EPIC STEEL 3’ DELTA RIB
Transcript of EPIC STEEL 3’ DELTA RIB
10
3’ DELTA RIBE P I C S T E E L
3’ D
ELTA
RIB
6574 H w y 10 West | M issoula, MT | 406.542.1711
3’ DELTA RIB TRIMMATERIAL SPECIFICATIONS
LOAD TABLES
3’ DELTA
RIB
11
Made in Montana - Refer to Color Chart for Color Availability
Span (ft.)
Three or More Span Condition
28 Gauge & 80 ksi
LL(S) LL(D) OUTWARD(S)
3 41.2 36.7 39.2
4 23.2 15.5 22.1
5 14.8 7.9 14.1
• 1 ½” Bearing Length• Load Span Tables Based on Working Stress• Flexural Design analysis according to AISI “Specification for the Design of
Light Gauge Cold-Formed Steel Structural Members” May 1981• Continuous Span Loading applies to sheets continuous over three or more
spans• Weight of sheet has not been allowed for when calculating live load and
Uplift.• Deflection (L/180) limiting live load based on deflection of span.• Metal thickness based on minimum ASTM specifications for allowable load
calculations• Loads may be increased by 1/3 for wind loads
Areas of discontinuity are subject to higher spikes in wind pressure, therefore a different coefficient in wind pressure will need to be considered and multiplied by a factor of 1.5
Data from: 1994 UBC Table 16-F
Note: The load tables have been compiled for the design of steel roofing and siding used in conjunction with either wood or steel framed structures. EPIC Steel assumes no responsibility, either expressed or implied, for its use.
Minimum Slope Requirement: 3:12
Screw Application: #10 Wood grip fasteners are designed for use with dimensional lumber, #14 Wood grip fasteners are designed for use with plywood sheeting, OSB, and wafer wood (7/16” minimum thickness). #12 Tek screws are designed to be used with structural steel up to 3/16” in thickness.
Roof Application: Fasteners to be applied along side every rib and attached to each purlin, 2’ on center. Please note that it is the responsibility of the builder to ensure that purlins are adequately spaced to meet specific engineering requirements.
EPIC Steel is neither partially nor solely responsible for improper installation or defects as a result of installation.
APPLICATION DETAILS
Gauge: 28, 26
Weight: 1.98 lb. /LF, 2.67lbSteel Yield Stress: 80,000 psiGalvalume Steel Gauge, AZ-50
Paint System: Stormshield Xt-40, Energy Star® Rated, Silicone Modified Polyester
Warranty: 40 Years
Available Material Type:Painted, Galvalume®
Gauging System: Epic Steel follows the national A.I.S.I. (American Iron and Steel Institute) specifications manual for tolerances in galvanized sheet metal.
All gauges conform to ASTM A792 and ASTM A653 Grade E (80,000 min. yield)/ or Grade D (50,000 min. yield) unless otherwise designated at time of order.
w w w.EPICsteelcorp.com
SNA
P LO
CK3’ DELTA RIB STANDARD TRIM
12
3’ D
ELTA
RIB
STA
ND
ARD
TRI
M
pitch &paint
4”
4”
Endwall
3½” paint
11⁄16”3½”½”
Sidewall
½”
½”
paint
pitch
45⁄16”
1½”
Standard Ridge Cap
paint
11⁄16”
½”
½”
35⁄8”
X = 4¼”X = 6¼”
X
Gable
28 GA.(10’1” / Stick)
Eave
paint
pitch
2”
½”
XX = 3½”X = 5½”
Outside Corner
paint
11⁄16” 11⁄16”
4½” 4½”
½”¾”
Upper Transition
63⁄8”
6½”
paint
pitch
Lower Transition
63⁄8”
6½”
pitch & paint
Style-D Eave
½”
2”
3”
1”
paint
pitch
High Eave
½”
X
4¼”
X = 4¼”X = 6¼”
paint
pitch
Mini Gable
½”
11⁄16”
½”
2”
4”
paint
W-Valley
XX = 9”X = 17”X = 19.5”
X1”
paint
3¼”17⁄8”
1¼” ¾”
paint
Snow Stop
3/4” J-Metal
17⁄8”
7⁄8”
7⁄8”
½”
paint
F+J 3/4” x 3/4”
13⁄16”
¾”7⁄8”
27⁄16”
25⁄16”
19⁄16”
paint
F+J 1/2” x 3/4”
13⁄16”
½”7⁄8”
2”1½”
25⁄16”
paint
6574 H w y 10 West | M issoula, MT | 406.542.1711
3’ DELTA RIB STANDARD TRIM
13
3’ TUF RIB
3’ DELTA
RIB STAN
DA
RD TRIM
13
28 GA.(10’1” / Stick)
Wainscott
15⁄8”
1½”7⁄8”
paint
Square Base
11⁄16”13⁄16”
13⁄16”
11⁄16”
paint
Angle Base
17⁄8”
1¾”
7⁄8”paint
L-Base / Drip Cap
1½”
½”1”
paint
28 GA.(10’1” / Stick)
Inside Corner
paint
11⁄16”
11⁄16”
4”
4”
¾”
¾”
Mini Door Jamb
55⁄8”
1½”
1”
paint
Standard Door Jamb
7½”
1½”
1”
paint
Open Jamb
paint
5½”
1½”
Double Track Cover
5½”
67⁄8”
13⁄8”
¾”
paint
Single Track Cover
5¾”
3”
1¾”
1¼”¾”
paint
w w w.EPICsteelcorp.com