EP-DCX101v3 Control Builder

8/12/2019 EP-DCX101v3 Control Builder

1/613

Experion PKS

Control Builder

Reference

Doc. No.: EP-DCX101

Release: 100Last Revision Date: 1/03

Volume 3 of 3


2/613

ii Experion PKSControl Builder Reference Release 100Honeywell 1/03

Notices and Trademarks

Copyright 2003 by Honeywell, Inc.Release 100 January 2003

While this information is presented in good faith and believed to be accurate, Honeywell disclaimsthe implied warranties of merchantability and fitness for a particular purpose and makes noexpress warranties except as may be stated in its written agreement with and for its customers.

In no event is Honeywell liable to anyone for any indirect, special or consequential damages. Theinformation and specifications in this document are subject to change without notice.

Honeywell, and TotalPlantare U.S. registered trademarks.

Other brand or product names are trademarks of their respective owners.

Honeywell Inc.

ACS Industry Solutions

2500 West Union Hills Dr.

Phoenix, AZ 85027

800-343-0228


3/613

Release 100 Experion PKSControl Builder Reference iii1/03 Honeywell

About This Document

Contacts

Wide Web

The following lists Honeywells World Wide Web sites that will be of interest to our

industrial automation and control customers.

Honeywell Organization WWW Address (URL)

Corporate http://www.honeywell.com

ACS Industry Solutions http://www.acs.honeywell.com

Telephone

Contact us by telephone at the numbers listed below.

Organization Phone Number

United Statesand Canada

HoneywellACS - IndustrySolutions

1-800-343-0228 Solution Support Center1-800-525-7439 On-Site Service Information1-800-852-3211 Training Registrar

Experion PKS Support Program Information:1-800-288-7491

Asia Pacific Honeywell Asia PacificHong Kong

(852) 28298298

Pacific Honeywell LimitedAustralia

(612) 9353 7000

Korea HoneywellSeoul, Korea

82-2-799-6318

China HoneywellChina

86-10-65610371

Europe Honeywell PACEBrussels, Belgium

[32-2] 728-2111

Latin America HoneywellSunrise, Florida U.S.A.

(954) 845-2600


4/613

About This Document

iv Experion PKSControl Builder Reference Release 100Honeywell 1/03


5/613

About This Document

Release 100 Experion PKSControl Builder Reference v1/03 Honeywell

Symbol definitions

The following table lists those symbols used in this document to denote certain

conditions.

Symbol Definition

ATTENTION

Used to identify information that requires special consideration.

TIP

Used to identify information that can not be classified as requiring

special consideration, but as "nice-to-know."

REFERENCE - INTERNAL

Used to identify an information reference source internal to thedocument set.

REFERENCE - EXTERNAL

Used to identify an information reference source external to thedocument set.

CAUTION

Refers to the Product Manual for additional information.

WARNING

Refers the to the Product Manual for additional information.

SHOCK HAZARD

WARNING: risk of electrical shock. This symbol warns the user of apotential shock hazard where HAZARDOUS LIVE voltages greaterthan 30 Vrms, 42.4 Vpeak, or 60 VDC may be accessible.

ESD HAZARD

Electrostatic Discharge (ESD) hazards. Observe precautions forhandling electrostatic sensitive devices

Protective Earth (PE) terminal. Provided for connection of theprotective earth (green or green/yellow) supply system conductor.


6/613

vi Experion PKSControl Builder Reference Release 100Honeywell 1/03

Symbol Definition

Functional earth terminal. Used for non-safety purposes such asnoise immunity improvement. NOTE: This connection shall bebonded to protective earth at the source of supply in accordancewith national local electrical code requirements.

Earth Ground. Functional earth connection. NOTE: This connectionshall be bonded to Protectiveearth at the source of supply inaccordance with national and local electrical code requirements.

Chassis Ground. Identifies a connection to the chassis or frame ofthe equipment shall be bonded to Protective Earth at the source ofsupply in accordance with national and local electrical coderequirements.


7/613

Release 100 Experion PKSControl Builder Reference vii1/03 Honeywell

Contents

Part II Control Builder Parameter Reference0xxxx to Zxxxx Parameters and Appendices

OxxxxParameters............................................................................... 653

PxxxxParameters............................................................................... 757

QxxxxParameters............................................................................... 913

RxxxxParameters............................................................................... 915

SxxxxParameters............................................................................. 1005

TxxxxParameters ............................................................................. 1163

UxxxxParameters............................................................................. 1197

VxxxxParameters............................................................................. 1209

WxxxxParameters............................................................................ 1215

XxxxxParameters............................................................................. 1225

Yxxxx

Parameters............................................................................. 1241

ZxxxxParameters ............................................................................. 1243


8/613

Contents

viii Experion PKSControl Builder Reference Release 100Honeywell 1/03

Display Elements Appendix...............................................................1245


9/613

Release 100 Experion PKSControl Builder Reference ix1/03 Honeywell

Tables

Part II Control Builder Parameter ReferenceOxxxx to Zxxxx Parameters and AppendicesTable 5 PV Characterization Range for IOP Types HLAI, LLAI, LLMUX, and RHMUX837Table 6 PV Characterization Range for IOP Type STI ST3000 Pressure Transmitters

and MagneW 3000 Flowmeters............................................................................839Table 7 PV Characterization Range for IOP Type STI STT3000 Temperature

Transmitters (SENSRTYP = STT) ........................................................................840Table 8 Extended Range Parameter Defaults when SENSRTYP equals THERMCPL and

PVTEMP equals degrees C..................................................................................849Table 9 Extended Range Parameter Defaults when SENSRTYP equals RTD and

PVTEMP equals degrees C..................................................................................850Table 10 URL Settings for Smart Pressure Transmitters SENSRTYP SPT_DP,

SPT_GP, and SPT_AP.......................................................................................1204Table 11 URL Settings for Smart Temperature Transmitters SENSRTYP STT.... 1204Table 12 URL Settings for Magnetic Flowmeter Transmitter SENSRTYP SFM....1205


10/613

Tables

x Experion PKSControl Builder Reference Release 100Honeywell 1/03


11/613

Part II

Control Builder ParameterReference (Nxxxx to Zxxxx Parameters)


12/613


13/613

Release 100 Experion PKSControl Builder Reference 6531/03 Honeywell Part II

OxxxxParameters

OFFNRMALM.FL

Specific to Block(s) Flag, Push.

Description Off Normal Alarm Flag

Data Type Boolean

Range Off (0)On (1)

Default Off (0)

Config Load No

Access Lock View Only

Residence CEE

Related Parameters NORMAL,OFFNRMALM.PR,OFFNRMALM.SV,PV.

Remarks When On, it indicates that the Flag function block is notcurrently in the normal state.

Specific to Block(s) DevCtl

Description Off Normal Alarm Flag - Indicates the OFF-Normalcondition. The Device is OFF-Normal wherever the ProcessVariable (PV) does not equal OPREQ.

Data Type Boolean

Range Off (0)On (1)

Default Off (0)

Config Load No


Residence CEE


14/613

Oxxxx ParametersOFFNRMALM.PR

654 Experion PKSControl Builder Reference Release 100Part II Honeywell 1/03

Related Parameters BYPASS,CMDDISALM.FL,CMDDISALM.PR,CMDDISALM.SV,CMDDISALM.TM[0..2],GOPREQ,GPV,HIALM,OPREQ,PV.

Remarks InActive when GOPREQ is Null.

OFFNRMALM.PR

Specific to Block(s) Flag, Push.

Description Off Normal Alarm Priority

Data Type Enumeration ALMPR

Range None (0)Journal (1)Low (2)High (3)Urgent (4)

Default Low (2)

Config Load Yes

Access Lock Engineer

Residence CEE

Related Parameters OFFNRMALM.FL,OFFNRMALM.SV.

Remarks


Description Off Normal Alarm Priority

Data Type Enumeration ALPRIOR


15/613

Oxxxx ParametersOFFNRMALM.SV



Default None (0)

Config Load Yes


Residence CEE

Related Parameters GOPREQ,OPREQ.

Remarks InActive when GOPREQ is Null.

OFFNRMALM.SV

Specific to Block(s) DevCtl, Flag, Push.

Description Off Normal Alarm Severity

Data Type Integer

Range 0 to 15

Default 0

Config Load Yes


Residence CEE

Related Parameters OFFNRMALM.FL,OFFNRMALM.PR.

DevCtl Only:GOPREQ,OPREQ.

Remarks DevCtl only: InActive when GOPREQ is Null.


16/613

Oxxxx ParametersOFFNRMFL


OFFNRMFL

Specific to Block(s) DICHANNEL (PMIO)

Description Off-Normal Alarm Flag. Shows whether an off-normalalarm has been detected at this point or not.

Data Type Boolean

Range Off: No alarm exists.

On: Current PV state is not the same as the configured

PVNORMAL state.

Default Off

Config Load No


Residence IOP

Related Parameters

Remarks This parameter is only exposed if ALMOPT is OFFNORML.

OFFPULSE

Specific to Block(s) DOCHANNEL (PMIO)

Description Off Pulse Command. Lets users specify how long a statusoutput (SO) is to be set to Off in seconds. At the end of theOFFPULSE time, SO is set to On.

Data Type 64-Bit Real Number

Range 0.0 TO 60.0 seconds

Default N/A

Config Load No

Access Lock Operator

Residence IOP


17/613

Oxxxx ParametersOHMOFFSET


Related Parameters

Remarks An OFFPULSE setting of 0.0, immediately sets the SO toOn.

This parameter exists in the I/O Processor (IOP) as a 32-bitfloating point value, however it is converted into a 64-bitfloating-point value for convenience when wiring to otherblock parameters in Control Builder (CB).

OHMOFFSET

Specific to Block(s) AIC

Description 10-Ohm Offset - Corrective value for use only with 10-ohmcopper RTD.

Data Type 32-Bit Integer

Range -99 to 99

Default 0

Config Load No


Residence CEE

Related Parameters CALBIAS,SENSORTYPE[0..numChans-1].

Remarks OHMOFFSET can only be configured on the RTD inputmodule, and is only configurable when SENSORTYPE is setequal to 10_Cop_427.


18/613

Oxxxx ParametersOHMOFFSET[0..numChans-1]


OHMOFFSET[0..numChans-1]

Specific to Block(s) AIM

Description 10-Ohm Offset - Corrective value for use only with 10-ohmcopper RTD.


Range -99 to 99

Default 0

Config Load Yes

Access Lock Application Developer

Residence CEE

Related Parameters CALBIAS[0..numChans-1],SENSORTYPE[0..numChans-1].

Remarks OHMOFFSET can only be configured on the RTD inputmodule.

OI[0..2]Specific to Block(s) DevCtl

Description Override Interlock

Data Type Boolean

Range Off (0)On (1)

Default Off (0)

Config Load No

Access Lock Engineer/ Other Function Block (see Remarks)

Residence CEE


19/613

Oxxxx ParametersOI[0..2]


Related Parameters BYPASS,BYPPERM,GOP,NUMDOUTS,OIALM.FL[0..2],OIALM.OPT[0..2],OIALM.PR[0..2],

OIALM.SV[0..2],OP,SAFEOP,SI,SIALM.FL,SIALM.OPT,SIALM.PR,SIALM.SV.

Remarks Engineer can change only if function block is inactive.

OI(x) is illegal if NUMDOUTS is less-than x.

These interlocks are not active is BYPASS is set On.

The priority of the OI interlocks is determined by SAFEOP.

If SAFEOP = S0, then priority is SI, 0, 1, 2. If SAFEOP = S1, then priority is SI, 1, 0, 2. If SAFEOP = S2, then priority is SI, 2, 0, 1.


20/613

Oxxxx ParametersOIALM.FL[0..2]


OIALM.FL[0..2]


Description Override Interlock Alarm Flag

Data Type Boolean

Range Off (0)On (1)

Default Off (0)

Config Load No


Residence CEE

Related Parameters BYPASS,BYPPERM,HIALMINALM,NUMDOUTS,OIALM.FL[0..2],OIALM.PR[0..2],OIALM.SV[0..2].

Remarks Always Off, if BYPASS is set On.

OIALM.OPT[0..2]


Description Override Interlock Alarm Option.

Data Type Enumeration OVRDALOP

Range No (0)Yes (1)

Default N/A

Config Load Yes



21/613

Oxxxx ParametersOIALM.PR[0..2]


Residence CEE

Related Parameters NUMDOUTS

Remarks Illegal if NUMDOUTS = 0.

OIALM.PR[0..2]


Description Override Interlock Alarm Priority



Default Low (2)

Config Load Yes


Residence CEE

Related Parameters NUMDOUTS,OI[0..2],OIALM.FL[0..2],OIALM.OPT[0..2],OIALM.SV[0..2].



22/613

Oxxxx ParametersOIALM.SV[0..2]


OIALM.SV[0..2]


Description Override Interlock Alarm Severity


Range 0 to 255

Default 0

Config Load Yes


Residence CEE

Related Parameters NUMDOUTS,OI[0..2],OIALM.FL[0..2],OIALM.OPT[0..2],OIALM.PR[0..2].


OLDAV

Specific to Block(s) Totalizer, Pulse Input Totalizer

Description Old Accumulated Value - The value of the Process Variable(PV), just before it was reset. This parameter makes the oldvalue available to those functions that need it.


Range Greater-than or equal-to 0.0

Default N/A

Config Load No


Residence CEE


23/613

Oxxxx ParametersONPULSE


Related Parameters PV

Remarks

ONPULSE


Description On Pulse Command. Lets users specify how long a statusoutput (SO) is to be set to On in seconds. At the end of theONPULSE time, SO is set to Off.


Range 0.0 TO 60.0 seconds

Default N/A

Config Load No


Residence IOP

Related Parameters

Remarks An ONPULSE configuration of 0.0, immediately sets the

SO to Off.

This parameter exists in the I/O Processor (IOP) as a 32-bitfloating point value, however it is converted into a 64-bitfloating point value for convenience when wiring to otherblock parameters in Control Builder (CB).


24/613

Oxxxx ParametersOP


OP

Specific to Block(s) All RegCtl Blocks except Fanout: PID, RemCas, RatioBias,RegCalc, Switch, AutoMan, OvrdSel, and RampSoak.

Description Output Value (in Percent)


Range OPEXLOLM to OPEXHILM

Default 0.0

Config Load No


Residence CEE

Related Parameters OPEU

Remarks Output Value (OP) is represented in percentage of theCalculated Value (CV) range (CVEULOCVEULO andCVEUHI).


Description Commanded Output State

Data Type String

Range Length: 12 characters

Default STATETEXT[4]

Config Load No


Residence CEE


25/613

Oxxxx ParametersOP


Related Parameters BYPASS,CMDDISALM.FL,CMDDISALM.PR,CMDDISALM.SV,CMDDISALM.TM[0..2],CMDFALALM.FL,CMDFALALM.PR,CMDFALALM.SV,CMDFALALM.TM[0..2],GOP,GOPFINAL,GOPREQ,MOMSTATE,

NUMDOUTS,NUMSTATES,OI[0..2].OPDOMAP[0..3][1..3],OPFINAL,OPREQ,SAFEOP,SAFEREDTAG,SI,STATETEXT[0..6],UNCMDALM.FL,UNCMDALM.PR,UNCMDALM.SV.

Remarks OP is a String set equal to STATETEXT[GOP].

Access is illegal, if NUMDOUTS = 0.

STATETEXT[6] [State2] is illegal if NUMSTATES = 2.

STATETEXT[2] [Active] is illegal if SAFEOP = S2.

Specific to Block(s) PWM Channel

Description Output Value in percent

Data Type Real Number

Range N/A

Default 0

Config Load No


Residence CEE

Related Parameters

Remarks

Specific to Block(s) AOCHANNEL (PMIO)

Description Output. Defines the output value from this point in percent.



26/613

Oxxxx ParametersOP


Range -6.9 to 106.9 percent

Default -6.9 percent of Full Scale

Config Load No


Residence IOP

Related Parameters

Remarks The control mode must be Manual before an operator canadjust the OP manually.


Description PWM Output. Specifies the percent on-time for a DOTYPEPWM output. (For DOTYPE STATUS output, use SO.)


Range 0.0 to 100.0 percent

Default 0.0 percent

Config Load No


Residence IOP

Related Parameters PERIOD

Remarks Pulse on-time is calculated as follows.

For DIRECT action:

Pulse On-Time = (OP percent x PERIOD) / 100

For REVERSE action:

Pulse On-Time = (100 percent - OP percent x PERIOD) /100


27/613

Oxxxx ParametersOP[1..8]


OP[1..8]

Specific to Block(s) Fanout

Description Output (OP) Values (in percent) for function blocks withMultiple Outputs - There is one value per output.



Default OPEXLOLM

Config Load No


Residence CEE

Related Parameters OPEU[1..8]

Remarks OP is represented in percentage of the Calculated Variable(CV) range (CVEULO and CVEUHI).

OP[1..NUMCHAN]

Specific to Block(s) AO8, AO16

Description Target Output Value




Config Load No


Residence IOP

Related Parameters

Remarks The control mode must be Manual before an operator canadjust the OP manually.


28/613

Oxxxx ParametersOP[1..16].CONFIGCODE


OP[1..16].CONFIGCODE

Specific to Block(s) Step

Description Output Configuration Code

Data Type Enumeration CSCOCONFIGCODEOUTPUT

Range None (0)Ok (1)UnknownError (2)ImplicitConv (3)LossOfPrecsn (4)

UnexpctEnd (5)UnexpctComma (6)ColonWoQMark (7)FctNotMltArg (8)ClosParenExp (9)OperandExp (10)MissingArg (11)OperatorExp (12)ColonExp (13)TypeMismatch (14)TypeNotSupp (15)SyntaxError (16)ExprTooCmplx (17)NotEPcodeMe (18)NotEDataStak (19)

UnsuppFeatur (20)ExprTooLong (21)DivideByZero (22)UnknownToken (23)UnexpTokenOS (24)UnknownFunc (25)UnexpOCExpr2 (26)UnexpOCExpr3 (27)ZeroArgument (28)UnexpToken (29)InvalResult (30)InvalTokenTb (31)IntegerExp (32)DoubleExp (33)MissedImpl (34)

UnicodeConv (35)ConsstExprRem (36)DuplExprRem (37)DstnInvalid (38)DstnCRqInval (39)


29/613

Oxxxx ParametersOP[1..16].CONFIGCODE


ExtUse40 (40)ExtUse41 (41)ExtUse42 (42)ExtUse43 (43)ExtUse44 (44)ExtUse45 (45)ExtUse46 (46)ExtUse47 (47)ExtUse48 (48)ExtUse49 (49)ExtUse50 (50)UnsupConTyp (51)UnExpClsParn (52)

CantAssRVal (53)UnExpArrOpen (54)ArrClsExpect (55)ArrOpnExpect (56)ArrIndxError (57)StringExpect (58)InvalidRefer (59)TooManyConnS (60)CantConvInpt (61)

Default None (0)

Config Load No


Residence CEE

Related Parameters

Remarks See OP[1..16].CONFIGSTS for additional information.


30/613

Oxxxx ParametersOP[1..16].CONFIGDESC


OP[1..16].CONFIGDESC


Description Output Configuration Descriptor

Data Type String

Range Maximum of 39 characters.

Default Null String

Config Load No


Residence CEE

Related Parameters

Remarks See OP[1..16].CONFIGSTS for additional information.

OP[1..16].CONFIGSTS


Description Output Configuration Status

Data Type Enumeration CSCOCONFIGSTS

Range Ok (0)Information (1)Warning (2)SevereWarn (3)Fail (4)Error (5)SevereError (6)

Default Ok (0)

Config Load No


Residence CEE


31/613

Oxxxx ParametersOP[1..16].DESC


Related Parameters OP[1..16].CONFIGCODE,OP[1..16].CONFIGDESC.

Remarks Step output configuration status parametersOP[1..16].CONFIGSTS, OP[1..16].CONFIGCODE,OP[1..16].CONFIGDESC are set on SCM STATE transitionfrom Inactive to Validated.

OP[1..16].DESC


Description Output Description

Data Type String

Range Maximum Length: 64 characters

Default Null String

Config Load Yes


Residence SR

Related Parameters

Remarks


32/613

Oxxxx ParametersOP[ ].DSTN


OP[ ].DSTN


Description This is an internal parameter for system use only.

Data Type

Range

Default

Config Load

Access Lock

Residence

Related Parameters

Remarks

OP[1..16].DSTNCTRLREQ


Description Output Destination Control Request Connector

Data Type Output Connector

Range N/A

Default N/A

Config Load No


Residence CEE

Related Parameters CONTROLREQ


33/613

Oxxxx ParametersOP[1..16].EXECCODE


Remarks Step outputs that store to DevCtl or RegCtl function blocksconfigured as Level 1 Device Drivers must make aCONTROLREQ to the function block. OP[i] is configured tomake a CONTROLREQ by exposing the block pinOP[i].DSTNCTRLREQ on the step, and connecting it(through a parameter connector) to the function blocksCONTROLREQ parameter.

OP[1..16].EXECCODE


Description Output Execution Code

Data Type Enumeration CSCOEXECCODE

Range None (0)ConfigError (1)ExprEvalFail (2)StoreFailed (3)CommError (4)StoreWarning (5)InternalErr (6)CtrlReqErr (7)DataTypeErr (8)StorePending (9)

Default None (0)

Config Load No


Residence CEE

Related Parameters

Remarks See OP[1..16].EXECSTS for additional information.


34/613

Oxxxx ParametersOP[1..16].EXECDESC


OP[1..16].EXECDESC


Description Output Execution Code Descriptor

Data Type String

Range Maximum of 39 characters.

Default Null String

Config Load No


Residence CEE

Related Parameters

Remarks See OP[1..16].EXECSTS for additional information.

OP[1..16].EXECSTS


Description Output Execution Status

Data Type Enumeration CSCOEXECST

Range Ok (0)Bypass (1)Info (2)Warning (3)Fail (4)Error (5)OkPaused (6)BypassPaused (7)InfoPaused (8)WarnPaused (9)FailPaused (10)ErrorPaused (11)

Default Ok (0)


35/613

Oxxxx ParametersOP[1..16].EXPRPCODE


Config Load No


Residence CEE

Related Parameters OP[1..16].EXECCODE,OP[1..16].EXECDESC.

Remarks Step output execution status parametersOP[1..16].EXECSTS, OP[1..16].EXECCODE, andOP[1..16].EXECDESC are updated when the step is in theSCMs current scope of execution.

OP[1..16].EXPRPCODE



Data Type

Range

Default

Config Load

Access Lock

Residence

Related Parameters

Remarks


36/613

Oxxxx ParametersOP[1..16].SRCEXPR


OP[1..16].SRCEXPR


Description Output Source Expression

Data Type String

Range Maximum Length: 255 characters

Default Null String

Config Load Yes


Residence SR

Related Parameters

Remarks

OP[1..16].STATE


Description Sequential Control Module (SCM) Step Output State

Data Type Enumeration CSCOPARTSTATE

Range Edit (0)Inactive (1)Disabled (2)Enabled (3)

Active (4)ActiveComplt (5)ProcOutputs (6)ProcMessages (7)ProcMinWait (8)

Default Edit (0)

Config Load No



37/613

Oxxxx ParametersOP[1..16].TYPE


Residence CEE

Related Parameters

Remarks

OP[1..16].TYPE


Description Output Type

Data Type Enumeration CSCOOPTYPE

Range Null (0)Set (1)NotStored (2)

Default Null (0)

Config Load Yes


Residence CEE

Related Parameters CONTROLREQ,

MODEREQ,OPREQ,SCMOPT,SPRATEREQ,SPREQ,SPTVREQ.

Remarks Null output type is valid only if ControlModule.SCMOPT =None. If ControlModule.SCMOPT = Fixed, then ControlRequests (CONTROLREQ) to the RegCtl function block mustuse a set output type, output requests to the DevCtl functionblock, and use a set of NotStored output type.


38/613

Oxxxx ParametersOPBIAS


OPBIAS

Specific to Block(s) All RegCtl Blocks except Fanout: AutoMan, OvrdSel, PID,PIDFF, PosProp, PulseCount, PulseLength, RampSoak,RemCas, RatioBias, RegCalc, and Switch.

Description Total Output Bias (in Engineering Units) OPBIAS is the sumof two components: a user-specified fixed bias (OPBIAS.FIX)and a calculated floating bias (OPBIAS.FLOAT).


Range N/A

Default N/A

Config Load No


Residence CEE

Related Parameters OPBIAS.FIX,OPBIAS.FLOAT,OPBIAS.RATE.

Remarks User may only store values to this parameter if the mode is

manual or if containing Control Module (CM) is inactive. Thefollowing occurs on a store to OPBIAS:

OPBIAS and OPBIAS.FIX are both set to a new value.

OPBIAS.FLOAT is set to zero.

OPBIAS[1..8]


Description Total Output Bias for function blocks with Multiple Outputs -OPBIAS is the sum of two components: a user-specified fixed

bias (OPBIAS[1..8].FIX) and a calculated floating bias(OPBIAS[1..8].FLOAT).



39/613

Oxxxx ParametersOPBIAS.FIX


Range N/A

Default N/A

Config Load No


Residence CEE

Related Parameters OPBIAS[1..8].FIX,OPBIAS[1..8].FLOAT,OPBIAS[1..8].RATE

Remarks

OPBIAS.FIX


Description Fixed Output Bias (in Engineering Units) - A user-specifiedbias that is applied to the function blocks Calculated Variable(CV).


Range N/A

Default 0.0

Config Load Yes


Residence CEE

Related Parameters OPBIAS,OPBIAS.FLOAT,OPBIAS.RATE.

Remarks CV = OP + OPBIAS.FIX + OPBIAS.FLOAT


40/613

Oxxxx ParametersOPBIAS[1..8].FIX


OPBIAS[1..8].FIX


Description Fixed Output Bias (in Engineering Units) - A user specifiedbias which is applied to the function blocks CalculatedVariables Outputs (CV[1..8]).


Range N/A

Default 0.0

Config Load Yes


Residence CEE

Related Parameters OPBIAS[1..8],OPBIAS[1..8].FLOAT,OPBIAS[1..8].RATE

Remarks

OPBIAS.FLOAT


Description Floating Output Bias (in Engineering Units) - Used inconjunction with OPBIAS.RATE.


Range N/A

Default N/A

Config Load No



41/613

Oxxxx ParametersOPBIAS[1..8].FLOAT


Residence CEE

Related Parameters OPBIAS,OPBIAS.FIX,OPBIAS.RATE.

Remarks Floating bias is calculated as follows:OPBIAS.FLOAT = CV(init) - (CV(unbiased) + OPBIAS.FIX)CV (init) = initialization value received from secondaryCV(unbiased) = unbiased calculated valueOPBIAS.FIX = fixed bias (user specified)

OPBIAS[1..8].FLOAT


Description Floating Output Bias (in Engineering Units) - Calculated biasfor each of Fanout Blocks output which is applied to thefunction blocks Calculated Variables Output (CV[1..8].OPBIAS[1..8].FLOAT is used to ensure a bumplesstransition, following initialization or mode change.


Range N/A

Default N/A

Config Load No


Residence CEE

Related Parameters OPBIAS[1..8],OPBIAS[1..8].FIX,OPBIAS[1..8].RATE

Remarks OPBIAS.FLOAT(new value) = OPBIAS.FLOAT(current value)- (OPBIAS.RATE/ cycles/min) where cycles per minute is thenumber of function block executions per minute.


42/613

Oxxxx ParametersOPBIAS.RATE


OPBIAS.RATE


Description Output Bias Ramp Rate (in Engineering Units per Minute) -Used in conjunction with OPBIAS.FLOAT to eliminate outputbumps when initialization path is done by the user.


Range N/A

Default NaN

Config Load Yes


Residence CEE

Related Parameters OPBIAS,OPBIAS.FIX,OPBIAS.FLOAT.

Remarks The Output Bias is the sum of two parts (OPBIAS.FIXED - a

fixed output bias, and OPBIAS.FLOAT - a calculated bias)and is generally used to ensure a bumpless transfer whenthe block initializes or changes mode.

OPBIAS[1..8].RATE


Description Output Bias Ramp Rate for function blocks with MultipleOutputs - There is a separate rate for each output when theinitialization path is broken by the user.


Range N/A

Default NaN


43/613

Oxxxx ParametersOPCHAR


Config Load Yes


Residence CEE

Related Parameters OPBIAS[1..8],OPBIAS[1..8].FIX,OPBIAS[1..8].FLOAT

Remarks

OPCHAR


Description Output Characterization. Specifies whether the outputcharacterization function is to be used for this data point ornot.

Data Type Boolean

Range Off: Output characterization is not to be used.

On: Output characterization is to be used.

Default Off

Config Load Yes


Residence IOP

Related Parameters

Remarks If OPCHAR is On, you must configure the values for theinput coordinates (OPIN1 to 4) and the output coordinates(OPOUT1 to 4). Refer to the Control Builder ComponentTheory document in Knowledge Builder for moreinformation on output characterization.

OPCHAR allows the user to ensure that between any two

points the OP value isdetermined by plotting OP to astraight line which connects the two points. Each point isdescribed as OPIN/OPOUT (X/Y) coordinate and theplotting of OP can be seen in the OPFINAL parameter.


44/613

Oxxxx ParametersOPCMD[0..2]


OPCMD[0..2]


Description Output Command

Data Type Boolean

Range Off (0)On (1)

Default Off (0)

Config Load No

Access Lock Program

Residence CEE

Related Parameters GOPREQ,OPREQ,OPTYPE.

Remarks If all the elements of OPCMD are Off, the OPREQ will be setto SAFEOP.

The priority of the OPCMD is determined by SAFEOP.

If SAFEOP = S0, then priority is 0, 1, 2.



OPDOMAP[0..3][1..3]


Description Output (OP) to Digital Output Values (DO) Map of SettableState Assignments.

Data Type Boolean

Range Off (0)On (1)

Default Off (0)


45/613

Oxxxx ParametersOPEU


Config Load Yes


Residence CEE

Related Parameters DO[1..3] ,GOP,GOPFINAL,NUMDOUTS,NUMSTATES,OP,OPFINAL,

PO[1..3].Remarks Illegal if NUMDOUTS = 0.

OPDOMAP[2, x] is illegal, if NUMSTATES = 2.

OPEU


Description Output Value (in Engineering Units)


Range N/A

Default N/A

Config Load No


Residence CEE

Related Parameters OP

Remarks


46/613

Oxxxx ParametersOPEU[1..8]


OPEU[1..8]


Description Output Values (in Engineering Units) for Function Blocks withMultiple Outputs - There is one value per output.


Range N/A

Default N/A

Config Load No


Residence CEE

Related Parameters OP[1..8]

Remarks

OPEUX


Description OPEU Value and Status

Data Type Structure

Range N/A

Default N/A

Config Load No


Residence CEE



47/613

Oxxxx ParametersOPEUX[1..8]


Remarks OPEUX is a hidden connection in Control Builder. Refer toControl Builder Components Theory, Outputsection of blockspecific documentation for more information.

OPEUX is a two-part data structure that contains: OPEU (theoutput value in engineering units) and a status component.OPEUX should be used when making a cascade connectionto a secondary control block. The OPEUX connection isrequired in order for the initialization path to be establishedbetween the primary and secondary blocks.

This parameter will not indicate any value (it shows )on the chart when the pin is exposed.

OPEUX[1..8]


Description OPEU Value and Status for function blocks with multipleoutputs.

Data Type Structure

Range N/A

Default N/A

Config Load No


Residence CEE

Related Parameters OP[1..8],OPEU[1..8].

Remarks


48/613

Oxxxx ParametersOPEXHIFL


OPEXHIFL


Description Output (OP) Extended High Limit Flag. Indicates if OP is atits extended high limit.

Data Type Boolean

Range Off (0): OP is below its extended high limit.

On (1): OP is at its extended high limit.

Default Off (0)

Config Load No


Residence CEE

Related Parameters OPEXHILM

Remarks

OPEXHIFL[1..8]


Description Output (OP) Extended High Limit Flag. Indicate if OP[1..8]are at their extended high limit.

Data Type Boolean

Range Off (0): Corresponding OP is below its extended high limit.On (1): Corresponding OP is at its extended high limit.

Default Off (0)

Config Load No


Residence CEE


49/613

Oxxxx ParametersOPEXHILM


Related Parameters OPEXHILM

Remarks

OPEXHILM

Specific to Block(s) All RegCtl Blocks: AutoMan, Fanout, OvrdSel, PID, PIDFF,PosProp, PulseCount, PulseLength, RampSoak, RemCas,RatioBias, RegCalc, and Switch.

Description Output (OP) Extended High Limit (in percentage)


Range Greater than OPLOLM

Default 106.9%

Config Load Yes


Residence CEE

Related Parameters OPEXHIFL

Remarks Only the Operator is permitted to specify an Output (OP)

value that exceeds the OPHILM value. Even the operator isprohibited from specifying values greater than the OPIXHILM,however.


50/613

Oxxxx ParametersOPEXLOFL


OPEXLOFL


Description Output (OP) Extended Low Limit Flag. Indicates if OP is atits extended low limit.

Data Type Boolean

Range Off (0): OP is above its extended low limit.

On (1): OP is at its extended low limit.

Default Off (0)

Config Load No


Residence CEE

Related Parameters OPEXLOLM

Remarks

OPEXLOFL[1..8]


Description Output (OP) Extended Low Limit Flag. Indicates if OP[1..8]are at their extended low limit.

Data Type Boolean

Range Off (0): Corresponding OP is above its extended low limit.On (1): Corresponding OP is at its extended low limit.

Default Off (0)

Config Load No


Residence CEE


51/613

Oxxxx ParametersOPEXLOLM


Related Parameters OPEXLOLM

Remarks

OPEXLOLM


Description Output (OP) Extended Low Limit (in percentage)


Range Less than OPHILM

Default -6.9%

Config Load Yes


Residence CEE

Related Parameters OPEXLOFL

Remarks


52/613

Oxxxx ParametersOPFINAL


OPFINAL


Description Field Output State

Data Type String



Config Load No


Residence CEE

Related Parameters DO[1..3],GOPFINAL,NUMDOUTS,NUMSTATES,NUMTRANS,OPDOMAP[0..3][1..3],SEALOPT,STATETEXT[0..6],STATETIME[0..2].

Remarks OPFINAL is a String set equal to STATETEXT (GOPFINAL).

Access is illegal if NUMDOUTS = 0.

STATETEXT[6] [State2] is illegal if NUMSTATES = 2.

Specific to Block(s) AOCHANNEL (PMIO), AO8, AO16

Description Output Final. Shows the final output value sent to thecontrol element after direct or reverse control action andoutput characterization have been applied.


Range N/A


Config Load No


53/613

Oxxxx ParametersOPFINAL[0..numChans-1]



Residence IOP

Related Parameters

Remarks If OPTDIR parameter configuration is DIRECT, 0.0 percentOP represents 4mA and 100 percent OP represents 20mA.

If OPTDIR parameter configuration is REVERSE, 0.0percent OP represents 20mA and 100 percent OPrepresents 4mA.

OPFINAL[0..numChans-1]

Specific to Block(s) AOM

Description Adjusted Output Value.


Range N/A

Default 0

Config Load No


Residence CEE

Related Parameters

Remarks


54/613

Oxxxx ParametersOPHIALM.DB


OPHIALM.DB


Description Output (OP) High Alarm Deadband


Range 0.0 to 100.0 if alarm deadband units (OPHILAM.DBU) arePercent.

CVEULO to CVEUHI if alarm deadband units(OPHIALM.DBU) are Engineering Units.

Default 0.0

Config Load Yes

Access Lock Engineer/Application Developer

Residence CEE

Related Parameters OP,OPHIALM.DBU,OPHIALM.FL,OPHIALM.PR,OPHIALM.SV,OPHIALM.TM,OPHIALM.TP.

Remarks The following rule is applied to OPHIALM.DB to prevent OPHIand OPLO alarm are both active at the same time:

OPHIALM.DB


55/613

Oxxxx ParametersOPHIALM.DBU


parameters to the three configured values.

When OPHIALM.DB is in Percent, the deadband units(OPHIALM.DBU) cannot be changed.

OPHIALM.DBU


Description Output (OP) High Alarm Deadband Units - Indicates ifOPHILAM.DB is in Percent or Engineering Units.

Data Type Enumeration ALMDBU

Range Percent (0)EU (1)

Default Percent (0)

Config Load Yes


Residence CEE

Related Parameters OP,OPHIALM.DB,OPHIALM.FL,OPHIALM.PR,OPHIALM.SV,OPHIALM.TM,OPHIALM.TP.

Remarks Individual alarm deadbands are not individually configurable.The ALMDB that is configured is loaded to the block, then theblock copies the ALMDB value to all the xxALM.DB of allanalog alarms on the block. This includes ALMDBU and

ALMTM - thus, all analog alarms get the same three valuesthrough a one-time configuration entering of the three values.

If desired, the individual alarm parameters (xxALM.DB,

xxALM.DBU, and xxALM.TM) may be modified after the blockis loaded. The block load will always set all individual alarmparameters to the three configured values.


56/613

Oxxxx ParametersOPHIALM.FL


OPHIALM.FL


Description OP High Alarm Flag

Data Type Boolean

Range Off (0) (not in OP High alarm)

On (1) (in Op High alarm)

Default Off (0)

Config Load No


Residence CEE

Related Parameters OP,OPHIALM.DB,OPHIALM.DBU,OPHIALM.PR,OPHIALM.SV,OPHIALM.TM,OPHIALM.TP.

Remarks

OPHIALM.PR


Description Output (OP) High Alarm Priority




57/613

Oxxxx ParametersOPHIALM.SV


Default Low (2)

Config Load Yes


Residence CEE

Related Parameters OP,OPHIALM.DB,OPHIALM.DBU,OPHIALM.FL,OPHIALM.SV,OPHIALM.TM,OPHIALM.TP.

Remarks

OPHIALM.SV


Description Output (OP) High Alarm Severity


Range 0 to 15

Default 0

Config Load Yes


Residence CEE

Related Parameters OP,OPHIALM.DB,OPHIALM.DBU,OPHIALM.FL,OPHIALM.PR,

OPHIALM.TM,OPHIALM.TP.

Remarks


58/613

Oxxxx ParametersOPHIALM.TM


OPHIALM.TM


Description Output (OP) High Alarm Filter Time (in seconds) - Thepurpose of this variable is to prevent input spikes fromcausing OP High alarms. An alarm will only be generated ifthe OP consistently exceeds the high trip point for more thanthe configured alarm filter time.

Data Type 32-Bit Unsigned Integer

Range 0 to 60

Default 0

Config Load Yes


Residence CEE

Related Parameters OP,OPHIALM.DB,OPHIALM.DBU,

OPHIALM.FL,OPHIALM.PR,OPHIALM.SV,OPHIALM.TP.

Remarks If OPHIALM.TM = 0, alarm will be generated as soon as OPexceeds the high trip point.

Individual alarm deadbands are not individually configurable.The ALMDB that is configured is loaded to the block, then theblock copies the ALMDB value to all the xxALM.DB of allanalog alarms on the block. This includes ALMDBU and





59/613

Oxxxx ParametersOPHIALM.TP


OPHIALM.TP


Description Output (OP) High Alarm Trip Point (in Percent)


Range NaN, or OPLOLM to OPEXHILM

Default NaN

Config Load Yes


Residence CEE

Related Parameters OP,OPHIALM.DB,OPHIALM.DBU,OPHIALM.FL,OPHIALM.PR,OPHIALM.SV,OPHIALM.TM.

Remarks If OPHIALM.TP = NaN, OP high alarms are inhibited.

The following restriction is applied to OPHIALM.TP to preventthat OPHI and OPLO alarm are both active at the same time:

OPHIALM.DB = OPLOALM.TP + 2 OPHIALM.DB)


60/613

Oxxxx ParametersOPHIFL


OPHIFL


Description Output (OP) High Limit Flag - Indicates if OP has reached thehigh limit, as specified by OPHILM.

Data Type Boolean

Range Off (0): Output has not reached the high limit.

On (1): Output has reached the high limit.

Default Off (0)

Config Load No


Residence CEE

Related Parameters OPHILM

Remarks

OPHIFL[1..8]


Description Output (OP) High Limit Flag Indicates if OP[1..8] havereached the high limit, as specified by OPHILM.

Data Type Boolean

Range Off (0): Output has not reached the high limit.

On (1): Output has reached the high limit.

Default Off (0)

Config Load No



61/613

Oxxxx ParametersOPHILM


Residence CEE

Related Parameters OPHILM

Remarks

OPHILM


Description Output (OP) High Limit (in percentage)


Range NaN, or OPLOLM to OPEXHILM

Default 105.0%

Config Load Yes


Residence CEE

Related Parameters OPHIFL

Remarks Entering NaN disables limit checking.

Only the operator is permitted to specify an OP value thatexceeds the OPHILM value. Programs (SCM, etc.) canspecify output values up to the OPHILM limit. If values largerthan this are requested, then they are clamped at theOPHILM value.


62/613

Oxxxx ParametersOPIN


OPIN

Specific to Block(s) UCNOUT

Description Output Value in Percent Input - Shows the value broughtfrom the primary in percent.

Data Type Float64


Default N/A

Config Load No


Residence ACE

Related Parameters OPOUT,REMCASTYPE.

Remarks

OPIN0


Description Input Coordinate Number 0. Defines the number 0 Inputcoordinate in percent for the output when the OPCHARparameter is On.


Range N/A

Default Fixed at 6.9 percent

Config Load Yes


Residence IOP

Related Parameters


63/613

Oxxxx ParametersOPIN1


Remarks This paramter can only be set when PTEXECST isINACTIVE.

See the Control Builder Component Theorydocument inKnowledge Builder for more information.

OPIN1


Description Input Coordinate Number 1. Specifies the number 1 Input

coordinate in percent for the output when the OPCHARparameter is On.


Range Greater than previous coordinate; Less than nextcoordinate.

Default NaN

Config Load Yes


Residence IOP

Related Parameters




64/613



OPIN2


Description Input Coordinate Number 2. Specifies the number 2 Inputcoordinate in percent for the output when the OPCHARparameter is On.



Default NaN

Config Load Yes


Residence IOP

Related Parameters



OPIN3





Default NaN

Config Load Yes


65/613




Residence IOP

Related Parameters



OPIN4





Default NaN

Config Load Yes


Residence IOP

Related Parameters




66/613



OPIN5




Range N/A


Config Load Yes


Residence IOP

Related Parameters

Remarks

OPINITVAL


Description OP Initialize Value. Defines the pulsed output value fromthe IOP in percent.


Range 0.0 to 100.0 percent

Default 0.0 percent

Config Load No


Residence IOP



67/613

Oxxxx ParametersOPINITVAL


Remarks The data is available only when DOPTYPE is configured asPWM.

Pulse on-time is calculated as follows.

For DIRECT action:

Pulse On-Time = (OP percent x PERIOD) / 100

For REVERSE action:

Pulse On-Time = (100 percent - OP percent x PERIOD) /100


68/613

Oxxxx ParametersOPLOALM.DB


OPLOALM.DB


Description Output (OP) Low Alarm Deadband


Range 0.0 to 100.0 if alarm deadband units (OPLOALM.DBU) arePercent.

CVEULO to CVEUHI if alarm deadband units(OPLOALM.DBU) are EUs.

Default 0.0

Config Load Yes


Residence CEE

Related Parameters OP,OPLOALM.DBU,OPLOALM.FL,OPLOALM.PR,OPLOALM.SV,OPLOALM.TM,OPLOALM.TP.


69/613

Oxxxx ParametersOPLOALM.DB


Remarks The following restriction is applied to OPLOALM.DB toprevent that OPHI and OPLO alarm are both active at thesame time:

OPLOALM.DB


70/613

Oxxxx ParametersOPLOALM.DBU


OPLOALM.DBU


Description Output (OP) Low Alarm Deadband Units - Indicates ifOPLOALM.DB is in Percent or Engineering Units.

Data Type Enumeration ALMDBU

Range Percent (0)EU (1)

Default Percent (0)

Config Load Yes


Residence CEE

Related Parameters OP,OPLOALM.DB,OPLOALM.FL,OPLOALM.PR,OPLOALM.SV,

OPLOALM.TM,OPLOALM.TP.

Remarks Individual alarm deadbands are not individually configurable.The ALMDB that is configured is loaded to the block, then theblock copies the ALMDB value to all the xxALM.DB of allanalog alarms on the block. This includes ALMDBU and


If desired, the individual alarm parameters (xxALM.DB,xxALM.DBU, and xxALM.TM) may be modified after the blockis loaded. The block load will always set all individual alarmparameters to the three configured values.


71/613

Oxxxx ParametersOPLOALM.FL


OPLOALM.FL


Description Output (OP) Low Alarm Flag

Data Type Boolean

Range Off (0): Not in OP Low alarm.

On (1): In OP Low alarm.

Default Off (0)

Config Load No


Residence CEE

Related Parameters OP,OPLOALM.DB,OPLOALM.DBU,OPLOALM.PR,OPLOALM.SV,

OPLOALM.TM,OPLOALM.TP.

Remarks


72/613

Oxxxx ParametersOPLOALM.PR


OPLOALM.PR


Description Output (OP) Low Alarm Priority



Default Low (2)

Config Load Engineer

Access Lock Yes

Residence CEE

Related Parameters OP,OPLOALM.DB,OPLOALM.DBU,

OPLOALM.FL,OPLOALM.SV,OPLOALM.TM,OPLOALM.TP.

Remarks


73/613

Oxxxx ParametersOPLOALM.SV


OPLOALM.SV


Description Output (OP) Low Alarm Severity


Range 0 to 15

Default 0

Config Load Yes


Residence CEE

Related Parameters OP,OPLOALM.DB,OPLOALM.DBU,OPLOALM.FL,OPLOALM.PR,OPLOALM.TM,OPLOALM.TP.

Remarks


74/613

Oxxxx ParametersOPLOALM.TM


OPLOALM.TM


Description Output (OP) Low Alarm Filter Time (in seconds) - Thepurpose of this variable is to prevent input spikes fromcausing OP Low alarms. An alarm will only be generated ifthe OP is consistently below the low trip point for more thanthe configured alarm filter time.

Data Type 32-Bit Unsigned Integer

Range 0 to 60

Default 0

Config Load Yes

Access Lock EngineerApplication Developer

Residence CEE

Related Parameters OP,OPLOALM.DB,OPLOALM.DBU,

OPLOALM.FL,OPLOALM.PR,OPLOALM.SV,OPLOALM.TP.

Remarks If OPLOALM.TM = 0, an alarm will be generated as soon asOP falls below the low trip point.

Individual alarm deadbands are not individually configurable.The ALMDB that is configured is loaded to the block, then theblock copies the ALMDB value to all the xxALM.DB of allanalog alarms on the block. This includes ALMDBU and





75/613

Oxxxx ParametersOPLOALM.TP


OPLOALM.TP


Description Output (OP) Low Alarm Trip Point (in percentage)


Range NaN, or OPEXLOLM to OPEXHILM

Default NaN

Config Load Yes


Residence CEE

Related Parameters OP,OPLOALM.DB,OPLOALM.DBU,OPLOALM.FL,OPLOALM.PR,OPLOALM.SV,OPLOALM.TM.

Remarks If OPLOALM.TP = NaN, OP low alarms are inhibited.

The following restriction is applied to OPLOALM.TP toprevent that OPHI and OPLO alarm are both active at thesame time:

OPLOALM.DB


76/613

Oxxxx ParametersOPLOFL


OPLOFL


Description Output (OP) Low Limit Flag - Indicates if OP has reached itslow limit, as specified by OPLOLM.

Data Type Boolean

Range Off (0): Output has not reached the low limit.

On (1): Output has reached the low limit.

Default Off (0)

Config Load No


Residence CEE

Related Parameters OPLOLM

Remarks

OPLOFL[1..8]


Description Output (OP) Low Limit Flag - Indicates if OP[1..8] havereached its low limit, as specified by OPLOLM.

Data Type Boolean

Range Off (0): Output has not reached the low limit.

On (1): Output has reached the low limit.

Default Off (0)

Config Load No



77/613

Oxxxx ParametersOPLOLM


Residence CEE

Related Parameters OPLOLM

Remarks

OPLOLM


Description Output (OP) Low Limit (in percentage)


Range NaN, or OPEXLOLM to OPHILM

Default -5.0%

Config Load Yes


Residence CEE

Related Parameters OPLOFL



78/613

Oxxxx ParametersOPMINCHG


OPMINCHG


Description Output (OP) Minimum Change Limit (in Percent)


Range NaN, or a real number greater than or less than zero.

Default 0.0%

Config Load Yes


Residence CEE


Remarks Defines the minimum amount that the output must changebefore the function blocks actually change the OP. If thisvalue is NaN, then there is no minimum limit set.

Entering NaN disables limit checking.

OPNUMSRCCONN[1..16]

Specific to Block(s) Step Block

Description Number of Source Connections for Output expression.Represents number of source references in the expressionof Output i, where iis the parameter index from 1..16.

Data Type Integer32

Range 0 to 200

Default 0

Config Load Yes

Access Lock Application Developer Only


79/613

Oxxxx ParametersOPOUT0


Residence ACE/CPM/SCE

Related Parameters OPPCODESIZE[1..16]

Remarks

OPOUT0


Description Output Coordinate Number 0. Defines the number 0

Output coordinate in percent for the output when theOPCHAR parameter is On.


Range N/A


Config Load Yes


Residence IOP

Related Parameters

Remarks This parameter can only be set when PTEXECST isINACTIVE.



80/613



OPOUT1


Description Output Coordinate Number 1. Specifies the number 1output coordinate in percent for the output when theOPCHAR parameter is On.


Range Greater than previous coordinate; Less than nextcoordinate

Default NaN

Config Load Yes


Residence IOP

Related Parameters



OPOUT2


Description Output Coordinate Number 2. Specifies the number 2Output coordinate in percent for the output when theOPCHAR parameter is On.


Range Greater than previous coordinate; Less than nextcoordinate

Default NaN

Config Load Yes


81/613




Residence IOP

Related Parameters



OPOUT3





Default NaN

Config Load Yes


Residence IOP

Related Parameters




82/613



OPOUT4





Default NaN

Config Load Yes


Residence IOP

Related Parameters



OPOUT5




Range N/A


Config Load Yes



83/613

Oxxxx ParametersOPOUT


Residence IOP

Related Parameters

Remarks

OPOUT

Specific to Block(s) UCNOUT

Description Output Value sent to UCN - Indicates the output value that

is being stored to the UCN Process Manager in percent.

Data Type Floata64


Default N/A

Config Load No


Residence ACE

Related Parameters OPIN,REMCASTYPE.

Remarks


84/613

Oxxxx ParametersOPPCODESIZE[1..16]


OPPCODESIZE[1..16]

Specific to Block(s) Step Block

Description Number of Pcode Bytes for Output expression. Representsnumber of bytes required for the Psuedo code for theexpression of Output i, where iis the parameter index from1..16.

Data Type Integer32

Range 0 to 200

Default 0

Config Load Yes

Access Lock Application Developer Only

Residence ACE/CPM/SCE

Related Parameters OPNUMSRCCONN[1..16]

Remarks

OPREQSpecific to Block(s) All RegCtl Blocks: AutoMan, Fanout, OvrdSel, PID, PIDFF,

PosProp, PulseCount, PulseLength, RampSoak, RemCas,RatioBias, RegCalc, and Switch.

Description The requested OP (Output) value. The SCM CONTROLREQwants to change the regulatory control blocks output (OP).



Default 0

Config Load No


Residence CEE


85/613

Oxxxx ParametersOPREQ


Related Parameters CONTROLREQ,HOLDOPT,LASTOPMNAME,LASTOPREQ,LASTOPTYPE,RESTARTOPT,SCMOPT,STOPOPT.

Remarks OPREQ is illegal if ControlModule. SCMOPT = None.

While MODEATTR is Operator, a pending OPREQ can beterminated by the operator setting it to NaN.


Description The Output State Requested

Data Type String



Config Load No

Access Lock Other Function Block

Residence CEE

Related Parameters GOP,GOPREQ,HOLDOPT,LASTOPMNAME,LASTOPREQ,MODEATTR,NUMSTATES,OP,OPTYPE,RESTARTOPT,SAFEOP,STARTOPT,STATETEXT[0..6],STOPOPT.


86/613

Oxxxx ParametersOPROCLM


Remarks OPREQ is a String set equal to STATETEXT(GOPREQ).

If OPTYPE = Set, and MODEATTR is Operator, the Engineermay change OPREQ.

STATETEXT[6] is illegal if NUMSTATES = 2

OPROCLM

Specific to Block(s) All RegCtl Blocks: AutoMan, Fanout, OvrdSel, PID, PIDFF,PosProp, PulseCount, PulseLength, RampSoak, RemCas,

RatioBias, RegCalc, and Switch.

Description Output (OP) Rate of Change Limit (in Percent per minute)


Range NaN, or Greater-than or equal-to 0.1

Default NaN

Config Load Yes


Residence CEE

Related Parameters OPROCNEGFL,OPROCPOSFL.


OPROCNEGFL


Description Output (OP) Negative Rate of Change Flag

Data Type Boolean

Range Off (0): OP negative rate of change is above the limit.

On (1): OP negative rate of change is less-than or equal-to


87/613

Oxxxx ParametersOPROCNEGFL[1..8]


the limit.

Default Off (0)

Config Load No


Residence CEE

Related Parameters OPROCLM

Remarks

OPROCNEGFL[1..8]


Description Output (OP) Negative Rate of Change Flag

Data Type Boolean

Range Off (0): OP negative rate of change is above the limit.

On (1): OP negative rate of change is below or equal to thethe limit.

Default Off (0)

Config Load No


Residence CEE


Remarks This flag is set when the Output rate of change exceedsOPROCLM in the negative direction


88/613

Oxxxx ParametersOPROCPOSFL


OPROCPOSFL


Description Output (OP) Positive Rate of Change Flag

Data Type Boolean

Range Off (0): OP positive rate of change is below the limit.

On (1): OP positive rate of change is above or equal to thelimit.

Default Off (0)

Config Load No


Residence CEE


Remarks

OPROCPOSFL[1..8]


Description Output (OP) Positive Rate of Change Flag

Data Type Boolean

Range Off (0): OP positive rate of change is < the limit.

On (1): OP positive rate of change is >= the limit.

Default Off (0)

Config Load No


Residence CEE


89/613

Oxxxx ParametersOPSECDATA



Remarks This flag is set when the Output rate of change exceedsOPROCLM in the positive direction.

OPSECDATA



Data Type

Range

Default

Config Load

Access Lock

Residence

Related Parameters

Remarks


90/613

Oxxxx ParametersOPSECDATA[1..8]


OPSECDATA[1..8]



Data Type

Range

Default

Config Load

Access Lock

Residence

Related Parameters

Remarks

OPSECDATA.ARWSTS


Description

Data Type Integer

Range N/A

Default 0

Config Load


Residence

Related Parameters

Remarks


91/613

Oxxxx ParametersOPSECDATA.EUHI


OPSECDATA.EUHI


Description

Data Type Real

Range N/A

Default NaN

Config Load


Residence

Related Parameters

Remarks

OPSECDATA.EULO


Description

Data Type Real

Range N/A

Default NaN

Config Load


Residence

Related Parameters

Remarks


92/613

Oxxxx ParametersOPSECDATA.INITREQ


OPSECDATA.INITREQ


Description

Data Type Boolean

Range Off (0)On (1)

Default Off (0)

Config Load


Residence

Related Parameters

Remarks

OPSECDATA.INITVAL


Description

Data Type Real

Range N/A

Default NaN

Config Load


Residence

Related Parameters

Remarks


93/613

Oxxxx ParametersOPSECDATA.ONESHOT


OPSECDATA.ONESHOT


Description

Data Type Integer

Range N/A

Default 0

Config Load


Residence

Related Parameters

Remarks


94/613

Oxxxx ParametersOPSECDATA.ORFBVA


OPSECDATA.ORFBVA


Description


Range N/A

Default NaN

Config Load


Residence

Related Parameters

Remarks

OPSECDATA.OROFFS


Description

Data Type Boolean

Range Off (0)On (1)

Default Off (0)

Config Load


Residence

Related Parameters


95/613

Oxxxx ParametersOPSOURCE


Remarks

OPSOURCE

Specific to Block(s) AOC, PWM Channel

Description Output Source Connector

Data Type

Range

Default

Config Load


Residence

Related Parameters

Remarks

OPSRC[1..16][1..6]



Data Type

Range

Default

Config Load

Access Lock

Residence

Related Parameters

Remarks


96/613

Oxxxx ParametersOPTDIR


OPTDIR


Description Output (OP) Direction. Specifies the whether the PWMdigital output action is to be direct or reverse.

Data Type Enum

Range DIRECT(0): OP is the percent On time.

REVERSE(1): OP is the percent Off time.

Default DIRECT(0)

Config Load Yes


Residence IOP

Related Parameters

Remarks


Description Output Direction. Defines the output action of the

OPFINAL value for the data point as either Direct orReverse.

Data Type Enum

DIRECT (0): For OPFINAL, 0% = 4mA and 100% =20mA.

Range

REVERSE (1): For OPFINAL, 0% = 20mA and 100% =4mA.

Default DIRECT (0)

Config Load Yes


Residence IOP

Related Parameters


97/613

Oxxxx ParametersOPTYPE


Remarks

OPTYPE

Specific to Block(s) DevCtl,

All RegCtl Blocks: AutoMan, Fanout, OvrdSel, PID, PIDFF,PosProp, PulseCount, PulseLength, RampSoak, RemCas,RatioBias, RegCalc, and Switch.

Description Sequential Control Module (SCM) Control Output Request

Type Option

Data Type Enumeration OPTYPE

Range Null (0)Set (1)NotStored (2)Default (3)

Default Null (0)

Config Load No


Residence CEE

Related Parameters RegCtl only:ASTEPID,CONTROLREQ,LASTOPTYPE,OP[1..16].TYPE,SCMASTEP[1..10],SCMOPT,SCMSTATE.

DevCtl only:HOLDOPT,LASTOPTYPE,OPREQ,RESTARTOPT,

STARTOPT,STOPOPT.

Remarks


98/613

Oxxxx ParametersOPX


OPX


Description Output (OP) Value in Percent and Status.

Data Type Structure

Range N/A

Default N/A

Config Load No


Residence CEE


Remarks OPX is a two-part data structure that contains: OP (the outputvalue in percent) and a status component. OPX can be usedwhen making a connection to an AOC block. The OPXconnection is required in order for the initialization path to beestablished between the Regulatory Control (RegCtl) block

and the AOC block.

OPEUX can also be used in the same capacity as the OPXparameter.

This parameter w

EP-DCX101v3 Control Builder

Documents

Transcript of EP-DCX101v3 Control Builder