UNITED STATES ENVIRONMENTAL PROTECTION AGENCYWASHINGTON, B.C. 20460

&EPA Office of Pesticide Programs

_• „ ,. SEP 27 2011Troy Corporation8 Vreeland RoadFlorham Park, N. J. 07932

Attention: Adrian KrygsmanDirector, Product Registration

Subject: Grotan i

EPA Registration No. 365-76Notification Dated August 24, 2012

This will acknowledge receipt of your notification, submitted under theprovisions of FIFRA Section 3(c)(9).

Proposed Notification

-Additional Brand Name: "Mergal 17411"

General Comment

Based on a review of the submitted material, the following comments apply:

The Notification is in compliance with PR Notice 98-10 and is acceptable.This information has been made a part of your file.

If you have, any questions concerning this letter, please contact me at (703)308-6217.

Sincerely,

Marshall SwindellProduct Manager 33Regulatory Management Branch 1Antimicrobials Division (751 OP)

G r.Please read instructions on reverse before completing form. Form Approved, OMB No. 2070-0060. Approval expires 05-31-S

EPAUnited States

Environmental Protection AgencyWashington, DC 20460

D Registration

D Amendment

RI Other:

OPP Identifier Number

xxxxxxApplication for Pesticide - Section I

1. Company/Product Number365-76

4. Company/Product (Name)

Grotan

2. EPA Product ManagerM. Swindell

PM#33

3. Proposed Classification

[H Restricted

5. Name and Address of Applicant (Include ZIP Code)Troy Chemical Corporation c/oTroy Corporation8 Vreeland RoadFlorham Park, N.J. 07932PLEASE SEND ALL CORRESPONDENCE TO

"CONTACTPOINT"LISTED BELOW

I I Check if this is a new address '

6. Expedited Review. In accordance with FIFRA Section 3(c)(3)(b)(l), my product is similar or identical in composition and labelingto:EPA Reg. No.

Product Name .

Section -II

I ] Amendment - Explain below.I I Resubmission in response to Agency letter dated.

|2^ Notification - Explain below.

Explanation: Use additional page(s) if necessary. (For Section I and Section II.)

Notification of Alternate Brand Name

LJ Final printed labels in response to Agency letter dated.|~| "Me Too" Application

LJ Other - Explain below

Section -11. Material This Product Will Be Packaged In:Child-Resistant Packaging

D Yes*D No

*Certification mustbe submitted

Unit Packaging

D YesD NoIf'Yes"Unit Packaging wgt.

No. percontainer

Water Soluble PackagingDYes

D NoIf Yes"Package wgt.

No. percontainer

2. Type of ContainerG MetalEH Plastic

n Glass

I I Paper

l~l Other (Specifly)3. Location of Net Contents InformationI I Label I I Container

4. Size(s) Retail Container 5. Location of Label DirectionsI I On Label

I I On labeling accompanying product6. Manner in Which Label is Affixed to Product J D Lithograph

EH Paper gluedD Stenciled

D Other.

Section - IV

1. Contact Point (Complete items directly below for identification of individual to be contacted, if necessary, to process this application̂Name

Adrian KrygsmanTitle

Director, Product RegistrationTelephone N6F(incfu£|e AreaCode) °cc%„„ 973-443-4200. X2249

Certification \I certify that the statements I have made on this form and all attachments thereto are true, accurate and complete. Iacknowledge that any knowingly false or misleading statement may be punishable by fine or imprisonment or bothunder applicable law.2. Signature

CX^-Ax<—- rfa*\£/"4. Typed Name "

Adrian Krygsman

3. Title L C *

Director, Product Registration

c c cc

c c

u cI

c c < c t

16. Date«App!icationReceived'

/Stamped)

5. Date

08/24/2012

c c c c c o

o c <-C C t

EPA Form 8570-1 (Rev. 8-94) Previous editions are obsolete , White- EPA File Copy (original) Yellow- Applicant Copy

C ^^ "' C

TROY CORPORATION

August 24, 2012 Via Courier

Document Processing Desk (NOTIF)Office of Pesticide Programs (7504P) 'Antimicrobial Division (AD)U.S. EPARoom S-4900, One Potomac Yard2777 South Crystal DriveArlington, VA 22202-4501 - / •

Attention: Mr. Marshall Swindell .PM33 ' . ' • - . ' . ' .

RE: GrotanEPA Reg. No. 365-76Submission of Alternate Brand Name (ABN)

Dear Mr. Swindell:

Troy Corporation is submitting this notification of an alternate brand name for theproduct referenced. We enclose the following documents for this purpose:

• EPA Form 8570-1 Application for Registration• MB £2.) copies .'of the Master Label• Certification per PR Notice 98-10

r

The alternate brand name for this product is "Mergal 174H"

Please contact me directly should you have any questions concerning this action.I can be reached via email or phone attaTgsmaa@Trovcorp.com or 973-443-4200,X2249, Thank you. ' • • ' . . .

Adrian KrygsmanDirector, Product Registration % cl

c c c c c. . ' • . ' ' t I

. - . . . ' c c t • c c

8 Vreeland Road • PO Box 955 • Florham Park, NJ 07932-0955Tel 973-443-4200 Fax 973-443-0258

c c'toI

MERGAL 17411A long lasting Broad Spectrum Bactericide, and Fungicide for the

Preservation of Adhesives, drilling additives, Metal Cutting Fluids andCoolants, Joint Cements, Resin Emulsions and Pigment Dispersions for

Non-Paint Use.

MASTER LABEL

Sub-label A: MWF Fluid, Material Preservative Use

Sub-label B: Drilling Additive Use

Sub-Label C: Fuel Additive Use

Sub-Label D: Bulk Container/Refutable Container Use

ACTIVE INGREDIENT: ..% WeightHexahydro-1,3,5-tris(2-hydroxyethyl)-s-triazine 78.5%INERT INGREDIENTS ....'. 21.5%TOTAL 100.0

EPA Reg. No. 365-76EPA Establishment Number 5383-XXX

DANGERSOLD FOR INDUSTRIAL USE

See Side Panel for Additional Precautionary StatementsKEEP OUT OF REACH OF CHILDREN

IN CASE OF EMERGENCY:%.*> CALL 1-800-424-9300" ** Troy Chemical Company, Ltd.

242 Applewood Crescent, Unit 14 f

* «

» «c F^l Concord, Ontario L4K4E5 Canada•*»•' ' c c « e c . 1-800-461-9364

Net Weight:

MADE IN CANADA* ec

* « t

cfto

Mergal 17411SUB-LABEL A

METALWORKING FLUIDS/MATERIAL PRESERVATIVE USE

« »** « f

' C C t C t C

. ' , ' J - J ' <* • • c « « « t c

c tt C t « £ «

t c

i <« e e i < t

* c c« - I. «•'* f

• o t c * cI t

c c < < t

MERGAL 17411A long lasting Broad Spectrum Bactericide, and Fungicide for the

Preservation of Adhesives, Metal Cutting Fluids and Coolants, JointCements, Resin Emulsions and Pigment Dispersions for Non-Paint Use.

ACTIVE INGREDIENT: % WeightHexahydro-1,3,5-tris(2-hydroxyethyl)-s-triazine 78,5%INERT INGREDIENTS .....21.5%TOTAL 100.0

• • • i

EPA Reg. No. 365-76EPA Establishment Number 5383-XXX

DANGER

SOLD FOR INDUSTRIAL USE

See Side Panel for Additional Precautionary Statements

KEEP OUT OF REACH OF CHILDREN

IN CASE OF EMERGENCY:CALL 1-800-424-9300

Troy Chemical Company, Ltd.242 Applewood Crescent, Unit 14

Concord, Ontario L4K 4E5 Canada1-800-461-9364

Net Weight:* e c r c. ti < «

C 1 C C< ct c

€c < c c c

MADE IN CANADA

e c

PRECAUTIONARY STATEMENTSHAZARDS TO HUMANS AND DOMESTIC ANIMALS

, DANGERCorrosive. Causes irreversible eye damage. Do not get in eyes or on clothing. Wear goggles or face ,shield. Wash thoroughly with soap and water after handling. Remove contaminated clothing and washclothing before reuse.

FIRST AID

IF IN EYES:

IF ON SKINOR .CLOTHING:

IFSWALLOWED:

IF INHALED:

Hold eye open and rinse slowly and gently with water for 15-20 minutes.Remove contact lenses, if present, after 5 minutes, then continue rinsing.Call a poison control center or doctor for treatment advice.

Take off contaminated clothing.Rinse skin immediately with plenty of water for 1 5-20 minutes.Call a poison control center or doctor for treatment advice.

Immediately call a poison control center or doctor. Do not inducevomiting unless told to do so by a poison control center or doctor. Do notgive any liquid to the person. Do not give anything by mouth to anunconscious person.Move person to fresh air.If person is not breathing call 911 or an ambulance, then give artificialrespiration preferably mouth-to-mouth if possible.Call a poison control center or doctor for further treatment advice.

Have the product container or label with you when calling a poison control center or doctor,or going for treatment. .

NOTE TO PHYSICIAN:Probable mucosal damage may contraindicate the use of gastric lavage.

ENVIRONMENTAL HAZARDSDo not dfetttsrge effluent containing this product into lakes, streams, ponds, estuaries, oceans orother wafeg| unless in accordance with the requirements of a National Pollutant DischargeEliminaticff .System (NPDES) permit and the permitting authority has been notified in writing prior todischarge.8 Do5 nqt«d«seharge effluent containing this product to sewer systems without previouslynotifying«fti©'Ideal §ewage treatment plant authority. For guidance contact your State Water Board orRegional office of '̂̂

c c «,c «C £

C- C 6 C C

.1 DIRECTIONS FOR USEIf is a violation of Federal Law to use this product in a manner inconsistent with its labeling.

« c ce « e

r • ; cv .. . v,..

SOLUBLE EMULSION, SYNTHETIC AND SEMI-SYNTHETIC CUTTING FLUIDS ANDCOOLANTS

Mergal 17411 should be used at a dilution of 0.15%.For best results, drain and clean the system before adding fresh cutting fluid. Add 0.15% ofMergal 17411 to the use dilution (1.2 pints per 100 gallons of diluted cutting fluid). 0.15% ofMergal 17411 should be added to the use dilution of the make-up fluid. To inhibit the growth ofbacteria and fungi in metalworking, cutting fluids, cooling, and lubricating fluids add Mergal17411 to the metalworking concentrate that will result in a 0.15% concentration. For exampleadd 3% Mergal 17411 to a metalworking fluid concentrate that will be diluted to 5% in water foruse.For all other uses (Adhesives, drilling additives, joint cements, pigment dispersions, asphaltemulsions and resin emulsions for non-residential use) use levels from 0.1-0.3% based on thetotal weight'of the formulation. Mergal 17411 should be added to the latter phase of themanufacturing process. It should not be exposed to temperatures exceeding 125°F (52 °C) forprolonged periods of time. Further it is not suitable for systems with a pH below 7. Mergal 17411may also be used to control microbial growth at the air-water interface of paint manufacturingraw material storage tanks. A 1.0% aqueous solution of Mergal 17411 may be sprayed over thesurface. Care should be taken to avoid removal of this interface in paint production. NOTE:May cause discoloration. Color stability in systems should be checked before use.

STORAGE AND DISPOSALDo not contaminate water, food, or feed by storage or disposal.

PESTICIDE STORAGE: Store in original container.PESTICIDE DISPOSAL: Wastes resulting from use of this product may be disposed of onsite or at an approved waste disposal facility.CONTAINER HANDLING: Nonrefillable container: Do not reuse or refill this container.

Triple rinse (or equivalent). Then offer for recycling or reconditioning, or puncture and dispoof in a sanitary landfill, or incineration, or, if allowed by state and local authorities, by burningIf burned, stay out of smoke.

I C C C C C

C 4 € « C «

e € « c ec

t c e « c

cMERGAL 17411SUB-LABEL B

DRILLING ADDITIVE USE

* «•«« * •

> • *

c «c-c

* *« c tc

t1

* < C 6 Cc

t t t c- *

r

• ' .. c ; , c -

MERGAL 17411\

A long lasting Broad Spectrum Bactericide, and Fungicide for DrillingAdditives

ACTIVE INGREDIENT: % WeightHexahydro-1,3,5-tris(2-hydroxyethyl)-s-triazine '. 78.5%INERT INGREDIENTS 21.5%TOTAL 100.0

. • \EPA Reg. No. 365-76EPA Establishment Number 5383-XXX

, DANGER

SOLD FOR INDUSTRIAL USE

See Side Panel for Additional Precautionary Statements

KEEP OUT OF REACH OF CHILDREN }

IN CASE OF EMERGENCY:CALL 1-800-424-9300

Troy Chemical Company, Ltd.242 Applewood Crescent, Unit 14Concord, Ontario L4K 4E5 Canada

1-800-461-9364

Net Weight:

< c c e c< rt * «

MADE IN CANADA

c C:

PRECAUTIONARY STATEMENTSHAZARDS TO HUMANS AND DOMESTIC ANIMALS

DANGERCorrosive. Causes irreversible eye damage. Do not get in eyes or on clothing. Wear goggles or faceshield. Wash thoroughly with soap and water after handling. Remove contaminated clothing andwash clothing before reuse.

FIRST AID

IF IN EYES:

IF ON SKINORCLOTHING:

IFSWALLOWED:

IF INHALED:

Hold eye open and rinse slowly and gently with water for 15-20 minutes.Remove contact lenses, if present, after 5 minutes, then continue rinsing.Call a poison control center or doctor for treatment advice.

Take off contaminated clothing.Rinse skin immediately with plenty of water for 1 5-20 minutes.Call a poison control center or doctor for treatment advice.

Immediately call a poison control center or doctor. Do not inducevomiting unless told to do so by a poison control center or doctor. Do notgive any liquid to the person. Do not give anything by mouth to anunconscious person.Move person to fresh air.If person is not breathing call 91 1 or an ambulance, then give artificialrespiration preferably mouth-to-mouth if possible.Call a poison control center or doctor for further treatment advice.

Have the product container or label with you when calling a poison control center or doctor,or going for treatment. ' . -

NOTE TO PHYSICIAN:Probable mucosal damage may contraindicate the use of gastric lavage.

ENVIRONMENTAL HAZARDSDo^not discharge effluent containing this product into lakes, streams, ponds, estuaries,ocQipg'or other waters unless in accordance with the requirements of a National PollutantDischarge Elimination System (NPDES) permit and the permitting authority has been notifiedin'writing prior to discharge. Do not discharge effluent containing this product to sewersystems without: previously notifying the local sewage treatment plant authority. For

' . . coftta.cf your State Water Board o r Regional office o f t h e EPA.

c <« : * . DIRECTIONS FOR USEtcis, a.'violation of Federal Law to use this product in a manner inconsistent with its labeling.

c c< c Oilfield Systems

C . C .lQ

For controlling aerobic slime-forming bacteria (Pseudomonas sp.) or iron-oxidizingbacteria (Gallionella sp.) and anaerobic sulfate-reducing bacteria (Desulfovibriodesulfuricans) in oilfield water systems,such as subsurface injection water, add 5-150ppm Mergal 17411 depending on the severity of the contamination. Additions should bemade with a metering pump at the free water knockouts before or after the injectionpumps and injection well headers.

Continuous-fee method: If this system is noticeably fouled, add 20-150 ppm Mergal17411 (1.7-12.8 gal per 2000 barrels of water^ continuously untilthe desired degree ofcontrol is achieved. Subsequently, treat with 5-150 ppm Mergal 17411 (0.43-12.8 gal.per 2000 barrels of water) continuously as needed for control.

1 v i, • .

Intermittent or slug method: If the system is noticeably fouled or to maintain control ofthe system, add 20-150 ppm Mergal 174II (1.7-12.8 gal. per 2000 barrels of water)intermittently for 2-8 hours per day on from 1-4 days per week, depending on theseverity of the contamination.

Preserving Drilling Muds and Workover and Completion FluidsDetermine the volume of Mergal 17411 necessary to provide a concentration of 500-1000ppm by weight of Mergal 17411 in the drilling mud system, workover and completionfluid. For example, 21-42 gallons of Mergal 17411 per each 1000 barrels of drilling mudprovides this concentration. As the system circulates, add Mergal 17411 in a thin stream.Add additional Mergal 17411 to the system to maintain the proper concentration as thetotal volume of the system increases.

NOTE: May cause discoloration. Color stability in systems should be checked before use.

STORAGE AND DISPOSALDo not contaminate water, food, or feed by storage or disposal.PESTICIDE STORAGE: Store in original container.PESTICIDE DISPOSAL: Wastes resulting from use of this product may be disposed ofon site or at an approved waste disposal facility.CONTAINER HANDLING: Nonrefillable container: Do not reuse or refill this container.

Triple rinse (or equivalent). Then offer for recycling or reconditioning, or puncture anddispose of in a sanitary landfill, or incineration, or, if allowed by state and localauttigrlties, by burning. If burned, stay out of smoke. .

r * « cc 4

« « * « * ic cI «: ,

e e « c mc

c c t c- c

c c

MERGAL 17411SUB-LABEL C

FUEL ADDITIVE USE

« c « t » e< c

e c

c * c « e« <

e c c «- c

C . C ' "•W)

MERGAL 17411A long lasting Broad Spectrum Bactericide, and Fungicide for Fuel

Additives

ACTIVE INGREDIENT: % WeightHexahydro-1,3,5-tris(2-hydroxyethyl)-s-triazine ..78.5%INERT INGREDIENTS .......21.5%TOTAL 100.0

EPA Reg. No. 365-76EPA Establishment Number 5383-XXX

DANGER

SOLD FOR INDUSTRIAL USE

See Side Panel for Additional Precautionary Statements

KEEP OUT OF REACH OF CHILDREN

IN CASE OF EMERGENCY:CALL 1-800-424-9300

Troy Chemical Company, Ltd.242 Applewood Crescent, Unit 14

Concord, Ontario L4K 4E5 Canada1-800-461-9364

* e &> « »c «*

• < * « C < C*'• « t

* * « C «

« * ft

' * « « » € • « «

. .t« \t'C t

' " C 6 « « *t <

* I C C I, «

Net Weight:

MADE IN CANADA

c c

PRECAUTIONARY STATEMENTSHAZARDS TO HUMANS AND DOMESTIC ANIMALS

DANGER iCorrosive. Causes irreversible eye damage. Do not get in eyes or on clothing. Wear goggles orface shield. Wash thoroughly with soap and water after handling. Remove contaminated clothing"and wash clothing before reuse.

FIRST AID

IF IN EYES:

IF ON SKINORCLOTHING:

/IFSWALLOWED:

IF INHALED:

Hold eye open and rinse slowly and gently with water for 1 5-minutes. Remove contact lenses, if present, after 5 minutescontinue rinsing.Call a poison control center or doctor for treatment advice.

/ .

Take off contaminated clothing.Rinse skin immediately with plenty of water for 15-20 minuteCall a poison control center or doctor for treatment advice.

20then

s.

Immediately call a poison control center or doctor. Do not inducevomiting unless told to do so by a poison control center or doctor. Donot give any liquid to the person. Do not give anything by mouth to anunconscious person.Move person to fresh air.If person is not breathing call 91 1 or an ambulance, then giverespiration preferably mouth-to-mouth if possible.Call a poison control center or doctor for further treatment ac

Have the product container or label with you when calling a poison control centdoctor, or going for treatment.

NOTE TO PHYSICIAN:

j artificial

vice.sror

Probable mucosal damage may contraindicate the use of gastric lavage.

(. .. ENVIRONMENTAL HAZARDSDo «n©t 'discharge effluent containing this product into lakes, streams, ponds, estuaries,oceShs or cstrieff waters unless in accordance with the requirements of a NationalPcljuta^t Difgha/cje Elimination System (NPDES) permit and the permitting authorityhas been notified in writing prior to discharge. Do not discharge effluent containing thisproduct to spwsF-systems without previously notifying the local sewage treatment plantauthority. FofjJGfdance contact your State Water Board or Regional office of th|e EPA

DIRECTIONS FOR USE

c C:70

It is a violation of Federal Law to use this product in a manner inconsistent with itslabeling.

BACTERIAL CONTROL ASSOCIATED WITH FREE AND DISPERSED WATERCOMMONLY FOUND IN FUEL SYSTEMS:

Add this product to fuel tanks to control microbial growth in diesel oil, fuel oil, gasoline orkerosene fuel systems. Treatment may be achieved by slug dosing or intermittentmetering to provide the proper concentration of this product.

• • • - ' - ' - '• !If the volume of water is known, add 0.5-1.5 gallons of this product to each 1,000gallons of water to achieve concentrations of 500-1000 ppm in the water phases If thevolume of water is unknown add 20 ounces-1 gallon of this product to each 10^0gallons of fuel to achieve concentrations ranging between 150-1000 ppm.

Concentrations of 150-500 ppm of Mergal 17411 are appropriate for preventivetreatment. ^

Concentrations of 1000-1500 ppm are appropriate for curative treatment. Sincemicrobes tend to grow within biofilm communities, two or more curative treatmentsintroduced at one-two day intervals may be required to treat heavily contaminated fueltanks successfully. Since this product is not particularly hydrocarbon soluble there isno adverse effect if some excess accumulates in tank bottoms. It will function as acorrosion inhibitor at higher concentrations.

STORAGE AND DISPOSALDo not contaminate water, food, or feed by storage or disposal.PESTICIDE STORAGE: Store in original container.PESTICIDE DISPOSAL: Wastes resulting from use of this product may be disposed ofon site or at an approved waste disposal facility.CONTAINER HANDLING: Nonrefillable container: Do not reuse or refill this container.

Triple rinse (or equivalent). Then offer for recycling or reconditioning, or puncture anddispose of in a sanitary landfill, or incineration, or, if allowed by state and local !authorities, by burning. If burned, stay out of smoke.

c *« c

C C C C 4 CC c

C 4

t « « t CC C

c c c c c

c c

MERGAL 17411SUB-LABEL D

METALWORKING FLUIDS/MATERIAL PRESERVATIVE USEBulk/Refillable Container Use

(40-45,000 Ib. semi-containers)

• • * •* <*.• • *

* « *' * «

« s «

c tc c

« r c« C

« C C t C €

c cc c

t C C € C

* ce i c c c

c.

MERGAL 17411A long lasting Broad Spectrum Bactericide, and Fungicide for the -

Preservation of Adhesives, Metal Cutting Fluids and Coolants, JointCements, Resin Emulsions and Pigment Dispersions for Non-Paint Use.

ACTIVE INGREDIENT: % WeightHexahydro-1,3,5-tris(2-hydroxyethyl)-s-triazine 78.5%INERT INGREDIENTS .21.5%TOTAL 100.0

EPA Reg. No. 365-76EPA Establishment Number 5383-XXX

DANGER

SOLD FOR INDUSTRIAL USE

See Side Panel for Additional Precautionary Statements

KEEP OUT OF REACH OF CHILDREN

IN CASE OF EMERGENCY:CALL 1-800-424-9300

Troy Chemical Company, Ltd.242 Applewood Crescent, Unit 14

Concord, Ontario L4K 4E5 Canada1-800-461-9364

• •• •* <• •«•Net Weight:

*'*

* * c e c c. cc

C I

e c € t et

e c- c c c

MADE IN CANADA

r

PRECAUTIONARY STATEMENTSHAZARDS TO HUMANS AND DOMESTIC ANIMALS

DANGERCorrosive. Causes irreversible eye damage. Do not get in eyes or on clothing. Wear goggles orface shield. Wash thoroughly with soap and water after handling. Remove contaminatedclothing and wash clothing before reuse.

FIRST AID

IF IN EYES:

IF ON SKINORCLOTHING:

IFSWALLOWED:

IF INHALED:

Hold eye open and rinse slowly and gently with water for 1 5-2minutes. Remove contact lenses, if present, after 5 minutesjcontinue rinsing.Call a poison control center or doctor for treatment advice.

Take off contaminated clothing.Rinse skin immediately with plenty of water for 15-20 minute;Call a poison control center or doctor for treatment advice.

/

Immediately call a poison control center or doctor. Do not incvomiting unless told to do so by a poison control center or donot give any liquid to the person. Do not give anything by meunconscious person.Move person to fresh air.If person is not breathing call 91 1 or an ambulance, then giverespiration preferably mouth-to-mouth if possible.Call a poison control center or doctor for further treatment ad

Have the product container or label with you when calling a poison control centedoctor, or going for treatment.

NOTE TO PHYSICIAN:

>0then

lucector. Douth to an

artificial

nee.jror

Probable mucosal damage may contraindicate the use of gastric lavage.

ENVIRONMENTAL HAZARDSDo.fiot'discharge effluent containing this product into lakes, streams, ponds, estuaries,ocegng'or other waters unless in accordance with the requirements of a National PollutantDisbrfasge Elimination System (NPDES) permit and the permitting authority (has beennotified in wrpR§«|rior to discharge. Do not discharge effluent containing this product tosewfer.s^sterfis without previously notifying the local sewage treatment plant authority.For. cfujd£nce»cpfiltact your State Water Board or Regional office of the EPA.

c c c c tr c

c c c c t

:...j • DIRECTIONS FOR USEIt is^a violation of Federal Law to use this product in a manner inconsistent with its*c

c" labeling.

r GZO

SOLUBLE EMULSION, SYNTHETIC AND SEMI-SYNTHETIC CUTTING FLUIDS ANDCOOLANTS

Mergal 17411 should be used at a dilution of 0.15%. ^For best results, drain and clean the system before adding fresh cutting fluid. Add0.15% of Mergal 174II to the use dilution (1.2 pints per 100 gallons of diluted cuttingfluid). 0.15% of Mergal 17411 should be added to the use dilution of the make-up fluid.To inhibit the growth of bacteria and fungi in metalworking, cutting fluids, cooling, andlubricating fluids add Mergal 17411 to the metalworking concentrate that will result in a0.15% concentration. For example add 3% Mergal 17411 to a metalworking fluidconcentrate that will be diluted to 5% in water for use.

i

For all other uses (Adhesives, drilling additives, joint cements, pigment dispersions,asphalt emulsions and resin emulsions for non-residential use) use levels from 0.1-0.3%based on the total weight of the formulation. Mergal 17411 should be added to the latterphase of the manufacturing process. It should not be exposed to temperaturesexceeding 125°F (52 °C) for prolonged periods of time. Further it is not suitable forsystems with a pH below 7. Mergal174ll may also be used to control microbial growth atthe air-water interface of paint manufacturing raw material storage tanks. A 1.0%aqueous solution of Mergal 174JI may be sprayed over the surface. Care should betaken to avoid removal of this interface in paint production. NOTE: May cause idiscoloration. Color stability in systems should be checked before use.

STORAGE AND DISPOSALDo not contaminate water, food, or feed by storage or disposal.

PESTICIDE STORAGE: Store in original container.PESTICIDE DISPOSAL: Wastes resulting from use of this product may be disposed ofon site or at an approved waste disposal facility.Container handling instructions are not required for transport vehicles."CONTAINER HANDLING (for the end users' bulk tanks): Refillable container. Refillwith pesticide only. Do not reuse this container for any other purpose. Cleaning thecontainer before final disposal is the responsibility of the person disposing of thecontainer. Cleaning before refilling is the responsibility of the refiller. Use standardindygj[y practices for cleaning bulk containers or contact the registrant for more

C C CC C. I

* c «

< c& €>

e c c c cc

c c

c t c c cf

t- c t e c