amounts of clay to be thrown. Fully
reversible wheelhead. Optional extras include Easy-lift Wheelhead and batts.
Technical Data:Motor: 0.5hp
Voltage: 220v/240v 5OHz single phaseSpeed: 0-280 rpmWheelhead: 12”
Double sealed top bearing for extended lifeSplash Tray: Moulded plastic
Size: 680mm wide, 820mm high, 1000mm longWeight: 70kg (unpacked)
Wheel Accessories
PLYWOOD WHEELBATTS
Circular batts made from high quality selected exterior ply for exceptional warp resistance. Can be attached to the wheelhead using a pad of clay,
locating pins(batts would need holes drilling). Sizes available:
7149 - 8” 7153 - 9”
7150 - 10” 7154 - 11” 7151 - 12” 7156 - 13” 7152 - 15”
ALLOY WHEELHEAD
Spare wheelheads that can be fitted to Bailey, Knightbridge, Lincoln, Craftsman and Fitwilliam wheels. Type of shaft needs to be specified when
ordering.
7140 - 10” 7141 - 12”
STUDDED WHEELHEAD
Spare wheelheads that can be fitted to Bailey, Knightbridge, Lincoln, Craftsman and Fitwilliam wheels. Type of shaft needs to be specified when
ordering.
7140 - 10” 7141 - 12”
7168 - EASY-LIFT WHEELHEAD
A specialised wheelhead that can be fitted to the Bailey, Knightbridge, Lincoln, Craftsman and Fitwilliam wheels. Plywood batts are inserted to enable flatware to be made easily and removed on the batt without
movement.
Email us on: [email protected] 9
Extruders7500 - CLAYPRESS
7510 - NORTH STAR EXTRUDER PACKAGE
Here are the simplest, safest extruders available for small to medium extrusions - the kind most of us do most of the time. They have proved
their utility and durability year after year.
North Star extruders do not look like or work like any others. They are designed to be simple, safe and inexpensive. Both models feature a 4
inch square steel barrel tapered at the top for easy loading. Each comes with a long extension handle to give extra
leverage for small extrusions or stiff clay.
The Claypress extruder is built as a robust compact piece of equipment for the most demanding of artist or craftsman. It is designed to give trouble free use with a minimum amount of
maintenance. The Claypress will extrude simple forms such as coils, handles etc., but can also extrude hollow sections. Coil and hollow dies are available as optional extras. The wall-mounting bracket is made from aluminium, which is cast in a series of hooks on which
the handle is placed to operate the plunger. The barrel is made of 3” diameter steel tubing to which the die holder is attached by means of
quick release clips for ease of die changing.
Dimensions:Height: 530mm approx.Width: 140mm approx.
Length: 155mm - 720mm (with handle extended) approx.Weight: 6kg approx.
Construction: Aluminium body, steel barrel, steel handle, aluminium plunger
7501-Optional Hollow Die Set
7503-Optional Coil Die Set
Call us on: 01243 265845 10
PugmillsWhat is a Pugmill?
Traditionally, clay was prepared by wedging and kneading. Wedging was the art of mixing dfferent consistencies of clay to form a uniform mass. Kneading was the final preparation of the clay to remove air pockets and develop the plasticity of the clay body. This is still done in many countries but a pug mill can make the task easier and quicker than the traditional manual method. Approximately one hour of pugmill use will produce enough pugged clay for an average professional potters’ days work.
A pugmill is used to blend clay to restore it to a more uniform ‘workable’ consistency. This applies to new clay or clay scraps from previous work. Clay is loaded into the feed hopper and an internal auger chops and mixes the clay, pushing it along the barrel before recompressing the clay and forcing it out the nozzle. The de-airing models incorporate a vacuum pump which removes air trapped within the clay whilst pugging is performed. This produces the highest quality clay for immediate use on a potter’s wheel. Tradtionalists can still argue that kneading will still produce a better clay and also a “feel or knowledge” of the clay body to the user.
The hopper mouths and nozzle should always be covered with plastic when not is use to avoid the clay in the barrel from drying out. Ideally the barrel of any pug should be cleaned out once a year.
7600 - 2” MINI WITH HOPPER
The economy range of pugmills has been specifically designed for the studio and classroom environment. They are compact and lightweight making them easily transportable. This model is fitted with a hopper
safety grid and thermal overload safety switch as standard.
Technical Data:4” (100mm) Aluminium Body
2” (50mm) Extrusion Body and nose cone for easy cleaningIndividual nylatron blades mounted on a hexagonal steel shaft
Geared motor reduction driveSingle or three phase
Safety switch and overload starterOutput 190-200kg per hour approx.
Overall DimensionsHeight: 470mm approxWidth: 280mm approxLength: 800mm approxWeight: 36.5 Kg approx
7600/MS - 2” MINI WITH MICRO-SWITCH
This model has the same specification as 7600, but it is fitted with a interlocked hopper safety switch. This switch, together with its high torque motor, makes the pugmill extremely easy to load as there is no safety grid in the hopper to impede the flow of clay. When the loading handle is raised the machine switches off and then on again when the loading handle is lowered. Thermal overload safety switch is fitted as standard.
7601 - 3” MINI WITH HOPPER
7601/MS - 3” MINI WITH MICRO-SWITCH
The same specification as the 7601 version , but is fitted with a interlocked hopper safety switch negating the need for a hopper grid.
The same compact design as the 2” Mini, but has a larger 150mm barrel with a 75mm (2in.) outlet. This version has a greater output and, due to its larger hopper, is easier to use than the smaller 2” model. A thermal
overload switch is fitted as standard.
Technical Data6” (150mm) aluminium body
3” (75mm) extrusion body and nose cone for easy cleaningIndividual aluminium blades mounted on a hexagonal steel shaft
Geared motor reduction driveSingle or three phase
Safety switch and overload starterOutput 300kg per hour approx
Overall DimensionsHeight: 500mm approxWidth: 280mm approxLength: 800mm approxWeight: 78kg approx.
Email us on: [email protected] 11
7620 - 3” VERTICAL
This vertical pugmill has a 150mm split aluminium barrel with a 75mm outlet and individual alloy blades mounted on a hexagonal shaft. It
offers superior performance over conventional horizontal pugmills, but has the advantage of only taking up a 60cm x 60cm foot print. The pugmill is sturdily mounted on its own stand,
which only requires securing to a suitable floor.
Technical DataDrive: 0.75kW (1hp) with helical reduction gearbox
Construction: All aluminium body 150mm in diameter with a 75mm out let, fitted with Alloy blades mounted on a hexagonal shaft with taper
roller bearings, split body for easy cleaning.Thermal over load starter with safety interlocked switch
Output: 360kg per hour
Overall DimensionsDepth: 711mm approx.Width: 609mm approx.
Height: 1980 mm approx.Weight: 123kg approx.
7625 - 4” VERTICAL DE-AIRING
The 100mm (4” ) vertical pugmill is extremely powerful and robust with the ability to handle all types of clays. The main body is manufactured
from aluminium, with an auger, also made up of individual alloy blades. The auger is mounted through two taper thrust bearings and is driven via a flexible coupling by a 1.1kW (1.5hp) helical geared motor, with a final drive output of 18rpm. It is fitted with a safety interlock switch
which eliminates the need for a grid in the loading hopper and is supplied with a separate nose cone that is pre-drilled to enable the use
of die plates for coil extruding.
Technical DataVoltage 220—240 V, 50 Hz Single phase, 380— 415 V, 50 Hz Three
phase.Output: 700kg per hour approx.
Overall Dimensions:
Length: 760mm approx.Width: 760mm approx.
Height: 2300mm approx. Weight: 300kg approx.
Call us on: 01243 265845 12
7627 - TILE EXTRUDER
The tile extruder is a very versatile machine, besides extruding tiles, mouldings and coils etc can be extruded with the use of optional die plates. Using the standard 100mm dia. nose cone supplied with the
machine enables other shapes, such as hollow forms to be extruded, again with the use of optional die plates. The tile extruder is a purpose
designed machine for the extrusion of tiles. It has been designed around the standard de-airing pugmill, but using a larger higher torque motor gearbox unit. The machine is also fitted with a completely new
nose cone outlet designed to enable tiles of approximately 280mm width by up to 25mm thick to be extruded. Smaller and /or thinner tiles
can also be extruded by the use of accessory die plates fitted to the front of the nose cone.
Technical Data:
Construction: All aluminium alloy construction with split body to aid easy cleaning. Individual aluminium alloy blades mounted on a hexagonal shaft. Supplied with all switch gear and an interlocked
hopper safety switch.Motor gearbox unit: 2.2kW (3hp) single or three phase
Vacuum pump: High pressure rotary vane oil immersed –28” (-1 Bar)Bearings: 2 adjustable taper roller bearings, oil seal and retaining
plate.Output: 60 -80 sq ft/ hour approximately. Output depends on clay body
condition (softness), tile dimension, number of operators etc. With standard nose cone fitted out put is rated at 500kg per hour.
Overall Dimensions:Length: 905mm approx.Width:609mm approx.Height: 1040mm approx.Weight: 270kg approx.Standard accessories:- 1- 150mm x 5mm die plate
Optional extras: Extruding table,
Ware boards, Tile Cutting System, Die plates, Stainless steel auger
7627/1 - TILE CUTTING TABLE
This cutting table has been designed to compliment the tile extruder pugmill. The cutting system comprises a table with formica top. A central rotary shaft secured by sealed roller bearings, which are
adjustable to allow for different thicknesses. On the shaft are mounted sixteen cutting discs. As the wareboard of extruded clay is pulled by
the operating lever, the cuttings discs are pulled through the clay.
7627/2 - EXTRUDING TABLE
Another addition to compliment the tile extruding pugmill. The table consists of a rigid base supporting a fully adjustable top. The adjustment allows for varying thicknesses of extrusion. On the suraface of the table is a paper roll, which allows extrusion to run without buckling.
Overall Dimensions:
Length: 1830mm approx.Width: 510mm approx.
Height: 600mm variable
7333 - BIN DOLLEY
The easiest way to move bins of clay or glaze around the workshop. Adjustable
to suit most size of bin.
4901 - PLASTER SINK
Every potter’s workshop will have reclaim clay. The problem the potter
faces is how to deal with the process of recycling this product. With the plaster sink the reclaim can be spread within
the sink to dry. The walls retain the clay whatever its condition (liquid or otherwise) from spilling. Our plaster
sink is the simple and tidy way to control your reclaim before pugging.
Email us on: [email protected] 13
Slab Rollers
7210 - SLAB ROLLER 3’ & 7211 SLAB ROLLER 4’
The Clayman Slab Roller has been designed to provide extremely efficient and reliable methods of producing slabs of clay for hand
building or tiles. It has been designed using vast experience in slab roller production and incorporates a rack and pinion drive system, eliminating the need of maintenance from troublesome wire driven systems, the design allows for infinitely variable thickness of clay to be rolled by means of adjustment of the main roller using a simple threaded adjuster that allows for fine adjustment whilst keeping the
equal distance above the table across its length. The large single roller is made of a rust proof material to avoid corrosion or
contamination of the clay. The slab roller has fully collapsible legs so it can be easily transported and comes complete with a set of high
quality rolling cloths
7210 - Technical Data:Overall Dimensions:
Size: 1090mm high x 820mm wide x 920mm longSlab Size: 720mm long x 470mm wide
Weight: 60kg
7211 - Technical Data:Overall Dimensions:
Size: 1090mm high x 820mm wide x 1220mm longSlab Size: 1020mm long X 470mm wide
Weight: 70kg approx
Please note slab size can only be given as a approximation due to the different natures of clay used.
7214 - MOTORIZED SLAB ROLLER
The Motorised slab roller is fully automatic , the operator simply places the clay on the slab roller adjusts to the required thickness
closes the interlocked safety cage and then presses the cycle button . The slab roller will then make two passes over the clay and then come
to a complete stop.
It is labour saving i.e. whilst the clay is being rolled it leaves you free to proceed with other duties around the class room or studio,
extremely safe in operation , out standing results are produced from the combination of constant pressure at a set speed , ideal for the
handicapped or physically impaired.
The slab roller uses the same excellent standard of engineering as our other slab rollers. The main roller is manufactured from
corrosion resistant alloy and has infinite adjustment between approximately 2mm and 30mm via a centrally mounted threaded adjusting handle, thus eliminating the need for packing boards.
Technical Data:
Drive: 0.37 Kw (0.5 Hp) worm reduction 1 phase or 3 phaseSpeed control: Variable speed with full logic control
Safety: Fully enclosed and electrically interlocked safety cagePower supply: 220/240 v50Hz/60Hz 380v 415 v
Slab size: 1020 mm x 470 mm wideDimensions : 1200 mm high x 915 mm wide x 1220 mm long
Weight: 90 Kilos
Call us on: 01243 265845 14
Our spray booths are suitable for glaze and slip spraying. 7801 is designed to be ducted to the atmosphere, the other models are self contained units.
Spray Booths
7801 - DRYBACK SPRAY BOOTH
This Spray Booth has been designed for use in the classroom or small pottery workshop. The booth is fitted with a 12” electric extractor fan which produces an air velocity of 250 cfm at the face. A stand and
washable heavy duty filter are fitted as standard.
Technical data:Spray Booth
Width: 24” (610mm) approx.Height: 24” (610mrn) approx,Depth: 35.5” (890mm) approx.
StandWidth: 24”(610rnrn) approx.Depth: 18” (450rnm) approx.Height: 30” (900mm) approx.
Power supply: 220/240v l phaseWeight: 21Kg approx.
NOTE:Only suitable for water based material
7800 - WATERFALL SPRAY BOOTH
This Waterfall Spray Booth has been designed to meet the ever increasing need to protect our environment. The water wash spray
booth works on the principle of a curtain of continuous recycling water running down the rear face of the spray booth, a glaze spray is aimed towards this curtain, the spray being guided by a powerful extraction fan, the glaze is trapped by the water curtain, whilst the air stream is pulled through the booth and into a washable stainless steel pre filter
and finally into a washable filter bag. The excess glaze is washed into the tank and can at a later date be
reclaimed depending on the type and colour of the glaze. There is a ball valve to allow the water to be drained and the contents of the tank
removed. Any glaze materials can also be removed and disposed of safely. The booth is mounted on four castor wheels. The 7800 is primarily designed to be used by the studio potter and educational faculties for low volume production, therefore the booth does not need ducting to atmosphere making it portable around the studio
environment.
This spray booth uses a sophisticated baffle system to prevent water take through into the filter bag, they are designed to be used with water based material only, but can be adapted if required for solvents. If the
spray booth is to be used in a production environment it may be necessary to duct to the atmosphere, please
contact our technical department is you require further advice.
Technical data:Height: 1580mm approx.Width: 820mm approx.
Depth: 1290mm approx.Fan: 2000CFM
Air extraction: 250 Cu Ft/minSteel construction
Internal parts: stainless steelWater tank: Polypropylene
Switchgear: Thermal overload protectionWeight: 118 kg approx.Power: 220/240v 5OHz
Hood internal dimensions: 638mm x 625mm x 420mm deep.Working depth: 350mm
Email us on: [email protected] 15
7805 - WATERFALL SPRAY BOOTH
This Waterfall Spray Booth has been designed to meet the ever increasing need to protect our environment. The water wash spray
booth works on the principle of a curtain of continuous recycling water running down the rear face of the spray booth, a glaze spray is aimed towards this curtain, the spray being guided by a powerful extraction fan, the glaze is trapped by the water curtain, whilst the air stream is pulled through the booth and into a washable stainless steel pre filter and finally into a washable filter bag. The excess glaze is washed into the tank and can at a later date be reclaimed depending on the type and colour of the glaze. There is a ball valve to allow the water to be
drained and the contents of the tank removed. Any glaze materials can also be removed and disposed of safely. The booth is mounted on four castor wheels. The 7800 is primarily designed to be used by the studio potter and educational faculties for low volume production, therefore the booth does not need ducting to atmosphere making it portable
around the studio environment.
This spray booth uses a sophisticated baffle system to prevent water take through into the filter bag, they are designed to be used with water based material only, but can be adapted if required for solvents. If the spray booth is to be used in a production environment it may be neces-
sary to duct to the atmosphere, please contact our technical depart-ment is you require further advice.
Technical data:
Height: 1580mm approx.Width: 820mm approx.
Depth: 1290mm approx.Fan: 2000CFM
Air extraction: 250 Cu Ft/minSteel construction
Internal parts: stainless steelWater tank: Polypropylene
Switchgear: Thermal overload protectionWeight: 118 kg approx.Power: 220/240v 5OHz
Hood internal dimensions: 638mm x 625mm x 420mm deep.Working depth: 350mm
6998 - GLECO TRAP
The Gleco Trap is an innovative, inexpensive solution in preventing clay and glaze materials blocking waste pipes. The system easily
fits most standard sink cabinet areas and is easily maintained. Recommended for light to medium use.
The Gleco Trap is easily installed. The trap is connected below the sink and collects solids in a bottle, which has a fill line. when the
solids reach the fill line, the trap is drained through a valve, the bottle is exchanged with a replacement bottle, the valve shut and the trap is
back in service. Bottle exchange is rapid and done without the need of tools (less than 2 minutes).
6999 - CLAY TRAP
The Clay Trap measures 552 x 400 x 270mm deep. The cut-away lid in our illustration reveals the two weirs, the inlet on the left and the
outlet, which has a 76mm water seal on the right. Both inlet and outlet have coupling nuts for joining to 38mm ‘Vulcathene Mechanical’ pipe.
Recommended for medium to heavy use.
Call us on: 01243 265845 16
Spray Equipment6800 - BASIC SPRAY GUN
Simple but effective spray for modelling, stencilling, texturing
and ceramics, for spraying medium to heavy viscosity fluids, and simple enough for children
ages 8 and up. Sprays 18mm - 50mm by adjusting the tip.
Supplied in a blister pack. The pack includes 22ml jar, vinyl hose and regulator. It can be used from
a propellant can in conjunction with the regulator, or from a
compressor (.25” adaptor required – optional extra) or a deflating
car tyre (valve adaptor required – optional extra).
6803 - TYRE ADAPTER
An adaptor to enable the connection of an air brush regulator to a car tyre valve. The tyre must be on the rim and requires inflating. The spray
operates by deflating the tyre.
6801 - MINI SPRAY GUN
Simple but effective spray for modelling, stencilling, texturing and
ceramics for spraying medium to heavy viscosity fluids, and simple
enough for children ages 8 and up. Sprays 18mm - 50mm by adjusting the tip. The pack includes 120ml
jar, vinyl hose and regulator. It can be used from a propellant can in conjunction with the regulator, or from a compressor (.25” adaptor
required – optional extra) or a deflating car tyre (valve adaptor
required – optional extra).
This item is the same as 6800 with the exception of the jar size.
6804 - 0.25” ADAPTOR
An adaptor that enables a .25” air hose, used with airbrushes and the Basic and Mini Spray Guns to be
connected to a compressor.
6808 - AIR PROPELLANT 750g
750ml can of propellant for use with airbrushes or the Basic and Mini Spray Guns.
6602 - DEFYNIK COMPRESSOR & SPRAY GUN
An economy combination of 6601 Junior Spray Gun with 6600 777
Compressor. A continuous diaphragm type compressor with a suction spray
gun, including a 1 litre capacity jar. Spray Gun includes a round spray and
fan spray nozzle.
6601 - JUNIOR SPRAY GUN
• Pressure gun (low pressure).• With continuous air outlet.
• Maximum pressure: 3,5 bar.• Pressurized tank and internal mixture aircaps.
-• Air consumption: 85 l/min.-3,5 bar.• Weight: 650 g
A well proven suction type spray gun, offering a round spray and fan spray nozzle. Ideal for
spraying large areas of glaze.
6606 - IWATA POWERJET COMPRESSOR
6609 - SAGOLA JUNIOR G SPRAY GUN
Light and economical gravity spray gun, high trans-fer and very low air consumption. Robust, light and with new ergonomic design.
• Gravity Spray Gun • With Air Valve • Single shaft design, less parts• Low air consumption• Maximum robustness and reliability• Designed for working at pressures under 3.5 bar (50psi)
Iwata Studio Compressors are powerful, compact and quiet. With oil-less pistion motors, they are low maintenance and affordably priced. The Power Jet Plus Handle Tank compressor, like its name suggests, has the feature of a 480cc air tankinside the handle. It is powerful enough to run up to four airbrushes (a multiple-oulet manifold is required) or a small spray gun.
Email us on: [email protected] 17
6608 - PAINTEC SPRAY GUN
Introducing the new Paintec hand operated spray gun. The simple but cost effective way to spray glaze and colours. The Paintec Sprayer has
been developed especially for potters, with the finest quality plastic and bronze components to assure chemical resistance.
What makes this item stand out?•ECONOMICAL•ADJUSTABLE
•SPRAYS CONTINUOUSLY•NO COMPRESSOR REQUIRED•NO POWER SUPPLY REQUIRED
•LIGHT & COMFORTABLE TO USE
The Sprayer is supplied with a 0.6mm nozzle as standard, which enables glaze to be sprayed that has passed through an 80’s mesh
sieve and colour that has passed through a 120’s mesh. Larger nozzles are available as optional extra. How to use the Paintec Sprayer? Simply pump four or five times to start to spray, then
pump from time to time to maintain a continuous pressure thanks to an exclusive stainless steel retention valve. The pressure pump is
designed to obtain maximum pressure with minimal effort. NO POWER SUPPLY REQUIRED
No electricity or batteries are required. It can be used anywhere, at any time and is very quiet in use. Although it is not necessary to use
the Paintec with a compressor it is possible to connect to a compressor if required (optional extra).
6608/3 - PAINTEC NOZZLE SET
Nozzle Set contains 0.8mm, 1.0mm and 1.2mm nozzles.
6608 - PAINTEC SPRAY GUN
The perfect way to convert the Paintec Spray Gun for use with a compressor
6608/11 - PAINTEC SMALL CONTAINERS
Additional small containers supplied in packs of three. These are used with the Paintec Spray Gun to enable small amounts of colour to be
sprayed.
6608/7 - PAINTEC SPARE BOTTLE & CAP
A spare 1 litre jar for the Paintec Spray Gun. Supplied with screw on cap to enable jar to be used for storage of glaze or colour.
Call us on: 01243 265845 18
Whirlers can also be known as Banding Wheels. they are metal turntables that are used on a work top to aid the decoration and making of ceramics. Alloy whirlers are lighter and easy to transport, therefore especially good for modelling. Steel whirlers are heavy and ideal for banding lines onto plates or bowls as they will spin for longer. All whirlers have concentric circles etched into the working surface to aid “re-centring” of work in progress. Also very useful in a Spray Booth for turning pireces that are being sprayed.
Whirlers
6700 - 6706 - WHIRLERS
6700 - 8 x 4” STEEL WHIRLER
6701 - 8 x 6” ALLOY WHIRLER
6704 - 8 x 3” ALLOY WHIRLER
6705 - 10 x 4” ALLOY WHIRLER
6706 - 12 x 6” ALLOY WHIRLER
6711 - 6712 - WHIRLERS
6711 - 20 x 7cm CAST IRON WHIRLER
6712 - 25 x 7.5cm CAST IRON WHIRLER
6709 - ADJUSTABLE MODELLING STAND
A inexpensive simple modelling stand. The height is easily adjusted and the “head” turns freely. Also included is a useful tool rest.
Email us on: [email protected] 19
Miscellaneous EquipmentDAMP CABINETS
The construction of these damp cabinets is zinc coated sheet steel, which is powder coated externally. The doors are fItted with neoprene
seals and lockable handles. Each cabinet includes four removable shelves. To obtain a moist atmosphere the base can be lined with
damp plaster blocks (not included).
7700 - Technical Data:Size: 1220mm wide x 1220mm high x 610mm deep
Weight: N/A
7701 - Technical Data:Size: 910mm wide x 1220mm high x 610mm deep
Weight: N/A
7702 - Technical Data:Size: 1220mm wide x 1830mm high x 610mm deep
Weight: N/A
7703 - Technical Data:Size: 910mm wide x 1830mm high x 610mm deep
Weight: N/A
DRYING CABINETS
These Drying Cabinets are designed to aid the drying of moulds and clay ware. Each cabinet is constructed of zinc coated steel with two vertical hinged front opening door.. All Drying Cabinets have a on/off temperature control switch and can be operated from a 13amp supply.
Technical Data:Supply: 3kW -220v/240v - 5OHz single phase
Size: 1830mm wide x 1220mm high x 575mm deepWeight: N/A
SLABBING & WEDGING BENCHES
Our benches are specifically designed for classroom and studio use. They are made from sustainable environmentally friendly materials and are a robust design to withstand years of use. The benches are
finished to a high standard with attention to detail being paramount to ensure long life and ease of use.
7164 - SLABBING BENCH
Technical Data:Construction - Soft wood frame sanded and polished to a high finish.
Bench top - 20mm Formica top Dimensions - 1200mm long x 860mm x 760mm high
Note: “H” design stiles available on request
A professional wedging bench, which incorporates the same quality wooden frameas our work benches, but incorporates a compressed
concrete top. Ideal for wedging and kneading clay
7166 - WEDGING BENCH
Technical Data:Construction - Soft wood frame sanded and polished to a high finish.
Bench top - 50mm compressed concrete Dimensions - 1200mm long x 660mm x 760mm high
Note: “H” design stiles available on request
Call us on: 01243 265845 20
Mixers7001 - RAPID MIXER
A simple item of workshop equipment designed for the speedy mixing of glazes or slips. In use water is placed in the container, followed
by the mixer. The dry materials are added while the mixer is turning. The mixer has a 1/6hp motor driving a stainless steel shaft and vaned alloy impeller. A handle is fitted for ease of lifting. The rapid mixer is
supplied with 25litre plastic container.
N.B – If using to mix any material of high viscosity (i.e. casting slip) the mixer should be running before inserting into the material.
Technical Data:
Size:Diameter :55mmHeight: 610mmWeight: 25kg:
7007 - VIBRATORY SCREEN
An electrically operated screen for slip or glaze. Fitted with 8” (204mm) diameter mesh. Three sizes of mesh are available 60, 80 or 120 mesh.
Technical Data:
Overall size:Width: 365mm approx.Depth: 458mm approx. Height: 508mm approx.
Weight: 9kg approx.Electrical Supply: 220/240v Single Phase
Email us on: [email protected] 21
Plaster Working Equipment7714 - REVERSIBLE TURNING LATHE
This lathe is an invaluable addition to the mould makers workshop. A .5hp motor transfers drive to the shaft via a V belt and pulley. The speed is controlled by a AC electronic speed control, which has a reversible facility. The machine is totally enclosed for safety and is
supplied complete with an adjustable tool rest.
Technical Data:Motor: .5hp AC
Speed control: Variable electronicSpeed range: 0-380rpm
Bearings: Sealed for life, self-aligningSize: 410mm high x 470mm wide x 1220mm long
Weight: 90kg (approx.)
Optional extras: Foot operated controlTapered steel spindles: 150mm, 230mm, 300mm and 380mm
Aluminium face plates: 150mm, 200mm, 250mm diameter
7722 - MODELLING BENCH
This Modelling Bench is constructed of a sturdy rectangular steel frame and is driven via a variable speed electric motor. A speed range
of 0-250rpm with high torque is available. A 12” plaster prong or 12” wheelhead is supplied with each bench.
Technical Data:
Overal Dimensions: 600mm (wide) x 750mm (deep) x 800mm (high) to Bench bed or 900mm (high) to top of wheelhead
Overall to top of Shaving Guard when fitted(Optional Extra): 1170mmMotor: 0.37kW AC
Speed Control: AC InverterVoltage: 230
Speed: 0.250rpmWeight: 90kg approx.
7720 - VACUUM PLASTER MACHINE
Technical Data:
Capacity: 3-5 gallonsDrive unit: 0.37kW geared drive, output
speed 500rpmShaft: Stainless steel shaft and bronze
bladesSize: 1.9m high x 720mm deep x 650mm
wideWeight: 140kg (approxx.)
Optional extras: Blending jugs, visual indicators for time duration
7721 - PLASTER BLENDER
The Plaster Blender mixes plaster quicker and more
efficiently than by hand and produces a more consistent
plaster mix. The blender is free standing and has a mixing head driven by a 0.37kW inline motor
and gear unit. The mixer is raised or lowered by means of a counter balance guide platform. Each blender is supplied with a switchgear and a timer unit allowing for automatic cut off after a pre-determined mixing
period.
Technical Data:
Capacity: 3-5 gallonsDrive unit: 0.37kW geared drive, output
speed 500rpmShaft: Stainless steel shaft and bronze
bladesSize: 1.9m high x 720mm deep x 650mm
wideWeight: 140kg (approxx.)
Optional extras: Blending jugs, visual
indicators for time duration
Optional Extras: Shaving Guard
Tool Rest
Call us on: 01243 265845 22
Slip Equipment7300 -15 gallon BLUNGER - 7304 - 25 gallon BLUNGER
Blunging is the process of producing casting slip from plastic or powdered clay. This model uses two paddles which rotate at 150rpm approximately on a stainless steel shaft. Drive is via a 0.75kW motor
through a reduction gearbox. The drum is fibreglass fitted with a extended loading shute for safety. A stand is available as a optional
extra.
Technical Data:
7304 - 25gallon BLUNGER - Technical Data:Overall Dimensions: 800mm wide x 1000mm deep x 1100mm high
approx.Weight: 50kg
Capacity: 25gallons
7310 -SLIP CASTING CENTRE
This design is the 7311 Slip Pump fitted into a self-contained fibreglass tank. Removable wooden casting rails are fitted for ease of mould
draining. The whole unit is mounted on castors. A drain plug at the bottom of the tank is for emptying and cleaning.
Technical Data:Overall Dimensions: 530mm wide x 1040mm deep x 1140mm high
Weight: 22kg
7311 -SLIP PUMP
The Slip Pump is a highly versatile method of slip dispensing for both studio and hobby ceramics. The pump uses a rotary vaned design
capable of giving a good, even flow. The pump also has an agitating effect to maintain usable conditions. A syphoning action can also be
used to aid the draining of moulds.
Technical Data:Overall Dimensions: 300mm wide x 300mm deep x 800mm high
Container Capacity: 10gallonsMotor & Switch: 0.5hp single phase
Weight: 14.5kg
Email us on: [email protected] 23
Notes
Call us on: 01243 265845 24
Notes
Email us on: [email protected] 25
1. PaymentCredit is allowed to Education Authorities and similar bodies and will be allowed to other customers on receipt of acceptable trade and bank references. Payment of accounts is to be made within 30 days nett of invoice date. NON-PAYMENT WITHIN THE THIRTY DAYS WILL BE SUBJECT TO AN INTERST CHARGE. Unless otherwise agreed, where no credit account exists, all orders must be accompanied by remittance to the value of the order including carriage and VAT. Payment may be made by cash, cheque, credit or debit card.
2. PricesAll goods are invoiced at prices ruling at date of despatch and are accepted only on this basis. All prices are subject to change without notice. All prices printed in price lists, advertising matter and elsewhere, submitted in writing or stated verbally are, unless otherwise stated, nett ex-works, carriage and VAT extra.
5. Delivered GoodsAlthough we make every effort to adhere to stated delivery times, such times do not bind us and we shall be under no liability for any loss or damage of whatever nature caused by delay.
4. CarriageOff-loading and moving into position is the responsibility of the customer unless special arrangements have been made.
3. QuotationsQuotations for the delivery of goods, equipment and kilns will be submitted on receipt of all relevant information.
8. Description & SpecificationAll descriptions, specification, drawing or illustrations shown in literature as advertising matter, given verbally or in writing are given for general guidance only and no warranty or guarantee of any kind is to be implied nor is such information to form part of any contract.In accordance with out policy of constantly improving products we reserve the right to change specification or delete any items from our catalogue, without prior notice. THE BUYER IS STRONGLY RECOMMENDED TO TEST ALL GOODS BEFORE USING THEM AND WHERE A BULK MATERIAL IS TO BE USED IT IS RECOMMENDED THAT A SAMPLE BE TESTED FIRST.
6. Non-Delivery/ Partial LossIn the event customers must give notice in writing to the carrier and ourselves within three days of receipt of goods.
7. DamageIf possible, goods should be examined in the presence of the deliveryman and if any package appears damaged, the consigment/ delivery note should be endorsed accordingly. Customers must advise the carrier in writing of any damage within three days of delivery and present a detailed claim to the carrier within seven days of delivery, with copies to ourselves.
9. LiabilityWe accept no liability for death, injury or damage if any kind whether to person or property arising out or in connection with any material, goods or services by us.
10. OwnershipThe ownership of goods bought shall not pass to the Purchaser until the Purchaser has paid to the Company the total purchase price, including VAT, in respect of said goods.
Contact detailsPostal Address:
Clayman Supplies LimitedMorells BarnPark LaneLower Bognor RoadLagnessChichesterWest SussexPO20 1LR
Telephone & Fax Numbers:
Telephone: 01243 265845 (24 hour ansaphone)Fax: 01243 267582
Internet:
Email:General Information: [email protected]: [email protected] queries: [email protected]: www.claymansupplies.co.uk
Conditions of Sale
Call us on: 01243 265845 26