EP 1110-1-8 (Vol. 4), Construction Equipment …...DEPARTMENT OF THE ARMY EP 1110-1-8 U.S. Army...

Construction Equipment Ownership and Operating Expense Schedule Region IV

EP 1110-1-8 Volume 4

November 2011

CECW-EC

DEPARTMENT OF THE ARMY U.S. Army Corps of Engineers Washington, DC 20314-1000

MEMORANDUM FOR SEE DISTRIBUTION

SUBJECT: Construction Equipment Ownership and Operating Expense Schedule

FEB 2 3 2012

1. Purpose. This pamphlet is authorized by and established in accordance with Federal Acquisition Regulation (FAR) 31.105 and Engineer Federal Acquisition Regulation (EFAR) SlIBPART 31.105. This pamphlet establishes predetermined equipment ownership and operating expense rates for construction equipment. This pamphlet also establishes a method to calculate equipment ownership and operating expense rates for construction equipment when the predetermined rates are not considered appropriate. The overall intent of this pamphlet is to determine equipment costs that are fair and reasonable. Expense factors for calculating dredge plant and marine equipment costs are provided in chapter 4.

2. Applicability. This pamphlet supersedes EP 1110-1-8, dated 30 November 2009. This pamphlet applies to all USACE commands. It is applicable to all solicitations and contracts for construction expected to exceed the Simplified Acquisition Threshold of $150,000 when actual cost data for both ownership and operating costs cannot be determined. This volume is for use in Region IV, which includes the following states:

Iowa (North of U.S. Highway 20) Michigan (Upper Peninsula) Minnesota Montana North Dakota

3. References. See APPENDIX A.

South Dakota Wisconsin Wyoming

4. Distribution Statement. Approved for public release, distribution is unlimited.

FOR THE COMMANDER:

Encl lonel, Corps of Engineers

hief of Staff

DEPARTMENT OF THE ARMY EP 1110-1-8 U.S. Army Corps of Engineers

CECW-EC Washington, DC 20314-1000 Pamphlet No. 1110-1-8, Vol. 4 30 November 2011

Engineering and Design CONSTRUCTION EQUIPMENT OWNERSHIP AND

OPERATING EXPENSE SCHEDULE

TABLE OF CONTENTS

Paragraph Page

Chapter 1. Introduction

Use 1.1 1-1 Decision Flow Process 1.2 1-1 How to Obtain Assistance 1.3 1-1 How to Obtain CHECKRATE Spreadsheet 1.4 1-1 How to Obtain this Publication 1.5 1-2

Chapter 2. Methodology for Construction Equipment

Contents 2.1 2-1 Basis for Equipment Rates 2.2 2-1 Total Hourly Rate 2.3 2-1 Average, Difficult, or Severe Conditions 2.4 2-2 Determination of Condition 2.5 2-2 General 2.6 2-2 Truck Selection 2.7 2-3 Crawler Tractor Selection 2.8 2-3 Equipment Accessories 2.9 2-3 List Price and Accessories 2.10 2-3 Discount Code (DC) 2.11 2-3 Sales or Import Tax 2.12 2-3 Freight 2.13 2-4 Total Equipment Value 2.14 2-4 Economic Life (LIFE) 2.15 2-4 Working Hours Per Year (WHPY) 2.16 2-4 Salvage Value (SLV) 2.17 2-4 Salvage Value Percentage 2.18 2-4 Owernship Elements 2.19 2-5 Depreciation 2.20 2-5 Facilities Capital Cost of Money (FCCM) 2.21 2-5 Operating Cost Elements 2.22 2-6

ii

Fuel Cost 2.23 2-6 Filters, Oil, and Grease 2.24 2-8 Repair cost 2.25 2-9 Tire Wear Cost 2.26 2-10 Tire Repair Cost 2.27 2-11 Standby Hourly Rate 2.28 2-11 Computation Example 2.29 2-12

Chapter 3. Adjustments to Hourly Rates

Contents 3.1 3-1 Basis for Equipment Rates 3.2 3-1 Equipment Rate Adjustment Tables 3.3 3-1 Determination for Use of Equipment Rates in Tables 2-1

and 2-2 3.4 3-1 Rate Adjustments 3.5 3-1 Changes in Operating Conditions 3.6 3-2 Change in Cost of Money Rate (CMR) 3.7 3-2 Actual Work Hours Greater than 40 Hours per Week 3.8 3-3 Changes in Fuel Cost 3.9 3-3 Adjustments to Fuel, Oil, and Grease (FOG) Cost 3.10 3-4 Equipment of Different Age than Table 2-1 3.11 3-4 Rate Adjustment for Overage Equipment 3.12 3-5 Standby Rate Adjustment for Equipment of a Different Age

than Table 2-1 3.13 3-6 Equipment Purchased Used 3.14 3-7 Rate Calculation Examples 3.15 3-7

Chapter 4. Methodology for Dredging Plant and Marine Equipment

Contents 4.1 4-1 General 4.2 4-1 Time Available to Dredge 4.3 4-1 Life 4.4 4-2 Annual Hours Available 4.5 4-2 Salvage Value (SLV) 4.6 4-3 Ownership Cost 4.7 4-3 Depreciation Factor 4.8 4-4 The Cost of Money Rate (CMR) 4.9 4-4 Other Ownership Elements 4.10 4-4 Hourly Operating Cost 4.11 4-4 Prime and Secondary Power 4.12 4-4 Water, Lube, and Supplies (WLS) 4.13 4-5 Repairs (RPR) 4.14 4-5

EP 1110-1-8, Vol. 430 Nov 11

iii

Standby Rate 4.15 4-6 Rates 4.16 4-6 Allowance for Additional Capital Improvements 4.17 4-6 Overage Plant 4.18 4-7 Dredging Plant Purchased Used 4.19 4-7 Rate Calculation Example 4.20 4-7

Appendix A - References A-1 Appendix B - Area Factors B-1 Appendix C - Guide for Selecting Operating Conditions C-1 Appendix D - Equipment Hourly Calculation Factors D-1 Appendix E - Economic Indexes for Construction Equipment E-1 Appendix F - Tire Description and Tire Cost F-1 Appendix G - Tire Life and Tire Wear Factors G-1 Appendix H - Manufacturer List H-1 Appendix I - Federal Cost-of-Money Rate I-1 Appendix J - Equipment Accessories J-1 Appendix K - Ground Engaging Component Costs Included in Repairs (RCF) K-1 Appendix L - Guide for Estimating Drill Steel and Drill Bit Costs L-1 Glossary Glossary-1 Index Index-1

EP 1110-1-8, Vol. 430 Nov 11

[This page intentionally left blank]

EP 1110-1-8, Vol. 430 Nov 11

iv

1-1

CHAPTER 1

Introduction

1.1 Use. The use of this pamphlet is for rate determination on construction contracts, dredging contracts, and negotiated procurements and relates only to contractor-owned equipment. The overall intent of the pamphlet is to determine equipment costs that are fair and reasonable.

a. This pamphlet shall be used for determining hourly equipment rates that are contained in the independent government estimate.

b. In addition, the use of this pamphlet will be required by contractors for pricing contractor-owned equipment in negotiated procurements when:

(1) Cost or pricing data is not required, as defined in Federal Acquisition Regulation (FAR) Part 15.4, Contract Pricing.

(2) Cost or pricing data is required and the actual cost data to support either ownership or operating costs for equipment or equipment groups of similar model and series is not available.

(3) Cost or pricing data is required and available, but all or part of the data is determined not to be in accordance with the FAR cost principles.

1.2 Decision Flow Process. A flow chart (figure 1-1) is provided at the end of this chapter to help the user better understand the process for developing an hourly equipment rate. The flow chart shows the decision points that allow the user to decide whether to use the predetermined rate tables or calculate the rate using the method shown in figure 2-1 or using CHECKRATE (also see paragraph 3.4).

1.3 How to Obtain Assistance. When assistance is needed in understanding the methodology for calculating equipment rates, contact the Chief, Cost Engineering Branch, Engineering and Construction Division, Walla Walla District, U.S. Army Corps of Engineers, (CENWW-EC-X), 509-527-7511, 509-527-7510, or visit the Web site at http://www.nww.usace.army.mil/html/offices/ed/c/default.asp.

1.4 How to Obtain CHECKRATE Spreadsheet. A Microsoft Excel® spreadsheet, named “CHECKRATE,” has been developed to calculate equipment rates using the methodology required by this pamphlet. The user must have Microsoft Excel® to run the application. The factors needed in the hourly cost calculations are located in the appendixes of this pamphlet. A copy of the spreadsheet may be obtained by choosing the CHECKRATE link on the following Web site: http://www.nww.usace.army.mil/html/offices/ed/c/default.asp.

EP 1110-1-8, Vol. 430 Nov 11

1-2

1.5 How to Obtain this Publication. Volumes 1-12 of this pamphlet are available in portable document format (PDF) and can be viewed or downloaded at http://140.194.76.129/publications/eng-pamphlets. Additional instructions in Appendix A.

EP 1110-1-8, Vol. 430 Nov 11

Finished. The methodology in ths pamphlet should not be used for rental or leased equipment.

YES

YES

AVERAGE SEVERE

NO

YES

NO

DIFFICULT

Is the equipment contractor owned ?

Is the equipment in Table 2-1?

Is there equipment in Table 2-1 that is equivalent in configuration (size, capacity,

and horsepower) and value to the equipment for which you are determining a

rate?

Use the tables in chapter 2 for the actual or equivalent

equipment.

Is the equipment operating in average severe or difficult conditions? (see

chapter 2, section II for definition and EFARS clause 31.231-5000 appendix A

for determining authority)

Calculate a rate based on the step-by-step rate computation method shown in Figure 2-

1 or use CHECKRATE

Use the equipment rate shown in Table 2-1

From Table 2-2 use the arithmetic mean of the average and severe equipment rates.

(Note: if there is no severe rate for the equipment see guidance in chapter 2,

section II, paragraph 2-4.)

Use severe rate shown in Table 2-2. (Note: if there is no severe

rate for the equipment see guidance in chapter 2, section II,

paragraph 2-4.)

Is the use of this pamphlet required in accordance with Chapter 1, paragraph

1-1?

YES

NO

Use the contractor's actual cost and pricing data to determine a rate.NO

Figure 1-1. Methodology for Developing an Hourly Ownership and Operating Rate for Construction Equipment

START

Next Page

Is this land based or marine equipment?Land Based Equipment Marine equipment Use the methodology found in Chapter 4 for

determining a rate for Marine Equipment.

Is the equipment in Table 2-1 equivalent in configuration (size,

capacity, and horsepower) and value to the equipment for which you are

determining a rate?

YES

1-3

EP 1110-1-8, Vol. 430 Nov 11

NO

YES

NO

NO

FINISHED (except for standby)

YES

NO

Equipment is newer

If equipment is older than in Table 2-1 determine economic life by dividing LIFE by Working Hours Per Year. (see

chapter3 section II, Paragraph 3-11.a.)

Equipment is older

Equipment age does not exceed economic life Equipment age exceeds economic life

Is the Cost of Money Rate (CMR) different from that shown in chapter 2, section VII or Appendix B?

The Department of the Treasury adjusts the CMR (Prompt Payment Interest Rate) on or about 1 January and 1 July each year. For the current

Prompt Payment Interest Rate seehttp://www.publicdebt.treas.gov/opd/opdprmt2.htm.

If the cost of money rate shown in chapter 2, section VII, is not the current rate, the FCCM portion of the total hourly rate shall be adjusted. Adjust the Cost

of Money Rate per the instructions in chapter 3, section II, paragraph 3-7.

Is the cost of fuel 10% greater than or 10% less than the cost shown in Appendix B?

The contractor shall be required to furnish copies of all fuel supply contracts and invoices to the government to

support fuel cost adjustment. Request for upward adjustment in the rates will be considered only when fuel is supplied by recognized distributors of bulk quantities

If the contractor is able to furnish the above information, adjust the fuel cost per the instructions in chapter 3,

section II, paragraph 3-9.

If fuel costs are adjusted FOG costs also need to be adjusted by applying the same ratio used to adjust the

fuel cost.

Do the actual hours worked exceed 40 hours per week?

Make adjustments to the FCCM per the instructions in chapter 3,

section II, paragraph 3-8

Is the equipment's date of manufacure different from that in

Table 2-1 (see chapter 2 section 1, paragraph 2-2)?

Adjust the rate using Table 3-1 per the

instructions found in chapter3 section II, Paragraph 3-11.c.

Adjust the rate using Table 3-1 per the example found

in chapter3 section II, Paragraph 3-11.a.

Adjust the rate using Table 3-1 per the

instructions found in chapter3 section II,

Paragraph 3-12.

YES

Figure 1-1. Methodology for Developing an Hourly Ownership and Operating Rate for Construction Equipment

Continue from

previous page

1-4

EP 1110-1-8, Vol. 430 Nov 11

2-1

CHAPTER 2

Methodology for Construction Equipment

SECTION I. GENERAL

2.1 Contents. This chapter provides the methodology used to compute the total hourly ownership and operating rates for construction equipment and marine equipment (except dredging plant). This detailed methodology includes the formulas and factors used to develop both total hourly rates and hourly standby rates. If the equipment is determined to be older than its estimated economic life (overage) or was purchased used, refer to chapter 3.

2.2 Basis for Equipment Rates. The hourly rates shown in table 2-1 reflect catalog list prices of equipment manufactured in 2008 (3 years old). List prices for equipment manufactured in years other than 2008 have been adjusted to a 2008 price level using economic indexes. Ownership and operating expenses are computed using area factors, found in appendix B, which are specific to each region and volume. This hourly rate methodology assumes that equipment furnished to the job is in sound, workable condition. Furthermore, the methodology applies only to equipment that prime contractors or subcontractors either own or control. These hourly rates and cost factors do not represent rental charges for those in the business of renting equipment.

2.3 Total Hourly Rate. Hourly rates for average conditions are shown in table 2-1 and are computed based on a 40-hour (hr) workweek. The hourly rate is the sum of ownership and operating costs. Table 2-2 contains all individual rate elements for both average and severe conditions. An example of the methodology used to compute the total hourly rate is shown in figure 2-1. For standby calculation, see section IX.

a. Ownership Cost Elements. The ownership portion of the rate consists of an allowance for depreciation (DEPR) and facilities capital cost of money (FCCM).

b. Operating Cost Elements. Operating costs include allowances for the following:

Fuel. Filters, oil, and grease (FOG) (includes servicing). Repairs (includes maintenance and major overhauls). Tire wear (replacement). Tire repair.

c. Exclusions to Hourly Rates. Total hourly rates for owning and operating equipment do not include allowances for the following:

Operating labor.

EP 1110-1-8, Vol. 430 Nov 11

2-2

Mobilization and demobilization. Field office overhead expenses. Home office or general and administrative (G&A) overhead expenses. Investment tax credit. Contingency allowance. Profit. Parts and labor escalation.

It should also be noted that replacement cost is not included in the rates, as it is not an allowable item of cost per FAR 31.105(d)(2)(i).

d. Other Ownership Elements. The following elements of cost are not included in the total hourly rates. These costs are allowable and would normally be included in the contractor’s field office or home office overhead rate calculation.

(1) License fees, property taxes, storage, and insurance costs are considered indirect costs and are not included in the total hourly rates.

(2) Jobsite security, inspection fees, recordkeeping, mechanic training, and highway permits are also not included in the total hourly rates.

SECTION II. OPERATING CONDITIONS

2.4 Average, Difficult, or Severe Conditions. Operating conditions may be average, difficult, or severe. Hourly rates for both average and severe operating conditions are determined in accordance with appendix C. The rate for the difficult condition is the arithmetic mean of the average and the severe rates. When only the average rate is shown in table 2-2, the rate applies for all operating conditions or as determined by the contracting officer. Average condition rates are included in both tables 2-1 and 2-2. Only table 2-2 contains the severe condition rates.

2.5 Determination of Condition. For contract modifications, the contracting officer determines the equipment operating condition to be used. This determination is based on contract specifications, site conditions, basis of any supporting evidence, and guidance in appendix C. Evaluation of operating conditions for equipment not listed in appendix C will be consistent with examples shown in appendix C. The operating condition of the equipment relates to the average and severe factors as detailed in appendix D.

SECTION III. EQUIPMENT SELECTION

2.6 General. Equipment shown in table 2-1 is representative of equipment that is used in general construction. Note that some equipment may require additional attachments or accessories. Each unit of equipment is grouped into a main group called a category

EP 1110-1-8, Vol. 430 Nov 11

2-3

(CAT) and a subgroup called a subcategory (SUB). This type of grouping is displayed in table 2-1 and appendix D. Also, an identification number (ID No.) is assigned to each unit of equipment. The ID No. consists of three parts. The first three characters are the CAT, the second two characters are the manufacturer's code, and the last three characters are the sequence number.

2.7 Truck Selection. Because of the large number of possible combinations of highway truck chassis and bodies, both are listed separately. For estimating purposes, use the gross vehicle weight (GVW) rating of the truck chassis to make a selection with the following conditions:

a. The combined weight of the truck chassis, truck body, and payload must not exceed the GVW rating shown for the truck chassis.

b. The gross combined weight (GCW) of the truck, trailer, and payload must not exceed the GCW rating shown.

2.8 Crawler Tractor Selection. A wide range of combinations of ripper and various blade options are available for each crawler tractor. For ease of use, all tractors include a universal blade attachment. Other blade and ripper attachments are shown separately and should be substituted for the universal blade to match actual equipment configuration. Only the hourly expense for those attachments that are required to perform the work shall be allowed.

2.9 Equipment Accessories. Equipment accessories included on the major pieces of equipment in table 2-1 are listed in appendix J.

SECTION IV. EQUIPMENT VALUE

2.10 List Price and Accessories. The total list price includes those accessories normally purchased by the contractor plus required safety features.

2.11 Discount Code (DC). A 7.5-percent discount is used for all equipment except highway trucks that are discounted at 15 percent. The total discounted price is derived by subtracting the appropriate discount from the total list price. The identification of the discount is shown in appendix D under column heading DC. Two codes are used to identify the discount, B equals the basic discount of 7.5 percent and S equals the special discount of 15 percent.

2.12 Sales or Import Tax. Total state sales tax (which includes local taxes) or import tax is computed as a percentage of the discounted price. The average tax for the region is shown in appendix B.

EP 1110-1-8, Vol. 430 Nov 11

2-4

2.13 Freight. Estimated allowances for freight are provided in appendix B. This allowance includes preparation and delivery. Multiply the shipping weight based on hundredweight (cwt) by the freight rate to determine freight charges.

2.14 Total Equipment Value (TEV). Freight is added to the total discounted price (which includes sales tax) to arrive at the TEV. The estimated TEV is indicated in table 2-1 under the column heading VALUE.

SECTION V. LIFE

2.15 Economic Life (LIFE). The expected economic life of the equipment will vary based on the type of equipment and the condition of use. It is established from manufacturers’ or equipment associations’ recommendations. The expected economic life in hours is given in appendix D, under the column heading LIFE, for both average and severe conditions.

2.16 Working Hours Per Year (WHPY). Annual average operating hours have been established for equipment working within the region covered by this pamphlet. The number of WHPY as shown in appendix B is equivalent to 1 year’s use for a single shift operation. Average annual hours of use per year are determined by reducing the maximum available hours per year (40 hours per week, 52 weeks per year) to allow for lost working days due to the following factors:

• Weather. • Employee holidays. • Equipment maintenance and repairs. • Mobilization and demobilization. • Miscellaneous downtime.

SECTION VI. SALVAGE VALUE

2.17 Salvage Value (SLV). The salvage value for equipment is based on advertisements of used equipment for sale as displayed in current engineering and construction magazines, manufacturer’s recommendations, and the Green Guide Volumes I and II, Handbook of New and Used Construction Equipment Values, Equipment Watch.

2.18 Salvage Value Percentage. The salvage value percentage used for each type of equipment is listed in appendix D under the heading SLV as a percentage of the equipment value. It is equal for both average and severe conditions.

EP 1110-1-8, Vol. 430 Nov 11

2-5

SECTION VII. OWNERSHIP COST

2.19 Ownership Elements. The ownership portion of the rate consists of allowances for depreciation (DEPR) and facilities capital cost of money (FCCM). These two cost elements are computed based on the TEV. Other ownership elements may be allowed (see paragraph 2.3d.). Total ownership rate per hour is expressed by formula, as follows:

Ownership Rate/hr = DEPR/hr + FCCM/hr

2.20 Depreciation. The straight-line method is used to compute depreciation.

a. For rubber-tired equipment, the tire cost index (TCI) must first be calculated to complete the depreciation formula.

b. Hourly depreciation is calculated by dividing the “depreciable" value (TEV less estimated salvage and tire cost) by the expected economic life of the unit of equipment in hours. Expressed by formula, depreciation cost equals the following:

( )( )[ ] ( )( )[ ][ ]LIFE

Cost TireTCI - SLV-1TEV DEPR/hr =

Where: (1) TEV is the total equipment value found in table 2-1. (2) SLV is the salvage value from appendix D. (3) TCI is the tire cost index, which is determined by dividing the year of

manufacture tire index by the present-year tire index. For table 2-1, the present year is 2011 and the year of manufacture is 2008 (3 years old). These indexes are listed as part of appendix E [see Economic Key (EK) 100, All Tires and Tubes].

(4) Tire cost is the total tire and/or conveyor belt cost. The total tire cost is the sum of the cost of all front, drive, and trailing tires. The tire cost for rubber-tired equipment is based on tire values at the time the equipment was manufactured.

(5) The LIFE is the economic life, which is based on the number of operating hours throughout the economic life of the equipment (see paragraph 2.15). Hours for LIFE are provided in appendix D.

2.21 Facilities Capital Cost of Money (FCCM). The FCCM, as defined in FAR 31.205-10, is included in the total hourly rates. This cost is computed by multiplying a discounted cost of money rate (CMR) by the average value of equipment and prorating the result over the annual operating hours. The July 2011 CMR [2.50 percent as shown in appendix I determined by the Secretary of the Treasury pursuant to Public Law 92-41 (85 Stat. 97)] is discounted by a reduction of 25 percent to avoid duplication when applying estimated markups for overhead and profit. The discounted CMR is then 2.00 percent. The Department of the Treasury adjusts the CMR on or about 1 January and

EP 1110-1-8, Vol. 430 Nov 11

2-6

1 July each year; these revisions are printed in the Federal Register or can be found at http://www.treasurydirect.gov/govt/rates/tcir/tcir_opdprmt2.htm. The CMR should be adjusted to the actual period that the equipment is used. Expressed by formula, FCCM cost equals the following:

( )( )( )(WHPY)

CMR discountedAVFTEV FCCM/hr =

Where: a. TEV is the total equipment value found in table 2-1. b. ( )( )[ ][ ] 2N /2 SLV 11-N (AVF) Factor Value Average ++= . c. Number of Years (N) in Depreciation Period = LIFE/WHPY. d. LIFE is the economic life, which is based on the number of operating hours

throughout the economic life of the equipment (see paragraph 2.15). Hours for LIFE are provided in appendix D.

e. Discounted CMR = 2.50% (Jul – Dec 2011 rate) / 1.25 = 2.00%. f. WHPY = Working hours Per Year found in appendix B.

SECTION VIII. OPERATING COST

2.22 Operating Cost Elements. The total operating cost is the sum of the following five elements: fuel, FOG, repairs, tire wear, and tire repair.

2.23 Fuel Cost. Fuel costs are computed for each gas, diesel, or electric engine. When the unit of equipment has two engines, as in the case of a truck crane, this methodology treats each engine separately for fuel costs. The hourly fuel cost for each unit of equipment is shown under the column heading FUEL in tables 2-1 and 2-2. When the unit of equipment has no engine, no fuel cost will be shown. Hourly fuel costs are calculated for each engine, as expressed in the following formula:

Fuel Cost/hr = Horsepower (hp) x Fuel Cost/Gallon (gal) x Fuel Factor (gal/bhp-hr)

a. Horsepower is the engines rated horsepower. All horsepower ratings for engine-driven equipment are listed with the equipment description in table 2-1.

b. Fuel Cost/Gallon is based on values shown in appendix B. See chapter 3 for fuel cost adjustments.

c. Fuel Factor - Gas or Diesel Fuel. The fuel factor in gallons per brake horsepower-hour (bhp-hr) is listed in appendix D for both average and severe conditions. Fuel factors are also listed for both the engine powering the main equipment (prime engine) and the engine providing power to the carrier vehicle. For severe conditions, the fuel consumption rate is 30 percent greater than the average condition rate. Gas or diesel fuel factors are computed by using the following formula:

EP 1110-1-8, Vol. 430 Nov 11

2-7

Gal per Fuel of lbshr-bhp per Fuel lbs x (HPF) Factor Horsepower hr)-(Gal/bhp Factor Fuel

Where:

(1) The HPF is the horsepower factor used in the fuel and electricity consumption formulas and represents an average percent of full-rated horsepower being used by the engine. The fuel consumption factors, which are shown in appendix D under column headings Fuel Factor-Equipment and Fuel Factor-Carrier, are computed based on the HPF shown under these column headings. This HPF is an estimate of the engine load under average working conditions. It is necessary to modify the rated horsepower as engines and motors in actual production do not work at their full-rated horsepower at all times. Periods spent at idle, travel in reverse, traveling empty, close maneuvering at part throttle, and operating downhill are examples of conditions that reduce the HPF. Professional judgment regarding cycle time and equipment loading is applied to determine this average HPF. Normal field application can also vary according to: operator efficiency, type of material, type of work cycle, and overall jobsite efficiency. This pamphlet provides an estimated average HPF, not a specific factor.

(2) Pounds (lbs) fuel per bhp-hr is an average based on a variety of engine applications from manufacturer engine data. The following represent an average of the normal application of equipment and are indicative of engine fuel consumption industry wide. Pounds fuel (consumed) per bhp-hr is based on the following averages and is used consistently throughout this pamphlet:

Gasoline = 0.55 lbs per bhp-hr Diesel = 0.34 lbs per bhp-hr

(3) Pounds fuel per gallon is the factor that determines the weight of the fuel consumed. The following are used as constants in this pamphlet:

Gasoline = 6 lbs per gal Diesel = 7 lbs per gal

d. Fuel Factor - Electricity. Assuming that an electric motor uses 1 kilowatt (kW) per horsepower (considering all inefficiencies), and using the same HPF for gas or diesel fuel consumption, the electricity consumption is computed by the following formula:

hr-hpelectric per kW 1 x HPF (kW/hr) Factor Fuel

e. Fuel and Electricity Cost. The cost per gallon for gasoline and diesel fuel used to compute the hourly fuel cost is shown in appendix B. The hourly fuel cost for all gasoline-powered equipment, diesel-powered highway trucks, and truck crane carriers

EP 1110-1-8, Vol. 430 Nov 11

2-8

includes an allowance for Federal and state road taxes, sales taxes, and rental for fuel storage tanks and pumps. Cost per kilowatt-hour used to compute electricity cost are also shown in appendix B.

2.24 Filters, Oil, and Grease(FOG) Cost. The FOG cost is computed as a percentage of the hourly fuel costs.

a. The FOG contains items of cost for routine servicing of the equipment, which includes the following:

Base wages for servicing labor. Fringe benefits and labor burden costs for servicing. Service truck, tools, and fuel truck allowance. Shop allowance when shop servicing is required. Other equipment costs for servicing. FOG material allowance. Taxes and shipping for FOG supplies. Handling and disposal of hazardous materials and oil.

b. The hourly FOG cost is calculated for each engine using the following formula:

LAF x Cost/hr Fuel x Factor FOG Cost/hr FOG

Where: (1) The FOG Factor is the percent allowance expressed as a decimal factor

under each fuel type heading E (electricity), G (gas), or D (diesel). See appendix D. (2) Fuel cost/hr is a calculated value shown under the column heading FUEL in

tables 2-1 and 2-2. (3) The LAF (labor adjustment factor) is a decimal factor to account for regional

variations in labor and parts costs. This factor is provided in appendix B.

c. The FOG percentage allowance includes the cost for servicing. For equipment that is normally serviced by an oiler assigned to the unit of equipment, the FOG percentage is reduced. This reduction applies to the following equipment: cranes, draglines, hydraulic excavators, and shovels (except equipment under category numbers C75, C80.01, C85.11, C85.12, C85.21, C90.01, H25.11, H25.12, H30.01, H30.02, and M10.32).

d. When a unit of equipment has no engine (therefore no fuel costs calculated) and the equipment requires some type of fuel (i.e., propane, kerosene), an alternative hourly fuel and FOG allowance may be used in lieu of the regularly calculated fuel and FOG hourly costs. A FOG allowance may also be added when the equipment has no engine and has parts that require FOG. The alternative fuel allowance is added to the

EP 1110-1-8, Vol. 430 Nov 11

2-9

alternative FOG allowance for a total alternative fuel and FOG cost. (See figure 2-1, 5.c.)

2.25 Repair Cost.

a. The repair cost accounts for equipment repairs, maintenance, and major overhauls (including undercarriage wear, ground engaging tools, and designated attachments) performed in either the field or the shop. Where tire cost is the cost of the tires when the equipment was manufactured, use the same TCI and tire cost as shown in the depreciation calculation (see section 2-20). The estimated hourly rate for repairs is computed as follows:

LIFERF x Cost)]] e[(TCI)(Tir-[(TEV) Cost/hr Repair

Where: (1) TEV is the total equipment value found in table 2-1. (2) TCI is the tire cost index, which is determined by dividing the year of

manufacture tire index by the present-year tire index. For table 2-1, the present year is 2011 and the year of manufacture is 2008 (3 years old). These indexes are listed as part of appendix E [see Economic Key (EK) 100, All Tires and Tubes].

(3) Tire cost is the total tire and/or conveyor belt cost. The total tire cost is the sum of the cost of all front, drive, and trailing tires. The tire cost for rubber-tired equipment is based on tire values at the time the equipment was manufactured.

(4) Repair factor (RF) is calculated as follows:

LAF x EAF x RCF RF

Where: (a) The RCF (repair cost factor) is shown in appendix D. This factor varies

depending on the operating condition of the equipment (average or severe). (b) The EAF (economic adjustment factor) is used to adjust the RCF to

current price levels. The EAF is equal to the economic index for the present year divided by the economic index for the year of manufacture. Indexes listed in appendix E are used to develop the EAF. Economic indexes are determined as follows:

Economic Index for the Present Year. This is the economic index for the present year (2011 for table 2-1 calculations). Obtain the economic index from appendix E. The index is located in the column with the present year and the row with the type of equipment in question. When the column for the present year has not been included, the index can be estimated using a straight-line projection.

EP 1110-1-8, Vol. 430 Nov 11

2-10

Economic Index for the Year of Manufacture. This is the economic index for the year the equipment was manufactured (2008 for table 2-1 calculations). Obtain the economic index from appendix E. The index is located in the column with the year of manufacture and the row with the type of equipment in question. When the actual age of the equipment is beyond the last year of its economic life, the equipment is considered overage. Economic life is determined by dividing hours of LIFE (from appendix D) by WHPY (appendix B).

(5) The LIFE is the economic life, which is based on the number of operating hours throughout the economic life of the equipment (see paragraph 2.15). Hours for LIFE are provided in appendix D.

b. Items Included in the Repair Cost Factor. The estimated percentage allowances for the RCF are shown in appendix D under the column heading RCF and are expressed as decimal factors. These RCFs (for both the average and severe conditions) compensate for the following cost elements:

(1) Mechanic’s labor includes base wages, fringe benefits, supervision, travel, and all other costs for labor associated with craft workers engaged in the direct repair of equipment either in the field or the shop.

(2) Repair parts and supplies include those items that are required for all repairs and major overhauls complete with applicable sales taxes and freight charges.

(3) Service trucks and other equipment used during field or shop repair and maintenance work including tools.

(4) Supporting repair facilities include field and main repair shops, complete with parts and supplies inventory, and shop overhead.

2.26 Tire Wear Cost.

a. Tires included on rubber-tired equipment are generally the type and ply rating recommended as standard tires by the equipment manufacturer. Tire costs include both tire wear (replacement) and tire repair as individual elements of cost. Conveyor belt wear is also included under this cost element. The belt wear is treated like tire wear. The wear factors are listed in the front tire wear factor column in appendix D. Belt life and cost are listed in appendix F.

b. The formula for calculating tire wear applies to each tire position: front (FT), drive (DT), and trailing (TT). However, all tires performing the drive function are considered drive tires and are listed in the drive position. The total hourly tire wear cost for each unit of equipment is the sum of the hourly cost for each position. The total hourly tire

EP 1110-1-8, Vol. 430 Nov 11

2-11

wear cost equals the current cost of new tires plus the cost of one recapping divided by the expected life of the new tires plus the life of the recapped tires. This hourly allowance for determining tire wear cost is expressed in the following formula:

Life Tire Maximum x Factor WearTire x Factor Life TireCost Tire Current x Factor Cost Tire Cost/hr WearTire

Where: (1) Tire Cost Factor is estimated at 1.5, which represents the purchase of the

original tire plus one recap. It has been estimated that a recap costs approximately 50 percent of the new tire cost.

(2) Current Tire Cost is the estimated cost that applies to all tires on the equipment in that position. For example, four new drive tires valued at $500 each would result in an amount of $2,000 for total drive tire cost. The size and cost of each tire used in the pamphlet are listed for information in appendix F.

(3) Tire Life Factor is estimated at 1.8, which represents the original tire life plus one recap. It has been estimated that a recap lasts approximately 80 percent of the life of a new tire.

(4) Tire Wear Factor is based on the position of the tire, type of equipment, and condition of use. Tire wear factors have been developed and are listed in appendix D. These factors will provide a percentage reduction to the maximum tire life. Appendix G contains the methodology used to develop these factors and a computation example for a rear dump wagon.

(5) Maximum Tire Life expressed in hours is shown for various new tire types in appendix F. The tire life is estimated from information provided by Goodyear Tire and Rubber Company and by using the method and tables in Production and Cost Estimating of Material Movement with Earthmoving Equipment, Terex Corporation, Hudson, Ohio.

2.27 Tire Repair Cost. It has been estimated that tire repairs are 15 percent of the total hourly tire wear cost. The LAF is used to adjust the tire repair cost to account for regional variations in labor and parts costs. This cost element has been calculated and listed separately in table 2-2. It is expressed as a formula as follows:

LAF x 0.15 x Cost WearTireHourly Total Cost Repair Tire

SECTION IX. STANDBY HOURLY RATE

2.28 Standby Hourly Rate. The standby rate is computed by allowing the full FCCM hourly cost (based on a 40 hour workweek) plus one-half of the hourly depreciation. It is expressed as a formula, as follows:

FCCM/hr 0.50 x DEPR/hr Rate/hrStandby

EP 1110-1-8, Vol. 430 Nov 11

2-12

a. Paid standby shall not exceed 40 hours per week (7 calendar days) (based on a 40 hour workweek) per unit of equipment. Actual operating hours during a week will be credited against the 40 hours maximum standby allowance.

b. Standby costs will not be allowed during periods when the equipment would have otherwise been in idle status.

c. When the equipment is purchased used, standby will be computed on the basis that the equipment was purchased new by the contractor in the year it was actually manufactured. Refer to chapter 3 for rate adjustments.

SECTION X. RATE CALCULATION EXAMPLE

2.29 Computation Example. Figure 2-1 is an example of how the total hourly rates in table 2-1 are computed. A blank Equipment Rate Computation Worksheet is included in appendix A and can be copied as needed.

a. When an hourly rate for a specific unit of equipment is not included in this pamphlet and a rate must be computed, the methodology contained in chapter 2 shall be followed. However, when a unit of equipment is not included in this pamphlet and the necessary factors to compute a rate are not found in appendix D, please contact the Chief, Cost Engineering Branch, Engineering and Construction Division, Walla Walla District, U.S. Army Corps of Engineers, for assistance as explained in chapter 1. A Microsoft Excel® spreadsheet (CHECKRATE) is also available for rate computation (see chapter 1).

b. See chapter 3 for further guidance on the procedure for rate adjustments.

EP 1110-1-8, Vol. 430 Nov 11

1. EQUIPMENT INFORMATION AND EXPENSE FACTORS

a.(1)

(2) HC-238H II(3) 2011(4) 2008(5) 200(6) 445(7)

3 D-off

4 D-on(8) 1,913 cwt(9)

Size/Ply App F Code No. Unit Price Cost(a) Front (FT): 14-25/20 ANMB1 4 $1,928 $7,712(b) Drive (DT): 14-25/20 ANMB1 8 $1,928 $15,424(c) 0 $0 $0(d) $23,136

(10)$1,578,897 $0

b. 0.04c.

(1) 20(2) A AVERAGE(3) B 0.075(4) 20,000(5) 0.20(6) 0.024(7) 0.005(8) 0.110(9)

(a) 0.66(b) 0.58(c) 0.73

(10) 0.90

Horsepower - Equipment:

Present Year or Year of Use:Year Manufactured:

Equipment Specification Data:Equipment Description:

Model and Series:

CRANES, MECHANICAL, LATTICE BOOM, TRUCK MTD, 150 TON / 260' BOOM, 8X4

Horsepower - Carrier:

Shipping Weight (cwt):

- Equipment: 0-None; 1-electric; 2-gasoline;3-diesel off-road; 4-diesel on-road; 5-marine gas;6-marine diesel

- Carrier: 0-None; 1-electric; 2-gasoline; 3-diesel off-road; 4-diesel on-road; 5-marine gas;6-marine diesel

Fuel

Tire size and number of tires: (Cost of tires based on present year, see 1.a.(3) and App. F):

Enter number from 0 to 6 ==>


Category and Subcategory Number:USE APPENDIX D TO COMPLETE THE FOLLOWING DATA:

List Price + Accessories: [at Year (yr) of Manufacture]

Hourly Expense Calculation Factors:C90

Trailing (TT):

Life in Hours (LIFE):Salvage Value Percentage (SLV):

Total Tire Cost:

Fuel Factor - Carrier (E G D):

Condition (C): A=Average D=Difficult S=Severe

Filter, Oil, and Grease (FOG) Factor (E G D):

Economic Key (EK):

Discount Code (DC): B = 7.5% (0.075) or S = 15.0% (0.15)

Fuel Factor - Equipment [Electric (E) Gas (G) Diesel (D)]:

OR actual purchase price:

Tire Wear Factor:

Repair Cost Factor (RCF):

Front (FT):Drive (DT):Trailing (TT):

Use this worksheet to compute an hourly rate for equipment that is not in this pamphlet or is in the pamphlet but not equivalent in size, capacity, horsepower, or value (see appendix A for blank form).

Region 04

ID No: C90LB001

Example: The piece of equipment shown in this example is based on a known piece of equipment for illustration purposes only.

Figure 2-1. Equipment Rate Computation Worksheet Page 1 of 6

EP 1110-1-8, Vol. 430 Nov 11

2-13

2.

a. = $1,578,897

(1) Discount: (List Price + Accessories) x {1.a.(10)} {1.c.(3)}

($1,578,897 + $0.00) x 0.075 = -($118,417)

(2) $1,460,480

(3) Sales or Import Tax: Subtotal x Tax Rate {2.a.(2)} {'Appendix B}

$1,460,480 x 5.55% = $81,057

(4) $1,541,537

b. x{1.a.(8)} {Appendix B}

1,913 cwt x $4.97 /cwt = $9,508

c. TOTAL [2.]: = $1,551,045

3.

a. LIFE / {1.c.(4)} {Appendix B}

20,000 hr / 1,260 hr/yr = 15.87 yrs (N)

4.

a.

(1) Tire Cost Index (TCI):

Tire Index, Year of Manufacture,

{1.a.(4)} / =Tire Cost

Index (TCI) Appendix E, EK=100

3267 / 3735 = 0.875

(2) [TEV x (1.0-SLV) - (TCI x Tire Cost)] / LIFE{2.c.} {1.c.(5)} {4.a.(1)} {1.a.(9)(d)} {1.c.(4)}

[$1,551,045 x (1.0-0.20) - ( 0.875 x $23,136 )] / 20,000 hrs = $61.03 /hr

Depreciation

(See chapter 3 for used and overage equipment rate adjustments.)

Subtotal =

Appendix E, EK=100

Working Hours Per Year (WHPY) = N

Shipping WeightFreight Rate per

cwt

TOTAL EQUIPMENT VALUE (TEV):

Tire Index, Present Year or Year of Use, {1.a.(3)}

DEPRECIATION PERIOD (N)

OWNERSHIP COST

{2.a.(4)} + {2.b} OR actual purchase price {1a.(10)}

Region 04

Freight:

EQUIPMENT VALUE


Discount Code

Subtotal {2.a.} - {2.a.(1)}

Total Discounted Price: Subtotal: 2.a.(2) + 2.a.(3)

Subtotal =


EP 1110-1-8, Vol. 430 Nov 11

2-14

4. OWNERSHIP COST (Continued)

b. Facilities Capital Cost of Money (FCCM):

(1) [( N - 1.0 ) x (1.0 + SLV) + 2.0] / (2.0 x N) =Avg Value

Factor{3.a.} {1.c.5.} {3.a.} (AVF)

[(15.87 yr - 1.0) x (1.0 + 0.20) + 2.0] / (2.0 x 15.87 yr) = 0.625

(2) TEV x AVF xAdjusted

Cost-of-Money / WHPY

{2.c.} {4.b.(1)} {Appendix B} {Appendix B}

$1,551,045 x 0.625 x 2.00% / 1,260 hr/yr = $15.39 /hr

c. TOTAL HOURLY OWNERSHIP COST: TOTAL [4.]: = $76.42 /hr

{4.a.(2)} + {4.b.(2)}

5. OPERATING COST

a. Fuel Costs:

(1) Equipment:

Fuel Factor x Horsepower (hp) xFuel Cost per Gallon (gal)

{1.c.(6)} {1.a.(5)} {Appendix B}

0.024 x 200 hp x $3.40 /gal = $16.32 /hr

(2) Carrier:{ 1.c.(4)}

Fuel Factor x Horse power (hp) x Fuel Cost per gal{1.c.(7)} {1.a.(6)} {Appendix B}

0.005 x 445 hp x $3.90 /gal = $8.68 /hr

(3) Total Hourly Fuel Cost: Total [5.a.] = $25.00 /hr{5.a (1)} + {5.a (2)}

b. FOG Cost:

(1) Equipment:

FOG Factor xEquipment Hourly

Fuel Cost xLabor Adjustment

Factor (LAF){1.c.(8)} {5.a.(1)} {Appendix B}

0.110 x $16.32 /hr x $ 1.04 /hr = $1.87 /hr

Region 04


EP 1110-1-8, Vol. 430 Nov 11

2-15

5.

(2) Carrier:

FOG Factor xCarrier Hourly

Fuel Cost x LAF {1.c.(8)} {5.a.(2)} {Appendix B}

0.110 x $8.68 /hr x 1.04 = $0.99 /hr

(3) Total [5.b.] = $2.86 /hr

c. Total [5.c.] = $0.00 hr

d.

(1)EK is from {1c. (1)}

/

6982 / 6685 = 1.044

(2) Repair Factor (RF):

RCF x EAF x LAF{1.c.(10)} {5.d.(1)} {Appendix B}

0.90 x 1.044 x 1.04 = 0.977

(3) Repair Cost:

[TEV - (TCI x Tire Cost)] x RF / LIFE {2.c.} {4.a.(1)} {1.a.(9)(d)} {5.d.(2)} {1.c.(4)}

[$1,551,045 - (0.875 x $23,136)] x 0.977 / 20,000

(4) Total [5.d.] = $74.78 /hrTotal Hourly Repair Cost:

Appendix E, EK={1.c.(1)} Appendix E, EK={1.c.(1)}

OPERATING COST (Continued)

Region 04

Total Hourly FOG Cost:

Alternative Fuel/FOG Cost:

{5.b.(1)} + {5.b.(2)}

(See chapter 2, paragraph 2.24.d. for guidance on when to use.)

Repair Cost:

Economic Index, Present Year or Year of Use,{1.a.(3)}

Economic Index, Year of Manufacture, {1.a.(4)}

Economic Adjustment Factor (EAF):

(See table 3-1 for last year of economic life.)


EP 1110-1-8, Vol. 430 Nov 11

2-16

5.

e.

(1) Front Tires (FT):

(1.5 x FT Cost) / (1.8 x FT Wear Factor x Maximum Tire Life Hours){1.a.(9)(a)} {1.c.(9)(a)} {Appendix F}

(1.5 x $7,712) / (1.8 x 0.66 x 2,500 hr) = $3.89 /hr

(2) Drive Tires (DT):

(1.5 x DT Cost) / (1.8 x DT Wear Factor x Maximum Tire Life Hours){1.a.(9)(b)} {1.c.(9)(b)} {Appendix F}

(1.5 x $15,424) / (1.8 x 0.58 x 2,500 hr) = $8.86 /hr

(3) Trailing Tires (TT):

(1.5 x TT Cost) / (1.8 x TT Wear Factor x Maximum Tire Life Hours){1.a.(9)(c)} {1.c.(9)(c)} {Appendix F}

(1.5 x $0.00) / (1.8 x 0.73 x 0 hr) = $0.00 /hr

(4) Total Tire Wear Cost: Total [5.e.] = $12.75 /hr

f.

Total Tire Wear Cost per Hour x (0.15 x LAF)

{5.e.(4)} {Appendix B}

$12.75 /hr x (0.15 x 1.04) Total [5.f.] = $1.99 /hr

g. Total [5.] = $117.38 /hrTOTAL HOURLY OPERATING COST:

Sum {5.e.(1)} through {5.e.(3)}

Sum {5.a.} through{ 5.f.}

Region 04


Tire Repair Cost:

Tire Wear Cost: (Use current price levels. See Appendix F.)


EP 1110-1-8, Vol. 430 Nov 11

2-17

6.

a.

+ Operating Cost{4.c.} {5.g.}

$76.42 /hr + $117.38 /hr = $193.80 /hr

b.

Depreciation + (FCCM x 40 hr/wk / Work hr/wk) + Operating Cost

{4.a.(2)} {4.b.(2)} {5.g.}

$61.03 /hr + ($15.39 /hr x 40 hr/wk / 60 hr/wk) + $117.38 /hr = $188.67 /hr

c.

(Depreciation x 0.50) + FCCM {4.a.(2)} {4.b.(2)}

($61.03 /hr x 0.50) + $15.39 /hr = $45.91 /hr

Standby Hourly Rate:

(Refer to Chapter 2, paragraph 2.28 for guidance on use.)

See Chapter 3 if rate adjustments are necessary.

(Refer to Chapter 3, paragraph 3.12 for guidance for overage equipment.)

Region 04

Other Work Shifts Hourly Rate:

example:60 hr/wk

(example:60 hr/wk)

HOURLY RATES

Total Hourly Rate: [based on 40 hours per week (wk)]

(Refer to Chapter 3, Adjustments to Rates, for methodology.)

Ownership Cost


EP 1110-1-8, Vol. 430 Nov 11

2-18

2-21

Table 2-1. Hourly Equipment Ownership and Operating Expense

EXPLANATION OF TABLE HEADINGS

Example unit of equipment: Link Belt, Model HC-238H II, 150 Ton, 260’-boom.

CAT: C90 is the category number and identifies it as Cranes, Mechanical, Lattice Boom, Truck Mounted (from appendix D). ID No.: C90LB001 is the unique identification number for the above Link Belt crane. AM equals the manufacturer (see appendix H). 001 equals the numeric order of this unit of equipment within the manufacturer’s listing. MODEL: HC-238H II is the equipment model number. EQUIPMENT DESCRIPTION: Specific information for each particular unit of equipment is described, such as “150 ton with a 260-foot boom” for the Link Belt crane. ENGINE HORSEPOWER AND FUEL TYPE: The amount of horsepower and type of fuel used is stated for the main and carrier engines. The Link Belt crane carrier has a 445-horsepower engine, and the crane has a 200-horsepower engine. Both engines are diesel (D). VALUE (TEV): This column reflects the predetermined “equipment cost” used to compute the rates and is based on equipment purchased new in 2008. TOTAL HOURLY RATES ($/HR): All ownership and operating expenses for the average condition are included. All cost elements, including fuel, are totaled in the AVERAGE column. The STANDBY column includes the hourly allowance for equipment on legitimate standby status (see section 2.27 for more information). ADJUSTABLE ELEMENTS: This column shows ownership elements and fuel costs used to develop the average total hourly rates so they can be adjusted as indicated in chapter 3. Operating costs may be determined by subtracting the ownership cost elements (DEPR plus FCCM) from the total hourly rate for the average condition. CWT: The shipping weight of the equipment is stated in hundredweight.

EP 1110-1-8, Vol. 430 Nov 11

2-19

TOTAL HOURLY RATES ($/HR)

VALUE (TEV)

2008 ($)MODEL EQUIPMENT DESCRIPTION MAIN

ENGINE HORSEPOWER AND FUEL TYPE

AVERAGE STANDBY DEPR FCCM FUEL CWTID.NO. CARRIER

ADJUSTABLE ELEMENTS

Table 2-1. HOURLY EQUIPMENT OWNERSHIP AND OPERATING EXPENSE4REGION

EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

AGGREGATE / CHIP SPREADERSA100.10 SELF-PROPELLEDSUBCATEGORY

ROSCO, A LeeBoy COMPANY

152SPRHA10RS003 $117,223 11.47 1.23 17.57 1496.9744.48CHIP SPREADER, SELF PROPELLED, 10' WIDE, 1.70 CY, 2WD

HP D-off


HP D-off


HP D-off


HP D-off


HP D-off

205SPREADPROA10RS008 $232,021 22.82 2.44 23.70 15813.8575.71CHIP SPREADER, SELF PROPELLED, 16' WIDE, 4.50 CY, 4WD

HP D-off

0.20 TOWED & TAILGATESUBCATEGORY

AMERICAN ROAD MACHINERY, INC.

TG-505CA10AR001 $3,271 0.44 0.04 0.00 50.260.84CHIP SPREADER, TAILGATE, 8' WIDE (ADD DUMP TRUCK)

ODELL 900A10AR002 $15,862 2.11 0.17 0.00 221.234.20CHIP SPREADER, TOWED, 8' WIDE, 3 CY (ADD DUMP TRUCK)

SEALMASTER, INC.

R-1 E2310A10SE001 $13,664 1.82 0.15 0.00 211.063.45CHIP SPREADER, TAILGATE, 8' WIDE, 1.13 CY (ADD DUMP TRUCK)

EP 1110-1-8, Vol. 430 Nov 11

2-20


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

A10 SEALMASTER, INC. (continued)R-1 E2500A10SE002 $16,047 2.14 0.17 0.00 301.244.05CHIP SPREADER, TOWED, 8' WIDE, 1.13

CY (ADD DUMP TRUCK)

AIR COMPRESSORS, PORTABLEA150.10 ROTARY SCREWSUBCATEGORY

INGERSOLL RAND ROTARY-REC COMPRESSOR DIV

56P185WJDA15IA001 $18,850 1.48 0.19 6.85 210.9311.10AIR COMPRESSOR, 175 CFM, 100 PSI (ADD HOSE)

HP D-off

110HP375WJDA15IA002 $42,747 3.39 0.44 13.46 382.1422.79AIR COMPRESSOR, 300 CFM, 150 PSI (ADD HOSE)

HP D-off

174VHP400WJDA15IA003 $55,188 4.36 0.57 21.30 532.7533.86AIR COMPRESSOR, 400 CFM, 200 PSI (ADD HOSE)

HP D-off

174HP450WJDA15IA004 $55,368 4.37 0.57 21.30 532.7633.89AIR COMPRESSOR, 450 CFM, 150 PSI (ADD HOSE)

HP D-off

174XP525WCUA15IA005 $62,952 4.98 0.65 21.30 533.1435.25AIR COMPRESSOR, 525 CFM, 125 PSI (ADD HOSE)

HP D-off

300XHP650WCATA15IA006 $139,068 11.01 1.43 36.72 1366.9466.23AIR COMPRESSOR, 650 CFM, 350 PSI (ADD HOSE)

HP D-off

300XHP750WCATA15IA007 $147,078 11.65 1.52 36.72 1367.3567.67AIR COMPRESSOR, 750 CFM, 300 PSI (ADD HOSE)

HP D-off

335VHP825WCUA15IA008 $110,135 8.70 1.14 41.00 965.4965.89AIR COMPRESSOR, 825 CFM, 200 PSI (ADD HOSE)

HP D-off

310XP1000WCUA15IA009 $99,717 7.87 1.03 37.94 1044.9760.59AIR COMPRESSOR, 1,000 CFM, 125 PSI (ADD HOSE)

HP D-off

400XHP1070WCATA15IA010 $204,755 16.27 2.11 48.96 15210.2591.73AIR COMPRESSOR, 1,070 CFM, 350 PSI (ADD HOSE)

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-21


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

SULLAIR CORPORATION

76125DPQJDA15SR006 $12,034 0.93 0.12 9.30 240.5912.63AIR COMPRESSOR, 125 CFM, 100 PSI (ADD HOSE)

HP D-off


HP D-off

78185A15SR004 $12,034 0.93 0.12 9.55 240.5912.91AIR COMPRESSOR, 185 CFM, 100 PSI (ADD HOSE)

HP D-off

80260A15SR005 $16,114 1.26 0.17 9.79 260.8013.92AIR COMPRESSOR, 260 CFM, 100 PSI (ADD HOSE)

HP D-off

123375HDPQJDA15SR008 $27,464 2.14 0.28 15.06 421.3521.89AIR COMPRESSOR, 375 CFM, 150 PSI (ADD HOSE)

HP D-off


HP D-off

230600HDTQCAA15SR010 $59,086 4.62 0.61 28.15 1002.9242.32AIR COMPRESSOR, 600 CFM, 150 PSI (ADD HOSE)

HP D-off

300750HHDTQCAA15SR011 $69,444 5.44 0.72 36.72 1033.4453.80AIR COMPRESSOR, 750 CFM, 175 PSI (ADD HOSE)

HP D-off

440900XHA15SR002 $141,102 11.12 1.46 53.86 1577.0285.93AIR COMPRESSOR, 900 CFM, 350 PSI (ADD HOSE)

HP D-off

3001050DTQCAA15SR012 $68,385 5.36 0.71 36.72 1053.3953.62AIR COMPRESSOR, 1,050 CFM, 100 PSI (ADD HOSE)

HP D-off

4501300HDTQCAA15SR013 $120,962 9.57 1.25 55.08 1566.0483.64AIR COMPRESSOR, 1,300 CFM, 150 PSI (ADD HOSE)

HP D-off

4501600HDTQCAA15SR014 $132,358 10.35 1.37 55.08 1626.5585.83AIR COMPRESSOR, 1,600 CFM, 100 PSI (ADD HOSE)

HP D-off

NO SPECIFIC MANUFACTURER

3085GA15XX019 $10,377 0.80 0.11 7.36 140.5110.29AIR COMPRESSOR, 85 CFM, 100 PSI (ADD HOSE)

HP G

EP 1110-1-8, Vol. 430 Nov 11

2-22


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

A15 NO SPECIFIC MANUFACTURER (continued)3085DA15XX020 $19,829 1.55 0.20 3.67 240.987.68AIR COMPRESSOR, 85 CFM, 100 PSI (ADD

HOSE) HP D-off


HP G

35100DA15XX022 $20,294 1.59 0.21 4.28 171.018.47AIR COMPRESSOR, 100 CFM, 125 PSI (ADD HOSE)

HP D-off


HP G

50130A15XX024 $22,845 1.80 0.24 6.12 181.1411.00AIR COMPRESSOR, 130 CFM, 100 PSI (ADD HOSE)

HP D-off


HP G


HP D-off


HP G


HP D-off


HP G


HP D-off


HP D-off


HP D-off


HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-23


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

A15 NO SPECIFIC MANUFACTURER (continued)250600A15XX034 $85,469 6.73 0.88 30.60 994.2549.79AIR COMPRESSOR, 600 CFM, 150 PSI

(ADD HOSE) HP D-off


HP D-off


HP D-off


HP D-off

3601200A15XX038 $159,010 12.61 1.64 44.06 1507.9578.05AIR COMPRESSOR, 1,200 CFM, 125 PSI (ADD HOSE)

HP D-off


HP D-off


HP D-off

0.20 SHOP TYPESUBCATEGORY


580/15A15XX041 $2,588 0.18 0.03 0.30 30.120.83AIR COMPRESSOR, 22 CFM, 80 GAL (ADD HOSE)

HP E


HP E


HP E


HP E


HP E

EP 1110-1-8, Vol. 430 Nov 11

2-24


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

A15 NO SPECIFIC MANUFACTURER (continued)30120/112A15XX046 $10,738 0.76 0.11 1.82 50.494.28AIR COMPRESSOR, 103 CFM, 120 GAL

(ADD HOSE) HP E

AIR HOSE, TOOLS & EQUIPMENTA200.10 AIR DRILL HOSESUBCATEGORY


A20XX001 $1,440 0.39 0.02 0.00 10.221.14AIR HOSE, 0.75", 100', HARDROCK A20XX002 $1,668 0.45 0.02 0.00 10.251.31AIR HOSE, 1.00", 100', HARDROCK A20XX003 $2,076 0.56 0.02 0.00 10.301.63AIR HOSE, 1.25", 100', HARDROCK A20XX004 $2,707 0.73 0.03 0.00 10.402.13AIR HOSE, 1.50", 100', HARDROCK A20XX005 $3,834 1.04 0.04 0.00 20.563.02AIR HOSE, 2.00", 100', HARDROCK A20XX006 $4,700 1.28 0.05 0.00 30.693.70AIR HOSE, 2.50", 100', HARDROCK A20XX007 $5,805 1.58 0.06 0.00 40.854.57AIR HOSE, 3.00", 100', HARDROCK A20XX008 $7,757 2.11 0.09 0.00 61.156.12AIR HOSE, 4.00", 100', HARDROCK

0.20 SANDBLAST HOSESUBCATEGORY

CLEMCO INDUSTRIES CORPORATION

A20CM017 $392 0.11 0.00 0.00 10.060.33SANDBLAST HOSE, 0.75"ID, 100' LONG USE AS SAND BLASTING ACCESSORY


EP 1110-1-8, Vol. 430 Nov 11

2-25


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

A20 CLEMCO INDUSTRIES CORPORATION (continued)



0.30 SANDBLASTERS, BREAKERS, & MISC. AIR TOOLSSUBCATEGORY

CHICAGO PNEUMATIC TOOL CO.

20CP-0009AA20CK002 $916 0.14 0.01 0.00 10.080.42ROTARY / CHIP HAMMER, 8 LB, AIR (ADD 30 CFM COMPRESSOR & BIT COSTS)

CFM A

32CP-0014RRA20CK001 $1,588 0.24 0.02 0.00 10.140.73ROTARY / CHIP HAMMER, 15 LB, AIR (ADD 30 CFM COMPRESSOR & BIT COSTS)

CFM A

56CP-0022A20CK003 $1,780 0.27 0.02 0.00 10.160.81ROCK DRILL, 30 LB, AIR (ADD 50 CFM COMPRESSOR & BIT COSTS)

CFM A

130CP-0069A20CK005 $2,251 0.34 0.02 0.00 10.191.02ROCK DRILL, 55 LB, AIR (ADD 140 CFM COMPRESSOR & BIT COSTS)

CFM A

45CP-0111-CHLAA20CK006 $1,117 0.17 0.01 0.00 10.100.51BREAKER-FOUR BOLT, 25 LB (ADD 50 CFM COMPRESSOR & BIT COSTS)

CFM A

63CP-1230-SA20CK008 $1,252 0.19 0.01 0.00 10.110.57BREAKER-FOUR BOLT, 60 LB (ADD 65 CFM COMPRESSOR & BIT COSTS)

CFM A

81CP-1240-SA20CK010 $1,357 0.20 0.01 0.00 10.110.61BREAKER-FOUR BOLT, 90 LB (ADD 90 CFM COMPRESSOR & BIT COSTS)

CFM A

EP 1110-1-8, Vol. 430 Nov 11

2-26


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

CLEMCO INDUSTRIES CORPORATION

100PACKAGE TWOA20CM010 $4,266 0.64 0.04 0.00 40.362.00SANDBLASTER, 2 CF CAP, W/0.50" D X 25'L HOSE (ADD 100 CFM COMPRESSOR & NOZZLE COST)

CFM A

170PACKAGE FOUR

A20CM011 $5,494 0.82 0.06 0.00 50.472.56SANDBLASTER, 4 CF CAP, W/1.00"D X 25'L HOSE (ADD 170 CFM COMPRESSOR & NOZZLE COST)

CFM A

200PACKAGE SIXA20CM012 $6,169 0.93 0.06 0.00 60.532.94SANDBLASTER, 6 CF CAP, W/1.25"D X 25'L HOSE (ADD 200 CFM COMPRESSOR & NOZZLE COST)

CFM A

450A20CM013 $18,785 2.72 0.19 0.00 301.558.67SANDBLASTER, 60 CF CAP, W/1.25"D X 50'L HOSE (ADD 450 CFM COMPRESSOR & NOZZLE COST)

CFM A


CFM A


CFM A

A20CM016 $16,120 2.42 0.17 0.00 691.387.64SANDBLAST ABRASIVE STORAGE HOPPER, 700 CF, 8' DEEP,10' WIDE & 23' HIGH (ADD SAND BLASTER & ACCESSORIES)

WACKER CORPORATION

2EHB11/BL/110A20WC002 $1,219 0.18 0.01 0.11 10.100.85BREAKER/DRILL, 40 LB, ELECTRIC (ADD 2 KW GENERATOR & BIT COSTS)

HP E

4BH 23A20WC004 $3,538 0.53 0.04 0.85 10.312.58BREAKER/DRIVER, 65 LB, W/POWER UNIT (ADD BIT COSTS)

HP G

EP 1110-1-8, Vol. 430 Nov 11

2-27


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)


100STANDARD 25-30 LBS

A20XX021 $1,335 0.20 0.01 0.00 10.110.60PAVEMENT BREAKER, 25-30 LB, HAND HELD (ADD 100 CFM COMPRESSOR & BIT COSTS)

CFM A

100SILENCED 35-45 LBS


CFM A



CFM A



CFM A

10055DRYA20XX025 $2,731 0.41 0.03 0.00 10.241.24ROCK DRILL, DRY, 55 LB, HAND HELD (ADD 100 CFM COMPRESSOR & BIT COSTS)

CFM A

ASPHALT PAVING DISTRIBUTORSA250.00 ASPHALT PAVING DISTRIBUTORSSUBCATEGORY


MAXIMIZER 11A25RS006 $64,405 9.66 0.66 0.00 705.4921.40ASPHALT DISTRIBUTOR, 1,900 GAL, 400 GPM, TRUCK MTD (ADD 32,000 GVW TRUCK)

MAXIMIZER 11A25RS008 $73,821 11.07 0.76 0.00 976.3025.00ASPHALT DISTRIBUTOR, 3,000 GAL, 400 GPM, TRUCK MTD (ADD 42,000 GVW TRUCK)

EP 1110-1-8, Vol. 430 Nov 11

2-28


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT


1100GA25XX001 $54,377 8.16 0.56 0.00 644.6417.73ASPHALT DISTRIBUTOR, 1,100 GAL, 400 GPM, TRUCK MTD (ADD 32,000 GVW TRUCK)



ASPHALT PAVERS & MISCELLANEOUS ROAD EQUIPMENTA300.10 SELF PROPELLEDSUBCATEGORY

BARBER-GREENE COMPANY

224BG2455DA30BG005 $395,596 42.03 4.03 25.89 37425.05130.40ASPHALT FINISHER, 10' WIDE SCREED, CRAWLER, W/19' 6" SCREED EXTENSION, 215 CF HOPPER

HP D-off

224BG260DA30BG003 $378,398 37.56 3.86 25.89 38222.64126.03ASPHALT FINISHER, 10' WIDE SCREED, WHEEL, W/19' 6" SCREED EXTENSION, 215 CF HOPPER

HP D-off

BLAW KNOX CONSTRUCTION EQUIPMENT CORP.

107PF-161A30BK011 $261,383 26.31 2.66 12.37 21015.8280.55ASPHALT PAVER/FINISHER, 8' WIDE SCREED, WHEEL, 181 CF HOPPER

HP D-off


HP D-off


HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-29


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

A30 BLAW KNOX CONSTRUCTION EQUIPMENT CORP. (continued)

184PF-6110A30BK018 $395,519 42.02 4.03 21.27 40025.04123.69ASPHALT PAVER/FINISHER, 10' WIDE SCREED, CRAWLER, 218 CF HOPPER

HP D-off

105RW 100 AA30BK019 $279,481 29.48 2.85 12.14 24517.5984.15ASPHALT PAVER, SHOULDER PAVING MACHINE, 1'-10' WIDE, BITUMINOUS & AGGREGATE, WHEEL, 72.5 CF HOPPER

HP D-off

173RW 195A30BK020 $365,824 38.65 3.73 20.00 33023.06114.85ASPHALT PAVER, SHOULDER PAVING MACHINE, 2'-10' WIDE, BITUMINOUS & AGGREGATE, WHEEL, 73 CF HOPPER

HP D-off

176TITAN 325 EPMA30BK021 $384,887 40.89 3.92 20.35 39924.37119.97ASPHALT PAVER, 32.8' WIDE, CRAWLER W/DUAL TAMPER SCREED, 270 CF HOPPER

HP D-off

145PF-2181A30BK022 $294,465 30.08 3.00 16.76 28318.0493.33ASPHALT PAVER, 8' WIDE SCREED, WHEEL, 2 WHEEL DRIVE, 182 CF HOPPER

HP D-off

145PF-4410A30BK023 $337,026 35.81 3.43 16.76 26921.34103.86ASPHALT PAVER, 8' WIDE SCREED, CRAWLER, 155 CF HOPPER

HP D-off

CATERPILLAR INC. ( MACHINE DIVISION)

174AP-655DA30CA013 $266,897 28.36 2.72 20.11 40216.9089.93ASPHALT PAVER, 8' WIDE SCREED, CRAWLER, 177 CF HOPPER

HP D-off

174AP-600DA30CA002 $277,912 28.26 2.83 20.11 31916.9692.94ASPHALT PAVER, 8' WIDE+2' EXT. PAVEMASTER SCREED, WHEEL, 230 CF HOPPER

HP D-off

153AP-900BA30CA014 $322,484 32.73 3.29 17.69 37819.66101.71ASPHALT PAVER, 10' WIDE SCREED, WHEEL, 215 CF HOPPER

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-30


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

A30 CATERPILLAR INC. ( MACHINE DIVISION) (continued)

224AP-1000DA30CA008 $321,893 32.77 3.28 25.89 46819.67110.81ASPHALT PAVER, 10' - 12' WIDE PAVEMASTER SCREED, WHEEL, 215 CF HOPPER

HP D-off

174AP-1050BA30CA015 $517,839 55.02 5.28 20.11 41532.79153.25ASPHALT PAVER, 10' WIDE EXTEND-A-MAT SCREED, CRAWLER, 215 CF HOPPER

HP D-off

173AP-1055DA30CA016 $433,143 46.02 4.41 20.00 41327.42131.75ASPHALT PAVER, 10' WIDE SCREED, CRAWLER, 215 CF HOPPER

HP D-off

173AP-1050BA30CA009 $437,936 46.53 4.46 20.00 41827.73132.96ASPHALT PAVER, 10' - 24' WIDE PAVEMASTER SCREED, CRAWLER, 215 CF HOPPER

HP D-off

CHAMPION ROAD MACHINERY-PRO PAV (WIRTGEN

110780WBA30CH001 $285,033 28.82 2.90 12.72 26517.3186.90ASPHALT PAVER, 8' WIDE SCREED, WHEEL, 190 CF HOPPER

HP D-off


HP D-off

152880RTBA30CH003 $313,010 33.26 3.19 17.57 28219.8298.72ASPHALT PAVER, 8' WIDE SCREED, CRAWLER-RUBBER TRACK, 190 CF HOPPER

HP D-off


HP D-off


HP D-off

2001110RTB SWIFTRACK

A30CH006 $416,728 44.28 4.25 23.12 40226.39131.13ASPHALT PAVER, 10' WIDE SCREED, CRAWLER-RUBBER TRACK, 225 CF HOPPER

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-31


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

GEHL COMPANY

251448A30GC002 $41,062 4.26 0.42 2.89 672.5513.65ASPHALT PAVER, 8' WIDE SCREED, WHEEL, 80 CF HOPPER

HP D-off

411648A30GC004 $59,077 6.28 0.60 4.74 853.7420.24ASPHALT PAVER, 9' WIDE SCREED, CRAWLER, 120 CF HOPPER

HP D-off

0.20 TOWEDSUBCATEGORY

MIDLAND MACHINERY CO

80SP-8A30MP001 $170,400 13.63 1.76 8.43 1858.5839.67ASPHALT PAVER, SHOULDER PAVING MACHINE, 1'-8' WIDE, BITUMINOUS & AGGREGATE, WHEEL, 80 CF HOPPER

HP D-off

100SP-10A30MP002 $191,094 15.29 1.97 10.54 2759.6245.71ASPHALT PAVER, SHOULDER PAVING MACHINE, 1'-10' WIDE, BITUMINOUS & AGGREGATE, WHEEL, 80 CF HOPPER

HP D-off

0.30 SLURRY SEAL PAVERS (Cold mix)SUBCATEGORY


110MINIMACA30XX001 $156,151 10.16 1.59 10.85 1306.6732.55ASPHALT PAVER, SLURRY SEAL PAVER 8' WIDE, SELF PROPELLED, WHEEL, 80 CF HOPPER

HP D-off

110MACROPAVER 12B

A30XX002 $190,991 12.73 1.95 10.85 1758.3236.18ASPHALT PAVER, SLURRY SEAL PAVER 8' WIDE, TRUCK MTD, 12 CF HOPPER (ADD 40,000 GVW TRUCK)

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-32


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

0.40 MISCELLANEOUS ROAD EQUIPMENTSUBCATEGORY

BLAW KNOX CONSTRUCTION EQUIPMENT CORP.

184MC-330A30BK024 $374,049 29.12 3.86 19.39 43018.4288.64ASPHALT PAVER, MOBILE CONVEYOR, 60" WIDE BELT, WHEEL (ADD ASPHALT PAVER UNIT)

HP D-off


107BG-260 DA30CA007 $258,278 20.32 2.66 11.28 17112.8258.66ASPHALT PAVER, ASPHALT WINDROW ELEVATOR, WHEEL (ADD ASPHALT PAVER UNIT)

HP D-off

LEE-BOY

1103000A30LD001 $151,834 11.50 1.57 11.59 1987.3240.53ASPHALT PAVER, ASPHALT FORCE FEED LOADER, 30" WIDE BELT, WINDROW OR LOOSE, WHEEL (ADD ASPHALT PAVER UNIT)

HP D-off

ROADTEC ( ASTEC INDUSTRIES COMPANY)

275SB-1500A30RT001 $539,161 43.08 5.56 28.99 60027.10128.15ASPHALT PAVER, ASPHALT MATERIAL TRANSFER VEHICLE, 15 TON HOPPER, 600 TPH, 65" WIDE CONVEYOR, WHEEL

HP D-off

275SB-2500BA30RT002 $565,516 45.15 5.83 28.99 79028.41132.85ASPHALT PAVER, ASPHALT MATERIAL TRANSFER VEHICLE, 25 TON HOPPER, 1000 TPH, 69" WIDE CONVEYOR, WHEEL

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-33


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

ASPHALT PAVING KETTLESA350.00 ASPHALT PAVING KETTLESSUBCATEGORY

AEROIL PRODUCTS COMPANY, INC.

5KEB-80TA35AE001 $5,316 0.62 0.06 1.06 90.374.63ASPHALT/PAVEMENT KETTLE, 80 GAL, TRAILER W/PUMP & HOSE

HP G


HP G


HP G


HP G


HP G

ASPHALT & CONCRETE MILLERS / PROFILERS / PLANERS / ROTARY GRINDERSA400.00 ASPHALT & CONCRETE MILLERS / PROFILERS / PLANERS / ROTARY GRINDERSSUBCATEGORY


575PM-200A40CA008 $547,479 73.00 5.94 87.98 50542.44276.97ASPHALT COLD PLANER, 75" W X 10" D, CRAWLER (ADD CUTTING TEETH COSTS)

HP D-off

650PM-201A40CA009 $627,305 83.64 6.81 99.45 73548.63315.84ASPHALT COLD PLANER, 83" W X 12" D, CRAWLER (ADD CUTTING TEETH COSTS)

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-34


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

TEREX - CMI (TEREX ROADBUILDING)

950PR-950A40CW001 $852,005 113.60 9.25 145.35 1,20566.05440.51ASPHALT PROFILER, MAX 12.5' W X 15" D, CRAWLER (ADD CUTTING TEETH COSTS)

HP D-off

ROADTEC ( ASTEC INDUSTRIES COMPANY)

230RX-20BA40RT001 $352,508 45.09 3.83 35.19 32426.38152.92ASPHALT COLD PLANER, 40" W X 10" D, WHEEL (ADD CUTTING TEETH COSTS)

HP D-off

250RX-25A40RT002 $460,871 61.45 5.00 38.25 42035.73192.92ASPHALT COLD PLANER, 52" W X 8" D, CRAWLER (ADD CUTTING TEETH COSTS)

HP D-off

460RX-45BA40RT003 $567,654 75.69 6.16 70.38 61744.01263.77ASPHALT COLD PLANER, 78" W X 12" D, CRAWLER (ADD CUTTING TEETH COSTS)

HP D-off


HP D-off


HP D-off

ASPHALT RECYCLERS & SEALERSA450.00 ASPHALT RECYCLERS & SEALERSSUBCATEGORY

AEROIL PRODUCTS COMPANY, INC.

HEPR-52VA45AE001 $13,055 2.02 0.15 0.00 111.1611.82ASPHALT RESURFACER-PATCHER, 4' WIDE, 17.3 SF, 600,000 BTU INFRA-RED HEATER, TRAILER MTD

EP 1110-1-8, Vol. 430 Nov 11

2-35


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

A45 AEROIL PRODUCTS COMPANY, INC. (continued)

HEPR-96VA45AE002 $20,124 3.15 0.22 0.00 161.8021.55ASPHALT RESURFACER-PATCHER, 8' WIDE, 32.0 SF, 1,200,000 BTU INFRA-RED HEATER, TRAILER MTD

IPRS96VA45AE003 $46,157 7.33 0.51 0.00 174.1833.72ASPHALT RESURFACER-PATCHER, 10' WIDE, 40.0 SF, 1,420,000 BTU INFRA-RED HEATER, TRAILER MTD


80RA-2000A45RS001 $50,811 8.04 0.57 8.43 604.5928.51ASPHALT SPRAY PATCHER, 300 GAL, ARTICULATED BOOM - 17' R, TRAILER MTD

HP D-off

210RA-300A45RS002 $163,041 26.09 1.81 25.39 17914.8688.82ASPHALT SPRAY PATCHER, 400 GAL, TELESCOPIC BOOM - 22' EXT, TRUCK MTD

HP D-on

SEALMASTER, INC.

30SP300 DUALA45SE003 $40,001 6.30 0.45 3.16 433.6020.17ASPHALT SEALCOATER, 320 GAL, 75 GPM, 108" WIDE DUAL SPRAY, SQUEEGEE, SELF PROPELLED

HP D-off

13TR-1000A45SE004 $25,516 3.89 0.28 2.77 522.2312.80ASPHALT SEALCOATER, 1000 GAL, 50 GPM, 88'' WIDE SPRAY BAR, TRAILER MTD

HP G

EP 1110-1-8, Vol. 430 Nov 11

2-36


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

BATCH PLANTS, ASPHALT & CONCRETEB100.20 CONCRETESUBCATEGORY

CEMEN TECH

18MCD2-50HTB10CC007 $50,366 4.92 0.53 3.83 802.9919.70BATCH PLANT, CONCRETE DISPENSER, 15 CY/HR MAX, W/TWO AGGREGATE BINS, 2 CY/ 1 CY CEMENT BIN/ 7' LONG SLOPING 8" DIA SCREW WET MIXER/DELIVERER/ 250 GAL WATER TANK/ & METERING PUMP, 2 CY LOAD, TRAILER MTD

HP G

163MCD5-100B10CC008 $54,828 5.11 0.58 34.72 1323.1456.68BATCH PLANT, CONCRETE DISPENSER, 30 CY/HR MAX, W/TWO AGGREGATE BINS, 5.5 CY/ 1.9 CY CEMENT BIN/ 9' LONG SLOPING 9" DIA SCREW WET MIXER/DELIVERER/ 250 GAL WATER TANK/ & METERING PUMP, 5 CY LOAD, TRUCK MTD

HP G


HP G


HP G

EP 1110-1-8, Vol. 430 Nov 11

2-37


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

B10 CEMEN TECH (continued)18210 BBLB10CC012 $24,225 2.42 0.25 3.83 351.4611.08BATCH PLANT, SILO, CEMENT, 830 CF, 210

BARREL (BATCH PLANT ATTACHMENT)

HP G

20HS-240B10CC011 $23,332 2.33 0.25 1.05 451.428.32BATCH PLANT, SILO, CEMENT, 38 TON HORIZONTAL 240 BARREL (BATCH PLANT ATTACHMENT)

HP E

18300 BBLB10CC013 $31,806 3.18 0.33 3.83 481.9213.00BATCH PLANT, SILO, CEMENT, 1,200 CF, 300 BARRL (BATCH PLANT ATTACHMENT)

HP G

5B10CC014 $7,194 0.72 0.08 0.26 100.442.67BATCH PLANT, CEMENT LOADING AUGER, 6" DIA, 19' LONG (BATCH PLANT ATTACHMENT)

HP E

CON-E-CO

200MTM 12B10CL025 $296,350 29.44 3.12 10.53 13017.8488.65BATCH PLANT, CONCRETE MIXER, 12 CY, TILT DRUM, 11.67' DIA, REMOVABLE AXLES, TRAILER MTD (ADD DRY BATCH PLANT)

HP E

35VERSA-PLANT 10

B10CL021 $91,513 8.79 0.96 1.84 1905.3625.09BATCH PLANT, CONCRETE AGGREGATE DRY, 40CY/HR, 10 CY AGGREGATE BATCHER, W/30" X 40' LOADING CONVEYOR, SCALES & WATER METER INCLUDED, TRAILER MTD (ADD 5 KW GENERATOR, WATER TANK & WET BATCHER)

HP E

30PLP MODEL 12B10CL015 $171,173 16.51 1.80 1.58 38010.0646.70BATCH PLANT, CONCRETE AGGREGATE DRY, 200 CY/HR, W/TWO AGGREGATE BINS, 81 TON, 60 CY/ 36"X20' CONVEYOR/ 3 BIN 12 CY AGGREGATE BATCHER/ 30"X33.5' LOADING CONVEYOR/ & 475 BARREL, 88 TON CEMENT SILO, TRAILER MTD (ADD 110 KW GENERATOR)

HP E

EP 1110-1-8, Vol. 430 Nov 11

2-38


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

B10 CON-E-CO (continued)B10CL027 $22,790 2.28 0.24 0.00 1441.385.62BATCH PLANT, CEMENT SILO, 1,910 CF,

475 BARREL (BATCH PLANT ATTACHMENT)

5B10CL042 $3,449 0.34 0.04 0.26 50.211.24BATCH PLANT, SCREW CONVEYOR, 6" DIA, 10' LONG (CEMENT SILO ATTACHMENT)

HP E


HP E


HP E


HP E


HP E


HP E

EXCEL MACHINERY LTD.

25EXCEL PORT-A-PUG

B10EM001 $462,895 45.20 4.87 5.32 59027.47122.03BATCH PLANT, CONCRETE CONTINUOUS PUGG MILL MIXER, 400 CY/HR MAX, W/12 CY AGGREGATE STORAGE BIN/ 48"X18' METERING CONVEYOR/ CEMENT SILO, 44 TON, 34.8 CY/ 30" X 37' CONVEYOR, TRAILER MTD (ADD 200 KW GENERATOR)

HP G

EP 1110-1-8, Vol. 430 Nov 11

2-39


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

B10 EXCEL MACHINERY LTD. (continued)10B10EM002 $31,804 2.87 0.33 0.53 451.779.43BATCH PLANT, CEMENT SILO, 45 TON

HORIZONTAL 350 BARREL (BATCH PLANT ATTACHMENT)

HP E

B10EM003 $29,656 2.97 0.31 0.00 2221.807.31BATCH PLANT, CEMENT SILO, 2,200 CF (BARREL CAP 550 MAX / 450 MIN) W/DRIVE-THRU TYPE UNDERSTRUCTURE (BATCH PLANT ATTACHMENT)

JOHNSON-ROSS (TEREX ROADBUILDING)

15BANDIT 5B10RC007 $146,261 14.21 1.54 0.79 3,0008.6539.47BATCH PLANT, CONCRETE AGGREGATE DRY, 100 CY/HR, W/TWO AGGREGATE BINS, 65 TON, 48 CY/ 36" X 20' CONVEYOR/ 2 BIN 5 CY BATCHER/ 30" X 33.5' LOADING CONVEYOR/ & 257 BARREL, 48 TON CEMENT SILO, TRAILER MTD (ADD 100 KW GENERATOR)

HP E

50RUSTLER IIIB10RC032 $225,095 21.82 2.37 2.63 53613.2863.49BATCH PLANT, CONCRETE AGGREGATE DRY, 160 CY/HR, W/TWO AGGREGATE BINS, 28 TON, 21 CY/ 2 BIN 12 CY BATCHER/ 30" X 33.5' LOADING CONVEYOR/ & 400 BARREL, 75 TON CEMENT SILO, TRAILER MTD (ADD 130 KW GENERATOR)

HP E

46RUSTLER IIB10RC006 $207,790 20.09 2.19 2.40 48912.2458.89BATCH PLANT, CONCRETE AGGREGATE DRY, 160 CY/HR, W/3 AGGREGATE BINS, 71 TON, 52 CY/ 36" X 20' CONVEYOR/ 3 BIN 12 CY BATCHER/ 30" X 33.5' LOADING CONVEYOR/ 375 BARREL, 70 TON CEMENT SILO, TRAILER MTD (ADD 130KW GENERATOR)

HP E

EP 1110-1-8, Vol. 430 Nov 11

2-40


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

B10 JOHNSON-ROSS (TEREX ROADBUILDING) (continued)

30BANDIT 12 BTRB10RC008 $174,072 16.99 1.83 1.58 25010.3347.50BATCH PLANT, CONCRETE AGGREGATE DRY, 200 CY/HR, W/THREE AGGREGATE BINS, 65 TON, 48 CY/ 36" X 20' CONVEYOR/ 3 BIN 12 CY BATCHER/ 30" X 33.5' LOADING CONVEYOR/ & 720 BARREL, 134 TON CEMENT SILO, TRAILER MTD (ADD 100 KW GENERATOR)

HP E

40B10RC027 $157,955 15.80 1.66 2.11 349.5644.08BATCH PLANT, CONCRETE MIXER, 4.5 CY, TILT DRUM, SKID MTD (ADD DRY BATCH PLANT)

HP E


HP E


HP E


HP E


HP E

75MOBILE MIXERB10RC016 $255,402 24.85 2.69 3.95 42015.1273.94BATCH PLANT, CONCRETE MIXER, 4.5CY, TILT DRUM TYPE, REVOLVING LIFT STAND, TRAILER MTD (ADD DRY BATCH PLANT & POWER)

HP E

EP 1110-1-8, Vol. 430 Nov 11

2-41


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

STEPHENS MANUFACTURING CO., INC.

25DC-12B10SN031 $81,582 7.41 0.86 1.32 3404.5722.98BATCH PLANT, CONCRETE AGGREGATE DRY, 100 CY/HR, W/2 BIN 12 CY BATCHER/ 24" X 41' LOADING CONVEYOR/ & 311 BARREL, 58 TON CEMENT SILO, TRAILER MTD (ADD 100 KW GENERATOR)

HP E

30DC COLTB10SN033 $152,677 14.53 1.61 1.58 3408.8841.04BATCH PLANT, CONCRETE AGGREGATE DRY, 100 CY/HR, W/2 BIN 12 CY BATCHER/ 30" X 33.5' LOADING CONVEYOR/ & 311 BARREL, 58 TON CEMENT SILO, TRAILER MTD (ADD 100 KW GENERATOR)

HP E

30MUSTANG 5B10SN032 $124,723 11.71 1.31 1.58 4207.1734.38BATCH PLANT, CONCRETE AGGREGATE DRY, 160 CY/HR, W/3 AGGREGATE STORAGE BINS, 29.6 TON, 40 CY/ 3 BIN 5 CY BATCHER/ 30" X 33.5' LOADING CONVEYOR/ & 251 BARREL, 47 TON CEMENT SILO, TRAILER MTD (ADD 115 KW GENERATOR)

HP E

20STALLIONB10SN034 $165,647 15.80 1.74 1.05 3609.6443.42BATCH PLANT, CONCRETE AGGREGATE DRY, 160 CY/HR, W/3 AGGREGATE BIN STORAGE, 70 TON, 48 CY/ 2 BIN 10 CY BATCHER/ 30" X 33.5' LOADING CONVEYOR/ & 374 BARREL, 70 TON CEMENT SILO, TRAILER MTD (ADD 100 KW GENERATOR)

HP E

45MUSTANG 10B10SN036 $162,838 15.52 1.71 2.37 5009.4744.96BATCH PLANT, CONCRETE AGGREGATE DRY, 160 CY/HR, W/3 AGGREGATE BIN STORAGE, 75 TON, 55 CY/ 2 BIN 10 CY BATCHER/ 30" X 33.5' LOADING CONVEYOR/ & 351 BARREL, 65 TON CEMENT SILO, TRAILER MTD (ADD 115 KW GENERATOR)

HP E

EP 1110-1-8, Vol. 430 Nov 11

2-42


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

B10 STEPHENS MANUFACTURING CO., INC. (continued)

30THOROUGH-BRED

B10SN035 $173,780 16.62 1.83 1.58 30010.1446.38BATCH PLANT, CONCRETE AGGREGATE DRY, 180 CY/HR, W/4 AGGREGATE BIN STORAGE, 65 TON, 48 CY/ 2 BIN 12 CY BATCHER/ 30" X 33.5' LOADING CONVEYOR/ & 374 BARREL, 70 TON CEMENT SILO, TRAILER MTD (ADD 100 KW GENERATOR)

HP E

0.30 PUGMILLSUBCATEGORY

KOLBERG - PIONEER, INC

9552 PORTABLE PUGMILL

B10KB001 $184,336 14.43 1.90 5.00 1909.1244.11BATCH PLANT, PUGMILL, CONTINUOUS MIXER, 48" DIA TWIN SHAFT X 6' LONG, W/9 CY FEEDER HOPPER/ 36" X 11.5' BELT FEEDER/ 30" X 27' CONVEYOR/ WATER OR ASPHALT PUMP & METER (ADD 95 KW GENERATOR & ANY MATERIAL FEEDS)

HP E

22052S PORTABLE PUGMILL

B10KB002 $328,244 25.91 3.39 11.58 23016.3582.60BATCH PLANT, PUGMILL, CONTINUOUS MIXER, 48" DIA TWIN SHAFT X 8' LONG, W/13 CY FEEDER HOPPER/ TWO - 36" X 11.5' BELT FEEDERS/ 2ND 11 CY FEEDER HOPPER/ 30" X 27' CONVEYOR/ WATER OR ASPHALT PUMP & METER (ADD 220 KW GENERATOR & ANY MATERIAL FEEDS)

HP E

EP 1110-1-8, Vol. 430 Nov 11

2-43


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

BROOMS, STREET SWEEPERS & FLUSHERSB150.00 BROOMS, STREET SWEEPERS & FLUSHERSSUBCATEGORY

BROCE MANUFACTURING COMPANY

80RJ-350B15BM001 $47,350 5.33 0.47 8.43 503.1420.47BROOM, 8' BROOM PATH, PAVEMENT, SELF PROPELLED

HP D-off

ELGIN SWEEPER COMPANY

100PELICAN PB15EC002 $129,554 14.40 1.28 10.54 1288.4841.99STREET SWEEPER, 10' BROOM PATH, 3.5 CY HOPPER, 180 GAL WATER TANK, SELF PROPELLED

HP D-off

49EAGLE FB15EC001 $211,401 23.46 2.08 9.14 15013.8159.55170 HP D-onSTREET SWEEPER, 10' BROOM PATH, 4.5 CY HOPPER, 280 GAL WATER TANK, DUAL ENGINE, SELF PROPELLED

HP D-off

230BROOM BEAR FL42H

B15EC003 $202,731 22.76 2.00 24.24 21313.3874.34STREET SWEEPER, 12' BROOM PATH, 4.5 CY HOPPER, 350 GAL WATER TANK, SELF PROPELLED

HP D-off

115MEGAWINDB15EC004 $224,597 25.27 2.21 16.81 23814.8571.05230 HP D-offSTREET SWEEPER AND CATCH BASIN CLEANER, 12' BROOM PATH, 13 CY HOPPER, 335 GAL WATER TANK, SELF PROPELLED

HP D-off

M-B COMPANIES, INC.

MT-ARB15MB001 $8,307 0.93 0.08 0.00 100.552.02STREET SWEEPER, 7' BROOM PATH, W/SPRINKLER AND 152 GAL WATER TANK, PTO DRIVE (ADD 45-100 HP TRACTOR)

EP 1110-1-8, Vol. 430 Nov 11

2-44


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

B15 M-B COMPANIES, INC. (continued)HTB15MB002 $10,036 1.13 0.10 0.00 120.672.47STREET SWEEPER, 7' BROOM PATH,

W/SPRINKLER AND 152 GAL WATER TANK, PTO DRIVE (ADD 45-100 HP TRACTOR)

53TB15MB003 $14,601 1.58 0.14 0.00 180.933.61STREET SWEEPER, 7' BROOM PATH, W/SPRINKLER AND 152 GAL WATER TANK, TOWED, HYDRAULIC (ADD TOWING UNIT)

1853MHB15MB004 $16,840 1.83 0.17 3.83 171.098.13STREET SWEEPER, 7' BROOM PATH, W/SPRINKLER AND 152 GAL WATER TANK, TOWED (ADD TOWING UNIT)

HP G


80CHALLENGER IIB15RS005 $53,811 5.96 0.53 8.43 753.5122.00STREET SWEEPER, 7' BROOM PATH, W/SPRINKLER AND 125 GAL WATER TANK, SELF PROPELLED

HP D-off

80RB-48B15RS001 $41,379 4.60 0.41 8.43 522.7119.11STREET SWEEPER, 8' BROOM PATH, W/SPRINKLER AND 150 GAL WATER TANK, SELF PROPELLED

HP D-off

TERRAMITE CONSTRUCTION EQUIPMENT

37TSS46B15TB001 $23,598 2.59 0.23 3.90 341.539.90STREET SWEEPER, 6' BROOM PATH, W/SPRINKLER AND 2 - 50 GAL WATER TANKS, SELF PROPELLED

HP D-off

37TSS48B15TB002 $23,746 2.60 0.23 3.90 341.539.93STREET SWEEPER, 8' BROOM PATH, W/SPRINKLER AND 2 - 50 GAL WATER TANKS, SELF PROPELLED

HP D-off

WALDON, INC.

80SWEEPMASTER 250

B15WD001 $37,250 4.13 0.37 8.43 482.4418.14BROOM, 7.5' BROOM PATH, PAVEMENT, SELF PROPELLED

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-45


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

B15 WALDON, INC. (continued)80SWEEPMASTER

250B15WD002 $38,690 4.30 0.38 8.43 482.5318.48BROOM, 90" BROOM PATH, PAVEMENT,

W/SPRINKLER AND 180 GAL WATER TANK, SELF PROPELLED

HP D-off

BRUSH CHIPPERSB200.00 BRUSH CHIPPERSSUBCATEGORY

BANDIT INDUSTRIES, INC.

4465XPB20BN001 $11,310 1.25 0.11 9.37 190.7413.47BRUSH CHIPPER, 6" CAPACITY, DISC TYPE, TRAILER MTD

HP G


HP G


HP G

1421390XPB20BN005 $22,565 2.50 0.22 30.24 661.4740.04BRUSH CHIPPER, 13" CAPACITY, DRUM TYPE, TRAILER MTD

HP G


HP G


HP D-off

MORBARK, INC.

84M12RB20MQ001 $30,679 3.44 0.30 8.85 452.0217.48BRUSH CHIPPER, 12" CAPACITY, DRUM TYPE, TRAILER MTD

HP D-off


HP D-off


HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-46


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

B20 MORBARK, INC. (continued)87522 RXLB20MQ005 $520,239 58.03 5.13 92.23 81334.15233.01BRUSH CHIPPER, LOG CHIPPER, 22"

CAPACITY, DISC TYPE, TRAILER MTD

HP D-off

BUCKETS, CLAMSHELLB250.00 BUCKETS, CLAMSHELLSUBCATEGORY

HAWCO MANUFACTURING COMPANY, LLC

HD-050B25HB001 $19,075 2.15 0.19 0.00 301.274.15BUCKET, CLAMSHELL, 0.5 CY, HEAVY DUTY/DIGGING










EP 1110-1-8, Vol. 430 Nov 11

2-47


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

B25 HAWCO MANUFACTURING COMPANY, LLC (continued)




1/4SSNB25XX001 $8,620 0.97 0.08 0.00 140.571.87BUCKET, CLAMSHELL, 0.2 CY, SQUARE NOSE, STANDARD



1SSNB25XX004 $17,260 1.94 0.17 0.00 431.143.75BUCKET, CLAMSHELL, 1.0 CY, SQUARE NOSE, STANDARD

1-1/4SSNB25XX005 $20,107 2.26 0.20 0.00 491.334.37BUCKET, CLAMSHELL, 1.2 CY, SQUARE NOSE, STANDARD






EP 1110-1-8, Vol. 430 Nov 11

2-48


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

B25 NO SPECIFIC MANUFACTURER (continued)3-1/2SSNB25XX011 $33,127 3.73 0.33 0.00 1082.207.21BUCKET, CLAMSHELL, 3.5 CY, SQUARE

NOSE, STANDARD 4SSNB25XX012 $37,001 4.16 0.36 0.00 1192.448.04BUCKET, CLAMSHELL, 4.0 CY, SQUARE

NOSE, STANDARD 4-1/2SSNB25XX013 $49,787 5.60 0.49 0.00 1453.2910.82BUCKET, CLAMSHELL, 4.5 CY, SQUARE







NOSE, STANDARD

BUCKETS, CONCRETEB300.10 GENERAL PURPOSE, MANUAL TRIPSUBCATEGORY

GAR-BRO MANUFACTURING COMPANY

413-GB30GB018 $3,262 0.39 0.03 0.00 40.230.73BUCKET, CONCRETE, GENERAL PURPOSE, 0.5 CY


EP 1110-1-8, Vol. 430 Nov 11

2-49


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

B30 GAR-BRO MANUFACTURING COMPANY (continued)





0.20 LAYDOWNSUBCATEGORY


425-AB30GB006 $25,776 3.06 0.25 0.00 261.785.93BUCKET, CONCRETE, LAYDOWN, 1.0 CY, HEAVY DUTY AIR GATE





0.30 LOWBOYSUBCATEGORY

CAMLEVER

LB-375B30CR001 $4,471 0.53 0.04 0.00 20.311.06BUCKET, CONCRETE, LOWBOY, 0.38 CY

EP 1110-1-8, Vol. 430 Nov 11

2-50


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

B30 CAMLEVER (continued)LB-050B30CR002 $5,016 0.60 0.05 0.00 20.351.19BUCKET, CONCRETE, LOWBOY, 0.5

CY LB-075B30CR003 $5,564 0.66 0.05 0.00 30.381.31BUCKET, CONCRETE, LOWBOY, 0.75



CY LXB-150B30CR009 $7,788 0.92 0.07 0.00 60.531.84BUCKET, CONCRETE, LOWBOY, 1.5





CY

0.40 LOW SLUMPSUBCATEGORY


440-AB30GB011 $16,702 1.98 0.16 0.00 201.153.95BUCKET, CONCRETE, LOW SLUMP, 1.0 CY, AIR GATE



EP 1110-1-8, Vol. 430 Nov 11

2-51


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

B30 GAR-BRO MANUFACTURING COMPANY (continued)





BUCKETS, DRAGLINEB350.10 LIGHT WEIGHTSUBCATEGORY

HENDRIX MANUFACTURING COMPANY, INC.

LSB35HE001 $7,853 0.88 0.08 0.00 150.521.71BUCKET, DRAGLINE, 0.75 CY, LIGHT WEIGHT/PERFORATED







EP 1110-1-8, Vol. 430 Nov 11

2-52


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

B35 HENDRIX MANUFACTURING COMPANY, INC. (continued)











SAUERMAN (NATIONAL OILWELL VARCO)

SC-1050-KB35SA001 $56,563 6.36 0.56 0.00 153.7412.29BUCKET, DRAGLINE, 1.0 CY, CRESCENT, W/CARRIER


EP 1110-1-8, Vol. 430 Nov 11

2-53


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

B35 SAUERMAN (NATIONAL OILWELL VARCO) (continued)






SC-1140-KB35SA009 $424,112 47.71 4.18 0.00 10628.0492.18BUCKET, DRAGLINE, 10.0 CY,CRESCENT, W/CARRIER

SC-1150-KB35SA010 $509,017 57.26 5.02 0.00 13233.65110.64BUCKET, DRAGLINE, 12.0 CY,CRESCENT, W/CARRIER


6-1/2LB35XX001 $31,192 3.51 0.31 0.00 942.076.78BUCKET, DRAGLINE, 6.5 CY, LIGHT WEIGHT




11LB35XX005 $49,662 5.59 0.49 0.00 1483.2910.80BUCKET, DRAGLINE, 11.0 CY, LIGHT WEIGHT

EP 1110-1-8, Vol. 430 Nov 11

2-54


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

B35 NO SPECIFIC MANUFACTURER (continued)13LB35XX006 $61,093 6.87 0.60 0.00 1784.0413.27BUCKET, DRAGLINE, 13.0 CY, LIGHT

WEIGHT

0.20 MEDIUM WEIGHTSUBCATEGORY


TSB35HE018 $8,487 0.85 0.08 0.00 170.511.65BUCKET, DRAGLINE, 0.75 CY, MEDIUM WEIGHT











EP 1110-1-8, Vol. 430 Nov 11

2-55


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

B35 HENDRIX MANUFACTURING COMPANY, INC. (continued)








6-1/2MB35XX007 $35,254 3.53 0.34 0.00 1012.116.85BUCKET, DRAGLINE, 6.5 CY, MEDIUM WEIGHT




11MB35XX011 $57,101 5.71 0.56 0.00 1693.4211.09BUCKET, DRAGLINE, 11.0 CY, MEDIUM WEIGHT

13MB35XX012 $72,361 7.24 0.70 0.00 2114.3214.05BUCKET, DRAGLINE, 13.0 CY, MEDIUM WEIGHT

EP 1110-1-8, Vol. 430 Nov 11

2-56


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

0.30 HEAVY WEIGHTSUBCATEGORY


MH-SB35HE035 $31,694 2.85 0.31 0.00 691.745.57BUCKET, DRAGLINE, 2.75 CY, HEAVY WEIGHT













EP 1110-1-8, Vol. 430 Nov 11

2-57


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)


3/4HB35XX013 $8,886 0.80 0.09 0.00 200.491.57BUCKET, DRAGLINE, 0.75 CY, HEAVY WEIGHT

1HB35XX014 $9,982 0.90 0.10 0.00 230.551.76BUCKET, DRAGLINE, 1.0 CY, HEAVY WEIGHT

1-1/2HB35XX015 $14,844 1.34 0.14 0.00 350.812.61BUCKET, DRAGLINE, 1.5 CY, HEAVY WEIGHT









EP 1110-1-8, Vol. 430 Nov 11

2-58


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

CHAIN SAWSC050.00 CHAIN SAWSSUBCATEGORY

OLYMPYK CHAIN SAWS

2941C05OL001 $358 0.16 0.00 0.67 10.081.41CHAIN SAW, 16"-18" BAR HP G




COMPACTORS, WALK-BEHIND OR REMOTE CONTROLLERC100.10 COMPACTORS, RAMMERS / TAMPERS & VIBRATORY PLATESSUBCATEGORY

COMPACTION AMERICA (BOMAG)

3BT 60/4C10BO001 $3,939 0.94 0.04 0.88 20.513.25COMPACTOR, RAMMER, TAMPER, 11" X 13.2" SHOE, 2,630 LBS IMPACT

HP G

4BP 10/36-2C10BO003 $1,512 0.36 0.02 1.17 20.202.17COMPACTOR, VIBROPLATE, 14.2" X 22" PLATE, 2,250 LBS IMPACT

HP G

6BP 18/45-2C10BO004 $1,775 0.42 0.02 1.75 20.232.95COMPACTOR, VIBROPLATE, 17.7" X 22" PLATE, 4,050 LBS IMPACT

HP G

9BPR 55/65DC10BO008 $15,582 3.70 0.17 1.32 102.0210.46COMPACTOR, VIBROPLATE, 25.6" X 35.4" PLATE, REVERSIBLE, 11,250 LBS IMPACT

HP D-off

WACKER CORPORATION

4DS 70C10WC00 $4,017 0.95 0.04 0.58 20.522.95COMPACTOR, RAMMER, 13" X 13" SHOE, 3,550 LBS IMPACT

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-59


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

C10 WACKER CORPORATION (continued)6BPU 2540 AC10WC00 $4,916 1.17 0.05 1.61 30.644.62COMPACTOR, VIBROPLATE, 19.5" X 25.5"

PLATE, REVERSIBLE, 5,600 LBS IMPACT

HP G

9BPU 3545AC10WC00 $7,518 1.79 0.08 2.63 70.987.26COMPACTOR, VIBROPLATE, 23.5" X 35.5" PLATE, REVERSIBLE, 7,550 LBS IMPACT

HP G

9DPU 4045HC10WC00 $13,569 3.22 0.15 1.32 71.769.30COMPACTOR, VIBROPLATE, 24" X 35.5" PLATE, REVERSIBLE, 9,000 LBS IMPACT

HP D-off

14DPU 7060C10WC01 $26,865 6.38 0.29 2.05 153.4817.79COMPACTOR, VIBROPLATE, 25.5" X 42" PLATE, REVERSIBLE, 15,600 LBS IMPACT

HP D-off

0.20 ROLLERS, VIBRATORYSUBCATEGORY


4BW 55EC10BO009 $8,051 1.71 0.09 1.17 30.955.74COMPACTOR, ROLLER, VIBRATORY, 22"W X 15.7"DIA, SINGLE SMOOTH DRUM, WALK BEHIND, 2,273 LBS IMPACT

HP G

5BW65HS-DC10BO015 $18,882 4.01 0.21 0.73 132.2211.25COMPACTOR, ROLLER, VIBRATORY, 25.6"W X 15.7"DIA, DOUBLE SMOOTH DRUMS, WALK BEHIND, 2,655 LBS IMPACT

HP D-off

8BW 65HC10BO011 $21,229 4.51 0.24 1.17 162.5013.03COMPACTOR, ROLLER, VIBRATORY, 25.6"W X 15.7"DIA, DOUBLE SMOOTH DRUMS, WALK BEHIND, 1,980 LBS IMPACT

HP D-off

9BW75S-DC10BO016 $23,679 5.03 0.27 1.32 202.7914.56COMPACTOR, ROLLER, VIBRATORY, 29.5"W X 18.9"DIA, DOUBLE SMOOTH DRUMS, WALK BEHIND, 4,455 LBS IMPACT

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-60


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

C10 COMPACTION AMERICA (BOMAG) (continued)

19BMP851C10BO013 $48,512 10.31 0.55 2.78 455.7129.91COMPACTOR, TRENCH ROLLER, VIBRATORY, 33.5"W X 19.7"DIA, DOUBLE TAMPING FOOT DRUMS, WALK BEHIND, 18,000 LBS IMPACT

HP D-off

RAMMAX MACHINERY CO.

8P23/16FMC10RX001 $31,609 6.72 0.36 1.17 163.7218.79COMPACTOR, TRENCH ROLLER, VIBRATORY, 23"W X 14.6"DIA, QUAD PADFOOT DRUMS, WALK BEHIND, 7,875 LBS IMPACT

HP D-off

14P33/24FMRC10RX002 $43,661 9.28 0.49 2.05 305.1326.43COMPACTOR, TRENCH ROLLER, VIBRATORY, 33"W X 21.7"DIA, QUAD PADFOOT DRUMS, WALK BEHIND, 15,652 LBS IMPACT

HP D-off

33P47/40KMC10RX003 $73,074 15.53 0.82 4.82 668.5945.76COMPACTOR, TRENCH ROLLER, VIBRATORY, 47"W X 22"DIA, QUAD PADFOOT DRUMS, RIDE ON, 21,600 LBS IMPACT

HP D-off

WACKER CORPORATION

11RSS800AC10WC01 $10,242 2.18 0.12 3.22 111.219.23COMPACTOR, ROLLER, VIBRATORY, 28"W X 22"DIA, SINGLE SMOOTH DRUM, WALK BEHIND, 3,400 LBS IMPACT

HP G

9RD7HC10WC01 $13,553 2.88 0.15 1.32 161.598.96COMPACTOR, ROLLER, VIBRATORY,25.5"W X 16.5"DIA, DOUBLE SMOOTH DRUM, WALK BEHIND, 2,925 LBS IMPACT

HP D-off

20RT 56-SCC10WC01 $31,831 6.76 0.36 2.92 313.7420.84COMPACTOR, ROLLER, VIBRATORY, 22"W X 20"DIA, DOUBLE SMOOTH DRUM, WALK BEHIND, 7,000/14,000 LBS IMPACT

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-61


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

C10 WACKER CORPORATION (continued)20RT 82-SCC10WC01 $33,573 7.13 0.38 2.92 333.9521.80COMPACTOR, TRENCH ROLLER,

VIBRATORY, 32"W X 20"DIA, DOUBLE TAMPING FOOT DRUMS, WALK BEHIND, 7,000/14,000 LBS IMPACT

HP D-off

CONCRETE CLEANERS / ABRASIVE BLASTERSC150.10 WALK BEHINDSUBCATEGORY

US FILTER/BLASTRAC

21-8DEC & BDC-1216

C15BL001 $9,522 1.90 0.11 0.11 21.065.03CONCRETE BLASTER CLEANING SYSTEM, WALK BEHIND, 8" PATH (ADD 4 KVA GENERATOR & BLAST MEDIA COST)

HP E

101-10DSG1 & 6-54DCG1


HP E

151-15DSG1 & 6-54DCG1


HP E

302-20DT & 8-54DCG1


HP E

EQUIPMENT DEVELOPMENT CO., INC. (EDCO)

9CPM-8C15ED002 $4,919 0.98 0.06 2.05 20.554.59CONCRETE GRINDER, WALK BEHIND, TRAFFIC LINE REMOVER, 8'' CUTTING PATH

HP G

11TLR-7C15ED001 $8,143 1.63 0.09 2.50 50.916.58CONCRETE GRINDER, WALK BEHIND, TRAFFIC LINE REMOVER, 7'' CUTTING WIDTH

HP G

EP 1110-1-8, Vol. 430 Nov 11

2-62


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

0.20 TRUCK/TRAILER MOUNTEDSUBCATEGORY

US FILTER/BLASTRAC

3502-4800 DHC15BL006 $451,967 45.20 4.76 53.55 25527.36165.95CONCRETE BLASTER, SELF PROPELLED, 48'' PATH

HP D-off


86C15XX001 $139,646 13.77 1.47 29.78 1388.3666.24180 HP D-offCONCRETE CLEANER/ABRASIVE BLASTER, TRUCK MOUNTED, GINDER/BLASTER, 4" - 16" CLEANING PATH WIDTH

HP D-on

CONCRETE BUGGIESC200.00 CONCRETE BUGGIESSUBCATEGORY

WACKER CORPORATION

13WB 16AC20WC00 $12,066 2.21 0.14 2.96 131.258.11CONCRETE BUGGY, 16 CF BUCKET, 2,500 LBS, WALK & RIDE, 4X2

HP G


810GC20XX001 $8,463 1.55 0.10 1.82 100.885.40CONCRETE BUGGY, 10 CF BUCKET, 1,500 LBS

HP G

CONCRETE FINISHERS/SCREEDS/SPREADERSC250.10 FINISHERS/TROWELSSUBCATEGORY

ALLEN ENGINEERING CORP.

20PRO 900C25AJ015 $11,906 1.90 0.13 4.55 81.089.31CONCRETE TROWEL, RIDING, 2 - 36" DIA ROTORS, 8 BLADES

HP G

EP 1110-1-8, Vol. 430 Nov 11

2-63


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

C25 ALLEN ENGINEERING CORP. (continued)24PRO 1050C25AJ016 $13,349 2.14 0.15 5.46 91.2210.87CONCRETE TROWEL, RIDING, 2 - 42" DIA

ROTORS, 8 BLADES HP G

24PRO 1200C25AJ018 $13,860 2.22 0.15 5.46 111.2611.04CONCRETE TROWEL, RIDING, 2 - 46" DIA ROTORS, 8 BLADES

HP G

34SUPER PRO 400C25AJ019 $19,034 3.05 0.21 7.73 131.7415.43CONCRETE TROWEL, RIDING, 2 - 46" DIA ROTORS, 8 BLADES

HP G

STOW MANUFACTURING, INC.

8SCT36H80C25ST001 $2,679 0.43 0.03 1.82 30.253.01CONCRETE FINISHER, WALK BEHIND, ROTO TROWEL, 36" DIA ROTOR, 4 BLADES

HP G

9SCT46H80C25ST002 $2,747 0.44 0.03 2.05 30.253.29CONCRETE FINISHER, WALK BEHIND, ROTO TROWEL, 46" DIA ROTOR, 4 BLADES

HP G

WACKER CORPORATION

8CT48ADPC25WC00 $3,356 0.54 0.04 1.82 30.313.25CONCRETE FINISHER, WALK BEHIND, POWER TROWEL, 48" DIA ROTOR, 4 BLADES

HP G

0.20 VIBRATORY SCREEDSUBCATEGORY


612HEDC25AJ003 $8,199 1.31 0.09 1.36 70.754.39CONCRETE, VIBRATORY SCREED, 22.5' WIDE

HP G

612 HDC25AJ001 $4,841 0.77 0.05 1.36 50.443.22CONCRETE, VIBRATORY SCREED, 20' WIDE

HP G

912HEDC25AJ004 $9,257 1.48 0.10 2.05 80.845.55CONCRETE, VIBRATORY SCREED, 32.5' WIDE

HP G

EP 1110-1-8, Vol. 430 Nov 11

2-64


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

C25 ALLEN ENGINEERING CORP. (continued)1112HEDC25AJ005 $10,351 1.66 0.12 2.50 110.956.45CONCRETE, VIBRATORY SCREED, 42.5'

WIDE HP G

1112HEDC25AJ006 $11,699 1.87 0.13 2.50 121.076.91CONCRETE, VIBRATORY SCREED, 50' WIDE

HP G

1112HEDC25AJ007 $12,359 1.98 0.14 2.50 131.137.14CONCRETE, VIBRATORY SCREED, 55' WIDE

HP G

0.25 VIBRATORY LASER SCREEDSUBCATEGORY

SOMERO ENTERPRISES, INC.

30S-100C25SV003 $150,832 13.07 1.69 3.16 728.2331.04CONCRETE, VIBRATORY LASER SCREED, 8' WIDE X 12' BOOM

HP D-off

65SXP (VERSATILE)

C25SV002 $301,518 26.22 3.37 6.85 12616.4862.66CONCRETE, VIBRATORY LASER SCREED, 8' WIDE X 20' BOOM

HP D-off

65SXP (PRODUCTIVE)

C25SV001 $320,850 27.89 3.59 6.85 15117.5466.16CONCRETE, VIBRATORY LASER SCREED, 12' WIDE X 20' BOOM

HP D-off

0.30 MATERIAL/TOPPING SPREADERSSUBCATEGORY


6SP23HC25AJ008 $16,507 1.44 0.18 1.17 110.904.37CONCRETE, MATERIAL/TOPPING SPREADER, 12.5' WIDE

HP G

6SP23HC25AJ009 $17,529 1.53 0.20 1.17 120.974.56CONCRETE, MATERIAL/TOPPING SPREADER, 20' WIDE

HP G


HP G


HP G

EP 1110-1-8, Vol. 430 Nov 11

2-65


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

C25 ALLEN ENGINEERING CORP. (continued)6SP23HC25AJ012 $21,299 1.86 0.24 1.17 151.175.24CONCRETE, MATERIAL/TOPPING

SPREADER, 50' WIDE HP G


HP G

CONCRETE GUNITERS / SHOTCRETERSC350.00 CONCRETE GUNITERS / SHOTCRETERSSUBCATEGORY

AIRPLACO EQUIPMENT CO., INC.

9C-10SLC35AF002 $15,933 1.68 0.18 0.00 61.026.11CONCRETE GUNITER/SHOTCRETER, DRY/SEMI-WET, HOPPER/PUMP/SPRAY, 12 CY/HR, 2" HOSE & 1 GUN (ADD 600 CFM COMPRESSOR)

CFM A

30634D Mix Elevator

C35AF004 $45,346 4.81 0.50 3.67 452.9117.86CONCRETE GUNITER/SHOTCRETER, DRY BATCH MIXER, 13 CY/HR, W/FEEDER, TRAILER MTD (ADD SHOTCRETE MACHINE)

HP D-off

54734LBD Mix Elevator

C35AF005 $66,456 7.02 0.73 6.61 814.2426.61CONCRETE GUNITER/SHOTCRETER, DRY BATCH MIXER, W/20 CY/HR ELEVATOR FEEDER/ 45 CF SAND HOPPER/ 4 CF CEMENT HOPPER/ & PREDAMPENING SPRAY BAR, TRAILER MTD (ADD SHOTCRETE MACHINE)

HP D-off

ALLENTOWN EQUIPMENT

5GRH-610 ROTARY GUN

C35AL003 $16,128 1.57 0.18 0.30 110.974.74CONCRETE GUNITER/SHOTCRETER, ROTARY PUMP, WET/DRY, 1 - 6 CY/HR, W/HOPPER/ 100' - 1.5" DIA HOSE/ & NOZZLE, CART MTD, (ADD 250 - 600 CFM COMPRESSOR)

HP E

EP 1110-1-8, Vol. 430 Nov 11

2-66


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

C35 ALLENTOWN EQUIPMENT (continued)9AG-15

AUTOMATIC GUN

C35AL013 $13,674 1.39 0.15 0.00 150.853.91CONCRETE GUNITER/SHOTCRETER, ROTARY PUMP, WET/DRY, 3 - 15 CY/HR, W/HOPPER/ 100' - 1.5" DIA HOSE/ & NOZZLE (ADD 300 - 900 CFM COMPRESSOR)

CFM A

9N-2 PNEUMATIC GUN

C35AL008 $26,367 2.83 0.29 0.00 131.717.14CONCRETE GUNITER/SHOTCRETER, DRY MIX, 2 - 8 CY/HR, W/2 PRESSURIZED TANKS/ 100' - 1.5" DIA HOSE/ & NOZZLE (ADD 200 - 900 CFM COMPRESSOR)

CFM A

30R-900 BATCH MIX RIG

C35AL002 $45,290 4.69 0.50 3.67 472.8516.77CONCRETE GUNITER/SHOTCRETER, DRY BATCH MIXER, 10 TON/HR, W/ELEVATOR FEEDER/ 20 CF CEMENT HOPPER/ 8 CF MIXER/ & PREDAMPENING SPRAY BAR, TRAILER MTD (ADD SHOTCRETE MACHINE OR ROTARY PUMP)

HP D-off

61POWER CRETER 10

C35AL014 $69,190 7.37 0.76 7.47 304.4526.81CONCRETE GUNITER/SHOTCRETER, GROUT/MUD JACK/ SHOTCRETE, 10 CY/HR, 2,085 PSI, W/30 GAL HOPPER/ 74 GAL MIXER, TRAILER MTD (ADD 3" HOSE LINE)

HP D-off

ALIVA LTD.

7AL 246C35AV008 $28,395 3.04 0.31 0.43 91.8310.00CONCRETE GUNITER/SHOTCRETER, DRY/SEMI-WET, 1.4 - 2.3 CY/HR, W/1 GAL HOPPER/ ROTARY PUMP/ 100' - 1.5" DIA HOSE/ NOZZLE/ & AIR COMPRESSOR

HP E

16AL 252C35AV009 $34,582 3.71 0.38 0.97 182.2412.42CONCRETE GUNITER/SHOTCRETER, DRY/SEMI-WET, 5 - 10 CY/HR, W/4.2 GAL HOPPER/ ROTARY PUMP/ 100' - 2.36" DIA HOSE/ NOZZLE/ & AIR COMPRESSOR

HP E

EP 1110-1-8, Vol. 430 Nov 11

2-67


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

C35 ALIVA LTD. (continued)26AL 262C35AV010 $64,468 6.91 0.71 1.58 274.1721.08CONCRETE GUNITER/SHOTCRETER,

WET/DRY, 9 - 13 CY/HR, W/4.2 GAL HOPPER/ ROTARY PUMP/ 100' - 2.36" DIA HOSE/ NOZZLE/ & AIR COMPRESSOR

HP E

20AL 285C35AV006 $92,222 9.80 1.01 1.22 335.9127.71CONCRETE GUNITER/SHOTCRETER, WET/DRY, 11 - 27.5 CY/HR, W/6.6 GAL HOPPER/ ROTARY PUMP/ 100' - 2.55" DIA HOSE/ NOZZLE/ & AIR COMPRESSOR

HP E

12AL 302C35AV011 $51,055 5.47 0.56 0.73 503.3016.33CONCRETE GUNITER/SHOTCRETER, SHOTCRETE HYDRAULIC SPRAYER ARM, 25.6 ' HIGH (ADD TRUCK OR SMALL TRAILER & SHOTCRETE UNIT)

HP E

20AL 307C35AV012 $147,779 15.83 1.63 1.22 689.5542.65CONCRETE GUNITERS / SHOTCRETERS, SHOTCRETE HYDRAULIC SPRAYER ARM, 52.5' HIGH (ADD TRUCK OR SMALL TRAILER & SHOTCRETE UNIT)

HP E

CONCRETE MIXING UNITSC400.00 CONCRETE MIXING UNITSSUBCATEGORY

CEMEN TECH

10SCD2-50HC40CC001 $31,296 5.01 0.35 0.57 232.8611.74CONCRETE MIXERS, STATIONARY CONCRETE DISPENSER, 15 CY/HR, 2 - 4.5 CY MATERIAL CAPACITY

HP E

EP 1110-1-8, Vol. 430 Nov 11

2-68


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

MULTIQUIP, INC.

8WM 70SH8C40MU001 $3,657 0.55 0.04 1.82 80.323.31CONCRETE MIXERS, MIXER, PLASTER/MORTAR, 7 CF, TRAILER MTD

HP G

13WM 120SHHC40MU002 $7,422 1.15 0.08 2.96 110.665.92CONCRETE MIXERS, MIXER, PLASTER/MORTAR, 12 CF, TRAILER MTD

HP G

8MC 64SH8C40MU003 $3,606 0.54 0.04 1.82 70.313.30CONCRETE MIXERS, MIXER, CONCRETE, 6 CF, TRAILER MTD

HP G

8MC 94SH8C40MU004 $4,146 0.63 0.05 1.82 80.373.49CONCRETE MIXERS, MIXER, CONCRETE, 9 CF, TRAILER MTD

HP G


1CMS44EC40ST001 $2,271 0.33 0.03 0.03 50.201.01CONCRETE MIXERS, MIXER, CONCRETE, 4 CF, TRAILER MTD

HP E

6CMS44HC40ST002 $2,485 0.36 0.03 1.25 50.212.26CONCRETE MIXERS, MIXER, CONCRETE, 4 CF, TRAILER MTD

HP G


HP E


HP E


28EC40XX001 $3,634 0.58 0.04 0.11 70.331.63CONCRETE MIXERS, MIXER, PLASTER/MORTAR, 8 CF, ELECTRIC, PORTABLE

HP E

78GC40XX002 $3,886 0.62 0.04 1.59 70.353.15CONCRETE MIXERS, MIXER, PLASTER/MORTAR, 8 CF, GAS, PORTABLE

HP G

EP 1110-1-8, Vol. 430 Nov 11

2-69


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

C40 NO SPECIFIC MANUFACTURER (continued)310EC40XX003 $5,544 0.89 0.06 0.17 90.512.38CONCRETE MIXERS, MIXER,

PLASTER/MORTAR, 10 CF, ELECTRIC, PORTABLE

HP E


HP G


HP E


HP E


HP G

CONCRETE PAVING MACHINESC450.00 CONCRETE PAVING MACHINESSUBCATEGORY

GOMACO CORPORATION

36C-450C45GO026 $58,920 7.86 0.64 8.84 644.5729.26CONCRETE PAVING MACHINES, CYLINDER FINISHER, SINGLE DRUM, FINISHING WIDTH 9'-137'

HP G

50C-650-FC45GO027 $74,886 9.98 0.81 6.12 915.8031.24CONCRETE PAVING MACHINES, CYLINDER FINISHER, DOUBLE DRUM, FINISHING WIDTH 19'-51'

HP D-off

50C-650-SC45GO028 $119,162 15.89 1.29 6.12 1269.2445.65CONCRETE PAVING MACHINES, CYLINDER FINISHER, DOUBLE DRUM, FINISHING WIDTH 19'-51'

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-70


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

C45 GOMACO CORPORATION (continued)36C-750C45GO029 $79,215 10.56 0.86 8.84 916.1435.86CONCRETE PAVING MACHINES,

CYLINDER FINISHER, DOUBLE DRUM, FINISHING WIDTH 8'-156'

HP G

92GT-3200C45GO013 $136,497 18.20 1.48 11.26 13010.5857.06CONCRETE PAVING MACHINES, CURB/GUTTER SLIPFORM PAVER, CRAWLER, 3-TRACK, 36" WIDE MOLD/FORM

HP D-off

92COMMANDER II /GT6200

C45GO010 $164,501 21.93 1.79 11.26 20012.7666.17CONCRETE PAVING MACHINES, CURB/GUTTER SLIPFORM PAVER, CRAWLER, 2-TRACK, 36'' WIDE MOLD/FORM

HP D-off

98GT-3600C45GO014 $188,180 25.09 2.04 12.00 21014.5974.70CONCRETE PAVING MACHINES, CURB/GUTTER SLIPFORM PAVER, CRAWLER, 3-TRACK, 24'' WIDE MOLD/FORM

HP D-off

185COMMANDER III/GT6300

C45GO011 $253,408 33.79 2.75 22.64 30019.65107.89CONCRETE PAVING MACHINES, CURB/GUTTER SLIPFORM PAVER, CRAWLER, 3-TRACK, 36'' WIDE MOLD/FORM

HP D-off

169COMMANDER IIIC45GO012 $339,493 45.27 3.69 20.69 36926.33133.71CONCRETE PAVING MACHINES, CURB/GUTTER SLIPFORM PAVER, CRAWLER , 4-TRACK, 36'' WIDE MOLD/FORM

HP D-off

230GP-2600C45GO016 $371,120 49.48 4.03 28.15 75028.77152.37CONCRETE PAVING MACHINES, SLIPFORM PAVER, CRAWLER, 2-TRACK, 24'-32' PAVING WIDTH

HP D-off

335GHP-2800C45GO018 $462,997 61.73 5.03 41.00 70035.90196.71CONCRETE PAVING MACHINES, SLIPFORM PAVER, CRAWLER, 2-TRACK, 24'-32' PAVING WIDTH

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-71


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

C45 GOMACO CORPORATION (continued)450GP-4000C45GO020 $549,059 73.21 5.96 55.08 88042.57240.53CONCRETE PAVING MACHINES,

SLIPFORM PAVER, CRAWLER, 2-TRACK, 12'-50' PAVING WIDTH

HP D-off

3859500C45GO031 $449,425 59.92 4.88 47.12 72934.84199.16CONCRETE PAVING MACHINES, TRIMMER/PLACER, W/16'-8'' TRIMMER HEAD

HP D-off

MILLER SPREADER CO.

15MC 650C45MJ001 $8,545 1.14 0.09 3.68 80.666.98CONCRETE PAVING MACHINES, CURB BUILDER, SLIPFORM PAVER, 6.1 CF HOPPER 6" AUGER

HP G

M-B-W, INC.

26C101C45MW00 $49,360 6.52 0.54 3.18 273.8019.60CONCRETE PAVING MACHINES, CURB ONLY SLIPFORM PAVER, RUBBER TIRED, 12"

HP D-off

26CG200C45MW00 $62,685 8.27 0.68 3.18 344.8223.92CONCRETE PAVING MACHINES, CURB/GUTTER SLIPFORM PAVER, RUBBER TIRED, 48"

HP D-off

CONCRETE PUMPSC550.00 CONCRETE PUMPSSUBCATEGORY

MAYCO PUMP - MULTIQUIP INC.

46C-30HDGC55M3001 $24,450 2.71 0.24 10.46 271.6018.27CONCRETE PUMP, 25 CY/HR, SINGLE, TRAILER MTD

HP G

60LS-400C55M3002 $54,854 6.17 0.54 6.94 423.6322.04CONCRETE PUMP, 45 CY/HR, SINGLE, TRAILER MTD

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-72


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

C55 MAYCO PUMP - MULTIQUIP INC. (continued)

106LS-600C55M3003 $64,507 7.26 0.64 12.25 474.2730.51CONCRETE PUMP, 70 CY/HR, SINGLE, TRAILER MTD

HP D-off

OLIN ENGINEERING, INC.

7410 22C55OE006 $51,872 5.80 0.51 8.55 443.4123.06CONCRETE PUMP, 22 CY/HR,TRAILER MTD (OPEN LOOP HYDRAULIC SYSTEM)

HP D-off

12720 80C55OE009 $97,966 10.95 0.97 14.68 726.4541.90CONCRETE PUMP, 76 CY/HR, TRAILER MTD TANDEM (CLOSED LOOP HYDRAULIC SYSTEM)

HP D-off

18115 95C55OE011 $90,656 10.13 0.89 20.92 705.9647.01CONCRETE PUMP, 100 CY/HR, TRAILER MTD TANDEM (OPEN LOOP HYDRAULIC SYSTEM)

HP D-off

18120 100C55OE012 $115,100 12.88 1.13 20.92 817.5753.35CONCRETE PUMP, 100 CY/HR, TRAILER MTD TANDEM (CLOSED LOOP HYDRAULIC SYSTEM)

HP D-off

4Z 26XC55OE001 $275,031 30.94 2.71 0.00 10018.1871.40CONCRETE PUMP, PUMP & BOOM, 130 CY/HR, REACH: 72' HORIZONTAL / 85' VERTICAL (ADD 50,000 GVW TRUCK)

4Z 36XC55OE002 $353,116 39.73 3.48 0.00 10023.3591.68CONCRETE PUMP, PUMP & BOOM, 182 CY/HR, REACH: 104' HORIZONTAL / 118' VERTICAL (ADD 50,000 GVW TRUCK)

5RZ 47IC55OE003 $537,681 60.49 5.30 0.00 10035.55139.59CONCRETE PUMP, PUMP & BOOM, 182 CY/HR, REACH: 134' HORIZONTAL / 152' VERTICAL (ADD 50,000 GVW TRUCK)

EP 1110-1-8, Vol. 430 Nov 11

2-73


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

SCHWING AMERICA INC.

80SP750-18C55SC001 $79,767 8.93 0.79 9.25 695.2631.08CONCRETE PUMP, 70 CY/HR, 1,100 PSI, TRAILER MTD

HP D-off

197SP2800C55SC002 $138,759 15.47 1.37 22.77 1159.1161.54CONCRETE PUMP, 76 CY/HR, 1,565 PSI, TRAILER MTD

HP D-off

210S 28XC55SC005 $460,521 51.32 4.54 27.85 35930.20150.80CONCRETE PUMP, 117 CY/HR, 75' BOOM, TRUCK MTD

HP D-on

210KVM 32XGC55SC006 $496,538 55.37 4.89 27.85 47032.58160.14CONCRETE PUMP, 117 CY/HR, 92' BOOM, TRUCK MTD

HP D-on

CONCRETE SAWS (Add cost for sawblade wear)C600.00 CONCRETE SAWS (Add cost for sawblade wear)SUBCATEGORY

CUSHION CUT, INC. (HUSQVARNA)

66FS 6600 D 18C60CQ011 $22,966 3.44 0.24 9.65 191.9619.15CONCRETE SAW, 6.5" DEPTH, SELF PROPELLED, 14" BLADE (ADD COST FOR SAWBLADE WEAR & WATER)

HP D-off

9FS 9BC60CQ002 $3,006 0.45 0.03 2.63 20.264.03CONCRETE SAW, 5.625" DEPTH, MANUAL, 16" BLADE (ADD COST FOR SAWBLADE WEAR & WATER)

HP G

13FS 13BUCC60CQ003 $3,237 0.49 0.03 3.80 20.285.45CONCRETE SAW, 5.625" DEPTH, MANUAL, 16" BLADE (ADD COST FOR SAWBLADE WEAR & WATER)

HP G

35FS 3500 G 18C60CQ001 $13,301 2.00 0.14 10.23 101.1416.24CONCRETE SAW, 6.5" DEPTH, SELF-PROPELLED, 18" BLADE (ADD COST FOR SAWBLADE WEAR & WATER)

HP G

30FS 3500 E 26C60CQ014 $14,299 2.14 0.15 2.19 91.228.19CONCRETE SAW, 10.625" DEPTH, SELF PROPELLED, 26" BLADE (ADD COST FOR SAWBLADE WEAR & WATER)

HP E

EP 1110-1-8, Vol. 430 Nov 11

2-74


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

C60 CUSHION CUT, INC. (HUSQVARNA) (continued)


HP D-off

35FS 3500 G 30C60CQ010 $13,769 2.07 0.14 10.23 121.1816.40CONCRETE SAW, 12.125" DEPTH, SELF PROPELLED, 30" BLADE,W/TRANSAXLE (ADD COST FOR SAWBLADE WEAR & WATER)

HP G


HP D-off

84FS 8400/36C60CQ016 $29,315 4.40 0.30 12.28 202.5024.40CONCRETE SAW, 14.875" DEPTH, SELF PROPELLED, 36" BLADE (ADD COST FOR SAWBLADE WEAR & WATER)

HP D-off

FELKER (TARGET)

2S80/14ZC60FE002 $1,552 0.23 0.02 0.58 10.141.19CONCRETE SAW, 5.00" DEPTH, MANUAL, 14" BLADE (ADD COST FOR SAWBLADE WEAR & WATER)

HP G

9ES 1409C60FE006 $3,240 0.49 0.03 2.63 20.284.11CONCRETE SAW, 4.625" DEPTH, WALK BEHIND, 14" BLADE (ADD COST FOR SAWBLADE WEAR & WATER)

HP G

13ES 1413C60FE007 $3,392 0.51 0.03 3.80 20.295.50CONCRETE SAW, 4.625" DEPTH, WALK BEHIND, 14" BLADE (ADD COST FOR SAWBLADE WEAR & WATER)

HP G

20ECII20HC60FE009 $10,834 1.63 0.11 5.85 60.9310.40CONCRETE SAW, 7.50" DEPTH, SELF PROPELLED, 20" BLADE (ADD COST FOR SAWBLADE WEAR & WATER)

HP G

EP 1110-1-8, Vol. 430 Nov 11

2-75


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

BOART LONGYEAR COMPANY

13FS 13BC60LY005 $3,182 0.48 0.03 3.80 20.275.43CONCRETE SAW, 7.00" DEPTH, WALK BEHIND(ADD COST FOR SAWBLADE WEAR & WATER)

HP G

10360-10APC60LY001 $27,713 4.16 0.28 2.92 22.3612.84CONCRETE SAW, RAIL SAW, 15.50" DEPTH, WALL (ADD COMPRESSOR & COST FOR SAWBLADE WEAR & WATER)

HP G

35360-35HMC60LY002 $40,984 6.15 0.42 10.23 23.5025.74CONCRETE SAW, RAIL SAW, 24.50" DEPTH, WALL(ADD COST FOR SAWBLADE WEAR & WATER)

HP G

32WR-400C60LY011 $79,214 11.88 0.81 4.68 156.7532.65CONCRETE SAW, WIRE SAW SYSTEM, HEAVY DUTY (ADD COST FOR SAW WIRE WEAR & WATER)

HP D-off

CONCRETE VIBRATORSC650.00 CONCRETE VIBRATORSSUBCATEGORY


1SV-1 115VC65ST007 $982 0.22 0.01 0.05 10.121.02CONCRETE VIBRATOR, 1.375" HEAD, 21' SHAFT (ADD 2KV GENERATOR)

HP E

2SV-2 115VC65ST008 $1,025 0.23 0.01 0.11 10.131.15CONCRETE VIBRATOR, 2.175" HEAD, 21' SHAFT (ADD 2KV GENERATOR)

HP E

3SV-3 115VC65ST009 $1,213 0.27 0.01 0.16 10.151.41CONCRETE VIBRATOR, 2.625" HEAD, 21' SHAFT (ADD 2KV GENERATOR)

HP E

6G55HC65ST013 $2,238 0.50 0.02 1.17 20.273.51CONCRETE VIBRATOR, 2.325" HEAD, 21' SHAFT, W/GAS MOTOR ON CART

HP G

EP 1110-1-8, Vol. 430 Nov 11

2-76


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

WACKER CORPORATION

5A 5000C65WC00 $2,042 0.46 0.02 1.06 10.253.19CONCRETE VIBRATOR, 1.75" HEAD, 13' SHAFT, W/GAS MOTOR ON CART

HP G

3M 3000C65WC00 $1,078 0.24 0.01 0.16 10.131.42CONCRETE VIBRATOR, 1.75" HEAD, 13' SHAFT, HI-FREQ INTERNAL (ADD 2KV GENERATOR)

HP E

2IREN 57C65WC00 $1,673 0.38 0.02 0.11 10.211.93CONCRETE VIBRATOR, 2.50" HEAD, 16.5' SHAFT, HI-FREQ INTERNAL (ADD 2KV GENERATOR)

HP E

CRANES, HYDRAULIC, SELF-PROPELLEDC750.00 CRANES, HYDRAULIC, SELF-PROPELLEDSUBCATEGORY

BRODERSON MANUFACTURING CORPORATION

38IC-20-1FC75BD007 $61,872 3.70 0.60 9.33 632.4519.01CRANES, HYDRAULIC, SELF-PROPELLED, YARD, 2.5 TON, 15' BOOM, 4X2

HP G

42IC-35-2CC75BD008 $82,260 4.94 0.80 10.31 783.2722.83CRANES, HYDRAULIC, SELF-PROPELLED, YARD, 4.0 TON, 19.2' BOOM, 4X2

HP G

42IC-35-2CC75BD004 $85,670 5.16 0.83 10.31 793.4123.23CRANES, HYDRAULIC, SELF-PROPELLED, YARD, 4.0 TON, 19' BOOM, 4X2, NON-ROTATING OPERATOR'S CAB

HP G

69IC-80-3GC75BD009 $111,198 6.64 1.08 16.94 1724.4034.42CRANES, HYDRAULIC, SELF-PROPELLED, YARD, 8.5 TON, 30' BOOM, 4X2

HP G

69IC-80-1GC75BD005 $107,650 6.42 1.05 16.94 1634.2633.95CRANES, HYDRAULIC, SELF-PROPELLED, YARD, 9.0 TON, 20' BOOM, 4X2, NON-ROTATING OPERATOR'S CAB

HP G

110IC-200-3FC75BD006 $157,202 9.35 1.53 27.00 3086.2152.23CRANES, HYDRAULIC, SELF-PROPELLED, YARD, 15.0 TON, 50' BOOM, 4X2, NON-ROTATING OPERATOR'S CAB

HP G

EP 1110-1-8, Vol. 430 Nov 11

2-77


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

C75 BRODERSON MANUFACTURING CORPORATION (continued)

85IC-250-3AC75BD010 $185,759 11.09 1.81 10.40 3847.3636.99CRANES, HYDRAULIC, SELF-PROPELLED, YARD, 18.0 TON, 50' BOOM, 4X4

HP D-off

130RT-300-2BC75BD011 $246,734 14.69 2.40 15.91 4739.7552.52CRANES, HYDRAULIC, SELF-PROPELLED, YARD, 15.0 TON, 60' BOOM, 4X4, 20'0" OFFSET

HP D-off

GROVE CRANES (MANITOWOC)

62YB4410C75GV021 $124,154 7.42 1.21 15.22 1734.9234.21CRANES, HYDRAULIC, SELF-PROPELLED, YARD, 10 TON, 30' BOOM, 4X4, NON-ROTATING OPERATOR'S CAB

HP G

110YB4415XTC75GV022 $153,885 9.15 1.50 13.46 3136.0836.28CRANES, HYDRAULIC, SELF-PROPELLED, YARD, 15 TON, 52' BOOM, 4X4, NON-ROTATING OPERATOR'S CAB

HP D-off

152RT525EC75GV028 $289,403 16.69 2.82 18.60 50011.1764.93CRANES, HYDRAULIC, SELF-PROPELLED, ROUGH TERRAIN, 25 TON, 75' BOOM, 4X4

HP D-off


HP D-off

173RT640EC75GV024 $459,041 26.94 4.47 21.18 65017.9491.73CRANES, HYDRAULIC, SELF-PROPELLED, ROUGH TERRAIN, 40 TON, 105' BOOM 4X4

HP D-off


HP D-off

240RT760C75GV014 $525,113 29.91 5.11 29.38 90920.07117.56CRANES, HYDRAULIC, SELF-PROPELLED, ROUGH TERRAIN, 60 TON, 110' BOOM, 4X4, W/HOOK BLOCK & BALL

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-78


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

C75 GROVE CRANES (MANITOWOC) (continued)

250RT875CC75GV025 $835,361 48.75 8.13 30.60 1,09132.51159.09CRANES, HYDRAULIC, SELF-PROPELLED, ROUGH TERRAIN, 70 TON, 110' BOOM 4X4

HP D-off

250RT875 BXLC75GV020 $840,247 47.91 8.18 30.60 1,11932.14169.15CRANES, HYDRAULIC, SELF-PROPELLED, ROUGH TERRAIN, 90 TON, 138' BOOM, 4X4

HP D-off

300RT9130EC75GV016 $1,197,893 69.63 11.66 36.72 1,36446.48223.48CRANES, HYDRAULIC, SELF-PROPELLED, ROUGH TERRAIN, 100 TON, 160' BOOM, 4X4, W/HOOK BLOCK & BALL

HP D-off

PETTIBONE MICHIGAN LLC

18540RSC75PB002 $484,316 28.49 4.71 22.64 49618.9692.87CRANES, HYDRAULIC, SELF-PROPELLED, ROUGH TERRAIN, 20 TON, 64.1' BOOM, 4X4X4

HP D-off

TADANO AMERICA CORPORATION

180TR-300XL-4C75TD003 $389,782 22.87 3.79 22.03 53715.2382.51CRANES, HYDRAULIC, SELF-PROPELLED, ROUGH TERRAIN, 30 TON, 112' BOOM, 4X4

HP D-off


HP D-off


HP D-off

TEREX CORPORATION

130RT230C75TE001 $366,774 21.96 3.57 15.91 56314.5568.54CRANES, HYDRAULIC, SELF-PROPELLED, ROUGH TERRAIN, 30 TON, 94' BOOM, 4X4

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-79


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

C75 TEREX CORPORATION (continued)152RT335/40C75TE002 $504,315 30.12 4.91 18.60 63419.9791.04CRANES, HYDRAULIC, SELF-PROPELLED,

ROUGH TERRAIN, 40 TON, 94' BOOM, 4X4

HP D-off

CRANES, HYDRAULIC, TRUCK MOUNTEDC800.01 UNDER 26 TONSUBCATEGORY

TEREX CORPORATION

130CD225C80TE008 $292,555 17.08 2.85 13.70 52511.3955.10CRANES, HYDRAULIC, TRUCK MTD, ROUGH TERRAIN, 25 TON, 72' BOOM, 4X4

HP D-off


2451700C80XX001 $148,676 8.78 1.45 25.82 3305.8448.18CRANES, HYDRAULIC, TRUCK MTD, BOOM TRUCK, 17 TON, 80' BOOM, 4X2

HP D-off

3002300C80XX002 $196,267 11.52 1.91 31.62 6007.6760.96CRANES, HYDRAULIC, TRUCK MTD, BOOM TRUCK, 23.5 TON, 102' BOOM, 6X2

HP D-off

0.02 26 TON THRU 65 TONSUBCATEGORY


300TMS-500EC80GV025 $463,756 24.41 4.48 31.62 54016.6987.32CRANES, HYDRAULIC, TRUCK MTD, 40 TON, 95' BOOM, 6X4

HP D-off

400TMS-700EC80GV006 $710,186 37.43 6.85 42.16 77125.57126.45CRANES, HYDRAULIC, TRUCK MTD, 50 TON, 110' BOOM, 8X4

HP D-off

400TMS750EC80GV029 $709,881 37.21 6.85 42.16 94725.46127.31CRANES, HYDRAULIC, TRUCK MTD, 50 TON, 110' BOOM, 8X4X4

HP D-off

348GMK 3050C80GV026 $700,210 36.77 6.76 36.68 74525.15119.80CRANES, HYDRAULIC, TRUCK MTD, ALL TERRAIN, 55 TON, 125' BOOM, 8X4

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-80


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

C80 GROVE CRANES (MANITOWOC) (continued)

400TMS760EC80GV030 $711,092 37.27 6.86 42.16 94925.50127.44CRANES, HYDRAULIC, TRUCK MTD, 60 TON, 110' BOOM, 8X4X4

HP D-off

LINK-BELT CONSTRUCTION EQUIPMENT CO.

365HTC-8640 SLC80LB009 $595,488 31.27 5.75 38.47 57521.39110.05CRANES, HYDRAULIC, TRUCK MTD, 40 TON, 105' BOOM, 6X4X2

HP D-off

365HTC-8660 IIC80LB011 $603,769 31.57 5.83 38.47 83121.62111.50CRANES, HYDRAULIC, TRUCK MTD, 60 TON, 110' BOOM, 8X4X4

HP D-off

TEREX CORPORATION

250T335/40C80TE002 $372,653 19.48 3.60 26.35 49313.3471.76CRANES, HYDRAULIC, TRUCK MTD, ALL TERRAIN, 40 TON, 94' BOOM, 6X4

HP D-off

370T 500C80TE003 $491,485 25.63 4.74 39.00 80617.5699.62CRANES, HYDRAULIC, TRUCK MTD, ALL TERRAIN, 50 TON, 110' BOOM, 8X4

HP D-off

0.03 66 TON THRU 125 TONSUBCATEGORY


400TMS-870C80GV020 $858,193 40.17 8.24 42.16 9,16128.33138.82CRANES, HYDRAULIC, TRUCK MTD, 70 TON, 110' BOOM, 8X4

HP D-off

400TMS875CC80GV031 $805,604 37.59 7.74 42.16 81726.54133.75CRANES, HYDRAULIC, TRUCK MTD, 75 TON, 110' BOOM, 8X4X4

HP D-off

422GMK4090C80GV032 $1,073,307 49.62 10.31 44.48 1,18435.12172.65CRANES, HYDRAULIC, TRUCK MTD, ALL TERRAIN, 80 TON, 142' BOOM, 8X6X8

HP D-off


121ATF-650XLC80TD001 $747,677 34.24 7.18 19.56 1,09024.30105.48349 HP D-onCRANES, HYDRAULIC, TRUCK MTD, ALL TERRAIN, 65 TON, 132' BOOM, 8X8

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-81


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

C80 TADANO AMERICA CORPORATION (continued)

158ATF-1000XLC80TD002 $933,142 43.00 8.96 23.96 1,07030.46129.65375 HP D-onCRANES, HYDRAULIC, TRUCK MTD, ALL TERRAIN, 100 TON, 138' BOOM, 8X8

HP D-off

0.04 OVER 125 TONSUBCATEGORY


174GMK 5240C80GV013 $2,106,692 88.33 20.13 30.04 1,18064.30259.60600 HP D-onCRANES, HYDRAULIC, TRUCK MTD, ALL TERRAIN, 125 TON, 197' BOOM, 10X8

HP D-off


HP D-off


HP D-off


HP D-off


533ATF-1500XLC80TD005 $1,119,999 46.40 10.70 65.99 1,33033.90192.89503 HP D-onCRANES, HYDRAULIC, TRUCK MTD, ALL TERRAIN, 150 TON, 162' BOOM, 10X8

HP D-off

CRANES, MECHANICAL, LATTICE BOOM, CRAWLER MOUNTEDC850.12 DRAGLINE, CLAMSHELL, OVER 1.0 CY THRU 2.5 CYSUBCATEGORY


284138 HSLC85LB019 $831,900 41.60 8.35 25.11 1,39029.15126.81CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, DRAGLINE/CLAMSHELL, 80 TON, 100' BOOM (ADD BUCKET)

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-82


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

TEREX CORPORATION

1505220C85TE001 $665,305 33.27 6.67 13.26 83123.3193.57CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, DRAGLINE/CLAMSHELL, 50 TON, 100' BOOM (ADD BUCKET)

HP D-off

2507225C85TE002 $925,366 46.27 9.28 22.10 1,25932.42134.34CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, DRAGLINE/CLAMSHELL, 85 TON, 100' BOOM (ADD BUCKET)

HP D-off

0.13 DRAGLINE, CLAMSHELL, OVER 2.5 CY THRU 5.0 CYSUBCATEGORY


284238 HYLAB 5C85LB021 $1,315,096 58.45 13.11 25.11 3,35742.34174.43CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, DRAGLINE/CLAMSHELL, 150 TON, 100' BOOM (ADD BUCKET)

HP D-off

MANITOWOC ENGINEERING CO.

340777C85MA002 $1,435,096 63.78 14.31 30.06 3,81546.20193.26CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, DRAGLINE/CLAMSHELL, 5.0 CY, 130' BOOM (ADD BUCKET)

HP D-off

TEREX CORPORATION

3359225C85TE003 $1,164,383 51.75 11.61 29.61 2,48237.49162.53CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, DRAGLINE/CLAMSHELL, 150 TON, 100' BOOM (ADD BUCKET)

HP D-off

0.14 DRAGLINE, CLAMSHELL, OVER 5.0 CYSUBCATEGORY


400999C85MA003 $2,084,545 83.38 20.68 35.36 5,10062.37261.98CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, DRAGLINE/CLAMSHELL, 7.0 CY, 140' BOOM (ADD BUCKET)

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-83


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

0.22 LIFTING, 26 TON THRU 50 TONSUBCATEGORY

KOBELCO AMERICA INC.

178CK550C85KC007 $610,822 27.15 6.09 11.50 1,00119.6773.37CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, 50 TON, 30' BOOM, LIFTING

HP D-off


197108 HYLAB 5C85LB024 $592,735 26.34 5.91 12.73 96819.0872.90CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, 50 TON, 70' BOOM, LIFTING

HP D-off

0.23 LIFTING, 51 TON THRU 150 TONSUBCATEGORY



HP D-off


HP D-off

265CK1000C85KC003 $1,045,384 44.43 9.99 17.12 1,89932.21121.44CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, 100 TON, 200' BOOM, LIFTING

HP D-off


207138 HSLC85LB001 $760,729 32.33 7.27 13.37 1,46423.4489.38CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, 80 TON, 40' TUBULAR BOOM, LIFTING

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-84


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

C85 LINK-BELT CONSTRUCTION EQUIPMENT CO. (continued)

284218 HSLC85LB014 $993,835 42.24 9.50 18.35 1,79030.62117.74CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, 110 TON, 230' BOOM, LIFTING

HP D-off

284238 HYLAB 5C85LB015 $1,373,775 58.39 13.13 18.35 3,35742.33155.05CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, 150 TON, 240' BOOM, LIFTING

HP D-off


340555C85MA008 $1,198,682 50.94 11.45 21.96 3,12136.92141.80CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, 100 TON, 260' BOOM, LIFTING

HP D-off


HP D-off

TEREX CORPORATION

184HC 80C85TE008 $697,877 29.66 6.67 11.89 1,43021.5081.58CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, 80 TON, 200' BOOM, LIFTING

HP D-off

230HC 110C85TE009 $859,956 36.55 8.22 14.86 1,91126.50100.76CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, 100 TON, 230' BOOM, LIFTING

HP D-off

240HC 125C85TE010 $1,142,000 48.54 10.91 15.50 2,12835.18129.15CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, 125 TON, 240' BOOM, LIFTING

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-85


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

0.24 LIFTING, OVER 150 TONSUBCATEGORY



HP D-off


HP D-off


284248 HYLAB 5C85LB016 $1,754,285 67.78 16.68 18.35 3,24250.57186.96CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, 200 TON, 280' BOOM, LIFTING

HP D-off



HP D-off


HP D-off

TEREX CORPORATION

315HC 210C85TE011 $1,684,810 65.09 16.02 20.35 3,70848.57182.57CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, 210 TON, 280' BOOM, LIFTING

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-86


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

CRANES, MECHANICAL, LATTICE BOOM, TRUCK MOUNTEDC900.04 OVER 125 TONSUBCATEGORY


200HC-238H IIC90LB001 $1,557,274 61.28 15.45 25.00 1,91346.09194.42445 HP D-onCRANES, MECHANICAL, LATTICE BOOM, TRUCK MTD, 150 TON, 260' BOOM, 8X4

HP D-off

445HC-278 H IIC90LB003 $2,880,620 113.71 28.58 44.99 3,38585.44353.81445 HP D-onCRANES, MECHANICAL, LATTICE BOOM, TRUCK MTD, 300 TON, 330' BOOM, 12X6

HP D-off

CRANES, TOWERC950.00 CRANES, TOWERSUBCATEGORY

PECCO AND WOLFF TOWER CRANES (MORROW)

128SK200C95AP004 $534,361 23.75 5.33 6.74 97017.2170.94TOWER CRANE 3.4 TON @ 181' RADIUS 42.6' HEIGHT (ADD 95KW GENERATOR & T-SECTION)

HP E

S16-35 TOWER SECTION

C95AP005 $17,039 0.76 0.17 0.00 160.551.80TOWER CRANE OPTION, 1.1' T-TRANSITION S35 -S16 (ADD SK 140 - SK 225 TOWER CRANE)

S35 TOWER SECTION

C95AP006 $32,296 1.44 0.32 0.00 891.043.42TOWER CRANE OPTION, 19.33' TOWER SECTION (ADD TO SK 140 - SK 400 TOWER CRANE)

213SK400C95AP007 $843,730 37.50 8.41 11.21 1,78327.16111.56TOWER CRANE, 3.3 TON @ 245' RADIUS, 56.7' HEIGHT (ADD 160 KW GENERATOR & T-SECTION)

HP E

EP 1110-1-8, Vol. 430 Nov 11

2-87


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

C95 PECCO AND WOLFF TOWER CRANES (MORROW) (continued)

S35 CLIMBING UNIT

C95AP008 $130,661 5.81 1.30 0.00 2484.2114.31TOWER CRANE OPTION, 29.2' CLIMBING UNIT (ADD TO SK 200 - SK 400 TOWER CRANE)

S35-60 TOWER SECTION

C95AP009 $43,492 1.93 0.43 0.00 991.404.59TOWER CRANE OPTION, 19.4' T-TRANSITION S60 S35 (ADD SK 225 - SK 560 TOWER CRANE)

217SK560C95AP010 $1,128,092 50.14 11.25 11.43 1,55736.32141.97TOWER CRANE, 2.8 TON @ 265' RADIUS, 76.5' HEIGHT (ADD 161 KW GENERATOR &T-SECTION)

HP E

S60 TOWER SECTION


S60 CLIMB UNITC95AP012 $162,875 7.24 1.62 0.00 2585.2417.71TOWER CRANE OPTION, 32.8' CLIMBING UNIT (ADD TO SK 225 - SK 560 TOWER CRANE)

354SN355C95AP013 $1,075,757 47.81 10.72 18.64 2,74834.63147.60TOWER CRANE, 3.8 TON @ 197' RADIUS, 110' TALL, LUFFING (ADD 300 KW GENERATOR & T-SECTION)

HP E

SN35 TOWER SECTION

C95AP014 $36,997 1.64 0.37 0.00 891.193.91TOWER CRANE OPTION, 14.75' TOWER SECTION (ADD TO SN 141 - SN 355 TOWER CRANE)

SN35 CLIMBING UNIT

C95AP015 $142,080 6.31 1.42 0.00 2484.5815.52TOWER CRANE OPTION, 29.2' CLIMBING UNIT (ADD TO SN 141 - SN 355 TOWER CRANE)

S35N-60TOWER SECTION

C95AP016 $49,678 2.21 0.50 0.00 991.615.26TOWER CRANE OPTION, 19.4' T-TRANSITION S60 S35N (ADD SN 141 - SK 355 TOWER CRANE)

EP 1110-1-8, Vol. 430 Nov 11

2-88


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

C95 PECCO AND WOLFF TOWER CRANES (MORROW) (continued)

125SK140C95AP017 $454,682 20.21 4.53 6.58 1,30914.6461.27TOWER CRANE, 3.1 TON @ 151' RADIUS, 85.0' HEIGHT (ADD 95KW GENERATOR & T-SECTION)

HP E

S16 TOWER SECTION


S16 CLIMBING UNIT

C95AP019 $88,343 3.93 0.88 0.00 1652.859.84TOWER CRANE OPTION, 29.2' CLIMBING UNIT (ADD TO SK140 - SK 200 TOWER CRANE)

223SN141C95AP020 $502,085 22.31 5.00 11.74 1,08216.1674.27TOWER CRANE, 1.6 TON @ 147' RADIUS, 89' TALL, LUFFING (ADD 200 KW GENERATOR & T-SECTION)

HP E

258SN160-16C95AP021 $786,729 34.97 7.84 13.58 1,17925.33108.22TOWER CRANE, 2.8 TON @ 164' RADIUS, 88' TALL, LUFFING (ADD 250 KW GENERATOR & T-SECTION)

HP E

24PH5000-12C95AP022 $119,716 5.32 1.19 1.26 1303.8515.60TOWER CRANE OPTION, 24 PERSON / 2.4 TON MATERIAL ELEVATOR/HOIST (ADD 4.9' MAST SECTION & 18 KW GENERATOR)

HP E

MAST SECTIONC95AP023 $2,826 0.13 0.03 0.00 30.100.30TOWER CRANE OPTION, 4.9' MAST-> PERSON/MATERIAL ELEVATOR/HOIST (ADD WALL TIE & CABLE GUIDE @30')

EP 1110-1-8, Vol. 430 Nov 11

2-89


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

MORROW EQUIPMENT COMPANY, LLC

3597KC95LH022 $412,399 18.16 4.11 1.84 1,59313.1948.85TOWER CRANE, HORIZONTAL BOOM, JIB CRANE, 13.2 TON MAX, 1.9 TON @ 148' RADIUS, 66' HEIGHT, SELF/ERECTING, W/FIVE - 7' 10" TOWER SECTIONS/ & ROAD TRANSPORT EQUIPMENT (ADD 40KW GENERATOR)

HP E

109132 HCC95LH003 $465,599 20.69 4.64 5.74 1,15614.9961.10TOWER CRANE, HORIZONTAL BOOM, JIB CRANE, 8.8 TON MAX, 2.4 TON @ 168' RADIUS, 147.8' HEIGHT, W/FOURTEEN - 8' 2" TOWER SECTIONS (ADD 85 KW GENERATOR)

HP E

148200 HCC95LH005 $606,005 26.93 6.04 7.79 1,37419.5180.12TOWER CRANE, HORIZONTAL BOOM, JIB CRANE, 11.0 TON MAX, 2.5 TON @ 201' RADIUS, 162.7' HEIGHT, W/NINE - 13' 7" TOWER SECTIONS (ADD 110 KW GENERATOR)

HP E

223390 HCC95LH011 $1,131,703 50.30 11.28 11.74 2,74436.43142.82TOWER CRANE, HORIZONTAL BOOM, JIB CRANE, 17.6 TON MAX, 3.3 TON @ 246' RADIUS, 199.1' HEIGHT, W/NINE - 19' 0" TOWER SECTIONS (ADD 170 KW GENERATOR)

HP E

223550 HC20C95LH013 $1,444,766 64.21 14.40 11.74 3,76546.51175.90TOWER CRANE, HORIZONTAL BOOM, JIB CRANE, 22.0 TON MAX, 3.8 TON @ 265' RADIUS, 237.5' HEIGHT, W/TWELVE - 19' 0" TOWER SECTIONS (ADD 170 KW GENERATOR)

HP E

317550 HC-LC95LH015 $1,925,420 85.57 19.19 16.69 5,07561.98236.38TOWER CRANE, 26.4 TON MAX, 3/4 TON @ 197' RADIUS, 210' HEIGHT, LUFFING, W/SIX 19' 0" TOWER SECTIONS (ADD 480 KW GENERATOR)

HP E

EP 1110-1-8, Vol. 430 Nov 11

2-90


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

DRILLS, HYDRAULIC TRACK (Add cost for drill steel and bit wear)D100.10 DRILLS, AIR TRACK (Add cost for drill steel and bit wear)SUBCATEGORY

INGERSOLL RAND ROCK DRILL DIV

750ECM350/VL140D10IR003 $182,858 9.80 1.91 0.00 1296.8126.82DRILL, AIR TRACK, CRAWLER, 2.5-4.0" DIA, 12' FEED (ADD COST FOR DRILL STEEL AND BIT WEAR, ADD 750 CFM COMPRESSOR)

CFM A

SULLIVAN-PALATEK, INC.

750RAM EXT, VCR360

D10SU002 $225,238 12.07 2.36 0.00 1528.4032.86DRILL, AIR TRACK, CRAWLER, 2.5-4.0" DIA, 12' FEED (ADD COST FOR DRILL STEEL AND BIT WEAR, ADD 750 CFM COMPRESSOR)

CFM A

900RAM EXT, VCR361

D10SU003 $230,706 12.36 2.41 0.00 2058.5933.63DRILL, AIR TRACK, CRAWLER, 3.0-4.0" DIA, 12' FEED (ADD COST FOR DRILL STEEL AND BIT WEAR, ADD 900 CFM COMPRESSOR)

CFM A

0.20 DRILLS, HYDRAULIC TRACK (Add cost for drill steel and bit wear)SUBCATEGORY

INGERSOLL RAND ROCK DRILL DIV

215ECM590/YH80AD10IR005 $492,077 36.91 5.25 27.78 24523.71127.30DRILL, HYDRAULIC TRACK, CRAWLER, 2.5-4.5" DIA, 14' DRIFTER TRAVEL, SELF-CONTAINED (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

SULLIVAN-PALATEK, INC.

260SCORPION VCR360

D10SU005 $250,654 18.80 2.67 33.59 26512.0786.68DRILL, HYDRAULIC TRACK, CRAWLER, 5.25" DIA, 12' FEED (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-91


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

D10 SULLIVAN-PALATEK, INC. (continued)260SCORPION

VCR361D10SU006 $253,686 19.03 2.71 33.59 26512.2387.28DRILL, HYDRAULIC TRACK, CRAWLER,

6.5" DIA, 12' FEED (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

DRILLS, HORIZONTALD150.10 DRILLS, HORIZONTAL BORING & GROUND PIERCING (Add cost for drill steel and bit wear)SUBCATEGORY

BOR-IT MANUFACTURING COMPANY INC.

1212 MIGHT MAXD15BI001 $16,960 1.27 0.18 3.12 180.826.68DRILL, HORIZONTAL BORING, 12" DIA, COMBINED HEAD 28,000 LBS THRUST, W/100' AUGER TRACK (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP G

2020 POWER HOUSE II

D15BI002 $30,414 2.28 0.32 2.58 151.468.50DRILL, HORIZONTAL BORING, 20" DIA, COMBINED HEAD 44,000 LBS THRUST, W/100' AUGER TRACK (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

3024 BRUTED15BI003 $46,000 3.45 0.49 3.88 382.2212.84DRILL, HORIZONTAL BORING, 24" DIA, COMBINED HEAD 84,000 LBS THRUST, W/100' AUGER TRACK (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

4530 POWER PLUS


HP D-off

6236 WORKHORSE


HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-92


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

D15 BOR-IT MANUFACTURING COMPANY INC. (continued)

11948 TERMINATOR


HP D-off

18954 TERMINATOR II

D15BI008 $190,963 14.32 2.04 24.42 2509.2062.65DRILL, HORIZONTAL BORING, 54" DIA, COMBINED HEAD 32,700,000 LBS THRUST, W/100' AUGER TRACK (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

18960D15BI007 $204,858 15.36 2.19 24.42 2509.8765.21DRILL, HORIZONTAL BORING, 60" DIA, COMBINED HEAD 1,100,000 LBS THRUST, W/100' AUGER TRACK (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off


MC-500HD15XX001 $9,328 0.70 0.10 0.00 100.451.72DRILL, HORIZONTAL BORING, 3" - 6" DIA, 15,000 LBS THRUST, HYDRAULIC MOTOR (ADD COST FOR DRILL STEEL AND BIT WEAR)

H-12/RM-12D15XX002 $14,044 1.05 0.15 0.00 120.682.59DRILL, HORIZONTAL BORING, 4" - 12" DIA, 24,000 LBS THRUST, HYDRAULIC MOTOR (ADD COST FOR DRILL STEEL AND BIT WEAR)

0.20 DRILLS, HORIZONTAL & DIRECTIONAL (Add cost for drill steel and bit wear)SUBCATEGORY

VERMEER MANUFACTURING CO.

26D6x6D15VE001 $48,382 3.63 0.52 3.36 322.3412.71DRILL, HORIZONTAL DIRECTIONAL, 2.25" DIA, 5,500 LB THRUST, W/150' OF RODS (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-93


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

D15 VERMEER MANUFACTURING CO. (continued)

47D9x13 IID15VE002 $82,740 6.21 0.88 6.07 633.9922.08DRILL, HORIZONTAL DIRECTIONAL, 2.5" DIA, 9,000 LB THRUST, W/300' OF RODS (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off


HP D-off


HP D-off


HP D-off


HP D-off


HP D-off

225D100x120 IID15VE008 $574,682 43.10 6.13 29.07 43527.68138.61DRILL, HORIZONTAL DIRECTIONAL, 5.0" DIA, 100,000 LB THRUST, W/300' OF RODS (ADD COST FOR DRILL STEEL AND BIT WEAR

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-94


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

D15 VERMEER MANUFACTURING CO. (continued)

6MX125D15VE009 $6,806 0.51 0.07 1.43 60.332.88DRILL, HORIZONTAL DIRECTIONAL, 500 GAL, DRILLING FLUID MIXING SYSTEM (ADD TRAILER COST)

HP G

22MX240D15VE010 $19,955 1.50 0.21 2.84 120.966.87DRILL, HORIZONTAL DIRECTIONAL, 750 GAL, DRILLING FLUID MIXING SYSTEM (ADD TRAILER COST)

HP D-off

22MX240D15VE011 $20,278 1.52 0.22 2.84 130.986.93DRILL, HORIZONTAL DIRECTIONAL, 1,000 GAL, DRILLING FLUID MIXING SYSTEM (ADD TRAILER COST)

HP D-off

28MX240 & MX125D15VE012 $41,941 3.15 0.45 3.55 812.0311.73DRILL, HORIZONTAL DIRECTIONAL, 1,500 GAL, DRILLING FLUID MIXING SYSTEM WITH TRAILER

HP D-off

DRILLS, CORE, COLUMN MOUNTED (Add cost for drill steel and bit wear)D200.00 DRILLS, CORE, COLUMN MOUNTED (Add cost for drill steel and bit wear)SUBCATEGORY

ACKER DRILL COMPANY INC.

81200-GD20AD007 $16,785 1.57 0.18 0.52 30.975.29DRILL, CORE, COLUMN MOUNTED, 12" DIA MAX CORE HOLE (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP E

CUSHION CUT, INC. (HUSQVARNA)

16HCD24/12D20CQ001 $15,749 1.48 0.17 4.16 50.919.43DRILL, CORE, COLUMN MOUNTED, 1"-24" BIT DIA (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP G

EP 1110-1-8, Vol. 430 Nov 11

2-95


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

DRILLS, CORE & DOWELLING (Add cost for drill steel and bit wear)D250.00 DRILLS, CORE & DOWELLING (Add cost for drill steel and bit wear)SUBCATEGORY

ACKER DRILL COMPANY INC.

28ACE WD25AD004 $84,642 6.35 0.90 3.62 354.0820.53DRILL, CORE, SKID MTD, 725' MAX DRILL DEPTH (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

69BUSH MASTERD25AD003 $131,374 9.85 1.40 8.91 456.3335.50DRILL, CORE, SKID MTD, 1500' MAX DRILL DEPTH (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

E-Z DRILL, INC.

100210 BD25EZ002 $7,469 0.51 0.08 0.00 30.341.98DRILL, CORE, SKID MTD, 0.6''-2.5'' DIA., 18" DEPTH, HORIZONTAL DOWELLING ASSEMBLY (ADD COST FOR DRILL STEEL AND BIT WEAR, ADD 100 CFM COMPRESSOR)

CFM A

100210 B SRAD25EZ003 $8,127 0.58 0.09 0.00 30.382.11DRILL, CORE, SKID MTD, 0.6''-2.5'' DIA., 18" DEPTH, HORIZONTAL DOWELLING ASSEMBLY (ADD COST FOR DRILL STEEL AND BIT WEAR, ADD 100 CFM COMPRESSOR)

CFM A

100210 B SR HORIZONTAL

D25EZ001 $8,596 0.64 0.09 0.00 30.412.17DRILL, CORE, SKID MTD, 0.6''-2.5'' DIA., 18" DEPTH, HORIZONTAL DOWELLING ASSEMBLY (ADD COST FOR DRILL STEEL AND BIT WEAR, ADD 100 CFM COMPRESSOR)

CFM A

EP 1110-1-8, Vol. 430 Nov 11

2-96


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

D25 E-Z DRILL, INC. (continued)100210-3 SRAD25EZ005 $29,692 2.16 0.32 0.00 121.407.06DRILL, CORE, SELF PROPELLED, 0.6''-2.5''

DIA., 18" DEPTH, DOWELLING MACHINE (ADD COST FOR DRILL STEEL AND BIT WEAR, ADD 100 CFM COMPRESSOR)

CFM A

DRILLS, EARTH / AUGER (Add cost for drill steel and cutting edge wear)D300.00 DRILLS, EARTH / AUGER (Add cost for drill steel and cutting edge wear)SUBCATEGORY

HYDRAULIC POWER SYSTEMS, INC.

210H-15D30HD001 $86,725 6.50 0.93 27.13 1464.1849.42DRILL, AUGER, HYDRAULIC, W/60' 8" X 21" LEADS, 15,000 FT-LBS TORQUE (ADD COST FOR DRILL STEEL AND CUTTING EDGE WEAR AND CRANE)

HP D-off

270H-35VTD30HD002 $130,051 9.75 1.39 34.88 2006.2767.58DRILL, AUGER, HYDRAULIC, W/60' 8" X 27" LEADS, 33,000 FT-LBS TORQUE (ADD COST FOR DRILL STEEL AND CUTTING EDGE WEAR AND CRANE)

HP D-off

335H-50VTD30HD003 $169,294 12.70 1.81 43.28 2698.1685.69DRILL, AUGER, HYDRAULIC, W/60' 8" X 33" LEADS, 50,000 FT-LBS TORQUE (ADD COST FOR DRILL STEEL AND CUTTING EDGE WEAR AND CRANE)

HP D-off

FOREMOST MOBILE DRILLING COMPANY, INC.

8MINUTEMAND30MR001 $14,128 1.06 0.15 2.08 40.685.13DRILL, EARTH / AUGER, W/AUGER KIT, 3" DIA, 30' DEPTH, 350 FT-LBS TORQUE, PORTABLE (ADD COST FOR DRILL STEEL AND CUTTING EDGE WEAR)

HP G

EP 1110-1-8, Vol. 430 Nov 11

2-97


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

D30 FOREMOST MOBILE DRILLING COMPANY, INC. (continued)

58B-31D30MR003 $95,750 7.10 1.02 7.49 424.5727.11DRILL, EARTH / AUGER, HYDRAULIC AUGER, 14" DIA, 30' DEPTH, 3,500 FT-LBS TORQUE, TRAILER MOUNTED (ADD COST FOR DRILL STEEL AND CUTTING EDGE WEAR)

HP D-off

100B-53D30MR005 $230,573 17.06 2.46 17.41 12010.9964.67230 HP D-onDRILL, EARTH / AUGER, MULTI-PURPOSE, 6" DIA, 245' DEPTH, 5,955 FT-LBS TORQUE, W/21,000 GVW TRUCK (W/PTO DRIVE)(ADD COST FOR DRILL STEEL AND CUTTING EDGE WEAR)

HP D-off

115B-58D30MR006 $237,505 17.58 2.53 19.93 13011.3268.86260 HP D-onDRILL, EARTH / AUGER, MULTI-PURPOSE, 8" DIA, 250' DEPTH, 7,000 FT-LBS TORQUE W/33,000 GVW TRUCK (ADD COST FOR DRILL STEEL AND CUTTING EDGE WEAR)

HP D-off

115B-61HTD30MR007 $300,030 22.27 3.20 19.93 20514.3481.07260 HP D-onDRILL, EARTH / AUGER, MULTI-PURPOSE, 8" DIA, 375' DEPTH, 20,000 FT-LBS TORQUE W/33,000 GVW TRUCK (ADD COST FOR DRILL STEEL AND CUTTING EDGE WEAR)

HP D-off

DRILLS, ROTARY BLASTHOLE (Add cost for drill steel and bit wear)D350.11 DIESEL, 4.5" THRU 9.875" DIAMETER HOLE (Add cost for drill steel and bit wear)SUBCATEGORY

DRILTECH, INC. (SANDVIK)

450D25KSD35DT001 $777,555 44.43 7.85 58.14 62030.07181.04DRILL, ROTARY BLASTHOLE, 5''-6.75'' DIA., 27,000 LB PULLDOWN, CRAWLER, 88' DEEP(ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-98


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

D35 DRILTECH, INC. (SANDVIK) (continued)450D245KSD35DT002 $798,356 45.62 8.06 58.14 72030.87184.07DRILL, ROTARY BLASTHOLE, 5''-8'' DIA.,

40,000 LB PULLDOWN, CRAWLER, 148' DEEP (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

450D45KSD35DT003 $898,192 51.33 9.07 58.14 1,05034.74198.61DRILL, ROTARY BLASTHOLE, 6''-9'' DIA., 45,000 LB PULLDOWN, CRAWLER, 208' DEEP (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

525D50KSD35DT004 $952,653 54.44 9.62 67.83 1,05036.84217.84DRILL, ROTARY BLASTHOLE, 6''-9.875'' DIA., 50,000 LB PULLDOWN, CRAWLER, 148' DEEP (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

760D55SPD35DT005 $1,483,770 84.79 14.98 98.19 1,32057.38330.58DRILL, ROTARY BLASTHOLE, 6.75''-10'' DIA., 45,000 LB PULLDOWN, CRAWLER, 55' DEEP (SINGLE PASS) (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

REEDRILL (TEREX)

400SK5ADD35RD001 $506,374 28.94 5.11 58.51 52519.58142.01350 HP D-onDRILL, ROTARY BLASTHOLE, 4"-7" DIA, 12,000 LBS PULL BACK, TRUCK MTD, 148' DEEP (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

0.12 DIESEL, OVER 9.875" DIAMETER (Add cost for drill steel and bit wear)SUBCATEGORY

DRILTECH, INC. (SANDVIK)

760D75KSD35DT006 $1,294,117 57.52 12.90 98.19 1,40041.66261.26DRILL, ROTARY BLASTHOLE, 9''-11'' DIA., 75,000 LB PULLDOWN, CRAWLER, 173' DEEP (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-99


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

INGERSOLL RAND ROTARY DRILL DIV

465T3WD35IB004 $712,536 31.40 7.10 67.49 66022.80159.80380 HP D-onDRILL, ROTARY BLASTHOLE, WATER WELL 6"-24" DIA, 30,000 LB PULL BACK, TRUCK MTD (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

475TH-60D35IB003 $747,503 33.00 7.45 68.78 60023.95165.17380 HP D-onDRILL, ROTARY BLASTHOLE, WATER WELL, 12" DIA, 26,500 LBS PULL BACK, TRUCK MTD (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

575T3W DEEPHOLED35IB005 $825,991 36.45 8.23 81.70 68826.46189.10380 HP D-onDRILL, ROTARY BLASTHOLE, WATER WELL 6"-18" DIA, 50,000 LB PULL BACK, TRUCK MTD (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

600T4WD35IB006 $868,463 38.33 8.66 83.47 68827.83196.02305 HP D-onDRILL, ROTARY BLASTHOLE, WATER WELL 6"-20" DIA, 70,000 LB PULL BACK, TRUCK MTD (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

FORK LIFTSF100.00 FORK LIFTSSUBCATEGORY

JCB INC.

75930-4F10JC001 $74,627 5.72 0.77 7.91 1503.6322.28FORK LIFT, ROUGH TERRAIN, 6,000 LBS @ 28' HIGH STRAIGHT MAST, 4X4

HP D-off

75940-4F10JC002 $81,180 6.25 0.84 7.91 1653.9723.42FORK LIFT, ROUGH TERRAIN, 8,000 LBS @ 30' HIGH STRAIGHT MAST, 4X4

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-100


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

GENERATOR SETSG100.10 PORTABLESUBCATEGORY

WACKER CORPORATION

8GP 3800AG10WC00 $2,439 0.27 0.02 1.70 20.162.38GENERATOR SET, PORTABLE, 3.7 KW, 120/240V, 60 HZ

HP G

11GP 5600AG10WC00 $2,822 0.32 0.03 2.34 20.193.18GENERATOR SET, PORTABLE, 5.6 KW, 120/240V, 60 HZ

HP G

16GS 8.5VG10WC00 $5,206 0.59 0.05 3.41 20.354.85GENERATOR SET, PORTABLE, 8.5 KW, 120/240V, 60 HZ, WITH ELECTRIC START

HP G

18GS 9.7VG10WC00 $4,254 0.48 0.04 3.83 20.285.11GENERATOR SET, PORTABLE, 9.7 KW, 120/240V, 60 HZ, WITH ELECTRIC START

HP G


11000G10XX001 $1,102 0.12 0.01 0.21 10.070.45GENERATOR SET, PORTABLE, 1 KW HP G

9D4500G10XX004 $6,334 0.71 0.06 0.95 30.422.36GENERATOR SET, PORTABLE, 5 KW HP D-off

1910000G10XX002 $5,381 0.61 0.05 4.05 60.365.60GENERATOR SET, PORTABLE, 10 KW

HP G

2310000DG10XX003 $12,250 1.38 0.12 2.42 90.815.22GENERATOR SET, PORTABLE, 10 KW

HP D-off

0.20 SKID MOUNTEDSUBCATEGORY


1743304 PKG - P 304DE03

G10CA020 $30,186 2.72 0.29 18.34 371.6525.68GENERATOR SET, SKID MTD, 113 EKW, 240/480V, 60 HZ PGS PRIME

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-101


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

G10 CATERPILLAR INC. ( MACHINE DIVISION) (continued)

3143306 PKG - 306DE39

G10CA012 $37,387 3.36 0.36 33.10 502.0443.28GENERATOR SET, SKID MTD, 210 EKW, 240 VOLT, 60 HZ PGS PRIME

HP D-off

4053406 PKG - 306DE30


HP D-off

5363406 PKG - 406DE30


HP D-off

6873412 PKG - 412DE3H


HP D-off

8173412 PKG - 412DE30


HP D-off

1,0003508 PKG - 508DE34


HP D-off

2,2063512 PKG - 512DE1F


HP D-off

2,3043516 PKG - 516DE35


HP D-off


3625GG10XX005 $19,346 1.74 0.19 7.67 161.0611.94GENERATOR SET, SKID MTD, 25 KW HP G



10775DG10XX008 $31,415 2.83 0.30 11.28 381.7218.09GENERATOR SET, SKID MTD, 75 KW HP D-off

143100DG10XX009 $26,954 2.43 0.26 15.07 421.4821.48GENERATOR SET, SKID MTD, 100 KW

HP D-off


HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-102


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

G10 NO SPECIFIC MANUFACTURER (continued)375200DG10XX011 $44,100 3.97 0.42 39.53 602.4151.59GENERATOR SET, SKID MTD, 200

KW HP D-off


HP D-off


HP D-off


HP D-off

1,050750DG10XX015 $155,052 13.95 1.49 110.67 2158.47150.08GENERATOR SET, SKID MTD, 750 KW

HP D-off

1,4251000DG10XX016 $219,304 19.74 2.11 150.20 25011.98205.29GENERATOR SET, SKID MTD, 1,000 KW

HP D-off

GRADERS, MOTORG150.00 GRADERS, MOTORSUBCATEGORY


138120-MG15CA001 $291,435 14.93 3.04 13.61 29910.5151.58GRADER, MOTOR, ARTICULATED, 6X4, 12' BLADE W/17 TEETH SCARIFIERS

HP D-off

135135-HG15CA007 $246,483 12.61 2.57 13.31 3098.8845.82GRADER, MOTOR, ARTICULATED, 6X4, 12' BLADE W/17 TEETH SCARIFIERS

HP D-off

15812-MG15CA003 $270,275 13.84 2.82 15.58 3369.7451.30GRADER, MOTOR, ARTICULATED, 6X4, 12' BLADE W/17 TEETH SCARIFIERS

HP D-off

183140-MG15CA004 $298,074 14.81 3.11 18.04 33410.5260.44GRADER, MOTOR, ARTICULATED, 6X4, 12' BLADE W/5 RIPPER/SCARIFIERS

HP D-off

185143-HG15CA008 $337,982 16.87 3.53 18.24 36411.9766.13GRADER, MOTOR, ARTICULATED, 6X6, AWD, 12' BLADE W/5 RIPPER/SCARIFIERS

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-103


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

G15 CATERPILLAR INC. ( MACHINE DIVISION) (continued)

213160-MG15CA009 $329,577 16.44 3.44 21.00 35111.6667.64GRADER, MOTOR, ARTICULATED, 6X4, 14' BLADE W/5 RIPPER/SCARIFIERS

HP D-off

200163-HG15CA010 $365,589 18.30 3.82 19.72 38812.9771.15GRADER, MOTOR, ARTICULATED, 6X6, AWD, 14' BLADE W/5 RIPPER/SCARIFIERS

HP D-off

25914-MG15CA005 $450,163 22.68 4.70 25.54 47116.0487.36GRADER, MOTOR, ARTICULATED, 6X4, 14' BLADE W/7 SHANK RIPPER

HP D-off

29716-MG15CA006 $680,556 34.50 7.11 29.28 57524.36120.80GRADER, MOTOR, ARTICULATED, 6X4, 16' BLADE W/7 SHANK RIPPER

HP D-off

DEERE & COMPANY

151670CHG15JD008 $253,458 12.48 2.65 14.89 3438.8951.62GRADER, MOTOR, ARTICULATED, 6X4, AWD, 12' BLADE W/5 RIPPER/SCARIFIERS

HP D-off

156672CH (HFWD)G15JD009 $291,950 14.47 3.05 15.38 35310.2957.49GRADER, MOTOR, ARTICULATED, 6X6, AWD, 12' BLADE W/5 RIPPER/SCARIFIERS

HP D-off

185770CHG15JD010 $292,982 14.52 3.06 18.24 35310.3260.22GRADER, MOTOR, ARTICULATED, 6X4, AWD, 12' BLADE W/5 RIPPER/SCARIFIERS

HP D-off

205772CH (HFWD)G15JD011 $330,958 16.49 3.46 20.21 36311.7167.75GRADER, MOTOR, ARTICULATED, 6X6, AWD, 12' BLADE W/5 RIPPER/SCARIFIERS

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-104


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

HAMMERS, HYDRAULIC (Demolition tool) (Add cost for point wear)H100.00 HAMMERS, HYDRAULIC (Demolition tool) (Add cost for point wear)SUBCATEGORY

NPK CONSTRUCTION EQUIPMENT

E-200H10NP001 $7,713 1.03 0.08 0.00 20.603.02HAMMERS, HYDRAULIC, 150 FT-LBS, IMPACT FREQUENCY 700 BPM (ADD 150-250 HP HYDRAULIC EXCAVATOR H25)(ADD COST FOR POINT WEAR)

E-201H10NP002 $8,566 1.14 0.09 0.00 20.663.30HAMMERS, HYDRAULIC, 200 FT-LBS, IMPACT FREQUENCY 750 BPM (ADD 60-75 HP HYDRAULIC EXCAVATOR H25 OR L50)(ADD COST FOR POINT WEAR)

E-202H10NP003 $12,823 1.71 0.14 0.00 41.004.95HAMMERS, HYDRAULIC, 350 FT-LBS, IMPACT FREQUENCY 800 BPM (ADD 60-75HP HYDRAULIC EXCAVATOR H25 OR L50)(ADD COST FOR POINT WEAR)



E-205H10NP006 $29,389 3.92 0.32 0.00 112.2810.62HAMMERS, HYDRAULIC, 1,300 FT-LBS, IMPACT FREQUENCY 750 BPM (ADD 95-125 HP HYDRAULIC EXCAVATOR H25)(ADD COST FOR POINT WEAR)

EP 1110-1-8, Vol. 430 Nov 11

2-105


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

H10 NPK CONSTRUCTION EQUIPMENT (continued)



E-210AH10NP015 $69,335 9.24 0.75 0.00 345.3723.93HAMMERS, HYDRAULIC, 3,000 FT-LBS, IMPACT FREQUENCY 670 BPM (ADD 20-28 TON HYDRAULIC EXCAVATOR H25)(ADD COST FOR POINT WEAR)

E-216H10NP016 $95,556 12.74 1.04 0.00 567.4132.52HAMMERS, HYDRAULIC, 5,500 FT-LBS, IMPACT FREQUENCY 500 BPM (ADD 28-43 TON HYDRAULIC EXCAVATOR H25)(ADD COST FOR POINT WEAR)

E-220H10NP017 $124,774 16.64 1.35 0.00 689.6742.07HAMMERS, HYDRAULIC, 8,000 FT-LBS, IMPACT FREQUENCY 430 BPM (ADD 33-50 TON HYDRAULIC EXCAVATOR H25)(ADD COST FOR POINT WEAR)

E-260AH10NP018 $289,630 38.62 3.14 0.00 17022.4596.01HAMMERS, HYDRAULIC, 20,000 FT-LBS, IMPACT FREQUENCY 330 BPM (ADD 80-130 TON HYDRAULIC EXCAVATOR H25)(ADD COST FOR POINT WEAR)

EP 1110-1-8, Vol. 430 Nov 11

2-106


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

HAZARDOUS/TOXIC WASTE EQUIPMENTH130.11 COMPACTORS (Compression force) 0 THRU 50 TONSSUBCATEGORY

CONSOLIDATED BALING MACHINE COMPANY, INC

5DOS RAW WIH13CB001 $25,262 2.15 0.25 0.26 251.335.27HAZARDOUS/TOXIC WASTE EQIPMENT, COMPACTOR, RADIOLOGICAL WASTE, 12.5 TON, LOW LEVEL

HP E

10DOS RAW W2H13CB002 $27,314 2.32 0.27 0.53 251.436.06HAZARDOUS/TOXIC WASTE EQUIPMENT, COMPACTOR, RADIOLOGICAL WASTE, 20 TON, LOW LEVEL

HP E

WASTE CONTROL SYSTEMS, INC.

58041CCH13CO002 $11,797 1.00 0.12 0.26 1670.622.81HAZARDOUS/TOXIC WASTE EQUIPMENT, COMPACTOR, 37 TON HAZARD WASTE IN-DRUM , EXPLOSION PROOF

HP E

ENVIRO-PAK

54000HMH13EP001 $29,811 2.53 0.30 0.26 321.576.10HAZARDOUS/TOXIC WASTE EQUIPMENT, COMPACTOR, 30 TON HAZARDOUS WASTE, HAZ-MAT STORAGE CONTAINER 40"X40"X40"

HP E

TEEMARK CORPORATION

5DPC60-E50H13TH001 $13,994 1.19 0.14 0.26 200.742.96HAZARDOUS/TOXIC WASTE EQUIPMENT, COMPACTOR, 30 TON DRUM CRUSHER

HP E

9DPC60-D90H13TH002 $26,339 2.20 0.26 0.95 321.365.86HAZARDOUS/TOXIC WASTE EQUIPMENT, COMPACTOR, 30 TON DRUM CRUSHER, TRAILER MOUNTED

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-107


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

H13 TEEMARK CORPORATION (continued)9DPC85-D90H13TH003 $29,785 2.49 0.30 0.95 471.556.49HAZARDOUS/TOXIC WASTE EQUIPMENT,

COMPACTOR, 42.5 TON DRUM CRUSHER, TRAILER MOUNTED

HP D-off

ADVANCED ENVIRONMENTAL SOLUTIONS

50CCYCH13YB001 $387,622 32.95 3.87 2.63 32020.3574.97HAZARDOUS/TOXIC WASTE EQUIPMENT, COMPACTOR, 700 PSI OPERATING PRESSURE, FINAL COMPACTED SIZE 39.4" X 39.4" X 39.4"

HP E

50CCYC-HD-EH13YB002 $387,622 32.95 3.87 2.63 32020.3574.97HAZARDOUS/TOXIC WASTE EQUIPMENT, COMPACTOR, 1,000 PSI OPERATING PRESSURE, FINAL COMPACTED SIZE 39.4" X 39.4" X 39.4"

HP E

50CMC-HDH13YB003 $387,622 32.95 3.87 2.63 32020.3574.97HAZARDOUS/TOXIC WASTE EQUIPMENT, COMPACTOR, 1,200 PSI OPERATING PRESSURE, FINAL COMPACTED SIZE 39.4" X 39.4" X 39.4"

HP E

0.12 COMPACTORS (Compression force) OVER 50 TONSSUBCATEGORY

WASTE CONTROL SYSTEMS, INC.

38551H13CO003 $25,144 1.68 0.26 0.16 2701.104.51HAZARDOUS/TOXIC WASTE EQUIPMENT, COMPACTOR, 85 TON HAZARD WASTE IN-DRUM

HP E

38564H13CO004 $37,066 2.47 0.38 0.16 2901.626.65HAZARDOUS/TOXIC WASTE EQIPMENT, COMPACTOR, 85 TON HAZARD WASTE IN-DRUM, W/HEPA FILTER

HP E

38560-EXH13CO006 $54,086 3.61 0.55 0.16 3002.369.21HAZARDOUS/TOXIC WASTE EQUIPMENT, COMPACTOR, 85 TON HAZARD WASTE IN-DRUM, W/HEPA FILTER & SS PLATEN & CHAMBER

HP E

EP 1110-1-8, Vol. 430 Nov 11

2-108


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

H13 WASTE CONTROL SYSTEMS, INC. (continued)

38560-EXLH13CO005 $64,452 4.30 0.66 0.16 3102.8111.02HAZARDOUS/TOXIC WASTE EQUIPMENT, COMPACTOR, 85 TON HAZARD WASTE IN-DRUM, EXPLOSION PROOF, W/LIQUID REMOVAL SYSTEM

HP E

ENVIRO-PAK

89600HMH13EP002 $39,016 2.60 0.40 0.39 1001.707.12HAZARDOUS/TOXIC WASTE EQUIPMENT, COMPACTOR, 42.5 TON HAZARDOUS WASTE, B-25 METAL STORAGE CONTAINER 4'X4'X6'

HP E

0.21 FILTER PRESSES, STATIONARYSUBCATEGORY

KOMLINE-SANDERSON ENGINEERING CO.

100L/S 1200/25H13AY015 $66,214 5.30 0.68 0.00 1123.3312.52HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, STATIONARY, 25 CF MEMBRANE, 1,200 MM SQ (ADD 100 CFM COMPRESSOR)

CFM A

100K/F 1200/25H13AY016 $42,897 3.43 0.44 0.00 1082.168.11HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, STATIONARY, 25 CF CONVENTIONAL, 1,200 MM SQ (ADD 100 CFM COMPRESSOR)

CFM A


CFM A


CFM A

EP 1110-1-8, Vol. 430 Nov 11

2-109


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

H13 KOMLINE-SANDERSON ENGINEERING CO. (continued)


CFM A


CFM A


CFM A


CFM A


CFM A


CFM A


CFM A

EP 1110-1-8, Vol. 430 Nov 11

2-110


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT



CFM A

1H13AY019 $13,694 1.10 0.14 0.05 50.692.92HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, STATIONARY, FILTER PRESS PLATE SHIFTING UNIT, 1,200 MM SQ, MECHANIZED

HP E

1SLC-500H13AY020 $17,745 1.42 0.18 0.05 20.893.68HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, STATIONARY, PLC CONTROL PANEL - PLATE SHIFTING, COMPUTER AUTOMATED

HP E

USFILTER PERRIN PRODUCTS

3PLC 25-1000H13PR001 $105,197 8.42 1.09 0.16 1255.3020.15HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, STATIONARY, 25 CF STANDARD FILTER PRESS, 1,000 MM SQ

HP E


HP E


HP E

10PLC 270-1500H13PR007 $297,611 23.81 3.07 0.53 1,10014.9857.10HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, STATIONARY, 270 CF MAXI FILTER PRESS, 1,500 MM SQ

HP E

EP 1110-1-8, Vol. 430 Nov 11

2-111


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

H13 USFILTER PERRIN PRODUCTS (continued)2BPR 1200-15HH13PR022 $217,592 17.41 2.24 0.11 19110.9541.32HAZARDOUS/TOXIC WASTE EQUIPMENT,

FILTER PRESS, STATIONARY, 47" WIDE FILTER BELT PRESS, 2 HP

HP E

3BPR 1600-15HH13PR023 $248,889 19.91 2.57 0.16 25812.5347.32HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, STATIONARY, 63" WIDE FILTER BELT PRESS, 3 HP

HP E

3BPR 2000-15HH13PR024 $275,954 22.08 2.85 0.16 31913.8952.44HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, STATIONARY, 78.75" WIDE FILTER BELT PRESS, 3 HP

HP E

3BPR 2500-15HH13PR025 $333,170 26.65 3.44 0.16 51516.7763.26HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, STATIONARY, 98.5" WIDE FILTER BELT PRESS, 3 HP

HP E

4BPR 3000-15HH13PR026 $406,110 32.49 4.19 0.21 59420.4477.13HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, STATIONARY, 118" WIDE FILTER BELT PRESS, 4 HP

HP E

0.22 FILTER PRESSES, MOBILESUBCATEGORY

KOMLINE-SANDERSON ENGINEERING CO.

100L/S 1200/25MH13AY031 $82,428 6.80 0.82 0.00 1124.2215.30HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, MOBILE, 25 CF MEMBRANE, 1,200 MM SQ, TRAILER MOUNTED (ADD 100 CFM COMPRESSOR)

CFM A

100K/F 1200/25MH13AY032 $55,025 4.48 0.55 0.00 1092.7910.30HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, MOBILE, 25 CF CONVENTIONAL, 1,200 MM SQ, TRAILER MOUNTED (ADD 100 CFM COMPRESSOR)

CFM A

EP 1110-1-8, Vol. 430 Nov 11

2-112


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT



CFM A


CFM A


CFM A


CFM A


CFM A


CFM A

EP 1110-1-8, Vol. 430 Nov 11

2-113


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)



CFM A


CFM A


CFM A

100K/F 1200/150MH13AY022 $122,576 10.22 1.22 0.00 2446.3322.65HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, MOBILE, 150 CF CONVENTIONAL, 1200 MM SQ, TRAILER MOUNTED (ADD 100 CFM COMPRESSOR)

CFM A

KOCH-WATER

13BFP-0500H13KP001 $86,579 7.31 0.86 0.66 404.5216.91HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, MOBILE, FILTER BELT PRESS, 20" (0.5M) WIDE, 0.6 - 2.0 TONS/HR, TRAILER MOUNTED (STAND ALONE UNIT, INCLUDES POLYMER FEED PUMP, BOOSTER PUMP, SLUDGE PUMP, AND DISCHARGE CONVEYOR)

HP E

EP 1110-1-8, Vol. 430 Nov 11

2-114


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

H13 KOCH-WATER (continued)16BFP-1000H13KP002 $98,169 8.30 0.98 0.82 485.1319.29HAZARDOUS/TOXIC WASTE EQUIPMENT,

FILTER PRESS, MOBILE, FILTER BELT PRESS, 39" (1.0M) WIDE, 3.0 - 6.5 TONS/HR, TRAILER MOUNTED (STAND ALONE UNIT, INCLUDES POLYMER FEED PUMP, BOOSTER PUMP, SLUDGE PUMP, AND DISCHARGE CONVEYOR)

HP E


HP E


HP E

USFILTER PERRIN PRODUCTS

3PLC 25-1000MH13PR002 $296,017 24.96 2.96 0.16 14515.4456.12HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, MOBILE, 25 CF STANDARD FILTER PRESS, 1,000 MM SQ, TRAILER MOUNTED (COMPLETE)

HP E

5180-1500MH13PR006 $261,535 22.03 2.61 0.26 70513.6349.96HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, MOBILE, 180 CF STANDARD FILTER PRESS,1,500 MM SQ, TRAILER MOUNTED

HP E

EP 1110-1-8, Vol. 430 Nov 11

2-115


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

H13 USFILTER PERRIN PRODUCTS (continued)2BPR 1200-15H-

MH13PR011 $408,829 34.55 4.08 0.11 23521.3676.67HAZARDOUS/TOXIC WASTE EQUIPMENT,

FILTER PRESS, MOBILE, 47" FILTER BELT PRESS, TRAILER MOUNTED (STAND ALONE UNIT, ADD APPURTENANCES SUCH AS FEED PUMPS, POLYMER SYSTEM, WASH WATER BOOSTER PUMP, CONVEYOR ETC.)

HP E

3BPR 1600-15H-M

H13PR012 $439,520 37.16 4.39 0.16 30222.9782.37HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, MOBILE, 63" FILTER BELT PRESS, TRAILER MOUNTED (STAND ALONE UNIT, ADD APPURTENANCES SUCH AS FEED PUMPS, POLYMER SYSTEM, WASH WATER BOOSTER PUMP, CONVEYOR ETC.)

HP E

5BPR 2000-15H-M

H13PR013 $466,428 39.44 4.66 0.26 31924.3887.43HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, MOBILE, 78.75" FILTER BELT PRESS, TRAILER MOUNTED (STAND ALONE UNIT, ADD APPURTENANCES SUCH AS FEED PUMPS, POLYMER SYSTEM, WASH WATER BOOSTER PUMP, CONVEYOR ETC.)

HP E

8BPR 2500-15H-M

H13PR014 $523,644 44.31 5.23 0.42 51527.3998.15HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, MOBILE, 98.5" FILTER BELT PRESS, TRAILER MOUNTED (STAND ALONE UNIT, ADD APPURTENANCES SUCH AS FEED PUMPS, POLYMER SYSTEM, WASH WATER BOOSTER PUMP, CONVEYOR ETC.)

HP E

EP 1110-1-8, Vol. 430 Nov 11

2-116


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

H13 USFILTER PERRIN PRODUCTS (continued)8BPR 3000-15H-

MH13PR015 $596,584 50.51 5.96 0.42 59431.22111.49HAZARDOUS/TOXIC WASTE EQUIPMENT,

FILTER PRESS, MOBILE, 118" FILTER BELT PRESS, TRAILER MOUNTED (STAND ALONE UNIT, ADD APPURTENANCES SUCH AS FEED PUMPS, POLYMER SYSTEM, WASH WATER BOOSTER PUMP, CONVEYOR ETC.)

HP E

SOMAT WASTE REDUCTION TECHNOLOGY

31PB-6DH13S5001 $58,946 5.01 0.59 0.16 143.1011.03HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, MOBILE, PUSHER SCREW PRESS, 6-15 GPM CAPACITY, TRAILER MOUNTED

HP E


HP E


HP E

0.30 CENTRIFUGESSUBCATEGORY

NORTH STAR ENGINEERED PRODUCTS, INC.

3GP 35H13BC013 $16,067 3.21 0.19 0.16 91.806.74HAZARDOUS/TOXIC WASTE EQUIPMENT, CENTRIFUGE, FIXED SPEED, TIMER, 35 LB DRY WT.

HP E

3305 TXH13BC010 $13,982 2.80 0.16 0.16 61.565.90HAZARDOUS/TOXIC WASTE EQUIPMENT, CENTRIFUGE, FIXED SPEED, TIMER, 35 LB DRY WT.

HP E

EP 1110-1-8, Vol. 430 Nov 11

2-117


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

H13 NORTH STAR ENGINEERED PRODUCTS, INC. (continued)


HP E

3605 TXH13BC006 $17,254 3.45 0.20 0.16 91.937.22HAZARDOUS/TOXIC WASTE EQUIPMENT, CENTRIFUGE, FIXED SPEED, TIMER, 60 LB DRY WT.

HP E


HP E


HP E

3355H13BC009 $24,564 4.91 0.28 0.16 62.7410.16HAZARDOUS/TOXIC WASTE EQUIPMENT, CENTRIFUGE, FIXED SPEED, MANUAL CONTROL, EXPLOSION PROOF, 35 LB

HP E


HP E


HP E

EP 1110-1-8, Vol. 430 Nov 11

2-118


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

0.40 SHREDDERSSUBCATEGORY

GRANUTE-SATURN SYSTEMS(MAC CORPORATION)

15052-32HTH13MN001 $369,327 31.06 3.69 7.90 20019.2286.34HAZARDOUS/TOXIC WASTE EQUIPMENT, SHREDDER, 32" X 52" OPENING, TRAILER MTD, W/DIESEL GENERATOR SET/ BELT-TYPE INFEED & DISCHARGE CONVEYORS

HP E

20062-40HTH13MN002 $432,305 36.26 4.32 10.53 30022.45103.45HAZARDOUS/TOXIC WASTE EQUIPMENT, SHREDDER, 38" X 62" OPENING, TRAILER MTD, W/DIESEL GENERATOR SET, HOOK-TYPE INFEED FOR TIRES, & DISCHARGE CONVEYOR

HP E

20062-40HTH13MN003 $489,868 41.15 4.89 10.53 30025.47115.60HAZARDOUS/TOXIC WASTE EQUIPMENT, SHREDDER, 38" X 62" OPENING, TRAILER MTD, W/DIESEL GENERATOR SET, CRANE GRAPPLE & DISCHARGE CONVEYOR SYSTEM

HP E

30072-46HTH13MN004 $559,024 47.03 5.58 15.80 40029.10137.89HAZARDOUS/TOXIC WASTE EQUIPMENT, SHREDDER, 45" X 72" OPENING , TRAILER MTD, W/DIESEL GENERATOR SET, CRANE GRAPPLE & DISCHARGE CONVEYOR SYSTEM

HP E

SHRED-TECH LIMITED

20ST-25EH13SH001 $57,077 4.85 0.57 1.05 203.0012.63HAZARDOUS/TOXIC WASTE EQUIPMENT, SHREDDER, 29" X 42" OPENING, TRAILER MTD. (ADD COST FOR CONVEYOR SYSTEM, POWER SUPPLY, AND TRAILER)

HP E

EP 1110-1-8, Vol. 430 Nov 11

2-119


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

H13 SHRED-TECH LIMITED (continued)20ST-25ELH13SH002 $53,536 4.55 0.53 1.05 232.8111.94HAZARDOUS/TOXIC WASTE EQUIPMENT,

SHREDDER, 29" X 46" OPENING, TRAILER MTD. (ADD COST FOR CONVEYOR SYSTEM, POWER SUPPLY, AND TRAILER)

HP E

40ST-50H13SH003 $92,152 7.83 0.92 2.11 454.8421.01HAZARDOUS/TOXIC WASTE EQUIPMENT, SHREDDER, 40" X 55" OPENING, TRAILER MTD. (ADD COST FOR CONVEYOR SYSTEM, POWER SUPPLY, AND TRAILER)

HP E

40ST-50LH13SH004 $96,165 8.17 0.96 2.11 505.0521.79HAZARDOUS/TOXIC WASTE EQUIPMENT, SHREDDER, 40" X 65" OPENING, TRAILER MTD. (ADD COST FOR CONVEYOR SYSTEM, POWER SUPPLY, AND TRAILER)

HP E


HP E


HP E

600ST-500LH13SH007 $644,512 54.78 6.43 31.59 44033.82172.15HAZARDOUS/TOXIC WASTE EQUIPMENT, SHREDDER, 66" X 115" OPENING, TRAILER MTD. (ADD COST FOR CONVEYOR SYSTEM, POWER SUPPLY, AND TRAILER)

HP E

EP 1110-1-8, Vol. 430 Nov 11

2-120


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

0.71 WASTE HANDLING EQUIPMENT, DRUM HANDLINGSUBCATEGORY

BASCO

10VELT 55/35H13BB001 $15,158 3.22 0.17 0.53 111.789.09HAZARDOUS/TOXIC WASTE EQUIPMENT, WASTE HANDLING EQUIPMENT, DRUM HANDLING, DRUM FILLER, 55 GAL TOP FILL

HP E

152BH13BB002 $19,388 4.12 0.22 0.79 192.2811.84HAZARDOUS/TOXIC WASTE EQUIPMENT, WASTE HANDLING EQUIPMENT, DRUM CLEANER, 12 DRUM/HR CAP INTERIOR

HP E

HOISTS & AIR WINCHESH200.00 HOISTS & AIR WINCHESSUBCATEGORY

INGERSOLL RAND MATERIAL HANDLING

700FA2.5H20BE002 $40,718 3.62 0.42 0.00 102.238.22AIR WINCH, MANUAL BRAKE, 24" DRUM, 5,000 LBS CAP, 145 FPM (ADD 700 CFM COMPRESSOR)

CFM A

700FA5H20BE003 $50,450 4.48 0.53 0.00 192.7710.24AIR WINCH, MANUAL BRAKE, 24" DRUM, 10,000 LBS CAP, 65 FPM (ADD 700 CFM COMPRESSOR)

CFM A

800FA10H20BE004 $55,341 4.92 0.58 0.00 353.0411.30AIR WINCH, AUTOMATIC BRAKE, 24" DRUM, 22,000 LBS CAP, 30 FPM (ADD 800 CFM COMPRESSOR)

CFM A

EP 1110-1-8, Vol. 430 Nov 11

2-121


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

HYDRAULIC EXCAVATORS, CRAWLER MOUNTEDH250.10 0 LBS THRU 12,500 LBS (COMPACT EXCAVATORS)SUBCATEGORY


18301.8H25CA034 $38,118 3.57 0.41 1.90 372.209.79HYDRAULIC EXCAVATOR, CRAWLER-RUBBER TRACK, 3,800 LBS, 0.04 CY BUCKET, 7.50' MAX DIGGING DEPTH

HP D-off

30303 CRH25CA035 $44,578 4.18 0.48 3.16 762.5712.54HYDRAULIC EXCAVATOR, CRAWLER-RUBBER TRACK, 7,500 LBS, 0.11 CY BUCKET, 9.08' MAX DIGGING DEPTH

HP D-off

47305 CRH25CA036 $71,648 6.72 0.78 4.95 1154.1420.03HYDRAULIC EXCAVATOR, CRAWLER-RUBBER TRACK, 10,800 LBS, 0.17 CY BUCKET, 11.08' MAX DIGGING DEPTH

HP D-off

Komatsu America International Company

20PC20MR-2H25KM018 $48,569 4.55 0.53 2.11 512.8112.13HYDRAULIC EXCAVATOR, CRAWLER-RUBBER TRACK, 4,800 LBS, 0.05 CY BUCKET, 8'11" MAX DIGGING DEPTH

HP D-off

39PC40MR-2H25KM021 $65,362 6.13 0.71 4.11 1063.7817.80HYDRAULIC EXCAVATOR, CRAWLER-RUBBER TRACK, 10,000 LBS, 0.18 CY BUCKET, 12'9" MAX DIGGING DEPTH

HP D-off

40PC58UU-3H25KM022 $83,538 7.83 0.91 4.22 1154.8321.55HYDRAULIC EXCAVATOR, CRAWLER-RUBBER TRACK, 11,400 LBS, 0.29 CY BUCKET, 13'1" MAX DIGGING DEPTH

HP D-off

54PC78US-6H25KM023 $102,986 9.65 1.12 5.69 1595.9527.12HYDRAULIC EXCAVATOR, CRAWLER, 6,200 LBS, 0.37 CY BUCKET, 12'4" MAX DIGGING DEPTH

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-122


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

MELROE COMPANY/BOBCAT

13323H25ME001 $29,725 2.79 0.32 1.40 371.727.55HYDRAULIC EXCAVATOR, CRAWLER-RUBBER TRACK, 3,600 LBS, 0.04 CY BUCKET, 7'6" MAX DIGGING DEPTH

HP D-off

40331H25ME002 $42,623 4.00 0.46 4.22 722.4613.38HYDRAULIC EXCAVATOR, CRAWLER-RUBBER TRACK, 7,200 LBS, 0.10 CY BUCKET, 10'2" MAX DIGGING DEPTH

HP D-off

48337H25ME003 $59,234 5.55 0.64 5.06 1103.4217.66HYDRAULIC EXCAVATOR, CRAWLER-RUBBER TRACK, 11,000 LBS, 0.18 CY BUCKET, 12' MAX DIGGING DEPTH

HP D-off

0.11 OVER 12,500 LBS THRU 40,000 LBSSUBCATEGORY


54307DH25CA038 $103,129 9.10 1.11 5.69 1595.6626.00HYDRAULIC EXCAVATOR, CRAWLER, 14,310 LBS, 0.48 CY BUCKET, 15.25' MAX DIGGING DEPTH

HP D-off

79311-CUH25CA020 $132,023 11.65 1.43 8.33 2587.2634.50HYDRAULIC EXCAVATOR, CRAWLER, 24,640 LBS, 0.60 CY BUCKET, 16.50' MAX DIGGING DEPTH

HP D-off

84312-D LH25CA021 $132,792 11.72 1.44 8.85 2887.3035.25HYDRAULIC EXCAVATOR, CRAWLER, 26,900 LBS, 0.68 CY BUCKET, 18.16' MAX DIGGING DEPTH

HP D-off


5470SRH25KC017 $112,992 9.97 1.22 5.69 1686.2127.86HYDRAULIC EXCAVATOR, CRAWLER, 16,400 LBS, 0.33 CY BUCKET, 14.75' MAX DIGGING DEPTH

HP D-off

94135SR LCH25KC016 $160,424 14.16 1.73 9.91 3198.8141.68HYDRAULIC EXCAVATOR, CRAWLER, 30,870 LBS, 0.60 CY BUCKET, 19.58' MAX DIGGING DEPTH

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-123


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)


86PC128UU-2H25KM027 $200,083 17.65 2.16 9.06 29510.9948.16HYDRAULIC EXCAVATOR, CRAWLER, 12,200 LBS, 0.58 CY BUCKET, 16' 0" MAX DIGGING DEPTH

HP D-off

89PC 120-6H25KM001 $141,550 12.49 1.53 9.38 2657.7837.51HYDRAULIC EXCAVATOR, CRAWLER, 26,950 LBS, 0.75 CY BUCKET, 18.08' MAX DIGGING DEPTH

HP D-off

110PC 160LC-7H25KM003 $194,687 17.18 2.10 11.59 39510.6950.08HYDRAULIC EXCAVATOR, CRAWLER, 39,400 LBS, 1.12 CY BUCKET, 19.58' MAX DIGGING DEPTH

HP D-off


95130 2XLCH25LB003 $159,447 14.07 1.72 10.01 2718.7641.61HYDRAULIC EXCAVATOR, CRAWLER, 27,100 LBS, 0.50 CY BUCKET, 18' 2" MAX DIGGING DEPTH

HP D-off

120160 X2H25LB005 $186,682 16.47 2.02 12.65 36210.2649.79HYDRAULIC EXCAVATOR, CRAWLER, 35,275 LBS, 0.66 CY BUCKET, 20' 1" MAX DIGGING DEPTH

HP D-off



125319CLH25CA040 $143,052 8.94 1.51 13.18 4055.9836.03HYDRAULIC EXCAVATOR, CRAWLER, 40,600 LBS, 1.00 CY BUCKET, 22.50' MAX DIGGING DEPTH

HP D-off

128320DH25CA022 $213,991 13.37 2.26 13.49 4448.9546.71HYDRAULIC EXCAVATOR, CRAWLER, 43,800 LBS, 1.50 CY BUCKET, 21.75' MAX DIGGING DEPTH

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-124


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

H25 CATERPILLAR INC. ( MACHINE DIVISION) (continued)

128320DLH25CA023 $309,398 19.34 3.26 13.49 53612.9360.59HYDRAULIC EXCAVATOR, CRAWLER, 49,000 LBS, 0.80 CY BUCKET, 39.0' MAX DIGGING DEPTH, LONG REACH BOOM

HP D-off


143SK210 LCH25KC019 $249,977 15.62 2.63 15.07 48010.4453.76HYDRAULIC EXCAVATOR, CRAWLER, 48,000 LBS, 1.13 CY BUCKET, 22.00' MAX DIGGING DEPTH

HP D-off

143SK210 LCH25KC020 $274,493 17.16 2.89 15.07 53411.4757.34HYDRAULIC EXCAVATOR, CRAWLER, 53,400 LBS, 0.63 CY BUCKET, 39' MAX DIGGING DEPTH, LONG REACH BOOM

HP D-off


HP D-off

176SK250 LCH25KC022 $328,865 20.55 3.47 18.55 59113.7569.26HYDRAULIC EXCAVATOR, CRAWLER, 59,100 LBS, 0.50 CY BUCKET, 23' MAX DIGGING DEPTH, LONG REACH BOOM

HP D-off


HP D-off



306SK400 LCH25KC024 $516,524 24.21 5.37 32.25 1,01917.4898.47HYDRAULIC EXCAVATOR, CRAWLER, 101,900 LBS 3.06 CY BUCKET, 25.58' MAX DIGGING DEPTH

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-125


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

H25 KOBELCO AMERICA INC. (continued)315SK480LCH25KC026 $541,123 25.37 5.63 33.20 1,08018.32102.55HYDRAULIC EXCAVATOR, CRAWLER,

108,000 LBS, 2.25 CY BUCKET, 25.58' MAX DIGGING DEPTH

HP D-off


384PC 600 LC-8H25KM015 $651,205 30.53 6.77 40.47 1,33222.04123.95HYDRAULIC EXCAVATOR, CRAWLER, 133,160 LBS, 4.25 CY BUCKET, 27.83' MAX DIGGING DEPTH

HP D-off

0.14 OVER 160,000 LBSSUBCATEGORY


454PC 800 LC-8H25KM009 $955,005 37.70 9.85 47.85 1,75028.70157.95HYDRAULIC EXCAVATOR, CRAWLER, 171,070 LBS, 4.05 CY BUCKET, 27.66' MAX DIGGING DEPTH

HP D-off

908PC1800-6H25KM033 $2,228,764 87.98 23.00 95.70 3,96866.99351.82HYDRAULIC EXCAVATOR, CRAWLER, 396,800 LBS, 15.70 CY BUCKET, 30'5" MAX DIGGING DEPTH

HP D-off

0.21 ATTACHMENTS, MOBILE SHEARSSUBCATEGORY


S305H25CA055 $20,611 2.92 0.22 0.00 151.686.93HYDRAULIC EXCAVATOR, ATTACHMENT, MOBILE SHEARS, SCRAP, 9.4" JAW OPENING (ADD 10,000 LB HYDRAULIC EXCAVATOR)

S320BH25CA057 $86,380 12.24 0.91 0.00 577.0328.17HYDRAULIC EXCAVATOR, ATTACHMENT, MOBILE SHEARS, SCRAP, 15.4" JAW OPENING (ADD 20,000 LB HYDRAULIC EXCAVATOR)

EP 1110-1-8, Vol. 430 Nov 11

2-126


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT


S230H25CA052 $108,026 15.30 1.14 0.00 848.7935.73HYDRAULIC EXCAVATOR, ATTACHMENT, MOBILE SHEARS, SCRAP, 22.0" JAW OPENING (ADD 35,000 LB HYDARULIC EXCAVATOR)




LABOUNTY MANUFACTURING,

MSD 7H25LU001 $27,502 3.90 0.29 0.00 102.249.12HYDRAULIC EXCAVATOR, ATTACHMENT, MOBILE SHEARS, 10" JAW OPENING (ADD 10,000 LB HYDRAULIC EXCAVATOR)

MSD 7RH25LU002 $30,997 4.39 0.33 0.00 112.5310.32HYDRAULIC EXCAVATOR, ATTACHMENT, MOBILE SHEARS, 10" JAW OPENING (ADD 14,000 LB HYDRAULIC EXCAVATOR)

MSD 15H25LU003 $47,844 6.78 0.50 0.00 303.8915.96HYDRAULIC EXCAVATOR, ATTACHMENT, MOBILE SHEARS, 18" JAW OPENING (ADD 20,000 LB HYDRAULIC EXCAVATOR)

MSD 15RH25LU004 $55,621 7.88 0.59 0.00 354.5318.53HYDRAULIC EXCAVATOR, ATTACHMENT, MOBILE SHEARS, 18" JAW OPENING (ADD 25,000 LB HYDRAULIC EXCAVATOR)

EP 1110-1-8, Vol. 430 Nov 11

2-127


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

H25 LABOUNTY MANUFACTURING, (continued)MSD 30 - III SVH25LU005 $69,723 9.88 0.73 0.00 505.6723.19HYDRAULIC EXCAVATOR, ATTACHMENT,

MOBILE SHEARS, 22" JAW OPENING (ADD 25,000 LB HYDRAULIC EXCAVATOR)

MSD 30R - III SVH25LU006 $97,702 13.84 1.03 0.00 677.9532.46HYDRAULIC EXCAVATOR, ATTACHMENT, MOBILE SHEARS, 22" JAW OPENING (ADD 35,000 LB HYDRAULIC EXCAVATOR)

MSD 40-III SVH25LU007 $83,320 11.80 0.88 0.00 706.7827.80HYDRAULIC EXCAVATOR, ATTACHMENT, MOBILE SHEARS, 27" JAW OPENING (ADD 40,000 LB HYDRAULIC EXCAVATOR)

MSD 40R-III SVH25LU008 $108,985 15.44 1.15 0.00 908.8736.14HYDRAULIC EXCAVATOR, ATTACHMENT, MOBILE SHEARS, 27" JAW OPENING (ADD 45,000 LB HYDRAULIC EXCAVATOR)







EP 1110-1-8, Vol. 430 Nov 11

2-128


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

0.22 ATTACHMENTS, MATERIAL HANDLINGSUBCATEGORY

BALDERSON, INC.

B315-24H25BS001 $6,945 0.93 0.08 0.00 100.552.03HYDRAULIC EXCAVATOR, ATTACHMENT, MATERIAL HANDLING, 0.50 CY BUCKET, W/TIPS (ADD 25,000-50,000 LB HYDRAULIC EXCAVATOR)

B3F-B-30H25BS002 $7,049 0.94 0.08 0.00 160.552.05HYDRAULIC EXCAVATOR, ATTACHMENT, MATERIAL HANDLING, 0.75 CY BUCKET, W/TIPS (ADD 25,000-50,000 LB HYDRAULIC EXCAVATOR)

B315-48H25BS003 $9,240 1.23 0.10 0.00 300.722.68HYDRAULIC EXCAVATOR, ATTACHMENT, MATERIAL HANDLING, 1.25 CY BUCKET, W/TIPS (ADD 25,000-60,000 LB HYDRAULIC EXCAVATOR)

B3F-C-42H25BS004 $12,256 1.63 0.13 0.00 220.953.56HYDRAULIC EXCAVATOR, ATTACHMENT, MATERIAL HANDLING, 1.50 CY BUCKET, W/TIPS (ADD 50,000-60,000 LB HYDRAULIC EXCAVATOR)

B3F-D-66H25BS005 $16,580 2.21 0.18 0.00 521.294.82HYDRAULIC EXCAVATOR, ATTACHMENT, MATERIAL HANDLING, 3.25 CY BUCKET, W/TIPS (ADD 50,000-75,000 LB HYDRAULIC EXCAVATOR)


TW 100H25LU023 $37,892 5.05 0.41 0.00 162.9411.26HYDRAULIC EXCAVATOR, ATTACHMENT, MATERIAL HANDLING, GRAPPLE, 1.25CY, 4-TINE/ 5-TINE (ADD 25,000 LB HYDRAULIC EXCAVATOR)

EP 1110-1-8, Vol. 430 Nov 11

2-129


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

H25 LABOUNTY MANUFACTURING, (continued)TW 110H25LU024 $18,882 2.52 0.21 0.00 281.475.80HYDRAULIC EXCAVATOR, ATTACHMENT,

MATERIAL HANDLING, GRAPPLE, 3.50CY, 4-TINE/ 5-TINE (ADD 35,000 LB HYDRAULIC EXCAVATOR)

120 TRH25LU025 $23,144 3.09 0.25 0.00 351.807.13HYDRAULIC EXCAVATOR, ATTACHMENT, MATERIAL HANDLING, GRAPPLE, 3.50CY, 4-TINE/ 5-TINE (ADD 45,000 LB HYDRAULIC EXCAVATOR)

140 TWH25LU026 $26,327 3.51 0.29 0.00 482.058.16HYDRAULIC EXCAVATOR, ATTACHMENT, MATERIAL HANDLING, GRAPPLE, 5.50CY, 4-TINE/ 5-TINE (ADD 60,000 LB HYDRAULIC EXCAVATOR)

160 TRH25LU027 $29,458 3.93 0.32 0.00 582.299.17HYDRAULIC EXCAVATOR, ATTACHMENT, MATERIAL HANDLING, GRAPPLE, 6.50CY, 4-TINE/ 5-TINE (ADD 75,000 LB HYDRAULIC EXCAVATOR)

TW 170H25LU028 $48,664 6.49 0.53 0.00 783.7814.85HYDRAULIC EXCAVATOR, ATTACHMENT, MATERIAL HANDLING, GRAPPLE, 9.00CY, 4-TINE/ 5-TINE (ADD 100,000 LB HYDRAULIC EXCAVATOR)

RDG 60H25LU034 $71,036 9.47 0.77 0.00 355.5121.45HYDRAULIC EXCAVATOR, ATTACHMENT, MATERIAL HANDLING, ROTATING GRAPPLE, 1.75 CY (ADD 38,000-70,000 LB HYDRAULIC EXCAVATOR)

RDG 90H25LU035 $85,045 11.34 0.92 0.00 696.5925.62HYDRAULIC EXCAVATOR, ATTACHMENT, MATERIAL HANDLING, ROTATING GRAPPLE, 1.25 CY (ADD 70,000-140,000 LB HYDRAULIC EXCAVATOR)

EP 1110-1-8, Vol. 430 Nov 11

2-130


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

H25 LABOUNTY MANUFACTURING, (continued)RDG 120H25LU036 $97,925 13.06 1.06 0.00 1007.5929.47HYDRAULIC EXCAVATOR, ATTACHMENT,

MATERIAL HANDLING, ROTATING GRAPPLE, 2.00 CY (ADD 120,000-160,000 LB HYDRAULIC EXCAVATOR)

WAIN-ROY, INC.

H25WN00 $7,748 1.03 0.08 0.00 160.602.25HYDRAULIC EXCAVATOR, ATTACHMENT, MATERIAL HANDLING, BUCKET, 36" CONCRETE/PAVEMENT REMOVAL (ADD 75,000 LB HYDRAULIC EXCAVATOR)

0.23 ATTACHMENTS, CONCRETE PULVERIZERSSUBCATEGORY


CR3H25CA058 $22,879 3.24 0.24 0.00 61.868.17HYDRAULIC EXCAVATOR, ATTACHMENT, CONCRETE PULVERIZER, CRUSHER, 16.0" JAW OPENING (ADD 40,000 LB MIN HYDRAULIC EXCAVATOR)

P16H25CA059 $83,506 11.83 0.88 0.00 536.8028.59HYDRAULIC EXCAVATOR, ATTACHMENT, CONCRETE PULVERIZER, 30.0" JAW OPENING (ADD 40,000 LB MIN HYDRAULIC EXCAVATOR)



EP 1110-1-8, Vol. 430 Nov 11

2-131


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)





KENT DEMOLITION TOOLS

KF12 TLBH25KN001 $30,240 4.28 0.32 0.00 192.4610.63HYDRAULIC EXCAVATOR, ATTACHMENT, CONCRETE BREAKER, 2,000 FT-LB, W/4.25'' DIA. POINT (ADD 16,000-24,000 LB HYDRAULIC EXCAVATOR)

KF19 QTH25KN002 $41,935 5.94 0.44 0.00 313.4114.55HYDRAULIC EXCAVATOR, ATTACHMENT, CONCRETE BREAKER, 3,000 FT-LB, W/4.75'' DIA. POINT (ADD 26,000-36,000 LB HYDRAULIC EXCAVATOR)



EP 1110-1-8, Vol. 430 Nov 11

2-132


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

H25 KENT DEMOLITION TOOLS (continued)KF70 QTH25KN006 $118,638 16.81 1.25 0.00 1039.6640.77HYDRAULIC EXCAVATOR, ATTACHMENT,

CONCRETE BREAKER, 10,000 FT-LB, W/7.09 '' DIA. POINT (ADD 80,000 LB HYDRAULIC EXCAVATOR)


CP 40 CH25LU046 $35,374 5.01 0.37 0.00 292.8812.35HYDRAULIC EXCAVATOR, ATTACHMENT, CONCRETE PULVERIZER, 30" JAW OPENING (ADD 40,000 LB HYDRAULIC EXCAVATOR)

CP 60 SH25LU047 $40,681 5.76 0.43 0.00 303.3114.23HYDRAULIC EXCAVATOR, ATTACHMENT, CONCRETE PULVERIZER, 36" JAW OPENING (ADD 60,000 LB HYDRAULIC EXCAVATOR)




UP 45 SVH25LU040 $148,654 21.06 1.57 0.00 10512.1050.58HYDRAULIC EXCAVATOR, ATTACHMENT, CONCRETE PULVERIZER, CRACKING JAWS, 45" JAW OPENING (ADD 55,000 LB HYDRAULIC EXCAVATOR)

EP 1110-1-8, Vol. 430 Nov 11

2-133


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

H25 LABOUNTY MANUFACTURING, (continued)UP 75 SVH25LU041 $182,340 25.83 1.92 0.00 12714.8461.87HYDRAULIC EXCAVATOR, ATTACHMENT,

CONCRETE PULVERIZER, CRACKING JAWS, 49" JAW OPENING (ADD 80,000 LB HYDRAULIC EXCAVATOR)

UP 90H25LU042 $219,934 31.16 2.32 0.00 17117.9075.23HYDRAULIC EXCAVATOR, ATTACHMENT, CONCRETE PULVERIZER, CRACKING JAWS, 62" JAW OPENING (ADD 75,000 LB HYDRAULIC EXCAVATOR)

UP 45 SVH25LU053 $156,442 22.16 1.65 0.00 10512.7353.19HYDRAULIC EXCAVATOR, ATTACHMENT, CONCRETE PULVERIZER, 36" JAW OPENING (ADD 55,000 LB HYDRAULIC EXCAVATOR)

UP 75 SVH25LU054 $192,608 27.29 2.03 0.00 12615.6865.32HYDRAULIC EXCAVATOR, ATTACHMENT, CONCRETE PULVERIZER, 40" JAW OPENING (ADD 80,000 LB HYDRAULIC EXCAVATOR)

0.24 ATTACHMENTS, COMPACTORSSUBCATEGORY

AMERICAN COMPACTION EQUIPMENT, INC.

DC-24BLH25AX001 $8,027 1.14 0.08 0.00 250.652.69HYDRAULIC EXCAVATOR, ATTACHMENT, COMPACTOR, 23" WIDE, SHEEPS FOOT, 3 RIMS - 38" DIA (ADD 25,000-50,000 LB HYDRAULIC EXCAVATOR)

DC-24EXH25AX003 $9,971 1.41 0.11 0.00 330.823.34HYDRAULIC EXCAVATOR, ATTACHMENT, COMPACTOR, 23" WIDE, SHEEPS FOOT, 3 RIMS - 42" DIA (ADD 50,000-75,000 LB HYDRAULIC EXCAVATOR)

EP 1110-1-8, Vol. 430 Nov 11

2-134


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

H25 AMERICAN COMPACTION EQUIPMENT, INC. (continued)

DC-24EXLH25AX005 $11,785 1.67 0.12 0.00 390.963.95HYDRAULIC EXCAVATOR, ATTACHMENT, COMPACTOR, 23" WIDE, SHEEPS FOOT, 3 RIMS - 48" DIA (ADD 75,000-110,000 LB HYDRAULIC EXCAVATOR)

DC-36BLH25AX002 $9,116 1.29 0.10 0.00 330.753.06HYDRAULIC EXCAVATOR, ATTACHMENT, COMPACTOR, 35" WIDE, SHEEPS FOOT, 4 RIMS - 38" DIA (ADD 50,000-75,000 LB HYDRAULIC EXCAVATOR)

DC-36EXH25AX004 $11,664 1.65 0.12 0.00 430.953.90HYDRAULIC EXCAVATOR, ATTACHMENT, COMPACTOR, 35" WIDE, SHEEPS FOOT, 4 RIMS - 42" DIA (ADD 50,000-75,000 LB HYDRAULIC EXCAVATOR)

DC-36EXLH25AX006 $14,877 2.11 0.16 0.00 531.224.99HYDRAULIC EXCAVATOR, ATTACHMENT, COMPACTOR, 36" WIDE, SHEEPS FOOT, 4 RIMS - 48" DIA (ADD 75,000-110,000 LB HYDRAULIC EXCAVATOR)


KHP-35 ME-SH25KN007 $6,088 0.86 0.06 0.00 40.492.18HYDRAULIC EXCAVATOR, ATTACHMENT, COMPACTOR, 12" X 26" PLATE, 3000 LB FORCE (ADD 14,000-25,000 LB HYDRAULIC EXCAVATOR)

KHP-135FT - IIH25KN009 $12,642 1.79 0.13 0.00 141.034.38HYDRAULIC EXCAVATOR, ATTACHMENT, COMPACTOR, 28" X 40" PLATE, 13500 LB FORCE (ADD 25,000-50,000 LB HYDRAULIC EXCAVATOR)

KHP-210FT - IIH25KN010 $17,439 2.47 0.18 0.00 231.425.99HYDRAULIC EXCAVATOR, ATTACHMENT, COMPACTOR, 34" X 46" PLATE, 21000 LB FORCE (ADD 40,000-75,000 LB HYDRAULIC EXCAVATOR)

EP 1110-1-8, Vol. 430 Nov 11

2-135


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

WAIN-ROY, INC.

24-3 (15-22.5 TON)

H25WN00 $8,254 1.17 0.09 0.00 220.682.77HYDRAULIC EXCAVATOR, ATTACHMENT, COMPACTOR, 24'' WIDE, SHEEPSFOOT, 3 RIMS - 33" DIA (ADD 15-22.5 TON HYDRAULIC EXCAVATOR)

36-4 (15-22.5 TON)

H25WN00 $9,058 1.28 0.10 0.00 260.743.04HYDRAULIC EXCAVATOR, ATTACHMENT, COMPACTOR, 36'' WIDE, SHEEPSFOOT, 4 RIMS - 33" DIA (ADD 15-22.5 TON HYDRAULIC EXCAVATOR)

24-3 (22.5-30 TON)

H25WN00 $9,908 1.40 0.10 0.00 310.803.31HYDRAULIC EXCAVATOR, ATTACHMENT, COMPACTOR, 24'' WIDE, SHEEPSFOOT, 3 RIMS - 39" DIA (ADD 22.5-30 TON HYDRAULIC EXCAVATOR)

36-4 (22.5-30 TON)

H25WN00 $11,255 1.59 0.12 0.00 380.923.77HYDRAULIC EXCAVATOR, ATTACHMENT, COMPACTOR, 36'' WIDE, SHEEPSFOOT, 4 RIMS - 39" DIA (ADD 22.5-30 TON HYDRAULIC EXCAVATOR)

HYDRAULIC EXCAVATORS, WHEEL MOUNTEDH300.01 0 THRU 1.0 CYSUBCATEGORY


151M318DH30CA005 $202,501 18.41 2.20 14.89 39311.4152.98HYDRAULIC EXCAVATORS, WHEEL, 33,700 LBS, 1.00 CY BUCKET, 1-PIECE BOOM, 19' DIGGING DEPTH, 4X4

HP D-off

121M315DH30CA007 $171,353 15.14 1.86 11.93 3529.4344.83HYDRAULIC EXCAVATORS, WHEEL, 35,100 LBS, 0.70 CY BUCKET, 1-PIECE BOOM, 17' 7" DIGGING DEPTH, 4X4X2

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-136


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

GRADALL COMPANY

233XL4100 IIIH30GA006 $297,902 27.33 3.23 22.97 47516.9078.56D-onHYDRAULIC EXCAVATORS, WHEEL, 44,851 LBS, 0.75 CY BUCKET, TELESCOPIC BOOM, 22' 6" DIGGING DEPTH, 6X4

HP D-off

138XL 3300 IIIH30GA007 $223,420 20.57 2.43 13.61 39312.7254.66HYDRAULIC EXCAVATORS, WHEEL, 15,270 LBS, 0.68 CY BUCKET, TELESCOPIC BOOM, 4X4X2

HP D-off

0.02 OVER 1.0 CYSUBCATEGORY

GRADALL COMPANY

163XL 5100 IIIH30GA008 $334,408 24.00 3.57 20.56 55015.5779.25230 HP D-onHYDRAULIC EXCAVATORS, WHEEL, 22,800 LBS, 1.25 CY BUCKET, TELESCOPIC BOOM, 25' 4" DIGGING DEPTH, 6X4

HP D-off


123PW170ES-6H30KM001 $248,095 18.32 2.65 12.13 37611.8152.02HYDRAULIC EXCAVATORS, WHEEL, 37,600 LBS, 1.12 CY BUCKET, 1-PIECE BOOM, 18' 8" DIGGING DEPTH, 4X4

HP D-off

HYDRAULIC SHOVELS, CRAWLER MOUNTEDH350.12 DIESEL, OVER 5.0 CYSUBCATEGORY

HITACHI CONSTRUCTION MACHINERY

641EX1200-5H35HI006 $1,369,108 68.46 13.73 67.56 2,44747.96264.83HYDRAULIC SHOVEL, CRAWLER, 8.5 CY BUCKET, FRONT SHOVEL, 17' 3" DIGGING DEPTH

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-137


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

O & K ORENSTEIN & KOPPEL INC.

607RH 40 EH35OK001 $1,078,391 53.92 10.82 63.98 2,20437.78219.93HYDRAULIC SHOVEL, CRAWLER, 9.20 CY BUCKET, BACKHOE, 28' 10" DIGGING DEPTH

HP D-off

1,018RH 90 CH35OK003 $2,139,876 106.99 21.47 107.30 3,59474.97415.72HYDRAULIC SHOVEL, CRAWLER, 13.10 CY BUCKET, BACKHOE, 31' 1" DIGGING DEPTH

HP D-off

1,280RH 120 EH35OK004 $3,559,294 177.96 35.71 134.91 5,842124.69645.60HYDRAULIC SHOVEL, CRAWLER, 17.00 CY BUCKET, FRONT SHOVEL, 7' 7" DIGGING DEPTH

HP D-off

2,250RH 200H35OK005 $6,997,365 349.87 70.20 237.15 10,582245.141,239.65HYDRAULIC SHOVEL, CRAWLER, 34.00 CY BUCKET, BACKHOE, 30' 6" DIGGING DEPTH

HP D-off

LAND CLEARING EQUIPMENTL100.00 LAND CLEARING EQUIPMENTSUBCATEGORY

BALDERSON, INC.

BBL7L10BS004 $27,383 2.19 0.28 0.00 241.385.41LAND CLEARING EQUIPMENT, ROCK & ROOT RAKE, 12.0' WIDE, 9 TEETH (ADD 200 - 250 HP TRACTOR DOZER)

BRK8L10BS005 $40,304 3.22 0.42 0.00 722.037.90LAND CLEARING EQUIPMENT, ROCK & ROOT RAKE 12.5' WIDE, 9 TEETH (ADD D8 TRACTOR DOZER 275 - 325 HP)

BMA8L10BS002 $40,235 3.22 0.42 0.00 682.037.89LAND CLEARING EQUIPMENT, MULTI-APPLICATION RAKE, 12.5' WIDE, 9 TEETH (ADD D8 TRACTOR DOZER 275 - 325 HP)

EP 1110-1-8, Vol. 430 Nov 11

2-138


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

L10 BALDERSON, INC. (continued)BLF988DTCL10BS007 $29,085 2.33 0.30 0.00 901.475.99LAND CLEARING EQUIPMENT, LOGGING

FORK, 92" TINES (ADD 400 - 450 HP FE LOADER)

BUSH HOG

SM-60L10BU005 $9,871 0.79 0.10 0.00 170.502.96LAND CLEARING EQUIPMENT, ROTARY CUTTER, 5' WIDE-SIDE MTD (ADD FARM 50 HP TRACTOR)

287L10BU010 $4,112 0.33 0.04 0.00 110.211.57LAND CLEARING EQUIPMENT, ROTARY CUTTER, 7' WIDE, 1.5 - 12" HEIGHT (ADD FARM 40 HP TRACTOR)

3210L10BU011 $8,254 0.66 0.09 0.00 250.423.06LAND CLEARING EQUIPMENT, ROTARY CUTTER, 10.5' WIDE, 2 - 14" HEIGHT (ADD FARM 70 HP TRACTOR)

3715L10BU012 $16,912 1.35 0.17 0.00 500.855.18LAND CLEARING EQUIPMENT, ROTARY CUTTER, 15' WIDE, 2 - 14" HEIGHT (ADD FARM 80 HP TRACTOR)

2720L10BU013 $20,478 1.64 0.21 0.00 561.036.36LAND CLEARING EQUIPMENT, ROTARY CUTTER, 20' WIDE, 2 - 14" HEIGHT (ADD FARM 90 HP TRACTOR)

ROME PLOW CO.

RV8NL10RM001 $53,614 4.29 0.55 0.00 1342.7010.50LAND CLEARING EQUIPMENT, V-TREE CUTTER (ADD 275 - 325 HP TRACTOR DOZER)

MA-152R-8SL10RM002 $48,344 3.87 0.50 0.00 1502.449.12LAND CLEARING EQUIPMENT, MULTI-APPLICATION RAKE, 12' 8'' WIDE, 9 TEETH (ADD 275 - 325 HP TRACTOR DOZER)

EP 1110-1-8, Vol. 430 Nov 11

2-139


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)


27SC 252L10VE010 $13,415 1.06 0.14 5.26 110.678.49LAND CLEARING EQUIPMENT, STUMPER, 16" DIA WHEEL, TRAILER MTD

HP G


HP G


HP D-off

13TS-30L10VE005 $13,055 1.01 0.13 2.53 380.645.33LAND CLEARING EQUIPMENT, TREE SPADE, 30" DIA, 26" DEPTH, TRAILER MTD

HP G

20TS-44AL10VE006 $34,156 2.70 0.35 3.90 661.7010.87LAND CLEARING EQUIPMENT, TREE SPADE, 44" DIA, 40" DEPTH, TRAILER MTD

HP G

TS-50L10VE007 $29,383 2.35 0.30 0.00 811.487.04LAND CLEARING EQUIPMENT, TREE SPADE, 50" DIA, 48" DEPTH (ADD 13,800 GVW TRUCK)

LANDSCAPING EQUIPMENTL150.00 LANDSCAPING EQUIPMENTSUBCATEGORY

BOWIE INDUSTRIES, INC.

25LANCER 500L15BW001 $20,093 4.19 0.23 6.50 252.3315.51LANDSCAPING EQUIPMENT, 500 GAL, HYDROMULCHER, TRAILER MTD

HP G

35VICTOR 800L15BW002 $36,891 7.68 0.42 9.10 484.2625.34LANDSCAPING EQUIPMENT, 800 GAL, HYDROMULCHER, TRAILER MTD

HP G

50VICTOR 1100L15BW003 $42,410 8.85 0.48 13.00 604.9131.94LANDSCAPING EQUIPMENT, 1,100 GAL, HYDROMULCHER, GOOSENECK TRAILER MTD

HP G

EP 1110-1-8, Vol. 430 Nov 11

2-140


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

L15 BOWIE INDUSTRIES, INC. (continued)90IMPERIAL 3000L15BW004 $61,810 13.13 0.70 11.63 887.2738.57LANDSCAPING EQUIPMENT, 3,000 GAL,

HYDROMULCHER, TRUCK MTD (ADD 55,000 GVW TRUCK)

HP D-off

FINN CORPORATION

115T330L15FG001 $195,888 41.63 2.20 21.18 9623.02104.91310 HP D-offLANDSCAPING EQUIPMENT, 3,000 GAL, HYDROSEEDER, TRUCK MTD (INCLUDES 56,000 GVW TRUCK)

HP D-off

115B260TL15FG002 $44,926 9.43 0.51 14.86 485.2335.07LANDSCAPING EQUIPMENT, MULCHER, STRAW BLOWER, 20 TONS PER HOUR, TRAILER MOUNTED

HP D-off

HUSQVARNA FOREST & GARDEN CO.

10CRT1350LSL15HV002 $1,290 0.27 0.01 2.60 30.153.40LANDSCAPING EQUIPMENT, ROTOTILLER, 21" WIDTH BY 7" DEPTH

HP G

HOFFCO-COMET

3PH980EL15HZ001 $852 0.18 0.01 0.78 10.101.21POST HOLE DRILL, UP TO 8" DIA, 30" DEEP, ONE MAN OPERATION

HP G

DEERE & COMPANY

20F725L15JD001 $11,585 1.53 0.13 5.20 120.9011.20LANDSCAPING EQUIPMENT, LAWNMOWER, 54" DECK, SIDE DISCHARGE RIDING, 4X2

HP G

MX5L15JD005 $2,322 0.49 0.03 0.00 80.280.97LANDSCAPING EQUIPMENT, ROTARY MOWER, 60" WIDE, MEDIUM DUTY, PTO DRIVE (ADD 45 - 100 HP AGRICULTURAL TRACTOR)

EP 1110-1-8, Vol. 430 Nov 11

2-141


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

L15 DEERE & COMPANY (continued)609L15JD006 $4,306 0.92 0.05 0.00 120.511.80LANDSCAPING EQUIPMENT, ROTARY

MOWER, 60" WIDE, HEAVY DUTY, PTO DRIVE (ADD 45 - 100 HP AGRICULTURAL TRACTOR)

TORO

622188 - PRO-LINE 21"

L15TO001 $1,385 0.29 0.02 1.56 10.172.30LANDSCAPING EQUIPMENT, LAWNMOWER, 21" DECK, REAR BAGGER, PUSH MOWER

HP G

1530092 MID-SIZEL15TO002 $4,217 0.82 0.05 3.90 60.466.14LANDSCAPING EQUIPMENT, LAWNMOWER, 32" DECK, SIDE DISCHARGE, WALK BEHIND MOWER

HP G

2174448L15TO003 $8,109 1.65 0.09 5.46 120.929.49LANDSCAPING EQUIPMENT, LAWNMOWER, 48" DECK, SIDE DISCHARGE, RIDING MOWER

HP G

2174449L15TO004 $8,653 1.77 0.10 5.46 130.999.69LANDSCAPING EQUIPMENT, LAWNMOWER, 52" DECK W/Z100 TRACTOR, SIDE DISCHARGE, RIDING MOWER

HP G

2974253L15TO006 $15,988 3.27 0.18 7.54 151.8215.12LANDSCAPING EQUIPMENT, LAWNMOWER, 60" DECK W/Z500 TRACTOR, SIDE DISCHARGE, RIDING MOWER

HP G

2974254L15TO007 $16,497 3.38 0.19 7.54 171.8815.34LANDSCAPING EQUIPMENT, LAWNMOWER, 72" DECK, W/Z500 TRACTOR, SIDE DISCHARGE, RIDING MOWER

HP G

10POWER MAX 11280XE

L15TO010 $1,954 0.42 0.02 2.60 30.233.69LANDSCAPING EQUIPMENT, SNOWBLOWER, 28" PATH, 45' THROW

HP G

EP 1110-1-8, Vol. 430 Nov 11

2-142


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

WILLMAR EQUIPMENT COMPANY

S-200L15WI001 $8,714 1.75 0.10 0.00 150.983.63LANDSCAPING EQUIPMENT, SPREADER, 70 CF DRY CHEMICAL (ADD 55 HP FARM TRACTOR)

LIGHTING SETS, TRAILER MOUNTEDL200.10 METALLIC VAPORSUBCATEGORY

ALLMAND BROTHERS INC.

13MAXI-LITE 7.5/8L20AB017 $14,192 1.39 0.15 1.87 210.856.56LITE SET, TRAILER MTD., 4/1250W, W/7.5 KW GEN, ELECTRIC MAST WINCH

HP D-off

14MAXI-LITE 7.5/8 CSA

L20AB018 $15,804 1.55 0.17 1.99 210.957.20LITE SET, TRAILER MTD., 4/1,000W, W/8 KW GEN, ELECTRIC MAST WINCH

HP D-off

14MAXI-LITE 7.5/8 CSA

L20AB019 $18,525 1.82 0.19 1.99 211.108.05LITE SET, TRAILER MTD., 6/1,000W, W/8 KW GEN, ELECTRIC MAST WINCH

HP D-off

12NIGHT-LITE PRO

L20AB020 $11,974 1.17 0.13 1.60 200.725.56LITE SET, TRAILER MTD., 4/1,000W, W/6 KW GEN, MANUAL MAST WINCH

HP D-off

14NIGHT-LITE PRO CSA

L20AB021 $12,651 1.24 0.13 1.99 200.756.20LITE SET, TRAILER MTD., 4/1,000W, W/8 KW GEN, MANUAL MAST WINCH

HP D-off

13NIGHT-LITE PR0 V

L20AB022 $14,271 1.40 0.15 1.87 210.856.58LITE SET, TRAILER MTD., 4/1,000W, W/7.5 KW GEN, ELECTRIC MAST WINCH

HP D-off

ECLIPSE 2220/SE ALT

L20AB023 $5,870 0.57 0.06 0.00 120.351.86LITE SET, TRAILER MTD., 15 LED LAMP, FLASHING ARROW, W/TWO 8D BATTERIES AND 50W SOLAR ARRAY

ECLIPSE 2220/SE APF

L20AB024 $6,286 0.61 0.07 0.00 120.381.99LITE SET, TRAILER MTD., 25 LED LAMP, FLASHING ARROW, W/TWO 8D BATTERIES AND 50W SOLAR ARRAY

EP 1110-1-8, Vol. 430 Nov 11

2-143


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

LINE STRIPING EQUIPMENTL250.00 LINE STRIPING EQUIPMENTSUBCATEGORY

JCL EQUIPMENT CO.

134-BL25JE001 $12,197 1.22 0.13 3.61 150.747.35LINE STRIPING EQUIPMENT, STRIPER, INTERMEDIATE, 2 GUNS, SELF PROPELLED, SINGLE COLOR

HP G

230ROAD RUNNERL25JE002 $103,911 10.25 1.09 32.06 1166.2264.14LINE STRIPING EQUIPMENT, STRIPER, INTERMEDIATE, 3 GUNS, TRUCK MOUNTED (11,000 LB GVW), TWO COLORS

HP D-off

M-B COMPANIES, INC.

55-10L25MB002 $6,470 0.52 0.07 1.39 60.334.40LINE STRIPING EQUIPMENT, STRIPER, 1 GUN, WALK-BEHIND, SINGLE COLOR

HP G

105-12AL25MB005 $11,794 1.05 0.12 2.78 60.657.38LINE STRIPING EQUIPMENT, STRIPER, 2 GUNS, WALK BEHIND, SINGLE COLOR

HP G

23220L25MB007 $54,934 5.49 0.58 6.39 303.3323.19LINE STRIPING EQUIPMENT, STRIPER, INTERMEDIATE, 3-4 GUNS, SELF PROPELLED, THREE COLORS

HP G

60245L25MB006 $97,869 9.79 1.03 16.68 485.9346.63LINE STRIPING EQUIPMENT, STRIPER, INTERMEDIATE, 3 GUNS, SELF PROPELLED, TWO COLORS

HP G

190VANMARK 360L25MB004 $161,068 15.97 1.70 52.81 1339.69104.33LINE STRIPING EQUIPMENT, STRIPER, INTERMEDIATE, 3-4 GUNS, W/11,000 LBS GVW TRUCK, TWO COLORS

HP G

EP 1110-1-8, Vol. 430 Nov 11

2-144


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

L25 M-B COMPANIES, INC. (continued)190360L25MB008 $176,063 17.20 1.85 26.49 8010.4579.49LINE STRIPING EQUIPMENT, STRIPER,

INTERMEDIATE, 3-4 GUNS, THERMAL 120 GAL, TRUCK MTD, TWO COLORS

HP D-off

LOADERS, BELT (Conveyor belts) & ACCESSORIESL300.00 LOADERS, BELT (Conveyor belts) & ACCESSORIESSUBCATEGORY

HEWITT-ROBINS

25V-11 6X16FT, TDL30HW015 $149,344 11.65 1.54 1.32 1387.3732.17LOADER, CONVEYOR BELT & ACCESSORIES, SCREENING PLANT, W/6' X 16' VIBRATORY SLOPE TRIPLE DECK SCREENS/36"X 16.5' UNDER SCREEN CONVEYOR/ 7 CY HOPPER/ & FEEDER

HP E


1511-2450L30KB001 $35,485 2.74 0.37 0.79 571.748.38LOADER, CONVEYOR BELT & ACCESSORIES, COVEYOR 50', MOBILE, CONCRETE & AGGREGATE, 24'' WIDE

HP E

1511-2460L30KB002 $37,377 2.89 0.39 0.79 621.848.75LOADER, CONVEYOR BELT & ACCESSORIES, CONVEYOR, 60', MOBILE, CONCRETE & AGGREGATE, 24'' WIDE

HP E

METSO MINERALS

25CV50DL30RA001 $76,671 6.03 0.79 2.64 1303.8118.41LOADER, CONVEYOR BELT & ACCESSORIES, GRIZZLY SINGLE SCREEN, 40 CY/HR TRAILER MTD

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-145


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

SUPERIOR INDUSTRIES, AN ASTEC COMPANY

1536''X35' FEED CONVEY

L30S4001 $19,474 1.56 0.20 0.79 330.985.08LOADER, CONVEYOR BELT & ACCESSORIES, BELT FEEDER

HP E

RUN-ON HYDRAULIC LEG

L30S4002 $22,247 1.78 0.23 0.00 281.124.45LOADER, CONVEYOR BELT & ACCESSORIES, 4 HYDRAULIC JACK LEGS

SIDE SKIRTING UPPER

L30S4003 $1,635 0.13 0.02 0.00 90.090.33LOADER, CONVEYOR BELT & ACCESSORIES, SIDE GUARD, ONE SIDE, UPPER

SIDE SKIRTING LOWER

L30S4004 $2,766 0.22 0.03 0.00 90.140.55LOADER, CONVEYOR BELT & ACCESSORIES, SIDE GUARD, ONE SIDE, LOWER

TELSMITH INC.

12PTC 24IN X 50FT

L30TS001 $39,997 2.98 0.41 0.63 101.909.20LOADER, CONVEYOR BELT & ACCESSORIES, CONVEYOR, TRUSS FRAME, 24"W X 50'L, WHEEL MTD, 300 TPH

HP E

LOADERS, FRONT END, CRAWLER TYPEL350.00 LOADERS, FRONT END, CRAWLER TYPESUBCATEGORY


90939-CL35CA013 $129,062 10.32 1.33 10.40 2096.4938.63LOADER, FRONT END, CRAWLER, 1.50 CY BUCKET

HP D-off

148953-DL35CA005 $212,343 16.99 2.19 17.11 33410.6963.57LOADER, FRONT END, CRAWLER, 2.25 CY BUCKET

HP D-off

160963-DL35CA014 $289,990 23.20 2.99 18.50 43314.5981.43LOADER, FRONT END, CRAWLER, 3.20 CY BUCKET

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-146


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

L35 CATERPILLAR INC. ( MACHINE DIVISION) (continued)

242973-CL35CA007 $401,120 32.09 4.14 27.98 58120.19115.28LOADER, FRONT END, CRAWLER, 3.70 CY BUCKET

HP D-off


200D75S-5L35KM006 $470,906 37.67 4.86 23.12 48523.70124.59LOADER, FRONT END, CRAWLER, 3.30 CY BUCKET

HP D-off

LOADERS, FRONT END, WHEEL TYPEL400.11 ARTICULATED, 0 THRU 225 HPSUBCATEGORY


52904BL40CA032 $48,601 3.74 0.52 5.48 982.3914.98LOADER, FRONT END, WHEEL, 0.80 CY BUCKET, ARTICULATED, 4X4

HP D-off

68906L40CA033 $63,820 4.98 0.68 7.17 1093.1719.53LOADER, FRONT END, WHEEL, 1.00 CY BUCKET, ARTICULATED, 4X4

HP D-off

76908L40CA034 $74,671 5.32 0.80 8.01 1333.4626.16LOADER, FRONT END, WHEEL, 1.30 CY BUCKET, ARTICULATED, 4X4

HP D-off

95914GL40CA019 $104,648 8.16 1.12 10.01 1755.2030.75LOADER, FRONT END, WHEEL, 1.70 CY BUCKET, ARTICULATED, 4X4

HP D-off

128924HzL40CA022 $145,285 11.46 1.56 13.49 2427.2941.72LOADER, FRONT END, WHEEL, 2.20 CY BUCKET, ARTICULATED, 4X4

HP D-off

149928HzL40CA015 $144,024 11.36 1.55 15.70 2767.2343.97LOADER, FRONT END, WHEEL, 2.60 CY BUCKET, ARTICULATED, 4X4

HP D-off

180938HL40CA023 $177,402 13.27 1.90 18.97 3328.5456.67LOADER, FRONT END, WHEEL, 3.65 CY BUCKET, ARTICULATED, 4X4

HP D-off


HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-147


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

L40 CATERPILLAR INC. ( MACHINE DIVISION) (continued)


HP D-off

CASE CORPORATION

136621DL40CS009 $162,462 12.16 1.74 14.33 2617.8248.51LOADER, FRONT END, WHEEL, 2.5 CY BUCKET, ARTICULATED, 4X4

HP D-off

181721DL40CS010 $193,721 14.69 2.08 19.08 3069.4359.26LOADER, FRONT END, WHEEL, 3.0 CY BUCKET, ARTICULATED, 4X4

HP D-off

187821CL40CS011 $244,640 18.51 2.63 19.71 37911.8970.15LOADER, FRONT END, WHEEL, 3.5 CY BUCKET, ARTICULATED, 4X4

HP D-off


75WA95-3L40KM015 $91,234 7.07 0.98 7.91 1284.5225.40LOADER, FRONT END, WHEEL, 1.40 CY BUCKET, ARTICULATED, 4X4

HP D-off


HP D-off

0.12 ARTICULATED, OVER 225 HPSUBCATEGORY



HP D-off

627990 HL40CA018 $1,349,636 76.12 13.65 66.09 1,71651.71248.06LOADER, FRONT END, WHEEL, 11.00 CY BUCKET, ARTICULATED, 4X4

HP D-off

800992-KL40CA009 $1,863,760 103.34 18.84 84.32 2,15070.51338.01LOADER, FRONT END, WHEEL, 16.00 CY BUCKET, ARTICULATED, 4X4

HP D-off

501988HL40CA035 $797,782 43.10 8.07 52.81 1,09229.62173.33LOADER, FRONT END, WHEEL, 9.00 CY BUCKET, ARTICULATED, 4X4

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-148


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT



HP D-off

490WA600-6L40KM009 $649,407 35.38 6.57 51.65 1,01924.26142.96LOADER, FRONT END, WHEEL, 8.00 CY BUCKET, ARTICULATED, 4X4

HP D-off

684WA700-3AL40KM010 $884,019 48.53 8.94 72.09 1,57433.21195.91LOADER, FRONT END, WHEEL, 11.10 CY BUCKET, ARTICULATED, 4X4

HP D-off

853WA800-3L40KM011 $1,463,101 79.60 14.79 89.91 2,23054.59293.59LOADER, FRONT END, WHEEL, 13.10 CY BUCKET, ARTICULATED, 4X4

HP D-off

0.20 SKID STEERSUBCATEGORY


49216BL40CA028 $32,284 3.09 0.34 5.66 541.8914.01LOADER, FRONT END, WHEEL, SKID-STEER, 13.0 CF, 60" BUCKET, 4X4

HP D-off


HP D-off


HP D-off

74246CL40CA031 $39,476 3.76 0.42 8.55 742.3018.99LOADER, FRONT END, WHEEL, SKID-STEER, 15.4 CF, 72" BUCKET, 4X4

HP D-off

MELROE COMPANY/BOBCAT

24S70L40ME016 $17,398 1.67 0.18 2.72 281.027.15LOADER, FRONT END, WHEEL, SKID-STEER, 6.5 CF, 44" BUCKET, 4X4

HP D-off


HP D-off

46S175L40ME012 $28,288 2.75 0.30 5.32 621.6812.49LOADER, FRONT END, WHEEL, SKID-STEER, 14.3 CF, 60" BUCKET

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-149


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

L40 MELROE COMPANY/BOBCAT (continued)49S130L40ME021 $24,771 2.23 0.26 5.66 521.3812.79LOADER, FRONT END, WHEEL, SKID-

STEER, 13.0 CF, 54" BUCKET, 4X4 HP D-off


HP D-off


HP D-off

0.31 TOOL CARRIER & TELESCOPIC HANDLERS, 0 THRU 225 HPSUBCATEGORY


90IT14GL40CA013 $122,478 8.89 1.31 9.49 1805.7633.77LOADER, WHEEL, INTEGRATED TOOL CARRIER, 1.75 CY LOADER; 6,303 LB @ 12.17' HIGH, FORK LIFT, OR 1,841 LB @ 22.42' HIGH, MATERIAL HANDLING ARM

HP D-off

145IT38HL40CA012 $195,304 14.35 2.08 15.28 2799.2653.20LOADER, WHEEL, INTEGRATED TOOL CARRIER, 2.50 CY LOADER; 10,640 LB @ 12.58' HIGH FORK LIFT, OR 3,195 LB @ 23.25' HIGH, MATERIAL HANDLING ARM

HP D-off

200IT62G IIL40CA014 $271,976 20.04 2.90 21.08 45412.9273.62LOADER, WHEEL, INTEGRATED TOOL CARRIER, 4.25 CY LOADER; 13,670 LB @ 12.42' HIGH, FORK LIFT, OR 5,040 LB @ 22.67' HIGH, MATERIAL HANDLING ARM

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-150


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

LOADERS / BACKHOE, WHEEL TYPEL500.00 LOADERS / BACKHOE, WHEEL TYPESUBCATEGORY


78416EL50CA001 $64,387 4.56 0.69 6.36 1622.9720.91LOADER / BACKHOE, WHEEL, 1.00 CY FRONT END BUCKET, 18" DIP, 4.5 CF, 14.5' DIGGING DEPTH, 4X2

HP D-off

110446DL50CA004 $154,301 11.10 1.65 8.98 1937.2040.61LOADER / BACKHOE, WHEEL, 1.50 CY FRONT END BUCKET, 36" DIP, 19 CF, 17.1' DIGGING DEPTH, 4X2

HP D-off

CASE CORPORATION

90580 SUPER M SERIES 2

L50CS005 $97,570 7.03 1.04 7.34 1434.5628.10LOADER / BACKHOE, WHEEL, 1.00 CY FRONT END BUCKET, 24" DIP, 6.2 CF, 14.25' DIGGING DEPTH, 4X4

HP D-off

98590 SUPER M SERIES 2

L50CS006 $117,271 8.38 1.25 8.00 1535.4432.74LOADER / BACKHOE, WHEEL, 1.30 CY FRONT END BUCKET, 24" DIP, 6.4 CF, 18' DIGGING DEPTH, 4X4, EXTENDAHOE

HP D-off

JCB INC.

67212S (4WS)L50JC001 $73,731 5.33 0.79 5.47 1203.4621.17LOADER / BACKHOE, WHEEL, 0.80 CY FRONT END BUCKET, 24" DIP, 4.3 CF, 12' DIGGING DEPTH, 4X4

HP D-off

92214S (2WD)L50JC002 $84,156 6.00 0.90 7.51 1583.9026.06LOADER / BACKHOE, WHEEL, 1.25 CY FRONT END BUCKET, 24" DIP, 7.1 CF, 14.6' DIGGING DEPTH, 4X2

HP D-off

100214S (4WS)L50JC003 $102,111 7.26 1.09 8.16 1644.7230.45LOADER / BACKHOE, WHEEL, 1.40 CY FRONT END BUCKET, 24" DIP, 7.1 CF, 14.6' DIGGING DEPTH, 4X4

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-151


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

L50 JCB INC. (continued)100215S (4WS)L50JC005 $118,304 8.47 1.26 8.16 1765.5033.25LOADER / BACKHOE, WHEEL, 1.40 CY

FRONT END BUCKET, 24" DIP, 7.1 CF, 20.1' DIGGING DEPTH, 4X4

HP D-off

100217S (4WS)L50JC007 $151,292 10.88 1.61 8.16 1787.0539.07LOADER / BACKHOE, WHEEL, 1.60 CY FRONT END BUCKET, 24" DIP, 7.1 CF, 21.5' DIGGING DEPTH, 4X4

HP D-off

LOADER / BACKHOE, ATTACHMENTSL550.00 LOADER / BACKHOE, ATTACHMENTSSUBCATEGORY


175KB-555L55KN001 $7,250 0.97 0.08 0.00 60.572.90LOADER / BACKHOE, ATTACHMENT, AIR RAM, 500 FT-LB, W/2.5" DIA. POINT (ADD 175 CFM COMPRESSOR & LDR/BH)

CFM A

250KB-999L55KN002 $14,845 1.98 0.16 0.00 101.155.92LOADER / BACKHOE, ATTACHMENT, AIR RAM, 1000 FT-LB, W/ 3.5" DIA. POINT (ADD 250 CFM COMPRESSOR & LDR/BH)

CFM A

KF6TLBL55KN004 $13,752 1.83 0.15 0.00 71.074.50LOADER / BACKHOE, ATTACHMENT, HYDRA RAM, 1000 FT-LB, W/3'' DIA. POINT (ADD 12,000-14,000 LB LDR/BH)

KF9TLBL55KN005 $20,297 2.71 0.22 0.00 111.586.64LOADER / BACKHOE, ATTACHMENT, HYDRA RAM, 1500 FT-LB, W/3.5'' DIA. POINT (ADD 14,000-20,000 LB LDR/BH)

KF12TLBL55KN006 $30,240 4.03 0.33 0.00 192.359.89LOADER / BACKHOE, ATTACHMENT, HYDRA RAM, 2000 FT-LB, W/4.25'' DIA. POINT (ADD 20,000-30,000 LB LDR/BH)

EP 1110-1-8, Vol. 430 Nov 11

2-152


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

LOG SKIDDERSL600.00 LOG SKIDDERSSUBCATEGORY


120517 GRAPPLEL60CA014 $313,540 26.65 3.13 12.65 40516.4668.04LOG SKIDDER, 8 SF GRAPPLE, CABLE 41,050 LBS LINE-PULL AND WINCH, CRAWLER

HP D-off

160525 CL60CA013 $334,060 27.47 3.34 16.86 35817.0877.77LOG SKIDDER, 11 SF GRAPPLE, CABLE 43,000 LBS LINE-PULL AND WINCH, WHEEL, 4X2

HP D-off

150527 CABLEL60CA010 $364,070 30.95 3.63 15.81 40719.1180.26LOG SKIDDER, CABLE, 69,200 LBS LINE-PULL AND WINCH, BLADE, CRAWLER

HP D-off

150527 GRAPPLEL60CA011 $397,816 33.81 3.97 15.81 47320.8886.05LOG SKIDDER, 10 SF GRAPPLE, CABLE 69,200 LBS LINE-PULL AND WINCH, CRAWLER

HP D-off

DEERE & COMPANY

119540G II - SKIDDER

L60JD001 $168,817 13.32 1.69 12.54 2198.3545.46LOG SKIDDER, CABLE, 40,525 LBS LINE-PULL WINCH AND BLADE, WHEEL, 4X4

HP D-off

119548G III - GRAPPLE

L60JD003 $164,758 12.97 1.64 12.54 2178.1344.75LOG SKIDDER, 8.0 SF GRAPPLE WITH BLADE, WHEEL, 4X4

HP D-off

160648G III - GRAPPLE

L60JD004 $218,445 16.95 2.18 16.86 26610.6660.18LOG SKIDDER, 10.4 SF GRAPPLE WITH BLADE, WHEEL, 4X4

HP D-off

151640G III - SKIDDER

L60JD002 $200,143 15.98 2.00 15.92 2399.9954.63LOG SKIDDER, CABLE, 48,867 LBS LINE-PULL WINCH AND BLADE, WHEEL, 4X4

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-153


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

L60 DEERE & COMPANY (continued)170643HL60JD006 $264,000 21.07 2.64 17.92 32013.1868.64LOG SKIDDER, LOG FELLER/BUNCHER,

18" DIA TREE SAW CUTTER, WHEEL, 4X4

HP D-off

170653GL60JD008 $379,598 32.27 3.79 17.92 41019.9385.31LOG SKIDDER, LOG FELLER/BUNCHER, 28" DIA TREE SAW CUTTER, CRAWLER

HP D-off

200843GL60JD007 $288,786 23.17 2.88 21.08 32314.4776.44LOG SKIDDER, LOG FELLER/BUNCHER, 20" DIA TREE SAW CUTTER, WHEEL, 4X4

HP D-off

MARINE EQUIPMENT (NON DREDGING)M100.41 WORK FLOATS (NON-DREDGING)SUBCATEGORY

MARINE INLAND FABRICATORS

BARGE 40'x8'x4'M10MZ001 $22,978 3.45 0.24 0.00 1431.975.85MARINE EQUIPMENT, WORK BARGE, SECTIONAL, MEDIUM DUTY, 40' X 8' X 4', 23 TON

BARGE 40'x10'x4'

M10MZ003 $26,915 4.04 0.28 0.00 1732.306.85MARINE EQUIPMENT, WORK BARGE, SECTIONAL, MEDIUM DUTY, 40' X 10' X 4', 30 TON

0.42 WORK BARGES (SECTIONAL, NON-DREDGING)SUBCATEGORY


BARGE 40'x12'x4'

M10MZ005 $30,678 0.92 0.28 0.00 1930.741.89MARINE EQUIPMENT, WORK BARGE, SECTIONAL, MEDIUM DUTY', 40' X 12' X 4', 36 TON

BARGE 40'x12'x5'

M10MZ007 $33,827 1.01 0.31 0.00 2170.822.08MARINE EQUIPMENT, WORK BARGE, SECTIONAL, MEDIUM DUTY, 40' X 12' X 5', 51 TON

EP 1110-1-8, Vol. 430 Nov 11

2-154


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT


M10XX001 $6,652 0.20 0.06 0.00 10.160.41MARINE EQUIPMENT, WORK BARGE, SECTIONAL, BOW AND STERN SECTIONS

M10XX002 $20,677 0.62 0.19 0.00 10.501.28MARINE EQUIPMENT, WORK BARGE, SECTIONAL, LOADING RAMPS

M10XX003 $24,972 0.75 0.23 0.00 10.611.54MARINE EQUIPMENT, WORK BARGE, SECTIONAL, MID-SECTION, 20' X 10' X 5'

M10XX004 $40,464 1.21 0.37 0.00 10.982.49MARINE EQUIPMENT, WORK BARGE, SECTIONAL, MID-SECTION, 40' X 10' X 5'

0.45 FLAT-DECK OR CARGO BARGE (NON-DREDGING)SUBCATEGORY


M10XX005 $174,538 1.84 1.47 0.00 12.394.62MARINE EQUIPMENT, FLAT-DECK CARGO BARGE, 120' X 30' X 7.25', 400 TON

M10XX006 $245,676 2.59 2.07 0.00 13.376.51MARINE EQUIPMENT, FLAT-DECK CARGO BARGE, 120' X 45' X 7', 800 TON

M10XX007 $312,501 3.30 2.64 0.00 14.298.29MARINE EQUIPMENT, FLAT-DECK CARGO BARGE, 140' X 45' X 7', 900 TON

M10XX008 $433,698 4.58 3.66 0.00 15.9511.50MARINE EQUIPMENT, FLAT-DECK CARGO BARGE, 150' X 45' X 9', 1,100 TON

EP 1110-1-8, Vol. 430 Nov 11

2-155


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

0.48 ALL OTHER BARGES (NON-DREDGING)SUBCATEGORY


OPEN 195M10XX016 $260,800 8.26 2.26 0.00 16.3917.39MARINE EQUIPMENT, ALL OTHER BARGES, HOPPER, 195' X 35' X 12', 1,400 TON

OPEN 200M10XX017 $275,743 8.73 2.39 0.00 16.7618.38MARINE EQUIPMENT, ALL OTHER BARGES, HOPPER, 200' X 35' X 12', 1,600 TON

CLOSED 195M10XX018 $343,442 10.88 2.97 0.00 18.4122.89MARINE EQUIPMENT, ALL OTHER BARGES, HOPPER, 195' X 35' X 12', 1,400 TON (COVERED)

CLOSED 200M10XX019 $350,932 11.11 3.04 0.00 18.6023.39MARINE EQUIPMENT, ALL OTHER BARGES, HOPPER, 200' X 35' X 12', 1,600 TON (COVERED)

0.51 BOATS & LAUNCHES, 0 THRU 250 HPSUBCATEGORY


140COLTM10MZ010 $64,058 3.40 0.62 14.76 952.3224.41MARINE EQUIPMENT, BOATS & LAUNCHES, TRUCKABLE WORKBOAT W/PILOT HOUSE & PUSH KNEES, INBOARD, 20.25' X 8' X 3'

HP D-off

210MUSTANGM10MZ011 $83,016 4.41 0.80 22.13 1903.0135.15MARINE EQUIPMENT, BOATS & LAUNCHES, TRUCKABLE WORKBOAT W/PILOT HOUSE & PUSH KNEES, INBOARD, 25.25' X 10' X 3.5'

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-156


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

SEAARK MARINE

11518' - 72 SERIESM10SM005 $35,460 1.88 0.34 24.49 151.2831.91MARINE EQUIPMENT, BOATS & LAUNCHES, 18' RIVER RUNNER, VEE HULL, NO CABIN, CAP 1,350 LBS, OUTBOARD, 18' X 7.9' X 0.5'

HP G

20019' - UTILITY SERIES

M10SM008 $62,116 3.30 0.60 42.60 172.2555.58MARINE EQUIPMENT, BOATS & LAUNCHES, 19' ROUSTABOUT, TRI HULL, NO CABIN, CAP 2,600 LBS, OUTBOARD, 19.4' X 8.5' X 0.8'

HP G


M10SM001 $78,582 4.17 0.76 31.95 182.8545.27MARINE EQUIPMENT, BOATS & LAUNCHES, 17' LITTLE GIANT, W/CABIN TRI-HULL, CAP 2,000 LBS, OUTBOARD, 17.5' X 7.25' X 0.7'

HP G


M10SM003 $91,559 4.86 0.88 42.60 243.3158.87MARINE EQUIPMENT, BOATS & LAUNCHES, 21' LITTLE GIANT, W/CABIN TRI-HULL, CAP 2,800 LBS, OUTBOARD, 21.4' X 8.5' X 1'

HP G


M10SM004 $96,253 5.11 0.93 53.25 283.4971.55MARINE EQUIPMENT, BOATS & LAUNCHES, 23' LITTLE GIANT, W/CABIN TRI-HULL, CAP 3,400 LBS, OUTBOARD, 23.4' X 8.5' X 1.2'

HP G


7512M10XX010 $52,230 2.77 0.50 7.91 11.8915.09MARINE EQUIPMENT, BOATS & LAUNCHES, 12' TENDER, 7' BEAM, INBOARD ENGINE

HP D-off

5013M10XX009 $15,642 0.83 0.15 10.65 130.5713.90MARINE EQUIPMENT, BOATS & LAUNCHES, 13' RUNABOUT, 5' BEAM, OUTBOARD ENGINE

HP G

10014M10XX011 $60,021 3.19 0.58 10.54 132.1819.04MARINE EQUIPMENT, BOATS & LAUNCHES, 14' TENDER, 7' BEAM, INBOARD ENGINE

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-157


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

M10 NO SPECIFIC MANUFACTURER (continued)100100M10XX012 $61,145 3.25 0.59 10.54 132.2219.17MARINE EQUIPMENT, BOATS &

LAUNCHES, 16', SHALLOW DRAFT, INLAND TUG

HP D-off

115115M10XX013 $79,220 4.21 0.76 12.12 232.8723.03MARINE EQUIPMENT, BOATS & LAUNCHES, 22', SHALLOW DRAFT, INLAND TUG

HP D-off

175175M10XX014 $108,960 5.79 1.05 18.45 603.9533.76MARINE EQUIPMENT, BOATS & LAUNCHES, 18', W/STEERING NOZZLE, INLAND TUG

HP D-off

250250M10XX015 $136,686 7.26 1.32 26.35 834.9546.10MARINE EQUIPMENT, BOATS & LAUNCHES, 26', W/STEERING NOZZLE, INLAND TUG

HP D-off

0.53 BOATS & LAUNCHES, 251 THRU 500 HPSUBCATEGORY


380380M10XX021 $362,510 18.13 3.35 40.05 10012.4286.43MARINE EQUIPMENT, BOATS & LAUNCHES, 40', STANDARD RUDDER, INLAND TUG

HP D-off

435435M10XX022 $412,507 20.63 3.81 45.85 10014.1398.67MARINE EQUIPMENT, BOATS & LAUNCHES, 45' LENGTH, 16' BEAM, 5' 0" DRAFT, PUSH BOAT

HP D-off

400400M10XX023 $552,510 27.63 5.10 42.16 10018.92109.68MARINE EQUIPMENT, BOATS & LAUNCHES, 48' LENGTH, 20' BEAM, 6' 6" DRAFT PUSH BOAT

HP D-off

435435M10XX024 $787,848 39.39 7.28 45.85 13026.98139.73MARINE EQUIPMENT, BOATS & LAUNCHES, 58' LENGTH, 21' BEAM, 6' 0" DRAFT, PUSH BOAT

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-158


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

PILE HAMMER ACCESSORIES - EXTRACTORS & BOX LEADSP100.00 PILE HAMMER ACCESSORIES - EXTRACTORS & BOX LEADSSUBCATEGORY

INTERNATIONAL CONSTRUCTION EQUIPMENT,INC

175216P10IC001 $114,978 12.46 1.36 18.45 1307.5951.71PILE HAMMER ACCESSORIES, PILE EXTRACTOR, 30 TON LINE PULL (ADD LEADS & CRANE)

HP D-off

300416LP10IC002 $180,996 19.61 2.13 31.62 20711.9484.34PILE HAMMER ACCESSORIES, PILE EXTRACTOR, 40 TON LINE PULL (ADD LEADS & CRANE)

HP D-off

8001412BP10IC005 $483,518 52.38 5.70 84.32 59331.89225.13PILE HAMMER ACCESSORIES, PILE EXTRACTOR, 150 TON LINE PULL (ADD LEADS & CRANE)

HP D-off

P10IC010 $16,953 1.84 0.20 0.00 1011.124.52PILE HAMMER ACCESSORIES, PILE LEADS, SWING, 26" X 86'

P10IC012 $23,911 2.59 0.28 0.00 1551.586.37PILE HAMMER ACCESSORIES, PILE LEADS, SWING, 32" X 88'

13P10IC011 $33,431 3.62 0.39 1.37 1342.2010.47PILE HAMMER ACCESSORIES, PILE LEADS, FIXED, 26" X 86', W/SPOTTER

HP D-off

13P10IC013 $41,465 4.49 0.49 2.77 1932.7414.21PILE HAMMER ACCESSORIES, PILE LEADS, FIXED, 32" X 88', W/SPOTTER

HP G

EP 1110-1-8, Vol. 430 Nov 11

2-159


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

PILE HAMMERS, DOUBLE ACTINGP200.10 DIESELSUBCATEGORY


422P20IC002 $104,377 13.05 1.17 0.00 1227.7037.13PILE HAMMER, DOUBLE ACTING, DIESEL, 22,500 FT-LBS, MAX STROKE 5' 8" (ADD LEADS & CRANE)



0.20 PNEUMATIC (STEAM/AIR)SUBCATEGORY

MKT MANUFACTURING, INC.

2505P20MK002 $26,329 3.51 0.29 0.00 172.059.60PILE HAMMER, DOUBLE ACTING, PNUEMATIC (STEAM/AIR), 1,000 FT-LBS, MAX STROKE 7" (ADD 250 CFM COMPRESSOR, LEADS & CRANE)

CFM A

4006P20MK003 $29,689 3.96 0.32 0.00 312.3011.26PILE HAMMER, DOUBLE ACTING, PNUEMATIC (STEAM/AIR), 2,500 FT-LBS, MAX STROKE 8.75" (ADD 400 CFM COMPRESSOR, LEADS & CRANE)

CFM A

4507P20MK004 $41,672 5.56 0.45 0.00 513.2315.65PILE HAMMER, DOUBLE ACTING, PNUEMATIC (STEAM/AIR), 4,150 FT-LBS, MAX STROKE 9.5" (ADD 450 CFM COMPRESSOR, LEADS & CRANE)

CFM A

EP 1110-1-8, Vol. 430 Nov 11

2-160


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

P20 MKT MANUFACTURING, INC. (continued)6009B3P20MK005 $64,249 8.57 0.70 0.00 724.9923.46PILE HAMMER, DOUBLE ACTING,

PNUEMATIC (STEAM/AIR), 8,750 FT-LBS, MAX STROKE 17" (ADD 600 CFM COMPRESSOR, LEADS & CRANE)

CFM A

75010B3P20MK006 $87,338 11.65 0.95 0.00 1116.7832.68PILE HAMMER, DOUBLE ACTING, PNUEMATIC (STEAM/AIR), 13,100 FT-LBS, MAX STROKE 19" (ADD 750 CFM COMPRESSOR, LEADS & CRANE)

CFM A

90011B3P20MK007 $98,951 13.19 1.07 0.00 1397.6736.68PILE HAMMER, DOUBLE ACTING, PNUEMATIC (STEAM/AIR), 19,150 FT-LBS, MAX STROKE 19" (ADD 900 CFM COMPRESSOR, LEADS & CRANE)

CFM A

PILE HAMMERS, SINGLE ACTINGP250.10 DIESELSUBCATEGORY

PILECO, INC.

21D6-42P25DL001 $25,621 3.42 0.28 2.21 361.9911.86PILE HAMMER, SINGLE ACTING, DIESEL, 10,500 FT-LBS (ADD LEADS & CRANE)

HP D-off


HP D-off


HP D-off


HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-161


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

P25 PILECO, INC. (continued)119D30-32P25DL006 $61,382 8.18 0.67 12.54 1354.7637.69PILE HAMMER, SINGLE ACTING, DIESEL,

69,898 FT-LBS (ADD LEADS & CRANE)

HP D-off


HP D-off


HP D-off


HP D-off


HP D-off


30SP25IC001 $71,425 9.52 0.78 0.00 735.5425.57PILE HAMMER, SINGLE ACTING, DIESEL, 22,500 FT-LBS (ADD LEADS & CRANE)




EP 1110-1-8, Vol. 430 Nov 11

2-162


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

P25 INTERNATIONAL CONSTRUCTION EQUIPMENT,INC (continued)




DE-33/30/20CP25MK001 $61,014 8.14 0.66 0.00 784.7322.47PILE HAMMER, SINGLE ACTING, DIESEL, 33,000 FT-LBS (ADD LEADS & CRANE)

DE-70/50CP25MK003 $94,683 12.62 1.03 0.00 1537.3435.13PILE HAMMER, SINGLE ACTING, DIESEL, 70,000 FT-LBS (ADD LEADS & CRANE)

0.20 PNEUMATIC (STEAM/AIR)SUBCATEGORY

VULCAN FOUNDATION EQUIPMENT, INC

750306P25VU002 $74,503 10.55 0.79 0.00 1216.0727.47PILE HAMMER, SINGLE ACTING, PNUEMATIC (STEAM/AIR), 18,000 FT-LBS (ADD 750 CFM COMPRESSOR, LEADS & CRANE)

CFM A


CFM A


CFM A

EP 1110-1-8, Vol. 430 Nov 11

2-163


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

P25 VULCAN FOUNDATION EQUIPMENT, INC (continued)


CFM A

1,050510P25VU010 $129,390 18.33 1.36 0.00 22210.5344.32PILE HAMMER, SINGLE ACTING, PNUEMATIC (STEAM/AIR), 50,000 FT-LBS (ADD 1,050 CFM COMPRESSOR, LEADS & CRANE)

CFM A

1,200512P25VU011 $131,052 18.57 1.38 0.00 24210.6745.10PILE HAMMER, SINGLE ACTING, PNUEMATIC (STEAM/AIR), 60,000 FT-LBS (ADD 1,200 CFM COMPRESSOR, LEADS & CRANE)

CFM A

PILE HAMMERS, DRIVER/ EXTRACTOR, VIBRATORYP300.00 PILE HAMMERS, DRIVER/ EXTRACTOR, VIBRATORYSUBCATEGORY


185V-5C/HP-185P30MK001 $101,928 13.59 1.11 19.50 1207.9155.60PILE HAMMER, DRIVER/EXTRACTOR, VIBRATORY, 53 TON FORCE DRIVE (ADD LEADS & CRANE)

HP D-off

325V-20B/HP-365P30MK003 $173,110 23.08 1.88 34.26 22013.4295.73PILE HAMMER, DRIVER/EXTRACTOR, VIBRATORY, 98.5 TON FORCE DRIVE (ADD LEADS & CRANE)

HP D-off

630V-35/HP-630P30MK004 $295,383 39.38 3.21 66.40 32722.90172.41PILE HAMMER, DRIVER/EXTRACTOR, VIBRATORY, 200 TON FORCE DRIVE (ADD LEADS & CRANE)

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-164


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

PIPELAYERSP350.00 PIPELAYERSSUBCATEGORY


110561MP35CA001 $230,457 13.17 2.33 6.36 3588.9240.03PIPELAYER, 18' BOOM, 40,000 LBS CAPACITY

HP D-off

230572-RP35CA008 $426,979 24.40 4.31 13.29 66916.5175.95PIPELAYER, 20' BOOM, 90,000 LBS CAPACITY

HP D-off

305583-RP35CA009 $550,089 31.43 5.55 17.63 98421.2798.44PIPELAYER, 20' BOOM, 140,000 LBS CAPACITY

HP D-off

420589P35CA006 $713,684 40.78 7.20 24.28 1,45027.59129.36PIPELAYER, 28' BOOM, 230,000 LBS CAPACITY

HP D-off

PLATFORMS & MAN-LIFTSP400.00 PLATFORMS & MAN-LIFTSSUBCATEGORY

BIL-JAX, INC.

SKYRIDER 15P40BX001 $13,460 1.51 0.13 0.00 180.893.15MAN-LIFT, TELESCOPIC MAST, 14.8' HEIGHT, 500 LBS, 24 VOLT DC, RECHARGABLE BATTERIES, SELF PROPELLED, 2.2' X 4' PLATFORM

TEREX CORPORATION

32TA50RTP40TE003 $91,189 9.92 0.90 2.61 1545.8625.14MAN-LIFT, ARTICULATED BOOM, 55' HEIGHT, 500 LBS, 29' REACH, 4X4, SELF PROPELLED, 2.2' X 5' PLATFORM

HP D-off

44TA60RTP40TE004 $104,910 11.55 1.03 3.59 2416.8129.13MAN-LIFT, ARTICULATED BOOM, 66' HEIGHT, 500 LBS, 33' REACH, 4X4, SELF PROPELLED, 3' X 6' PLATFROM

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-165


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

P40 TEREX CORPORATION (continued)66TB42P40TE005 $80,281 8.70 0.79 5.39 1315.1425.76MAN-LIFT, STRAIGHT BOOM, 43' HEIGHT,

650 LBS, 37' REACH, 4X4, SELF PROPELLED, 3' X 6' PLATFORM

HP D-off

66TB66P40TE006 $107,547 11.76 1.06 5.39 2506.9432.06MAN-LIFT, STRAIGHT BOOM, 66' HEIGHT, 650 LBS, 51' REACH, 4X4, SELF PROPELLED, 3' X 6' PLATFORM

HP D-off


HP D-off


HP D-off


HP D-off

210T-292P40TE010 $76,373 8.42 0.75 17.14 1154.9637.34MAN-LIFT, LINE-TRUCK, W/AERIAL 2' X 2.5' PLATFORM, 300 LBS, 34' HEIGHT, 23' RAD

HP D-off

210T-38PP40TE011 $84,146 9.19 0.83 17.14 1285.4339.43MAN-LIFT, LINE-TRUCK, W/AERIAL 2' X 2.5' PLATFORM, 300 LBS, 43' HEIGHT, 26' RAD

HP D-off

210Digger DerrickC-4045

P40TE012 $126,082 13.90 1.24 17.14 2688.1949.10MAN-LIFT, LINE-TRUCK, W/13.7 TON, 45' HIGH-BOOM TILT POLE CLAWS, & 1.5' DIA AUGER

HP D-off

2105FC-52P40TE013 $115,386 12.70 1.14 17.14 2157.4946.64MAN-LIFT, LINE-TRUCK, W/AERIAL 2' X 4' PLATFORM, 700 LBS, 57' HEIGHT, 35' RAD

HP D-off

2105FC-55P40TE014 $117,635 12.95 1.16 17.14 2487.6447.15MAN-LIFT, LINE-TRUCK, W/AERIAL 2' X 2.5' PLATFORM, 500 LBS, 60' HEIGHT, 38' RAD

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-166


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

P40 TEREX CORPORATION (continued)2106H-65P40TE015 $133,457 14.73 1.32 17.14 2558.6950.81MAN-LIFT, LINE-TRUCK, W/AERIAL 2' X 4'

PLATFORM, 750 LBS, 70' HEIGHT, 39' RAD

HP D-off

PUMPS, GROUTP450.00 PUMPS, GROUTSUBCATEGORY

AIRPLACO EQUIPMENT CO., INC.

HG-5P45AF002 $938 0.10 0.01 0.00 10.060.24PUMP, GROUT, HAND PUMP, 12 CF/HR, 0-100 PSI, W/O HOPPER (ADD HOSES)

HG-9P45AF003 $1,353 0.14 0.01 0.00 10.080.34PUMP, GROUT, HAND PUMP, 15 CF/HR, 0-100 PSI, W/5 GAL HOPPER (ADD HOSES)

5HGA-530P45AF008 $8,156 0.87 0.08 0.00 40.522.17PUMP, GROUT, 50 CF/HR, 0-250 PSI, SKID MTD, W/5 GAL HOPPER AND 30 GAL MIXER (ADD 50 CFM COMPRESSOR & HOSE)

CFM A

10SM-78MDP45AF009 $18,231 1.94 0.19 1.53 131.166.45PUMP, GROUT, 0 - 10 GAL/MIN, TRL MTD, W/60 GAL HOPPER, 4.5 CF HYDRAULIC MIXERS, & 12 CFM COMPRESSOR (ADD HOSE)

HP D-off

12MJ-16P45AF006 $11,279 1.12 0.11 3.73 70.677.15PUMP, MUDJACK/ SLABJACKING, 160 CF/HR, 0-400 PSI, GROUT-MUD JACKING-SHOTCRETE, TRAILER MTD, W/5 CF HOPPER (ADD 2" HOSE)

HP G

46Pro-CretorP45AF010 $61,407 6.48 0.63 7.04 373.8723.49PUMP, GROUT/SHOTCRETE, SELF CONTAINED W/ 10 CF MIXER, HIGH PRESSURE DUAL CYLINDER PUMP, S-TUBE, TRAILER MTD (ADD HOSE)

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-167


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

P45 AIRPLACO EQUIPMENT CO., INC. (continued)

60COBRA 536P45AF011 $55,292 5.83 0.56 9.18 493.4824.34PUMP, GROUT/SHOTCRETE, HIGH PRESSURE DUAL CYLINDER GROUT PUMP, 30-36 CY/HR, 0 - 900 PSI, GROUT-MUD JACK-SHOTCRETE, TRAILER MTD, (ADD UP TO 5" HOSE)

HP D-off

25PG-25 PumpMaster

P45AF007 $14,298 1.46 0.15 7.76 250.8812.50PUMP, GROUT, HIGH VOLUME DUAL CYLINDER GROUT PUMP, 756 CF/HR CONCRETE, 350 CF/HR SHOTCRETE, TRAILER MTD, W/5 CF HOPPER (ADD HOSE 1" - 2" DIA)

HP G

ALLENTOWN EQUIPMENT

46POWER CRETER MAGNUM

P45AL015 $63,343 6.69 0.65 7.04 354.0023.99PUMP, GROUT, GROUT-MUD JACK-SHOTCRE, HIGH PRESSURE DUAL CYLINDER GROUT PUMP, 135 CF/HR, 0 - 1,770 PSI, TRAILER MTD, W/75 GAL HOPPER/ 82 GAL MIXER/ 3" HOSE

HP D-off

CHEMGROUT, INC.

15CG-050P45CG001 $4,172 0.44 0.04 0.00 10.261.10PUMP, GROUT, MINI, AIR, 40 CF/HR, 225 PSI, PORTABLE, SKID MTD (ADD 15 CFM - 100 PSI COMPRESSOR)

CFM A

85CG-550PP45CG002 $6,816 0.72 0.07 0.00 30.431.83PUMP, GROUT, MIXER, AIR, 40 CF/HR, 225 PSI, SKID MTD (ADD 85 CFM - 100 PSI COMPRESSOR)

CFM A

230CG-500/2C6 VERSATILE

P45CG003 $15,556 1.65 0.16 0.00 120.994.10PUMP, GROUT, MIXER, AIR, 160 CF/HR, 160 PSI, SKID MTD, 15 GAL HOPPER & 2 - 70 GAL MIXING TANKS (ADD 250 CFM - 100 PSI COMPRESSOR)

CFM A

EP 1110-1-8, Vol. 430 Nov 11

2-168


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

P45 CHEMGROUT, INC. (continued)16CG-570 / 3C6 / HP45CG007 $23,212 2.47 0.24 4.97 131.4811.57PUMP, GROUT, THICK MIX/SPRAY, 64

CF/HR, 261 PSI, SKID MTD, 15 GAL HOPPER & 45 GAL MIXING TANK, W/AIR COMPRESSOR, POWER UNIT

HP G

16CG-570 / 3C6P45CG006 $28,922 3.03 0.29 4.97 151.8113.01PUMP, GROUT, THICK MIX/SPRAY, 64 CF/HR, 261 PSI, TRAILER MTD, 15 GAL HOPPER & 45 GAL MIXING TANK, W/AIR COMPRESSOR, POWER UNIT

HP G

OLIN ENGINEERING, INC.

555 40P45OE002 $36,457 3.84 0.37 8.42 422.2918.72PUMP, GROUT PUMP, 1,134 CF/HR, 750 PSI, 37 GAL HOPPER, TRAILER MTD, W/POWER UNIT

HP D-off


HP D-off


HP D-off

1815 140CAP45OE005 $76,268 8.03 0.78 27.69 1004.8050.47PUMP, GROUT PUMP, 3,780 CF/HR, 900 PSI, 37 GAL HOPPER, TRAILER MTD TANDEM, W/POWER UNIT

HP D-off

PUMPS, WATER, CENTRIFUGAL, TRASHP500.11 ENGINE DRIVESUBCATEGORY

WACKER CORPORATION

10PT 2AP50WC001 $1,438 0.14 0.02 2.92 10.093.67PUMP, WATER, CENTRIFUGAL, TRASH, ENGINE DRIVE, 2" DIA, 205 GPM @ 100' HEAD (ADD HOSES)

HP G

EP 1110-1-8, Vol. 430 Nov 11

2-169


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

P50 WACKER CORPORATION (continued)15PT 3AP50WC002 $1,693 0.17 0.02 2.19 20.112.96PUMP, WATER, CENTRIFUGAL, TRASH,

ENGINE DRIVE, 3" DIA, 425 GPM @ 95' HEAD (ADD HOSES)

HP D-off

16PTS 4VP50WC003 $3,939 0.39 0.04 2.34 30.243.65PUMP, WATER, CENTRIFUGAL, TRASH, ENGINE DRIVE, 4" DIA, 705 GPM @ 106' HEAD (ADD HOSES)

HP D-off

33PT 6LTP50WC004 $18,222 1.80 0.19 4.82 251.099.90PUMP, WATER, CENTRIFUGAL, TRASH, ENGINE DRIVE, 6" DIA, 1,300 GPM @ 100' HEAD ,TRAILER MTD (ADD HOSES)

HP D-off


606'' DIESELP50XX001 $25,390 2.54 0.27 8.77 221.5416.19PUMP, WATER, CENTRIFUGAL, TRASH, ENGINE DRIVE, 6" DIA, 1,165 GPM, AIR COOLED (ADD HOSES)

HP D-off

708'' DIESELP50XX002 $46,895 4.69 0.49 10.23 352.8422.92PUMP, WATER, CENTRIFUGAL, TRASH, ENGINE DRIVE, 8" DIA, 2,085 GPM, WATER COOLED (ADD HOSES)

HP D-off

8510'' DIESELP50XX003 $50,296 5.03 0.53 12.43 433.0526.28PUMP, WATER, CENTRIFUGAL, TRASH, ENGINE DRIVE, 10" DIA, 2,665 GPM, WATER COOLED (ADD HOSES)

HP D-off

0.31 HOSES, PUMP, SUCTION & DISCHARGESUBCATEGORY

GORMAN-RUPP COMPANY

C221-90P50GR001 $120 0.03 0.00 0.00 10.020.08PUMP, WATER, CENTRIFUGAL, TRASH, HOSE, SUCTION, 2" DIA X 20' WITH COUPLING (PER SECTION)


EP 1110-1-8, Vol. 430 Nov 11

2-170


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

P50 GORMAN-RUPP COMPANY (continued)C357-90P50GR003 $320 0.07 0.00 0.00 10.040.20PUMP, WATER, CENTRIFUGAL, TRASH,

HOSE, SUCTION, 4" DIA X 20' WITH COUPLING (PER SECTION)


C373-90P50GR005 $106 0.02 0.00 0.00 10.010.06PUMP, WATER, CENTRIFUGAL, TRASH, HOSE, DISCH, 2" DIA X 50' WITH COUPLING (PER SECTION)




PUMPS, WATER, SUBMERSIBLEP550.01 ENGINE DRIVESUBCATEGORY

GRIFFIN DEWATERING CORP.

214MHP55GF001 $21,005 2.10 0.22 3.07 191.278.78PUMP, WATER, SUBMERSIBLE, ENGINE DRIVE, 4" DIA, 400 GPM @ 20' HEAD, SKID MTD (INCLUDES POWER UNIT MODEL 250)(ADD HOSES)

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-171


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

P55 GRIFFIN DEWATERING CORP. (continued)726TP55GF002 $30,113 3.01 0.32 10.53 311.8319.76PUMP, WATER, SUBMERSIBLE, ENGINE

DRIVE, 6" DIA, 2,000 GPM @ 20' HEAD, SKID MTD (INCLUDES POWER UNIT MODEL 400)(ADD HOSES)

HP D-off

0.02 ELECTRIC DRIVESUBCATEGORY

GORMAN-RUPP COMPANY

2S2A1P55GR001 $4,119 0.44 0.04 0.15 20.261.04PUMP, WATER, SUBMERSIBLE, ELECTRIC, 2" DIA, 138 GPM @ 20' HEAD (ADD HOSES)

HP E


HP E


HP E

60S6A1P55GR004 $19,802 2.10 0.20 4.37 141.2510.47PUMP, WATER, SUBMERSIBLE, ELECTRIC, 6" DIA, 1,950 GPM @ 40' HEAD (ADD HOSES)

HP E

WACKER CORPORATION

1PS2 500P55WC001 $420 0.04 0.00 0.07 10.020.17PUMP, WATER, SUBMERSIBLE, ELECTRIC, 2" DIA, 66 GPM @ 39' HEAD (ADD HOSES)

HP E

1PS2 750P55WC002 $572 0.06 0.01 0.07 10.040.22PUMP, WATER, SUBMERSIBLE, ELECTRIC, 2" DIA, 100 GPM @ 52' HEAD (ADD HOSES)

HP E

EP 1110-1-8, Vol. 430 Nov 11

2-172


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

PUMPS, WATER, CENTRIFUGAL, DEWATERINGP600.11 SKID MOUNTED, ENGINE DRIVESUBCATEGORY

RIVERSIDE PUMP MANUFACTURING

4S2BP60HO002 $972 0.10 0.01 1.02 10.061.39PUMP, WATER, CENTRIFUGAL, DEWATERING, SKID MOUNTED, ENGINE DRIVE, 2" DIA, 150 GPM @ 22' HEAD (ADD HOSES)

HP G

8TP3BP60HO003 $1,736 0.17 0.02 2.34 10.113.07PUMP, WATER, CENTRIFUGAL, DEWATERING, SKID MOUNTED, ENGINE DRIVE, 3" DIA, 293 GPM @ 20' HEAD (ADD HOSES)

HP G

WACKER CORPORATION

4PG 2AP60WC001 $717 0.07 0.01 1.17 10.051.51PUMP, WATER, CENTRIFUGAL, DEWATERING, SKID MOUNTED, ENGINE DRIVE, 2" DIA, 159 GPM @ 98' HEAD (ADD HOSES)

HP G

6PG 3AP60WC002 $946 0.09 0.01 1.75 10.062.22PUMP, WATER, CENTRIFUGAL, DEWATERING, SKID MOUNTED, ENGINE DRIVE, 3" DIA, 264 GPM @ 98' HEAD (ADD HOSES)

HP G

0.21 WHEEL MOUNTED, ENGINE DRIVESUBCATEGORY

GRIFFIN DEWATERING CORP.

21250/4"MHP60GF003 $24,571 2.42 0.26 3.07 191.479.35PUMP, WATER, CENTRIFUGAL, DEWATERING, WHEEL, 4" DIA, 400 GPM @ 60' HEAD (ADD HOSES)

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-173


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

P60 GRIFFIN DEWATERING CORP. (continued)72400/6"TP60GF008 $33,678 3.33 0.35 10.53 312.0220.19PUMP, WATER, CENTRIFUGAL,

DEWATERING, 6" DIA, 1,040 GPM @ 60' HEAD, SKID MTD. (ADD HOSES)

HP D-off

72400/6"TP60GF004 $29,599 2.92 0.31 10.53 311.7719.24PUMP, WATER, CENTRIFUGAL, DEWATERING, WHEEL, 6" DIA, 2,000 GPM @ 60' HEAD (ADD HOSES)

HP D-off


HP D-off


HP D-off

GORMAN-RUPP COMPANY

4714C2-F3LP60GR001 $25,479 2.51 0.27 6.87 201.5313.99PUMP, WATER, CENTRIFUGAL, DEWATERING, WHEEL, 4" DIA, 600 GPM @ 80' HEAD (ADD HOSES)

HP D-off

10116C2-F4LP60GR002 $29,716 2.94 0.31 29.53 201.7840.66PUMP, WATER, CENTRIFUGAL, DEWATERING, WHEEL, 6" DIA, 1,825 GPM @ 40' HEAD (ADD HOSES)

HP G

PUMPS, WATER, DIAPHRAGMP650.11 SKID MOUNTED, ENGINE DRIVESUBCATEGORY

RIVERSIDE PUMP MANUFACTURING

4DP2BP65HO001 $1,746 0.17 0.02 1.02 10.111.57PUMP, WATER, DIAPHRAGM, SKID MTD, 2" DIA, 33 GPM @ 25' HEAD (ADD HOSES)

HP G

EP 1110-1-8, Vol. 430 Nov 11

2-174


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

P65 RIVERSIDE PUMP MANUFACTURING (continued)

4DP3BP65HO002 $2,028 0.20 0.02 1.02 20.121.63PUMP, WATER, DIAPHRAGM, SKID MTD, 3" DIA, 80 GPM @ 25' HEAD (ADD HOSES)

HP G

0.21 WHEEL MOUNTED, ENGINE DRIVESUBCATEGORY

GORMAN-RUPP COMPANY

53D-13P65GR001 $4,545 0.38 0.05 1.46 20.242.71PUMP, WATER, DIAPHRAGM, WHEEL, 2" DIA SUCTION X 3" DIA DISCHARGE, 56 GPMH @ 25' HEAD (ADD HOSES)

HP G

23D-BP65GR002 $5,349 0.46 0.06 0.44 20.291.72PUMP, WATER, DIAPHRAGM, WHEEL, 3" DIA, 560 GPM @ 25' HEAD (ADD HOSES)

HP G

34D-BP65GR003 $12,827 1.20 0.13 0.88 30.733.87PUMP, WATER, DIAPHRAGM, WHEEL, 4" DIA, 74 GPM @ 25' HEAD (ADD HOSES)

HP G

WACKER CORPORATION

4PDT 2AP65WC001 $1,856 0.19 0.02 1.17 10.121.75PUMP, WATER, DIAPHRAGM, WHEEL, 2" DIA, 50 GPM @ 25' HEAD (ADD HOSES)

HP G

4PDT 3AP65WC002 $2,006 0.20 0.02 1.17 20.121.78PUMP, WATER, DIAPHRAGM, WHEEL, 3" DIA, 88 GPM @ 25' HEAD (ADD HOSES)

HP G

EP 1110-1-8, Vol. 430 Nov 11

2-175


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

PUMPS, WATER (For core drills)P700.01 ENGINE DRIVESUBCATEGORY


275-7.6P70XX001 $3,560 0.33 0.04 0.58 10.211.42PUMP, WATER, FOR CORE DRILLS, 7.6 GPM, 75 PSI, MANUAL, SKID (ADD HOSES)

HP G

6225-17.5P70XX002 $9,285 0.87 0.10 1.75 10.543.99PUMP, WATER, FOR CORE DRILLS, 17.5 GPM, 225 PSI, MANUAL, SKID (ADD HOSES)

HP G

RIPPERS & HYDRAULIC BANK SLOPERS (Add cost for point wear)R100.00 RIPPERS & HYDRAULIC BANK SLOPERS (Add cost for point wear)SUBCATEGORY


D-5C111R10CA006 $288 0.03 0.00 0.00 10.020.07RIPPER, SHANK, EACH (ADD D-5 TRACTOR DOZER & RIPPER & COST FOR POINT WEAR)

D6RII-174-9198R10CA022 $1,155 0.12 0.01 0.00 20.070.27RIPPER SHANK, EACH (ADD D6RII TRACTOR DOZER & RIPPER & COST FOR POINT WEAR)

D6R II - 9J-8926R10CA023 $1,165 0.12 0.01 0.00 20.070.27RIPPER, SHANK, EACH (ADD D-6 TRACTOR DOZER & RIPPER & COST FOR POINT WEAR)

D-7RR10CA010 $1,891 0.19 0.02 0.00 20.120.44RIPPER, SHANK, EACH (ADD D-7 TRACTOR DOZER & RIPPER & COST FOR POINT WEAR)

EP 1110-1-8, Vol. 430 Nov 11

2-176


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

R10 CATERPILLAR INC. ( MACHINE DIVISION) (continued)




D-3R10CA001 $10,975 1.10 0.12 0.00 130.672.65RIPPER, 3-SHANKS & BEAM, HYDRAULIC (ADD D-3 TRACTOR DOZER & COST FOR POINT WEAR)

D-4C SERIES IIIR10CA003 $10,975 1.10 0.12 0.00 130.672.65RIPPER, 3-SHANKS & BEAM, HYDRAULIC (ADD D-4 TRACTOR DOZER & COST FOR POINT WEAR)

D-5C SERIES IIIR10CA005 $10,975 1.10 0.12 0.00 130.672.65RIPPER, 3-SHANKS & BEAM, HYDRAULIC (ADD D-5 TRACTOR DOZER & COST FOR POINT WEAR)

D-6R IIR10CA007 $25,201 2.52 0.27 0.00 401.535.96RIPPER, 3-SHANKS & BEAM, HYDRAULIC (ADD D-6 TRACTOR DOZER & COST FOR POINT WEAR)

D-7RR10CA009 $46,925 4.69 0.49 0.00 772.8411.02RIPPER, 3-SHANKS & BEAM, HYDRAULIC (ADD D-7 TRACTOR DOZER & COST FOR POINT WEAR)

D-8RR10CA011 $50,996 5.10 0.54 0.00 913.0912.00RIPPER, 1-SHANK & BEAM, HYDRAULIC (ADD D-8 TRACTOR DOZER & RIPPER & COST FOR POINT WEAR)

EP 1110-1-8, Vol. 430 Nov 11

2-177


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)



D-9RR10CA014 $65,601 6.56 0.69 0.00 1023.9715.46RIPPER, 1-SHANK & BEAM, HYDRAULIC (ADD D-9 TRACTOR DOZER & COST FOR POINT WEAR)






ROLLERS, STATIC, TOWED, PNEUMATICR150.00 ROLLERS, STATIC, TOWED, PNEUMATICSUBCATEGORY

SOUTHWEST CONSTRUCTION EQUIPMENT CO.

C-50R15SO001 $146,732 10.44 1.51 0.00 3096.7324.55ROLLER, STATIC, TOWED, PNEUMATIC, 60 TON, 9.8' WIDE, 4 TIRE (ADD TOWING UNIT)

EP 1110-1-8, Vol. 430 Nov 11

2-178


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

R15 SOUTHWEST CONSTRUCTION EQUIPMENT CO. (continued)

C-75R15SO002 $161,813 9.94 1.67 0.00 3476.6426.67ROLLER, STATIC, TOWED, PNEUMATIC, 75 TON, 10.5' WIDE, 4 TIRE (ADD TOWING UNIT)

C-100XLR15SO003 $225,811 15.06 2.33 0.00 5519.8637.57ROLLER, STATIC, TOWED, PNEUMATIC, 100 TON, 10.5' WIDE, 4 TIRE (ADD TOWING UNIT)

ROLLERS, STATIC, TOWED, STEEL DRUMR200.00 ROLLERS, STATIC, TOWED, STEEL DRUMSUBCATEGORY

REYNOLDS INTERNATIONAL, L.P.

DD-48X60R20RI002 $36,655 2.93 0.38 0.00 1771.856.77ROLLER, STATIC, TOWED, 2 STEEL DRUMS, 10-15 TON, 48" WIDE X 60" DIA, PADFOOT (ADD TOWING UNIT)


2DH-RRR20SO001 $81,285 6.50 0.84 0.00 2004.0914.72ROLLER, STATIC, TOWED, 2 STEEL DRUMS, 10-20 TON, 60" WIDE X 60" DIA, SHEEPSFOOT (ADD TOWING UNIT)

ROLLERS, STATIC, SELF-PROPELLED R300.01 PNEUMATICSUBCATEGORY


85BW11RHR30BO004 $75,978 7.30 0.77 10.98 1004.4229.03ROLLER, STATIC, SELF-PROPELLED, PNEUMATIC, 13.50 TON, 68" WIDE, 9 TIRE, ASPHALT COMPACTOR

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-179


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

R30 COMPACTION AMERICA (BOMAG) (continued)

110BW24RR30BO003 $143,193 14.29 1.46 14.21 2908.6146.97ROLLER, STATIC, SELF-PROPELLED, PNEUMATIC, 30.00 TON, 78" WIDE, 8 TIRE, ASPHALT COMPACTOR

HP D-off


70PS-150BR30CA010 $82,228 8.56 0.84 9.04 855.1227.72ROLLER, STATIC, SELF-PROPELLED, PNEUMATIC, 14.25 TON, 68" WIDE, 9 TIRE, ASPHALT COMPACTOR

HP D-off


HP D-off


HP D-off


80TRU-PAC 915R30RS003 $70,938 7.21 0.72 10.34 1154.3326.78ROLLER, STATIC, SELF-PROPELLED, PNEUMATIC, 6-15 TON, 68" WIDE, 9 TIRES, ASPHALT/SOIL COMPACTOR

HP D-off

SAKAI AMERICA, INC.

91TS200R30SI002 $118,461 11.98 1.21 11.76 1877.2038.76ROLLER, STATIC, SELF-PROPELLED, PNEUMATIC, 16 TON, 81" WIDE, 9 TIRE, ASPHALT COMPACTOR

HP D-off

95TS600CR30SI003 $147,019 15.01 1.50 12.27 1879.0145.39ROLLER, STATIC, SELF-PROPELLED, PNEUMATIC, 16 TON, 81" WIDE, 9 TIRE, ASPHALT COMPACTOR

HP D-off

108TS650CR30SI004 $194,921 20.17 1.99 13.95 28112.0857.35ROLLER, STATIC, SELF-PROPELLED, PNEUMATIC, 27 TON, 82" WIDE, 7 TIRE, ASPHALT COMPACTOR

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-180


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

0.02 SMOOTH DRUMSUBCATEGORY


47BW5ASR30BO005 $82,586 7.02 0.82 6.07 1304.3321.79ROLLER, STATIC, SELF-PROPELLED, SMOOTH DRUM, DOUBLE DRUM, 6 TON, 40" WIDE ASPHALT COMPACTOR

HP D-off


HP D-off


HP D-off


16300 BR30RS001 $15,977 1.36 0.16 4.16 260.847.52ROLLER, STATIC, SELF-PROPELLED, SMOOTH DRUM, DOUBLE DRUM, 1.5 TON, 34" WIDE, ASPHALT COMPACTOR

HP G

40400R30RS002 $31,927 2.71 0.32 5.17 371.6811.55ROLLER, STATIC, SELF-PROPELLED, SMOOTH DRUM, DOUBLE DRUM, 2 TON, 40" WIDE, ASPHALT COMPACTOR

HP D-off

SAKAI AMERICA, INC.

75R2H-2R30SI005 $126,786 10.78 1.27 9.69 2076.6633.88ROLLER, STATIC, SELF-PROPELLED, SMOOTH DRUM, 3 DRUMS, 14 TON, 64" WIDE, ASPHALT COMPACTOR

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-181


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

0.03 TAMPING FOOT, LANDFILL & SOIL COMPACTORSSUBCATEGORY


442BC672RBR30BO009 $532,269 35.48 5.42 57.11 71023.16142.94ROLLER, STATIC, SELF-PROPELLED, LANDFILL/SOIL COMPACTOR, SHEEPSFOOT, 4X4, 35 TON, 63" DIA, 19.58' WIDTH PER 2-PASS, W/BLADE

HP D-off

442BC772RBR30BO008 $543,609 36.24 5.54 57.11 81223.66144.65ROLLER, STATIC, SELF-PROPELLED, LANDFILL/SOIL COMPACTOR, SHEEPSFOOT, 4X4, 40 TON, 63" DIA, 19.58' WIDTH PER 2-PASS, W/BLADE

HP D-off


240815-FR30CA003 $397,714 26.51 4.05 31.01 44917.3193.92ROLLER, STATIC, SELF-PROPELLED, LANDFILL/SOIL COMPACTOR, SHEEPSFOOT, 4X4, 23 TON, 56" DIA, 14.25' WIDTH PER 2-PASS, W/BLADE

HP D-off

220816-FR30CA012 $405,469 27.03 4.13 28.42 50917.6592.21ROLLER, STATIC, SELF-PROPELLED, LANDFILL/SOIL COMPACTOR, TAMPING FOOT, CHOPPER, 4X4, 25.0 TON, 14.75' WIDTH PER 2-PASS, W/BLADE

HP D-off

315825-G IIR30CA006 $602,727 40.18 6.14 40.70 73426.23135.37ROLLER, STATIC, SELF-PROPELLED, LANDFILL/SOIL COMPACTOR, SHEEPSFOOT, 4X4, 35 TON, 51" DIA, 16.00' WIDTH PER 2-PASS, W/BLADE

HP D-off

315826-G IIR30CA013 $627,249 41.82 6.39 40.70 77127.30139.05ROLLER, STATIC, SELF-PROPELLED, LANDFILL/SOIL COMPACTOR, TAMPING FOOT, CHOPPER, 4X4, 36.5 TON, 15.66' WIDTH PER 2-PASS, W/BLADE

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-182


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT


473836 GR30CA009 $829,148 55.28 8.45 61.11 1,16636.09191.90ROLLER, STATIC, SELF-PROPELLED, LANDFILL/SOIL COMPACTOR, TAMPING FOOT, CHOPPER, 4X4, 50.0 TON, 18.58' WIDTH PER 2-PASS, W/BLADE

HP D-off

ROLLERS, VIBRATORY, TOWEDR400.00 ROLLERS, VIBRATORY, TOWEDSUBCATEGORY


50BW6R40BO001 $66,410 6.64 0.70 7.31 1284.0222.96ROLLER, VIBRATORY, TOWED, SINGLE DRUM, SMOOTH, 13,000 LB OPER. WT., 26,550 LB (13.3 TONS) CENTRIFUGAL FORCE, 67'' WIDE (ADD 180 HP TOWING UNIT)

HP D-off

50BW6SR40BO002 $71,974 7.20 0.76 7.31 1484.3624.19ROLLER, VIBRATORY, TOWED, SINGLE DRUM, SHEEPSFOOT, 15,000 LB OPER. WT., 26,550 LB (13.3 TONS) CENTRIFUGAL FORCE, 67'' WIDE (ADD 180 HP TOWING UNIT)

HP D-off

ROLLERS, VIBRATORY, SELF-PROPELLED, DOUBLE DRUMR450.00 ROLLERS, VIBRATORY, SELF-PROPELLED, DOUBLE DRUMSUBCATEGORY


33BW120AD-4R45BO004 $39,721 3.97 0.42 4.82 572.4115.88ROLLER, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM, SMOOTH, 2.9 TON, 47.2" WIDE, 2X1, ASPHALT COMPACTOR

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-183


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)


46BW138ADR45BO005 $58,424 5.84 0.61 6.73 923.5322.94ROLLER, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM, SMOOTH, 4.6 TON, 54.3" WIDE, 2X1, ASPHALT COMPACTOR

HP D-off


HP D-off


HP D-off

205BW190AD-4 HFR45BO008 $150,624 15.06 1.59 29.97 2529.1273.56ROLLER, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM, SMOOTH, 12.6 TON, 79.0" WIDE, 2X1, ASPHALT COMPACTOR

HP D-off


32CB-214DR45CA001 $51,136 5.11 0.54 4.68 813.1018.70ROLLER, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM, SMOOTH, 2.5 TON, 39.4" WIDE, 2X1, ASPHALT COMPACTOR

HP D-off

32CB-224DR45CA002 $58,560 5.86 0.62 4.68 583.5520.65ROLLER, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM, SMOOTH, 2.7 TON, 47.2" WIDE, 2X1, ASPHALT COMPACTOR

HP D-off

70CB-434DR45CA005 $120,294 12.03 1.27 10.23 1377.2943.10ROLLER, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM, SMOOTH, 6.6 TON, 56" WIDE, 2X1, ASPHALT COMPACTOR

HP D-off

105CB-534CR45CA007 $172,833 17.28 1.82 15.35 23310.4662.66ROLLER, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM, SMOOTH, 10.0 TON, 67" WIDE, 2X1, ASPHALT COMPACTOR

HP D-off

145CB-634DR45CA010 $214,959 21.50 2.26 21.20 28313.0180.36ROLLER, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM, SMOOTH, 13.2 TON, 84" WIDE, 2X1, ASPHALT COMPACTOR

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-184


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT


20300BR45RS001 $20,496 2.05 0.22 2.92 261.258.69ROLLER, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM, SMOOTH, 2.0 TON, 36" WIDE, ASPHALT COMPACTOR

HP D-off

SAKAI AMERICA, INC.

35SW320-1R45SI008 $39,530 3.95 0.42 5.12 282.4016.17ROLLER, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM, SMOOTH, 3.0 TON, 47" WIDE, 2X1, ASPHALT COMPACTOR

HP D-off

78SW652R45SI009 $107,627 10.76 1.13 11.40 1576.5141.12ROLLER, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM, SMOOTH, 7.8 TON, 58" WIDE, 2X1, ASPHALT COMPACTOR

HP D-off

127SW850-3R45SI010 $144,304 14.43 1.52 18.57 1248.7458.89ROLLER, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM, SMOOTH, 14.0 TON, 79" WIDE, 2X1, ASPHALT COMPACTOR

HP D-off

ROLLERS, VIBRATORY, SELF-PROPELLED, SINGLE DRUMR500.00 ROLLERS, VIBRATORY, SELF-PROPELLED, SINGLE DRUMSUBCATEGORY


50BW124DH-40R50BO005 $57,015 4.70 0.62 5.27 602.9720.54ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, SMOOTH, 2.9 TON, 47.2" WIDE, 3X2, SOIL COMPACTOR

HP D-off

50BW124PDH-40R50BO010 $58,901 5.35 0.64 5.27 603.3220.43ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, PAD FOOT, 2.9 TON, 47.2" WIDE, 3X2, SOIL COMPACTOR

HP D-off

75BW145D-40R50BO006 $83,995 7.80 0.91 7.91 1104.8129.41ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, SMOOTH, 5.5 TON, 56.1" WIDE, 3X2, SOIL COMPACTOR

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-185


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)



HP D-off

75BW177D-40R50BO007 $97,861 8.98 1.06 7.91 1595.5532.89ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, SMOOTH, 7.9 TON, 66.4" WIDE, 3X2, SOIL COMPACTOR

HP D-off


HP D-off


HP D-off


HP D-off


HP D-off


70CS-323CR50CA001 $88,503 8.17 0.96 7.38 975.0529.94ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, SMOOTH, 4.6 TON, 50" WIDE, 3X2, SOIL COMPACTOR

HP D-off

97CS-431CR50CA003 $126,601 11.65 1.37 10.22 1387.2042.50ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, SMOOTH, 6.9 TON, 66" WIDE, 3X2, SOIL COMPACTOR

HP D-off

100CS-433ER50CA005 $124,551 11.46 1.35 10.54 1477.0842.38ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, SMOOTH, 7.1 TON, 66" WIDE, 3X2, SOIL COMPACTOR

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-186


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT



HP D-off


HP D-off

70CP-323C (PADS)R50CA002 $97,967 9.06 1.06 7.38 1055.5932.23ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, PAD FOOT, 4.6 TON, 50" WIDE, 3X2, SOIL COMPACTOR

HP D-off

150CP-563E (PADS)R50CA010 $208,212 18.94 2.26 15.81 26211.7369.01ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, PAD FOOT, 12.5 TON, 84" WIDE, 3X2 SOIL COMPACTOR

HP D-off

100CP-433E (PADS)R50CA004 $139,491 12.86 1.51 10.54 1507.9445.98ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, PAD FOOT, 7.1 TON, 66" WIDE, 3X2, SOIL COMPACTOR

HP D-off

150CP-563E (PADS)R50CA012 $208,420 18.96 2.26 15.81 27511.7469.06ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, PAD FOOT, 12.5 TON, 84" WIDE, 3X2, SOIL COMPACTOR

HP D-off

INGERSOLL RAND ROAD MACHINERY DIV

80SD-45DR50IP001 $98,061 8.94 1.06 8.43 1045.5333.61ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, SMOOTH, 4.9 TON, 54" WIDE, SOIL COMPACTOR

HP D-off

SAKAI AMERICA, INC.

28TW350 ComboR50SI024 $62,288 5.69 0.68 2.95 253.5318.58ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, SMOOTH, 1.5 TON, 39.5" WIDE, 2X1, ASPHALT COMPACTOR

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-187


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

R50 SAKAI AMERICA, INC. (continued)30TW500 ComboR50SI025 $76,880 7.06 0.83 3.16 364.3622.34ROLLER, VIBRATORY, SELF-PROPELLED,

SINGLE DRUM, SMOOTH, 3.9 TON, 51" WIDE, 2X1, ASPHALT COMPACTOR

HP D-off

60SV201DR50SI006 $81,588 7.41 0.89 6.32 414.6027.22ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, SMOOTH, 4.8 TON, 54" WIDE, 3X2, SOIL COMPACTOR

HP D-off

60SV201T (PADS)R50SI007 $87,376 7.95 0.95 6.32 434.9328.61ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, SMOOTH, 4.9 TON, 54" WIDE, 3X2, SOIL COMPACTOR

HP D-off

100SV400D-2R50SI022 $111,336 10.21 1.21 10.54 1566.3239.20ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, SMOOTH, 7.7 TON, 67" WIDE, 3X2, SOIL COMPACTOR

HP D-off

104TW750 ComboR50SI026 $152,937 14.19 1.66 10.96 1008.7649.62ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, SMOOTH, 8.7 TON, 66" WIDE, 2X1, ASPHALT COMPACTOR

HP D-off

100SV400TB-2 (PADS)

R50SI023 $124,795 11.47 1.35 10.54 727.0942.44ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, SMOOTH, 9.6 TON, 67" WIDE, 3X2, SOIL COMPACTOR

HP D-off

148SV510D-3R50SI013 $134,440 11.96 1.46 15.60 5077.4451.03ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, SMOOTH, 11.5 TON, 84" WIDE, 3X2, SOIL COMPACTOR

HP D-off

148SV510T-3 (PADS)


HP D-off

148SV510TF-3 (PADS)


HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-188


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

ROOFING EQUIPMENTR550.00 ROOFING EQUIPMENTSUBCATEGORY

GARLOCK EQUIPMENT CO.

5300628R55GL020 $5,038 0.62 0.05 0.97 40.362.53ROOFING EQUIPMENT, MATERIAL BUGGY, 36'' WIDE, WALK BEHIND GRAVEL SPREADER, HOPPER 800 LBS, 8 CF, 4X2

HP G

9Ultracutter 300645

R55GL021 $2,964 0.42 0.03 1.75 20.242.81ROOFING EQUIPMENT, 1-BLADE CUTTER, 3.75" DEEP, WALK BEHIND 11 HP (ADD BLADE COST)

HP G

8GENESIS 1012R55GL022 $28,777 3.89 0.30 1.56 542.2517.19ROOFING EQUIPMENT, KETTLE, 1,012 GAL, W/PUMP, TRAILER MTD

HP G

8ROOF WARRIOR

R55GL023 $8,560 1.17 0.09 1.56 60.684.26ROOFING EQUIPMENT, ROOF PEELER, 16" WIDE, WALK BEHIND, POWERED WHEEL 2X2, STD W/ 18" FLAT BLADE

HP G

5SUPER MINI SAW

R55GL017 $2,432 0.34 0.03 0.97 20.201.80ROOFING EQUIPMENT, 1-BLADE CUTTER, 18" HEIGHT & 2" WALL CLEARANCE

HP G

9DUST MASTER ULTRA CU

R55GL016 $5,542 0.79 0.06 1.75 30.463.59ROOFING EQUIPMENT, 1-BLADE CUTTER, W/WATER DAMPENING SYSTEM AND H.E.P.A. VACUUM SYSTEM

HP G

16ENFORCER TWIN CUTTER

R55GL011 $7,926 1.12 0.08 3.12 40.645.81ROOFING EQUIPMENT, 2-BLADE CUTTER, 25" WIDE, SELF PROPELLED (ADD BLADE COST)

HP G

5NO.12R55GL018 $2,749 0.39 0.03 0.97 10.231.89ROOFING EQUIPMENT, SCRATCHER, 4.5" WIDE

HP G

8NO. 30R55GL019 $5,365 0.76 0.06 1.56 30.443.33ROOFING EQUIPMENT, SCRATCHER, 13" WIDE

HP G

EP 1110-1-8, Vol. 430 Nov 11

2-189


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

R55 GARLOCK EQUIPMENT CO. (continued)11ROTARY

PLANERR55GL009 $3,152 0.45 0.03 2.05 20.263.21ROOFING EQUIPMENT, ROTARY PLANER,

12" WIDE HP G

9MODEL 1000R55GL015 $13,037 1.85 0.14 1.75 81.075.83ROOFING EQUIPMENT, HYDRAULIC HOIST, W/175' CABLE, 1,000 LB CAP

HP G

18SUPER MAX HYDR HOIST

R55GL007 $13,884 1.97 0.15 3.51 101.148.03ROOFING EQUIPMENT, HYDRAULIC SWING HOIST, W/275' CABLE, 1,400 LB CAP

HP G

MODEL 30R55GL013 $1,871 0.15 0.02 0.00 30.100.74ROOFING EQUIPMENT, KETTLE, 30 GAL, WHEEL MTD

MODEL 90R55GL014 $4,170 0.59 0.04 0.00 70.341.59ROOFING EQUIPMENT, KETTLE, 90 GAL, SKID MTD

MODEL 115 R55GL001 $4,891 0.67 0.05 0.00 80.391.95ROOFING EQUIPMENT, KETTLE, 115 GAL, TRAILER MTD

5MODEL 175 R55GL002 $6,768 0.91 0.07 0.97 170.533.56ROOFING EQUIPMENT, KETTLE, 175 GAL, W/PUMP, TRAILER MTD

HP G

9MODEL 300R55GL012 $12,815 1.76 0.14 1.75 231.026.48ROOFING EQUIPMENT, KETTLE, 300 GAL, W/PUMP, TRAILER MTD

HP G

9GENESIS 412R55GL003 $18,150 2.53 0.19 1.75 301.468.07ROOFING EQUIPMENT, KETTLE, 412 GAL, W/PUMP, TRAILER MTD

HP G

9GENESIS 612R55GL004 $22,098 3.09 0.23 1.75 401.789.50ROOFING EQUIPMENT, KETTLE, 612 GAL, W/PUMP, TRAILER MTD

HP G

EP 1110-1-8, Vol. 430 Nov 11

2-190


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

SCRAPERS, ELEVATINGS100.01 0 THRU 200 HPSUBCATEGORY


175613-C SERIES IIS10CA001 $303,544 23.58 3.13 18.45 33614.9281.90SCRAPER, ELEVATING LOADING, 11 CY, 13 TON, 7.7' CUT WIDTH, 4X2 - SINGLE POWERED

HP D-off

0.02 OVER 200 HPSUBCATEGORY


265615-C SERIES IIS10CA002 $451,354 23.92 4.74 27.93 52616.70111.05SCRAPER, ELEVATING LOADING, 17 CY, 19 TON, 9.5' CUT WIDTH, 4X2 - SINGLE POWERED

HP D-off

365623-GS10CA003 $491,075 26.59 5.15 38.47 81018.45126.97SCRAPER, ELEVATING LOADING, 23 CY, 25 TON, 11.5' CUT WIDTH, 4X2 - SINGLE POWERED

HP D-off

SCRAPERS, CONVENTIONALS150.00 SCRAPERS, CONVENTIONALSUBCATEGORY


365621-GS15CA001 $580,058 29.43 5.84 35.99 71420.56122.59SCRAPER, CONVENTIONAL, STANDARD LOADING, 21 CY, 24 TON, 9.1' CUT WIDTH, 4X2 - SINGLE POWERED

HP D-off

450631-GS15CA002 $844,967 42.98 8.50 44.37 1,02029.99168.70SCRAPER, CONVENTIONAL, STANDARD LOADING, 34 CY, 37.5 TON, 11.5' CUT WIDTH, 4X2 - SINGLE POWERED

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-191


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

S15 CATERPILLAR INC. ( MACHINE DIVISION) (continued)

550651-ES15CA003 $1,100,517 55.37 11.08 54.23 1,32338.77219.63SCRAPER, CONVENTIONAL, STANDARD LOADING, 44 CY, 52 TON, 12.6' CUT WIDTH, 4X2 - SINGLE POWERED

HP D-off

ATI-Bell

4224206DTIS28S15JU001 $589,255 30.57 5.93 41.61 94021.22123.31SCRAPER, CONVENTIONAL, STANDARD LOADING, 28 CY, 32 TON, 14' CUT WIDTH, 4X4 - SINGLE POWERED, TRACTOR EQUIPPED WITH ATI RUBBER TRACKS

HP D-off

4224206DTIS33S15JU002 $609,850 31.66 6.14 41.61 95321.97125.85SCRAPER, CONVENTIONAL, STANDARD LOADING, 33 CY, 37 TON, 14' CUT WIDTH, 4X4 - SINGLE POWERED, TRACTOR EQUIPPED WITH ATI RUBBER TRACKS

HP D-off

SCRAPERS, TANDEM POWEREDS200.00 SCRAPERS, TANDEM POWEREDSUBCATEGORY


330627-GS20CA001 $486,438 24.44 4.90 56.61 79117.12138.15225 HP D-offSCRAPER, TANDEM POWERED, STANDARD LOADING, 21 CY, 24 TON, 9.1' CUT WIDTH, 4X4, D-9 ASSISTED LOADING

HP D-off

330627-G PPS20CA002 $696,523 35.64 7.01 56.61 82424.83164.85225 HP D-offSCRAPER, TANDEM POWERED, STANDARD LOADING, 20 CY, 24 TON, 9.1' CUT WIDTH, 4X4, PUSH-PULL

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-192


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

S20 CATERPILLAR INC. ( MACHINE DIVISION) (continued)

450637-GS20CA003 $1,081,269 55.58 10.88 71.40 1,08438.67235.38250 HP D-offSCRAPER, TANDEM POWERED, STANDARD LOADING, 34 CY, 37.5 TON, 11.5' CUT WIDTH, 4X4, D-10 ASSISTED LOADING

HP D-off

450637-G PPS20CA004 $1,126,136 57.97 11.33 71.40 1,11740.32241.08250 HP D-offSCRAPER, TANDEM POWERED, STANDARD LOADING, 34 CY, 37.5 TON, 11.5' CUT WIDTH, 4X4, PUSH-PULL

HP D-off

550657-GS20CA005 $1,385,519 70.42 13.94 96.90 1,51649.15314.59400 HP D-offSCRAPER, TANDEM POWERED, STANDARD LOADING, 44 CY, 52 TON, 12.6' CUT WIDTH, 4X4, D-11 ASSISTED LOADING

HP D-off

550657-G PPS20CA006 $1,469,985 75.08 14.79 96.90 1,55052.33324.02400 HP D-offSCRAPER, TANDEM POWERED, STANDARD LOADING, 44 CY, 52 TON, 12.6' CUT WIDTH, 4X4, PUSH-PULL

HP D-off

SCRAPERS, TRACTOR DRAWNS250.00 SCRAPERS, TRACTOR DRAWNSUBCATEGORY

DEERE & COMPANY

1510CS25JD001 $55,883 3.37 0.57 0.00 1682.2610.39SCRAPER, TOWED, STANDARD LOADING, 11 CY, 17 TON, 10' CUT WIDTH (ADD 225 HP TRACTOR)

1814CS25JD002 $69,972 4.14 0.71 0.00 2132.7812.87SCRAPER, TOWED, STANDARD LOADING, 14 CY, 23 TON, 14' CUT WIDTH (ADD 360HP TRACTOR)

EP 1110-1-8, Vol. 430 Nov 11

2-193


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

REYNOLDS INTERNATIONAL, L.P.

14CS10S25RI001 $46,119 2.96 0.47 0.00 1381.958.37SCRAPER, TOWED, PIVOT DUMP, 10.7-14 CY, 15 TON, 10' CUT WIDTH (ADD 250 - 300 HP TRACTOR)

17C12 (RG)S25RI002 $51,961 3.30 0.53 0.00 1702.189.35SCRAPER, TOWED, PIVOT DUMP, 13-17 CY, 17 TON, 12' CUT WIDTH (ADD 350 - 400 HP TRACTOR)

ROME PLOW CO.

R56HS25RM003 $98,253 5.63 1.00 0.00 2033.8218.81SCRAPER, TOWED, 9-12 CY, 12.5 TON, 8.5' CUT WIDTH (ADD 120-165 HP TRACTOR)

R67H S25RM001 $130,219 7.76 1.33 0.00 2385.2123.36SCRAPER, TOWED, 12-17 CY, 17 TON, 9.9' CUT WIDTH (ADD 165-215 HP TRACTOR)

R89HS25RM002 $192,341 11.26 1.96 0.00 3827.5934.26SCRAPER, TOWED, 18-26 CY, 25 TON, 10.8' CUT WIDTH (ADD 285-370 HP TRACTOR)

SCREENING & CRUSHING PLANTSS300.10 CONVEYORSSUBCATEGORY


1512-3050S30KB034 $58,002 4.85 0.56 0.79 152.9911.48SCREENING & CRUSHING PLANTS, FEEDER CONVEYOR, 30" WIDE X 50' LONG, 7 CY HOPPER & 6' FEED, PORTABLE, 500 TPH

HP E

EP 1110-1-8, Vol. 430 Nov 11

2-194


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

S30 KOLBERG - PIONEER, INC (continued)2012-3070S30KB035 $66,146 5.52 0.64 1.05 183.4013.32SCREENING & CRUSHING PLANTS,

FEEDER CONVEYOR, 30" WIDE X 70' LONG, 7 CY HOPPER & 6' FEED, PORTABLE, 500 TPH

HP E


HP E


HP E

1013-2480S30KB001 $38,211 3.17 0.37 0.53 141.967.57SCREENING & CRUSHING PLANTS, CONVEYOR, STACKING, 24" WIDE X 80' LONG, PORTABLE, 250 TPH

HP E


HP E


HP E


HP E


HP E


HP E

EP 1110-1-8, Vol. 430 Nov 11

2-195


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)


CONVEYOR, SIDE FOLDING STACKER, 24" WIDE X 80' LONG, WHEEL MTD, 750 TPH

HP E

1531-24100S30KB008 $54,006 4.57 0.52 0.79 272.8110.75SCREENING & CRUSHING PLANTS, CONVEYOR, SIDE FOLDING STACKER, 24" WIDE X 100' LONG, PORTABLE, 250 TPH

HP E


HP E


HP E


HP E


HP E


HP E

EP 1110-1-8, Vol. 430 Nov 11

2-196


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT


CONVEYOR, SIDE FOLDING STACKER, 36" WIDE X 100' LONG, PORTABLE, 750 TPH

HP E


HP E

2535-24150S30KB018 $110,370 9.53 1.06 1.32 395.8321.51SCREENING & CRUSHING PLANTS, CONVEYOR, FIXED HEIGHT STACKER, 24" WIDE X 150' LONG, PORTABLE, 750 TPH

HP E

4035-30150S30KB021 $127,920 11.06 1.23 2.11 566.7625.82SCREENING & CRUSHING PLANTS, CONVEYOR, FIXED HEIGHT STACKER, 30" WIDE X 150' LONG, PORTABLE, 1,500 TPH

HP E

6035-36150S30KB024 $146,596 12.70 1.41 3.16 847.7630.70SCREENING & CRUSHING PLANTS, CONVEYOR, FIXED HEIGHT STACKER, 36" WIDE X 150' LONG, PORTABLE, 2,000 TPH

HP E

2036-24100S30KB025 $78,620 6.74 0.76 1.05 524.1315.50SCREENING & CRUSHING PLANTS, CONVEYOR, ADJUSTABLE HEIGHT RADIAL STACKER, 24" WIDE X 100' LONG, PORTABLE, 750 TPH

HP E

2036-24125S30KB026 $93,425 8.05 0.90 1.05 574.9318.12SCREENING & CRUSHING PLANTS, CONVEYOR, ADJUSTABLE HEIGHT RADIAL STACKER, 24" WIDE X 120' LONG, PORTABLE, 750 TPH

HP E

EP 1110-1-8, Vol. 430 Nov 11

2-197


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)


CONVEYOR, ADJUSTABLE HEIGHT RADIAL STACKER, 24" WIDE X 150' LONG, PORTABLE, 750 TPH

HP E

3036-30100S30KB028 $89,402 7.68 0.86 1.58 644.7018.20SCREENING & CRUSHING PLANTS, CONVEYOR, ADJUSTABLE HEIGHT RADIAL STACKER, 30" WIDE X 100' LONG, PORTABLE, 1,500 TPH

HP E


HP E


HP E


HP E


HP E


HP E

EP 1110-1-8, Vol. 430 Nov 11

2-198


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

S30 KOLBERG - PIONEER, INC (continued)301430-60-25S30KB042 $98,309 8.52 0.95 1.58 185.2119.77SCREENING & CRUSHING PLANTS,

SURGE BIN, 25CY, BELT FEEDER, & 30" WIDE X 60' LONG CONVEYOR, PORTABLE, 1,500 TPH

HP E

151936-2S30KB054 $100,623 8.72 0.97 0.79 185.3318.99SCREENING & CRUSHING PLANTS, SURGE BIN, 25CY, BELT FEEDER, & 30" WIDE X 40' LONG CONVEYOR, PORTABLE, 1,500 TPH

HP E

401436-60-25S30KB053 $101,568 8.78 0.98 2.11 205.3721.14SCREENING & CRUSHING PLANTS, SURGE BIN, 25CY, BELT FEEDER, & 36" WIDE X 60' LONG CONVEYOR, PORTABLE, 2,000 TPH

HP E


HP E


HP E

PUTZMEISTER INC.

400TELEBELT TB 130

S30PU004 $877,428 78.41 8.45 42.16 76347.66202.61SCREENING & CRUSHING PLANTS, CONVEYOR, 18" WIDE X 126' LONG, 3 CY HOPPER & TREMIE, 4X8, TRUCK MTD, 360 CY/HR

HP D-off

400TELEBELT TB 80

S30PU002 $594,706 53.02 5.73 42.16 52032.24152.71SCREENING & CRUSHING PLANTS, CONVEYOR, 18" WIDE X 80' LONG, 3 CY HOPPER & TREMIE, 4X6, TRUCK MTD, 360 CY/HR

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-199


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

S30 PUTZMEISTER INC. (continued)400TELEBELT TB

110S30PU003 $748,059 66.77 7.21 42.16 61540.60179.79SCREENING & CRUSHING PLANTS,

CONVEYOR, 18" WIDE X 106' LONG, 3 CY HOPPER & TREMIE, 4X8, TRUCK MTD, 360 CY/HR

HP D-off

TELSMITH INC.

12PTC 24IN X 50FT

S30TS001 $39,997 3.38 0.39 0.63 102.088.04SCREENING & CRUSHING PLANTS, CONVEYOR, TRUSS FRAME, 24" WIDE X 50' LONG, WHEEL MTD, 300 TPH

HP E

17PTC 24IN X 70FT


HP E

17PTC 30IN X 50FT


HP E

22PTC 30IN X 70FT

S30TS004 $56,113 4.73 0.54 1.16 172.9111.72SCREENING & CRUSHING PLANTS, CONVEYOR, TRUSS FRAME, 30" WIDE X 70' LONG, WHEEL MTD, 1,000 TPH

HP E

22PTC 36IN X 50FT


HP E

27PTC 36IN X 70FT


HP E

32PTC 42IN X 50FT


HP E

42PTC 42IN X 70FT


HP E

EP 1110-1-8, Vol. 430 Nov 11

2-200


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

0.20 CRUSHERS - VERTICAL & HORIZONTAL SHAFT IMPACTORSUBCATEGORY

HEWITT-ROBINS

250MODEL 13654VS30HW001 $344,385 12.09 3.13 13.16 8049.1851.15SCREENING & CRUSHING PLANTS, CRUSHER - SHAFT IMPACTOR, 36"X54", SINGLE ROTOR, 250 TPH, W/3' X 16' FEEDER/ 4' GRIZZLY/ 24" X 8' REJECTION CONVEYOR/ & 36" X 37' DISCHARGE END DELIVERY CONVEYOR, TRAILER MTD (ADD 250 KW GENERATOR)

HP E

350MODEL 14866VS30HW002 $464,208 16.33 4.22 18.43 1,28012.3969.89SCREENING & CRUSHING PLANTS, CRUSHER - SHAFT IMPACTOR, 48"X66" SINGLE ROTOR, 350 TPH, W/4'X16' FEEDER/ 6' GRIZZLY/ 30" X 9.5' REJECTION CONVEYOR/ & 48" X43' DISCHARGE END DELIVERY CONVEYOR, TRAILER MTD (ADD 350 KW GENERATOR)

HP E

450MODEL H4832SS30HW013 $416,620 14.69 3.79 23.69 60011.1473.30SCREENING & CRUSHING PLANTS, CRUSHER - SHAFT IMPACTOR, SECONDARY, 48"X32" HAMMERMILL, 500 TPH, W/3' X 37' FEED CONVEYOR/ 5' X 16' VIBRATORY HORIZONTAL TRIPLE DECK SCREEN/ 36"X30' RETURN CONVEYOR/ & ROTOR LIFT, TRAILER MTD (ADD 450 KW GENERATOR)

HP E


360CS-4250S30KB045 $595,370 21.19 5.42 37.94 54816.0296.22SCREENING & CRUSHING PLANTS, CRUSHER - SHAFT IMPACTOR, 42" X 52", 500 TPH, W/18' X 42" VIBRATORY FEEDER/ ADJUSTABLE GRIZZLY/ & BYPASS FEED, TRAILER MTD

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-201


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

TELSMITH INC.

3004246S30TS009 $317,020 11.41 2.88 15.80 5958.5954.85SCREENING & CRUSHING PLANTS, CRUSHER - SHAFT IMPACTOR, 46'' X 59'', 600 TPH

HP E

4004856S30TS010 $465,068 16.74 4.23 21.06 94212.6076.91SCREENING & CRUSHING PLANTS, CRUSHER - SHAFT IMPACTOR, 56'' X 85'', 1,100 TPH

HP E

8006071S30TS011 $770,176 27.73 7.00 42.12 1,95020.87139.57SCREENING & CRUSHING PLANTS, CRUSHER - SHAFT IMPACTOR, 71'' X 100'', 2,100 TPH

HP E

0.21 CRUSHERS - CONESUBCATEGORY


2721200 LSS30KB046 $412,569 14.56 3.75 14.32 81011.0362.44SCREENING & CRUSHING PLANTS, CRUSHERS - CONE, SECONDARY, 120 TPH @ 3/8" -> 250 TPH @ 1", 42" X 50" IMPACT CRUSHER, W/HOPPER/ & 36" X 32' END DELIVERY CONVEYOR, TRAILER MTD (ADD 210KW GENERATOR)

HP E

3151400 LSS30KB047 $518,277 18.44 4.71 16.58 74113.9376.02SCREENING & CRUSHING PLANTS, CRUSHERS - CONE, SECONDARY PLANT, 630 TPH @ 1" ->1,050 TPH @ 2.5", 42" X 50" IMPACT CRUSHER, W/HOPPER/ & 42" X 32' END DELIVERY CONVEYOR, TRAILER MTD (INCLUDES GENERATOR)

HP E

EP 1110-1-8, Vol. 430 Nov 11

2-202


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

0.22 CRUSHERS - JAWSUBCATEGORY

HEWITT-ROBINS

40MODEL J1524PFS30HW005 $187,073 6.55 1.70 2.11 864.9817.50SCREENING & CRUSHING PLANTS, JAW CRUSHER, 15"X24", 21 TPH @ 1" -> 54 TPH @ 3", W/2.5' X 8' FEEDER/ 2' GRIZZLY/ & 24" X 20' END DELIVERY CONVEYOR, TRAILER MTD (ADD 40 KW GENERATOR)

HP E

100MODEL J1536VS30HW006 $311,386 11.01 2.83 5.27 1288.3431.41SCREENING & CRUSHING PLANTS, JAW CRUSHER, 15"X36", 45 TPH @1.5" -> 150 TPH @ 6", W/3' X 14' FEEDER/ 4' GRIZZLY/ & 30" X 31' END DELIVERY CONVEYOR, TRAILER MTD (ADD 40 KW GENERATOR)

HP E

125MODEL J2036VS30HW007 $338,368 11.98 3.08 6.58 1289.0735.36SCREENING & CRUSHING PLANTS, JAW CRUSHER, 20" X 36", 65 TPH @ 2" -> 223 TPH @ 7", W/3' X 14' FEEDER/ 4' GRIZZLY/ & 30" X 31' END DELIVERY CONVEYOR, TRAILER MTD (ADD 40 KW GENERATOR)

HP E

150MODEL J2142VS30HW009 $366,659 12.90 3.33 7.90 1529.7839.69SCREENING & CRUSHING PLANTS, JAW CRUSHER, 21" X 42", 183 TPH @ 4" -> 345 TPH @ 8", W/3.5' X 16' FEEDER/ 4' GRIZZLY/ & 36" X 34' END DELIVERY CONVEYOR, TRAILER MTD (ADD 40 KW GENERATOR)

HP E

200MODEL J2248VS30HW011 $438,040 15.43 3.98 10.53 16811.7049.05SCREENING & CRUSHING PLANTS, JAW CRUSHER, 22" X 48", 115 TPH @ 2.5" -> 240 TPH @ 6", W/4' X 16' FEEDER/ 4' GRIZZLY/ & 48" X 37' END DELIVERY CONVEYOR (ADD 40 KW GENERATOR)

HP E

EP 1110-1-8, Vol. 430 Nov 11

2-203


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

S30 HEWITT-ROBINS (continued)125MODEL J2436VS30HW008 $353,513 12.53 3.22 6.58 1289.4936.48SCREENING & CRUSHING PLANTS, JAW

CRUSHER, 24" X 36", 95 TPH @ 2.5" -> 230 TPH @ 6", W/3' X 14' FEEDER/ 4' GRIZZLY/ & 30" X 31' END DELIVERY CONVEYOR, TRAILER MTD (ADD 40 KW GENERATOR)

HP E

200MODEL J3042VS30HW010 $446,750 15.76 4.06 10.53 15611.9449.64SCREENING & CRUSHING PLANTS, JAW CRUSHER, 30" X 42", 200 TPH @ 4" -> 390 TPH @ 8", W/3.5' X 16' FEEDER/ 6' GRIZZLY/ & 36" X 55' END DELIVERY CONVEYOR, TRAILER MTD (ADD 40 KW GENERATOR)

HP E

200MODEL J3048VS30HW012 $517,675 18.26 4.71 10.53 16813.8455.03SCREENING & CRUSHING PLANTS, JAW CRUSHER, 30" X 48", 340 TPH @ 5" -> 615 TPH @ 10", W/4' X 16' FEEDER/ 4' GRIZZLY/ & 48" X 37' END DELIVERY CONVEYOR, TRAILER MTD (ADD 40 KW GENERATOR)

HP E


245CS-1536S30KB055 $386,887 13.73 3.52 25.82 54810.3958.11SCREENING & CRUSHING PLANTS, JAW CRUSHER, 15" X 36", 45 TPH @ 1.5" -> 150 TPH @ 6", W/36"' X 14' VIBRATING FEEDER/ ADJUSTABLE GRIZZLY & BYPASS/ HOPPER/ & 36" X 22' END DELIVERY CONVEYOR, TRAILER MTD, INCLUDES GENERATOR

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-204


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

S30 KOLBERG - PIONEER, INC (continued)1301524-2416

DUPLEX PLS30KB058 $413,981 14.72 3.77 6.84 39111.1341.32SCREENING & CRUSHING PLANTS, JAW

CRUSHER, 15" X 36", 200 TPH @ 1/4" -> 250 TPH @ 6", W/36" X 14' VIBRATING FEEDER/ ADJUSTABLE GRIZZLY & BYPASS/ HOPPER/ SCREEN CONVEYOR/ & TRIPLE VIBRATORY SCREENS, TRAILER MTD

HP E

245CS-2036S30KB056 $396,518 14.07 3.61 25.82 59010.6558.81SCREENING & CRUSHING PLANTS, JAW CRUSHER, 20" X 36", 65 TPH @ 2" -> 223 TPH @ 7", W/36"' X 14' VIBRATING FEEDER/ ADJUSTABLE GRIZZLY & BYPASS/ HOPPER/ & 36" X 22' END DELIVERY CONVEYOR, TRAILER MTD, INCLUDES GENERATOR

HP D-off

3002036-3024 DUPLEX PL

S30KB059 $649,326 23.11 5.91 15.80 41517.4772.29SCREENING & CRUSHING PLANTS, JAW CRUSHER, 20" X 36", 270 TPH @ 1/4" -> 320 TPH @ 7", W/36" X 14' RECIPROCATING PLATE FEEDER/ 12' LONG ADJUSTABLE GRIZZLY & BYPASS/ HOPPER/ & 18" X 15' SCREEN CONVEYOR, TRAILER MTD (ADD 300KW GENERATOR)

HP E

245CS-2436S30KB057 $442,146 15.72 4.02 25.82 70111.8862.18SCREENING & CRUSHING PLANTS, JAW CRUSHER, 24" X 36", 95 TPH @ 2.5" -> 230 TPH @ 6", W/36"' X 16' VIBRATING FEEDER/ ADJUSTABLE GRIZZLY & BYPASS/ HOPPER/ & 36" X 22' END DELIVERY CONVEYOR, TRAILER MTD, INCLUDES GENERATOR

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-205


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

0.30 SCREENING PLANTSUBCATEGORY

HEWITT-ROBINS

15V-11 6X16FT, DD

S30HW014 $135,922 11.93 1.31 0.79 1017.2826.67SCREENING & CRUSHING PLANTS, SCREENING PLANT, 6' X 16' VIBRATORY SLOPE DOUBLE DECK SCREENS, W/36" X 16.5' UNDER SCREEN CONVEYOR/ 7 CY HOPPER/ & FEEDER, TRAILER MTD

HP E

20V-11 6X20FT, DD

S30HW016 $141,366 12.42 1.36 1.05 1157.5728.08SCREENING & CRUSHING PLANTS, SCREENING PLANT, 6' X 20' VIBRATORY SLOPE DOUBLE DECK SCREENS, W/36" X 16.5' UNDER SCREEN CONVEYOR/ 7 CY HOPPER/ & FEEDER, TRAILER MTD

HP E

25V-11 6X16FT, TDS30HW015 $149,344 13.14 1.44 1.32 1388.0129.98SCREENING & CRUSHING PLANTS, SCREENING PLANT, 6' X 16' VIBRATORY SLOPE TRIPLE DECK SCREENS W/36" X 16.5' UNDER SCREEN CONVEYOR/ 7 CY HOPPER/ & FEEDER, TRAILER MTD

HP E

25V-11 6X20FT, TDS30HW017 $151,993 13.38 1.46 1.32 1678.1530.48SCREENING & CRUSHING PLANTS, SCREENING PLANT, 6' X 20' VIBRATORY SLOPE TRIPLE DECK SCREENS W/36" X 16.5' UNDER SCREEN CONVEYOR/ 7 CY HOPPER/ & FEEDER, TRAILER MTD,

HP E

40V-11 8X20FT, TDS30HW018 $181,060 15.74 1.74 2.11 2439.6137.12SCREENING & CRUSHING PLANTS, SCREENING PLANT, 8' X 20' VIBRATORY SLOPE TRIPLE DECK SCREENS, W/48" X 15.5' UNDER SCREEN CONVEYOR/ 7 CY HOPPER/ & FEEDER, TRAILER MTD

HP E

EP 1110-1-8, Vol. 430 Nov 11

2-206


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT


85616 E-3S30KB048 $183,394 16.09 1.77 4.48 2809.8241.12SCREENING & CRUSHING PLANTS, SCREENING PLANT, 6' X 16', VIBRATORY SLOPE TRIPLE DECK SCREENS, W/HOPPER/ 36" X 28.5' FEEDER CONVEYOR/ 48" X27' UNDER SCREEN CONVEYOR/ & 24" X 20' SIDE DELIVERY CONVEYOR, TRAILER MTD

HP E

90620 E-3S30KB049 $216,328 18.05 2.08 4.74 35511.1147.85SCREENING & CRUSHING PLANTS, SCREENING PLANT, 6' X 20' VIBRATORY SLOPE TRIPLE DECK SCREENS, W/HOPPER/ 42" X 34' FEEDER CONVEYOR/ 60" X 25' UNDER SCREEN CONVEYOR/ & 30" X 15' SIDE DELIVERY CONVEYOR, TRAILER MTD

HP E

2501822S30KB050 $260,985 23.09 2.51 13.16 41614.0668.62SCREENING & CRUSHING PLANTS, WASHING/SCREENING PLANT, 6' X 16' VIBRATORY SLOPE TRIPLE DECK SCREENS, W/HOPPER / 3 PRODUCT CHUTES/ ONE FINES CHUTE TO 8' X 32' CLASSIFYING TANK/ 36" DIA X 32' SLOPED SCREW & CHUTE, TRAILER MTD (ADD WATER & FEEDER)

HP E

2501830S30KB051 $331,598 29.24 3.19 13.16 42017.8181.84SCREENING & CRUSHING PLANTS, WASHING/SCREENING PLANT, 6' X 20' VIBRATORY SLOPED TRIPLE DECK SCREENS, W/HOPPER/ 3 PRODUCT CHUTES/ ONE FINES CHUTE/ 8' X 32' CLASSIFYING TANK/ & 44" DIA X 32' SLOPED SCREW & CHUTE, TRAILER MTD (ADD WATER & FEEDER)

HP E

EP 1110-1-8, Vol. 430 Nov 11

2-207


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

S30 KOLBERG - PIONEER, INC (continued)2507208-32 S/PS30KB052 $346,174 30.96 3.34 13.16 45018.8284.61SCREENING & CRUSHING PLANTS,

CLASSIFYING PLANT (SAND SORT) 8'W X 32'L TANK & 44" DIA SCREW

HP E

METSO MINERALS

25CV 50DS30RA002 $76,671 6.79 0.74 2.64 1304.1417.34SCREENING & CRUSHING PLANTS, GRIZZLY-SINGLE SCREEN, 120 CY/HR, TRAILER MTD

HP D-off

49CV 90DS30RA003 $121,300 10.70 1.17 5.16 1956.5228.53SCREENING & CRUSHING PLANTS, GRIZZLY-SINGLE SCREEN, 200 CY/HR, TRAILER MTD

HP D-off

SNOW REMOVAL EQUIPMENTS350.00 SNOW REMOVAL EQUIPMENTSUBCATEGORY

AMERICAN ROAD MACHINERY, INC.

112S35AR001 $5,156 0.52 0.05 0.00 150.311.14SNOW REMOVAL EQUIPMENT, SNOW PLOW, REVERSIBLE (ADD DUMP TRUCK)

713S35AR002 $7,326 0.73 0.08 0.00 200.451.61SNOW REMOVAL EQUIPMENT, SNOW PLOW, 1-WAY TRIP (ADD DUMP TRUCK)

EP 1110-1-8, Vol. 430 Nov 11

2-208


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

SOIL & ROAD STABILIZERSS400.00 SOIL & ROAD STABILIZERSSUBCATEGORY


360MPH-362 R RECYCLER

S40BO002 $343,895 26.84 3.55 41.62 39016.97111.85SOIL & ROAD STABILIZER, 12" DEEP X 79" WIDE, HYDROSTATIC RECLAIMER/ SOIL STABILIZER, 4X2

HP D-off

360MPH-362 SS40BO003 $324,507 25.29 3.35 41.62 39016.00108.24SOIL & ROAD STABILIZER, 14" DEEP X 79" WIDE, HYDROSTATIC RECLAIMER/ SOIL STABILIZER, 4X2

HP D-off

360MPH-362 SDMS40BO004 $330,115 25.74 3.41 41.62 39016.28109.29SOIL & ROAD STABILIZER, 21" DEEP X 79" WIDE, HYDROSTATIC RECLAIMER/ SOIL STABILIZER, 4X2

HP D-off


309RR-250BS40CA001 $382,047 30.07 3.94 35.72 37018.98112.55SOIL & ROAD STABILIZER, 12" DEEP X 96" WIDE, HYDROSTATIC RECLAIMER/ SOIL STABILIZER, 4X2

HP D-off

309SS-250BS40CA002 $366,463 28.49 3.78 35.72 30818.03109.02SOIL & ROAD STABILIZER, 18" DEEP X 96" WIDE, HYDROSTATIC RECLAIMER/ SOIL STABILIZER, 4X2

HP D-off

350RM-300S40CA003 $318,943 23.13 3.29 40.46 51814.86113.93SOIL & ROAD STABILIZER, 18" DEEP X 96" WIDE, HYDROSTATIC ROAD RECLAIMER/ SOIL STABILIZER, 4X4

HP D-off

540RM-500S40CA004 $499,304 38.00 5.15 62.42 59924.15169.56SOIL & ROAD STABILIZER, 16" DEEP X 96" WIDE, HYDROSTATIC ROAD RECLAIMER/ SOIL STABILIZER, 4X4

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-209


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

SPLITTERS, ROCK & CONCRETES450.00 SPLITTERS, ROCK & CONCRETESUBCATEGORY

ELCO INTERNATIONAL INC.

8002-2S45DA004 $12,947 1.73 0.14 0.00 11.014.49SPLITTER, ROCK & CONCRETE, 220 TON SFORCE, 1.75" DIA, SIZE 2, 5 GAL, 12" DEEP HOLE REQ'D (ADD 80 CFM COMPRESSOR)

CFM A


CFM A


CFM A

TRACTOR BLADES & ATTACHMENTS (including agricultural)T100.00 TRACTOR BLADES & ATTACHMENTS (including agricultural)SUBCATEGORY


D3-61-9722T10CA001 $14,066 1.13 0.15 0.00 220.722.59TRACTOR ATTACHMENTS, BLADE, POWER ANGLE, HYDRAULIC, FOR D3, 1.65 CY (ADD D3 TRACTOR)

D3-PA 30BT10CA002 $21,097 1.69 0.22 0.00 211.073.83TRACTOR ATTACHMENTS, POWER WINCH, W/250' CABLE, FOR D3 (ADD D3 TRACTOR)


EP 1110-1-8, Vol. 430 Nov 11

2-210


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

T10 CATERPILLAR INC. ( MACHINE DIVISION) (continued)

D4-PA 30BT10CA005 $21,097 1.69 0.22 0.00 211.073.83TRACTOR ATTACHMENTS, POWER WINCH, W/250' CABLE, FOR D4 (ADD D4 TRACTOR)

D5 N - ANGLE BLADE

T10CA007 $23,567 1.89 0.24 0.00 261.194.27TRACTOR ATTACHMENTS, BLADE, POWER ANGLE, HYDRAULIC, FOR D5, 2.53 CY (ADD D5 TRACTOR)

D5-PA 55T10CA008 $31,496 2.52 0.32 0.00 261.585.67TRACTOR ATTACHMENTS, POWER WINCH, FOR D5 (ADD D5 TRACTOR)

D6-108-3970T10CA009 $28,760 2.30 0.30 0.00 571.455.19TRACTOR ATTACHMENTS, BLADE, STRAIGHT, HYDRAULIC, FOR D6, 5.09 CY (ADD D6 TRACTOR)


D6-PA56 WINCHT10CA011 $43,863 3.51 0.45 0.00 272.217.87TRACTOR ATTACHMENTS, POWER WINCH, W/CABLE, FOR D6 (ADD D6 TRACTOR)

D7-ST10CA012 $42,361 3.39 0.44 0.00 772.147.61TRACTOR ATTACHMENTS, BLADE, STRAIGHT, HYDRAULIC, FOR D7, 6.75 CY (ADD D7 TRACTOR)

D7-UT10CA013 $46,518 3.72 0.48 0.00 862.348.34TRACTOR ATTACHMENTS, BLADE, UNIVERSAL, HYDRAULIC, FOR D7, 10.09 CY (ADD D7 TRACTOR)

D7-AT10CA014 $38,700 3.10 0.40 0.00 781.956.96TRACTOR ATTACHMENTS, BLADE, POWER ANGLE, HYDRAULIC, FOR D7, 5.08 CY (ADD D7 TRACTOR)

D7-PA57 WINCHT10CA015 $57,665 4.61 0.59 0.00 452.9010.33TRACTOR ATTACHMENTS, POWER WINCH, W/CABLE, FOR D7 (ADD D7 TRACTOR)

EP 1110-1-8, Vol. 430 Nov 11

2-211


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)


D8-SUT10CA016 $56,423 4.51 0.58 0.00 1072.8410.14TRACTOR ATTACHMENTS, BLADE, STRAIGHT, HYDRAULIC, FOR D8, 6.09 CY (ADD D8 TRACTOR)


D8-AT10CA018 $54,171 4.33 0.56 0.00 1232.739.75TRACTOR ATTACHMENTS, BLADE, POWER ANGLE, HYDRAULIC, FOR D8, 6.09 CY (ADD D8 TRACTOR)

D8-PPT10CA019 $1,558 0.12 0.02 0.00 50.080.33TRACTOR ATTACHMENTS, BLADE, PUSH PLATE, FOR D8 (ADD D8 TRACTOR)

D8, PA58VS WINCH

T10CA020 $57,470 4.60 0.59 0.00 502.8910.36TRACTOR ATTACHMENTS, POWER WINCH, W/CABLE, FOR D8 (ADD D8 TRACTOR)

D9-SUT10CA021 $76,658 6.13 0.79 0.00 1433.8613.80TRACTOR ATTACHMENTS, BLADE, SEMI-U, HYDRAULIC, FOR D9, 17.70 CY (ADD D9 TRACTOR)


D9, PA59VS WINCH

T10CA023 $77,274 6.18 0.80 0.00 863.8913.93TRACTOR ATTACHMENTS, POWER WINCH, W/CABLE, FOR D9 (ADD D9 TRACTOR)

D10-SU ABRASION

T10CA024 $114,322 9.15 1.18 0.00 3575.7620.59TRACTOR ATTACHMENTS, BLADE, SEMI-U, HYDRAULIC, FOR D10, 24.20 CY (ADD D10 TRACTOR)

D10-U ABRASION

T10CA025 $121,640 9.73 1.26 0.00 2516.1321.90TRACTOR ATTACHMENTS, BLADE, UNIVERSAL, HYDRAULIC, FOR D10, 28.70 CY (ADD D10 TRACTOR)

EP 1110-1-8, Vol. 430 Nov 11

2-212


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT


D11-SUT10CA026 $165,947 13.28 1.71 0.00 3678.3529.88TRACTOR ATTACHMENTS, BLADE, STRAIGHT, HYDRAULIC, FOR D11, 35.50 CY (ADD D11 TRACTOR)


DEERE & COMPANY

915 V-RIPPERT10JD001 $13,944 1.06 0.14 0.00 170.672.75TRACTOR ATTACHMENTS, DEEP TILLER, 5x7 V SHAPED, 175" WIDE, 7 SHANKS (ADD 200HP TRACTOR W/PTO)

TRACTORS, CRAWLER (DOZER) (includes blade)T150.01 0 THRU 225 HPSUBCATEGORY


70D-3G LGPT15CA002 $97,940 6.86 1.08 8.09 1754.5129.07TRACTOR, CRAWLER (DOZER), 70 HP, LOW GROUND PRESSURE, W/2.0 CY SEMI-U BLADE (ADD ATTACHMENTS)

HP D-off

80D-4G XLT15CA020 $123,532 8.65 1.36 9.25 1815.6935.55TRACTOR, CRAWLER (DOZER), 80 HP, POWERSHIFT, W/2.18 CY SEMI-U BLADE (ADD ATTACHMENTS)

HP D-off

80D-4G LGPT15CA005 $121,028 8.47 1.33 9.25 1845.5735.04TRACTOR, CRAWLER (DOZER), 80 HP, LOW GROUND PRESSURE, W/2.39 CY SEMI-U BLADE (ADD ATTACHMENTS)

HP D-off

90D-5G XLT15CA021 $127,871 8.95 1.41 10.40 1955.8937.75TRACTOR, CRAWLER (DOZER), 90 HP, POWERSHIFT, W/2.85 CY POWER ANGLE BLADE (ADD ATTACHMENTS)

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-213


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)


90D-5G LGPT15CA022 $135,390 9.48 1.49 10.40 2036.2339.27TRACTOR, CRAWLER (DOZER), 90 HP, LOW GROUND PRESSURE, W/3.04 CY POWER ANGLE BLADE (ADD ATTACHMENTS)

HP D-off

110D-5M XLT15CA024 $172,998 12.11 1.91 12.72 2777.9749.52TRACTOR, CRAWLER (DOZER), 110 HP, POWERSHIFT, W/3.37 CY SEMI-U BLADE (ADD ATTACHMENTS)

HP D-off

145D-6N PS XL FTCT15CA008 $241,517 16.91 2.66 16.76 32111.1267.98TRACTOR, CRAWLER (DOZER), 145 HP, POWERSHIFT, W/5.60 CY SEMI-U BLADE (ADD ATTACHMENTS)

HP D-off

165D-6RT15CA023 $346,077 24.23 3.81 19.07 51915.9391.67TRACTOR, CRAWLER (DOZER), 165 HP, LOW GROUND PRESSURE, POWERSHIFT, W/5.09 CY SEMI-U BLADE (ADD ATTACHMENTS)

HP D-off

165D-6R WHAT15CA009 $346,077 24.23 3.81 19.07 51915.9391.67TRACTOR, CRAWLER (DOZER), 165 HP, W/14.3 CY BLADE, TRASH/WASTE HANDLING ARRANGEMENT

HP D-off

185D-6R LGPT15CA011 $336,761 23.57 3.71 21.39 46115.5092.48TRACTOR, CRAWLER (DOZER), 165 HP, LOW GROUND PRESSURE, W/5.09 CY SEMI-U BLADE (ADD ATTACHMENTS)

HP D-off

CASE CORPORATION

67550H WTT15CS004 $110,258 7.72 1.21 7.75 1465.0731.14TRACTOR, CRAWLER (DOZER), 67 HP, POWERSHIFT, W/1.90 CY UNIVERSAL BLADE (ADD ATTACHMENTS)

HP D-off

1191150H WTT15CS007 $192,433 13.47 2.12 13.76 2638.8654.63TRACTOR, CRAWLER (DOZER), 119 HP, POWERSHIFT, W/3.90 CY UNIVERSAL BLADE (ADD ATTACHMENTS)

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-214


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

DEERE & COMPANY

70450H LTT15JD005 $88,161 6.17 0.97 8.09 1554.0627.10TRACTOR, CRAWLER (DOZER), 70 HP, POWERSHIFT, W/2.00 CY ANGLE BLADE (ADD ATTACHMENTS)

HP D-off

74450H LGPT15JD006 $104,858 7.34 1.16 8.55 1654.8330.99TRACTOR, CRAWLER (DOZER), 74 HP, LOW GROUND PRESSURE, W/2.15 CY ANGLE BLADE (ADD ATTACHMENTS)

HP D-off

90650HT15JD007 $120,477 8.43 1.33 10.40 1855.5536.27TRACTOR, CRAWLER (DOZER), 90 HP, POWERSHIFT, W/2.60 CY ANGLE BLADE (ADD ATTACHMENTS)

HP D-off

140750C-II LTT15JD008 $212,889 14.90 2.35 16.18 3179.8061.55TRACTOR, CRAWLER (DOZER), 140 HP, POWERSHIFT, W/5.60 CY ANGLE BLADE (ADD ATTACHMENTS)

HP D-off

140750C-II LGPT15JD009 $223,997 15.68 2.47 16.18 36510.3163.78TRACTOR, CRAWLER (DOZER), 140 HP, LOW GROUND PRESSURE, W/4.84 CY ANGLE BLADE (ADD ATTACHMENTS)

HP D-off

185850CT15JD010 $277,740 19.44 3.06 21.39 40412.7880.62TRACTOR, CRAWLER (DOZER), 185 HP, POWERSHIFT, W/7.44 CY SEMI-U BLADE (ADD ATTACHMENTS)

HP D-off

185850C LGPT15JD011 $300,658 21.05 3.31 21.39 42013.8485.23TRACTOR, CRAWLER (DOZER), 185 HP, LOW GROUND PRESSURE, W/7.14 CY SEMI-U BLADE (ADD ATTACHMENTS)

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-215


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

0.02 226 HP THRU 425 HPSUBCATEGORY


240D-7R SERIES IIT15CA012 $401,343 24.08 4.22 27.74 56316.26101.50TRACTOR, CRAWLER (DOZER), 240 HP, POWERSHIFT, W/8.98 CY SEMI-U BLADE (ADD ATTACHMENTS)

HP D-off

240D-7R II LGPT15CA014 $475,876 28.55 5.01 27.74 53019.29114.56TRACTOR, CRAWLER (DOZER), 240 HP, LOW GROUND PRESSURE, W/7.70 CY STRAIGHT BLADE (ADD ATTACHMENTS)

HP D-off

310D-8R IIT15CA016 $525,046 31.50 5.53 35.84 89821.28132.29TRACTOR, CRAWLER (DOZER), 310 HP, POWERSHIFT, W/15.3 CY SEMI-U BLADE (ADD ATTACHMENTS)

HP D-off

410D-9RT15CA017 $698,551 41.91 7.35 47.40 1,03328.31175.68TRACTOR, CRAWLER (DOZER), 410 HP, POWERSHIFT, W/17.7 CY SEMI-U BLADE (ADD ATTACHMENTS)

HP D-off


310D155AX-6T15KM008 $548,947 32.94 5.78 35.84 80322.25136.49TRACTOR, CRAWLER (DOZER), 310 HP, POWERSHIFT, W/11.5 CY SEMI-U BLADE

HP D-off

0.03 OVER 425 HPSUBCATEGORY


580D-10RT15CA018 $992,384 52.93 9.99 57.19 1,42136.46210.64TRACTOR, CRAWLER (DOZER), 580 HP, POWERSHIFT, W/28.7 CY SEMI-U BLADE (ADD ATTACHMENTS)

HP D-off

850D-11RT15CA019 $1,541,144 82.19 15.51 83.81 2,02956.61321.75TRACTOR, CRAWLER (DOZER), 850 HP, POWERSHIFT, W/44.0 CY SEMI-U BLADE (ADD ATTACHMENTS)

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-216


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

TRACTORS, WHEEL TYPE (DOZER)T200.00 TRACTORS, WHEEL TYPE (DOZER)SUBCATEGORY


240814-FT20CA001 $382,682 22.36 3.72 23.66 47914.9076.78TRACTOR, WHEEL (DOZER), 240 HP, ARTICULATING, 4X4, W/3.77 CY STRAIGHT BLADE

HP D-off

339824-G IIT20CA002 $557,367 32.12 5.42 33.43 63321.48113.31TRACTOR, WHEEL (DOZER), 339 HP, ARTICULATING, 4X4, W/6.70 CY STRAIGHT BLADE

HP D-off

481834-GT20CA003 $835,069 46.67 8.13 47.43 90231.47164.41TRACTOR, WHEEL (DOZER), 481 HP, ARTICULATING, 4X4, W/10.33 CY STRAIGHT BLADE

HP D-off

TRACTORS, AGRICULTURALT250.10 CRAWLERSUBCATEGORY


267CH 65ET25CA006 $221,312 18.81 2.21 28.14 33111.6273.27TRACTOR, AGRICULTURAL, CRAWLER-RUBBER TRACK, 267 HP, 3 POINT HITCH

HP D-off


HP D-off


HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-217


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

0.20 WHEELSUBCATEGORY

DEERE & COMPANY

455103T25JD015 $19,650 1.85 0.20 4.74 391.139.61TRACTOR, AGRICULTURAL, WHEEL, 45 HP, 4X2, PTO, 3 POINT HITCH

HP D-off


HP D-off

565225 W/609 MOWER

T25JD017 $32,786 3.24 0.33 5.90 511.9513.69TRACTOR, AGRICULTURAL, WHEEL, 56 HP, 4X2, PTO, 3 POINT HITCH, WITH 60" HEAVY DUTY ROTARY MOWER

HP D-off


HP D-off


HP D-off


HP D-off


HP D-off


HP D-off


HP D-off


HP D-off


HP D-off


HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-218


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

TRENCHERS, CHAIN TYPE CUTTERT300.00 TRENCHERS, CHAIN TYPE CUTTERSUBCATEGORY

DITCH WITCH(The Charles Machine Works)I

16RT12T30DW012 $9,349 0.93 0.10 3.41 100.576.01TRENCHER, CHAIN TYPE CUTTER, 36" DEEP X 10" WIDE, WALK BEHIND

HP G

22RT24T30DW013 $12,228 1.16 0.13 4.69 110.718.14TRENCHER, CHAIN TYPE CUTTER, 48" DEEP X 8" WIDE, WALK BEHIND

HP G

102RT115T30DW014 $126,195 12.35 1.33 10.75 807.5141.65TRENCHER, CHAIN TYPE CUTTER, 96" DEEP X 16" WIDE, 4X4 (W/BLADE, BHOE)

HP D-off

42RT45T30DW005 $37,696 3.61 0.40 4.43 422.2113.83TRENCHER, CHAIN TYPE CUTTER, 63" DEEP X 12" WIDE, 4X4 (W/DBL PIVOT & H313 TRENCHER)

HP D-off

60RT55T30DW016 $67,409 6.59 0.71 6.32 954.0122.90TRENCHER, CHAIN TYPE CUTTER, 62" DEEP X 12" WIDE, 4X4 (W/BLADE)

HP D-off

78RT80T30DW017 $80,501 7.78 0.85 8.22 694.7428.12TRENCHER, CHAIN TYPE CUTTER, 62" DEEP X 12" WIDE, 4X4 (W/BLADE)

HP D-off

99RT95MT30DW018 $107,997 10.53 1.14 10.43 776.4137.03TRENCHER, CHAIN TYPE CUTTER, 96" DEEP X 24" WIDE, 4X4 (W/BLADE)

HP D-off

220HT220T30DW011 $518,539 51.85 5.46 23.19 43031.39147.34TRENCHER, CHAIN TYPE CUTTER, 96" DEEP X 12"-24" WIDE, CRAWLER (W/BLADE)

HP D-off

TESMEC USA, INC.

220TRS 775T30TM007 $480,913 48.09 5.06 23.19 45029.11138.54TRENCHER, CHAIN TYPE CUTTER, 4' DEEP X 12" WIDE, CRAWLER (W/CRUMBSHOE) SELF LEVEL, OFFSET

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-219


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

T30 TESMEC USA, INC. (continued)220TRS 775T30TM008 $484,089 48.41 5.09 23.19 47029.30139.28TRENCHER, CHAIN TYPE CUTTER, 6'

DEEP X 18" WIDE, CRAWLER (W/CRUMBSHOE) SELF LEVEL, OFFSET

HP D-off

385TRS 1100T30TM012 $821,802 82.18 8.65 40.58 85049.74237.81TRENCHER, CHAIN TYPE CUTTER, 8' DEEP X 26" WIDE, CRAWLER (W/CRUMBSHOE)

HP D-off

525TRS 1475 XHPT30TM014 $1,288,262 128.83 13.56 55.34 1,68077.98363.51TRENCHER, CHAIN TYPE CUTTER, 10' DEEP X 26" WIDE, CRAWLER (W/CRUMBSHOE)

HP D-off


HP D-off


HP D-off


125T 455T30VE007 $190,115 19.01 2.00 13.18 18011.5159.28TRENCHER, CHAIN TYPE CUTTER, 6' DEEP X 8"-24" WIDE, CRAWLER, HYDROSTATIC

HP D-off

185T 555 IIIT30VE008 $241,569 24.16 2.54 19.50 22514.6278.41TRENCHER, CHAIN TYPE CUTTER, 8' DEEP X 8"-24" WIDE, CRAWLER, HYDROSTATIC

HP D-off

250T 655 IIIT30VE009 $391,730 39.17 4.12 26.35 50023.71121.23TRENCHER, CHAIN TYPE CUTTER, 8' DEEP X 10.5"-26" WIDE, CRAWLER, HYDROSTATIC

HP D-off

275T 755 IIIT30VE010 $475,086 47.51 5.00 28.99 66028.76143.69TRENCHER, CHAIN TYPE CUTTER, 10' DEEP X 14"-36" WIDE, CRAWLER, HYDROSTATIC

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-220


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

TRENCHERS, WHEEL TYPE CUTTERT350.00 TRENCHERS, WHEEL TYPE CUTTERSUBCATEGORY

CLEVELAND TRENCHER

1409624T35CT001 $252,441 25.24 2.66 14.76 17015.2875.62TRENCHER, WHEEL TYPE CUTTER, 72" DEEP X 21.5" WIDE, ROUND BUCKET, CRAWLER

HP D-off

1409600-ST35CT002 $310,892 31.09 3.27 14.76 22818.8289.30TRENCHER, WHEEL TYPE CUTTER, 72" DEEP X 24" WIDE, ROUND BUCKET, CRAWLER

HP D-off

185246-FDT35CT003 $349,352 34.94 3.68 19.50 32021.15103.63TRENCHER, WHEEL TYPE CUTTER, 84" DEEP X 24" WIDE, ROUND BUCKET, CRAWLER

HP D-off

1027036T35CT005 $311,163 31.12 3.27 10.75 26318.8384.86TRENCHER, WHEEL TYPE CUTTER, 84" DEEP X 36" WIDE, ROUND BUCKET, CRAWLER

HP D-off


HP D-off

1027036-HDT35CT004 $328,953 32.90 3.46 10.75 28619.9189.02TRENCHER, WHEEL TYPE CUTTER, 84" DEEP X 36" WIDE, ROUND BUCKET, CRAWLER

HP D-off

1027036-SDT35CT007 $344,434 34.44 3.62 10.75 34020.8492.63TRENCHER, WHEEL TYPE CUTTER, 84" DEEP X 36" WIDE, ROUND BUCKET, CRAWLER

HP D-off


HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-221


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

T35 CLEVELAND TRENCHER (continued)1507648-SDT35CT009 $513,740 51.37 5.41 15.81 44531.10137.92TRENCHER, WHEEL TYPE CUTTER, 90"

DEEP X 48" WIDE, ROUND BUCKET, CRAWLER

HP D-off


HP D-off

175400W-HDT35CT011 $604,410 60.44 6.36 18.45 70036.58162.10TRENCHER, WHEEL TYPE CUTTER, 108" DEEP X 72" WIDE, ROUND BUCKET, CRAWLER

HP D-off

TRUCK OPTIONST400.10 CRANES / HOISTS, PERSONNEL & MATERIAL HANDLINGSUBCATEGORY

AUTO CRANE CO.

AC8-59T40AH001 $28,123 2.81 0.30 0.00 21.716.45TRUCK OPTIONS, CRANE, HYDRAULIC, 3-ARM ARTICULATING, 3.5 TON, 32' BOOM (ADD 21,000 GVW TRUCK & FLATBED)



EP 1110-1-8, Vol. 430 Nov 11

2-222


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

PALFINGER INC.

PC 2700T40PA001 $7,378 0.74 0.08 0.00 90.451.87TRUCK OPTIONS, CRANE, HYDRAULIC, 2-ARM ARTICULATING, 2.4 TON, 21' BOOM (ADD 25,000 GVW TRUCK & FLATBED)

PK 14002-EHT40PA002 $40,642 4.06 0.43 0.00 352.469.20TRUCK OPTIONS, CRANE, HYDRAULIC, 3-ARM ARTICULATING, 6.2 TON, 62' BOOM (ADD 28,000 GVW TRUCK & FLATBED)

PK 20002T40PA003 $47,909 4.79 0.50 0.00 512.9010.81TRUCK OPTIONS, CRANE, HYDRAULIC, 3-ARM ARTICULATING, 8.3 TON, 70' BOOM (ADD 30,000 GVW TRUCK & FLATBED)

PK 30002T40PA004 $52,525 5.25 0.55 0.00 613.1811.83TRUCK OPTIONS, CRANE, HYDRAULIC, 3-ARM ARTICULATING, 10 TON, 69' BOOM (ADD 52,000 GVW TRUCK & FLATBED)

PK 50002-EHT40PA005 $93,240 9.32 0.98 0.00 1,0725.6420.81TRUCK OPTIONS, CRANE, HYDRAULIC, 2-ARM ARTICULATING, 12.5 TON, 82' BOOM (ADD 60,000 GVW TRUCK & FLATBED)

PK 65002-SHT40PA006 $111,368 11.14 1.17 0.00 1266.7424.82TRUCK OPTIONS, CRANE, HYDRAULIC, 2-ARM ARTICULATING, 22 TON, 82' BOOM (ADD 62,000 GVW TRUCK & FLATBED)

0.20 DUMP BODY, REARSUBCATEGORY

GALION DUMP BODIES, INC.

PACKAGE 89-FT40GN001 $16,295 1.83 0.16 0.00 421.083.56TRUCK OPTIONS, DUMP BODY, REAR, 16-23.5 CY (W/HOIST) (ADD 36,000 GVW TRUCK)

EP 1110-1-8, Vol. 430 Nov 11

2-223


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

MIDLAND MANUFACTURING INC.

KLEENSIDET40MY002 $5,413 0.61 0.05 0.00 210.361.18TRUCK OPTIONS, DUMP BODY, REAR, 7.5 CY, AIR GATE (W/HOIST) (ADD 30,000 GVW TRUCK)





0.30 FLATBEDS, WITH SIDESSUBCATEGORY

KNAPHEIDE MANUFACTURING CO.

8' VALUE MASTER PLAT

T40KF011 $4,624 0.46 0.05 0.00 110.280.89TRUCK OPTIONS, FLATBED, W/40" SIDE RACKS, 8' X 8'

10' VALUE MASTER PLA


12' VALUE MASTER


16' VALUE MASTER


20' VALUE MASTER


EP 1110-1-8, Vol. 430 Nov 11

2-224


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

T40 KNAPHEIDE MANUFACTURING CO. (continued)

24' VALUE MASTER


0.41 HOIST, ELECTRIC DRIVESUBCATEGORY

KNAPHEIDE MANUFACTURING CO.

KH-1416LT40KF021 $4,580 0.46 0.05 0.00 60.281.05TRUCK OPTIONS, HOIST, ELECTRIC DRIVE, PTO, 10' TO 14', 7-16 TON

KH-1416-EET40KF023 $3,321 0.33 0.03 0.00 60.200.73TRUCK OPTIONS, HOIST, ELECTRIC DRIVE, 10' TO 14', 7-16 TON

KH-1627L-EET40KF024 $4,823 0.48 0.05 0.00 100.291.04TRUCK OPTIONS, HOIST, ELECTRIC DRIVE, 15' TO 20', 14-37 TON

KH-2538LT40KF022 $8,207 0.82 0.09 0.00 150.501.80TRUCK OPTIONS, HOIST, ELECTRIC DRIVE, PTO, 20' TO 24', 20-45 TON

0.50 TRANSIT MIXERSSUBCATEGORY


235RDTM-8T40XX034 $154,192 16.38 1.57 28.41 2669.7665.19TRANSIT MIXER, 8 CY, HYDROSTATIC, 100 GAL, (INCLUDES 60,000 GVW TRUCK)

HP D-on


HP D-on


HP D-on

EP 1110-1-8, Vol. 430 Nov 11

2-225


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

T40 NO SPECIFIC MANUFACTURER (continued)285RDTM-11T40XX037 $184,448 19.60 1.88 34.46 28511.6878.53TRANSIT MIXER, 11 CY, HYDROSTATIC,

100 GAL, (INCLUDES 70,000 GVW TRUCK)

HP D-on


HP D-on

0.60 WATER TANKSSUBCATEGORY


DS 2000T40RS001 $30,415 2.85 0.33 0.00 381.765.69TRUCK OPTIONS, WATER TANK, 2,000 GAL (ADD 28,000 GVW TRUCK)



0.70 ALL OTHER OPTIONSSUBCATEGORY

ARROW-MASTER, INC.

801350TT40AG001 $89,886 8.75 0.95 8.43 1005.3328.24TRUCK OPTIONS, GUILLOTINE CONCRETE BREAKER, W/8'' DIA BREAKING TOOL AND CAB

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-226


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

TRUCK TRAILERST450.10 BOTTOM DUMPSUBCATEGORY


40' MC 2000T45MY004 $32,588 2.50 0.31 0.00 1521.566.59TRUCK TRAILER, BOTTOM DUMP, 21 CY, 28 TON, 40' - 2 AXLE, CLAMSHELL (ADD TOWING TRUCK)

40' TC 3000T45MY005 $43,994 3.31 0.42 0.00 1382.088.86TRUCK TRAILER, BOTTOM DUMP, 21 CY, 30 TON, 40' - 3 AXLE, CLAMSHELL (ADD TOWING TRUCK)




T45XX001 $40,235 3.27 0.39 0.00 1222.037.94TRUCK TRAILER, BOTTOM DUMP, 27 TON (ADD TOWING TRUCK)

T45XX003 $53,819 4.50 0.52 0.00 1602.7710.34TRUCK TRAILER, BOTTOM DUMP, 30 TON (ADD TOWING TRUCK)

0.20 END DUMPSUBCATEGORY


28' SK2000T45MY015 $34,841 2.70 0.34 0.00 1151.696.93TRUCK TRAILER, END DUMP, 28 CY, 36 TON, 28' - 2 AXLE (W/HOIST) (ADD TOWING TRUCK)

EP 1110-1-8, Vol. 430 Nov 11

2-227


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

T45 MIDLAND MANUFACTURING INC. (continued)

32' ST 2400T45MY016 $35,509 2.76 0.34 0.00 1301.727.04TRUCK TRAILER, END DUMP, 28 CY, 36 TON, 32' - 2 AXLE (W/HOIST) (ADD TOWING TRUCK)

39' SK 2300T45MY017 $39,383 2.90 0.38 0.00 1701.837.98TRUCK TRAILER, END DUMP, 39 CY, 50 TON, 39' - 3 AXLE (W/HOIST) (ADD TOWING TRUCK)


T45XX008 $33,817 2.70 0.33 0.00 1101.686.65TRUCK TRAILER, END DUMP, 20 CY, 24 TON (ADD TOWING TRUCK)

0.30 PUP TRAILERSUBCATEGORY


14' SK 2100T45MY018 $23,441 2.10 0.23 0.00 801.285.61TRUCK TRAILER, PUP TRAILER, 10 CY, 13 TON, 14' - 2 AXLE (W/HOIST) (ADD TOWING TRUCK)

14' SL 2100T45MY019 $23,253 2.08 0.23 0.00 801.275.58TRUCK TRAILER, PUP TRAILER, 12 CY, 15 TON, 14' - 2 AXLE (W/HOIST) (ADD TOWING TRUCK)


T45XX009 $34,355 3.43 0.34 0.00 862.067.76TRUCK TRAILER, PUP TRAILER, 8 CY, LONG TONGUE (ADD TOWING TRUCK)

T45XX010 $34,471 3.44 0.34 0.00 862.067.78TRUCK TRAILER, PUP TRAILER, 10 CY, LONG TONGUE (ADD TOWING TRUCK)

EP 1110-1-8, Vol. 430 Nov 11

2-228


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

T45 NO SPECIFIC MANUFACTURER (continued)T45XX032 $43,186 4.53 0.43 0.00 922.709.59TRUCK TRAILER, PUP TRAILER, 13 CY,

14.5 TON, 3 AXLE (ADD TOWING TRUCK)

T45XX033 $50,877 5.29 0.50 0.00 1003.1511.34TRUCK TRAILER, PUP TRAILER, 16 CY, 18.0 TON, 4 AXLE (ADD TOWING TRUCK)

0.41 LOWBOY, RIGID NECK, DROP DECKSUBCATEGORY

EAGER BEAVER

35GSL-BRT45EA006 $47,067 3.63 0.45 0.00 1712.278.66TRUCK TRAILER, LOWBOY, 35 TON, 2 AXLE, DETATCHABLE GOOSENECK (ADD TOWING TRUCK)

1350GSL/3T45EA007 $63,522 4.81 0.61 0.00 2053.0211.65TRUCK TRAILER, LOWBOY, 50 TON, 3 AXLE , DETATCHABLE GOOSENECK (ADD TOWING TRUCK)

HP


T45XX011 $34,033 2.76 0.33 0.00 951.716.11TRUCK TRAILER, LOWBOY, 25 TON, 2 AXLE (ADD TOWING TRUCK)






EP 1110-1-8, Vol. 430 Nov 11

2-229


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

T45 NO SPECIFIC MANUFACTURER (continued)T45XX017 $56,396 4.47 0.54 0.00 1752.7810.10TRUCK TRAILER, LOWBOY, 60 TON, 3

AXLE (ADD TOWING TRUCK) T45XX018 $56,936 4.52 0.55 0.00 2132.8110.19TRUCK TRAILER, LOWBOY, 70 TON, 3






AXLE (ADD TOWING TRUCK)

0.50 FLATBED TRAILERSUBCATEGORY


T45XX025 $32,276 2.56 0.31 0.00 1101.595.60TRUCK TRAILER, FLATBED, 25 TON, 2 AXLE (ADD TOWING TRUCK)

32T45XX034 $31,705 2.51 0.31 0.00 1031.575.82TRUCK TRAILER, FLATBED, 40 TON, 2 AXLE (ADD TOWING TRUCK)

40T45XX035 $33,698 2.69 0.32 0.00 1101.676.12TRUCK TRAILER, FLATBED, 40 TON, 2 AXLE (ADD TOWING TRUCK)

EP 1110-1-8, Vol. 430 Nov 11

2-230


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

0.60 MISCELLANEOUS / UTILITYSUBCATEGORY


T45XX026 $18,254 1.46 0.18 0.00 620.913.48TRUCK TRAILER, MISCELLANEOUS/UTILITY, TILT BED, 12 TON, 2 AXLE (ADD TOWING TRUCK)



T45XX024 $29,801 2.33 0.29 0.00 621.465.21TRUCK TRAILER, MISCELLANEOUS/UTILITY, ATTACHMENT, HELPER DOLLY, 60 TON TRAILER MAX (ADD TOWING TRUCK)

0.70 WATER TANKER TRAILERSUBCATEGORY


63T45XX029 $84,216 6.14 0.90 6.64 1703.9720.34TRUCK TRAILER, WATER TANKER, 4,000 GAL, W/PUMP (ADD TOWING TRUCK)

HP D-off


HP D-off


HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-231


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

0.90 TANK TRAILERSSUBCATEGORY

GRACO, INC.

7528' GOOSENECK

T45G1001 $107,189 8.04 1.14 7.91 1605.1626.17TRAILER, FOAM SPRAY RIG, 40 KW GENERATOR, AIR COMPESSOR, 410' HOSE, ETC.

HP D-off

TRUCKS, HIGHWAY (Add attachments as required)T500.01 0 THRU 10,000 GVWSUBCATEGORY

GMC AND CHEVROLET

120S10 T50GM001 $17,113 1.63 0.18 6.06 261.0010.49TRUCK, HIGHWAY, 3,500 GVW, 4X2 (COMPACT)

HP G

285R26T50GM004 $38,062 3.73 0.40 14.40 502.2724.26TRUCK, HIGHWAY, 8,600 GVW, 4X2 (SUBURBAN)

HP G

285V26T50GM005 $40,918 4.01 0.43 14.40 522.4424.86TRUCK, HIGHWAY, 8,600 GVW, 4X4 (SUBURBAN)

HP G


1304X2 1/2 130 CONV GAS

T50XX001 $16,630 1.55 0.18 6.57 450.9611.01TRUCK, HIGHWAY, CONVENTIONAL, 1/2 TON PICKUP, 4X2

HP G

1304X2 3/4 130 CONV GAS


HP G

1804X2 1 180 CONV GAS

T50XX003 $22,557 2.17 0.24 9.10 411.3315.05TRUCK, HIGHWAY, CONVENTIONAL, 1 TON PICKUP, 4X2

HP G

1304X4 1/2 130 CONV GAS


HP G

1304X4 3/4 130 CONV GAS


HP G

EP 1110-1-8, Vol. 430 Nov 11

2-232


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

T50 NO SPECIFIC MANUFACTURER (continued)1804X4 1 180

CONV GAST50XX006 $24,167 2.33 0.25 9.10 411.4215.40TRUCK, HIGHWAY, CONVENTIONAL, 1

TON PICKUP, 4X4 HP G

1304X2 1/2 130 CREW GAS

T50XX007 $17,548 1.64 0.18 6.57 451.0011.19TRUCK, HIGHWAY, CREW, 1/2 TON PICKUP, 4X2

HP G

1304X2 3/4 130 CREW GAS


HP G

1804X2 1 180 CREW GAS

T50XX009 $25,831 2.50 0.27 9.10 451.5215.73TRUCK, HIGHWAY, CREW, 1 TON PICKUP, 4X2

HP G

1304X4 1/2 130 CREW GAS


HP G

1804X4 3/4 180 CREW GAS


HP G

1804X4 1 180 CREW GAS


HP G

754X2 1/2 75 CONV DSL


HP D-on

754X2 3/4 75 CONV DSL


HP D-on

1304X2 1 130 CONV DSL


HP D-on

1304X4 1/2 130 CONV DSL


HP D-on

1304X4 3/4 130 CONV DSL


HP D-on

130CONV DSL 4X4 1 130


HP D-on

1304X2 3/4 130 CREW DSL


HP D-on

EP 1110-1-8, Vol. 430 Nov 11

2-233


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

T50 NO SPECIFIC MANUFACTURER (continued)1304X4 3/4 130

CREW DSLT50XX020 $29,853 2.91 0.31 3.55 551.7710.28TRUCK, HIGHWAY, CREW, 3/4 TON

PICKUP 4X4 HP D-on

1304X2 1 130 CREW DSL


HP D-on

0.02 OVER 10,000 THRU 30,000 GVW (Chassis only - Add options)SUBCATEGORY


2104X2 20KGVW GAS

T50XX023 $42,544 3.25 0.44 24.26 702.0734.67TRUCK, HIGHWAY, 20,000 LBS GVW, 2 AXLE, 4X2 (CHASSIS ONLY-ADD OPTIONS)

HP G

2104X2 25KGVW GAS


HP G

1804X2 25KGVW DSL


HP D-on

1704X4 30KGVW DSL


HP D-on

2104X2 30KGVW DSL


HP D-on

2104X2 30KGVW DSL

T50XX035 $100,255 7.78 1.03 13.92 1354.9232.29TRUCK, HIGHWAY, 30,000 LBS GVW, 2 AXLE, 4X2, WITH 3-ARM ARTICULATING CRANE, 3.5 TON, 32' BOOM, WITH 8' X 20' FLATBED

HP D-on

EP 1110-1-8, Vol. 430 Nov 11

2-234


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

0.03 OVER 30,000 GVW (Chassis only - Add options)SUBCATEGORY


2654X2 35KGVW DSL


HP D-on

2654X2 35KGVW DSL

T50XX032 $124,435 8.10 1.27 24.80 1605.3245.44DUMP TRUCK, HIGHWAY, 35,000 LBS GVW, 2 AXLE, 4X2 WITH REAR 10 - 13 CY DUMP BODY

HP D-on

2306X4 45KGVW DSL


HP D-on

3106X4 55KGVW DSL


HP D-on

3506X6 70KGVW DSL


HP D-on

4006X4 75KGVW DSL


HP D-on

4006X4 75KGVW DSL

T50XX033 $135,591 8.77 1.38 37.44 2405.7761.32DUMP TRUCK, HIGHWAY, 75,000 LBS GVW, 3 AXLE, 6X4 WITH REAR 16 - 20 CY DUMP BODY

HP D-on

EP 1110-1-8, Vol. 430 Nov 11

2-235


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

TRUCKS, OFF-HIGHWAYT550.10 RIGID FRAMESUBCATEGORY


487769DT55CA007 $690,208 27.70 6.60 28.15 66820.45115.30TRUCK, OFF-HIGHWAY, RIGID FRAME, 31.7 CY, 41.6 TON, 4X4, REAR DUMP

HP D-off

650773DT55CA002 $923,835 36.60 8.83 37.57 87227.13146.11TRUCK, OFF-HIGHWAY, RIGID FRAME, 46.9 CY, 57.7 TON, 4X4, REAR DUMP

HP D-off

938777DT55CA003 $1,276,107 50.10 12.19 54.22 1,41937.24206.17TRUCK, OFF-HIGHWAY, RIGID FRAME, 78.6 CY, 100 TON, 4X4, REAR DUMP

HP D-off


488HD325-6AT55KM009 $494,267 19.37 4.72 28.21 70714.4195.68TRUCK, OFF-HIGHWAY, RIGID FRAME, 31.4 CY, 44 TON, 4X4, REAR DUMP

HP D-off

1,042HD785-5T55KM012 $1,009,849 38.79 9.65 60.23 1,54229.05186.35TRUCK, OFF-HIGHWAY, RIGID FRAME, 78.7 CY, 100 TON, 4X4, REAR DUMP

HP D-off

1,486HD1500-5T55KM013 $2,328,348 93.31 22.25 85.89 5,50068.91354.01TRUCK, OFF-HIGHWAY, RIGID FRAME, 102 CY, 165 TON, 4X4, REAR DUMP

HP D-off

2,000730ET55KM014 $2,748,779 104.93 26.27 115.60 7,15078.74454.13TRUCK, OFF-HIGHWAY, RIGID FRAME, 145 CY, 205 TON, 4X4, REAR DUMP

HP D-off

0.20 ARTICULATED FRAMESUBCATEGORY


260D25DT55CA008 $435,132 26.91 4.25 21.22 42917.7191.63TRUCK, OFF-HIGHWAY, ARTICULATED FRAME, 18 CY, 25 TON, 4X4, REAR DUMP

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-236


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT


285D30DT55CA009 $515,446 31.58 5.04 23.26 47320.83107.96TRUCK, OFF-HIGHWAY, ARTICULATED FRAME, 22 CY, 30 TON, 4X4, REAR DUMP

HP D-off

214D250D SERIES II

T55CA010 $433,631 27.24 4.24 17.46 42417.8685.52TRUCK, OFF-HIGHWAY, ARTICULATED FRAME, 18 CY, 25 TON, 6X6, REAR DUMP

HP D-off

260D300E SERIES IIT55CA011 $512,593 32.38 5.01 21.22 48821.20100.90TRUCK, OFF-HIGHWAY, ARTICULATED FRAME, 22 CY, 30 TON, 6X6, REAR DUMP

HP D-off


HP D-off


HP D-off

DEERE & COMPANY

265250DT55JD001 $339,360 21.05 3.32 21.62 35513.8576.87TRUCK, OFF-HIGHWAY, ARTICULATED FRAME, 18 CY, 25 TON, 6X6, REAR DUMP

HP D-off


HP D-off


HP D-off


HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-237


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)


389HM350-2T55KM015 $391,658 22.34 3.83 31.74 63015.00105.51TRUCK, OFF-HIGHWAY, ARTICULATED FRAME, 19.1-25.9 CY, 35.7 TON, 6 X 6 X 2, REAR DUMP

HP D-off

430HM400-2T55KM016 $495,613 29.43 4.85 35.09 66819.57122.43TRUCK, OFF-HIGHWAY, ARTICULATED FRAME, 21.6-29.2 CY, 40.3 TON, 6 X 6 X 2, REAR DUMP

HP D-off

VOLVO CONSTRUCTION EQUIPMENT GROUP

299A-25E 4X4T55VO002 $387,252 23.85 3.79 24.40 42915.7288.31TRUCK, OFF-HIGHWAY, ARTICULATED FRAME, 14-18 CY, 25 TON, 4X4, REAR DUMP

HP D-off

299A-25ET55VO003 $408,472 25.49 3.99 24.40 47516.7490.01TRUCK, OFF-HIGHWAY, ARTICULATED FRAME, 14-18 CY, 25 TON, 6X6, REAR DUMP

HP D-off


HP D-off


HP D-off


HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-238


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

TRUCKS,OFF-HIGHWAY/PRIME MOVER TRACTORS & WAGONST560.10 PRIME MOVER TRACTORSSUBCATEGORY


938776DT56CA006 $1,420,948 56.26 13.58 60.59 1,16441.71230.37TRUCK, OFF-HIGHWAY, RIGID FRAME, PRIME MOVER TRACTOR, 4X4

HP D-off

TRUCKS, VACUUMT570.00 TRUCKS, VACUUMSUBCATEGORY

WASTEQUIP CUSCO INDUSTRIES

76INDUSTRIAL VAC 130

T57CU001 $120,521 9.59 1.24 8.01 766.0430.82TRAILER, VACUUM, 5,500 GAL, 750 CFM, REAR DOOR & HYDRAULIC DUMP SYSTEM

HP D-off

76SS INDUST. VAC 130

T57CU002 $147,943 11.79 1.53 8.01 767.4335.72TRAILER, VACUUM, 5,500 GAL, 750 CFM, STAINLESS STEEL, REAR DOOR & HYDRAULIC DUMP SYSTEM

HP D-off

3002127T57CU003 $126,886 10.10 1.31 31.62 1156.3658.49TRUCK, VACUUM, 3,500 GAL, 2,100 CFM, REAR DOOR & HYDRAULIC DUMP SYSTEM (ADD TRUCK COST)

HP D-off


HP D-off


HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-239


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

TRUCKS, WATER, OFF-HIGHWAYT600.00 TRUCKS, WATER, OFF-HIGHWAYSUBCATEGORY

KLEIN PRODUCTS, INC.

175KT-50 T60KI001 $281,547 18.07 2.87 18.45 32011.9162.80TRUCK, WATER, OFF-HIGHWAY, 5,000 GAL, W/CAT 613C TRACTOR

HP D-off

330KT-60 T60KI002 $436,940 27.12 4.45 34.78 58018.01108.70TRUCK, WATER, OFF-HIGHWAY, 6,000 GAL, W/CAT 621E TRACTOR

HP D-off


HP D-off


HP D-off

550KT-120 T60KI006 $855,153 52.67 8.71 57.97 1,09735.05202.95TRUCK, WATER, OFF-HIGHWAY, 12,000 GAL, W/CAT 651E TRACTOR

HP D-off


330STT-60 T60SO001 $505,995 31.73 5.16 34.78 61021.03118.35TRUCK, WATER, OFF-HIGHWAY, 6,000 GAL, W/CAT 621E TRACTOR

HP D-off


HP D-off


HP D-off

550STT-120 T60SO004 $883,296 54.74 9.00 57.97 1,14936.37206.11TRUCK, WATER, OFF-HIGHWAY, 12,000 GAL, W/CAT 651E TRACTOR

HP D-off

550STT-140 T60SO005 $898,092 55.72 9.15 57.97 1,18437.01208.17TRUCK, WATER, OFF-HIGHWAY, 14,000 GAL, W/CAT 651E TRACTOR

HP D-off

EP 1110-1-8, Vol. 430 Nov 11

2-240


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

TUNNEL/MINING EQUIPMENTT650.10 DRIFTING & TUNNELING DRILLSSUBCATEGORY

ATLAS COPCO WAGNER

158L2CT65WG012 $1,724,372 104.02 16.78 13.42 52068.79264.51156 HP D-offTUNNELING DRILL, 2 BOOM, 560-1,120 SF CROSS SECTION, RUBBER TIRED (ADD DRILL BITS AND DRILL STEEL COST)

HP E

158WL2CT65WG013 $2,592,729 156.75 25.23 13.42 728103.61386.91156 HP D-offTUNNELING DRILL, 4 BOOM, 700-1,600 SF CROSS SECTION, RUBBER TIRED (ADD DRILL BITS AND DRILL STEEL COST)

HP E

380WL4CT65WG014 $2,824,530 170.82 27.48 29.19 1,058112.89443.44224 HP D-offTUNNELING DRILL, 4 BOOM, 700-1,650 SF CROSS SECTION, RUBBER TIRED (ADD DRILL BITS AND DRILL STEEL COST)

HP E

WATER & CO2 BLASTERSW250.10 LOW PRESSURE, (< 5,000 PSI)SUBCATEGORY

SIOUX STEAM CLEANER CORPORATION

1S1.7 D250W25SD006 $5,811 1.16 0.07 0.08 40.657.10WATER BLASTER, LOW PRESSURE, STEAM CLEANER, 100 GPH, 250 PSI, 1.7 GPM

HP E

1S2 D250W25SD007 $6,193 1.24 0.07 0.08 50.698.30WATER BLASTER, LOW PRESSURE, STEAM CLEANER, 120 GPH, 250 PS, 2.0 GPM

HP E

1S2.7 D250W25SD008 $6,738 1.35 0.08 0.08 60.769.58WATER BLASTER, LOW PRESSURE, STEAM CLEANER, 160 GPH, 250 PSI, 2.7 GPM

HP E

EP 1110-1-8, Vol. 430 Nov 11

2-241


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

W25 SIOUX STEAM CLEANER CORPORATION (continued)

5C-4-E 2000W25SD001 $5,455 1.09 0.06 0.38 40.613.35WATER BLASTER, LOW PRESSURE, COLD WATER, 2,000 PSI, 4 GPM

HP E

12C-4-G 2800W25SD005 $6,383 1.28 0.07 3.73 40.717.40WATER BLASTER, LOW PRESSURE, COLD WATER, 2,800 PSI, 4 GPM

HP G

18C-5-G 3400W25SD003 $8,458 1.69 0.10 5.59 50.9510.52WATER BLASTER, LOW PRESSURE, COLD WATER, 3,400 PSI, 5 GPM

HP G

8H3.5*3000W25SD004 $12,390 2.42 0.14 2.48 61.359.02WATER BLASTER, LOW PRESSURE, HOT WATER, 3,000 PSI, 3.5 GPM, TRAILER MTD

HP G

11SF11W25SD009 $14,928 2.99 0.17 0.85 91.6714.89WATER BLASTER, LOW PRESSURE, STEAM GENERATOR, 15 PSI, 355 LB/HR STEAM, 55 GAL BOILER

HP E

3EN-140-H4-1800W25SD002 $14,080 2.82 0.16 0.23 71.577.56WATER BLASTER, LOW PRESSURE, HOT WATER, 1,800 PSI, 2.3 GPM

HP E


5COLD 3/1000GW25XX005 $2,040 0.41 0.02 1.55 40.232.76WATER BLASTER, LOW PRESSURE, COLD WATER, 700 PSI, 3 GPM

HP G

5COLD 4/1000GW25XX006 $2,852 0.57 0.03 1.55 40.323.17WATER BLASTER, LOW PRESSURE, COLD WATER, 1,200 PSI, 3 GPM

HP G


HP G


HP G

8HOT 4/1000GW25XX009 $7,987 1.60 0.09 2.48 60.896.84WATER BLASTER, LOW PRESSURE, HOT WATER/STEAM, 1,000 PSI, 4 GPM

HP G

24HOT 6/3000GW25XX010 $12,234 2.45 0.14 7.45 101.3714.52WATER BLASTER, LOW PRESSURE, HOT WATER/STEAM, 3,000 PSI, 6 GPM

HP G

EP 1110-1-8, Vol. 430 Nov 11

2-242


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

0.20 HIGH PRESSURE, (>= 5,000 PSI)SUBCATEGORY

NLB CORPORATION

2006200EW25NL001 $74,925 14.99 0.86 15.39 1188.3662.72WATER BLASTER, HIGH PRESSURE, 6,000 PSI, 50 GPM, SKID MTD, W/MODEL 10200 PUMP

HP E

150 201536DW25NL003 $80,865 16.17 0.93 22.95 789.0269.54WATER BLASTER, HIGH PRESSURE, 20,000 PSI, 13.2 GPM, SKID MTD, W/50 LF HOSE & CLEANING LANCE

HP D-off

33520253DW25NL002 $126,183 25.24 1.45 51.26 14014.07125.86WATER BLASTER, HIGH PRESSURE, 20,000 PSI, 22 GPM, SKID MTD (ADD TRUCK, FLATBED TRAILER & WATER TANKER)

HP D-off

70020600DW25NL005 $309,641 61.93 3.57 107.10 20034.54287.86WATER BLASTER, HIGH PRESSURE, 20,000 PSI, 53 GPM, SKID MTD (ADD TRUCK, FLATBED TRAILER & WATER TANKER)

HP D-off

344400W25NL004 $165,893 32.64 1.91 5.20 8018.2394.91WATER BLASTER, HIGH PRESSURE, HYDRODEMOLITION UNIT, CONCRETE BUSTER, SELF PROPELLED (ADD MODEL 20600D WATER BLASTER)

HP D-off

0.30 STEAM CLEANERSSUBCATEGORY

ALKOTA CLEANING SYSTEMS, INC.

1122W25AO00 $4,364 0.87 0.05 0.08 40.493.11WATER BLASTER, STEAM CLEANER, 400 PSI, 1.7 GPM

HP E


HP E


HP E

EP 1110-1-8, Vol. 430 Nov 11

2-243


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

W25 ALKOTA CLEANING SYSTEMS, INC. (continued)


HP E

1246W25AO00 $9,776 1.96 0.11 0.08 71.095.89WATER BLASTER, STEAM GENERATOR, 100 PSI, 1.0 GPM

HP E

0.40 CO2 BLASTERSSUBCATEGORY

COLD JET

20P750BW25CJ001 $77,402 10.32 0.84 1.13 346.0027.07CARBON DIOXIDE (CO2) BLASTER/PELLETIZER, 600 LBS/HR, SINGLE HOSE DELIVERY (ADD 65-100 CFM COMPRESSOR)

HP E

24P1500BW25CJ002 $120,154 16.02 1.30 1.36 379.3141.42CARBON DIOXIDE (CO2) BLASTER/PELLETIZER, 1,200 LBS/HR, SINGLE HOSE DELIVERY (ADD 65-150 CFM COMPRESSOR)

HP E

24P3000BW25CJ003 $189,926 25.32 2.06 1.36 6614.7264.25CARBON DIOXIDE (CO2) BLASTER/PELLETIZER, 1,200 LBS/HR, DUAL HOSE DELIVERY (ADD 65-200 CFM COMPRESSOR)

HP E

0.50 WET ABRASIVE BLASTING SYSTEM (TORBO)SUBCATEGORY

KEIZER TECHNOLOGIES AMERICAS, INC

350TORBO M120W25KZ001 $21,669 1.41 0.25 0.00 40.962.61WATER BLASTER, WET ABRASIVE BLASTER, 4.2 CF TANK CAP, 170 PSI, (INCLUDES HOSES & NOZZLE, ADD 350 CFM AIR COMPRESSOR)

CFM A

EP 1110-1-8, Vol. 430 Nov 11

2-244


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

W25 KEIZER TECHNOLOGIES AMERICAS, INC (continued)

350TORBO M120W25KZ002 $23,990 1.56 0.27 0.00 41.052.88WATER BLASTER, WET ABRASIVE BLASTER, 4.2 CF TANK CAP, 170 PSI, W/MIX RUST INHIBITOR INJECTOR (INCLUDES HOSES & NOZZLE, ADD 350 CFM AIR COMPRESSOR)

CFM A

350LOC RESTORATION UNIT

W25KZ003 $24,525 1.59 0.28 0.00 41.082.95WATER BLASTER, WET ABRASIVE BLASTER, 4.2 CF TANK CAP, 170 PSI, W/LOC RESTORATION UNIT (INCLUDES HOSES & NOZZLE, ADD 350 CFM AIR COMPRESSOR)

CFM A

385TORBO M320W25KZ004 $34,889 2.27 0.40 0.00 81.544.20WATER BLASTER, WET ABRASIVE BLASTER, 13.0 CF TANK CAP, 170 PSI, (INCLUDES HOSES & NOZZLE, ADD 385 CFM AIR COMPRESSOR)

CFM A

385TORBO XL320W25KZ005 $41,196 2.68 0.47 0.00 81.814.96WATER BLASTER, WET ABRASIVE BLASTER, 13.0 CF TANK CAP, 170 PSI, (INCLUDES HOSES & NOZZLE, ADD 385 CFM AIR COMPRESSOR)

CFM A

385TORBO XL320W25KZ006 $41,987 2.73 0.48 0.00 91.855.05WATER BLASTER, WET ABRASIVE BLASTER, 19.0 CF TANK CAP, 170 PSI, (INCLUDES HOSES & NOZZLE, ADD 385 CFM AIR COMPRESSOR)

CFM A

385TORBO XL320W25KZ007 $44,784 2.91 0.51 0.00 91.975.39WATER BLASTER, WET ABRASIVE BLASTER, 19.0 CF TANK CAP, 170 PSI, W/MIX RUST INHIBATOR INJECTOR,(INCLUDES HOSES & NOZZLE, ADD 385 CFM AIR COMPRESSOR)

CFM A

EP 1110-1-8, Vol. 430 Nov 11

2-245


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

WATER TANKSW300.10 PORTABLE WITH WHEELSSUBCATEGORY


8EWT-8CW30SO00 $56,501 3.64 0.58 1.70 1302.409.52WATER TANK, PORTABLE, TRAILER MTD, SELF ELEVATING, 8,000 GAL, 10" PIPE

HP G


HP G


HP G

0.20 SKID MOUNTEDSUBCATEGORY


WST-8 W30SO00 $36,151 2.41 0.37 0.00 1071.584.41WATER TANK, PORTABLE, SKID MTD, 8,000 GAL, 10" PIPE



EP 1110-1-8, Vol. 430 Nov 11

2-246


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 4)

11/30/2011

CAT

WELDERSW350.10 ENGINE DRIVENSUBCATEGORY


11GAS 150 ACW35XX020 $2,531 0.24 0.03 2.86 20.153.69WELDER, ENGINE DRIVEN, GAS, AC, 150 AMP, 4.5 KW, PORTABLE, SKID MTD

HP G

17GAS 225 AC/DC-CC

W35XX021 $6,687 0.61 0.07 4.42 60.386.27WELDER, ENGINE DRIVEN, GAS, AC/DC-CC, 225 AMP, 5-8 KW, TRAILER MTD

HP G

18GAS 250 AC/DC-CC/CV

W35XX022 $6,891 0.63 0.07 4.68 60.396.59WELDER, ENGINE DRIVEN, GAS, AC/DC-CC/CV, 250 AMP, 9 KW, TRAILER MTD

HP G

45GAS 300 DC-CCW35XX023 $11,912 1.10 0.13 11.70 140.6815.41WELDER, ENGINE DRIVEN, GAS, DC-CC, 300 AMP, 3 KW, TRAILER MTD

HP G

48DIESEL 400 DC-CC/CV

W35XX024 $17,591 1.63 0.19 6.20 211.0110.51WELDER, ENGINE DRIVEN, DIESEL, DC-CC/CV, 400 AMP, 2-10 KW, TRAILER MTD

HP D-off

42DIESEL 500 DC-CC/CV

W35XX025 $16,871 1.56 0.18 5.43 180.969.49WELDER, ENGINE DRIVEN, DIESEL, DC-CC/CV, 500 AMP, 4 KW, TRAILER MTD

HP D-off

0.20 ELECTRIC DRIVENSUBCATEGORY

LINCOLN ELECTRIC COMPANY

5SP-180TW35LC018 $820 0.11 0.01 0.12 10.070.37WELDER, ELECTRIC DRIVEN, 30-180 AMP, WIRE FEEDER

HP E

15LINCWELD 225/125

W35LC010 $650 0.09 0.01 0.36 10.060.68WELDER, ELECTRIC DRIVEN, 225 AMP, STICK

HP E

27IDEAL ARC R3R-300

W35LC011 $3,229 0.43 0.04 0.66 40.261.72WELDER, ELECTRIC DRIVEN, 300 AMP, STICK

HP E

EP 1110-1-8, Vol. 430 Nov 11

2-247


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

11/30/2011

CAT

(Vol. 4)

W35 LINCOLN ELECTRIC COMPANY (continued)35IDEAL ARC

R3R-400W35LC012 $4,165 0.56 0.05 0.85 50.332.21WELDER, ELECTRIC DRIVEN, 400 AMP,

STICK HP E

41IDEAL ARC R3R-500

W35LC013 $4,463 0.60 0.05 1.00 50.352.50WELDER, ELECTRIC DRIVEN, 500 AMP, STICK

HP E

26PROCUT 80W35LC020 $4,058 0.54 0.04 0.63 10.311.86WELDER, ELECTRIC DRIVEN, 85 AMP, PLASMA CUTTING TORCH

HP E

EP 1110-1-8, Vol. 430 Nov 11

2-248

2-253

Table 2-2. Hourly Rate Elements

This Table Contains All Hourly Rate Elements as

Described in Chapter 2

For

Average and Severe Operating Conditions.

Refer to Chapter 2, Section II. Operating Condition

EP 1110-1-8, Vol. 430 Nov 11

2-249

CAT ID. NO. DEPR FCCM FUEL FOGTIRE WEAR

TIRE REPAIR REPAIR

TOTAL RATE FCCM FUEL FOG

TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR

Table 2-2 . HOURLY RATE ELEMENTS

AVERAGE OPERATING CONDITIONS SEVERE OPERATING CONDITIONS

EP 1110-1-8(Vol. 4)11/30/2011

4REGION

A10A10AR001 0.44 0.04 0.00 0.00 0.00 0.00 0.36 0.84A10AR002 2.11 0.17 0.00 0.20 0.00 0.00 1.72 4.20A10RS003 11.47 1.23 17.57 1.86 0.53 0.08 11.74 44.48A10RS004 11.55 1.24 17.57 1.86 0.53 0.08 11.81 44.64A10RS005 11.60 1.25 17.57 1.86 0.53 0.08 11.87 44.76A10RS006 11.63 1.25 17.57 1.86 0.53 0.08 11.90 44.82A10RS007 11.77 1.26 17.57 1.86 0.53 0.08 12.04 45.11A10RS008 22.82 2.44 23.70 2.50 0.80 0.12 23.33 75.71A10SE001 1.82 0.15 0.00 0.00 0.00 0.00 1.48 3.45A10SE002 2.14 0.17 0.00 0.00 0.00 0.00 1.74 4.05

A15A15IA001 1.48 0.19 6.85 0.85 0.08 0.01 1.64 11.10A15IA002 3.39 0.44 13.46 1.66 0.08 0.01 3.75 22.79A15IA003 4.36 0.57 21.30 2.63 0.15 0.02 4.83 33.86A15IA004 4.37 0.57 21.30 2.63 0.15 0.02 4.85 33.89A15IA005 4.98 0.65 21.30 2.63 0.15 0.02 5.52 35.25A15IA006 11.01 1.43 36.72 4.54 0.29 0.05 12.19 66.23A15IA007 11.65 1.52 36.72 4.54 0.29 0.05 12.90 67.67A15IA008 8.70 1.14 41.00 5.07 0.29 0.05 9.64 65.89A15IA009 7.87 1.03 37.94 4.69 0.29 0.05 8.72 60.59A15IA010 16.27 2.11 48.96 6.05 0.29 0.05 18.00 91.73A15SR002 11.12 1.46 53.86 6.65 0.44 0.07 12.33 85.93A15SR004 0.93 0.12 9.55 1.18 0.08 0.01 1.04 12.91A15SR005 1.26 0.17 9.79 1.21 0.08 0.01 1.40 13.92A15SR006 0.93 0.12 9.30 1.15 0.08 0.01 1.04 12.63A15SR007 0.93 0.12 9.42 1.16 0.08 0.01 1.04 12.76

2 192

EP 1110-1-8, Vol. 430 Nov 11

2-250


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

A15 cont.A15SR008 2.14 0.28 15.06 1.86 0.15 0.02 2.38 21.89A15SR009 2.14 0.28 15.18 1.88 0.15 0.02 2.38 22.03A15SR010 4.62 0.61 28.15 3.48 0.29 0.05 5.12 42.32A15SR011 5.44 0.72 36.72 4.54 0.29 0.05 6.04 53.80A15SR012 5.36 0.71 36.72 4.54 0.29 0.05 5.95 53.62A15SR013 9.57 1.25 55.08 6.81 0.29 0.05 10.59 83.64A15SR014 10.35 1.37 55.08 6.81 0.63 0.10 11.49 85.83A15XX019 0.80 0.11 7.36 1.04 0.08 0.01 0.89 10.29A15XX020 1.55 0.20 3.67 0.45 0.08 0.01 1.72 7.68A15XX021 1.07 0.14 12.27 1.73 0.08 0.01 1.19 16.49A15XX022 1.59 0.21 4.28 0.53 0.08 0.01 1.77 8.47A15XX023 1.13 0.15 15.96 2.25 0.08 0.01 1.26 20.84A15XX024 1.80 0.24 6.12 0.76 0.08 0.01 1.99 11.00A15XX025 1.24 0.16 14.73 2.08 0.08 0.01 1.38 19.68A15XX026 2.02 0.26 8.57 1.06 0.08 0.01 2.23 14.23A15XX027 1.29 0.17 22.09 3.12 0.08 0.01 1.43 28.19A15XX028 2.06 0.27 9.79 1.21 0.08 0.01 2.29 15.71A15XX029 1.40 0.18 17.18 2.42 0.08 0.01 1.55 22.82A15XX030 2.74 0.36 10.40 1.28 0.08 0.01 3.03 17.90A15XX031 4.01 0.52 13.46 1.66 0.08 0.01 4.44 24.18A15XX032 3.64 0.48 14.08 1.74 0.15 0.02 4.03 24.14A15XX033 4.82 0.64 20.81 2.57 0.29 0.05 5.35 34.53A15XX034 6.73 0.88 30.60 3.78 0.29 0.05 7.46 49.79A15XX035 7.17 0.94 33.66 4.16 0.29 0.05 7.95 54.22A15XX036 7.73 1.01 33.66 4.16 0.29 0.05 8.57 55.47A15XX037 8.27 1.08 37.94 4.69 0.29 0.05 9.16 61.48A15XX038 12.61 1.64 44.06 5.44 0.29 0.05 13.96 78.05

2 193

EP 1110-1-8, Vol. 430 Nov 11

2-251


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)11/30/2011

4REGION

A15 cont.A15XX039 13.15 1.72 56.30 6.96 0.42 0.07 14.57 93.19A15XX040 14.17 1.85 61.20 7.56 0.42 0.07 15.69 100.96A15XX041 0.18 0.03 0.30 0.15 0.00 0.00 0.17 0.83A15XX042 0.25 0.03 0.43 0.21 0.00 0.00 0.22 1.14A15XX043 0.37 0.05 0.61 0.30 0.00 0.00 0.33 1.66A15XX044 0.44 0.06 0.91 0.45 0.00 0.00 0.39 2.25A15XX045 0.62 0.09 1.52 0.75 0.00 0.00 0.56 3.54A15XX046 0.76 0.11 1.82 0.90 0.00 0.00 0.69 4.28

A20A20CK001 0.24 0.02 0.00 0.00 0.00 0.00 0.47 0.73A20CK002 0.14 0.01 0.00 0.00 0.00 0.00 0.27 0.42A20CK003 0.27 0.02 0.00 0.00 0.00 0.00 0.52 0.81A20CK005 0.34 0.02 0.00 0.00 0.00 0.00 0.66 1.02A20CK006 0.17 0.01 0.00 0.00 0.00 0.00 0.33 0.51A20CK008 0.19 0.01 0.00 0.00 0.00 0.00 0.37 0.57A20CK010 0.20 0.01 0.00 0.00 0.00 0.00 0.40 0.61A20CM010 0.64 0.04 0.00 0.06 0.00 0.00 1.26 2.00A20CM011 0.82 0.06 0.00 0.06 0.00 0.00 1.62 2.56A20CM012 0.93 0.06 0.00 0.13 0.00 0.00 1.82 2.94A20CM013 2.72 0.19 0.00 0.28 0.11 0.02 5.35 8.67A20CM014 3.13 0.24 0.00 0.41 0.48 0.07 6.23 10.56A20CM015 3.77 0.28 0.00 0.50 0.29 0.05 7.46 12.35A20CM016 2.42 0.17 0.00 0.30 0.00 0.00 4.75 7.64A20CM017 0.11 0.00 0.00 0.00 0.00 0.00 0.22 0.33A20CM018 0.12 0.00 0.00 0.00 0.00 0.00 0.24 0.36A20CM019 0.15 0.01 0.00 0.00 0.00 0.00 0.31 0.47A20CM020 0.12 0.01 0.00 0.00 0.00 0.00 0.25 0.38

2 194

EP 1110-1-8, Vol. 430 Nov 11

2-252


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

A20 cont.A20WC002 0.18 0.01 0.11 0.19 0.00 0.00 0.36 0.85A20WC004 0.53 0.04 0.85 0.12 0.00 0.00 1.04 2.58A20XX001 0.39 0.02 0.00 0.00 0.00 0.00 0.73 1.14A20XX002 0.45 0.02 0.00 0.00 0.00 0.00 0.84 1.31A20XX003 0.56 0.02 0.00 0.00 0.00 0.00 1.05 1.63A20XX004 0.73 0.03 0.00 0.00 0.00 0.00 1.37 2.13A20XX005 1.04 0.04 0.00 0.00 0.00 0.00 1.94 3.02A20XX006 1.28 0.05 0.00 0.00 0.00 0.00 2.37 3.70A20XX007 1.58 0.06 0.00 0.00 0.00 0.00 2.93 4.57A20XX008 2.11 0.09 0.00 0.00 0.00 0.00 3.92 6.12A20XX021 0.20 0.01 0.00 0.00 0.00 0.00 0.39 0.60A20XX022 0.23 0.02 0.00 0.00 0.00 0.00 0.46 0.71A20XX023 0.28 0.02 0.00 0.00 0.00 0.00 0.55 0.85A20XX024 0.29 0.02 0.00 0.00 0.00 0.00 0.57 0.88A20XX025 0.41 0.03 0.00 0.00 0.00 0.00 0.80 1.24

A25A25RS006 9.66 0.66 0.00 1.16 0.00 0.00 9.92 21.40A25RS008 11.07 0.76 0.00 1.80 0.00 0.00 11.37 25.00A25XX001 8.16 0.56 0.00 0.64 0.00 0.00 8.37 17.73A25XX002 9.50 0.65 0.00 1.51 0.00 0.00 9.75 21.41A25XX003 10.39 0.71 0.00 2.09 0.00 0.00 10.67 23.86

A30A30BG003 37.56 3.86 25.89 4.70 4.74 0.74 48.54 126.03A30BG005 42.03 4.03 25.89 4.70 0.00 0.00 53.75 130.40A30BK011 26.31 2.66 12.37 1.53 3.24 0.51 33.93 80.55A30BK013 31.86 3.17 16.76 2.07 2.36 0.37 40.98 97.57

2 195

EP 1110-1-8, Vol. 430 Nov 11

2-253


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)11/30/2011

4REGION

A30 cont.A30BK015 36.58 3.66 21.27 2.63 3.17 0.49 47.07 114.87A30BK018 42.02 4.03 21.27 2.63 0.00 0.00 53.74 123.69A30BK019 29.48 2.85 12.14 1.50 0.38 0.06 37.74 84.15A30BK020 38.65 3.73 20.00 2.47 0.46 0.07 49.47 114.85A30BK021 40.89 3.92 20.35 2.51 0.00 0.00 52.30 119.97A30BK022 30.08 3.00 16.76 2.07 2.36 0.37 38.69 93.33A30BK023 35.81 3.43 16.76 2.07 0.00 0.00 45.79 103.86A30BK024 29.12 3.86 19.39 2.40 1.79 0.28 31.80 88.64A30CA002 28.26 2.83 20.11 2.48 2.49 0.39 36.38 92.94A30CA007 20.32 2.66 11.28 1.39 0.74 0.12 22.15 58.66A30CA008 32.77 3.28 25.89 3.20 3.02 0.47 42.18 110.81A30CA009 46.53 4.46 20.00 2.47 0.00 0.00 59.50 132.96A30CA013 28.36 2.72 20.11 2.48 0.00 0.00 36.26 89.93A30CA014 32.73 3.29 17.69 2.19 3.17 0.49 42.15 101.71A30CA015 55.02 5.28 20.11 2.48 0.00 0.00 70.36 153.25A30CA016 46.02 4.41 20.00 2.47 0.00 0.00 58.85 131.75A30CH001 28.82 2.90 12.72 1.57 3.24 0.51 37.14 86.90A30CH002 31.81 3.17 17.57 2.17 2.36 0.37 40.91 98.36A30CH003 33.26 3.19 17.57 2.17 0.00 0.00 42.53 98.72A30CH004 33.48 3.34 17.57 2.17 2.50 0.39 43.07 102.52A30CH005 36.54 3.64 20.00 2.47 3.02 0.47 47.00 113.14A30CH006 44.28 4.25 23.12 2.86 0.00 0.00 56.62 131.13A30GC002 4.26 0.42 2.89 0.36 0.22 0.03 5.47 13.65A30GC004 6.28 0.60 4.74 0.59 0.00 0.00 8.03 20.24A30LD001 11.50 1.57 11.59 1.43 1.57 0.24 12.63 40.53A30MP001 13.63 1.76 8.43 1.04 0.00 0.00 14.81 39.67A30MP002 15.29 1.97 10.54 1.30 0.00 0.00 16.61 45.71

2 196

EP 1110-1-8, Vol. 430 Nov 11

2-254


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

A30 cont.A30RT001 43.08 5.56 28.99 3.58 0.11 0.02 46.81 128.15A30RT002 45.15 5.83 28.99 3.58 0.20 0.03 49.07 132.85A30XX001 10.16 1.59 10.85 1.13 1.03 0.16 7.63 32.55A30XX002 12.73 1.95 10.85 1.13 0.00 0.00 9.52 36.18

A35A35AE001 0.62 0.06 1.06 2.10 0.08 0.01 0.70 4.63A35AE002 1.04 0.09 1.06 2.80 0.08 0.01 1.15 6.23A35AE003 1.32 0.11 1.06 3.15 0.05 0.01 1.44 7.14A35AE004 1.55 0.13 1.06 4.05 0.05 0.01 1.69 8.54A35AE005 1.76 0.15 1.06 6.25 0.10 0.02 1.93 11.27

A40A40CA008 73.00 5.94 87.98 10.87 0.00 0.00 99.18 276.97A40CA009 83.64 6.81 99.45 12.29 0.00 0.00 113.65 315.84A40CW001 113.60 9.25 145.35 17.96 0.00 0.00 154.35 440.51A40RT001 45.09 3.83 35.19 4.35 2.31 0.36 61.79 152.92A40RT002 61.45 5.00 38.25 4.73 0.00 0.00 83.49 192.92A40RT003 75.69 6.16 70.38 8.70 0.00 0.00 102.84 263.77A40RT005 103.27 8.41 122.40 15.12 0.00 0.00 140.31 389.51A40RT006 114.37 9.31 122.40 15.12 0.00 0.00 155.40 416.60

A45A45AE001 2.02 0.15 0.00 7.10 0.05 0.01 2.49 11.82A45AE002 3.15 0.22 0.00 14.25 0.05 0.01 3.87 21.55A45AE003 7.33 0.51 0.00 16.85 0.04 0.01 8.98 33.72A45RS001 8.04 0.57 8.43 1.54 0.07 0.01 9.85 28.51A45RS002 26.09 1.81 25.39 3.64 0.00 0.00 31.89 88.82

2 197

EP 1110-1-8, Vol. 430 Nov 11

2-255


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)11/30/2011

4REGION

A45 cont.A45SE003 6.30 0.45 3.16 2.39 0.12 0.02 7.73 20.17A45SE004 3.89 0.28 2.77 0.89 0.15 0.02 4.80 12.80

B10B10CC007 4.92 0.53 3.83 3.54 0.14 0.02 6.72 19.70B10CC008 5.11 0.58 34.72 8.40 0.72 0.11 7.04 56.68B10CC009 6.54 0.75 42.60 9.76 1.25 0.20 9.06 70.16B10CC010 7.70 0.88 42.60 10.01 1.25 0.20 10.64 73.28B10CC011 2.33 0.25 1.05 1.52 0.00 0.00 3.17 8.32B10CC012 2.42 0.25 3.83 1.29 0.00 0.00 3.29 11.08B10CC013 3.18 0.33 3.83 1.34 0.00 0.00 4.32 13.00B10CC014 0.72 0.08 0.26 0.63 0.00 0.00 0.98 2.67B10CL015 16.51 1.80 1.58 3.28 0.81 0.13 22.59 46.70B10CL021 8.79 0.96 1.84 0.91 0.47 0.07 12.05 25.09B10CL025 29.44 3.12 10.53 5.22 0.24 0.04 40.06 88.65B10CL027 2.28 0.24 0.00 0.00 0.00 0.00 3.10 5.62B10CL032 0.45 0.05 0.53 0.26 0.00 0.00 0.61 1.90B10CL034 0.90 0.10 1.05 0.52 0.00 0.00 1.23 3.80B10CL036 0.38 0.04 0.42 0.21 0.00 0.00 0.51 1.56B10CL040 0.52 0.06 1.05 0.52 0.00 0.00 0.71 2.86B10CL042 0.34 0.04 0.26 0.13 0.00 0.00 0.47 1.24B10CL045 0.44 0.05 0.53 0.26 0.00 0.00 0.60 1.88B10EM001 45.20 4.87 5.32 3.25 1.45 0.23 61.71 122.03B10EM002 2.87 0.33 0.53 1.26 0.39 0.06 3.99 9.43B10EM003 2.97 0.31 0.00 0.00 0.00 0.00 4.03 7.31B10KB001 14.43 1.90 5.00 2.48 0.52 0.08 19.70 44.11B10KB002 25.91 3.39 11.58 5.74 0.59 0.09 35.30 82.60B10RC006 20.09 2.19 2.40 5.69 0.89 0.14 27.49 58.89

2 198

EP 1110-1-8, Vol. 430 Nov 11

2-256


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

B10 cont.B10RC007 14.21 1.54 0.79 2.89 0.54 0.08 19.42 39.47B10RC008 16.99 1.83 1.58 3.28 0.54 0.08 23.20 47.50B10RC016 24.85 2.69 3.95 7.46 0.89 0.14 33.96 73.94B10RC027 15.80 1.66 2.11 3.05 0.00 0.00 21.46 44.08B10RC028 17.74 1.87 3.16 3.82 0.00 0.00 24.11 50.70B10RC029 20.05 2.11 4.21 4.59 0.00 0.00 27.25 58.21B10RC030 21.85 2.30 5.27 6.36 0.00 0.00 29.69 65.47B10RC031 23.07 2.43 6.32 7.14 0.00 0.00 31.34 70.30B10RC032 21.82 2.37 2.63 5.80 0.89 0.14 29.84 63.49B10SN031 7.41 0.86 1.32 2.00 0.97 0.15 10.27 22.98B10SN032 11.71 1.31 1.58 2.53 0.98 0.15 16.12 34.38B10SN033 14.53 1.61 1.58 2.28 0.95 0.15 19.94 41.04B10SN034 15.80 1.74 1.05 2.02 0.98 0.15 21.68 43.42B10SN035 16.62 1.83 1.58 2.43 0.98 0.15 22.79 46.38B10SN036 15.52 1.71 2.37 2.93 0.98 0.15 21.30 44.96

B15B15BM001 5.33 0.47 8.43 1.04 0.00 0.00 5.20 20.47B15EC001 23.46 2.08 9.14 1.13 0.69 0.11 22.94 59.55B15EC002 14.40 1.28 10.54 1.30 0.34 0.05 14.08 41.99B15EC003 22.76 2.00 24.24 2.99 0.10 0.02 22.23 74.34B15EC004 25.27 2.21 16.81 2.08 0.00 0.00 24.68 71.05B15MB001 0.93 0.08 0.00 0.10 0.00 0.00 0.91 2.02B15MB002 1.13 0.10 0.00 0.14 0.00 0.00 1.10 2.47B15MB003 1.58 0.14 0.00 0.24 0.09 0.01 1.55 3.61B15MB004 1.83 0.17 3.83 0.40 0.09 0.01 1.80 8.13B15RS001 4.60 0.41 8.43 1.04 0.11 0.02 4.50 19.11B15RS005 5.96 0.53 8.43 1.04 0.18 0.03 5.83 22.00

2 199

EP 1110-1-8, Vol. 430 Nov 11

2-257


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)11/30/2011

4REGION

B15 cont.B15TB001 2.59 0.23 3.90 0.48 0.15 0.02 2.53 9.90B15TB002 2.60 0.23 3.90 0.48 0.15 0.02 2.55 9.93B15WD001 4.13 0.37 8.43 1.04 0.11 0.02 4.04 18.14B15WD002 4.30 0.38 8.43 1.04 0.11 0.02 4.20 18.48

B20B20BN001 1.25 0.11 9.37 1.32 0.04 0.01 1.37 13.47B20BN002 1.72 0.15 17.89 2.52 0.07 0.01 1.89 24.25B20BN003 2.02 0.18 29.82 4.21 0.06 0.01 2.22 38.52B20BN005 2.50 0.22 30.24 4.26 0.06 0.01 2.75 40.04B20BN006 3.12 0.28 30.24 4.26 0.06 0.01 3.42 41.39B20BN007 3.52 0.32 14.97 1.85 0.23 0.04 3.88 24.81B20MQ001 3.44 0.30 8.85 1.09 0.02 0.00 3.78 17.48B20MQ003 5.19 0.46 14.97 1.85 0.06 0.01 5.70 28.24B20MQ004 6.65 0.60 18.34 2.27 0.28 0.04 7.32 35.50B20MQ005 58.03 5.13 92.23 12.90 0.83 0.13 63.76 233.01

B25B25HB001 2.15 0.19 0.00 0.00 0.00 0.00 1.81 4.15 2.64 0.19 0.00 0.00 0.00 0.00 2.55 5.38B25HB003 3.45 0.30 0.00 0.00 0.00 0.00 2.91 6.66 4.24 0.31 0.00 0.00 0.00 0.00 4.10 8.65B25HB005 4.48 0.39 0.00 0.00 0.00 0.00 3.78 8.65 5.51 0.40 0.00 0.00 0.00 0.00 5.32 11.23B25HB007 5.29 0.46 0.00 0.00 0.00 0.00 4.46 10.21 6.51 0.48 0.00 0.00 0.00 0.00 6.28 13.27B25HB008 6.16 0.54 0.00 0.00 0.00 0.00 5.20 11.90 7.58 0.55 0.00 0.00 0.00 0.00 7.32 15.45B25HB009 6.79 0.59 0.00 0.00 0.00 0.00 5.73 13.11 8.36 0.61 0.00 0.00 0.00 0.00 8.07 17.04B25HB010 7.15 0.63 0.00 0.00 0.00 0.00 6.04 13.82 8.80 0.64 0.00 0.00 0.00 0.00 8.50 17.94B25HB011 7.35 0.64 0.00 0.00 0.00 0.00 6.20 14.19 9.04 0.66 0.00 0.00 0.00 0.00 8.73 18.43B25HB012 7.77 0.68 0.00 0.00 0.00 0.00 6.56 15.01 9.56 0.70 0.00 0.00 0.00 0.00 9.23 19.49B25HB013 8.03 0.70 0.00 0.00 0.00 0.00 6.78 15.51 9.88 0.72 0.00 0.00 0.00 0.00 9.54 20.14

2 200

EP 1110-1-8, Vol. 430 Nov 11

2-258


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

B25 cont.B25HB014 8.38 0.73 0.00 0.00 0.00 0.00 7.08 16.19 10.32 0.75 0.00 0.00 0.00 0.00 9.96 21.03B25HB015 8.69 0.76 0.00 0.00 0.00 0.00 7.34 16.79 10.69 0.78 0.00 0.00 0.00 0.00 10.32 21.79B25XX001 0.97 0.08 0.00 0.00 0.00 0.00 0.82 1.87 1.19 0.09 0.00 0.00 0.00 0.00 1.15 2.43B25XX002 1.44 0.13 0.00 0.00 0.00 0.00 1.21 2.78 1.77 0.13 0.00 0.00 0.00 0.00 1.71 3.61B25XX003 1.77 0.16 0.00 0.00 0.00 0.00 1.50 3.43 2.18 0.16 0.00 0.00 0.00 0.00 2.11 4.45B25XX004 1.94 0.17 0.00 0.00 0.00 0.00 1.64 3.75 2.39 0.17 0.00 0.00 0.00 0.00 2.31 4.87B25XX005 2.26 0.20 0.00 0.00 0.00 0.00 1.91 4.37 2.78 0.20 0.00 0.00 0.00 0.00 2.69 5.67B25XX006 2.55 0.22 0.00 0.00 0.00 0.00 2.15 4.92 3.13 0.23 0.00 0.00 0.00 0.00 3.03 6.39B25XX007 2.72 0.24 0.00 0.00 0.00 0.00 2.30 5.26 3.35 0.24 0.00 0.00 0.00 0.00 3.23 6.82B25XX008 3.18 0.28 0.00 0.00 0.00 0.00 2.68 6.14 3.91 0.29 0.00 0.00 0.00 0.00 3.78 7.98B25XX009 3.34 0.29 0.00 0.00 0.00 0.00 2.82 6.45 4.11 0.30 0.00 0.00 0.00 0.00 3.97 8.38B25XX010 3.56 0.31 0.00 0.00 0.00 0.00 3.00 6.87 4.38 0.32 0.00 0.00 0.00 0.00 4.23 8.93B25XX011 3.73 0.33 0.00 0.00 0.00 0.00 3.15 7.21 4.59 0.33 0.00 0.00 0.00 0.00 4.43 9.35B25XX012 4.16 0.36 0.00 0.00 0.00 0.00 3.52 8.04 5.12 0.37 0.00 0.00 0.00 0.00 4.95 10.44B25XX013 5.60 0.49 0.00 0.00 0.00 0.00 4.73 10.82 6.89 0.50 0.00 0.00 0.00 0.00 6.66 14.05B25XX014 5.98 0.52 0.00 0.00 0.00 0.00 5.05 11.55 7.36 0.54 0.00 0.00 0.00 0.00 7.10 15.00B25XX015 7.22 0.63 0.00 0.00 0.00 0.00 6.10 13.95 8.89 0.65 0.00 0.00 0.00 0.00 8.58 18.12B25XX016 7.28 0.64 0.00 0.00 0.00 0.00 6.15 14.07 8.96 0.65 0.00 0.00 0.00 0.00 8.65 18.26B25XX017 7.86 0.69 0.00 0.00 0.00 0.00 6.64 15.19 9.68 0.71 0.00 0.00 0.00 0.00 9.34 19.73B25XX018 7.46 0.65 0.00 0.00 0.00 0.00 6.30 14.41 9.18 0.67 0.00 0.00 0.00 0.00 8.87 18.72B25XX019 8.35 0.73 0.00 0.00 0.00 0.00 7.05 16.13 10.27 0.75 0.00 0.00 0.00 0.00 9.92 20.94

B30B30CR001 0.53 0.04 0.00 0.00 0.00 0.00 0.49 1.06B30CR002 0.60 0.05 0.00 0.00 0.00 0.00 0.54 1.19B30CR003 0.66 0.05 0.00 0.00 0.00 0.00 0.60 1.31B30CR004 0.70 0.06 0.00 0.00 0.00 0.00 0.64 1.40B30CR005 0.87 0.07 0.00 0.00 0.00 0.00 0.79 1.73

2 201

EP 1110-1-8, Vol. 430 Nov 11

2-259


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)11/30/2011

4REGION

B30 cont.B30CR006 1.07 0.09 0.00 0.00 0.00 0.00 0.98 2.14B30CR009 0.92 0.07 0.00 0.00 0.00 0.00 0.85 1.84B30CR010 1.13 0.09 0.00 0.00 0.00 0.00 1.03 2.25B30CR011 1.42 0.11 0.00 0.00 0.00 0.00 1.30 2.83B30CR012 1.66 0.13 0.00 0.00 0.00 0.00 1.52 3.31B30GB001 0.49 0.04 0.00 0.00 0.00 0.00 0.39 0.92B30GB002 0.64 0.05 0.00 0.00 0.00 0.00 0.51 1.20B30GB003 0.79 0.06 0.00 0.00 0.00 0.00 0.63 1.48B30GB004 1.14 0.09 0.00 0.00 0.00 0.00 0.91 2.14B30GB005 1.36 0.11 0.00 0.00 0.00 0.00 1.09 2.56B30GB006 3.06 0.25 0.00 0.00 0.00 0.00 2.62 5.93B30GB007 3.31 0.27 0.00 0.00 0.00 0.00 2.84 6.42B30GB008 3.67 0.29 0.00 0.00 0.00 0.00 3.15 7.11B30GB009 4.07 0.33 0.00 0.00 0.00 0.00 3.49 7.89B30GB010 5.16 0.41 0.00 0.00 0.00 0.00 4.42 9.99B30GB011 1.98 0.16 0.00 0.00 0.00 0.00 1.81 3.95B30GB012 2.06 0.16 0.00 0.00 0.00 0.00 1.88 4.10B30GB013 2.13 0.17 0.00 0.00 0.00 0.00 1.95 4.25B30GB014 2.80 0.22 0.00 0.00 0.00 0.00 2.56 5.58B30GB015 2.90 0.23 0.00 0.00 0.00 0.00 2.66 5.79B30GB016 4.85 0.39 0.00 0.00 0.00 0.00 4.44 9.68B30GB017 5.26 0.42 0.00 0.00 0.00 0.00 4.81 10.49B30GB018 0.39 0.03 0.00 0.00 0.00 0.00 0.31 0.73

B35B35HE001 0.88 0.08 0.00 0.00 0.00 0.00 0.75 1.71 1.09 0.08 0.00 0.00 0.00 0.00 1.05 2.22B35HE002 1.04 0.09 0.00 0.00 0.00 0.00 0.87 2.00 1.27 0.09 0.00 0.00 0.00 0.00 1.23 2.59B35HE003 1.47 0.13 0.00 0.00 0.00 0.00 1.24 2.84 1.81 0.13 0.00 0.00 0.00 0.00 1.74 3.68

2 202

EP 1110-1-8, Vol. 430 Nov 11

2-260


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

B35 cont.B35HE004 1.77 0.16 0.00 0.00 0.00 0.00 1.50 3.43 2.18 0.16 0.00 0.00 0.00 0.00 2.10 4.44B35HE005 2.03 0.18 0.00 0.00 0.00 0.00 1.71 3.92 2.50 0.18 0.00 0.00 0.00 0.00 2.41 5.09B35HE006 2.53 0.22 0.00 0.00 0.00 0.00 2.14 4.89 3.11 0.23 0.00 0.00 0.00 0.00 3.01 6.35B35HE007 2.75 0.24 0.00 0.00 0.00 0.00 2.32 5.31 3.38 0.25 0.00 0.00 0.00 0.00 3.27 6.90B35HE008 3.61 0.32 0.00 0.00 0.00 0.00 3.05 6.98 4.44 0.32 0.00 0.00 0.00 0.00 4.29 9.05B35HE009 3.79 0.33 0.00 0.00 0.00 0.00 3.20 7.32 4.66 0.34 0.00 0.00 0.00 0.00 4.50 9.50B35HE010 4.38 0.38 0.00 0.00 0.00 0.00 3.70 8.46 5.39 0.39 0.00 0.00 0.00 0.00 5.21 10.99B35HE011 4.74 0.42 0.00 0.00 0.00 0.00 4.01 9.17 5.84 0.43 0.00 0.00 0.00 0.00 5.64 11.91B35HE012 5.19 0.45 0.00 0.00 0.00 0.00 4.38 10.02 6.38 0.47 0.00 0.00 0.00 0.00 6.16 13.01B35HE013 5.75 0.50 0.00 0.00 0.00 0.00 4.85 11.10 7.08 0.52 0.00 0.00 0.00 0.00 6.83 14.43B35HE014 6.58 0.58 0.00 0.00 0.00 0.00 5.55 12.71 8.10 0.59 0.00 0.00 0.00 0.00 7.82 16.51B35HE015 7.15 0.63 0.00 0.00 0.00 0.00 6.04 13.82 8.80 0.64 0.00 0.00 0.00 0.00 8.50 17.94B35HE016 8.54 0.75 0.00 0.00 0.00 0.00 7.21 16.50 10.51 0.77 0.00 0.00 0.00 0.00 10.15 21.43B35HE017 9.83 0.86 0.00 0.00 0.00 0.00 8.30 18.99 12.09 0.88 0.00 0.00 0.00 0.00 11.68 24.65B35HE018 0.85 0.08 0.00 0.00 0.00 0.00 0.72 1.65 1.09 0.09 0.00 0.00 0.00 0.00 1.05 2.23B35HE019 0.97 0.09 0.00 0.00 0.00 0.00 0.82 1.88 1.25 0.10 0.00 0.00 0.00 0.00 1.21 2.56B35HE020 1.39 0.13 0.00 0.00 0.00 0.00 1.17 2.69 1.78 0.14 0.00 0.00 0.00 0.00 1.72 3.64B35HE021 1.75 0.17 0.00 0.00 0.00 0.00 1.48 3.40 2.25 0.18 0.00 0.00 0.00 0.00 2.17 4.60B35HE022 2.02 0.20 0.00 0.00 0.00 0.00 1.71 3.93 2.60 0.20 0.00 0.00 0.00 0.00 2.51 5.31B35HE023 2.41 0.23 0.00 0.00 0.00 0.00 2.04 4.68 3.10 0.24 0.00 0.00 0.00 0.00 3.00 6.34B35HE024 2.66 0.26 0.00 0.00 0.00 0.00 2.25 5.17 3.42 0.27 0.00 0.00 0.00 0.00 3.30 6.99B35HE025 3.45 0.34 0.00 0.00 0.00 0.00 2.91 6.70 4.43 0.35 0.00 0.00 0.00 0.00 4.28 9.06B35HE026 3.52 0.34 0.00 0.00 0.00 0.00 2.97 6.83 4.53 0.35 0.00 0.00 0.00 0.00 4.37 9.25B35HE027 4.27 0.42 0.00 0.00 0.00 0.00 3.60 8.29 5.49 0.43 0.00 0.00 0.00 0.00 5.30 11.22B35HE028 4.41 0.43 0.00 0.00 0.00 0.00 3.73 8.57 5.67 0.44 0.00 0.00 0.00 0.00 5.48 11.59B35HE029 5.09 0.50 0.00 0.00 0.00 0.00 4.30 9.89 6.54 0.51 0.00 0.00 0.00 0.00 6.32 13.37B35HE030 5.61 0.55 0.00 0.00 0.00 0.00 4.73 10.89 7.21 0.56 0.00 0.00 0.00 0.00 6.96 14.73

2 203

EP 1110-1-8, Vol. 430 Nov 11

2-261


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)11/30/2011

4REGION

B35 cont.B35HE031 6.82 0.66 0.00 0.00 0.00 0.00 5.76 13.24 8.77 0.68 0.00 0.00 0.00 0.00 8.47 17.92B35HE032 7.27 0.71 0.00 0.00 0.00 0.00 6.14 14.12 9.35 0.73 0.00 0.00 0.00 0.00 9.02 19.10B35HE033 9.26 0.90 0.00 0.00 0.00 0.00 7.82 17.98 11.91 0.93 0.00 0.00 0.00 0.00 11.50 24.34B35HE034 10.32 1.00 0.00 0.00 0.00 0.00 8.72 20.04 13.27 1.03 0.00 0.00 0.00 0.00 12.81 27.11B35HE035 2.85 0.31 0.00 0.00 0.00 0.00 2.41 5.57 3.57 0.31 0.00 0.00 0.00 0.00 3.44 7.32B35HE036 2.98 0.32 0.00 0.00 0.00 0.00 2.51 5.81 3.72 0.33 0.00 0.00 0.00 0.00 3.59 7.64B35HE037 3.35 0.36 0.00 0.00 0.00 0.00 2.83 6.54 4.19 0.37 0.00 0.00 0.00 0.00 4.04 8.60B35HE038 4.55 0.49 0.00 0.00 0.00 0.00 3.84 8.88 5.68 0.50 0.00 0.00 0.00 0.00 5.49 11.67B35HE039 5.08 0.54 0.00 0.00 0.00 0.00 4.29 9.91 6.36 0.56 0.00 0.00 0.00 0.00 6.14 13.06B35HE040 5.25 0.56 0.00 0.00 0.00 0.00 4.43 10.24 6.56 0.57 0.00 0.00 0.00 0.00 6.34 13.47B35HE041 5.62 0.60 0.00 0.00 0.00 0.00 4.75 10.97 7.03 0.62 0.00 0.00 0.00 0.00 6.79 14.44B35HE042 7.23 0.77 0.00 0.00 0.00 0.00 6.11 14.11 9.04 0.79 0.00 0.00 0.00 0.00 8.73 18.56B35HE043 7.44 0.80 0.00 0.00 0.00 0.00 6.28 14.52 9.30 0.81 0.00 0.00 0.00 0.00 8.98 19.09B35HE044 9.67 1.04 0.00 0.00 0.00 0.00 8.17 18.88 12.09 1.06 0.00 0.00 0.00 0.00 11.68 24.83B35HE045 10.02 1.07 0.00 0.00 0.00 0.00 8.46 19.55 12.52 1.10 0.00 0.00 0.00 0.00 12.09 25.71B35HE046 11.91 1.28 0.00 0.00 0.00 0.00 10.06 23.25 14.89 1.30 0.00 0.00 0.00 0.00 14.38 30.57B35HE047 12.69 1.36 0.00 0.00 0.00 0.00 10.71 24.76 15.86 1.39 0.00 0.00 0.00 0.00 15.31 32.56B35SA001 6.36 0.56 0.00 0.00 0.00 0.00 5.37 12.29 7.83 0.57 0.00 0.00 0.00 0.00 7.56 15.96B35SA003 9.54 0.84 0.00 0.00 0.00 0.00 8.06 18.44 11.74 0.86 0.00 0.00 0.00 0.00 11.34 23.94B35SA004 14.32 1.25 0.00 0.00 0.00 0.00 12.09 27.66 17.63 1.29 0.00 0.00 0.00 0.00 17.02 35.94B35SA005 19.10 1.67 0.00 0.00 0.00 0.00 16.13 36.90 23.51 1.72 0.00 0.00 0.00 0.00 22.70 47.93B35SA006 23.90 2.09 0.00 0.00 0.00 0.00 20.18 46.17 29.41 2.15 0.00 0.00 0.00 0.00 28.40 59.96B35SA007 28.64 2.51 0.00 0.00 0.00 0.00 24.18 55.33 35.24 2.57 0.00 0.00 0.00 0.00 34.03 71.84B35SA008 38.18 3.34 0.00 0.00 0.00 0.00 32.24 73.76 46.99 3.43 0.00 0.00 0.00 0.00 45.37 95.79B35SA009 47.71 4.18 0.00 0.00 0.00 0.00 40.29 92.18 58.72 4.29 0.00 0.00 0.00 0.00 56.70 119.71B35SA010 57.26 5.02 0.00 0.00 0.00 0.00 48.36 110.64 70.48 5.15 0.00 0.00 0.00 0.00 68.05 143.68B35XX001 3.51 0.31 0.00 0.00 0.00 0.00 2.96 6.78 4.32 0.32 0.00 0.00 0.00 0.00 4.17 8.81

2 204

EP 1110-1-8, Vol. 430 Nov 11

2-262


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

B35 cont.B35XX002 3.95 0.35 0.00 0.00 0.00 0.00 3.33 7.63 4.86 0.35 0.00 0.00 0.00 0.00 4.69 9.90B35XX003 4.36 0.38 0.00 0.00 0.00 0.00 3.68 8.42 5.37 0.39 0.00 0.00 0.00 0.00 5.19 10.95B35XX004 4.98 0.44 0.00 0.00 0.00 0.00 4.20 9.62 6.12 0.45 0.00 0.00 0.00 0.00 5.91 12.48B35XX005 5.59 0.49 0.00 0.00 0.00 0.00 4.72 10.80 6.88 0.50 0.00 0.00 0.00 0.00 6.64 14.02B35XX006 6.87 0.60 0.00 0.00 0.00 0.00 5.80 13.27 8.46 0.62 0.00 0.00 0.00 0.00 8.17 17.25B35XX007 3.53 0.34 0.00 0.00 0.00 0.00 2.98 6.85 4.53 0.35 0.00 0.00 0.00 0.00 4.38 9.26B35XX008 4.03 0.39 0.00 0.00 0.00 0.00 3.40 7.82 5.18 0.40 0.00 0.00 0.00 0.00 5.00 10.58B35XX009 4.34 0.42 0.00 0.00 0.00 0.00 3.67 8.43 5.58 0.43 0.00 0.00 0.00 0.00 5.39 11.40B35XX010 5.16 0.50 0.00 0.00 0.00 0.00 4.36 10.02 6.64 0.52 0.00 0.00 0.00 0.00 6.41 13.57B35XX011 5.71 0.56 0.00 0.00 0.00 0.00 4.82 11.09 7.34 0.57 0.00 0.00 0.00 0.00 7.09 15.00B35XX012 7.24 0.70 0.00 0.00 0.00 0.00 6.11 14.05 9.30 0.72 0.00 0.00 0.00 0.00 8.98 19.00B35XX013 0.80 0.09 0.00 0.00 0.00 0.00 0.68 1.57 1.00 0.09 0.00 0.00 0.00 0.00 0.97 2.06B35XX014 0.90 0.10 0.00 0.00 0.00 0.00 0.76 1.76 1.12 0.10 0.00 0.00 0.00 0.00 1.08 2.30B35XX015 1.34 0.14 0.00 0.00 0.00 0.00 1.13 2.61 1.67 0.15 0.00 0.00 0.00 0.00 1.61 3.43B35XX016 1.53 0.16 0.00 0.00 0.00 0.00 1.29 2.98 1.91 0.17 0.00 0.00 0.00 0.00 1.84 3.92B35XX017 1.67 0.18 0.00 0.00 0.00 0.00 1.41 3.26 2.08 0.18 0.00 0.00 0.00 0.00 2.01 4.27B35XX018 3.56 0.38 0.00 0.00 0.00 0.00 3.01 6.95 4.45 0.39 0.00 0.00 0.00 0.00 4.30 9.14B35XX019 3.80 0.41 0.00 0.00 0.00 0.00 3.21 7.42 4.75 0.42 0.00 0.00 0.00 0.00 4.59 9.76B35XX020 4.29 0.46 0.00 0.00 0.00 0.00 3.62 8.37 5.37 0.47 0.00 0.00 0.00 0.00 5.18 11.02B35XX021 4.67 0.50 0.00 0.00 0.00 0.00 3.95 9.12 5.84 0.51 0.00 0.00 0.00 0.00 5.64 11.99B35XX022 5.90 0.63 0.00 0.00 0.00 0.00 4.98 11.51 7.37 0.65 0.00 0.00 0.00 0.00 7.12 15.14B35XX023 6.32 0.68 0.00 0.00 0.00 0.00 5.34 12.34 7.90 0.69 0.00 0.00 0.00 0.00 7.63 16.22

C05C05OL001 0.16 0.00 0.67 0.09 0.00 0.00 0.49 1.41C05OL002 0.25 0.01 1.37 0.19 0.00 0.00 0.78 2.60C05OL003 0.31 0.01 1.52 0.21 0.00 0.00 0.94 2.99C05OL004 0.34 0.01 1.67 0.24 0.00 0.00 1.03 3.29

2 205

EP 1110-1-8, Vol. 430 Nov 11

2-263


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)11/30/2011

4REGION

C10C10BO001 0.94 0.04 0.88 0.09 0.00 0.00 1.30 3.25C10BO003 0.36 0.02 1.17 0.12 0.00 0.00 0.50 2.17C10BO004 0.42 0.02 1.75 0.18 0.00 0.00 0.58 2.95C10BO008 3.70 0.17 1.32 0.14 0.00 0.00 5.13 10.46C10BO009 1.71 0.09 1.17 0.12 0.00 0.00 2.65 5.74C10BO011 4.51 0.24 1.17 0.12 0.00 0.00 6.99 13.03C10BO013 10.31 0.55 2.78 0.29 0.00 0.00 15.98 29.91C10BO015 4.01 0.21 0.73 0.08 0.00 0.00 6.22 11.25C10BO016 5.03 0.27 1.32 0.14 0.00 0.00 7.80 14.56C10RX001 6.72 0.36 1.17 0.12 0.00 0.00 10.42 18.79C10RX002 9.28 0.49 2.05 0.22 0.00 0.00 14.39 26.43C10RX003 15.53 0.82 4.82 0.51 0.00 0.00 24.08 45.76C10WC003 0.95 0.04 0.58 0.06 0.00 0.00 1.32 2.95C10WC006 1.17 0.05 1.61 0.17 0.00 0.00 1.62 4.62C10WC007 1.79 0.08 2.63 0.28 0.00 0.00 2.48 7.26C10WC008 3.22 0.15 1.32 0.14 0.00 0.00 4.47 9.30C10WC010 2.18 0.12 3.22 0.34 0.00 0.00 3.37 9.23C10WC015 6.38 0.29 2.05 0.22 0.00 0.00 8.85 17.79C10WC016 7.13 0.38 2.92 0.31 0.00 0.00 11.06 21.80C10WC017 2.88 0.15 1.32 0.14 0.00 0.00 4.47 8.96C10WC019 6.76 0.36 2.92 0.31 0.00 0.00 10.49 20.84

C15C15BL001 1.90 0.11 0.11 0.56 0.00 0.00 2.35 5.03C15BL003 7.52 0.43 0.57 1.81 0.00 0.00 9.28 19.61C15BL004 8.64 0.50 0.85 2.22 0.00 0.00 10.67 22.88C15BL005 12.12 0.70 1.70 2.94 0.00 0.00 14.97 32.43

2 206

EP 1110-1-8, Vol. 430 Nov 11

2-264


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

C15 cont.C15BL006 45.20 4.76 53.55 6.62 0.00 0.00 55.82 165.95C15ED001 1.63 0.09 2.50 0.35 0.00 0.00 2.01 6.58C15ED002 0.98 0.06 2.05 0.29 0.00 0.00 1.21 4.59C15XX001 13.77 1.47 29.78 3.67 0.42 0.07 17.06 66.24

C20C20WC002 2.21 0.14 2.96 0.42 0.19 0.03 2.16 8.11C20XX001 1.55 0.10 1.82 0.26 0.13 0.02 1.52 5.40

C25C25AJ001 0.77 0.05 1.36 0.19 0.00 0.00 0.85 3.22C25AJ003 1.31 0.09 1.36 0.19 0.00 0.00 1.44 4.39C25AJ004 1.48 0.10 2.05 0.29 0.00 0.00 1.63 5.55C25AJ005 1.66 0.12 2.50 0.35 0.00 0.00 1.82 6.45C25AJ006 1.87 0.13 2.50 0.35 0.00 0.00 2.06 6.91C25AJ007 1.98 0.14 2.50 0.35 0.00 0.00 2.17 7.14C25AJ008 1.44 0.18 1.17 0.22 0.00 0.00 1.36 4.37C25AJ009 1.53 0.20 1.17 0.22 0.00 0.00 1.44 4.56C25AJ010 1.64 0.21 1.17 0.22 0.00 0.00 1.54 4.78C25AJ011 1.76 0.22 1.17 0.22 0.00 0.00 1.65 5.02C25AJ012 1.86 0.24 1.17 0.22 0.00 0.00 1.75 5.24C25AJ013 1.97 0.25 1.17 0.22 0.00 0.00 1.86 5.47C25AJ015 1.90 0.13 4.55 0.64 0.00 0.00 2.09 9.31C25AJ016 2.14 0.15 5.46 0.77 0.00 0.00 2.35 10.87C25AJ018 2.22 0.15 5.46 0.77 0.00 0.00 2.44 11.04C25AJ019 3.05 0.21 7.73 1.09 0.00 0.00 3.35 15.43C25ST001 0.43 0.03 1.82 0.26 0.00 0.00 0.47 3.01C25ST002 0.44 0.03 2.05 0.29 0.00 0.00 0.48 3.29

2 207

EP 1110-1-8, Vol. 430 Nov 11

2-265


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)11/30/2011

4REGION

C25 cont.C25SV001 27.89 3.59 6.85 1.14 0.33 0.05 26.31 66.16C25SV002 26.22 3.37 6.85 1.14 0.30 0.05 24.73 62.66C25SV003 13.07 1.69 3.16 0.53 0.22 0.03 12.34 31.04C25WC002 0.54 0.04 1.82 0.26 0.00 0.00 0.59 3.25

C35C35AF002 1.68 0.18 0.00 2.00 0.03 0.00 2.22 6.11C35AF004 4.81 0.50 3.67 2.45 0.06 0.01 6.36 17.86C35AF005 7.02 0.73 6.61 2.82 0.13 0.02 9.28 26.61C35AL002 4.69 0.50 3.67 1.45 0.20 0.03 6.23 16.77C35AL003 1.57 0.18 0.30 0.34 0.20 0.03 2.12 4.74C35AL008 2.83 0.29 0.00 0.30 0.00 0.00 3.72 7.14C35AL013 1.39 0.15 0.00 0.40 0.10 0.02 1.85 3.91C35AL014 7.37 0.76 7.47 1.42 0.06 0.01 9.72 26.81C35AV006 9.80 1.01 1.22 2.61 0.11 0.02 12.94 27.71C35AV008 3.04 0.31 0.43 2.21 0.00 0.00 4.01 10.00C35AV009 3.71 0.38 0.97 2.48 0.00 0.00 4.88 12.42C35AV010 6.91 0.71 1.58 2.78 0.00 0.00 9.10 21.08C35AV011 5.47 0.56 0.73 2.36 0.00 0.00 7.21 16.33C35AV012 15.83 1.63 1.22 3.11 0.00 0.00 20.86 42.65

C40C40CC001 5.01 0.35 0.57 0.31 0.00 0.00 5.50 11.74C40MU001 0.55 0.04 1.82 0.26 0.03 0.00 0.61 3.31C40MU002 1.15 0.08 2.96 0.42 0.03 0.00 1.28 5.92C40MU003 0.54 0.04 1.82 0.26 0.03 0.00 0.61 3.30C40MU004 0.63 0.05 1.82 0.26 0.03 0.00 0.70 3.49C40ST001 0.33 0.03 0.03 0.22 0.03 0.00 0.37 1.01

2 208

EP 1110-1-8, Vol. 430 Nov 11

2-266


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

C40 cont.C40ST002 0.36 0.03 1.25 0.18 0.03 0.00 0.41 2.26C40ST003 0.43 0.03 0.11 0.31 0.03 0.00 0.48 1.39C40ST005 0.57 0.04 0.09 0.35 0.03 0.00 0.64 1.72C40XX001 0.58 0.04 0.11 0.26 0.00 0.00 0.64 1.63C40XX002 0.62 0.04 1.59 0.22 0.00 0.00 0.68 3.15C40XX003 0.89 0.06 0.17 0.29 0.00 0.00 0.97 2.38C40XX004 0.89 0.06 1.82 0.26 0.00 0.00 0.98 4.01C40XX005 1.17 0.08 0.28 0.40 0.00 0.00 1.28 3.21C40XX006 1.62 0.11 0.28 0.40 0.00 0.00 1.78 4.19C40XX007 1.51 0.11 2.05 0.29 0.00 0.00 1.66 5.62

C45C45GO010 21.93 1.79 11.26 1.39 0.00 0.00 29.80 66.17C45GO011 33.79 2.75 22.64 2.80 0.00 0.00 45.91 107.89C45GO012 45.27 3.69 20.69 2.56 0.00 0.00 61.50 133.71C45GO013 18.20 1.48 11.26 1.39 0.00 0.00 24.73 57.06C45GO014 25.09 2.04 12.00 1.48 0.00 0.00 34.09 74.70C45GO016 49.48 4.03 28.15 3.48 0.00 0.00 67.23 152.37C45GO018 61.73 5.03 41.00 5.07 0.00 0.00 83.88 196.71C45GO020 73.21 5.96 55.08 6.81 0.00 0.00 99.47 240.53C45GO026 7.86 0.64 8.84 1.25 0.00 0.00 10.67 29.26C45GO027 9.98 0.81 6.12 0.76 0.00 0.00 13.57 31.24C45GO028 15.89 1.29 6.12 0.76 0.00 0.00 21.59 45.65C45GO029 10.56 0.86 8.84 1.25 0.00 0.00 14.35 35.86C45GO031 59.92 4.88 47.12 5.82 0.00 0.00 81.42 199.16C45MJ001 1.14 0.09 3.68 0.52 0.00 0.00 1.55 6.98C45MW002 6.52 0.54 3.18 0.39 0.09 0.01 8.87 19.60C45MW003 8.27 0.68 3.18 0.39 0.12 0.02 11.26 23.92

2 209

EP 1110-1-8, Vol. 430 Nov 11

2-267


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)11/30/2011

4REGION

C55C55M3001 2.71 0.24 10.46 1.48 0.06 0.01 3.31 18.27C55M3002 6.17 0.54 6.94 0.86 0.00 0.00 7.53 22.04C55M3003 7.26 0.64 12.25 1.51 0.00 0.00 8.85 30.51C55OE001 30.94 2.71 0.00 0.00 0.00 0.00 37.75 71.40C55OE002 39.73 3.48 0.00 0.00 0.00 0.00 48.47 91.68C55OE003 60.49 5.30 0.00 0.00 0.00 0.00 73.80 139.59C55OE006 5.80 0.51 8.55 1.06 0.05 0.01 7.08 23.06C55OE009 10.95 0.97 14.68 1.81 0.10 0.02 13.37 41.90C55OE011 10.13 0.89 20.92 2.58 0.10 0.02 12.37 47.01C55OE012 12.88 1.13 20.92 2.58 0.10 0.02 15.72 53.35C55SC001 8.93 0.79 9.25 1.14 0.06 0.01 10.90 31.08C55SC002 15.47 1.37 22.77 2.81 0.20 0.03 18.89 61.54C55SC005 51.32 4.54 27.85 3.44 0.85 0.13 62.67 150.80C55SC006 55.37 4.89 27.85 3.44 0.85 0.13 67.61 160.14

C60C60CQ001 2.00 0.14 10.23 1.44 0.00 0.00 2.43 16.24C60CQ002 0.45 0.03 2.63 0.37 0.00 0.00 0.55 4.03C60CQ003 0.49 0.03 3.80 0.54 0.00 0.00 0.59 5.45C60CQ010 2.07 0.14 10.23 1.44 0.00 0.00 2.52 16.40C60CQ011 3.44 0.24 9.65 1.62 0.00 0.00 4.20 19.15C60CQ012 3.45 0.24 9.65 1.62 0.00 0.00 4.21 19.17C60CQ013 3.48 0.24 9.65 1.62 0.00 0.00 4.25 19.24C60CQ014 2.14 0.15 2.19 1.09 0.00 0.00 2.62 8.19C60CQ016 4.40 0.30 12.28 2.06 0.00 0.00 5.36 24.40C60FE002 0.23 0.02 0.58 0.08 0.00 0.00 0.28 1.19C60FE006 0.49 0.03 2.63 0.37 0.00 0.00 0.59 4.11

2 210

EP 1110-1-8, Vol. 430 Nov 11

2-268


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

C60 cont.C60FE007 0.51 0.03 3.80 0.54 0.00 0.00 0.62 5.50C60FE009 1.63 0.11 5.85 0.83 0.00 0.00 1.98 10.40C60LY001 4.16 0.28 2.92 0.41 0.00 0.00 5.07 12.84C60LY002 6.15 0.42 10.23 1.44 0.00 0.00 7.50 25.74C60LY005 0.48 0.03 3.80 0.54 0.00 0.00 0.58 5.43C60LY011 11.88 0.81 4.68 0.78 0.00 0.00 14.50 32.65

C65C65ST007 0.22 0.01 0.05 0.02 0.00 0.00 0.72 1.02C65ST008 0.23 0.01 0.11 0.05 0.00 0.00 0.75 1.15C65ST009 0.27 0.01 0.16 0.08 0.00 0.00 0.89 1.41C65ST013 0.50 0.02 1.17 0.17 0.00 0.00 1.65 3.51C65WC003 0.38 0.02 0.11 0.19 0.00 0.00 1.23 1.93C65WC004 0.24 0.01 0.16 0.22 0.00 0.00 0.79 1.42C65WC005 0.46 0.02 1.06 0.15 0.00 0.00 1.50 3.19

C75C75BD004 5.16 0.83 10.31 1.45 0.17 0.03 5.28 23.23C75BD005 6.42 1.05 16.94 2.39 0.49 0.08 6.58 33.95C75BD006 9.35 1.53 27.00 3.81 0.82 0.13 9.59 52.23C75BD007 3.70 0.60 9.33 1.32 0.23 0.04 3.79 19.01C75BD008 4.94 0.80 10.31 1.45 0.23 0.04 5.06 22.83C75BD009 6.64 1.08 16.94 2.39 0.49 0.08 6.80 34.42C75BD010 11.09 1.81 10.40 1.38 0.82 0.13 11.36 36.99C75BD011 14.69 2.40 15.91 2.10 2.04 0.32 15.06 52.52C75GV014 29.91 5.11 29.38 3.89 15.91 2.48 30.88 117.56C75GV016 69.63 11.66 36.72 4.86 25.04 3.91 71.66 223.48C75GV019 29.90 5.11 29.38 3.89 15.91 2.48 30.87 117.54

2 211

EP 1110-1-8, Vol. 430 Nov 11

2-269


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)11/30/2011

4REGION

C75 cont.C75GV020 47.91 8.18 30.60 4.05 25.04 3.91 49.46 169.15C75GV021 7.42 1.21 15.22 2.15 0.52 0.08 7.61 34.21C75GV022 9.15 1.50 13.46 1.78 0.87 0.14 9.38 36.28C75GV023 17.32 2.92 18.60 2.46 7.48 1.17 17.85 67.80C75GV024 26.94 4.47 21.18 2.80 7.48 1.17 27.69 91.73C75GV025 48.75 8.13 30.60 4.05 15.07 2.35 50.14 159.09C75GV028 16.69 2.82 18.60 2.46 6.19 0.97 17.20 64.93C75PB002 28.49 4.71 22.64 3.00 4.12 0.64 29.27 92.87C75TD003 22.87 3.79 22.03 2.91 6.41 1.00 23.50 82.51C75TD007 42.94 7.16 30.23 4.00 7.77 1.21 44.16 137.47C75TD008 39.67 6.63 30.23 4.00 13.87 2.16 40.82 137.38C75TE001 21.96 3.57 15.91 2.10 2.16 0.34 22.50 68.54C75TE002 30.12 4.91 18.60 2.46 3.53 0.55 30.87 91.04

C80C80GV006 37.43 6.85 42.16 4.84 1.44 0.22 33.51 126.45 42.78 6.91 55.76 6.40 5.60 0.87 41.02 159.34C80GV013 88.33 20.13 30.04 3.45 13.76 2.15 101.74 259.60 98.15 20.23 38.30 4.40 55.80 8.70 119.29 344.87C80GV014 88.56 20.18 30.04 3.45 13.76 2.15 102.00 260.14 98.40 20.28 38.30 4.40 55.80 8.70 119.60 345.48C80GV015 88.88 20.25 30.04 3.45 13.76 2.15 102.37 260.90 98.76 20.35 38.30 4.40 55.80 8.70 120.03 346.34C80GV016 125.52 28.55 27.63 3.18 16.23 2.53 144.52 348.16 139.46 28.69 35.29 4.05 64.89 10.12 169.45 451.95C80GV020 40.17 8.24 42.16 4.84 1.98 0.31 41.12 138.82 45.19 8.28 55.76 6.40 7.73 1.21 49.14 173.71C80GV025 24.41 4.48 31.62 3.63 1.15 0.18 21.85 87.32 27.89 4.51 41.82 4.80 4.53 0.71 26.75 111.01C80GV026 36.77 6.76 36.68 4.21 2.11 0.33 32.94 119.80 42.02 6.81 48.51 5.57 8.27 1.29 40.31 152.78C80GV029 37.21 6.85 42.16 4.84 2.53 0.39 33.33 127.31 42.52 6.91 55.76 6.40 9.98 1.56 40.80 163.93C80GV030 37.27 6.86 42.16 4.84 2.53 0.39 33.39 127.44 42.60 6.92 55.76 6.40 9.98 1.56 40.87 164.09C80GV031 37.59 7.74 42.16 4.84 2.53 0.39 38.50 133.75 42.29 7.77 55.76 6.40 9.98 1.56 46.01 169.77C80GV032 49.62 10.31 44.48 5.11 10.59 1.65 50.89 172.65 55.82 10.36 58.83 6.75 41.53 6.48 60.81 240.58C80LB009 31.27 5.75 38.47 4.42 1.84 0.29 28.01 110.05 35.74 5.79 50.88 5.84 7.42 1.16 34.29 141.12

2 212

EP 1110-1-8, Vol. 430 Nov 11

2-270


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

C80 cont.C80LB011 31.57 5.83 38.47 4.42 2.53 0.39 28.29 111.50 36.08 5.87 50.88 5.84 10.00 1.56 34.63 144.86C80TD001 34.24 7.18 19.56 2.24 6.13 0.96 35.17 105.48 38.52 7.22 25.04 2.88 24.71 3.85 42.02 144.24C80TD002 43.00 8.96 23.96 2.75 5.93 0.93 44.12 129.65 48.37 9.01 30.81 3.54 23.25 3.63 52.72 171.33C80TD005 46.40 10.70 65.99 7.58 7.51 1.17 53.54 192.89 51.55 10.76 86.07 9.88 29.79 4.65 62.77 255.47C80TE002 19.48 3.60 26.35 3.03 1.59 0.25 17.46 71.76 22.27 3.63 34.85 4.00 6.37 0.99 21.38 93.49C80TE003 25.63 4.74 39.00 4.48 2.41 0.38 22.98 99.62 29.29 4.78 51.58 5.92 9.56 1.49 28.13 130.75C80TE008 17.08 2.85 13.70 2.18 5.30 0.83 13.16 55.10 19.92 2.88 18.12 2.88 20.76 3.24 16.65 84.45C80XX001 8.78 1.45 25.82 4.10 1.11 0.17 6.75 48.18 10.24 1.46 34.15 5.43 4.43 0.69 8.54 64.94C80XX002 11.52 1.91 31.62 5.02 1.75 0.27 8.87 60.96 13.44 1.93 41.82 6.65 7.05 1.10 11.22 83.21

C85C85KC003 44.43 9.99 17.12 1.66 0.00 0.00 48.24 121.44 55.54 10.09 22.53 2.18 0.00 0.00 63.83 154.17C85KC004 28.06 6.31 11.50 1.11 0.00 0.00 30.47 77.45 35.07 6.37 15.13 1.47 0.00 0.00 40.31 98.35C85KC005 32.33 7.27 13.76 1.33 0.00 0.00 35.11 89.80 40.41 7.34 18.11 1.76 0.00 0.00 46.45 114.07C85KC006 75.40 18.55 18.02 1.90 0.00 0.00 91.45 205.32 92.15 18.74 23.72 2.51 0.00 0.00 117.74 254.86C85KC007 27.15 6.09 11.50 1.01 0.00 0.00 27.62 73.37 32.58 6.15 15.13 1.33 0.00 0.00 35.39 90.58C85KC008 53.51 13.17 20.41 2.16 0.00 0.00 64.90 154.15 65.40 13.30 26.86 2.84 0.00 0.00 83.56 191.96C85LB001 32.33 7.27 13.37 1.30 0.00 0.00 35.11 89.38 40.41 7.34 17.60 1.71 0.00 0.00 46.45 113.51C85LB014 42.24 9.50 18.35 1.78 0.00 0.00 45.87 117.74 52.80 9.59 24.14 2.34 0.00 0.00 60.69 149.56C85LB015 58.39 13.13 18.35 1.78 0.00 0.00 63.40 155.05 72.98 13.26 24.14 2.34 0.00 0.00 83.89 196.61C85LB016 67.78 16.68 18.35 1.94 0.00 0.00 82.21 186.96 82.84 16.85 24.14 2.55 0.00 0.00 105.84 232.22C85LB019 41.60 8.35 25.11 3.76 0.00 0.00 47.99 126.81 51.19 8.44 32.83 4.92 0.00 0.00 65.98 163.36C85LB021 58.45 13.11 25.11 2.43 0.00 0.00 75.33 174.43 70.14 13.23 32.83 3.18 0.00 0.00 99.95 219.33C85LB024 26.34 5.91 12.73 1.12 0.00 0.00 26.80 72.90 31.61 5.96 16.75 1.48 0.00 0.00 34.34 90.14C85MA002 63.78 14.31 30.06 2.91 0.00 0.00 82.20 193.26 76.54 14.44 39.30 3.81 0.00 0.00 109.07 243.16C85MA003 83.38 20.68 35.36 3.74 0.00 0.00 118.82 261.98 104.23 20.91 46.24 4.89 0.00 0.00 162.72 338.99C85MA005 50.91 11.45 21.96 2.13 0.00 0.00 55.28 141.73 63.64 11.56 28.90 2.80 0.00 0.00 73.15 180.05C85MA006 56.01 13.78 21.96 2.32 0.00 0.00 67.94 162.01 68.46 13.92 28.90 3.05 0.00 0.00 87.47 201.80

2 213

EP 1110-1-8, Vol. 430 Nov 11

2-271


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)11/30/2011

4REGION

C85 cont.C85MA007 76.07 18.72 24.23 2.56 0.00 0.00 92.27 213.85 92.98 18.91 31.88 3.37 0.00 0.00 118.79 265.93C85MA008 50.94 11.45 21.96 2.13 0.00 0.00 55.32 141.80 63.68 11.57 28.90 2.80 0.00 0.00 73.19 180.14C85TE001 33.27 6.67 13.26 1.99 0.00 0.00 38.38 93.57 40.94 6.75 17.34 2.60 0.00 0.00 52.76 120.39C85TE002 46.27 9.28 22.10 3.31 0.00 0.00 53.38 134.34 56.95 9.39 28.90 4.33 0.00 0.00 73.39 172.96C85TE003 51.75 11.61 29.61 2.87 0.00 0.00 66.69 162.53 62.10 11.72 38.73 3.75 0.00 0.00 88.49 204.79C85TE008 29.66 6.67 11.89 1.15 0.00 0.00 32.21 81.58 37.07 6.74 15.64 1.52 0.00 0.00 42.61 103.58C85TE009 36.55 8.22 14.86 1.44 0.00 0.00 39.69 100.76 45.69 8.30 19.55 1.89 0.00 0.00 52.51 127.94C85TE010 48.54 10.91 15.50 1.50 0.00 0.00 52.70 129.15 60.67 11.02 20.40 1.98 0.00 0.00 69.73 163.80C85TE011 65.09 16.02 20.35 2.15 0.00 0.00 78.96 182.57 79.56 16.18 26.78 2.83 0.00 0.00 101.65 227.00

C90C90LB001 61.28 15.45 25.00 2.87 12.75 1.99 75.08 194.42 68.09 15.52 31.49 3.62 51.00 7.96 88.04 265.72C90LB003 113.71 28.58 44.99 5.17 19.14 2.99 139.23 353.81 126.34 28.71 57.31 6.58 76.51 11.94 163.26 470.65

C95C95AP004 23.75 5.33 6.74 7.72 0.00 0.00 27.40 70.94C95AP005 0.76 0.17 0.00 0.00 0.00 0.00 0.87 1.80C95AP006 1.44 0.32 0.00 0.00 0.00 0.00 1.66 3.42C95AP007 37.50 8.41 11.21 11.18 0.00 0.00 43.26 111.56C95AP008 5.81 1.30 0.00 0.50 0.00 0.00 6.70 14.31C95AP009 1.93 0.43 0.00 0.00 0.00 0.00 2.23 4.59C95AP010 50.14 11.25 11.43 11.30 0.00 0.00 57.85 141.97C95AP011 1.81 0.41 0.00 0.00 0.00 0.00 2.08 4.30C95AP012 7.24 1.62 0.00 0.50 0.00 0.00 8.35 17.71C95AP013 47.81 10.72 18.64 15.27 0.00 0.00 55.16 147.60C95AP014 1.64 0.37 0.00 0.00 0.00 0.00 1.90 3.91C95AP015 6.31 1.42 0.00 0.50 0.00 0.00 7.29 15.52C95AP016 2.21 0.50 0.00 0.00 0.00 0.00 2.55 5.26

2 214

EP 1110-1-8, Vol. 430 Nov 11

2-272


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

C95 cont.C95AP017 20.21 4.53 6.58 6.63 0.00 0.00 23.32 61.27C95AP018 0.69 0.15 0.00 0.00 0.00 0.00 0.79 1.63C95AP019 3.93 0.88 0.00 0.50 0.00 0.00 4.53 9.84C95AP020 22.31 5.00 11.74 9.47 0.00 0.00 25.75 74.27C95AP021 34.97 7.84 13.58 11.49 0.00 0.00 40.34 108.22C95AP022 5.32 1.19 1.26 1.69 0.00 0.00 6.14 15.60C95AP023 0.13 0.03 0.00 0.00 0.00 0.00 0.14 0.30C95LH003 20.69 4.64 5.74 6.16 0.00 0.00 23.87 61.10C95LH005 26.93 6.04 7.79 8.29 0.00 0.00 31.07 80.12C95LH011 50.30 11.28 11.74 11.47 0.00 0.00 58.03 142.82C95LH013 64.21 14.40 11.74 11.47 0.00 0.00 74.08 175.90C95LH015 85.57 19.19 16.69 16.20 0.00 0.00 98.73 236.38C95LH022 18.16 4.11 1.84 3.01 0.64 0.10 20.99 48.85

D10D10IR003 9.80 1.91 0.00 0.79 0.00 0.00 14.32 26.82D10IR005 36.91 5.25 27.78 3.43 0.00 0.00 53.93 127.30D10SU002 12.07 2.36 0.00 0.80 0.00 0.00 17.63 32.86D10SU003 12.36 2.41 0.00 0.80 0.00 0.00 18.06 33.63D10SU005 18.80 2.67 33.59 4.15 0.00 0.00 27.47 86.68D10SU006 19.03 2.71 33.59 4.15 0.00 0.00 27.80 87.28

D15D15BI001 1.27 0.18 3.12 0.44 0.00 0.00 1.67 6.68D15BI002 2.28 0.32 2.58 0.32 0.00 0.00 3.00 8.50D15BI003 3.45 0.49 3.88 0.48 0.00 0.00 4.54 12.84D15BI004 5.37 0.76 5.81 0.72 0.00 0.00 7.07 19.73D15BI005 6.91 0.98 8.01 0.99 0.00 0.00 9.10 25.99

2 215

EP 1110-1-8, Vol. 430 Nov 11

2-273


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)11/30/2011

4REGION

D15 cont.D15BI006 11.59 1.65 15.37 1.90 0.00 0.00 15.26 45.77D15BI007 15.36 2.19 24.42 3.02 0.00 0.00 20.22 65.21D15BI008 14.32 2.04 24.42 3.02 0.00 0.00 18.85 62.65D15VE001 3.63 0.52 3.36 0.42 0.00 0.00 4.78 12.71D15VE002 6.21 0.88 6.07 0.75 0.00 0.00 8.17 22.08D15VE003 8.70 1.24 8.14 1.01 0.00 0.00 11.44 30.53D15VE004 10.78 1.53 10.72 1.32 0.00 0.00 14.19 38.54D15VE005 30.76 4.37 16.15 2.00 0.00 0.00 40.48 93.76D15VE006 22.61 3.22 18.09 2.24 0.00 0.00 29.76 75.92D15VE007 38.64 5.50 25.84 3.19 0.00 0.00 50.85 124.02D15VE008 43.10 6.13 29.07 3.59 0.00 0.00 56.72 138.61D15VE009 0.51 0.07 1.43 0.20 0.00 0.00 0.67 2.88D15VE010 1.50 0.21 2.84 0.35 0.00 0.00 1.97 6.87D15VE011 1.52 0.22 2.84 0.35 0.00 0.00 2.00 6.93D15VE012 3.15 0.45 3.55 0.44 0.00 0.00 4.14 11.73D15XX001 0.70 0.10 0.00 0.00 0.00 0.00 0.92 1.72D15XX002 1.05 0.15 0.00 0.00 0.00 0.00 1.39 2.59

D20D20AD007 1.57 0.18 0.52 1.06 0.00 0.00 1.96 5.29D20CQ001 1.48 0.17 4.16 1.79 0.00 0.00 1.83 9.43

D25D25AD003 9.85 1.40 8.91 0.94 0.00 0.00 14.40 35.50D25AD004 6.35 0.90 3.62 0.38 0.00 0.00 9.28 20.53D25EZ001 0.64 0.09 0.00 0.50 0.00 0.00 0.94 2.17D25EZ002 0.51 0.08 0.00 0.50 0.10 0.02 0.77 1.98D25EZ003 0.58 0.09 0.00 0.50 0.07 0.01 0.86 2.11

2 216

EP 1110-1-8, Vol. 430 Nov 11

2-274


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

D25 cont.D25EZ005 2.16 0.32 0.00 1.25 0.13 0.02 3.18 7.06

D30D30HD001 6.50 0.93 27.13 5.35 0.00 0.00 9.51 49.42D30HD002 9.75 1.39 34.88 7.31 0.00 0.00 14.25 67.58D30HD003 12.70 1.81 43.28 9.35 0.00 0.00 18.55 85.69D30MR001 1.06 0.15 2.08 0.29 0.00 0.00 1.55 5.13D30MR003 7.10 1.02 7.49 0.93 0.14 0.02 10.41 27.11D30MR005 17.06 2.46 17.41 2.15 0.49 0.08 25.02 64.67D30MR006 17.58 2.53 19.93 2.47 0.49 0.08 25.78 68.86D30MR007 22.27 3.20 19.93 2.47 0.49 0.08 32.63 81.07

D35D35DT001 44.43 7.85 58.14 9.75 0.00 0.00 60.87 181.04D35DT002 45.62 8.06 58.14 9.75 0.00 0.00 62.50 184.07D35DT003 51.33 9.07 58.14 9.75 0.00 0.00 70.32 198.61D35DT004 54.44 9.62 67.83 11.37 0.00 0.00 74.58 217.84D35DT005 84.79 14.98 98.19 16.46 0.00 0.00 116.16 330.58D35DT006 57.52 12.90 98.19 13.85 0.00 0.00 78.80 261.26D35IB003 33.00 7.45 68.78 9.69 0.85 0.13 45.27 165.17D35IB004 31.40 7.10 67.49 9.51 1.04 0.16 43.10 159.80D35IB005 36.45 8.23 81.70 11.52 1.04 0.16 50.00 189.10D35IB006 38.33 8.66 83.47 11.77 1.04 0.16 52.59 196.02D35RD001 28.94 5.11 58.51 9.81 0.00 0.00 39.64 142.01

F10F10JC001 5.72 0.77 7.91 0.84 0.94 0.15 5.95 22.28F10JC002 6.25 0.84 7.91 0.84 0.94 0.15 6.49 23.42

2 217

EP 1110-1-8, Vol. 430 Nov 11

2-275


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)11/30/2011

4REGION

G10G10CA012 3.36 0.36 33.10 3.50 0.00 0.00 2.96 43.28 4.21 0.37 43.77 4.62 0.00 0.00 4.23 57.20G10CA013 4.40 0.47 42.69 4.51 0.00 0.00 3.88 55.95 5.51 0.48 56.46 5.97 0.00 0.00 5.54 73.96G10CA014 6.00 0.64 56.49 5.97 0.00 0.00 5.28 74.38 7.51 0.66 74.72 7.90 0.00 0.00 7.55 98.34G10CA015 7.98 0.85 72.41 7.65 0.00 0.00 7.02 95.91 9.97 0.87 95.77 10.12 0.00 0.00 10.03 126.76G10CA016 9.76 1.04 86.11 9.10 0.00 0.00 8.59 114.60 12.20 1.07 113.89 12.03 0.00 0.00 12.26 151.45G10CA017 21.98 2.35 105.40 11.14 0.00 0.00 19.34 160.21 27.47 2.41 139.40 14.73 0.00 0.00 27.62 211.63G10CA018 25.83 2.77 232.51 24.57 0.00 0.00 22.73 308.41 32.29 2.83 307.52 32.49 0.00 0.00 32.47 407.60G10CA019 37.30 3.99 242.84 25.66 0.00 0.00 32.82 342.61 46.63 4.09 321.18 33.94 0.00 0.00 46.88 452.72G10CA020 2.72 0.29 18.34 1.94 0.00 0.00 2.39 25.68 3.40 0.30 24.26 2.56 0.00 0.00 3.41 33.93G10WC001 0.27 0.02 1.70 0.18 0.00 0.00 0.21 2.38 0.31 0.02 2.22 0.23 0.00 0.00 0.28 3.06G10WC002 0.32 0.03 2.34 0.25 0.00 0.00 0.24 3.18 0.36 0.03 3.06 0.32 0.00 0.00 0.32 4.09G10WC003 0.59 0.05 3.41 0.36 0.00 0.00 0.44 4.85 0.67 0.05 4.45 0.47 0.00 0.00 0.59 6.23G10WC004 0.48 0.04 3.83 0.40 0.00 0.00 0.36 5.11 0.55 0.04 5.00 0.53 0.00 0.00 0.48 6.60G10XX001 0.12 0.01 0.21 0.02 0.00 0.00 0.09 0.45 0.14 0.01 0.28 0.03 0.00 0.00 0.12 0.58G10XX002 0.61 0.05 4.05 0.43 0.00 0.00 0.46 5.60 0.69 0.05 5.28 0.56 0.00 0.00 0.61 7.19G10XX003 1.38 0.12 2.42 0.26 0.00 0.00 1.04 5.22 1.58 0.12 3.21 0.34 0.00 0.00 1.39 6.64G10XX004 0.71 0.06 0.95 0.10 0.00 0.00 0.54 2.36 0.81 0.06 1.25 0.13 0.00 0.00 0.72 2.97G10XX005 1.74 0.19 7.67 0.81 0.00 0.00 1.53 11.94 2.18 0.19 10.01 1.06 0.00 0.00 2.19 15.63G10XX006 1.53 0.16 10.65 1.13 0.00 0.00 1.35 14.82 1.91 0.17 13.90 1.47 0.00 0.00 1.93 19.38G10XX007 2.31 0.25 14.91 1.58 0.00 0.00 2.03 21.08 2.89 0.25 19.46 2.06 0.00 0.00 2.90 27.56G10XX008 2.83 0.30 11.28 1.19 0.00 0.00 2.49 18.09 3.53 0.31 14.92 1.58 0.00 0.00 3.55 23.89G10XX009 2.43 0.26 15.07 1.59 0.00 0.00 2.13 21.48 3.03 0.27 19.93 2.11 0.00 0.00 3.05 28.39G10XX010 3.61 0.39 21.08 2.23 0.00 0.00 3.18 30.49 4.51 0.40 27.88 2.95 0.00 0.00 4.54 40.28G10XX011 3.97 0.42 39.53 4.18 0.00 0.00 3.49 51.59 4.96 0.43 52.28 5.52 0.00 0.00 4.99 68.18G10XX012 4.70 0.50 45.11 4.77 0.00 0.00 4.14 59.22 5.88 0.52 59.66 6.30 0.00 0.00 5.91 78.27G10XX013 5.88 0.63 60.08 6.35 0.00 0.00 5.18 78.12 7.35 0.64 79.46 8.40 0.00 0.00 7.39 103.24G10XX014 8.46 0.91 75.15 7.94 0.00 0.00 7.44 99.90 10.57 0.93 99.39 10.50 0.00 0.00 10.63 132.02

2 218

EP 1110-1-8, Vol. 430 Nov 11

2-276


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

G10 cont.G10XX015 13.95 1.49 110.67 11.69 0.00 0.00 12.28 150.08 17.44 1.53 146.37 15.47 0.00 0.00 17.54 198.35G10XX016 19.74 2.11 150.20 15.87 0.00 0.00 17.37 205.29 24.67 2.16 198.65 20.99 0.00 0.00 24.81 271.28

G15G15CA001 14.93 3.04 13.61 2.04 0.98 0.15 16.83 51.58 16.04 3.05 17.36 2.60 3.25 0.51 20.49 63.30G15CA003 13.84 2.82 15.58 2.33 0.98 0.15 15.60 51.30 14.87 2.83 19.88 2.98 3.25 0.51 19.00 63.32G15CA004 14.81 3.11 18.04 2.70 4.29 0.67 16.82 60.44 15.91 3.12 23.02 3.45 14.17 2.21 20.48 82.36G15CA005 22.68 4.70 25.54 3.82 4.29 0.67 25.66 87.36 24.36 4.72 32.58 4.88 14.17 2.21 31.25 114.17G15CA006 34.50 7.11 29.28 4.39 5.66 0.88 38.98 120.80 37.06 7.13 37.36 5.60 18.67 2.91 47.47 156.20G15CA007 12.61 2.57 13.31 1.99 0.98 0.15 14.21 45.82 13.54 2.58 16.98 2.54 3.25 0.51 17.31 56.71G15CA008 16.87 3.53 18.24 2.73 4.86 0.76 19.14 66.13 18.12 3.54 23.27 3.48 16.40 2.56 23.31 90.68G15CA009 16.44 3.44 21.00 3.15 4.29 0.67 18.65 67.64 17.66 3.45 26.80 4.01 14.17 2.21 22.71 91.01G15CA010 18.30 3.82 19.72 2.95 4.86 0.76 20.74 71.15 19.66 3.83 25.16 3.77 16.40 2.56 25.26 96.64G15JD008 12.48 2.65 14.89 2.23 4.47 0.70 14.20 51.62 13.40 2.66 19.00 2.85 14.76 2.30 17.30 72.27G15JD009 14.47 3.05 15.38 2.30 5.06 0.79 16.44 57.49 15.54 3.06 19.62 2.94 17.08 2.66 20.02 80.92G15JD010 14.52 3.06 18.24 2.73 4.47 0.70 16.50 60.22 15.60 3.07 23.27 3.48 14.76 2.30 20.10 82.58G15JD011 16.49 3.46 20.21 3.03 5.06 0.79 18.71 67.75 17.71 3.47 25.79 3.86 17.08 2.66 22.79 93.36

H10H10NP001 1.03 0.08 0.00 0.50 0.00 0.00 1.41 3.02H10NP002 1.14 0.09 0.00 0.50 0.00 0.00 1.57 3.30H10NP003 1.71 0.14 0.00 0.75 0.00 0.00 2.35 4.95H10NP004 2.20 0.18 0.00 0.75 0.00 0.00 3.02 6.15H10NP005 2.91 0.24 0.00 1.00 0.00 0.00 4.00 8.15H10NP006 3.92 0.32 0.00 1.00 0.00 0.00 5.38 10.62H10NP008 5.95 0.48 0.00 1.25 0.00 0.00 8.16 15.84H10NP009 7.59 0.62 0.00 1.25 0.00 0.00 10.42 19.88H10NP015 9.24 0.75 0.00 1.25 0.00 0.00 12.69 23.93

2 219

EP 1110-1-8, Vol. 430 Nov 11

2-277


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)11/30/2011

4REGION

H10 cont.H10NP016 12.74 1.04 0.00 1.25 0.00 0.00 17.49 32.52H10NP017 16.64 1.35 0.00 1.25 0.00 0.00 22.83 42.07H10NP018 38.62 3.14 0.00 1.25 0.00 0.00 53.00 96.01

H13H13AY007 15.07 1.94 0.00 0.00 0.00 0.00 18.61 35.62H13AY008 7.40 0.95 0.00 0.00 0.00 0.00 9.14 17.49H13AY009 13.40 1.73 0.00 0.00 0.00 0.00 16.55 31.68H13AY010 6.83 0.88 0.00 0.00 0.00 0.00 8.43 16.14H13AY011 11.21 1.45 0.00 0.00 0.00 0.00 13.84 26.50H13AY012 5.73 0.74 0.00 0.00 0.00 0.00 7.08 13.55H13AY013 8.99 1.16 0.00 0.00 0.00 0.00 11.11 21.26H13AY014 4.83 0.62 0.00 0.00 0.00 0.00 5.96 11.41H13AY015 5.30 0.68 0.00 0.00 0.00 0.00 6.54 12.52H13AY016 3.43 0.44 0.00 0.00 0.00 0.00 4.24 8.11H13AY017 16.74 2.16 0.00 0.00 0.00 0.00 20.67 39.57H13AY018 8.52 1.10 0.00 0.00 0.00 0.00 10.52 20.14H13AY019 1.10 0.14 0.05 0.28 0.00 0.00 1.35 2.92H13AY020 1.42 0.18 0.05 0.28 0.00 0.00 1.75 3.68H13AY021 18.95 2.25 0.00 0.00 0.53 0.08 19.63 41.44H13AY022 10.22 1.22 0.00 0.00 0.53 0.08 10.60 22.65H13AY023 17.21 2.04 0.00 0.00 0.53 0.08 17.83 37.69H13AY024 9.06 1.09 0.00 0.00 0.53 0.08 9.40 20.16H13AY025 15.33 1.82 0.00 0.00 0.53 0.08 15.88 33.64H13AY026 8.34 1.00 0.00 0.00 0.53 0.08 8.65 18.60H13AY027 12.88 1.54 0.00 0.00 0.53 0.08 13.35 28.38H13AY028 7.06 0.85 0.00 0.00 0.53 0.08 7.33 15.85H13AY029 10.41 1.25 0.00 0.00 0.53 0.08 10.80 23.07

2 220

EP 1110-1-8, Vol. 430 Nov 11

2-278


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

H13 cont.H13AY030 5.99 0.73 0.00 0.00 0.53 0.08 6.22 13.55H13AY031 6.80 0.82 0.00 0.00 0.53 0.08 7.07 15.30H13AY032 4.48 0.55 0.00 0.00 0.53 0.08 4.66 10.30H13BB001 3.22 0.17 0.53 1.01 0.00 0.00 4.16 9.09H13BB002 4.12 0.22 0.79 1.39 0.00 0.00 5.32 11.84H13BC003 4.77 0.27 0.26 0.14 0.00 0.00 4.58 10.02H13BC006 3.45 0.20 0.16 0.09 0.00 0.00 3.32 7.22H13BC007 5.68 0.33 0.16 0.09 0.00 0.00 5.46 11.72H13BC008 6.55 0.38 0.26 0.14 0.00 0.00 6.29 13.62H13BC009 4.91 0.28 0.16 0.09 0.00 0.00 4.72 10.16H13BC010 2.80 0.16 0.16 0.09 0.00 0.00 2.69 5.90H13BC011 4.34 0.25 0.26 0.14 0.00 0.00 4.17 9.16H13BC012 3.55 0.20 0.16 0.09 0.00 0.00 3.41 7.41H13BC013 3.21 0.19 0.16 0.09 0.00 0.00 3.09 6.74H13CB001 2.15 0.25 0.26 0.39 0.00 0.00 2.22 5.27H13CB002 2.32 0.27 0.53 0.54 0.00 0.00 2.40 6.06H13CO002 1.00 0.12 0.26 0.39 0.00 0.00 1.04 2.81H13CO003 1.68 0.26 0.16 0.34 0.00 0.00 2.07 4.51H13CO004 2.47 0.38 0.16 0.59 0.00 0.00 3.05 6.65H13CO005 4.30 0.66 0.16 0.59 0.00 0.00 5.31 11.02H13CO006 3.61 0.55 0.16 0.44 0.00 0.00 4.45 9.21H13EP001 2.53 0.30 0.26 0.39 0.00 0.00 2.62 6.10H13EP002 2.60 0.40 0.39 0.52 0.00 0.00 3.21 7.12H13KP001 7.31 0.86 0.66 0.36 0.13 0.02 7.57 16.91H13KP002 8.30 0.98 0.82 0.45 0.13 0.02 8.59 19.29H13KP003 9.77 1.15 1.16 0.64 0.13 0.02 10.11 22.98H13KP004 11.24 1.33 1.47 0.81 0.13 0.02 11.63 26.63

2 221

EP 1110-1-8, Vol. 430 Nov 11

2-279


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)11/30/2011

4REGION

H13 cont.H13MN001 31.06 3.69 7.90 6.92 0.53 0.08 36.16 86.34H13MN002 36.26 4.32 10.53 9.22 0.77 0.12 42.23 103.45H13MN003 41.15 4.89 10.53 10.22 0.77 0.12 47.92 115.60H13MN004 47.03 5.58 15.80 13.84 0.77 0.12 54.75 137.89H13PR001 8.42 1.09 0.16 0.09 0.00 0.00 10.39 20.15H13PR002 24.96 2.96 0.16 1.59 0.53 0.08 25.84 56.12H13PR003 14.91 1.92 0.26 0.14 0.00 0.00 18.41 35.64H13PR005 19.68 2.54 0.26 0.14 0.00 0.00 24.31 46.93H13PR006 22.03 2.61 0.26 1.64 0.53 0.08 22.81 49.96H13PR007 23.81 3.07 0.53 0.29 0.00 0.00 29.40 57.10H13PR011 34.55 4.08 0.11 1.56 0.53 0.08 35.76 76.67H13PR012 37.16 4.39 0.16 1.59 0.53 0.08 38.46 82.37H13PR013 39.44 4.66 0.26 1.64 0.53 0.08 40.82 87.43H13PR014 44.31 5.23 0.42 1.73 0.53 0.08 45.85 98.15H13PR015 50.51 5.96 0.42 1.73 0.53 0.08 52.26 111.49H13PR022 17.41 2.24 0.11 0.06 0.00 0.00 21.50 41.32H13PR023 19.91 2.57 0.16 0.09 0.00 0.00 24.59 47.32H13PR024 22.08 2.85 0.16 0.09 0.00 0.00 27.26 52.44H13PR025 26.65 3.44 0.16 0.09 0.00 0.00 32.92 63.26H13PR026 32.49 4.19 0.21 0.12 0.00 0.00 40.12 77.13H13S5001 5.01 0.59 0.16 0.09 0.00 0.00 5.18 11.03H13S5002 7.85 0.92 0.26 0.14 0.00 0.00 8.12 17.29H13S5003 9.32 1.10 0.26 0.14 0.00 0.00 9.64 20.46H13SH001 4.85 0.57 1.05 0.52 0.00 0.00 5.64 12.63H13SH002 4.55 0.53 1.05 0.52 0.00 0.00 5.29 11.94H13SH003 7.83 0.92 2.11 1.05 0.00 0.00 9.10 21.01H13SH004 8.17 0.96 2.11 1.05 0.00 0.00 9.50 21.79

2 222

EP 1110-1-8, Vol. 430 Nov 11

2-280


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

H13 cont.H13SH005 13.09 1.54 5.27 2.61 0.00 0.00 15.21 37.72H13SH006 42.07 4.94 15.80 7.84 0.00 0.00 48.90 119.55H13SH007 54.78 6.43 31.59 15.67 0.00 0.00 63.68 172.15H13TH001 1.19 0.14 0.26 0.14 0.00 0.00 1.23 2.96H13TH002 2.20 0.26 0.95 0.10 0.06 0.01 2.28 5.86H13TH003 2.49 0.30 0.95 0.10 0.06 0.01 2.58 6.49H13YB001 32.95 3.87 2.63 1.45 0.00 0.00 34.07 74.97H13YB002 32.95 3.87 2.63 1.45 0.00 0.00 34.07 74.97H13YB003 32.95 3.87 2.63 1.45 0.00 0.00 34.07 74.97

H20H20BE002 3.62 0.42 0.00 0.20 0.00 0.00 3.98 8.22H20BE003 4.48 0.53 0.00 0.30 0.00 0.00 4.93 10.24H20BE004 4.92 0.58 0.00 0.40 0.00 0.00 5.40 11.30

H25H25AX001 1.14 0.08 0.00 0.00 0.00 0.00 1.47 2.69H25AX002 1.29 0.10 0.00 0.00 0.00 0.00 1.67 3.06H25AX003 1.41 0.11 0.00 0.00 0.00 0.00 1.82 3.34H25AX004 1.65 0.12 0.00 0.00 0.00 0.00 2.13 3.90H25AX005 1.67 0.12 0.00 0.00 0.00 0.00 2.16 3.95H25AX006 2.11 0.16 0.00 0.00 0.00 0.00 2.72 4.99H25BS001 0.93 0.08 0.00 0.00 0.00 0.00 1.02 2.03H25BS002 0.94 0.08 0.00 0.00 0.00 0.00 1.03 2.05H25BS003 1.23 0.10 0.00 0.00 0.00 0.00 1.35 2.68H25BS004 1.63 0.13 0.00 0.00 0.00 0.00 1.80 3.56H25BS005 2.21 0.18 0.00 0.00 0.00 0.00 2.43 4.82H25CA020 11.65 1.43 8.33 1.29 0.00 0.00 11.80 34.50 14.15 1.45 11.01 1.71 0.00 0.00 17.41 45.73

2 223

EP 1110-1-8, Vol. 430 Nov 11

2-281


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)11/30/2011

4REGION

H25 cont.H25CA021 11.72 1.44 8.85 1.37 0.00 0.00 11.87 35.25 14.23 1.46 11.71 1.81 0.00 0.00 17.51 46.72H25CA022 13.37 2.26 13.49 2.09 0.00 0.00 15.50 46.71 16.05 2.28 17.84 2.76 0.00 0.00 22.06 60.99H25CA023 19.34 3.26 13.49 2.09 0.00 0.00 22.41 60.59 23.20 3.30 17.84 2.76 0.00 0.00 31.90 79.00H25CA034 3.57 0.41 1.90 0.29 0.00 0.00 3.62 9.79 4.08 0.42 2.51 0.39 0.00 0.00 4.73 12.13H25CA035 4.18 0.48 3.16 0.49 0.00 0.00 4.23 12.54 4.78 0.49 4.18 0.65 0.00 0.00 5.53 15.63H25CA036 6.72 0.78 4.95 0.77 0.00 0.00 6.81 20.03 7.68 0.79 6.55 1.02 0.00 0.00 8.89 24.93H25CA038 9.10 1.11 5.69 0.88 0.00 0.00 9.22 26.00 11.05 1.13 7.53 1.17 0.00 0.00 13.60 34.48H25CA040 8.94 1.51 13.18 2.04 0.00 0.00 10.36 36.03 10.73 1.53 17.43 2.70 0.00 0.00 14.75 47.14H25CA052 15.30 1.14 0.00 1.50 0.00 0.00 17.79 35.73H25CA053 20.77 1.55 0.00 1.60 0.00 0.00 24.14 48.06H25CA054 26.70 1.99 0.00 3.00 0.00 0.00 31.04 62.73H25CA055 2.92 0.22 0.00 0.40 0.00 0.00 3.39 6.93H25CA056 43.55 3.24 0.00 3.00 0.00 0.00 50.62 100.41H25CA057 12.24 0.91 0.00 0.80 0.00 0.00 14.22 28.17H25CA058 3.24 0.24 0.00 0.50 0.00 0.00 4.19 8.17H25CA059 11.83 0.88 0.00 0.60 0.00 0.00 15.28 28.59H25CA060 17.42 1.30 0.00 0.75 0.00 0.00 22.51 41.98H25CA061 15.21 1.13 0.00 0.75 0.00 0.00 19.64 36.73H25CA062 27.86 2.07 0.00 0.90 0.00 0.00 35.99 66.82H25CA063 19.91 1.48 0.00 0.90 0.00 0.00 25.72 48.01H25CA064 24.22 1.80 0.00 1.00 0.00 0.00 31.29 58.31H25KC016 14.16 1.73 9.91 1.54 0.00 0.00 14.34 41.68 17.19 1.76 13.10 2.03 0.00 0.00 21.15 55.23H25KC017 9.97 1.22 5.69 0.88 0.00 0.00 10.10 27.86 12.11 1.24 7.53 1.17 0.00 0.00 14.90 36.95H25KC019 15.62 2.63 15.07 2.34 0.00 0.00 18.10 53.76 18.75 2.67 19.93 3.09 0.00 0.00 25.77 70.21H25KC020 17.16 2.89 15.07 2.34 0.00 0.00 19.88 57.34 20.59 2.93 19.93 3.09 0.00 0.00 28.30 74.84H25KC021 18.15 3.06 18.55 2.87 0.00 0.00 21.03 63.66 21.78 3.10 24.53 3.80 0.00 0.00 29.94 83.15H25KC022 20.55 3.47 18.55 2.87 0.00 0.00 23.82 69.26 24.66 3.51 24.53 3.80 0.00 0.00 33.91 90.41

2 224

EP 1110-1-8, Vol. 430 Nov 11

2-282


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

H25 cont.H25KC023 25.58 4.31 25.09 3.89 0.00 0.00 29.64 88.51 30.70 4.37 33.18 5.14 0.00 0.00 42.20 115.59H25KC024 24.21 5.37 32.25 1.58 0.00 0.00 35.06 98.47 28.70 5.41 42.66 2.09 0.00 0.00 45.68 124.54H25KC026 25.37 5.63 33.20 1.62 0.00 0.00 36.73 102.55 30.06 5.67 43.91 2.15 0.00 0.00 47.86 129.65H25KM001 12.49 1.53 9.38 1.45 0.00 0.00 12.66 37.51 15.17 1.56 12.41 1.92 0.00 0.00 18.66 49.72H25KM003 17.18 2.10 11.59 1.80 0.00 0.00 17.41 50.08 20.86 2.14 15.33 2.38 0.00 0.00 25.67 66.38H25KM009 37.70 9.85 47.85 2.54 0.00 0.00 60.01 157.95 47.75 9.96 63.29 3.36 0.00 0.00 86.40 210.76H25KM015 30.53 6.77 40.47 1.98 0.00 0.00 44.20 123.95 36.18 6.82 53.53 2.62 0.00 0.00 57.60 156.75H25KM018 4.55 0.53 2.11 0.33 0.00 0.00 4.61 12.13 5.20 0.53 2.79 0.43 0.00 0.00 6.03 14.98H25KM021 6.13 0.71 4.11 0.64 0.00 0.00 6.21 17.80 7.00 0.72 5.44 0.84 0.00 0.00 8.11 22.11H25KM022 7.83 0.91 4.22 0.65 0.00 0.00 7.94 21.55 8.95 0.92 5.58 0.86 0.00 0.00 10.37 26.68H25KM023 9.65 1.12 5.69 0.88 0.00 0.00 9.78 27.12 11.03 1.13 7.53 1.17 0.00 0.00 12.78 33.64H25KM027 17.65 2.16 9.06 1.40 0.00 0.00 17.89 48.16 21.44 2.20 11.99 1.86 0.00 0.00 26.38 63.87H25KM033 87.98 23.00 95.70 5.08 0.00 0.00 140.06 351.82 111.44 23.24 126.58 6.71 0.00 0.00 201.63 469.60H25KN001 4.28 0.32 0.00 0.50 0.00 0.00 5.53 10.63H25KN002 5.94 0.44 0.00 0.50 0.00 0.00 7.67 14.55H25KN003 7.24 0.54 0.00 0.50 0.00 0.00 9.35 17.63H25KN004 8.33 0.62 0.00 0.50 0.00 0.00 10.75 20.20H25KN006 16.81 1.25 0.00 1.00 0.00 0.00 21.71 40.77H25KN007 0.86 0.06 0.00 0.15 0.00 0.00 1.11 2.18H25KN009 1.79 0.13 0.00 0.15 0.00 0.00 2.31 4.38H25KN010 2.47 0.18 0.00 0.15 0.00 0.00 3.19 5.99H25LB003 14.07 1.72 10.01 1.55 0.00 0.00 14.26 41.61 17.08 1.75 13.24 2.05 0.00 0.00 21.02 55.14H25LB005 16.47 2.02 12.65 1.96 0.00 0.00 16.69 49.79 20.00 2.05 16.73 2.59 0.00 0.00 24.62 65.99H25LU001 3.90 0.29 0.00 0.40 0.00 0.00 4.53 9.12H25LU002 4.39 0.33 0.00 0.50 0.00 0.00 5.10 10.32H25LU003 6.78 0.50 0.00 0.80 0.00 0.00 7.88 15.96H25LU004 7.88 0.59 0.00 0.90 0.00 0.00 9.16 18.53

2 225

EP 1110-1-8, Vol. 430 Nov 11

2-283


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)11/30/2011

4REGION

H25 cont.H25LU005 9.88 0.73 0.00 1.10 0.00 0.00 11.48 23.19H25LU006 13.84 1.03 0.00 1.50 0.00 0.00 16.09 32.46H25LU007 11.80 0.88 0.00 1.40 0.00 0.00 13.72 27.80H25LU008 15.44 1.15 0.00 1.60 0.00 0.00 17.95 36.14H25LU009 16.94 1.26 0.00 1.70 0.00 0.00 19.70 39.60H25LU010 20.36 1.51 0.00 2.00 0.00 0.00 23.66 47.53H25LU011 20.16 1.50 0.00 2.00 0.00 0.00 23.44 47.10H25LU012 24.69 1.84 0.00 2.50 0.00 0.00 28.70 57.73H25LU013 25.51 1.90 0.00 2.60 0.00 0.00 29.65 59.66H25LU014 29.69 2.21 0.00 3.00 0.00 0.00 34.51 69.41H25LU023 5.05 0.41 0.00 0.25 0.00 0.00 5.55 11.26H25LU024 2.52 0.21 0.00 0.30 0.00 0.00 2.77 5.80H25LU025 3.09 0.25 0.00 0.40 0.00 0.00 3.39 7.13H25LU026 3.51 0.29 0.00 0.50 0.00 0.00 3.86 8.16H25LU027 3.93 0.32 0.00 0.60 0.00 0.00 4.32 9.17H25LU028 6.49 0.53 0.00 0.70 0.00 0.00 7.13 14.85H25LU034 9.47 0.77 0.00 0.80 0.00 0.00 10.41 21.45H25LU035 11.34 0.92 0.00 0.90 0.00 0.00 12.46 25.62H25LU036 13.06 1.06 0.00 1.00 0.00 0.00 14.35 29.47H25LU040 21.06 1.57 0.00 0.75 0.00 0.00 27.20 50.58H25LU041 25.83 1.92 0.00 0.75 0.00 0.00 33.37 61.87H25LU042 31.16 2.32 0.00 1.50 0.00 0.00 40.25 75.23H25LU046 5.01 0.37 0.00 0.50 0.00 0.00 6.47 12.35H25LU047 5.76 0.43 0.00 0.60 0.00 0.00 7.44 14.23H25LU048 6.17 0.46 0.00 0.70 0.00 0.00 7.98 15.31H25LU049 7.46 0.55 0.00 0.80 0.00 0.00 9.63 18.44H25LU050 11.29 0.84 0.00 0.90 0.00 0.00 14.58 27.61

2 226

EP 1110-1-8, Vol. 430 Nov 11

2-284


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

H25 cont.H25LU053 22.16 1.65 0.00 0.75 0.00 0.00 28.63 53.19H25LU054 27.29 2.03 0.00 0.75 0.00 0.00 35.25 65.32H25ME001 2.79 0.32 1.40 0.22 0.00 0.00 2.82 7.55 3.18 0.33 1.85 0.29 0.00 0.00 3.69 9.34H25ME002 4.00 0.46 4.22 0.65 0.00 0.00 4.05 13.38 4.57 0.47 5.58 0.86 0.00 0.00 5.29 16.77H25ME003 5.55 0.64 5.06 0.78 0.00 0.00 5.63 17.66 6.35 0.65 6.69 1.04 0.00 0.00 7.35 22.08H25WN001 1.03 0.08 0.00 0.00 0.00 0.00 1.14 2.25H25WN002 1.17 0.09 0.00 0.00 0.00 0.00 1.51 2.77H25WN003 1.28 0.10 0.00 0.00 0.00 0.00 1.66 3.04H25WN004 1.40 0.10 0.00 0.00 0.00 0.00 1.81 3.31H25WN005 1.59 0.12 0.00 0.00 0.00 0.00 2.06 3.77

H30H30CA005 18.41 2.20 14.89 2.18 1.62 0.25 13.43 52.98 22.66 2.24 19.00 2.79 5.85 0.91 18.18 71.63H30CA007 15.14 1.86 11.93 1.75 2.61 0.41 11.13 44.83 18.63 1.90 15.22 2.23 9.39 1.46 15.06 63.89H30GA006 27.33 3.23 22.97 3.37 1.53 0.24 19.89 78.56 33.63 3.30 29.31 4.30 5.44 0.85 26.92 103.75H30GA007 20.57 2.43 13.61 2.00 0.94 0.15 14.96 54.66 25.31 2.48 17.36 2.55 3.33 0.52 20.24 71.79H30GA008 24.00 3.57 20.56 3.02 6.08 0.95 21.07 79.25 30.01 3.63 25.89 3.80 21.52 3.36 28.56 116.77H30KM001 18.32 2.65 12.13 1.78 1.02 0.16 15.96 52.02 22.90 2.69 15.47 2.27 3.66 0.57 21.64 69.20

H35H35HI006 68.46 13.73 67.56 3.58 0.00 0.00 111.50 264.83 78.23 13.82 89.36 4.74 0.00 0.00 137.99 324.14H35OK001 53.92 10.82 63.98 3.39 0.00 0.00 87.82 219.93 61.62 10.89 84.62 4.49 0.00 0.00 108.69 270.31H35OK003 106.99 21.47 107.30 5.69 0.00 0.00 174.27 415.72 122.28 21.60 141.91 7.53 0.00 0.00 215.67 508.99H35OK004 177.96 35.71 134.91 7.16 0.00 0.00 289.86 645.60 203.39 35.93 178.43 9.46 0.00 0.00 358.73 785.94H35OK005 349.87 70.20 237.15 12.58 0.00 0.00 569.85 1,239.65 399.85 70.64 313.65 16.64 0.00 0.00 705.23 1,506.01

L10L10BS002 3.22 0.42 0.00 0.30 0.00 0.00 3.95 7.89 4.60 0.43 0.00 0.30 0.00 0.00 6.27 11.60

2 227

EP 1110-1-8, Vol. 430 Nov 11

2-285


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)11/30/2011

4REGION

L10 cont.L10BS004 2.19 0.28 0.00 0.25 0.00 0.00 2.69 5.41 3.13 0.29 0.00 0.25 0.00 0.00 4.27 7.94L10BS005 3.22 0.42 0.00 0.30 0.00 0.00 3.96 7.90 4.61 0.43 0.00 0.30 0.00 0.00 6.28 11.62L10BS007 2.33 0.30 0.00 0.50 0.00 0.00 2.86 5.99 3.32 0.31 0.00 0.50 0.00 0.00 4.53 8.66L10BU005 0.79 0.10 0.00 1.10 0.00 0.00 0.97 2.96 1.13 0.11 0.00 1.10 0.00 0.00 1.54 3.88L10BU010 0.33 0.04 0.00 0.80 0.00 0.00 0.40 1.57 0.47 0.04 0.00 0.80 0.00 0.00 0.64 1.95L10BU011 0.66 0.09 0.00 1.50 0.00 0.00 0.81 3.06 0.94 0.09 0.00 1.50 0.00 0.00 1.29 3.82L10BU012 1.35 0.17 0.00 2.00 0.00 0.00 1.66 5.18 1.93 0.18 0.00 2.00 0.00 0.00 2.64 6.75L10BU013 1.64 0.21 0.00 2.50 0.00 0.00 2.01 6.36 2.34 0.22 0.00 2.50 0.00 0.00 3.19 8.25L10RM001 4.29 0.55 0.00 0.40 0.00 0.00 5.26 10.50 6.13 0.57 0.00 0.40 0.00 0.00 8.36 15.46L10RM002 3.87 0.50 0.00 0.00 0.00 0.00 4.75 9.12 5.53 0.52 0.00 0.00 0.00 0.00 7.53 13.58L10VE002 1.93 0.25 6.82 0.90 0.08 0.01 2.37 12.36 2.75 0.26 8.84 1.17 0.25 0.04 3.77 17.08L10VE005 1.01 0.13 2.53 0.33 0.07 0.01 1.25 5.33 1.45 0.14 3.29 0.44 0.22 0.03 1.99 7.56L10VE006 2.70 0.35 3.90 0.52 0.07 0.01 3.32 10.87 3.86 0.36 5.05 0.67 0.22 0.03 5.27 15.46L10VE007 2.35 0.30 0.00 1.50 0.00 0.00 2.89 7.04 3.36 0.31 0.00 1.50 0.00 0.00 4.58 9.75L10VE009 3.05 0.40 7.69 0.88 0.07 0.01 3.75 15.85 4.36 0.41 9.81 1.13 0.22 0.03 5.95 21.91L10VE010 1.06 0.14 5.26 0.70 0.03 0.00 1.30 8.49 1.51 0.14 6.82 0.90 0.10 0.02 2.07 11.56

L15L15BW001 4.19 0.23 6.50 0.69 0.09 0.01 3.80 15.51L15BW002 7.68 0.42 9.10 0.96 0.18 0.03 6.97 25.34L15BW003 8.85 0.48 13.00 1.37 0.18 0.03 8.03 31.94L15BW004 13.13 0.70 11.63 1.23 0.00 0.00 11.88 38.57L15FG001 41.63 2.20 21.18 2.24 0.00 0.00 37.66 104.91L15FG002 9.43 0.51 14.86 1.57 0.13 0.02 8.55 35.07L15HV002 0.27 0.01 2.60 0.27 0.00 0.00 0.25 3.40L15HZ001 0.18 0.01 0.78 0.08 0.00 0.00 0.16 1.21L15JD001 1.53 0.13 5.20 0.55 1.97 0.31 1.51 11.20L15JD005 0.49 0.03 0.00 0.00 0.00 0.00 0.45 0.97

2 228

EP 1110-1-8, Vol. 430 Nov 11

2-286


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

L15 cont.L15JD006 0.92 0.05 0.00 0.00 0.00 0.00 0.83 1.80L15TO001 0.29 0.02 1.56 0.16 0.00 0.00 0.27 2.30L15TO002 0.82 0.05 3.90 0.41 0.18 0.03 0.75 6.14L15TO003 1.65 0.09 5.46 0.58 0.18 0.03 1.50 9.49L15TO004 1.77 0.10 5.46 0.58 0.15 0.02 1.61 9.69L15TO006 3.27 0.18 7.54 0.80 0.30 0.05 2.98 15.12L15TO007 3.38 0.19 7.54 0.80 0.30 0.05 3.08 15.34L15TO010 0.42 0.02 2.60 0.27 0.00 0.00 0.38 3.69L15WI001 1.75 0.10 0.00 0.05 0.12 0.02 1.59 3.63

L20L20AB017 1.39 0.15 1.87 0.20 0.06 0.01 2.88 6.56L20AB018 1.55 0.17 1.99 0.21 0.06 0.01 3.21 7.20L20AB019 1.82 0.19 1.99 0.21 0.06 0.01 3.77 8.05L20AB020 1.17 0.13 1.60 0.17 0.06 0.01 2.42 5.56L20AB021 1.24 0.13 1.99 0.21 0.06 0.01 2.56 6.20L20AB022 1.40 0.15 1.87 0.20 0.06 0.01 2.89 6.58L20AB023 0.57 0.06 0.00 0.00 0.04 0.01 1.18 1.86L20AB024 0.61 0.07 0.00 0.00 0.04 0.01 1.26 1.99

L25L25JE001 1.22 0.13 3.61 0.38 0.00 0.00 2.01 7.35L25JE002 10.25 1.09 32.06 3.39 0.36 0.06 16.93 64.14L25MB002 0.52 0.07 1.39 1.15 0.32 0.05 0.90 4.40L25MB004 15.97 1.70 52.81 7.08 0.36 0.06 26.35 104.33L25MB005 1.05 0.12 2.78 1.29 0.32 0.05 1.77 7.38L25MB006 9.79 1.03 16.68 3.01 0.00 0.00 16.12 46.63L25MB007 5.49 0.58 6.39 1.68 0.00 0.00 9.05 23.19

2 229

EP 1110-1-8, Vol. 430 Nov 11

2-287


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)11/30/2011

4REGION

L25 cont.L25MB008 17.20 1.85 26.49 4.30 1.02 0.16 28.47 79.49

L30L30HW015 11.65 1.54 1.32 0.65 0.81 0.13 16.07 32.17 14.56 1.57 1.72 0.85 2.56 0.40 22.10 43.76L30KB001 2.74 0.37 0.79 0.39 0.26 0.04 3.79 8.38 3.42 0.37 1.03 0.51 0.83 0.13 5.21 11.50L30KB002 2.89 0.39 0.79 0.39 0.26 0.04 3.99 8.75 3.61 0.39 1.03 0.51 0.83 0.13 5.49 11.99L30RA001 6.03 0.79 2.64 0.33 0.28 0.04 8.30 18.41 7.53 0.81 3.49 0.43 0.90 0.14 11.41 24.71L30S4001 1.56 0.20 0.79 0.39 0.00 0.00 2.14 5.08 1.95 0.20 1.03 0.51 0.00 0.00 2.94 6.63L30S4002 1.78 0.23 0.00 0.00 0.00 0.00 2.44 4.45 2.22 0.23 0.00 0.00 0.00 0.00 3.36 5.81L30S4003 0.13 0.02 0.00 0.00 0.00 0.00 0.18 0.33 0.16 0.02 0.00 0.00 0.00 0.00 0.25 0.43L30S4004 0.22 0.03 0.00 0.00 0.00 0.00 0.30 0.55 0.28 0.03 0.00 0.00 0.00 0.00 0.42 0.73L30TS001 2.98 0.41 0.63 0.31 0.62 0.10 4.15 9.20 3.72 0.42 0.83 0.41 1.95 0.30 5.70 13.33

L35L35CA005 16.99 2.19 17.11 1.80 0.00 0.00 25.48 63.57 21.23 2.23 22.14 2.33 0.00 0.00 36.20 84.13L35CA007 32.09 4.14 27.98 2.94 0.00 0.00 48.13 115.28 40.11 4.22 36.20 3.80 0.00 0.00 68.39 152.72L35CA013 10.32 1.33 10.40 1.09 0.00 0.00 15.49 38.63 12.91 1.36 13.46 1.41 0.00 0.00 22.01 51.15L35CA014 23.20 2.99 18.50 1.94 0.00 0.00 34.80 81.43 29.00 3.05 23.94 2.51 0.00 0.00 49.44 107.94L35KM006 37.67 4.86 23.12 2.43 0.00 0.00 56.51 124.59 47.09 4.96 29.92 3.14 0.00 0.00 80.29 165.40

L40L40CA007 27.63 5.02 36.78 3.06 13.26 2.07 26.72 114.54 31.08 5.06 48.65 4.05 47.73 7.45 32.19 176.21L40CA009 103.34 18.84 84.32 7.02 21.14 3.30 100.05 338.01 116.26 18.99 111.52 9.28 76.10 11.87 120.51 464.53L40CA012 14.35 2.08 15.28 1.76 1.64 0.26 17.83 53.20 15.51 2.10 20.21 2.33 5.90 0.92 20.42 67.39L40CA013 8.89 1.31 9.49 1.10 1.64 0.26 11.08 33.77 9.61 1.31 12.55 1.45 5.90 0.92 12.69 44.43L40CA014 20.04 2.90 21.08 2.43 1.98 0.31 24.88 73.62 21.66 2.92 27.88 3.22 7.11 1.11 28.49 92.39L40CA015 11.36 1.55 15.70 1.81 1.64 0.26 11.65 43.97 12.01 1.55 20.77 2.40 5.90 0.92 14.07 57.62L40CA018 76.12 13.65 66.09 5.50 11.48 1.79 73.43 248.06 85.64 13.75 87.40 7.27 41.34 6.45 88.45 330.30

2 230

EP 1110-1-8, Vol. 430 Nov 11

2-288


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

L40 cont.L40CA019 8.16 1.12 10.01 1.16 1.64 0.26 8.40 30.75 8.63 1.13 13.24 1.53 5.90 0.92 10.14 41.49L40CA022 11.46 1.56 13.49 1.56 1.64 0.26 11.75 41.72 12.11 1.57 17.84 2.06 5.90 0.92 14.20 54.60L40CA023 13.27 1.90 18.97 2.19 5.66 0.88 13.80 56.67 14.03 1.91 25.09 2.90 20.37 3.18 16.68 84.16L40CA024 16.81 2.40 20.76 2.40 6.77 1.06 17.47 67.67 17.78 2.41 27.46 3.17 24.36 3.80 21.10 100.08L40CA025 17.93 2.55 22.24 2.57 6.77 1.06 18.61 71.73 18.96 2.56 29.41 3.40 24.36 3.80 22.48 104.97L40CA028 3.09 0.34 5.66 0.65 0.75 0.12 3.40 14.01L40CA029 3.43 0.38 6.24 0.72 0.75 0.12 3.78 15.42L40CA030 3.87 0.43 6.82 0.79 0.97 0.15 4.27 17.30L40CA031 3.76 0.42 8.55 0.99 0.97 0.15 4.15 18.99L40CA032 3.74 0.52 5.48 0.63 0.65 0.10 3.86 14.98 3.96 0.52 7.25 0.84 2.34 0.37 4.67 19.95L40CA033 4.98 0.68 7.17 0.83 0.65 0.10 5.12 19.53 5.26 0.69 9.48 1.09 2.34 0.37 6.18 25.41L40CA034 5.32 0.80 8.01 0.92 4.76 0.74 5.61 26.16 5.63 0.80 10.59 1.22 17.14 2.67 6.78 44.83L40CA035 43.10 8.07 52.81 4.39 19.90 3.10 41.96 173.33 48.49 8.13 69.84 5.81 71.62 11.17 50.54 265.60L40CS009 12.16 1.74 14.33 1.65 5.18 0.81 12.64 48.51 12.85 1.75 18.96 2.19 18.64 2.91 15.27 72.57L40CS010 14.69 2.08 19.08 2.20 5.18 0.81 15.22 59.26 15.53 2.09 25.23 2.91 18.64 2.91 18.39 85.70L40CS011 18.51 2.63 19.71 2.28 6.77 1.06 19.19 70.15 19.57 2.64 26.07 3.01 24.36 3.80 23.18 102.63L40KM003 9.93 1.59 14.65 1.69 10.60 1.65 10.64 50.75 10.49 1.60 19.38 2.24 38.16 5.95 12.85 90.67L40KM008 19.20 3.58 35.31 2.94 8.49 1.32 18.68 89.52 21.60 3.61 46.70 3.89 30.55 4.77 22.50 133.62L40KM009 35.38 6.57 51.65 4.30 9.24 1.44 34.38 142.96 39.80 6.62 68.31 5.68 33.27 5.19 41.41 200.28L40KM010 48.53 8.94 72.09 6.00 11.48 1.79 47.08 195.91 54.59 9.01 95.35 7.93 41.34 6.45 56.71 271.38L40KM011 79.60 14.79 89.91 7.48 21.14 3.30 77.37 293.59 89.55 14.91 118.91 9.89 76.10 11.87 93.20 414.43L40KM015 7.07 0.98 7.91 0.91 1.07 0.17 7.29 25.40 7.47 0.98 10.46 1.21 3.84 0.60 8.80 33.36L40ME012 2.75 0.30 5.32 0.61 0.42 0.07 3.02 12.49L40ME016 1.67 0.18 2.72 0.31 0.38 0.06 1.83 7.15L40ME017 2.05 0.23 4.10 0.47 0.59 0.09 2.26 9.79L40ME021 2.23 0.26 5.66 0.65 1.30 0.20 2.49 12.79L40ME022 3.38 0.38 8.67 1.00 1.30 0.20 3.74 18.67

2 231

EP 1110-1-8, Vol. 430 Nov 11

2-289


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)11/30/2011

4REGION

L40 cont.L40ME023 3.78 0.42 9.36 1.08 1.30 0.20 4.18 20.32

L50L50CA001 4.56 0.69 6.36 2.92 0.86 0.13 5.39 20.91 7.61 0.72 9.02 4.14 3.03 0.47 9.54 34.53L50CA004 11.10 1.65 8.98 4.12 1.47 0.23 13.06 40.61 18.50 1.72 12.72 5.83 5.22 0.81 23.11 67.91L50CS005 7.03 1.04 7.34 3.37 0.91 0.14 8.27 28.10 11.72 1.09 10.40 4.77 3.26 0.51 14.64 46.39L50CS006 8.38 1.25 8.00 3.67 1.36 0.21 9.87 32.74 13.96 1.31 11.33 5.20 4.83 0.75 17.47 54.85L50JC001 5.33 0.79 5.47 2.51 0.70 0.11 6.26 21.17 8.89 0.82 7.75 3.55 2.52 0.39 11.09 35.01L50JC002 6.00 0.90 7.51 3.44 0.99 0.15 7.07 26.06 9.99 0.94 10.64 4.88 3.50 0.55 12.51 43.01L50JC003 7.26 1.09 8.16 3.74 1.42 0.22 8.56 30.45 12.09 1.14 11.56 5.30 5.10 0.80 15.16 51.15L50JC005 8.47 1.26 8.16 3.74 1.42 0.22 9.98 33.25 14.12 1.32 11.56 5.30 5.10 0.80 17.66 55.86L50JC007 10.88 1.61 8.16 3.74 1.63 0.25 12.80 39.07 18.14 1.69 11.56 5.30 5.87 0.92 22.66 66.14

L55L55KN001 0.97 0.08 0.00 0.52 0.00 0.00 1.33 2.90L55KN002 1.98 0.16 0.00 1.06 0.00 0.00 2.72 5.92L55KN004 1.83 0.15 0.00 0.00 0.00 0.00 2.52 4.50L55KN005 2.71 0.22 0.00 0.00 0.00 0.00 3.71 6.64L55KN006 4.03 0.33 0.00 0.00 0.00 0.00 5.53 9.89

L60L60CA010 30.95 3.63 15.81 1.95 0.00 0.00 27.92 80.26 38.68 3.71 20.91 2.58 0.00 0.00 39.91 105.79L60CA011 33.81 3.97 15.81 1.95 0.00 0.00 30.51 86.05 42.27 4.05 20.91 2.58 0.00 0.00 43.61 113.42L60CA013 27.47 3.34 16.86 2.08 2.69 0.42 24.91 77.77 34.34 3.40 22.30 2.76 9.39 1.46 35.61 109.26L60CA014 26.65 3.13 12.65 1.56 0.00 0.00 24.05 68.04 33.31 3.20 16.73 2.07 0.00 0.00 34.37 89.68L60JD001 13.32 1.69 12.54 1.55 3.63 0.57 12.16 45.46 16.65 1.72 16.59 2.05 13.08 2.04 17.38 69.51L60JD002 15.98 2.00 15.92 1.97 3.63 0.57 14.56 54.63 19.98 2.04 21.05 2.60 13.08 2.04 20.81 81.60L60JD003 12.97 1.64 12.54 1.55 3.63 0.57 11.85 44.75 16.22 1.68 16.59 2.05 13.08 2.04 16.93 68.59

2 232

EP 1110-1-8, Vol. 430 Nov 11

2-290


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

L60 cont.L60JD004 16.95 2.18 16.86 2.08 5.70 0.89 15.52 60.18 21.19 2.23 22.30 2.76 20.51 3.20 22.18 94.37L60JD006 21.07 2.64 17.92 2.21 4.85 0.76 19.19 68.64 26.33 2.69 23.70 2.93 17.45 2.72 27.43 103.25L60JD007 23.17 2.88 21.08 2.60 4.85 0.76 21.10 76.44 28.97 2.94 27.88 3.44 17.45 2.72 30.15 113.55L60JD008 32.27 3.79 17.92 2.21 0.00 0.00 29.12 85.31 40.33 3.87 23.70 2.93 0.00 0.00 41.61 112.44

M10M10MZ001 3.45 0.24 0.00 0.00 0.00 0.00 2.16 5.85M10MZ003 4.04 0.28 0.00 0.00 0.00 0.00 2.53 6.85M10MZ005 0.92 0.28 0.00 0.00 0.00 0.00 0.69 1.89M10MZ007 1.01 0.31 0.00 0.00 0.00 0.00 0.76 2.08M10MZ010 3.40 0.62 14.76 2.47 0.00 0.00 3.16 24.41 4.19 0.63 19.52 3.27 0.00 0.00 4.17 31.78M10MZ011 4.41 0.80 22.13 3.71 0.00 0.00 4.10 35.15 5.43 0.81 29.27 4.91 0.00 0.00 5.40 45.82M10SM001 4.17 0.76 31.95 4.51 0.00 0.00 3.88 45.27 5.14 0.77 41.70 5.88 0.00 0.00 5.11 58.60M10SM003 4.86 0.88 42.60 6.01 0.00 0.00 4.52 58.87 5.99 0.90 55.59 7.84 0.00 0.00 5.96 76.28M10SM004 5.11 0.93 53.25 7.51 0.00 0.00 4.75 71.55 6.29 0.94 69.49 9.80 0.00 0.00 6.26 92.78M10SM005 1.88 0.34 24.49 3.45 0.00 0.00 1.75 31.91 2.32 0.35 31.97 4.51 0.00 0.00 2.31 41.46M10SM008 3.30 0.60 42.60 6.01 0.00 0.00 3.07 55.58 4.06 0.61 55.59 7.84 0.00 0.00 4.04 72.14M10XX001 0.20 0.06 0.00 0.00 0.00 0.00 0.15 0.41M10XX002 0.62 0.19 0.00 0.00 0.00 0.00 0.47 1.28M10XX003 0.75 0.23 0.00 0.00 0.00 0.00 0.56 1.54M10XX004 1.21 0.37 0.00 0.00 0.00 0.00 0.91 2.49M10XX005 1.84 1.47 0.00 0.00 0.00 0.00 1.31 4.62M10XX006 2.59 2.07 0.00 0.00 0.00 0.00 1.85 6.51M10XX007 3.30 2.64 0.00 0.00 0.00 0.00 2.35 8.29M10XX008 4.58 3.66 0.00 0.00 0.00 0.00 3.26 11.50M10XX009 0.83 0.15 10.65 1.50 0.00 0.00 0.77 13.90 1.02 0.15 13.90 1.96 0.00 0.00 1.02 18.05M10XX010 2.77 0.50 7.91 1.33 0.00 0.00 2.58 15.09 3.42 0.51 10.46 1.75 0.00 0.00 3.40 19.54M10XX011 3.19 0.58 10.54 1.77 0.00 0.00 2.96 19.04 3.92 0.59 13.94 2.34 0.00 0.00 3.91 24.70

2 233

EP 1110-1-8, Vol. 430 Nov 11

2-291


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)11/30/2011

4REGION

M10 cont.M10XX012 3.25 0.59 10.54 1.77 0.00 0.00 3.02 19.17 4.00 0.60 13.94 2.34 0.00 0.00 3.98 24.86M10XX013 4.21 0.76 12.12 2.03 0.00 0.00 3.91 23.03 5.18 0.77 16.03 2.69 0.00 0.00 5.16 29.83M10XX014 5.79 1.05 18.45 3.09 0.00 0.00 5.38 33.76 7.12 1.07 24.40 4.09 0.00 0.00 7.09 43.77M10XX015 7.26 1.32 26.35 4.42 0.00 0.00 6.75 46.10 8.94 1.34 34.85 5.84 0.00 0.00 8.90 59.87M10XX016 8.26 2.26 0.00 0.00 0.00 0.00 6.87 17.39M10XX017 8.73 2.39 0.00 0.00 0.00 0.00 7.26 18.38M10XX018 10.88 2.97 0.00 0.00 0.00 0.00 9.04 22.89M10XX019 11.11 3.04 0.00 0.00 0.00 0.00 9.24 23.39M10XX021 18.13 3.35 40.05 6.71 0.00 0.00 18.19 86.43 21.75 3.38 52.97 8.88 0.00 0.00 23.18 110.16M10XX022 20.63 3.81 45.85 7.69 0.00 0.00 20.69 98.67 24.75 3.85 60.64 10.17 0.00 0.00 26.37 125.78M10XX023 27.63 5.10 42.16 7.07 0.00 0.00 27.72 109.68 33.15 5.16 55.76 9.35 0.00 0.00 35.32 138.74M10XX024 39.39 7.28 45.85 7.69 0.00 0.00 39.52 139.73 47.27 7.35 60.64 10.17 0.00 0.00 50.37 175.80

P10P10IC001 12.46 1.36 18.45 2.60 0.00 0.00 16.84 51.71P10IC002 19.61 2.13 31.62 4.46 0.00 0.00 26.52 84.34P10IC005 52.38 5.70 84.32 11.89 0.00 0.00 70.84 225.13P10IC010 1.84 0.20 0.00 0.00 0.00 0.00 2.48 4.52P10IC011 3.62 0.39 1.37 0.19 0.00 0.00 4.90 10.47P10IC012 2.59 0.28 0.00 0.00 0.00 0.00 3.50 6.37P10IC013 4.49 0.49 2.77 0.39 0.00 0.00 6.07 14.21

P20P20IC002 13.05 1.17 0.00 1.90 0.00 0.00 21.01 37.13P20IC003 13.26 1.19 0.00 2.50 0.00 0.00 21.36 38.31P20IC004 14.15 1.27 0.00 3.15 0.00 0.00 22.79 41.36P20MK002 3.51 0.29 0.00 0.50 0.00 0.00 5.30 9.60P20MK003 3.96 0.32 0.00 1.00 0.00 0.00 5.98 11.26

2 234

EP 1110-1-8, Vol. 430 Nov 11

2-292


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

P20 cont.P20MK004 5.56 0.45 0.00 1.25 0.00 0.00 8.39 15.65P20MK005 8.57 0.70 0.00 1.25 0.00 0.00 12.94 23.46P20MK006 11.65 0.95 0.00 2.50 0.00 0.00 17.58 32.68P20MK007 13.19 1.07 0.00 2.50 0.00 0.00 19.92 36.68

P25P25DL001 3.42 0.28 2.21 1.26 0.00 0.00 4.69 11.86P25DL003 4.42 0.36 5.69 2.00 0.00 0.00 6.07 18.54P25DL004 4.86 0.40 7.17 2.81 0.00 0.00 6.67 21.91P25DL005 8.41 0.68 11.07 4.21 0.00 0.00 11.54 35.91P25DL006 8.18 0.67 12.54 5.07 0.00 0.00 11.23 37.69P25DL008 10.56 0.86 20.66 8.21 0.00 0.00 14.50 54.79P25DL009 15.71 1.28 26.24 10.30 0.00 0.00 21.56 75.09P25DL010 29.27 2.38 30.57 12.56 0.00 0.00 40.18 114.96P25DL011 44.04 3.59 38.15 15.28 0.00 0.00 60.45 161.51P25IC001 9.52 0.78 0.00 2.20 0.00 0.00 13.07 25.57P25IC002 10.60 0.86 0.00 3.45 0.00 0.00 14.55 29.46P25IC003 15.26 1.24 0.00 4.40 0.00 0.00 20.94 41.84P25IC004 16.95 1.38 0.00 5.30 0.00 0.00 23.27 46.90P25IC005 21.09 1.72 0.00 6.25 0.00 0.00 28.95 58.01P25IC006 26.06 2.12 0.00 7.20 0.00 0.00 35.76 71.14P25MK001 8.14 0.66 0.00 2.50 0.00 0.00 11.17 22.47P25MK003 12.62 1.03 0.00 4.15 0.00 0.00 17.33 35.13P25VU002 10.55 0.79 0.00 2.50 0.00 0.00 13.63 27.47P25VU003 12.97 0.97 0.00 2.50 0.00 0.00 16.76 33.20P25VU004 13.26 0.99 0.00 2.50 0.00 0.00 17.13 33.88P25VU005 17.83 1.33 0.00 2.50 0.00 0.00 23.03 44.69P25VU010 18.33 1.36 0.00 0.95 0.00 0.00 23.68 44.32

2 235

EP 1110-1-8, Vol. 430 Nov 11

2-293


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)11/30/2011

4REGION

P25 cont.P25VU011 18.57 1.38 0.00 1.17 0.00 0.00 23.98 45.10

P30P30MK001 13.59 1.11 19.50 2.75 0.00 0.00 18.65 55.60P30MK003 23.08 1.88 34.26 4.83 0.00 0.00 31.68 95.73P30MK004 39.38 3.21 66.40 9.36 0.00 0.00 54.06 172.41

P35P35CA001 13.17 2.33 6.36 1.12 0.00 0.00 17.05 40.03 16.03 2.36 8.23 1.46 0.00 0.00 24.05 52.13P35CA006 40.78 7.20 24.28 4.29 0.00 0.00 52.81 129.36 49.65 7.30 31.42 5.56 0.00 0.00 74.47 168.40P35CA008 24.40 4.31 13.29 2.35 0.00 0.00 31.60 75.95 29.70 4.36 17.20 3.04 0.00 0.00 44.55 98.85P35CA009 31.43 5.55 17.63 3.12 0.00 0.00 40.71 98.44 38.27 5.62 22.81 4.03 0.00 0.00 57.40 128.13

P40P40BX001 1.51 0.13 0.00 0.05 0.00 0.00 1.46 3.15P40TE003 9.92 0.90 2.61 0.32 1.54 0.24 9.61 25.14P40TE004 11.55 1.03 3.59 0.44 1.16 0.18 11.18 29.13P40TE005 8.70 0.79 5.39 0.67 1.54 0.24 8.43 25.76P40TE006 11.76 1.06 5.39 0.67 1.55 0.24 11.39 32.06P40TE007 19.88 1.77 5.39 0.67 1.55 0.24 19.23 48.73P40TE008 22.16 1.97 6.20 0.77 1.55 0.24 21.43 54.32P40TE009 24.76 2.20 6.20 0.77 1.55 0.24 23.94 59.66P40TE010 8.42 0.75 17.14 2.12 0.66 0.10 8.15 37.34P40TE011 9.19 0.83 17.14 2.12 1.08 0.17 8.90 39.43P40TE012 13.90 1.24 17.14 2.12 1.08 0.17 13.45 49.10P40TE013 12.70 1.14 17.14 2.12 1.08 0.17 12.29 46.64P40TE014 12.95 1.16 17.14 2.12 1.08 0.17 12.53 47.15P40TE015 14.73 1.32 17.14 2.12 1.08 0.17 14.25 50.81

2 236

EP 1110-1-8, Vol. 430 Nov 11

2-294


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

P45P45AF002 0.10 0.01 0.00 0.00 0.00 0.00 0.13 0.24P45AF003 0.14 0.01 0.00 0.00 0.00 0.00 0.19 0.34P45AF006 1.12 0.11 3.73 0.53 0.17 0.03 1.46 7.15P45AF007 1.46 0.15 7.76 1.09 0.12 0.02 1.90 12.50P45AF008 0.87 0.08 0.00 0.10 0.00 0.00 1.12 2.17P45AF009 1.94 0.19 1.53 0.29 0.00 0.00 2.50 6.45P45AF010 6.48 0.63 7.04 0.87 0.08 0.01 8.38 23.49P45AF011 5.83 0.56 9.18 1.13 0.08 0.01 7.55 24.34P45AL015 6.69 0.65 7.04 0.87 0.08 0.01 8.65 23.99P45CG001 0.44 0.04 0.00 0.05 0.00 0.00 0.57 1.10P45CG002 0.72 0.07 0.00 0.10 0.00 0.00 0.94 1.83P45CG003 1.65 0.16 0.00 0.15 0.00 0.00 2.14 4.10P45CG006 3.03 0.29 4.97 0.70 0.08 0.01 3.93 13.01P45CG007 2.47 0.24 4.97 0.70 0.00 0.00 3.19 11.57P45OE002 3.84 0.37 8.42 1.04 0.07 0.01 4.97 18.72P45OE003 4.99 0.48 12.85 1.59 0.07 0.01 6.46 26.45P45OE004 5.98 0.58 18.36 2.27 0.07 0.01 7.73 35.00P45OE005 8.03 0.78 27.69 3.42 0.14 0.02 10.39 50.47

P50P50GR001 0.03 0.00 0.00 0.00 0.00 0.00 0.05 0.08P50GR002 0.04 0.00 0.00 0.00 0.00 0.00 0.08 0.12P50GR003 0.07 0.00 0.00 0.00 0.00 0.00 0.13 0.20P50GR004 0.15 0.01 0.00 0.00 0.00 0.00 0.28 0.44P50GR005 0.02 0.00 0.00 0.00 0.00 0.00 0.04 0.06P50GR006 0.04 0.00 0.00 0.00 0.00 0.00 0.07 0.11P50GR007 0.06 0.00 0.00 0.00 0.00 0.00 0.11 0.17

2 237

EP 1110-1-8, Vol. 430 Nov 11

2-295


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)11/30/2011

4REGION

P50 cont.P50GR008 0.11 0.01 0.00 0.00 0.00 0.00 0.21 0.33P50WC001 0.14 0.02 2.92 0.41 0.00 0.00 0.18 3.67P50WC002 0.17 0.02 2.19 0.37 0.00 0.00 0.21 2.96P50WC003 0.39 0.04 2.34 0.39 0.00 0.00 0.49 3.65P50WC004 1.80 0.19 4.82 0.81 0.04 0.01 2.23 9.90P50XX001 2.54 0.27 8.77 1.47 0.00 0.00 3.14 16.19P50XX002 4.69 0.49 10.23 1.72 0.00 0.00 5.79 22.92P50XX003 5.03 0.53 12.43 2.08 0.00 0.00 6.21 26.28

P55P55GF001 2.10 0.22 3.07 0.51 0.00 0.00 2.88 8.78P55GF002 3.01 0.32 10.53 1.77 0.00 0.00 4.13 19.76P55GR001 0.44 0.04 0.15 0.07 0.00 0.00 0.34 1.04P55GR002 0.53 0.05 0.36 0.18 0.00 0.00 0.41 1.53P55GR003 1.44 0.14 1.82 0.90 0.00 0.00 1.12 5.42P55GR004 2.10 0.20 4.37 2.17 0.00 0.00 1.63 10.47P55WC001 0.04 0.00 0.07 0.03 0.00 0.00 0.03 0.17P55WC002 0.06 0.01 0.07 0.03 0.00 0.00 0.05 0.22

P60P60GF003 2.42 0.26 3.07 0.51 0.08 0.01 3.00 9.35P60GF004 2.92 0.31 10.53 1.77 0.08 0.01 3.62 19.24P60GF005 3.87 0.41 16.52 2.77 0.08 0.01 4.79 28.45P60GF006 4.67 0.50 20.47 3.43 0.10 0.02 5.78 34.97P60GF008 3.33 0.35 10.53 1.77 0.08 0.01 4.12 20.19P60GR001 2.51 0.27 6.87 1.15 0.07 0.01 3.11 13.99P60GR002 2.94 0.31 29.53 4.16 0.07 0.01 3.64 40.66P60HO002 0.10 0.01 1.02 0.14 0.00 0.00 0.12 1.39

2 238

EP 1110-1-8, Vol. 430 Nov 11

2-296


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

P60 cont.P60HO003 0.17 0.02 2.34 0.33 0.00 0.00 0.21 3.07P60WC001 0.07 0.01 1.17 0.17 0.00 0.00 0.09 1.51P60WC002 0.09 0.01 1.75 0.25 0.00 0.00 0.12 2.22

P65P65GR001 0.38 0.05 1.46 0.21 0.16 0.02 0.43 2.71P65GR002 0.46 0.06 0.44 0.06 0.16 0.02 0.52 1.72P65GR003 1.20 0.13 0.88 0.12 0.17 0.03 1.34 3.87P65HO001 0.17 0.02 1.02 0.14 0.00 0.00 0.22 1.57P65HO002 0.20 0.02 1.02 0.14 0.00 0.00 0.25 1.63P65WC001 0.19 0.02 1.17 0.17 0.00 0.00 0.20 1.75P65WC002 0.20 0.02 1.17 0.17 0.00 0.00 0.22 1.78

P70P70XX001 0.33 0.04 0.58 0.08 0.00 0.00 0.39 1.42P70XX002 0.87 0.10 1.75 0.25 0.00 0.00 1.02 3.99

R10R10CA001 1.10 0.12 0.00 0.08 0.00 0.00 1.35 2.65 1.35 0.12 0.00 0.08 0.00 0.00 1.84 3.39R10CA003 1.10 0.12 0.00 0.08 0.00 0.00 1.35 2.65 1.35 0.12 0.00 0.08 0.00 0.00 1.84 3.39R10CA005 1.10 0.12 0.00 0.08 0.00 0.00 1.35 2.65 1.35 0.12 0.00 0.08 0.00 0.00 1.84 3.39R10CA006 0.03 0.00 0.00 0.00 0.00 0.00 0.04 0.07 0.04 0.00 0.00 0.00 0.00 0.00 0.05 0.09R10CA007 2.52 0.27 0.00 0.08 0.00 0.00 3.09 5.96 3.10 0.27 0.00 0.08 0.00 0.00 4.23 7.68R10CA009 4.69 0.49 0.00 0.08 0.00 0.00 5.76 11.02 5.78 0.51 0.00 0.08 0.00 0.00 7.88 14.25R10CA010 0.19 0.02 0.00 0.00 0.00 0.00 0.23 0.44 0.23 0.02 0.00 0.00 0.00 0.00 0.32 0.57R10CA011 5.10 0.54 0.00 0.10 0.00 0.00 6.26 12.00 6.28 0.55 0.00 0.10 0.00 0.00 8.56 15.49R10CA012 6.02 0.63 0.00 0.10 0.00 0.00 7.39 14.14 7.41 0.65 0.00 0.10 0.00 0.00 10.10 18.26R10CA013 0.42 0.04 0.00 0.00 0.00 0.00 0.52 0.98 0.52 0.05 0.00 0.00 0.00 0.00 0.70 1.27

2 239

EP 1110-1-8, Vol. 430 Nov 11

2-297


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)11/30/2011

4REGION

R10 cont.R10CA014 6.56 0.69 0.00 0.16 0.00 0.00 8.05 15.46 8.07 0.71 0.00 0.16 0.00 0.00 11.01 19.95R10CA015 7.47 0.79 0.00 0.16 0.00 0.00 9.17 17.59 9.20 0.80 0.00 0.16 0.00 0.00 12.54 22.70R10CA016 0.42 0.04 0.00 0.00 0.00 0.00 0.52 0.98 0.52 0.05 0.00 0.00 0.00 0.00 0.71 1.28R10CA017 9.99 1.05 0.00 0.21 0.00 0.00 12.27 23.52 12.30 1.08 0.00 0.21 0.00 0.00 16.77 30.36R10CA018 11.93 1.25 0.00 0.22 0.00 0.00 14.64 28.04 14.68 1.28 0.00 0.22 0.00 0.00 20.02 36.20R10CA019 0.69 0.07 0.00 0.24 0.00 0.00 0.84 1.84 0.84 0.07 0.00 0.24 0.00 0.00 1.15 2.30R10CA020 12.09 1.27 0.00 0.23 0.00 0.00 14.84 28.43 14.88 1.30 0.00 0.23 0.00 0.00 20.29 36.70R10CA021 12.48 1.31 0.00 0.25 0.00 0.00 15.32 29.36 15.36 1.34 0.00 0.25 0.00 0.00 20.95 37.90R10CA022 0.12 0.01 0.00 0.00 0.00 0.00 0.14 0.27 0.14 0.01 0.00 0.00 0.00 0.00 0.19 0.34R10CA023 0.12 0.01 0.00 0.00 0.00 0.00 0.14 0.27 0.14 0.01 0.00 0.00 0.00 0.00 0.20 0.35

R15R15SO001 10.44 1.51 0.00 0.40 1.68 0.26 10.26 24.55R15SO002 9.94 1.67 0.00 0.45 3.89 0.61 10.11 26.67R15SO003 15.06 2.33 0.00 0.67 3.89 0.61 15.01 37.57

R20R20RI002 2.93 0.38 0.00 0.25 0.00 0.00 3.21 6.77R20SO001 6.50 0.84 0.00 0.25 0.00 0.00 7.13 14.72

R30R30BO003 14.29 1.46 14.21 1.50 2.15 0.34 13.02 46.97R30BO004 7.30 0.77 10.98 1.16 1.84 0.29 6.69 29.03R30BO005 7.02 0.82 6.07 0.64 0.00 0.00 7.24 21.79R30BO006 7.66 0.90 10.72 1.13 0.00 0.00 7.90 28.31R30BO007 8.94 1.05 10.08 1.07 0.00 0.00 9.22 30.36R30BO008 36.24 5.54 57.11 6.03 0.00 0.00 39.73 144.65R30BO009 35.48 5.42 57.11 6.03 0.00 0.00 38.90 142.94

2 240

EP 1110-1-8, Vol. 430 Nov 11

2-298


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

R30 cont.R30CA003 26.51 4.05 31.01 3.28 0.00 0.00 29.07 93.92R30CA006 40.18 6.14 40.70 4.30 0.00 0.00 44.05 135.37R30CA009 55.28 8.45 61.11 6.46 0.00 0.00 60.60 191.90R30CA010 8.56 0.84 9.04 0.96 0.49 0.08 7.75 27.72R30CA011 10.80 1.06 13.57 1.43 0.72 0.11 9.78 37.47R30CA012 27.03 4.13 28.42 3.00 0.00 0.00 29.63 92.21R30CA013 41.82 6.39 40.70 4.30 0.00 0.00 45.84 139.05R30CA014 14.94 1.53 13.57 1.43 4.65 0.73 13.62 50.47R30RS001 1.36 0.16 4.16 0.44 0.00 0.00 1.40 7.52R30RS002 2.71 0.32 5.17 0.55 0.00 0.00 2.80 11.55R30RS003 7.21 0.72 10.34 1.09 0.75 0.12 6.55 26.78R30SI002 11.98 1.21 11.76 1.24 1.45 0.23 10.89 38.76R30SI003 15.01 1.50 12.27 1.30 1.45 0.23 13.63 45.39R30SI004 20.17 1.99 13.95 1.47 1.29 0.20 18.28 57.35R30SI005 10.78 1.27 9.69 1.02 0.00 0.00 11.12 33.88

R40R40BO001 6.64 0.70 7.31 1.03 0.00 0.00 7.28 22.96R40BO002 7.20 0.76 7.31 1.03 0.00 0.00 7.89 24.19

R45R45BO004 3.97 0.42 4.82 0.68 0.00 0.00 5.99 15.88R45BO005 5.84 0.61 6.73 0.95 0.00 0.00 8.81 22.94R45BO006 11.76 1.24 15.79 2.23 0.00 0.00 17.73 48.75R45BO007 13.46 1.42 19.15 2.70 0.00 0.00 20.29 57.02R45BO008 15.06 1.59 29.97 4.23 0.00 0.00 22.71 73.56R45CA001 5.11 0.54 4.68 0.66 0.00 0.00 7.71 18.70R45CA002 5.86 0.62 4.68 0.66 0.00 0.00 8.83 20.65

2 241

EP 1110-1-8, Vol. 430 Nov 11

2-299


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)11/30/2011

4REGION

R45 cont.R45CA005 12.03 1.27 10.23 1.44 0.00 0.00 18.13 43.10R45CA007 17.28 1.82 15.35 2.16 0.00 0.00 26.05 62.66R45CA010 21.50 2.26 21.20 2.99 0.00 0.00 32.41 80.36R45RS001 2.05 0.22 2.92 0.41 0.00 0.00 3.09 8.69R45SI008 3.95 0.42 5.12 0.72 0.00 0.00 5.96 16.17R45SI009 10.76 1.13 11.40 1.61 0.00 0.00 16.22 41.12R45SI010 14.43 1.52 18.57 2.62 0.00 0.00 21.75 58.89

R50R50BO005 4.70 0.62 5.27 0.74 1.82 0.28 7.11 20.54R50BO006 7.80 0.91 7.91 1.12 0.22 0.03 11.42 29.41R50BO007 8.98 1.06 7.91 1.12 0.54 0.08 13.20 32.89R50BO008 15.09 1.82 16.34 2.30 1.82 0.28 22.29 59.94R50BO009 13.93 1.69 20.55 2.90 1.82 0.28 20.59 61.76R50BO010 5.35 0.64 5.27 0.74 0.47 0.07 7.89 20.43R50BO011 8.23 0.96 7.91 1.12 0.22 0.03 12.05 30.52R50BO012 10.60 1.25 10.65 1.50 0.54 0.08 15.55 40.17R50BO013 15.88 1.91 13.81 1.95 1.82 0.28 23.44 59.09R50CA001 8.17 0.96 7.38 1.04 0.35 0.05 11.99 29.94R50CA002 9.06 1.06 7.38 1.04 0.35 0.05 13.29 32.23R50CA003 11.65 1.37 10.22 1.44 0.61 0.10 17.11 42.50R50CA004 12.86 1.51 10.54 1.49 0.61 0.10 18.87 45.98R50CA005 11.46 1.35 10.54 1.49 0.61 0.10 16.83 42.38R50CA009 15.73 1.89 15.81 2.23 1.63 0.25 23.20 60.74R50CA010 18.94 2.26 15.81 2.23 1.63 0.25 27.89 69.01R50CA011 19.47 2.32 15.81 2.23 1.63 0.25 28.66 70.37R50CA012 18.96 2.26 15.81 2.23 1.63 0.25 27.92 69.06R50IP001 8.94 1.06 8.43 1.19 0.73 0.11 13.15 33.61

2 242

EP 1110-1-8, Vol. 430 Nov 11

2-300


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

R50 cont.R50SI006 7.41 0.89 6.32 0.89 0.69 0.11 10.91 27.22R50SI007 7.95 0.95 6.32 0.89 0.69 0.11 11.70 28.61R50SI013 11.96 1.46 15.60 2.20 1.82 0.28 17.71 51.03R50SI016 12.84 1.56 15.60 2.20 1.82 0.28 19.00 53.30R50SI017 13.95 1.69 15.60 2.20 1.82 0.28 20.63 56.17R50SI022 10.21 1.21 10.54 1.49 0.64 0.10 15.01 39.20R50SI023 11.47 1.35 10.54 1.49 0.64 0.10 16.85 42.44R50SI024 5.69 0.68 2.95 0.42 0.41 0.06 8.37 18.58R50SI025 7.06 0.83 3.16 0.45 0.41 0.06 10.37 22.34R50SI026 14.19 1.66 10.96 1.55 0.41 0.06 20.79 49.62

R55R55GL001 0.67 0.05 0.00 0.50 0.03 0.00 0.70 1.95R55GL002 0.91 0.07 0.97 0.60 0.06 0.01 0.94 3.56R55GL003 2.53 0.19 1.75 0.93 0.04 0.01 2.62 8.07R55GL004 3.09 0.23 1.75 1.18 0.04 0.01 3.20 9.50R55GL007 1.97 0.15 3.51 0.37 0.00 0.00 2.03 8.03R55GL009 0.45 0.03 2.05 0.22 0.00 0.00 0.46 3.21R55GL011 1.12 0.08 3.12 0.33 0.00 0.00 1.16 5.81R55GL012 1.76 0.14 1.75 0.93 0.06 0.01 1.83 6.48R55GL013 0.15 0.02 0.00 0.25 0.12 0.02 0.18 0.74R55GL014 0.59 0.04 0.00 0.35 0.00 0.00 0.61 1.59R55GL015 1.85 0.14 1.75 0.18 0.00 0.00 1.91 5.83R55GL016 0.79 0.06 1.75 0.18 0.00 0.00 0.81 3.59R55GL017 0.34 0.03 0.97 0.10 0.00 0.00 0.36 1.80R55GL018 0.39 0.03 0.97 0.10 0.00 0.00 0.40 1.89R55GL019 0.76 0.06 1.56 0.16 0.00 0.00 0.79 3.33R55GL020 0.62 0.05 0.97 0.10 0.11 0.02 0.66 2.53

2 243

EP 1110-1-8, Vol. 430 Nov 11

2-301


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)11/30/2011

4REGION

R55 cont.R55GL021 0.42 0.03 1.75 0.18 0.00 0.00 0.43 2.81R55GL022 3.89 0.30 1.56 7.16 0.20 0.03 4.05 17.19R55GL023 1.17 0.09 1.56 0.16 0.06 0.01 1.21 4.26

S10S10CA001 23.58 3.13 18.45 3.25 3.01 0.47 30.01 81.90 29.48 3.19 24.40 4.30 12.17 1.90 41.66 117.10S10CA002 23.92 4.74 27.93 3.94 13.59 2.12 34.81 111.05 27.04 4.77 36.94 5.21 54.89 8.56 41.42 178.83S10CA003 26.59 5.15 38.47 5.43 11.11 1.73 38.49 126.97 30.06 5.19 50.88 7.18 44.90 7.00 45.79 191.00

S15S15CA001 29.43 5.84 35.99 5.08 11.11 1.73 33.41 122.59 35.32 5.89 45.92 6.48 44.90 7.00 42.64 188.15S15CA002 42.98 8.50 44.37 6.26 15.42 2.41 48.76 168.70 51.57 8.58 56.61 7.98 62.32 9.72 62.23 259.01S15CA003 55.37 11.08 54.23 7.65 24.51 3.82 62.97 219.63 66.45 11.18 69.19 9.76 99.05 15.45 80.36 351.44S15JU001 30.57 5.93 41.61 5.87 4.14 0.65 34.54 123.31 36.68 5.99 53.09 7.49 15.39 2.40 44.08 165.12S15JU002 31.66 6.14 41.61 5.87 4.14 0.65 35.78 125.85 38.00 6.20 53.09 7.49 15.39 2.40 45.65 168.22

S20S20CA001 24.44 4.90 56.61 6.50 13.96 2.18 29.56 138.15 27.15 4.92 73.60 8.45 59.08 9.22 34.77 217.19S20CA002 35.64 7.01 56.61 6.50 13.96 2.18 42.95 164.85 39.60 7.04 73.60 8.45 59.08 9.22 50.52 247.51S20CA003 55.58 10.88 71.40 8.20 19.38 3.02 66.92 235.38 61.75 10.93 92.82 10.66 82.00 12.79 78.71 349.66S20CA004 57.97 11.33 71.40 8.20 19.38 3.02 69.78 241.08 64.41 11.39 92.82 10.66 82.00 12.79 82.07 356.14S20CA005 70.42 13.94 96.90 11.12 32.21 5.02 84.98 314.59 78.25 14.01 125.97 14.46 136.27 21.26 99.96 490.18S20CA006 75.08 14.79 96.90 11.12 30.81 4.81 90.51 324.02 83.42 14.86 125.97 14.46 130.33 20.33 106.46 495.83

S25S25JD001 3.37 0.57 0.00 1.50 1.35 0.21 3.39 10.39 4.05 0.58 0.00 1.50 5.03 0.78 4.35 16.29S25JD002 4.14 0.71 0.00 1.50 2.03 0.32 4.17 12.87 4.96 0.72 0.00 1.50 7.55 1.18 5.36 21.27S25RI001 2.96 0.47 0.00 1.50 0.43 0.07 2.94 8.37 3.55 0.48 0.00 1.50 1.61 0.25 3.77 11.16

2 244

EP 1110-1-8, Vol. 430 Nov 11

2-302


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

S25 cont.S25RI002 3.30 0.53 0.00 1.50 0.65 0.10 3.27 9.35 3.95 0.54 0.00 1.50 2.41 0.38 4.21 12.99S25RM001 7.76 1.33 0.00 1.50 4.29 0.67 7.81 23.36 9.31 1.34 0.00 1.50 15.79 2.46 10.04 40.44S25RM002 11.26 1.96 0.00 1.50 7.05 1.10 11.39 34.26 13.51 1.98 0.00 1.50 26.08 4.07 14.63 61.77S25RM003 5.63 1.00 0.00 1.50 4.29 0.67 5.72 18.81 6.75 1.01 0.00 1.50 15.79 2.46 7.35 34.86

S30S30HW001 12.09 3.13 13.16 6.53 1.26 0.20 14.78 51.15 20.14 3.21 15.80 9.48 1.42 0.22 30.81 81.08S30HW002 16.33 4.22 18.43 9.14 1.56 0.24 19.97 69.89 27.22 4.33 22.11 13.27 1.76 0.27 41.62 110.58S30HW005 6.55 1.70 2.11 1.05 0.76 0.12 5.21 17.50 10.91 1.75 2.53 1.52 0.84 0.13 11.36 29.04S30HW006 11.01 2.83 5.27 2.61 0.81 0.13 8.75 31.41 18.35 2.91 6.32 3.79 0.91 0.14 19.08 51.50S30HW007 11.98 3.08 6.58 3.26 0.81 0.13 9.52 35.36 19.97 3.16 7.90 4.74 0.91 0.14 20.76 57.58S30HW008 12.53 3.22 6.58 3.26 0.81 0.13 9.95 36.48 20.88 3.30 7.90 4.74 0.91 0.14 21.70 59.57S30HW009 12.90 3.33 7.90 3.92 1.19 0.19 10.26 39.69 21.51 3.42 9.48 5.69 1.35 0.21 22.37 64.03S30HW010 15.76 4.06 10.53 5.22 1.33 0.21 12.53 49.64 26.26 4.17 12.64 7.59 1.50 0.23 27.31 79.70S30HW011 15.43 3.98 10.53 5.22 1.40 0.22 12.27 49.05 25.71 4.09 12.64 7.59 1.57 0.24 26.74 78.58S30HW012 18.26 4.71 10.53 5.22 1.56 0.24 14.51 55.03 30.43 4.83 12.64 7.59 1.76 0.27 31.64 89.16S30HW013 14.69 3.79 23.69 11.75 1.23 0.19 17.96 73.30 24.49 3.89 28.43 17.06 1.38 0.22 37.44 112.91S30HW014 11.93 1.31 0.79 0.39 0.49 0.08 11.68 26.67 14.92 1.34 0.95 0.57 0.56 0.09 18.24 36.67S30HW015 13.14 1.44 1.32 0.65 0.49 0.08 12.86 29.98 16.43 1.47 1.58 0.95 0.56 0.09 20.09 41.17S30HW016 12.42 1.36 1.05 0.52 0.49 0.08 12.16 28.08 15.53 1.39 1.26 0.76 0.56 0.09 18.99 38.58S30HW017 13.38 1.46 1.32 0.65 0.49 0.08 13.10 30.48 16.73 1.50 1.58 0.95 0.56 0.09 20.45 41.86S30HW018 15.74 1.74 2.11 1.05 0.92 0.14 15.42 37.12 19.67 1.78 2.53 1.52 1.02 0.16 24.08 50.76S30KB001 3.17 0.37 0.53 0.26 0.44 0.07 2.73 7.57 3.97 0.38 0.63 0.38 0.49 0.08 4.15 10.08S30KB002 4.11 0.48 0.79 0.39 0.55 0.09 3.54 9.95 5.13 0.49 0.95 0.57 0.62 0.10 5.37 13.23S30KB003 3.46 0.39 1.05 0.52 0.31 0.05 2.97 8.75 4.33 0.40 1.26 0.76 0.34 0.05 4.51 11.65S30KB004 5.00 0.60 1.32 0.65 0.93 0.15 4.32 12.97 6.24 0.61 1.58 0.95 1.04 0.16 6.55 17.13S30KB005 3.89 0.46 1.32 0.65 0.63 0.10 3.35 10.40 4.86 0.47 1.58 0.95 0.71 0.11 5.09 13.77S30KB006 5.71 0.68 1.58 0.78 0.99 0.15 4.93 14.82 7.14 0.69 1.90 1.14 1.10 0.17 7.49 19.63

2 245

EP 1110-1-8, Vol. 430 Nov 11

2-303


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)11/30/2011

4REGION

S30 cont.S30KB007 3.69 0.42 0.53 0.26 0.44 0.07 3.17 8.58 4.61 0.43 0.63 0.38 0.49 0.08 4.82 11.44S30KB008 4.57 0.52 0.79 0.39 0.48 0.07 3.93 10.75 5.71 0.53 0.95 0.57 0.54 0.08 5.96 14.34S30KB009 6.16 0.72 0.79 0.39 0.94 0.15 5.31 14.46 7.70 0.74 0.95 0.57 1.05 0.16 8.07 19.24S30KB010 3.80 0.44 1.05 0.52 0.58 0.09 3.28 9.76 4.75 0.45 1.26 0.76 0.66 0.10 4.97 12.95S30KB011 5.54 0.63 1.32 0.65 0.64 0.10 4.77 13.65 6.93 0.65 1.58 0.95 0.72 0.11 7.24 18.18S30KB012 6.55 0.77 1.32 0.65 1.02 0.16 5.65 16.12 8.19 0.78 1.58 0.95 1.14 0.18 8.58 21.40S30KB013 4.43 0.51 1.32 0.65 0.63 0.10 3.82 11.46 5.53 0.53 1.58 0.95 0.71 0.11 5.79 15.20S30KB014 6.00 0.69 1.58 0.78 0.70 0.11 5.16 15.02 7.50 0.70 1.90 1.14 0.79 0.12 7.84 19.99S30KB015 8.03 0.93 2.11 1.05 1.09 0.17 6.92 20.30 10.04 0.95 2.53 1.52 1.22 0.19 10.51 26.96S30KB018 9.53 1.06 1.32 0.65 0.67 0.10 8.18 21.51 11.92 1.09 1.58 0.95 0.75 0.12 12.42 28.83S30KB021 11.06 1.23 2.11 1.05 0.76 0.12 9.49 25.82 13.83 1.26 2.53 1.52 0.85 0.13 14.41 34.53S30KB024 12.70 1.41 3.16 1.57 0.84 0.13 10.89 30.70 15.87 1.45 3.79 2.27 0.95 0.15 16.53 41.01S30KB025 6.74 0.76 1.05 0.52 0.55 0.09 5.79 15.50 8.43 0.77 1.26 0.76 0.62 0.10 8.79 20.73S30KB026 8.05 0.90 1.05 0.52 0.60 0.09 6.91 18.12 10.06 0.92 1.26 0.76 0.67 0.10 10.49 24.26S30KB027 10.23 1.14 1.32 0.65 0.67 0.10 8.77 22.88 12.78 1.16 1.58 0.95 0.75 0.12 13.32 30.66S30KB028 7.68 0.86 1.58 0.78 0.61 0.10 6.59 18.20 9.60 0.88 1.90 1.14 0.69 0.11 10.01 24.33S30KB029 9.28 1.04 1.58 0.78 0.67 0.10 7.97 21.42 11.61 1.06 1.90 1.14 0.75 0.12 12.10 28.68S30KB030 11.71 1.30 2.11 1.05 0.76 0.12 10.04 27.09 14.63 1.33 2.53 1.52 0.85 0.13 15.25 36.24S30KB031 10.05 1.12 2.63 1.30 0.67 0.10 8.62 24.49 12.56 1.14 3.16 1.90 0.75 0.12 13.09 32.72S30KB032 11.86 1.32 2.63 1.30 0.76 0.12 10.17 28.16 14.83 1.35 3.16 1.90 0.86 0.13 15.45 37.68S30KB033 13.70 1.52 3.16 1.57 0.84 0.13 11.75 32.67 17.12 1.55 3.79 2.27 0.95 0.15 17.84 43.67S30KB034 4.85 0.56 0.79 0.39 0.61 0.10 4.18 11.48 6.07 0.57 0.95 0.57 0.69 0.11 6.35 15.31S30KB035 5.52 0.64 1.05 0.52 0.73 0.11 4.75 13.32 6.90 0.65 1.26 0.76 0.82 0.13 7.22 17.74S30KB036 5.20 0.60 1.05 0.52 0.67 0.10 4.48 12.62 6.50 0.61 1.26 0.76 0.75 0.12 6.79 16.79S30KB041 5.93 0.69 1.05 0.52 0.81 0.13 5.10 14.23 7.41 0.70 1.26 0.76 0.91 0.14 7.75 18.93S30KB042 8.52 0.95 1.58 0.78 0.55 0.09 7.30 19.77 10.64 0.97 1.90 1.14 0.62 0.10 11.09 26.46S30KB043 12.72 1.40 0.79 0.39 0.60 0.09 10.90 26.89 15.90 1.43 0.95 0.57 0.67 0.10 16.55 36.17

2 246

EP 1110-1-8, Vol. 430 Nov 11

2-304


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

S30 cont.S30KB044 15.70 1.72 0.79 0.39 0.60 0.09 13.45 32.74 19.62 1.76 0.95 0.57 0.67 0.10 20.41 44.08S30KB045 21.19 5.42 37.94 4.69 0.95 0.15 25.88 96.22 35.32 5.56 45.29 6.71 1.07 0.17 53.95 148.07S30KB046 14.56 3.75 14.32 7.10 1.16 0.18 21.37 62.44 24.27 3.85 17.18 10.31 1.31 0.20 47.48 104.60S30KB047 18.44 4.71 16.58 8.23 0.88 0.14 27.04 76.02 30.74 4.84 19.90 11.94 0.99 0.15 60.08 128.64S30KB048 16.09 1.77 4.48 2.22 0.69 0.11 15.76 41.12 20.11 1.81 5.37 3.22 0.78 0.12 24.60 56.01S30KB049 18.05 2.08 4.74 2.35 2.48 0.39 17.76 47.85 22.56 2.13 5.69 3.41 2.79 0.44 27.74 64.76S30KB050 23.09 2.51 13.16 6.53 0.64 0.10 22.59 68.62 28.86 2.57 15.80 9.48 0.71 0.11 35.27 92.80S30KB051 29.24 3.19 13.16 6.53 0.95 0.15 28.62 81.84 36.55 3.27 15.80 9.48 1.07 0.17 44.69 111.03S30KB052 30.96 3.34 13.16 6.53 0.32 0.05 30.25 84.61 38.69 3.41 15.80 9.48 0.36 0.06 47.24 115.04S30KB053 8.78 0.98 2.11 1.05 0.60 0.09 7.53 21.14 10.98 1.00 2.53 1.52 0.67 0.10 11.44 28.24S30KB054 8.72 0.97 0.79 0.39 0.55 0.09 7.48 18.99 10.90 0.99 0.95 0.57 0.62 0.10 11.36 25.49S30KB055 13.73 3.52 25.82 3.19 0.81 0.13 10.91 58.11 22.88 3.61 30.82 4.56 0.91 0.14 23.78 86.70S30KB056 14.07 3.61 25.82 3.19 0.81 0.13 11.18 58.81 23.46 3.70 30.82 4.56 0.91 0.14 24.38 87.97S30KB057 15.72 4.02 25.82 3.19 0.81 0.13 12.49 62.18 26.20 4.13 30.82 4.56 0.91 0.14 27.22 93.98S30KB058 14.72 3.77 6.84 3.39 0.79 0.12 11.69 41.32 24.53 3.86 8.21 4.93 0.89 0.14 25.49 68.05S30KB059 23.11 5.91 15.80 7.84 1.11 0.17 18.35 72.29 38.52 6.06 18.95 11.37 1.24 0.19 40.02 116.35S30PU002 53.02 5.73 42.16 5.21 1.07 0.17 45.35 152.71 66.28 5.86 50.32 7.45 1.26 0.20 68.85 200.22S30PU003 66.77 7.21 42.16 5.21 1.16 0.18 57.10 179.79 83.46 7.37 50.32 7.45 1.37 0.21 86.68 236.86S30PU004 78.41 8.45 42.16 5.21 1.16 0.18 67.04 202.61 98.01 8.65 50.32 7.45 1.37 0.21 101.79 267.80S30RA002 6.79 0.74 2.64 0.33 0.17 0.03 6.64 17.34 8.49 0.76 3.15 0.47 0.19 0.03 10.37 23.46S30RA003 10.70 1.17 5.16 0.64 0.34 0.05 10.47 28.53 13.38 1.20 6.16 0.91 0.39 0.06 16.35 38.45S30TS001 3.38 0.39 0.63 0.31 0.37 0.06 2.90 8.04 4.22 0.39 0.76 0.46 0.42 0.07 4.41 10.73S30TS002 4.61 0.52 0.90 0.45 0.47 0.07 3.96 10.98 5.76 0.54 1.07 0.64 0.53 0.08 6.01 14.63S30TS003 3.47 0.40 0.90 0.45 0.43 0.07 2.99 8.71 4.34 0.41 1.07 0.64 0.49 0.08 4.54 11.57S30TS004 4.73 0.54 1.16 0.58 0.55 0.09 4.07 11.72 5.91 0.55 1.39 0.83 0.62 0.10 6.17 15.57S30TS005 3.64 0.42 1.16 0.58 0.49 0.08 3.13 9.50 4.54 0.43 1.39 0.83 0.55 0.09 4.75 12.58S30TS006 4.94 0.57 1.42 0.70 0.63 0.10 4.25 12.61 6.18 0.58 1.71 1.03 0.71 0.11 6.46 16.78

2 247

EP 1110-1-8, Vol. 430 Nov 11

2-305


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)11/30/2011

4REGION

S30 cont.S30TS007 4.37 0.50 1.68 0.83 0.55 0.09 3.76 11.78 5.47 0.51 2.02 1.21 0.62 0.10 5.71 15.64S30TS008 7.48 0.84 2.21 1.10 0.71 0.11 6.42 18.87 9.35 0.86 2.65 1.59 0.80 0.12 9.75 25.12S30TS009 11.41 2.88 15.80 10.84 0.00 0.00 13.92 54.85 19.02 2.96 18.95 14.37 0.00 0.00 29.02 84.32S30TS010 16.74 4.23 21.06 14.45 0.00 0.00 20.43 76.91 27.90 4.34 25.27 19.16 0.00 0.00 42.57 119.24S30TS011 27.73 7.00 42.12 28.89 0.00 0.00 33.83 139.57 46.21 7.19 50.54 38.33 0.00 0.00 70.50 212.77

S35S35AR001 0.52 0.05 0.00 0.00 0.00 0.00 0.57 1.14S35AR002 0.73 0.08 0.00 0.00 0.00 0.00 0.80 1.61

S40S40BO002 26.84 3.55 41.62 5.14 2.13 0.33 32.24 111.85 33.56 3.62 53.86 6.65 8.80 1.37 45.02 152.88S40BO003 25.29 3.35 41.62 5.14 2.13 0.33 30.38 108.24 31.62 3.42 53.86 6.65 8.80 1.37 42.43 148.15S40BO004 25.74 3.41 41.62 5.14 2.13 0.33 30.92 109.29 32.18 3.47 53.86 6.65 8.80 1.37 43.18 149.51S40CA001 30.07 3.94 35.72 4.41 2.04 0.32 36.05 112.55 37.58 4.02 46.23 5.71 7.93 1.24 50.34 153.05S40CA002 28.49 3.78 35.72 4.41 2.06 0.32 34.24 109.02 35.61 3.86 46.23 5.71 7.82 1.22 47.82 148.27S40CA003 23.13 3.29 40.46 5.00 11.97 1.87 28.21 113.93 28.92 3.36 52.36 6.47 47.61 7.43 39.40 185.55S40CA004 38.00 5.15 62.42 7.71 9.00 1.40 45.88 169.56 47.50 5.25 80.78 9.98 34.75 5.42 64.06 247.74

S45S45DA004 1.73 0.14 0.00 0.25 0.00 0.00 2.37 4.49S45DA005 2.06 0.17 0.00 0.25 0.00 0.00 2.83 5.31S45DA007 2.18 0.18 0.00 0.25 0.00 0.00 2.99 5.60

T10T10CA001 1.13 0.15 0.00 0.08 0.00 0.00 1.23 2.59 1.41 0.15 0.00 0.08 0.00 0.00 1.73 3.37T10CA002 1.69 0.22 0.00 0.08 0.00 0.00 1.84 3.83 2.11 0.22 0.00 0.08 0.00 0.00 2.59 5.00T10CA004 1.25 0.16 0.00 0.08 0.00 0.00 1.36 2.85 1.56 0.16 0.00 0.08 0.00 0.00 1.91 3.71

2 248

EP 1110-1-8, Vol. 430 Nov 11

2-306


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

T10 cont.T10CA005 1.69 0.22 0.00 0.08 0.00 0.00 1.84 3.83 2.11 0.22 0.00 0.08 0.00 0.00 2.59 5.00T10CA007 1.89 0.24 0.00 0.08 0.00 0.00 2.06 4.27 2.36 0.25 0.00 0.08 0.00 0.00 2.89 5.58T10CA008 2.52 0.32 0.00 0.08 0.00 0.00 2.75 5.67 3.15 0.33 0.00 0.08 0.00 0.00 3.87 7.43T10CA009 2.30 0.30 0.00 0.08 0.00 0.00 2.51 5.19 2.88 0.30 0.00 0.08 0.00 0.00 3.53 6.79T10CA010 2.52 0.32 0.00 0.08 0.00 0.00 2.75 5.67 3.15 0.33 0.00 0.08 0.00 0.00 3.86 7.42T10CA011 3.51 0.45 0.00 0.08 0.00 0.00 3.83 7.87 4.39 0.46 0.00 0.08 0.00 0.00 5.38 10.31T10CA012 3.39 0.44 0.00 0.08 0.00 0.00 3.70 7.61 4.24 0.45 0.00 0.08 0.00 0.00 5.20 9.97T10CA013 3.72 0.48 0.00 0.08 0.00 0.00 4.06 8.34 4.65 0.49 0.00 0.08 0.00 0.00 5.71 10.93T10CA014 3.10 0.40 0.00 0.08 0.00 0.00 3.38 6.96 3.87 0.41 0.00 0.08 0.00 0.00 4.75 9.11T10CA015 4.61 0.59 0.00 0.10 0.00 0.00 5.03 10.33 5.77 0.61 0.00 0.10 0.00 0.00 7.08 13.56T10CA016 4.51 0.58 0.00 0.12 0.00 0.00 4.93 10.14 5.64 0.59 0.00 0.12 0.00 0.00 6.93 13.28T10CA017 4.90 0.63 0.00 0.13 0.00 0.00 5.35 11.01 6.12 0.64 0.00 0.13 0.00 0.00 7.52 14.41T10CA018 4.33 0.56 0.00 0.13 0.00 0.00 4.73 9.75 5.42 0.57 0.00 0.13 0.00 0.00 6.65 12.77T10CA019 0.12 0.02 0.00 0.05 0.00 0.00 0.14 0.33 0.16 0.02 0.00 0.05 0.00 0.00 0.19 0.42T10CA020 4.60 0.59 0.00 0.15 0.00 0.00 5.02 10.36 5.75 0.60 0.00 0.15 0.00 0.00 7.05 13.55T10CA021 6.13 0.79 0.00 0.19 0.00 0.00 6.69 13.80 7.67 0.81 0.00 0.19 0.00 0.00 9.41 18.08T10CA022 6.65 0.86 0.00 0.19 0.00 0.00 7.26 14.96 8.31 0.87 0.00 0.19 0.00 0.00 10.20 19.57T10CA023 6.18 0.80 0.00 0.20 0.00 0.00 6.75 13.93 7.73 0.81 0.00 0.20 0.00 0.00 9.49 18.23T10CA024 9.15 1.18 0.00 0.28 0.00 0.00 9.98 20.59 11.43 1.20 0.00 0.28 0.00 0.00 14.03 26.94T10CA025 9.73 1.26 0.00 0.29 0.00 0.00 10.62 21.90 12.16 1.28 0.00 0.29 0.00 0.00 14.93 28.66T10CA026 13.28 1.71 0.00 0.40 0.00 0.00 14.49 29.88 16.59 1.75 0.00 0.40 0.00 0.00 20.37 39.11T10CA027 14.32 1.85 0.00 0.42 0.00 0.00 15.63 32.22 17.90 1.88 0.00 0.42 0.00 0.00 21.98 42.18T10JD001 1.06 0.14 0.00 0.25 0.11 0.02 1.17 2.75 1.33 0.15 0.00 0.25 0.12 0.02 1.64 3.51

T15T15CA002 6.86 1.08 8.09 1.29 0.00 0.00 11.75 29.07 8.57 1.10 10.47 1.67 0.00 0.00 16.70 38.51T15CA005 8.47 1.33 9.25 1.47 0.00 0.00 14.52 35.04 10.59 1.35 11.97 1.90 0.00 0.00 20.64 46.45T15CA008 16.91 2.66 16.76 2.67 0.00 0.00 28.98 67.98 21.13 2.70 21.69 3.45 0.00 0.00 41.18 90.15

2 249

EP 1110-1-8, Vol. 430 Nov 11

2-307


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)11/30/2011

4REGION

T15 cont.T15CA009 24.23 3.81 19.07 3.03 0.00 0.00 41.53 91.67 30.28 3.87 24.68 3.93 0.00 0.00 59.01 121.77T15CA011 23.57 3.71 21.39 3.40 0.00 0.00 40.41 92.48 29.47 3.77 27.68 4.40 0.00 0.00 57.42 122.74T15CA012 24.08 4.22 27.74 3.43 0.00 0.00 42.03 101.50 28.67 4.27 35.90 4.44 0.00 0.00 52.14 125.42T15CA014 28.55 5.01 27.74 3.43 0.00 0.00 49.83 114.56 33.99 5.06 35.90 4.44 0.00 0.00 61.82 141.21T15CA016 31.50 5.53 35.84 4.44 0.00 0.00 54.98 132.29 37.50 5.58 46.38 5.74 0.00 0.00 68.21 163.41T15CA017 41.91 7.35 47.40 5.87 0.00 0.00 73.15 175.68 49.90 7.43 61.34 7.59 0.00 0.00 90.75 217.01T15CA018 52.93 9.99 57.19 3.93 0.00 0.00 86.60 210.64 63.51 10.08 72.96 5.01 0.00 0.00 116.94 268.50T15CA019 82.19 15.51 83.81 5.75 0.00 0.00 134.49 321.75 98.63 15.66 106.93 7.34 0.00 0.00 181.61 410.17T15CA020 8.65 1.36 9.25 1.47 0.00 0.00 14.82 35.55 10.81 1.38 11.97 1.90 0.00 0.00 21.06 47.12T15CA021 8.95 1.41 10.40 1.65 0.00 0.00 15.34 37.75 11.19 1.43 13.46 2.14 0.00 0.00 21.80 50.02T15CA022 9.48 1.49 10.40 1.65 0.00 0.00 16.25 39.27 11.85 1.52 13.46 2.14 0.00 0.00 23.08 52.05T15CA023 24.23 3.81 19.07 3.03 0.00 0.00 41.53 91.67 30.28 3.87 24.68 3.93 0.00 0.00 59.01 121.77T15CA024 12.11 1.91 12.72 2.02 0.00 0.00 20.76 49.52 15.14 1.94 16.46 2.62 0.00 0.00 29.50 65.66T15CS004 7.72 1.21 7.75 1.23 0.00 0.00 13.23 31.14 9.65 1.23 10.02 1.59 0.00 0.00 18.80 41.29T15CS007 13.47 2.12 13.76 2.19 0.00 0.00 23.09 54.63 16.84 2.15 17.80 2.83 0.00 0.00 32.81 72.43T15JD005 6.17 0.97 8.09 1.29 0.00 0.00 10.58 27.10 7.71 0.99 10.47 1.67 0.00 0.00 15.03 35.87T15JD006 7.34 1.16 8.55 1.36 0.00 0.00 12.58 30.99 9.18 1.17 11.07 1.76 0.00 0.00 17.88 41.06T15JD007 8.43 1.33 10.40 1.65 0.00 0.00 14.46 36.27 10.54 1.35 13.46 2.14 0.00 0.00 20.54 48.03T15JD008 14.90 2.35 16.18 2.57 0.00 0.00 25.55 61.55 18.63 2.38 20.94 3.33 0.00 0.00 36.30 81.58T15JD009 15.68 2.47 16.18 2.57 0.00 0.00 26.88 63.78 19.60 2.51 20.94 3.33 0.00 0.00 38.19 84.57T15JD010 19.44 3.06 21.39 3.40 0.00 0.00 33.33 80.62 24.30 3.11 27.68 4.40 0.00 0.00 47.35 106.84T15JD011 21.05 3.31 21.39 3.40 0.00 0.00 36.08 85.23 26.31 3.36 27.68 4.40 0.00 0.00 51.26 113.01T15KM008 32.94 5.78 35.84 4.44 0.00 0.00 57.49 136.49 39.21 5.84 46.38 5.74 0.00 0.00 71.31 168.48

T20T20CA001 22.36 3.72 23.66 2.93 5.80 0.90 17.41 76.78 24.08 3.74 30.19 3.74 24.36 3.80 20.32 110.23T20CA002 32.12 5.42 33.43 4.14 11.36 1.77 25.07 113.31 34.59 5.45 42.65 5.28 47.73 7.45 29.25 172.40T20CA003 46.67 8.13 47.43 5.87 17.05 2.66 36.60 164.41 50.26 8.17 60.51 7.49 71.62 11.17 42.71 251.93

2 250

EP 1110-1-8, Vol. 430 Nov 11

2-308


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

T25T25CA006 18.81 2.21 28.14 3.48 0.00 0.00 20.63 73.27T25CA007 20.64 2.42 30.78 3.81 0.00 0.00 22.63 80.28T25CA008 22.36 2.63 37.21 4.61 0.00 0.00 24.52 91.33T25JD008 9.34 0.93 11.59 1.43 0.80 0.12 8.48 32.69T25JD009 11.44 1.14 18.45 2.28 0.80 0.12 10.38 44.61T25JD010 12.67 1.30 23.72 2.94 1.66 0.26 11.55 54.10T25JD012 17.63 1.93 34.26 4.24 4.61 0.72 16.25 79.64T25JD013 22.77 2.42 44.80 5.54 4.61 0.72 20.88 101.74T25JD014 17.24 1.73 28.99 3.59 1.66 0.26 15.67 69.14T25JD015 1.85 0.20 4.74 0.59 0.46 0.07 1.70 9.61T25JD016 2.79 0.29 5.90 0.73 0.46 0.07 2.55 12.79T25JD017 3.24 0.33 5.90 0.73 0.46 0.07 2.96 13.69T25JD018 4.06 0.41 7.06 0.87 0.46 0.07 3.70 16.63T25JD019 4.29 0.44 8.54 1.06 0.59 0.09 3.91 18.92T25JD020 4.10 0.48 9.59 1.19 1.78 0.28 3.82 21.24

T30T30DW005 3.61 0.40 4.43 0.55 0.29 0.05 4.50 13.83 4.82 0.41 5.85 0.72 1.08 0.17 6.66 19.71T30DW011 51.85 5.46 23.19 2.87 0.00 0.00 63.97 147.34 69.14 5.63 30.67 3.80 0.00 0.00 94.72 203.96T30DW012 0.93 0.10 3.41 0.42 0.01 0.00 1.14 6.01 1.23 0.10 4.45 0.55 0.06 0.01 1.69 8.09T30DW013 1.16 0.13 4.69 0.58 0.11 0.02 1.45 8.14 1.55 0.13 6.12 0.76 0.43 0.07 2.14 11.20T30DW014 12.35 1.33 10.75 1.33 0.51 0.08 15.30 41.65 16.46 1.37 14.22 1.76 1.89 0.29 22.65 58.64T30DW016 6.59 0.71 6.32 0.78 0.29 0.05 8.16 22.90 8.78 0.73 8.36 1.03 1.08 0.17 12.09 32.24T30DW017 7.78 0.85 8.22 1.02 0.51 0.08 9.66 28.12 10.37 0.87 10.87 1.35 1.89 0.29 14.31 39.95T30DW018 10.53 1.14 10.43 1.29 0.51 0.08 13.05 37.03 14.04 1.17 13.80 1.71 1.89 0.29 19.33 52.23T30TM007 48.09 5.06 23.19 2.87 0.00 0.00 59.33 138.54 64.12 5.22 30.67 3.80 0.00 0.00 87.85 191.66T30TM008 48.41 5.09 23.19 2.87 0.00 0.00 59.72 139.28 64.55 5.26 30.67 3.80 0.00 0.00 88.43 192.71

2 251

EP 1110-1-8, Vol. 430 Nov 11

2-309


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)11/30/2011

4REGION

T30 cont.T30TM012 82.18 8.65 40.58 5.01 0.00 0.00 101.39 237.81 109.57 8.92 53.67 6.64 0.00 0.00 150.12 328.92T30TM013 134.58 14.16 55.34 6.84 0.00 0.00 166.04 376.96 179.44 14.61 73.19 9.06 0.00 0.00 245.84 522.14T30TM014 128.83 13.56 55.34 6.84 0.00 0.00 158.94 363.51 171.77 13.99 73.19 9.06 0.00 0.00 235.32 503.33T30TM015 137.41 14.46 55.34 6.84 0.00 0.00 169.53 383.58 183.22 14.92 73.19 9.06 0.00 0.00 251.01 531.40T30VE007 19.01 2.00 13.18 1.63 0.00 0.00 23.46 59.28 25.35 2.06 17.43 2.16 0.00 0.00 34.73 81.73T30VE008 24.16 2.54 19.50 2.41 0.00 0.00 29.80 78.41 32.21 2.62 25.79 3.19 0.00 0.00 44.13 107.94T30VE009 39.17 4.12 26.35 3.26 0.00 0.00 48.33 121.23 52.23 4.25 34.85 4.31 0.00 0.00 71.56 167.20T30VE010 47.51 5.00 28.99 3.58 0.00 0.00 58.61 143.69 63.34 5.16 38.34 4.75 0.00 0.00 86.78 198.37

T35T35CT001 25.24 2.66 14.76 1.82 0.00 0.00 31.14 75.62 33.66 2.74 19.52 2.41 0.00 0.00 46.11 104.44T35CT002 31.09 3.27 14.76 1.82 0.00 0.00 38.36 89.30 41.45 3.38 19.52 2.41 0.00 0.00 56.79 123.55T35CT003 34.94 3.68 19.50 2.41 0.00 0.00 43.10 103.63 46.58 3.79 25.79 3.19 0.00 0.00 63.81 143.16T35CT004 32.90 3.46 10.75 1.33 0.00 0.00 40.58 89.02 43.86 3.57 14.22 1.76 0.00 0.00 60.09 123.50T35CT005 31.12 3.27 10.75 1.33 0.00 0.00 38.39 84.86 41.49 3.38 14.22 1.76 0.00 0.00 56.84 117.69T35CT006 31.12 3.27 10.75 1.33 0.00 0.00 38.39 84.86 41.49 3.38 14.22 1.76 0.00 0.00 56.84 117.69T35CT007 34.44 3.62 10.75 1.33 0.00 0.00 42.49 92.63 45.92 3.74 14.22 1.76 0.00 0.00 62.92 128.56T35CT008 44.14 4.65 15.81 1.95 0.00 0.00 54.46 121.01 58.86 4.79 20.91 2.58 0.00 0.00 80.63 167.77T35CT009 51.37 5.41 15.81 1.95 0.00 0.00 63.38 137.92 68.50 5.58 20.91 2.58 0.00 0.00 93.84 191.41T35CT010 50.33 5.30 15.81 1.95 0.00 0.00 62.09 135.48 67.10 5.46 20.91 2.58 0.00 0.00 91.93 187.98T35CT011 60.44 6.36 18.45 2.28 0.00 0.00 74.57 162.10 80.59 6.56 24.40 3.01 0.00 0.00 110.41 224.97

T40T40AG001 8.75 0.95 8.43 1.19 0.40 0.06 8.46 28.24T40AH001 2.81 0.30 0.00 0.25 0.00 0.00 3.09 6.45T40AH003 4.17 0.44 0.00 0.25 0.00 0.00 4.58 9.44T40AH004 5.16 0.54 0.00 0.25 0.00 0.00 5.66 11.61T40GN001 1.83 0.16 0.00 0.00 0.00 0.00 1.57 3.56 2.26 0.16 0.00 0.00 0.00 0.00 2.20 4.62

2 252

EP 1110-1-8, Vol. 430 Nov 11

2-310


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

T40 cont.T40KF011 0.46 0.05 0.00 0.00 0.00 0.00 0.38 0.89T40KF013 0.49 0.05 0.00 0.00 0.00 0.00 0.41 0.95T40KF014 0.54 0.06 0.00 0.00 0.00 0.00 0.44 1.04T40KF016 0.65 0.07 0.00 0.00 0.00 0.00 0.53 1.25T40KF018 0.77 0.08 0.00 0.00 0.00 0.00 0.63 1.48T40KF020 0.92 0.10 0.00 0.00 0.00 0.00 0.76 1.78T40KF021 0.46 0.05 0.00 0.10 0.00 0.00 0.44 1.05T40KF022 0.82 0.09 0.00 0.10 0.00 0.00 0.79 1.80T40KF023 0.33 0.03 0.00 0.05 0.00 0.00 0.32 0.73T40KF024 0.48 0.05 0.00 0.05 0.00 0.00 0.46 1.04T40MY002 0.61 0.05 0.00 0.00 0.00 0.00 0.52 1.18 0.75 0.05 0.00 0.00 0.00 0.00 0.73 1.53T40MY003 0.76 0.07 0.00 0.00 0.00 0.00 0.65 1.48 0.93 0.07 0.00 0.00 0.00 0.00 0.91 1.91T40MY004 0.88 0.08 0.00 0.00 0.00 0.00 0.75 1.71 1.08 0.08 0.00 0.00 0.00 0.00 1.05 2.21T40MY005 1.23 0.11 0.00 0.00 0.00 0.00 1.05 2.39 1.52 0.11 0.00 0.00 0.00 0.00 1.48 3.11T40MY006 1.41 0.12 0.00 0.00 0.00 0.00 1.20 2.73 1.73 0.13 0.00 0.00 0.00 0.00 1.69 3.55T40PA001 0.74 0.08 0.00 0.24 0.00 0.00 0.81 1.87T40PA002 4.06 0.43 0.00 0.24 0.00 0.00 4.47 9.20T40PA003 4.79 0.50 0.00 0.26 0.00 0.00 5.26 10.81T40PA004 5.25 0.55 0.00 0.26 0.00 0.00 5.77 11.83T40PA005 9.32 0.98 0.00 0.27 0.00 0.00 10.24 20.81T40PA006 11.14 1.17 0.00 0.27 0.00 0.00 12.24 24.82T40RS001 2.85 0.33 0.00 0.00 0.00 0.00 2.51 5.69T40RS002 2.94 0.34 0.00 0.00 0.00 0.00 2.59 5.87T40RS003 3.17 0.37 0.00 0.00 0.00 0.00 2.78 6.32T40XX034 16.38 1.57 28.41 4.01 0.00 0.00 14.82 65.19T40XX035 16.64 1.60 30.23 4.26 0.00 0.00 15.06 67.79T40XX036 19.96 1.91 34.46 4.86 0.00 0.00 18.06 79.25

2 253

EP 1110-1-8, Vol. 430 Nov 11

2-311


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)11/30/2011

4REGION

T40 cont.T40XX037 19.60 1.88 34.46 4.86 0.00 0.00 17.73 78.53T40XX038 20.51 1.97 34.46 4.86 0.00 0.00 18.56 80.36

T45T45EA006 3.63 0.45 0.00 0.50 1.58 0.25 2.25 8.66T45EA007 4.81 0.61 0.00 0.50 2.37 0.37 2.99 11.65T45G1001 8.04 1.14 7.91 0.84 0.00 0.00 8.24 26.17T45MY004 2.50 0.31 0.00 0.30 1.13 0.18 2.17 6.59 3.13 0.32 0.00 0.30 4.12 0.64 3.11 11.62T45MY005 3.31 0.42 0.00 0.30 1.69 0.26 2.88 8.86 4.14 0.43 0.00 0.30 6.18 0.96 4.12 16.13T45MY006 3.42 0.44 0.00 0.30 1.69 0.26 2.98 9.09 4.27 0.45 0.00 0.30 6.18 0.96 4.25 16.41T45MY007 3.29 0.42 0.00 0.30 1.69 0.26 2.87 8.83 4.12 0.43 0.00 0.30 6.18 0.96 4.10 16.09T45MY015 2.70 0.34 0.00 0.40 1.13 0.18 2.18 6.93 3.38 0.34 0.00 0.40 4.12 0.64 3.14 12.02T45MY016 2.76 0.34 0.00 0.40 1.13 0.18 2.23 7.04 3.45 0.35 0.00 0.40 4.12 0.64 3.21 12.17T45MY017 2.90 0.38 0.00 0.40 1.69 0.26 2.35 7.98 3.62 0.39 0.00 0.40 6.18 0.96 3.39 14.94T45MY018 2.10 0.23 0.00 0.40 1.13 0.18 1.57 5.61T45MY019 2.08 0.23 0.00 0.40 1.13 0.18 1.56 5.58T45XX001 3.27 0.39 0.00 0.40 0.91 0.14 2.83 7.94 4.09 0.40 0.00 0.40 3.31 0.52 4.04 12.76T45XX003 4.50 0.52 0.00 0.40 0.91 0.14 3.87 10.34 5.62 0.53 0.00 0.40 3.31 0.52 5.53 15.91T45XX008 2.70 0.33 0.00 0.40 0.91 0.14 2.17 6.65 3.37 0.33 0.00 0.40 3.31 0.52 3.13 11.06T45XX009 3.43 0.34 0.00 0.40 0.91 0.14 2.54 7.76T45XX010 3.44 0.34 0.00 0.40 0.91 0.14 2.55 7.78T45XX011 2.76 0.33 0.00 0.40 0.80 0.12 1.70 6.11T45XX012 2.95 0.35 0.00 0.40 0.80 0.12 1.82 6.44T45XX013 3.07 0.37 0.00 0.40 0.91 0.14 1.89 6.78T45XX014 3.71 0.45 0.00 0.50 1.20 0.19 2.29 8.34T45XX015 3.81 0.46 0.00 0.50 1.20 0.19 2.35 8.51T45XX016 4.25 0.51 0.00 0.50 1.36 0.21 2.63 9.46T45XX017 4.47 0.54 0.00 0.50 1.58 0.25 2.76 10.10

2 254

EP 1110-1-8, Vol. 430 Nov 11

2-312


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

T45 cont.T45XX018 4.52 0.55 0.00 0.50 1.58 0.25 2.79 10.19T45XX019 5.25 0.63 0.00 0.50 1.58 0.25 3.24 11.45T45XX020 5.01 0.61 0.00 0.60 1.81 0.28 3.10 11.41T45XX021 5.50 0.66 0.00 0.60 1.81 0.28 3.40 12.25T45XX022 6.17 0.75 0.00 0.60 2.11 0.33 3.82 13.78T45XX023 7.37 0.89 0.00 0.60 2.57 0.40 4.55 16.38T45XX024 2.33 0.29 0.00 0.09 0.91 0.14 1.45 5.21T45XX025 2.56 0.31 0.00 0.10 0.91 0.14 1.58 5.60T45XX026 1.46 0.18 0.00 0.40 0.47 0.07 0.90 3.48T45XX027 1.63 0.20 0.00 0.40 0.58 0.09 1.01 3.91T45XX028 1.81 0.23 0.00 0.40 0.85 0.13 1.13 4.55T45XX029 6.14 0.90 6.64 0.70 0.45 0.07 5.44 20.34T45XX030 5.96 0.90 6.64 0.70 0.91 0.14 5.31 20.56T45XX031 7.31 1.09 6.64 0.70 0.91 0.14 6.50 23.29T45XX032 4.53 0.43 0.00 0.50 0.68 0.11 3.34 9.59T45XX033 5.29 0.50 0.00 0.60 0.91 0.14 3.90 11.34T45XX034 2.51 0.31 0.00 0.40 0.91 0.14 1.55 5.82T45XX035 2.69 0.32 0.00 0.40 0.91 0.14 1.66 6.12

T50T50GM001 1.63 0.18 6.06 0.75 0.21 0.03 1.63 10.49 2.01 0.18 7.80 0.96 0.68 0.11 2.15 13.89T50GM004 3.73 0.40 14.40 1.78 0.21 0.03 3.71 24.26 4.59 0.41 18.52 2.29 0.68 0.11 4.89 31.49T50GM005 4.01 0.43 14.40 1.78 0.22 0.03 3.99 24.86 4.94 0.44 18.52 2.29 0.76 0.12 5.26 32.33T50XX001 1.55 0.18 6.57 0.81 0.29 0.05 1.56 11.01 1.91 0.18 8.45 1.04 0.97 0.15 2.05 14.75T50XX002 1.91 0.21 6.57 0.81 0.19 0.03 1.91 11.63 2.35 0.21 8.45 1.04 0.63 0.10 2.52 15.30T50XX003 2.17 0.24 9.10 1.12 0.22 0.03 2.17 15.05 2.67 0.24 11.70 1.45 0.72 0.11 2.86 19.75T50XX004 1.88 0.21 6.57 0.81 0.31 0.05 1.89 11.72 2.32 0.21 8.45 1.04 1.08 0.17 2.49 15.76T50XX005 2.27 0.25 6.57 0.81 0.20 0.03 2.26 12.39 2.79 0.25 8.45 1.04 0.69 0.11 2.98 16.31

2 255

EP 1110-1-8, Vol. 430 Nov 11

2-313


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)11/30/2011

4REGION

T50 cont.T50XX006 2.33 0.25 9.10 1.12 0.23 0.04 2.33 15.40 2.87 0.26 11.70 1.45 0.80 0.12 3.07 20.27T50XX007 1.64 0.18 6.57 0.81 0.29 0.05 1.65 11.19 2.02 0.19 8.45 1.04 0.97 0.15 2.17 14.99T50XX008 2.04 0.22 6.57 0.81 0.19 0.03 2.03 11.89 2.51 0.23 8.45 1.04 0.63 0.10 2.68 15.64T50XX009 2.50 0.27 9.10 1.12 0.22 0.03 2.49 15.73 3.08 0.28 11.70 1.45 0.72 0.11 3.29 20.63T50XX010 2.25 0.25 6.57 0.81 0.31 0.05 2.26 12.50 2.77 0.25 8.45 1.04 1.08 0.17 2.97 16.73T50XX011 2.47 0.27 9.10 1.12 0.20 0.03 2.46 15.65 3.04 0.27 11.70 1.45 0.69 0.11 3.25 20.51T50XX012 2.57 0.28 9.10 1.12 0.23 0.04 2.57 15.91 3.17 0.29 11.70 1.45 0.80 0.12 3.38 20.91T50XX013 2.03 0.23 2.05 0.22 0.29 0.05 2.04 6.91 2.50 0.23 2.93 0.31 0.97 0.15 2.69 9.78T50XX014 2.31 0.25 2.05 0.22 0.19 0.03 2.30 7.35 2.84 0.26 2.93 0.31 0.63 0.10 3.03 10.10T50XX015 2.66 0.29 3.55 0.38 0.22 0.03 2.65 9.78 3.27 0.29 5.07 0.54 0.72 0.11 3.49 13.49T50XX016 2.44 0.27 3.55 0.38 0.31 0.05 2.44 9.44 3.01 0.28 5.07 0.54 1.08 0.17 3.22 13.37T50XX017 2.51 0.27 3.55 0.38 0.20 0.03 2.50 9.44 3.09 0.28 5.07 0.54 0.69 0.11 3.29 13.07T50XX018 3.00 0.32 3.55 0.38 0.23 0.04 2.99 10.51 3.69 0.33 5.07 0.54 0.80 0.12 3.94 14.49T50XX019 2.40 0.26 3.55 0.38 0.19 0.03 2.39 9.20 2.95 0.27 5.07 0.54 0.63 0.10 3.15 12.71T50XX020 2.91 0.31 3.55 0.38 0.20 0.03 2.90 10.28 3.58 0.32 5.07 0.54 0.69 0.11 3.82 14.13T50XX021 2.62 0.29 3.55 0.38 0.22 0.03 2.62 9.71 3.23 0.29 5.07 0.54 0.72 0.11 3.45 13.41T50XX022 4.17 0.56 11.93 1.37 0.42 0.07 3.86 22.38 5.21 0.57 15.44 1.77 1.64 0.26 5.20 30.09T50XX023 3.25 0.44 24.26 3.21 0.42 0.07 3.02 34.67 4.06 0.45 31.08 4.11 1.64 0.26 4.06 45.66T50XX024 2.81 0.38 24.26 3.21 0.42 0.07 2.61 33.76 3.51 0.39 31.08 4.11 1.64 0.26 3.52 44.51T50XX025 5.45 0.73 11.27 1.29 0.69 0.11 5.05 24.59 6.81 0.75 14.59 1.68 2.85 0.44 6.81 33.93T50XX026 5.54 0.75 13.92 1.60 0.66 0.10 5.14 27.71 6.93 0.76 18.02 2.07 2.56 0.40 6.92 37.66T50XX027 7.44 1.17 24.80 3.06 0.62 0.10 6.88 44.07 8.93 1.18 32.04 3.96 2.34 0.37 9.53 58.35T50XX028 7.36 1.17 21.53 2.66 0.94 0.15 6.82 40.63 8.83 1.19 27.81 3.44 3.61 0.56 9.45 54.89T50XX029 6.77 1.08 29.02 3.59 0.94 0.15 6.28 47.83 8.12 1.09 37.48 4.63 3.61 0.56 8.69 64.18T50XX030 8.70 1.38 32.76 4.05 0.94 0.15 8.06 56.04 10.44 1.39 42.32 5.23 3.61 0.56 11.15 74.70T50XX031 8.02 1.27 37.44 4.63 0.85 0.13 7.43 59.77 9.62 1.28 48.36 5.98 3.27 0.51 10.28 79.30T50XX032 8.10 1.27 24.80 3.06 0.62 0.10 7.49 45.44 9.72 1.28 32.04 3.96 2.34 0.37 10.36 60.07

2 256

EP 1110-1-8, Vol. 430 Nov 11

2-314


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

T50 cont.T50XX033 8.77 1.38 37.44 4.63 0.85 0.13 8.12 61.32 10.52 1.40 48.36 5.98 3.27 0.51 11.24 81.28T50XX035 7.78 1.03 13.92 1.60 0.66 0.10 7.20 32.29 9.73 1.06 18.02 2.07 2.56 0.40 9.70 43.54

T55T55CA002 36.60 8.83 37.57 5.63 13.31 2.08 42.09 146.11 40.66 8.87 48.62 7.28 52.34 8.17 49.38 215.32T55CA003 50.10 12.19 54.22 8.12 20.61 3.22 57.71 206.17 55.67 12.25 70.16 10.51 81.10 12.65 67.70 310.04T55CA007 27.70 6.60 28.15 4.22 14.57 2.27 31.79 115.30 30.78 6.63 36.43 5.46 57.32 8.94 37.30 182.86T55CA008 26.91 4.25 21.22 1.77 8.69 1.36 27.43 91.63 28.56 4.28 25.64 2.13 33.64 5.25 30.94 130.44T55CA009 31.58 5.04 23.26 1.94 12.02 1.88 32.24 107.96 33.51 5.06 28.10 2.34 46.49 7.25 36.36 159.11T55CA010 27.24 4.24 17.46 1.45 6.43 1.00 27.70 85.52 28.91 4.26 21.10 1.76 25.28 3.94 31.24 116.49T55CA011 32.38 5.01 21.22 1.77 6.60 1.03 32.89 100.90 34.36 5.04 25.64 2.13 25.94 4.05 37.10 134.26T55CA012 38.94 6.17 28.97 2.41 13.35 2.08 39.70 131.62 41.32 6.20 35.00 2.91 52.51 8.19 44.78 190.91T55CA013 42.52 6.79 33.05 2.75 16.90 2.64 43.41 148.06 45.12 6.82 39.93 3.32 66.93 10.44 48.96 221.52T55JD001 21.05 3.32 21.62 1.80 6.60 1.03 21.45 76.87 22.34 3.33 26.13 2.17 25.94 4.05 24.19 108.15T55JD002 24.43 3.82 23.26 1.94 6.60 1.03 24.86 85.94 25.93 3.84 28.10 2.34 25.94 4.05 28.05 118.25T55JD003 29.80 4.95 31.01 2.58 18.94 2.95 30.62 120.85 31.63 4.97 37.47 3.12 74.48 11.62 34.53 197.82T55JD004 34.14 5.55 33.70 2.80 17.26 2.69 34.95 131.09 36.23 5.58 40.72 3.39 67.89 10.59 39.43 203.83T55KM009 19.37 4.72 28.21 4.22 14.57 2.27 22.32 95.68 21.52 4.75 36.50 5.47 57.32 8.94 26.18 160.68T55KM012 38.79 9.65 60.23 9.02 20.61 3.22 44.83 186.35 43.10 9.70 77.94 11.67 81.10 12.65 52.59 288.75T55KM013 93.31 22.25 85.89 12.86 28.19 4.40 107.11 354.01 103.67 22.36 111.15 16.65 110.90 17.30 125.66 507.69T55KM014 104.93 26.27 115.60 17.31 59.36 9.26 121.40 454.13 116.59 26.40 149.60 22.40 233.50 36.43 142.42 727.34T55KM015 22.34 3.83 31.74 2.64 18.94 2.95 23.07 105.51 23.71 3.85 38.36 3.19 74.48 11.62 26.02 181.23T55KM016 29.43 4.85 35.09 2.92 17.26 2.69 30.19 122.43 31.23 4.87 42.40 3.53 67.89 10.59 34.05 194.56T55VO002 23.85 3.79 24.40 2.03 8.57 1.34 24.33 88.31 25.31 3.80 29.48 2.45 33.88 5.29 27.44 127.65T55VO003 25.49 3.99 24.40 2.03 7.05 1.10 25.95 90.01 27.05 4.01 29.48 2.45 27.73 4.33 29.26 124.31T55VO004 36.47 5.80 33.78 2.81 13.35 2.08 37.20 131.49 38.70 5.83 40.82 3.40 52.51 8.19 41.96 191.41T55VO005 30.54 4.69 27.42 2.28 4.09 0.64 30.98 100.64 32.41 4.71 33.13 2.76 16.10 2.51 34.95 126.57T55VO006 39.85 6.44 37.86 3.15 18.45 2.88 40.76 149.39 42.29 6.47 45.75 3.81 72.57 11.32 45.97 228.18

2 257

EP 1110-1-8, Vol. 430 Nov 11

2-315


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)11/30/2011

4REGION

T56T56CA006 56.26 13.58 60.59 9.07 22.63 3.53 64.71 230.37 62.51 13.65 98.87 13.94 88.38 13.79 75.91 367.05

T57T57CU001 9.59 1.24 8.01 0.99 0.38 0.06 10.55 30.82T57CU002 11.79 1.53 8.01 0.99 0.38 0.06 12.96 35.72T57CU003 10.10 1.31 31.62 3.91 0.38 0.06 11.11 58.49T57CU004 11.20 1.45 36.89 4.56 0.38 0.06 12.32 66.86T57CU005 13.26 1.72 44.80 5.54 0.38 0.06 14.58 80.34

T60T60KI001 18.07 2.87 18.45 2.60 3.19 0.50 17.12 62.80 21.68 2.90 24.40 3.44 12.11 1.89 23.46 89.88T60KI002 27.12 4.45 34.78 4.90 10.02 1.56 25.87 108.70 32.55 4.51 46.00 6.49 38.68 6.03 35.47 169.73T60KI003 43.38 7.18 47.43 6.69 18.10 2.82 41.46 167.06 52.06 7.27 62.73 8.85 69.84 10.90 56.83 268.48T60KI004 6.33 1.52 47.43 6.69 18.10 2.82 6.63 89.52 7.59 1.54 62.73 8.85 69.84 10.90 9.09 170.54T60KI006 52.67 8.71 57.97 8.18 21.70 3.39 50.33 202.95 63.20 8.82 76.67 10.81 83.73 13.06 68.98 325.27T60SO001 31.73 5.16 34.78 4.90 10.02 1.56 30.20 118.35 38.07 5.22 46.00 6.49 38.68 6.03 41.40 181.89T60SO002 42.99 7.13 47.43 6.69 18.40 2.87 41.11 166.62 51.59 7.22 62.73 8.85 71.04 11.08 56.35 268.86T60SO003 43.70 7.24 47.43 6.69 18.40 2.87 41.77 168.10 52.44 7.33 62.73 8.85 71.04 11.08 57.26 270.73T60SO004 54.74 9.00 57.97 8.18 20.75 3.24 52.23 206.11 65.68 9.11 76.67 10.81 80.09 12.49 71.60 326.45T60SO005 55.72 9.15 57.97 8.18 20.75 3.24 53.16 208.17 66.87 9.27 76.67 10.81 80.09 12.49 72.87 329.07

T65T65WG012 104.02 16.78 13.42 6.03 2.90 0.45 120.91 264.51T65WG013 156.75 25.23 13.42 6.03 2.90 0.45 182.13 386.91T65WG014 170.82 27.48 29.19 14.13 2.90 0.45 198.47 443.44

W25W25AO002 0.87 0.05 0.08 0.79 0.00 0.00 1.32 3.11

2 258

EP 1110-1-8, Vol. 430 Nov 11

2-316


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

W25 cont.W25AO003 1.27 0.07 0.08 0.79 0.00 0.00 1.92 4.13W25AO004 1.25 0.07 0.15 1.07 0.00 0.00 1.89 4.43W25AO005 2.53 0.15 0.31 1.64 0.00 0.00 3.82 8.45W25AO006 1.96 0.11 0.08 0.79 0.00 0.00 2.95 5.89W25CJ001 10.32 0.84 1.13 0.62 0.00 0.00 14.16 27.07W25CJ002 16.02 1.30 1.36 0.75 0.00 0.00 21.99 41.42W25CJ003 25.32 2.06 1.36 0.75 0.00 0.00 34.76 64.25W25KZ001 1.41 0.25 0.00 0.00 0.00 0.00 0.95 2.61W25KZ002 1.56 0.27 0.00 0.00 0.00 0.00 1.05 2.88W25KZ003 1.59 0.28 0.00 0.00 0.00 0.00 1.08 2.95W25KZ004 2.27 0.40 0.00 0.00 0.00 0.00 1.53 4.20W25KZ005 2.68 0.47 0.00 0.00 0.00 0.00 1.81 4.96W25KZ006 2.73 0.48 0.00 0.00 0.00 0.00 1.84 5.05W25KZ007 2.91 0.51 0.00 0.00 0.00 0.00 1.97 5.39W25NL001 14.99 0.86 15.39 6.79 0.00 0.00 24.69 62.72W25NL002 25.24 1.45 51.26 6.33 0.00 0.00 41.58 125.86W25NL003 16.17 0.93 22.95 2.84 0.00 0.00 26.65 69.54W25NL004 32.64 1.91 5.20 0.64 0.49 0.08 53.95 94.91W25NL005 61.93 3.57 107.10 13.23 0.00 0.00 102.03 287.86W25SD001 1.09 0.06 0.38 0.17 0.00 0.00 1.65 3.35W25SD002 2.82 0.16 0.23 0.10 0.00 0.00 4.25 7.56W25SD003 1.69 0.10 5.59 0.59 0.00 0.00 2.55 10.52W25SD004 2.42 0.14 2.48 0.26 0.04 0.01 3.67 9.02W25SD005 1.28 0.07 3.73 0.39 0.00 0.00 1.93 7.40W25SD006 1.16 0.07 0.08 4.04 0.00 0.00 1.75 7.10W25SD007 1.24 0.07 0.08 5.04 0.00 0.00 1.87 8.30W25SD008 1.35 0.08 0.08 6.04 0.00 0.00 2.03 9.58

2 259

EP 1110-1-8, Vol. 430 Nov 11

2-317


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)11/30/2011

4REGION

W25 cont.W25SD009 2.99 0.17 0.85 6.37 0.00 0.00 4.51 14.89W25XX005 0.41 0.02 1.55 0.16 0.00 0.00 0.62 2.76W25XX006 0.57 0.03 1.55 0.16 0.00 0.00 0.86 3.17W25XX007 0.76 0.04 2.48 0.26 0.00 0.00 1.15 4.69W25XX008 0.80 0.05 3.42 0.36 0.00 0.00 1.20 5.83W25XX009 1.60 0.09 2.48 0.26 0.00 0.00 2.41 6.84W25XX010 2.45 0.14 7.45 0.79 0.00 0.00 3.69 14.52

W30W30SO001 3.64 0.58 1.70 0.19 0.40 0.06 2.95 9.52W30SO002 4.37 0.69 1.70 0.19 0.40 0.06 3.54 10.95W30SO003 4.76 0.75 1.70 0.19 0.40 0.06 3.86 11.72W30SO004 2.41 0.37 0.00 0.01 0.00 0.00 1.62 4.41W30SO005 2.69 0.41 0.00 0.01 0.00 0.00 1.81 4.92W30SO006 3.10 0.47 0.00 0.01 0.00 0.00 2.08 5.66

W35W35LC010 0.09 0.01 0.36 0.16 0.00 0.00 0.06 0.68W35LC011 0.43 0.04 0.66 0.29 0.00 0.00 0.30 1.72W35LC012 0.56 0.05 0.85 0.37 0.00 0.00 0.38 2.21W35LC013 0.60 0.05 1.00 0.44 0.00 0.00 0.41 2.50W35LC018 0.11 0.01 0.12 0.05 0.00 0.00 0.08 0.37W35LC020 0.54 0.04 0.63 0.28 0.00 0.00 0.37 1.86W35XX020 0.24 0.03 2.86 0.30 0.00 0.00 0.26 3.69W35XX021 0.61 0.07 4.42 0.47 0.03 0.00 0.67 6.27W35XX022 0.63 0.07 4.68 0.49 0.03 0.00 0.69 6.59W35XX023 1.10 0.13 11.70 1.24 0.03 0.00 1.21 15.41W35XX024 1.63 0.19 6.20 0.66 0.03 0.00 1.80 10.51

2 260

EP 1110-1-8, Vol. 430 Nov 11

2-318


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 4)

11/30/2011

4REGION

W35 cont.W35XX025 1.56 0.18 5.43 0.57 0.03 0.00 1.72 9.49

2 261

EP 1110-1-8, Vol. 430 Nov 11

2-319


EP 1110-1-8, Vol. 430 Nov 11

2-320

3-1

CHAPTER 3

Adjustments to Hourly Rates

SECTION I. GENERAL

3.1 Contents. This chapter explains the procedures for adjusting the hourly rates shown in tables 2-1 and 2-2.

3.2 Basis for Equipment Rates. The rates shown in tables 2-1 and 2-2 are based on the catalog list price of equipment manufactured in 2008 (3 years old). Area factors used to compute regional ownership and operating expenses are listed in appendix B. All equipment hourly rate elements for average and severe conditions are given in table 2-2. Individual cost elements, which comprise the total hourly rate, are shown in table 2-2. These hourly rate elements are listed by equipment ID No., which corresponds to the equipment shown in tables 2-1 and 2-2.

a. Ownership costs consist of two cost elements: depreciation (DEPR) and facilities capital cost of money (FCCM). These elements are located in tables 2-1 and 2-2.

b. Operating costs consist of five cost elements: fuel (FUEL); filters, oil, and grease (FOG); repairs (REPAIR); tire wear (TIRE WEAR); and tire repair (TIRE REPAIR). These elements are located in table 2-2.

3.3 Equipment Rate Adjustment Tables. Table 3-1 is used to adjust the ownership (DEPR + FCCM) portion of the average hourly rate and table 3-2 is used to adjust the standby hourly rate shown in table 2-1.

3.4 Determination for Use of Equipment Rates in Tables 2-1 and 2-2. The predetermined equipment rates in tables 2-1 and 2-2 may be used when the contractor’s actual cost data (cost or pricing data) is insufficient to calculate the rates. If the contractor’s actual equipment is listed in tables 2-1 and 2-2, the equipment must be equivalent. However, if the contractor’s actual equipment is not listed in tables 2-1 and 2-2, an equivalent piece of equipment may be chosen from the tables. To be considered equivalent, the contractor’s equipment must be no more or less than 10.00 percent of the configuration (size, capacity, and horsepower) and value as compared to the equipment in tables 2-1 and 2-2. In either case, if the equipment is not equivalent, the equipment rate must be calculated using the methodology in chapter 2.

SECTION II. RATE ADJUSTMENTS

3.5 Rate Adjustments. The ownership and/or the operating portion of the hourly rates and standby hourly rates shall be adjusted whenever one or more of the following rate

EP 1110-1-8, Vol. 430 Nov 11

3-2

adjustment conditions exist (rate adjustments are explained in detail in the following paragraphs).

a. Changes in operating conditions. b. Changes in Cost of Money Rate. c. Actual work hours (hrs) exceed 40 hr per week (wk). d. Changes in FUEL cost. e. Adjustments to FOG cost. f. Equipment of different age than table 2-1. g. Rate adjustment for overage equipment. h. Rate adjustment for overage equipment standby.

There are no rate adjustments for appendix B factors except for fuel cost (electric, gas, diesel off-road, and diesel on-road) and the Cost of Money Rate. Also, there are no rate adjustments for repairs, tire wear, or tire repair.

3.6 Changes in Operating Conditions. If difficult or severe conditions are justified by the Contracting Officer, selection or calculation of the appropriate rate is necessary. See chapter 2, section II, for definition of average, difficult, or severe conditions and determination of condition.

3.7 Change in Cost of Money Rate (CMR). The Department of the Treasury adjusts the CMR (Prompt Payment Interest Rate) on or about 1 January and 1 July each year; these revisions are printed in the Federal Register. The Internet address for Prompt Payment Interest Rate is http://www.treasurydirect.gov/govt/rates/tcir/tcir_ opdprmt2.htm. If the CMR shown in chapter 2, section VII, is not the current rate, the FCCM portion of the total hourly rate shall be adjusted upward or downward to match the CMR for the period of equipment use. See appendix I for a listing of historical CMRs. The total hourly rate adjusted for a differing CMR is computed by the formula:

Example: Assume that table 2-1 includes a crane [category (CAT) C80, subcategory (SUB) 0.02] with hourly costs as shown in the following example. The CMR has increased from 5.00 percent to a current rate of 6.00 percent (increase of 20.00 percent). The total hourly rate for this piece of equipment is determined as follows:

Assumptions for Total Hourly Rate with CMR of 5.00 percent (per hour):

DEPR $30.00 FCCM $10.00 Operating Costs (FUEL, FOG, TIRE WEAR, TIRE REPAIR, and REPAIR) $40.00 Total Hourly Rate (Based on a 40 hr/wk) $80.00

Costs/hr Operating ]CMR) (OldCMR) (NEW x [(FCCM/hr) DEPR/hr Rate Hourly Total

EP 1110-1-8, Vol. 430 Nov 11

3-3

Adjustment Calculation of Total Hourly Rate for New CMR of 6.00 percent (per hour):

3.8 Actual Work Hours Greater than 40 Hours per Week. If the actual number of work hours per week is greater than 40 hours, an adjustment shall be made to the FCCM element of the ownership cost. The FCCM is to be paid up to a maximum of 40 hours per week (7 calendar days). To calculate a multi-shift rate, prorate the 40-hour FCCM over the actual hours per week, as follows:

Example: Assume that table 2-1 includes a crane (category C80, subcategory 0.02) with the below hourly costs. This crane worked 10 hours per day, 6 days per week (60 hours per week). The total hourly rate for this piece of equipment is determined as follows:

Assumptions for Total Hourly Rate for 40 Hours/Week:

DEPR $30.00 FCCM $10.00 Operating Costs (FUEL, FOG, TIRE WEAR, TIRE REPAIR, and REPAIR) $40.00 Total Hourly Rate (Based on a 40 hr/wk) $80.00

Adjustment Calculation of Total Hourly Rate for 60 Hours/Week:

3.9 Changes in Fuel Cost. Hourly fuel costs (including electricity) shall be adjusted in the event the average fuel prices at the jobsite vary by more than 10.00 percent above or below the price in appendix B. The contractor shall be required to furnish copies of all fuel supply contracts and invoices to the government to support fuel cost adjustment. Request for upward adjustment in the rates will be considered only when fuel is supplied by recognized distributors of bulk quantities. Mathematically, this is the ratio of the new fuel cost divided by the fuel cost (appendix B). To calculate the total hourly rate, apply the ratio of fuel cost, as follows:

$76.67/hr $40.00/hr ]hr/wk) (60hr/wk) (40x )[$10.00/hr $30.00/hr

Costs/hr Operating ]hr/wk) Work (Actual

hr/wk) (40 x [(FCCM/hr) DEPR/hr Rate Hourly Total

$82.00/hr $40.00/hr ](5.00%)(6.00%) x r)[($10.00/h $30.00/hr

EP 1110-1-8, Vol. 430 Nov 11

3-4

Example: Assume that table 2-1 includes a crane (category C80, subcategory 0.02) with the below hourly costs. Assume the fuel cost (diesel off-road) in appendix B is $3.50/gal and the current fuel cost has increased to $4.20/gal (increase of 20.00 percent). The total hourly rate for this piece of equipment can be determined as follows:

Assumptions for Fuel Cost (based on $3.50/gal from appendix B) per hour:

DEPR $30.00 FCCM $10.00 FOG, TIRE WEAR, TIRE REPAIR, and REPAIR $30.00 FUEL $10.00 Total Hourly Rate $80.00

Adjustment Calculation for hourly FUEL cost using the new fuel cost of $3.00/gal:

3.10 Adjustments to Fuel, Oil, and Grease (FOG) Cost. The hourly FOG allowance shall also be adjusted upward or downward by applying the same ratio (new fuel cost divided by fuel cost shown in appendix B) as the fuel costs change using the methodology as shown in paragraph 3.9.

3.11 Equipment of Different Age than Table 2-1. When the age of the equipment is newer or older than the age of the equipment listed in table 2-1, table 3-1 factors may be used to adjust the hourly rate (see paragraph 3.12 for guidance on overage equipment), otherwise the step-by-step calculation method (as shown in figure 2-1) is necessary. To adjust the hourly rate using the tables, the factors given in table 3-1 are multiplied by the hourly ownership costs shown in table 2-1. The result is an ownership rate adjusted for the actual age of the equipment. Note: Age adjustment factors in tables 3-1 and 3-2 vary by region.

a. When the age of a unit of equipment is older than the age of the equipment listed in table 2-1 (purchased new in 2008) and does not exceed the years of economic life, adjust the hourly rate as shown in the next example. The years of economic life is determined by dividing hours of LIFE (from appendix D) by Working Hours Per Year (WHPY) (from appendix B).

FUEL/hr] x

B Appendix in Cost FuelCost FuelNew [ REPAIR/hr)

REPAIR/hr TIRE WEAR/hrTIRE (FOG/hr FCCM/hr) (DEPR/hr RateHourly Total

$82.00/hr $10.00/hr] x )($3.50/gal)($4.20/gal[ $30.00/hr $10.00/hr) ($30.00/hr

EP 1110-1-8, Vol. 430 Nov 11

3-5

Example: Assume that table 2-1 includes a crane (category C80, subcategory 0.02) manufactured in 2008 and has a total hourly rate of $65 per hour and an ownership rate of $30 per hour. If an equivalent crane owned by a contractor was manufactured in 2004, the total hourly rate is determined as follows:

Table 2-1 Rate and Adjustment Calculation:

Total hourly rate = $65.00/hr Ownership rate 2008 (DEPR + FCCM) = -($30.00)/hr Ownership rate 2004 adjusted for age (Ownership rate = $30) x (0.86 the age adjustment factor from table 3-1, for category C80, subcategory 0.02, and for the year 2004.) = +$25.80/hr Total hourly rate for equipment manufactured in 2004 = $60.80/hr

b. When the unit of equipment is older than the age of equipment listed in table 2-1 (purchased new in 2008) and exceeds the years of economic life, adjust the hourly rate as shown in the example for overage equipment in paragraph 3.12.

c. When the unit of equipment is newer than the equipment listed in table 2-1 (purchased new in 2008), use the adjustment factor in table 3-1 for the year of manufacture. If the equipment is newer than the most recent year shown in table 3-1, use the adjustment factor in the column of the most recent year. Once the adjustment factor is determined from table 3-1, complete the adjustment calculation as shown in the example above. The step-by-step calculation method shown in figure 2-1 may also be used.

3.12 Rate Adjustment for Overage Equipment. If the contractor’s equipment exceeds the economic life in hours (from appendix D), it is considered overage, and the rates shall be adjusted.

a. The total hourly operating rate for overage equipment (no matter how old) shall be computed on the basis that the equipment is as old as possible "without" exceeding the hours of LIFE as shown in appendix D. Tables 3-1 and 3-2 show factors for the economic life for equipment based on the current pamphlet year (e.g., manufactured in 2008). Select a comparable unit of equipment (horsepower, value, capacity, and size) shown in table 2-1, the total hourly rate can be computed as shown in the following example. If there is no comparable unit of equipment in table 2-1, follow the methodology presented in figure 3-1.

b. The ownership portion of the rate shall be adjusted for equipment that is overage. This adjusted rate is not to exceed the rate for the same unit of equipment that is not overage.

EP 1110-1-8, Vol. 430 Nov 11

3-6

Example: Assume that table 2-1 includes a crane (category C80, subcategory 0.02) manufactured in 2008, has a total hourly rate of $65 per hour, and an ownership rate of $30 per hour. If an equivalent crane owned by a contractor was manufactured in 1994 (maximum life 1999), this crane is overage and the total hourly rate is determined as follows:

Table 2-1 Rate and Adjustment Calculation:

Total hourly rate = $65.00/hr Ownership rate 2008 (DEPR + FCCM) = -($30.00)/hr Ownership rate 1994 adjusted for age (Ownership rate = $30.00) x (0.76) use the oldest age adjustment factor from table 3-1, for category C80, subcategory 0.02, the last year shown.) = +$22.80/hr Total hourly rate for equipment manufactured in 1994 = $57.80/hr

3.13 Standby Rate Adjustment for Equipment of a Different Age than Table 2-1. If the equipment age is other than listed in table 2-1 (purchased new in 2008), adjustment to the hourly standby rate is required. When the age of the equipment is newer or older than the age of the equipment listed in table 2-1, table 3-2 factors may be used to adjust the hourly rate, otherwise the step-by-step calculation method is necessary. The result is a standby rate adjusted for the actual age of the equipment.

a. Standby rates for overage equipment are based on the actual age of the equipment. The age adjustment factor given in table 3-2 is multiplied by the hourly standby cost shown in table 2-1 for the listed or comparable unit of equipment. This results in a standby rate adjusted for the actual age of the unit of equipment being considered.

Hourly Standby Rate Adjusted for Actual Age = Hourly Standby Rate x Age Adjustment Factor

Example: Assume that table 2-1 includes a crane (category C80, subcategory 0.02) manufactured in 2008 and has a standby rate of $20.00 per hour. If an equivalent crane owned by a contractor was manufactured in 2000, the hourly standby rate is determined as follows:

Hourly Standby Rate (table 2-1) = $20.00/hr Age Adjustment Factor (table 3-2) = 0.77 for category C80, subcategory 0.02, and for 2000 (actual year of manufacture)

EP 1110-1-8, Vol. 430 Nov 11

3-7

Adjustment Calculation:

Hourly Standby Rate Adjusted for Actual Age =$20.00/hr (Hourly Standby Rate) x 0.77 (Age Adjustment Factor) =$15.40/hr

b. When the unit of equipment is newer than the equipment listed in table 2-1 (purchased new in 2008), use the adjustment factor in table 3-2 for the year of manufacture. Once the adjustment factor is determined from table 3-2, complete the adjustment calculation as shown in the example above. The step-by-step calculation method shown in figure 3-2 may also be used.

c. When the equipment age is older than the last year shown in table 3-2 or newer than the first year shown in table 3-2, the standby rate must be calculated using the step-by-step methodology shown in figure 3-2.

3.14 Equipment Purchased Used. A detailed methodology for computing a total hourly rate for equipment purchased used is not included in this pamphlet.

a. When actual cost data in accordance with chapter 1 is not available, an hourly rate and standby rate for equipment purchased used can be computed on the basis that the equipment was purchased new by the contractor in the year it was manufactured. Consideration for the actual age of used equipment may require an adjustment for overage.

b. The condition of the used equipment at the time of purchase should consider the extent of capital improvements, mechanical condition, and previous hours of operation. These conditions are difficult or impossible to determine and evaluate when computing a total hourly rate based on actual acquisition cost.

3.15 Rate Calculation Examples. Figure 3-1 illustrates how total hourly rates are adjusted for overage equipment. Figure 3-2 gives a sample calculation for computing adjusted standby rates.

EP 1110-1-8, Vol. 430 Nov 11

3-8

Table 3-1. Equipment Age Adjustment Factors

for

Ownership Costs

The factors in this table are used when the age of a unit of equipment is other than the age of the equipment listed in table 2-1 (purchased new in 2008).

The factors are multiplied by the hourly ownership costs (shown in table 2-1) and result in an ownership rate adjusted for the actual age of the equipment being considered.

When the actual “life” in hours of the unit of equipment has exceeded the economic life given in appendix D, the age will be determined as discussed in chapter 3.

Refer to chapter 3, as follows:

3.11. Equipment of Different Age than Table 2-1

3.12. Rate Adjustment for Overage Equipment

EP 1110-1-8, Vol. 430 Nov 11

Table 3-1 Equipment Age Adjustment Factors for Ownership CostYear Purchased NewLife in Years

CATEGORY

SUB TYPE OF EQUIPMENT 2011 2010 2009 2008 2007 2006 2005 2004 2003 2002 2001 2000 1999 1998 1997 1996 1995 1994

REGION 40 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

EP 1110-1-8

11/30/2011(Vol. 4)

A10 0.00 AGGREGATE / CHIP SPREADERS

A10 0.10 SELF-PROPELLED 1.06 1.04 1.04 1.00 0.96 0.93 0.88

A10 0.20 TOWED & TAILGATE 1.06 1.04 1.04 1.00 0.96

A15 0.00 AIR COMPRESSORS, PORTABLE

A15 0.10 ROTARY SCREW 1.17 1.07 1.06 1.00 0.93 0.89 0.85 0.81

A15 0.20 SHOP TYPE 1.16 1.07 1.06 1.00 0.93 0.89 0.86 0.82 0.82 0.81

A20 0.00 AIR HOSE, TOOLS & EQUIPMENT

A20 0.10 AIR DRILL HOSE 1.14 1.06 1.05 1.00

A20 0.20 SANDBLAST HOSE 1.14 1.06 1.05 1.00

A20 0.30 SANDBLASTERS, BREAKERS, & MISC. AIR TOOLS 1.15 1.07 1.06 1.00 0.94

A25 0.00 ASPHALT PAVING DISTRIBUTORS 1.05 1.04 1.04 1.00 0.96

A30 0.00 ASPHALT PAVERS & MISCELLANEOUS ROAD EQUIPMENT

A30 0.10 SELF PROPELLED 1.05 1.04 1.04 1.00 0.96 0.93 0.89

A30 0.20 TOWED 1.06 1.04 1.04 1.00 0.96 0.93 0.88 0.83

A30 0.30 SLURRY SEAL PAVERS (Cold mix) 1.05 1.04 1.04 1.00 0.96 0.93 0.88 0.83 0.83 0.83

A30 0.40 MISCELLANEOUS ROAD EQUIPMENT 1.06 1.04 1.04 1.00 0.96 0.93 0.88 0.83

A35 0.00 ASPHALT PAVING KETTLES 1.06 1.04 1.04 1.00 0.96

A40 0.00 ASPHALT & CONCRETE MILLERS / PROFILERS / PLANERS / ROTARY GRINDERS

1.06 1.04 1.04 1.00 0.96

A45 0.00 ASPHALT RECYCLERS & SEALERS 1.06 1.04 1.04 1.00

B10 0.00 BATCH PLANTS, ASPHALT & CONCRETE

B10 0.10 ASPHALT 1.06 1.04 1.04 1.00 0.96 0.93 0.88

B10 0.20 CONCRETE 1.06 1.04 1.04 1.00 0.96 0.93 0.88

3- 9

EP 1110-1-8, Vol. 430 Nov 11

3-9


CATEGORY


REGION 40 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

EP 1110-1-8

11/30/2011(Vol. 4)

B10 0.30 PUGMILL 1.06 1.04 1.04 1.00 0.96 0.93 0.88 0.83

B15 0.00 BROOMS, STREET SWEEPERS & FLUSHERS 1.06 1.04 1.03 1.00 0.97 0.94 0.90

B20 0.00 BRUSH CHIPPERS 1.06 1.04 1.03 1.00 0.97 0.94 0.90

B25 0.00 BUCKETS, CLAMSHELL 1.05 1.02 1.03 1.00 0.99 0.98 0.92

B30 0.00 BUCKETS, CONCRETE

B30 0.10 GENERAL PURPOSE, MANUAL TRIP 1.05 1.02 1.03 1.00 0.99 0.98 0.92

B30 0.20 LAYDOWN 1.05 1.02 1.03 1.00 0.99 0.98 0.92

B30 0.30 LOWBOY 1.05 1.02 1.03 1.00 0.99 0.98 0.92

B30 0.40 LOW SLUMP 1.05 1.02 1.03 1.00 0.99 0.98 0.92

B35 0.00 BUCKETS, DRAGLINE

B35 0.10 LIGHT WEIGHT 1.05 1.02 1.03 1.00 0.99 0.98 0.92

B35 0.20 MEDIUM WEIGHT 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.87

B35 0.30 HEAVY WEIGHT 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.87

C05 0.00 CHAIN SAWS 1.06 1.04 1.00

C10 0.00 COMPACTORS, WALK-BEHIND OR REMOTE CONTROLLER

C10 0.10 COMPACTORS, RAMMERS / TAMPERS & VIBRATORY PLATES 1.06 1.03 1.03 1.00

C10 0.20 ROLLERS, VIBRATORY 1.07 1.04 1.04 1.00

C15 0.00 CONCRETE CLEANERS / ABRASIVE BLASTERS

C15 0.10 WALK BEHIND 1.07 1.04 1.04 1.00

C15 0.20 TRUCK/TRAILER MOUNTED 1.07 1.04 1.04 1.00 0.96 0.93 0.89

C20 0.00 CONCRETE BUGGIES 1.07 1.04 1.04 1.00

C25 0.00 CONCRETE FINISHERS/SCREEDS/SPREADERS

3- 10

EP 1110-1-8, Vol. 430 Nov 11

3-10


CATEGORY


REGION 40 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

EP 1110-1-8

11/30/2011(Vol. 4)

C25 0.10 FINISHERS/TROWELS 1.07 1.04 1.04 1.00

C25 0.20 VIBRATORY SCREED 1.07 1.04 1.04 1.00

C25 0.25 VIBRATORY LASER SCREED 1.08 1.05 1.04 1.00 0.96 0.92 0.87

C25 0.30 MATERIAL/TOPPING SPREADERS 1.08 1.05 1.04 1.00 0.96 0.92 0.87

C30 0.00 CONCRETE GRINDERS 1.07 1.04 1.04 1.00

C35 0.00 CONCRETE GUNITERS / SHOTCRETERS 1.07 1.04 1.04 1.00 0.96 0.93

C40 0.00 CONCRETE MIXING UNITS 1.07 1.04 1.04 1.00

C45 0.00 CONCRETE PAVING MACHINES 1.06 1.04 1.04 1.00 0.96

C55 0.00 CONCRETE PUMPS 1.06 1.04 1.03 1.00 0.97 0.94 0.90

C60 0.00 CONCRETE SAWS (Add cost for sawblade wear) 1.06 1.04 1.03 1.00 0.97

C65 0.00 CONCRETE VIBRATORS 1.15 1.07 1.06 1.00

C70 0.00 CRANES, GANTRY & STRADDLE

C75 0.00 CRANES, HYDRAULIC, SELF-PROPELLED 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.86 0.84 0.81 0.75 0.76

C80 0.00 CRANES, HYDRAULIC, TRUCK MOUNTED

C80 0.01 UNDER 26 TON 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.86 0.84 0.81 0.75 0.76

C80 0.02 26 TON THRU 65 TON 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.86 0.84 0.81 0.75 0.76 0.76

C80 0.03 66 TON THRU 125 TON 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.86 0.84 0.81 0.75 0.77 0.76 0.75 0.73

C80 0.04 OVER 125 TON 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.86 0.84 0.81 0.75 0.77 0.76 0.75 0.73 0.72

C85 0.00 CRANES, MECHANICAL, LATTICE BOOM, CRAWLER MOUNTED

C85 0.11 DRAGLINE, CLAMSHELL, 0 THRU 1.0 CY 1.05 1.02 1.03 1.00 0.99 0.97 0.91 0.85 0.83 0.80 0.74 0.75

C85 0.12 DRAGLINE, CLAMSHELL, OVER 1.0 CY THRU 2.5 CY 1.05 1.02 1.03 1.00 0.99 0.97 0.91 0.85 0.83 0.80 0.74 0.75 0.75

C85 0.13 DRAGLINE, CLAMSHELL, OVER 2.5 CY THRU 5.0 CY 1.05 1.02 1.03 1.00 0.99 0.97 0.91 0.85 0.83 0.80 0.74 0.75 0.75 0.74 0.72

3- 11

EP 1110-1-8, Vol. 430 Nov 11

3-11


CATEGORY


REGION 40 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

EP 1110-1-8

11/30/2011(Vol. 4)

C85 0.14 DRAGLINE, CLAMSHELL, OVER 5.0 CY 1.05 1.02 1.03 1.00 0.99 0.97 0.91 0.86 0.83 0.80 0.74 0.76 0.75 0.74 0.72 0.70

C85 0.21 LIFTING, 0 THRU 25 TON 1.05 1.02 1.03 1.00 0.99 0.97 0.91 0.85 0.83 0.80 0.74 0.75 0.75

C85 0.22 LIFTING, 26 TON THRU 50 TON 1.05 1.02 1.03 1.00 0.99 0.97 0.91 0.85 0.83 0.80 0.74 0.75 0.75 0.74 0.72

C85 0.23 LIFTING, 51 TON THRU 150 TON 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.86 0.84 0.81 0.75 0.77 0.76 0.75 0.73 0.72

C85 0.24 LIFTING, OVER 150 TON 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.86 0.84 0.81 0.76 0.77 0.76 0.75 0.73 0.72 0.70 0.68

C90 0.00 CRANES, MECHANICAL, LATTICE BOOM, TRUCK MOUNTED

C90 0.01 UNDER 26 TON 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.86 0.84 0.81 0.75 0.76

C90 0.02 26 TON THRU 65 TON 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.86 0.84 0.81 0.75 0.76 0.76

C90 0.03 66 TON THRU 125 TON 1.05 1.02 1.03 1.00 0.99 0.97 0.91 0.85 0.83 0.80 0.74 0.75 0.75 0.74 0.72

C90 0.04 OVER 125 TON 1.05 1.02 1.03 1.00 0.99 0.97 0.91 0.86 0.83 0.80 0.74 0.76 0.75 0.74 0.72 0.70

C95 0.00 CRANES, TOWER 1.05 1.02 1.03 1.00 0.99 0.97 0.91 0.85 0.83 0.80 0.74 0.75 0.75 0.74 0.72

D10 0.00 DRILLS, AIR/HYDRAULIC,CRWLR MTD,0" THRU 6.5" DIA HOLE (Add cost for drill steel and bit wear)

D10 0.10 DRILLS, AIR TRACK (Add cost for drill steel and bit wear) 1.07 1.04 1.03 1.00 0.93 0.85 0.77 0.70 0.65 0.63 0.56 0.55

D10 0.20 DRILLS, HYDRAULIC TRACK (Add cost for drill steel and bit wear) 1.07 1.04 1.03 1.00 0.92 0.85 0.77 0.70

D15 0.00 DRILLS, HORIZONTAL

D15 0.10 DRILLS, HORIZONTAL BORING & GROUND PIERCING (Add cost for drill steel and bit wear)

1.07 1.04 1.03 1.00 0.92 0.85 0.77 0.70

D15 0.20 DRILLS, HORIZONTAL & DIRECTIONAL (Add cost for drill steel and bit wear) 1.07 1.04 1.03 1.00 0.92 0.85 0.77 0.70

D20 0.00 DRILLS, CORE, COLUMN MOUNTED (Add cost for drill steel and bit wear) 1.07 1.04 1.04 1.00 0.92 0.85 0.77

D25 0.00 DRILLS, CORE & DOWELLING (Add cost for drill steel and bit wear) 1.07 1.04 1.03 1.00 0.92 0.85 0.77 0.70

D30 0.00 DRILLS, EARTH / AUGER (Add cost for drill steel and cutting edge wear) 1.07 1.04 1.03 1.00 0.92 0.85 0.77 0.70

D35 0.00 DRILLS, ROTARY BLASTHOLE (Add cost for drill steel and bit wear)

D35 0.11 DIESEL, 4.5" THRU 9.875" DIAMETER HOLE (Add cost for drill steel and bit wear)

1.07 1.04 1.03 1.00 0.93 0.86 0.79 0.72 0.67 0.65 0.59 0.57

3- 12

EP 1110-1-8, Vol. 430 Nov 11

3-12


CATEGORY


REGION 40 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

EP 1110-1-8

11/30/2011(Vol. 4)

D35 0.12 DIESEL, OVER 9.875" DIAMETER (Add cost for drill steel and bit wear) 1.06 1.04 1.03 1.00 0.93 0.86 0.79 0.72 0.67 0.65 0.59 0.58 0.57 0.55 0.54

D35 0.21 ELECTRIC, 4.5" THRU 9.875" DIAMETER HOLE (Add cost for drill steel and bit wear)

1.07 1.04 1.03 1.00 0.93 0.86 0.79 0.72 0.67 0.65 0.59 0.57

D35 0.22 ELECTRIC, OVER 9.875" DIAMETER (Add cost for drill steel and bit wear) 1.06 1.04 1.03 1.00 0.93 0.86 0.79 0.72 0.67 0.65 0.59 0.58 0.57 0.55 0.54

F10 0.00 FORK LIFTS 1.07 1.04 1.04 1.00 0.96 0.93 0.89 0.82

G10 0.00 GENERATOR SETS

G10 0.10 PORTABLE 1.10 1.05 1.03 1.00 0.95 0.90 0.85

G10 0.20 SKID MOUNTED 1.10 1.05 1.03 1.00 0.95 0.90 0.85 0.81

G15 0.00 GRADERS, MOTOR 1.10 1.09 1.06 1.00 0.96 0.94 0.90 0.85 0.81 0.80 0.79 0.78

H10 0.00 HAMMERS, HYDRAULIC (Demolition tool) (Add cost for point wear) 1.07 1.04 1.04 1.00 0.96

H13 0.00 HAZARDOUS/TOXIC WASTE EQUIPMENT

H13 0.11 COMPACTORS (Compression force) 0 THRU 50 TONS 1.06 1.04 1.04 1.00 0.96 0.94 0.89 0.83

H13 0.12 COMPACTORS (Compression force) OVER 50 TONS 1.07 1.04 1.04 1.00 0.96 0.93 0.89 0.82 0.79 0.77

H13 0.21 FILTER PRESSES, STATIONARY 1.07 1.04 1.04 1.00 0.96 0.93 0.89 0.82

H13 0.22 FILTER PRESSES, MOBILE 1.06 1.04 1.04 1.00 0.96 0.94 0.89 0.83

H13 0.30 CENTRIFUGES 1.07 1.04 1.04 1.00

H13 0.40 SHREDDERS 1.06 1.04 1.04 1.00 0.96 0.94 0.89 0.83

H13 0.51 SOIL TREATMENT PLANT, MOBILE 1.06 1.04 1.04 1.00 0.96 0.94 0.89 0.83

H13 0.61 SLUDGE PROCESSING EQUIP, SLUDGE DISPENSERS 1.06 1.04 1.04 1.00 0.96 0.94 0.89 0.83

H13 0.71 WASTE HANDLING EQUIPMENT, DRUM HANDLING 1.07 1.04 1.04 1.00

H15 0.00 HEATERS, SPACE

H20 0.00 HOISTS & AIR WINCHES 1.07 1.04 1.04 1.00 0.96 0.93 0.89 0.82

H25 0.00 HYDRAULIC EXCAVATORS, CRAWLER MOUNTED

3- 13

EP 1110-1-8, Vol. 430 Nov 11

3-13


CATEGORY


REGION 40 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

EP 1110-1-8

11/30/2011(Vol. 4)

H25 0.10 0 LBS THRU 12,500 LBS (COMPACT EXCAVATORS) 1.06 1.03 1.03 1.00 0.99 0.97 0.90

H25 0.11 OVER 12,500 LBS THRU 40,000 LBS 1.06 1.03 1.03 1.00 0.99 0.97 0.91

H25 0.12 OVER 40,000 LBS THRU 100,000 LBS 1.06 1.03 1.03 1.00 0.99 0.97 0.91 0.84 0.82 0.79

H25 0.13 OVER 100,000 LBS THRU 160,000 LBS 1.06 1.03 1.03 1.00 0.99 0.97 0.91 0.85 0.82 0.79 0.73 0.74 0.74

H25 0.14 OVER 160,000 LBS 1.06 1.02 1.03 1.00 0.99 0.97 0.91 0.85 0.82 0.79 0.73 0.74 0.74 0.73 0.71 0.69

H25 0.21 ATTACHMENTS, MOBILE SHEARS 1.07 1.04 1.04 1.00 0.96

H25 0.22 ATTACHMENTS, MATERIAL HANDLING 1.07 1.04 1.04 1.00 0.96

H25 0.23 ATTACHMENTS, CONCRETE PULVERIZERS 1.07 1.04 1.04 1.00 0.96

H25 0.24 ATTACHMENTS, COMPACTORS 1.07 1.04 1.04 1.00 0.96

H30 0.00 HYDRAULIC EXCAVATORS, WHEEL MOUNTED

H30 0.01 0 THRU 1.0 CY 1.06 1.03 1.03 1.00 0.99 0.97 0.90

H30 0.02 OVER 1.0 CY 1.06 1.03 1.03 1.00 0.99 0.97 0.91 0.84

H35 0.00 HYDRAULIC SHOVELS, CRAWLER MOUNTED

H35 0.11 DIESEL, 0 CY THRU 5.0 CY 1.05 1.02 1.03 1.00 0.99 0.97 0.91 0.85 0.83 0.80 0.74 0.75

H35 0.12 DIESEL, OVER 5.0 CY 1.05 1.02 1.03 1.00 0.99 0.97 0.91 0.85 0.83 0.80 0.74 0.75 0.75

H35 0.21 ELECTRIC, OVER 2.5 CY 1.05 1.02 1.03 1.00 0.99 0.97 0.91 0.85 0.83 0.80 0.74 0.75 0.75 0.74 0.72

L10 0.00 LAND CLEARING EQUIPMENT 1.06 1.03 1.03 1.00 0.96 0.94 0.90 0.85

L15 0.00 LANDSCAPING EQUIPMENT 1.07 1.04 1.04 1.00

L20 0.00 LIGHTING SETS, TRAILER MOUNTED

L20 0.10 METALLIC VAPOR 1.07 1.04 1.04 1.00 0.96 0.93 0.89

L25 0.00 LINE STRIPING EQUIPMENT 1.07 1.04 1.04 1.00 0.96 0.93 0.89

L30 0.00 LOADERS, BELT (Conveyor belts) & ACCESSORIES 1.07 1.04 1.04 1.00 0.96 0.93 0.89 0.82

3- 14

EP 1110-1-8, Vol. 430 Nov 11

3-14


CATEGORY


REGION 40 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

EP 1110-1-8

11/30/2011(Vol. 4)

L35 0.00 LOADERS, FRONT END, CRAWLER TYPE 1.06 1.03 1.03 1.00 0.96 0.94 0.90 0.85

L40 0.00 LOADERS, FRONT END, WHEEL TYPE

L40 0.11 ARTICULATED, 0 THRU 225 HP 1.06 1.03 1.04 1.00 0.96 0.94 0.89 0.84

L40 0.12 ARTICULATED, OVER 225 HP 1.06 1.03 1.03 1.00 0.96 0.94 0.90 0.85 0.82 0.80 0.80

L40 0.20 SKID STEER 1.06 1.03 1.03 1.00 0.96 0.94 0.90

L40 0.21 SKID STEER ATTACHMENTS 1.06 1.03 1.03 1.00

L40 0.31 TOOL CARRIER & TELESCOPIC HANDLERS, 0 THRU 225 HP 1.06 1.03 1.04 1.00 0.96 0.94 0.89 0.84

L40 0.32 TOOL CARRIER & TELESCOPIC HANDLERS, OVER 225 HP 1.06 1.03 1.03 1.00 0.97 0.94 0.90 0.86 0.83 0.81

L45 0.00 LOADERS / BACKHOE, CRAWLER TYPE 1.06 1.03 1.03 1.00 0.96 0.94 0.90

L50 0.00 LOADERS / BACKHOE, WHEEL TYPE 1.06 1.03 1.04 1.00 0.96 0.94 0.89 0.84

L55 0.00 LOADER / BACKHOE, ATTACHMENTS 1.07 1.04 1.04 1.00 0.96

L60 0.00 LOG SKIDDERS 1.06 1.04 1.04 1.00 0.95 0.90 0.85 0.81

M10 0.00 MARINE EQUIPMENT (NON DREDGING)

M10 0.11 AQUATIC MAINTENANCE 1.10 1.08 1.05 1.00 0.96 0.91 0.87 0.84

M10 0.12 AQUATIC MAINTENANCE ATTACHMENTS 1.11 1.08 1.05 1.00 0.96

M10 0.21 HYDRAULIC CUTTERHEAD DREDGE, 8" OR LESS,TRANSPORTABLE 1.09 1.07 1.05 1.00 0.96 0.92 0.88 0.85 0.80 0.76 0.75 0.73 0.72

M10 0.22 HYDRAULIC CUTTERHEAD DREDGE,8" - 12",TRANSPORTABLE 1.09 1.07 1.05 1.00 0.96 0.92 0.88 0.85 0.80 0.76 0.75 0.73 0.72

M10 0.23 HYDRAULIC AUGERHEAD DREDGE,12" OR LESS,TRANSPORTABLE 1.09 1.07 1.05 1.00 0.96 0.92 0.88 0.85 0.80 0.76 0.75 0.73 0.72

M10 0.24 HYDRAULIC FLOATING PUMPS,12" OR LESS,TRANSPORTABLE 1.09 1.07 1.05 1.00 0.96 0.92 0.88

M10 0.25 HYDRAULIC DREDGE PUMPS,12" OR LESS,TRANSPORTABLE 1.10 1.08 1.05 1.00 0.96

M10 0.26 HYDRAULIC DREDGE / PUMP ATTACHMENTS 1.10 1.08 1.05 1.00 0.96

M10 0.31 SMALL MECH DREDGES,CLAMSHELL,BARGE-MTD TO 5 CY 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.86 0.84 0.81 0.75 0.77 0.76 0.75 0.73

3- 15

EP 1110-1-8, Vol. 430 Nov 11

3-15


CATEGORY


REGION 40 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

EP 1110-1-8

11/30/2011(Vol. 4)

M10 0.32 SMALL MECH DREDGES, AMPHIBIOUS EXCAVATORS 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.86

M10 0.33 SMALL MECH DREDGES,HOE-MOUNTED DREDGING ATTACH 1.10 1.07 1.05 1.00 0.96 0.91 0.88 0.84 0.79 0.75 0.74 0.72 0.71 0.70 0.69 0.66

M10 0.41 WORK FLOATS (NON-DREDGING) 1.10 1.07 1.05 1.00 0.96

M10 0.42 WORK BARGES (SECTIONAL, NON-DREDGING) 1.09 1.07 1.04 1.00 0.96 0.92 0.88 0.85 0.80 0.77 0.76 0.74 0.73 0.72 0.71 0.68 0.65 0.64

M10 0.45 FLAT-DECK OR CARGO BARGE (NON-DREDGING) 1.09 1.06 1.04 1.00 0.96 0.92 0.89 0.86 0.82 0.78 0.77 0.75 0.74 0.74 0.72 0.70 0.67 0.66

M10 0.46 DUMP SCOW (NON-DREDGING) 1.09 1.06 1.04 1.00 0.96 0.92 0.89 0.86 0.82 0.78 0.77 0.75 0.74 0.74 0.72 0.70 0.67 0.66

M10 0.47 DRILL BARGE (NON-DREDGING) 1.09 1.07 1.04 1.00 0.96 0.92 0.89 0.86 0.81 0.78 0.76 0.75 0.73 0.73 0.72 0.69 0.66 0.65

M10 0.48 ALL OTHER BARGES (NON-DREDGING) 1.09 1.07 1.04 1.00 0.96 0.92 0.89 0.86 0.81 0.78 0.76 0.75 0.73 0.73 0.72 0.69 0.66 0.65

M10 0.51 BOATS & LAUNCHES, 0 THRU 250 HP 1.10 1.07 1.05 1.00 0.96 0.91 0.88 0.84 0.79 0.75 0.74 0.72 0.71

M10 0.53 BOATS & LAUNCHES, 251 THRU 500 HP 1.09 1.07 1.04 1.00 0.96 0.92 0.88 0.85 0.80 0.76 0.75 0.73 0.72 0.71 0.70

M10 0.54 TUGS, 501 THRU 1,000 HP 1.09 1.07 1.04 1.00 0.96 0.92 0.89 0.85 0.81 0.77 0.76 0.74 0.73 0.72 0.71 0.68 0.65 0.64

M10 0.55 TUGS, 1,000 THRU 2,000 HP 1.09 1.07 1.04 1.00 0.96 0.92 0.89 0.86 0.81 0.77 0.76 0.74 0.73 0.73 0.71 0.69 0.66 0.65

P10 0.00 PILE HAMMER ACCESSORIES - EXTRACTORS & BOX LEADS 1.09 1.05 1.05 1.00 0.95

P20 0.00 PILE HAMMERS, DOUBLE ACTING

P20 0.10 DIESEL 1.07 1.04 1.04 1.00 0.96

P20 0.20 PNEUMATIC (STEAM/AIR) 1.07 1.04 1.04 1.00 0.96

P25 0.00 PILE HAMMERS, SINGLE ACTING

P25 0.10 DIESEL 1.07 1.04 1.04 1.00 0.96

P25 0.20 PNEUMATIC (STEAM/AIR) 1.07 1.04 1.04 1.00 0.96

P30 0.00 PILE HAMMERS, DRIVER/ EXTRACTOR, VIBRATORY 1.07 1.04 1.04 1.00 0.96

P35 0.00 PIPELAYERS 1.06 1.03 1.03 1.00 0.96 0.94 0.90 0.85 0.82 0.80 0.80 0.80

P40 0.00 PLATFORMS & MAN-LIFTS 1.05 1.02 1.03 1.00 0.99 0.98 0.92

3- 16

EP 1110-1-8, Vol. 430 Nov 11

3-16


CATEGORY


REGION 40 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

EP 1110-1-8

11/30/2011(Vol. 4)

P45 0.00 PUMPS, GROUT 1.06 1.04 1.04 1.00 0.96 0.94 0.89

P50 0.00 PUMPS, WATER, CENTRIFUGAL, TRASH

P50 0.11 ENGINE DRIVE 1.07 1.04 1.04 1.00 0.96 0.93 0.89

P50 0.12 ELECTRIC DRIVE 1.07 1.04 1.04 1.00 0.96 0.93 0.89

P50 0.21 WHEEL MOUNTED, ENGINE DRIVE 1.07 1.04 1.04 1.00 0.96 0.93 0.89

P50 0.22 WHEEL MOUNTED, ELECTRIC DRIVE 1.07 1.04 1.04 1.00 0.96 0.93 0.89

P50 0.31 HOSES, PUMP, SUCTION & DISCHARGE 1.06 1.04 1.03 1.00

P55 0.00 PUMPS, WATER, SUBMERSIBLE

P55 0.01 ENGINE DRIVE 1.07 1.04 1.04 1.00 0.96 0.93 0.89

P55 0.02 ELECTRIC DRIVE 1.06 1.04 1.04 1.00 0.96 0.94 0.89

P60 0.00 PUMPS, WATER, CENTRIFUGAL, DEWATERING

P60 0.11 SKID MOUNTED, ENGINE DRIVE 1.07 1.04 1.04 1.00 0.96 0.93 0.89

P60 0.12 SKID MOUNTED, ELECTRIC DRIVE 1.06 1.04 1.04 1.00 0.96 0.94 0.89



P65 0.00 PUMPS, WATER, DIAPHRAGM

P65 0.11 SKID MOUNTED, ENGINE DRIVE 1.07 1.04 1.04 1.00 0.96 0.93 0.89

P65 0.12 SKID MOUNTED, ELECTRIC DRIVE 1.06 1.04 1.04 1.00 0.96 0.94 0.89



P70 0.00 PUMPS, WATER (For core drills)

P70 0.01 ENGINE DRIVE 1.07 1.04 1.04 1.00 0.96 0.93 0.88

3- 17

EP 1110-1-8, Vol. 430 Nov 11

3-17


CATEGORY


REGION 40 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

EP 1110-1-8

11/30/2011(Vol. 4)

P70 0.02 ELECTRIC DRIVE 1.07 1.04 1.04 1.00 0.96 0.93 0.88

R10 0.00 RIPPERS & HYDRAULIC BANK SLOPERS (Add cost for point wear) 1.06 1.03 1.03 1.00 0.96 0.94 0.90

R15 0.00 ROLLERS, STATIC, TOWED, PNEUMATIC 1.07 1.05 1.04 1.00 0.94 0.89 0.84 0.80

R20 0.00 ROLLERS, STATIC, TOWED, STEEL DRUM 1.07 1.05 1.04 1.00 0.94 0.89 0.84 0.80

R30 0.00 ROLLERS, STATIC, SELF-PROPELLED

R30 0.01 PNEUMATIC 1.06 1.04 1.04 1.00 0.95 0.90 0.85

R30 0.02 SMOOTH DRUM 1.06 1.04 1.03 1.00 0.95 0.90 0.85 0.81

R30 0.03 TAMPING FOOT, LANDFILL & SOIL COMPACTORS 1.07 1.04 1.04 1.00 0.94 0.89 0.84 0.80 0.76 0.74

R40 0.00 ROLLERS, VIBRATORY, TOWED 1.07 1.05 1.04 1.00 0.94 0.89 0.84

R45 0.00 ROLLERS, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM 1.07 1.05 1.04 1.00 0.94 0.89 0.84

R50 0.00 ROLLERS, VIBRATORY, SELF-PROPELLED, SINGLE DRUM 1.07 1.05 1.04 1.00 0.94 0.88 0.83

R55 0.00 ROOFING EQUIPMENT 1.07 1.04 1.04 1.00 0.96

S10 0.00 SCRAPERS, ELEVATING

S10 0.01 0 THRU 200 HP 1.10 1.08 1.06 1.00 0.96 0.94 0.90 0.86

S10 0.02 OVER 200 HP 1.11 1.09 1.07 1.00 0.96 0.94 0.90 0.85 0.81 0.80 0.79

S15 0.00 SCRAPERS, CONVENTIONAL 1.10 1.08 1.06 1.00 0.96 0.94 0.90 0.86 0.82 0.81 0.80 0.80

S20 0.00 SCRAPERS, TANDEM POWERED 1.10 1.08 1.06 1.00 0.96 0.94 0.90 0.86 0.82 0.81 0.80 0.80

S25 0.00 SCRAPERS, TRACTOR DRAWN 1.10 1.08 1.06 1.00 0.96 0.94 0.90 0.86 0.82 0.81

S30 0.00 SCREENING & CRUSHING PLANTS

S30 0.10 CONVEYORS 1.06 1.04 1.03 1.00 0.97 0.94 0.90 0.84

S30 0.20 CRUSHERS - VERTICAL & HORIZONTAL SHAFT IMPACTOR 1.06 1.04 1.03 1.00 0.97 0.94 0.90 0.84 0.81 0.80 0.79 0.79 0.78 0.77 0.75 0.73 0.72 0.70

S30 0.21 CRUSHERS - CONE 1.06 1.04 1.03 1.00 0.97 0.94 0.90 0.84 0.81 0.80 0.79 0.79 0.78 0.77 0.75 0.73 0.72 0.70

3- 18

EP 1110-1-8, Vol. 430 Nov 11

3-18


CATEGORY


REGION 40 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

EP 1110-1-8

11/30/2011(Vol. 4)

S30 0.22 CRUSHERS - JAW 1.06 1.04 1.03 1.00 0.97 0.94 0.90 0.84 0.81 0.80 0.79 0.79 0.78 0.77 0.75 0.73 0.72 0.70

S30 0.30 SCREENING PLANT 1.06 1.04 1.03 1.00 0.97 0.94 0.90 0.84

S35 0.00 SNOW REMOVAL EQUIPMENT 1.07 1.04 1.04 1.00 0.96 0.93 0.89

S40 0.00 SOIL & ROAD STABILIZERS 1.10 1.08 1.06 1.00 0.96 0.94 0.90 0.86

S45 0.00 SPLITTERS, ROCK & CONCRETE 1.07 1.04 1.04 1.00 0.96

T10 0.00 TRACTOR BLADES & ATTACHMENTS (including agricultural) 1.06 1.03 1.03 1.00 0.96 0.94 0.90 0.85

T15 0.00 TRACTORS, CRAWLER (DOZER) (includes blade)

T15 0.01 0 THRU 225 HP 1.07 1.03 1.04 1.00 0.96 0.93 0.88 0.83

T15 0.02 226 HP THRU 425 HP 1.06 1.03 1.04 1.00 0.96 0.94 0.89 0.84 0.81 0.79

T15 0.03 OVER 425 HP 1.06 1.03 1.03 1.00 0.96 0.94 0.90 0.85 0.82 0.80 0.80 0.80

T20 0.00 TRACTORS, WHEEL TYPE (DOZER) 1.06 1.04 1.03 1.00 0.95 0.90 0.85 0.81 0.77 0.75 0.74 0.73

T25 0.00 TRACTORS, AGRICULTURAL

T25 0.10 CRAWLER 1.06 1.04 1.04 1.00 0.95 0.90 0.85 0.81

T25 0.20 WHEEL 1.06 1.04 1.04 1.00 0.95 0.90 0.85

T30 0.00 TRENCHERS, CHAIN TYPE CUTTER 1.07 1.05 1.04 1.00 0.94 0.89 0.84

T35 0.00 TRENCHERS, WHEEL TYPE CUTTER 1.07 1.05 1.04 1.00 0.94 0.89 0.84

T40 0.00 TRUCK OPTIONS

T40 0.10 CRANES / HOISTS, PERSONNEL & MATERIAL HANDLING 1.07 1.04 1.04 1.00 0.96 0.93 0.89

T40 0.20 DUMP BODY, REAR 1.06 1.04 1.03 1.00 0.97 0.94 0.90

T40 0.30 FLATBEDS, WITH SIDES 1.07 1.04 1.04 1.00 0.96 0.93 0.89

T40 0.41 HOIST, ELECTRIC DRIVE 1.07 1.04 1.04 1.00 0.96 0.93 0.89

T40 0.50 TRANSIT MIXERS 1.06 1.04 1.04 1.00 0.96 0.94 0.89

3- 19

EP 1110-1-8, Vol. 430 Nov 11

3-19


CATEGORY


REGION 40 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

EP 1110-1-8

11/30/2011(Vol. 4)

T40 0.60 WATER TANKS 1.07 1.04 1.04 1.00 0.96 0.93 0.88

T40 0.70 ALL OTHER OPTIONS 1.07 1.04 1.04 1.00 0.96 0.93 0.89

T45 0.00 TRUCK TRAILERS

T45 0.10 BOTTOM DUMP 1.06 1.04 1.03 1.00 0.97 0.94 0.90 0.84

T45 0.20 END DUMP 1.06 1.04 1.03 1.00 0.97 0.94 0.90 0.84

T45 0.30 PUP TRAILER 1.06 1.04 1.03 1.00 0.97 0.94 0.90

T45 0.41 LOWBOY, RIGID NECK, DROP DECK 1.06 1.04 1.03 1.00 0.97 0.94 0.90 0.84

T45 0.50 FLATBED TRAILER 1.06 1.04 1.03 1.00 0.97 0.94 0.90 0.84

T45 0.60 MISCELLANEOUS / UTILITY 1.06 1.04 1.03 1.00 0.97 0.94 0.90 0.84

T45 0.70 WATER TANKER TRAILER 1.07 1.04 1.04 1.00 0.96 0.93 0.88 0.81

T45 0.80 DECONTAMINATION FACILITY 1.07 1.04 1.04 1.00 0.96 0.93 0.88

T45 0.90 TANK TRAILERS 1.07 1.04 1.04 1.00 0.96 0.93 0.88 0.81

T50 0.00 TRUCKS, HIGHWAY (Add attachments as required)

T50 0.01 0 THRU 10,000 GVW 1.11 1.09 1.06 1.00 0.96 0.93 0.88

T50 0.02 OVER 10,000 THRU 30,000 GVW (Chassis only - Add options) 1.11 1.09 1.06 1.00 0.96 0.93 0.88 0.84

T50 0.03 OVER 30,000 GVW (Chassis only - Add options) 1.11 1.09 1.06 1.00 0.96 0.93 0.88 0.84 0.82 0.80

T55 0.00 TRUCKS, OFF-HIGHWAY

T55 0.10 RIGID FRAME 1.04 1.03 1.02 1.00 0.96 0.94 0.89 0.82 0.77 0.76 0.75 0.73 0.71 0.70 0.69 0.67

T55 0.20 ARTICULATED FRAME 1.04 1.03 1.02 1.00 0.96 0.94 0.89 0.82 0.77 0.76 0.74

T56 0.00 TRUCKS,OFF-HIGHWAY/PRIME MOVER TRACTORS & WAGONS

T56 0.10 PRIME MOVER TRACTORS 1.04 1.03 1.02 1.00 0.96 0.94 0.89 0.82 0.77 0.76 0.75 0.73 0.71 0.70 0.69 0.67

T56 0.20 WAGONS, BOTTOM DUMP 1.04 1.03 1.02 1.00 0.96 0.93 0.88 0.81 0.76 0.74 0.73 0.71

3- 20

EP 1110-1-8, Vol. 430 Nov 11

3-20


CATEGORY


REGION 40 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

EP 1110-1-8

11/30/2011(Vol. 4)

T56 0.30 WAGONS, REAR DUMP 1.04 1.03 1.02 1.00 0.96 0.93 0.88 0.80 0.75 0.74

T57 0.00 TRUCKS, VACUUM 1.07 1.04 1.04 1.00 0.96 0.93 0.89 0.82

T60 0.00 TRUCKS, WATER, OFF-HIGHWAY 1.04 1.03 1.02 1.00 0.96 0.93 0.88 0.80 0.75 0.74

T65 0.00 TUNNEL/MINING EQUIPMENT

T65 0.10 DRIFTING & TUNNELING DRILLS 1.06 1.04 1.03 1.00 0.93 0.86 0.80 0.73 0.68 0.67 0.61 0.59

T65 0.20 TUNNEL BORING MACHINES 1.06 1.04 1.03 1.00 0.96 0.94 0.89 0.83 0.80 0.79 0.78 0.77 0.76 0.75 0.73

T65 0.30 PRODUCTION DRILLING RIGS 1.06 1.04 1.03 1.00 0.93 0.86 0.80 0.73 0.68 0.67

T65 0.40 ROADHEADERS & CONTINUOUS MINERS 1.06 1.04 1.03 1.00 0.96 0.94 0.89 0.83 0.80 0.79 0.78 0.77 0.76

T65 0.50 ROCK BOLTING EQUIPMENT 1.07 1.04 1.04 1.00 0.96 0.93 0.89 0.82

T65 0.61 LOADING & HAULING EQUIPMENT, DIESEL OR GAS 1.07 1.04 1.04 1.00 0.96 0.93 0.89 0.82 0.79 0.77

T65 0.62 LOADING & HAULING EQUIPMENT, ELECTRIC 1.07 1.04 1.04 1.00 0.96 0.93 0.89 0.82 0.79 0.78 0.76 0.76

T65 0.63 LOADING & HAULING EQUIPMENT, AIR-POWERED 1.07 1.04 1.04 1.00 0.96 0.93 0.88 0.81

T65 0.70 LOCOMOTIVES 1.07 1.04 1.04 1.00 0.96 0.93 0.89 0.82 0.79 0.77

T65 0.90 OTHER TUNNELING EQUIPMENT 1.07 1.04 1.04 1.00 0.96 0.93 0.89 0.82

W10 0.00 WAGONS, BOTTOM DUMP 1.04 1.03 1.02 1.00 0.96 0.94 0.89 0.81 0.77 0.75

W15 0.00 WAGONS, REAR DUMP 1.04 1.03 1.02 1.00 0.96 0.94 0.89 0.81 0.77 0.75

W25 0.00 WATER & CO2 BLASTERS

W25 0.10 LOW PRESSURE, (< 5,000 PSI) 1.07 1.04 1.04 1.00

W25 0.20 HIGH PRESSURE, (>= 5,000 PSI) 1.07 1.04 1.04 1.00

W25 0.30 STEAM CLEANERS 1.07 1.04 1.04 1.00

W25 0.40 CO2 BLASTERS 1.07 1.04 1.04 1.00 0.96

W25 0.50 WET ABRASIVE BLASTING SYSTEM (TORBO) 1.08 1.05 1.05 1.00 0.95 0.92 0.86 0.78

3- 21

EP 1110-1-8, Vol. 430 Nov 11

3-21


CATEGORY


REGION 40 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

EP 1110-1-8

11/30/2011(Vol. 4)

W30 0.00 WATER TANKS

W30 0.10 PORTABLE WITH WHEELS 1.04 1.03 1.02 1.00 0.96 0.93 0.88 0.80 0.75 0.74

W30 0.20 SKID MOUNTED 1.04 1.03 1.02 1.00 0.96 0.93 0.88 0.80 0.75 0.74

W35 0.00 WELDERS

W35 0.10 ENGINE DRIVEN 1.07 1.04 1.04 1.00 0.96 0.93 0.88

W35 0.20 ELECTRIC DRIVEN 1.07 1.04 1.04 1.00 0.96

3- 22

EP 1110-1-8, Vol. 430 Nov 11

3-22

1. The unit of equipment is not listed in table 2-1.

2. The equipment is contractor owned.

3. Data for the unit in question:

a. Caterpillar front-end wheel loaderb.c. Serial number indicates year of manufacture = 1999d. 1999 = $205,367

e. Horsepower is 180 hp (fuel is Diesel off-road)f.

= x $3,508 /tire = $14,032g.

4. Table 3-1, Age Adjustment Factors for Ownership Costs:

a. The category L40, subcategory 0.11 (wheel loaders < 225 hp)b. = 2002

5.

a. Economic Indexes from appendix E (wheel loaders EK = 45)(1) = 5612(2) = 5511

b.

(5612 / 5511) x = $209,131 (= 2002 purchase price)

6. Hourly rate is computed as follows in accordance with figure 2-1, Equipment Rate Computation Worksheet.

Assume the following set of given information for the rate calculation example:

For 2002 (first year of economic life), the economic indexFor 1999 (year of manufacture), the economic index

Adjust the actual purchase price:

$205,367

4 tires

(includes all regional discounts, sales tax and freight)

Purchase price [total equipment value (TEV)] indexed to 2002 (first year of economic life): (Purchase price includes discount, sales tax, and freight for this region).

Weight =

TOTAL HOURLY RATE CALCULATION FOR OVERAGE EQUIPMENT

EXAMPLE

The year corresponding to the last age adjustment factor

Drive tire (DT) size = 23.50 x 25, 16 ply, L-3 (appendix F tire code ANNB5)

Actual purchase price in

DT cost (2011)418 cwt

Model 950-G, 4WD, 3.5 CY capacity

Figure 3-1. Total Hourly Rate Calculation for Overage Equipment

EP 1110-1-8, Vol. 430 Nov 11

3-23

1.

a.(1)(2)(3) 2011(4) 2002(5) 180(6) 0(7)

3 D-off

0 None(8) 418 cwt

(9)

Size/Ply App F Code No. Unit Price Cost(a) Front (FT): 0 $0 $0(b) Drive (DT): 23.5X25/16Ply ANNB5 4 $3,508 $14,032(c) 0 $0 $0

(d) $14,032(10)

$0 $209,131

b. 0.11c.

(1) 45(2) A AVERAGE(3) B 0.075(4) 9,250(5) 0.25(6) 0.031(7) 0.000(8) 0.111(9)

(a) 0.83(b) 0.54(c) 0.92

(10) 0.70

USE THIS WORKSHEET TO COMPUTE A HOURLY RATE FOR EQUIPMENT THAT IS NOT IN THIS PAMPHLET OR IS IN THE PAMPHLET BUT NOT EQUIVALENT IN SIZE, CAPACITY, HORSEPOWER OR VALUE. (See Appendix A for a blank

form)Region 04

ID No:


EQUIPMENT INFORMATION AND EXPENSE FACTORS

USE APPENDIX D TO COMPLETE THE FOLLOWING DATA:

Trailing (TT):


Tire Wear Factor:Filter, Oil, and Grease (FOG) Factor (E G D):

Economic Key (EK):

Trailing (TT):


Hourly Expense Calculation Factors:


L40

Tire size and number of tires: (Cost of tires based on present year - see 1.a.(3) and Appendix F)


Drive (DT):

OR actual purchase price:

Total Tire Cost:



Present Year or Year of Use:Year Manufactured:

Equipment Specification Data:Equipment Description: Model and Series:


Fuel

Loader, Front-end, Wheel, 4WD, 3.5 CY capacityCaterpillar Model 950-G


1999 indexed to Horsepower - Equipment:



Front (FT):




Category and Subcategory Number:

Figure 3-1. Total Hourly Rate Calculation for Overage Equipment Page 1 of 6

EP 1110-1-8, Vol. 430 Nov 11

3-24

2.

a. = $0

(1) Discount: (List Price + Accessories) x Discount {1.a.(10)} {1.c.(3)}

($0 + $0.00) x 0.075 = $0

(2) Subtotal = $0

(3) Sales or Import Tax:

Subtotal x Tax Rate

{2.a.(2)} {Appendix B}

$0 x 5.55% = $0

(4) Subtotal = $0

b. Shipping Weight x Freight Rate

per cwt{1.a.(8)}

0,000 cwt x $0.00 /cwt = $0

c. TOTAL[2.]: = $209,131

3.

a. LIFE / Working Hours Per Year (WHPY) = N

{1.c.(4)} {Appendix B}

9,250 hr / 1,260 hr/yr = 7.34 yrs (N)

4.

a.(1)


{1.a.(4)} /

Tire Index, Present Year or

Year of Use, {1.a.(3)} = TCI

Appendix E, EK=100 Appendix E, EK=100

2430 / 3735 = 0.651


[$209,131 x (1.0-0.25) - ( 0.651 x $14,032 )] / 9,250 hr = $15.97 /hr


OWNERSHIP COST

Subtotal {2.a}. - {2.a.(1)}

Tire Cost Index (TCI):

Freight:


Depreciation

(See chapter 3 for used and overage equipment rate adjustments.) {2.a.(4)} + {2.b} OR actual purchase price {1a.(10)}

{Appendix B}

Region 04

EQUIPMENT VALUE


Total Discounted Price: Subtotal: {2.a.(2)} + {2.a.(3)}


EP 1110-1-8, Vol. 430 Nov 11

3-25

4. OWNERSHIP COST (Continued)

b. Facilities Capital Cost of Money (FCCM):

(1) [( N - 1.0 ) x (1.0 + SLV) + 2.0] / (2.0 x N) =Avg Value

Factor{3.a.} {1.c.5.} {3.a.} {AVF}

[(7.34 yr - 1.0) x (1.0 + 0.25) + 2.0] / (2.0 x 7.34 yr) = 0.676




$209,131 x 0.676 x 2.00% / 1,260 hr/yr = $2.24 /hr

c. TOTAL HOURLY OWNERSHIP COST: TOTAL [4.]: = $18.21 /hr

{4.a.(2)} + {4.b.(2)}

5. OPERATING COST

a. Fuel Costs:

(1) Equipment:

Fuel Factor x Horsepower (hp) xFuel Cost per Gallon (gal)

{1.c.(6)} {1.a.(5)} {Appendix B}

0.031 x 180 hp x $3.40 /gal = $18.97 /hr

(2) Carrier:

Fuel Factor x hp x Fuel Cost per gal{1.c.(7)} {1.a.(6)} {Appendix B}

0.000 x 0 hp x $0.00 /gal = $0.00 /hr

(3) Total Hourly Fuel Cost: Total [5.a.] = $18.97 /hr{(5.a (1)} + {5.a (2)}

b. FOG Cost:

(1) Equipment:

FOG Factor xEquipment Hourly

Fuel Cost xLabor Adjustment

Factor (LAF){1.c.(8)} {5.a.(1)} {Appendix B}0.111 x $18.97 /hr x $ 1.04 /hr = $2.19 /hr

Region 04


EP 1110-1-8, Vol. 430 Nov 11

3-26

5.

(2) Carrier:



0.111 x $0.00 /hr x 1.04 = $0.00 /hr

(3) = $2.19 /hr{5.b.(1)} + {5.b.(2)}

c. = $0.00 hr

d.

(1)[EK is from 1c. (1)]

Economic Index, Present Year or Year

of Use,1.a.(3)

/ Economic Index, Year of Manufacture, 1.a.(4)

= EAFAppendix E, EK={1.c.(1)} Appendix E, EK={1.c.(1)}

7025 / 5612 = 1.252


RCF x EAF x LAF= RF

{1.c.(10)} {5.d.(1)} {Appendix B}

0.70 x 1.252 x 1.04 = 0.911

(3) Repair Cost:


[$209,131 - (0.651 x $14,032)] x 0.911 / 9,250

(4) = $19.70 /hr

Region 04

Total [5.b.]Total Hourly FOG Cost:



Repair Cost:

Economic Adjustment Factor (EAF):

Total Hourly Repair Cost: Total [5.d.]

Alternative Fuel/FOG Cost: Total [5.c.](See chapter 2, paragraph 2.24.d. for guidance on when to use.)


EP 1110-1-8, Vol. 430 Nov 11

3-27

5.

e.



(1.5 x $0) / (1.8 x 0.83 x 0 hr) = $0.00 /hr



(1.5 x $14,032) / (1.8 x 0.54 x 3200 hr) = $6.77 /hr



(1.5 x $0) / (1.8 x 0.92 x 0 hr) = $0.00 /hr

(4) Total Tire Wear Cost: Total [5.e.] = $6.77 /hr

f.



$6.77 /hr x (0.15 x 1.04) Total [5.f.] = $1.06 /hr

g. Total [5.] = $48.69 /hrTOTAL HOURLY OPERATING COST:Sum {5.a.} through {5.f.}

Sum {5.e.(1)} through {5.e.(3)}

Region 04


Tire Wear Cost: (Use current price levels. See Appendix F.)

Tire Repair Cost:


EP 1110-1-8, Vol. 430 Nov 11

3-28

6. HOURLY RATES

a. Total Hourly Rate: [based on 40 hours per week (wk)]

Ownership Cost +{4.c.} {5.g.}

$18.21 /hr + $48.69 /hr = $66.90 /hr

b.



{4.a.(2)} {4.b.(2)} {5.g.}

$0.00 /hr + ($0.00 /hr x 40 hr/wk / 60 hr/wk) + $0.00 /hr = $0.00 /hr

c.



($0.00 /hr x 0.50) + $0.00 /hr = $0.00 /hr


See Figure 3-2 for standby calculations for overage equipment



Region 04


example:60 hr/wk

(example:60 hr/wk)

Operating Cost


EP 1110-1-8, Vol. 430 Nov 11

3-29

3-31

Table 3-2. Equipment Age Adjustment Factors

for

Standby costs

The factors in this table are used when the age of a unit of equipment is other than the age of the equipment listed in table 2-1.

These factors are multiplied by the hourly standby costs shown in table 2-1 and result in a standby rate adjusted for the actual age of the equipment being considered.

When the actual “life” in hours of the unit of equipment has exceeded the economic life given in appendix D, the age will be determined as discussed in chapter 3.

Refer to chapter 3, as follows:

3.13. Rate Adjustments Overage Equipment Standby

EP 1110-1-8, Vol. 430 Nov 11

3-30

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

Table 3-2 Equipment Age Adjustment Factors for Standby CostYear Purchased New

CATEGORY


REGION 4 Life in Years

EP 1110-1-8

11/30/2011(Vol. 4)

A10 0.00 AGGREGATE / CHIP SPREADERS

A10 0.10 SELF-PROPELLED 1.05 1.04 1.04 1.00 0.96 0.93 0.88 0.83 0.83 0.83 0.83 0.82 0.80 0.78 0.76 0.73 0.71 0.69

A10 0.20 TOWED & TAILGATE 1.05 1.04 1.04 1.00 0.96 0.93 0.88 0.83 0.83 0.83 0.83 0.82 0.79 0.78 0.75 0.72 0.71 0.68

A15 0.00 AIR COMPRESSORS, PORTABLE

A15 0.10 ROTARY SCREW 1.16 1.07 1.06 1.00 0.93 0.89 0.85 0.82 0.81 0.81 0.81 0.80 0.81 0.81 0.81 0.81 0.80 0.78

A15 0.20 SHOP TYPE 1.15 1.07 1.06 1.00 0.94 0.90 0.86 0.83 0.82 0.82 0.82 0.81 0.82 0.82 0.82 0.82 0.81 0.79

A20 0.00 AIR HOSE, TOOLS & EQUIPMENT

A20 0.10 AIR DRILL HOSE 1.14 1.06 1.05 1.00 0.94 0.90 0.87 0.84 0.84 0.83 0.84 0.82 0.84 0.84 0.83 0.83 0.83 0.81

A20 0.20 SANDBLAST HOSE 1.14 1.06 1.05 1.00 0.94 0.90 0.87 0.84 0.84 0.83 0.84 0.82 0.84 0.84 0.83 0.83 0.83 0.81

A20 0.30 SANDBLASTERS, BREAKERS, & MISC. AIR TOOLS 1.15 1.06 1.06 1.00 0.94 0.90 0.86 0.83 0.83 0.82 0.83 0.81 0.83 0.83 0.83 0.82 0.82 0.80

A25 0.00 ASPHALT PAVING DISTRIBUTORS 1.05 1.04 1.04 1.00 0.96 0.93 0.89 0.84 0.84 0.85 0.85 0.83 0.81 0.80 0.78 0.75 0.73 0.72

A30 0.00 ASPHALT PAVERS & MISCELLANEOUS ROAD EQUIPMENT

A30 0.10 SELF PROPELLED 1.05 1.04 1.04 1.00 0.96 0.93 0.89 0.84 0.84 0.84 0.84 0.83 0.81 0.79 0.77 0.74 0.72 0.70

A30 0.20 TOWED 1.05 1.04 1.04 1.00 0.96 0.93 0.88 0.83 0.83 0.83 0.83 0.82 0.80 0.79 0.76 0.73 0.71 0.69

A30 0.30 SLURRY SEAL PAVERS (Cold mix) 1.05 1.04 1.04 1.00 0.96 0.93 0.88 0.83 0.83 0.84 0.84 0.82 0.80 0.79 0.76 0.73 0.72 0.70

A30 0.40 MISCELLANEOUS ROAD EQUIPMENT 1.05 1.04 1.04 1.00 0.96 0.93 0.88 0.83 0.83 0.83 0.83 0.82 0.80 0.79 0.76 0.73 0.71 0.69

A35 0.00 ASPHALT PAVING KETTLES 1.05 1.04 1.04 1.00 0.96 0.93 0.88 0.83 0.83 0.83 0.83 0.82 0.79 0.78 0.75 0.72 0.71 0.68

A40 0.00 ASPHALT & CONCRETE MILLERS / PROFILERS / PLANERS / ROTARY GRINDERS

1.05 1.04 1.04 1.00 0.96 0.93 0.88 0.83 0.83 0.83 0.83 0.82 0.79 0.78 0.75 0.72 0.71 0.68

A45 0.00 ASPHALT RECYCLERS & SEALERS 1.06 1.04 1.04 1.00 0.96 0.93 0.88 0.83 0.83 0.83 0.83 0.81 0.79 0.78 0.75 0.72 0.70 0.68

B10 0.00 BATCH PLANTS, ASPHALT & CONCRETE

B10 0.10 ASPHALT 1.05 1.04 1.04 1.00 0.96 0.93 0.88 0.83 0.83 0.83 0.83 0.82 0.80 0.78 0.76 0.73 0.71 0.69

B10 0.20 CONCRETE 1.05 1.04 1.04 1.00 0.96 0.93 0.88 0.83 0.83 0.83 0.83 0.82 0.80 0.78 0.76 0.73 0.71 0.69

3- 28

EP 1110-1-8, Vol. 430 Nov 11

3-31

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17


CATEGORY



EP 1110-1-8

11/30/2011(Vol. 4)

B10 0.30 PUGMILL 1.05 1.04 1.04 1.00 0.96 0.93 0.88 0.83 0.83 0.83 0.83 0.82 0.80 0.79 0.76 0.73 0.71 0.69

B15 0.00 BROOMS, STREET SWEEPERS & FLUSHERS 1.06 1.04 1.03 1.00 0.97 0.94 0.90 0.84 0.81 0.80 0.79 0.78 0.77 0.76 0.75 0.73 0.71 0.70

B20 0.00 BRUSH CHIPPERS 1.06 1.04 1.03 1.00 0.97 0.94 0.90 0.84 0.81 0.80 0.79 0.78 0.77 0.76 0.75 0.73 0.71 0.70

B25 0.00 BUCKETS, CLAMSHELL 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.87 0.84 0.82 0.76 0.78 0.79 0.78 0.77 0.76 0.75 0.74

B30 0.00 BUCKETS, CONCRETE

B30 0.10 GENERAL PURPOSE, MANUAL TRIP 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.87 0.85 0.83 0.77 0.79 0.80 0.79 0.78 0.77 0.76 0.75

B30 0.20 LAYDOWN 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.87 0.85 0.83 0.77 0.79 0.80 0.79 0.78 0.77 0.76 0.75

B30 0.30 LOWBOY 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.87 0.85 0.83 0.77 0.79 0.80 0.79 0.78 0.77 0.76 0.75

B30 0.40 LOW SLUMP 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.87 0.85 0.83 0.77 0.79 0.80 0.79 0.78 0.77 0.76 0.75

B35 0.00 BUCKETS, DRAGLINE

B35 0.10 LIGHT WEIGHT 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.87 0.84 0.82 0.76 0.78 0.79 0.78 0.77 0.76 0.75 0.74

B35 0.20 MEDIUM WEIGHT 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.87 0.84 0.82 0.76 0.78 0.79 0.78 0.77 0.76 0.75 0.74

B35 0.30 HEAVY WEIGHT 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.87 0.84 0.82 0.76 0.78 0.79 0.78 0.78 0.76 0.75 0.74

C05 0.00 CHAIN SAWS 1.06 1.04 1.03 1.00 0.97 0.94 0.90 0.84 0.81 0.79 0.78 0.78 0.77 0.76 0.74 0.73 0.71 0.69

C10 0.00 COMPACTORS, WALK-BEHIND OR REMOTE CONTROLLER

C10 0.10 COMPACTORS, RAMMERS / TAMPERS & VIBRATORY PLATES 1.06 1.03 1.03 1.00 0.97 0.94 0.90 0.85 0.82 0.81 0.79 0.79 0.78 0.77 0.76 0.74 0.72 0.71

C10 0.20 ROLLERS, VIBRATORY 1.06 1.04 1.04 1.00 0.96 0.94 0.89 0.83 0.80 0.78 0.77 0.77 0.76 0.75 0.73 0.71 0.69 0.67

C15 0.00 CONCRETE CLEANERS / ABRASIVE BLASTERS

C15 0.10 WALK BEHIND 1.07 1.04 1.04 1.00 0.96 0.93 0.89 0.82 0.78 0.77 0.76 0.75 0.74 0.73 0.71 0.70 0.67 0.65

C15 0.20 TRUCK/TRAILER MOUNTED 1.07 1.04 1.04 1.00 0.96 0.94 0.89 0.83 0.79 0.78 0.76 0.76 0.75 0.74 0.72 0.70 0.68 0.66

C20 0.00 CONCRETE BUGGIES 1.07 1.04 1.04 1.00 0.96 0.93 0.89 0.82 0.78 0.77 0.76 0.75 0.74 0.73 0.71 0.70 0.67 0.65

C25 0.00 CONCRETE FINISHERS/SCREEDS/SPREADERS

3- 29

EP 1110-1-8, Vol. 430 Nov 11

3-32

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17


CATEGORY



EP 1110-1-8

11/30/2011(Vol. 4)

C25 0.10 FINISHERS/TROWELS 1.07 1.04 1.04 1.00 0.96 0.93 0.89 0.82 0.79 0.77 0.76 0.76 0.75 0.73 0.71 0.70 0.68 0.66

C25 0.20 VIBRATORY SCREED 1.07 1.04 1.04 1.00 0.96 0.93 0.89 0.82 0.79 0.77 0.76 0.76 0.75 0.73 0.71 0.70 0.68 0.66

C25 0.25 VIBRATORY LASER SCREED 1.07 1.04 1.04 1.00 0.96 0.93 0.88 0.80 0.77 0.75 0.74 0.73 0.72 0.71 0.69 0.67 0.65 0.63

C25 0.30 MATERIAL/TOPPING SPREADERS 1.07 1.04 1.04 1.00 0.96 0.93 0.88 0.80 0.77 0.75 0.74 0.73 0.72 0.71 0.69 0.67 0.65 0.63

C30 0.00 CONCRETE GRINDERS 1.07 1.04 1.04 1.00 0.96 0.93 0.89 0.82 0.79 0.77 0.76 0.76 0.75 0.73 0.71 0.70 0.68 0.66

C35 0.00 CONCRETE GUNITERS / SHOTCRETERS 1.07 1.04 1.04 1.00 0.96 0.93 0.88 0.81 0.78 0.76 0.75 0.75 0.74 0.72 0.70 0.68 0.66 0.64

C40 0.00 CONCRETE MIXING UNITS 1.07 1.04 1.04 1.00 0.96 0.93 0.89 0.82 0.79 0.77 0.76 0.76 0.75 0.73 0.71 0.70 0.68 0.66

C45 0.00 CONCRETE PAVING MACHINES 1.05 1.04 1.04 1.00 0.96 0.93 0.88 0.83 0.83 0.83 0.83 0.82 0.79 0.78 0.75 0.72 0.71 0.68

C55 0.00 CONCRETE PUMPS 1.06 1.04 1.03 1.00 0.97 0.94 0.90 0.84 0.81 0.80 0.79 0.78 0.77 0.76 0.75 0.73 0.71 0.70

C60 0.00 CONCRETE SAWS (Add cost for sawblade wear) 1.06 1.04 1.03 1.00 0.97 0.94 0.90 0.84 0.81 0.80 0.78 0.78 0.77 0.76 0.74 0.73 0.71 0.69

C65 0.00 CONCRETE VIBRATORS 1.15 1.07 1.06 1.00 0.94 0.90 0.86 0.83 0.83 0.82 0.83 0.81 0.83 0.83 0.82 0.82 0.82 0.80

C70 0.00 CRANES, GANTRY & STRADDLE

C75 0.00 CRANES, HYDRAULIC, SELF-PROPELLED 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.86 0.84 0.82 0.76 0.77 0.77 0.76 0.74 0.72 0.70 0.68

C80 0.00 CRANES, HYDRAULIC, TRUCK MOUNTED

C80 0.01 UNDER 26 TON 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.86 0.84 0.82 0.76 0.77 0.77 0.76 0.74 0.72 0.70 0.68

C80 0.02 26 TON THRU 65 TON 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.86 0.84 0.82 0.76 0.77 0.77 0.76 0.74 0.72 0.70 0.68

C80 0.03 66 TON THRU 125 TON 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.87 0.84 0.82 0.76 0.77 0.77 0.76 0.74 0.72 0.70 0.69

C80 0.04 OVER 125 TON 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.87 0.84 0.82 0.76 0.78 0.77 0.76 0.74 0.73 0.70 0.69

C85 0.00 CRANES, MECHANICAL, LATTICE BOOM, CRAWLER MOUNTED

C85 0.11 DRAGLINE, CLAMSHELL, 0 THRU 1.0 CY 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.86 0.83 0.81 0.75 0.76 0.76 0.75 0.73 0.71 0.69 0.67

C85 0.12 DRAGLINE, CLAMSHELL, OVER 1.0 CY THRU 2.5 CY 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.86 0.84 0.81 0.75 0.76 0.76 0.75 0.73 0.71 0.69 0.67

C85 0.13 DRAGLINE, CLAMSHELL, OVER 2.5 CY THRU 5.0 CY 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.86 0.84 0.81 0.75 0.77 0.76 0.75 0.73 0.72 0.69 0.68

3- 30

EP 1110-1-8, Vol. 430 Nov 11

3-33

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17


CATEGORY



EP 1110-1-8

11/30/2011(Vol. 4)

C85 0.14 DRAGLINE, CLAMSHELL, OVER 5.0 CY 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.86 0.84 0.81 0.76 0.77 0.76 0.75 0.74 0.72 0.70 0.68

C85 0.21 LIFTING, 0 THRU 25 TON 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.86 0.84 0.81 0.75 0.76 0.76 0.75 0.73 0.71 0.69 0.67

C85 0.22 LIFTING, 26 TON THRU 50 TON 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.86 0.84 0.81 0.75 0.77 0.76 0.75 0.73 0.72 0.69 0.68

C85 0.23 LIFTING, 51 TON THRU 150 TON 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.87 0.84 0.82 0.76 0.78 0.77 0.76 0.74 0.73 0.70 0.69

C85 0.24 LIFTING, OVER 150 TON 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.87 0.84 0.82 0.76 0.78 0.77 0.76 0.75 0.73 0.71 0.69

C90 0.00 CRANES, MECHANICAL, LATTICE BOOM, TRUCK MOUNTED

C90 0.01 UNDER 26 TON 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.86 0.84 0.82 0.76 0.77 0.77 0.76 0.74 0.72 0.70 0.68

C90 0.02 26 TON THRU 65 TON 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.86 0.84 0.82 0.76 0.77 0.77 0.76 0.74 0.72 0.70 0.68

C90 0.03 66 TON THRU 125 TON 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.86 0.84 0.81 0.75 0.77 0.76 0.75 0.73 0.72 0.69 0.68

C90 0.04 OVER 125 TON 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.86 0.84 0.81 0.76 0.77 0.76 0.75 0.74 0.72 0.70 0.68

C95 0.00 CRANES, TOWER 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.86 0.84 0.81 0.75 0.77 0.76 0.75 0.73 0.72 0.69 0.68

D10 0.00 DRILLS, AIR/HYDRAULIC,CRWLR MTD,0" THRU 6.5" DIA HOLE (Add cost for drill steel and bit wear)

D10 0.10 DRILLS, AIR TRACK (Add cost for drill steel and bit wear) 1.07 1.04 1.03 1.00 0.93 0.86 0.79 0.72 0.67 0.65 0.59 0.57 0.56 0.55 0.54 0.53 0.50 0.48

D10 0.20 DRILLS, HYDRAULIC TRACK (Add cost for drill steel and bit wear) 1.07 1.04 1.03 1.00 0.93 0.85 0.78 0.71 0.66 0.64 0.58 0.56 0.55 0.53 0.52 0.51 0.48 0.47

D15 0.00 DRILLS, HORIZONTAL

D15 0.10 DRILLS, HORIZONTAL BORING & GROUND PIERCING (Add cost for drill steel and bit wear)

1.07 1.04 1.03 1.00 0.93 0.85 0.78 0.71 0.66 0.64 0.58 0.56 0.55 0.53 0.52 0.51 0.48 0.47

D15 0.20 DRILLS, HORIZONTAL & DIRECTIONAL (Add cost for drill steel and bit wear) 1.07 1.04 1.03 1.00 0.93 0.85 0.78 0.71 0.66 0.64 0.58 0.56 0.55 0.53 0.52 0.51 0.48 0.47

D20 0.00 DRILLS, CORE, COLUMN MOUNTED (Add cost for drill steel and bit wear) 1.07 1.04 1.03 1.00 0.93 0.85 0.78 0.71 0.65 0.63 0.57 0.55 0.54 0.53 0.51 0.50 0.48 0.46

D25 0.00 DRILLS, CORE & DOWELLING (Add cost for drill steel and bit wear) 1.07 1.04 1.03 1.00 0.93 0.85 0.78 0.71 0.66 0.64 0.58 0.56 0.55 0.53 0.52 0.51 0.48 0.47

D30 0.00 DRILLS, EARTH / AUGER (Add cost for drill steel and cutting edge wear) 1.07 1.04 1.03 1.00 0.93 0.85 0.78 0.71 0.66 0.64 0.58 0.56 0.55 0.53 0.52 0.51 0.48 0.47

D35 0.00 DRILLS, ROTARY BLASTHOLE (Add cost for drill steel and bit wear)

D35 0.11 DIESEL, 4.5" THRU 9.875" DIAMETER HOLE (Add cost for drill steel and bit wear)

1.06 1.04 1.03 1.00 0.93 0.86 0.79 0.73 0.68 0.66 0.61 0.59 0.58 0.57 0.56 0.54 0.52 0.50

3- 31

EP 1110-1-8, Vol. 430 Nov 11

3-34

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17


CATEGORY



EP 1110-1-8

11/30/2011(Vol. 4)

D35 0.12 DIESEL, OVER 9.875" DIAMETER (Add cost for drill steel and bit wear) 1.06 1.04 1.03 1.00 0.93 0.87 0.80 0.74 0.69 0.67 0.61 0.60 0.59 0.57 0.56 0.55 0.53 0.51

D35 0.21 ELECTRIC, 4.5" THRU 9.875" DIAMETER HOLE (Add cost for drill steel and bit wear)

1.06 1.04 1.03 1.00 0.93 0.86 0.79 0.73 0.68 0.66 0.61 0.59 0.58 0.57 0.56 0.54 0.52 0.50

D35 0.22 ELECTRIC, OVER 9.875" DIAMETER (Add cost for drill steel and bit wear) 1.06 1.04 1.03 1.00 0.93 0.87 0.80 0.74 0.69 0.67 0.61 0.60 0.59 0.57 0.56 0.55 0.53 0.51

F10 0.00 FORK LIFTS 1.07 1.04 1.04 1.00 0.96 0.94 0.89 0.83 0.79 0.78 0.77 0.76 0.75 0.74 0.72 0.71 0.69 0.67

G10 0.00 GENERATOR SETS

G10 0.10 PORTABLE 1.10 1.05 1.03 1.00 0.95 0.90 0.86 0.81 0.79 0.79 0.79 0.79 0.78 0.78 0.78 0.78 0.77 0.75

G10 0.20 SKID MOUNTED 1.10 1.05 1.03 1.00 0.95 0.90 0.86 0.81 0.79 0.79 0.79 0.79 0.79 0.78 0.78 0.78 0.77 0.75

G15 0.00 GRADERS, MOTOR 1.10 1.08 1.06 1.00 0.96 0.94 0.90 0.86 0.82 0.81 0.80 0.80 0.78 0.75 0.73 0.71 0.67 0.65

H10 0.00 HAMMERS, HYDRAULIC (Demolition tool) (Add cost for point wear) 1.07 1.04 1.04 1.00 0.96 0.93 0.89 0.82 0.79 0.77 0.76 0.76 0.75 0.74 0.72 0.70 0.68 0.66

H13 0.00 HAZARDOUS/TOXIC WASTE EQUIPMENT

H13 0.11 COMPACTORS (Compression force) 0 THRU 50 TONS 1.06 1.04 1.03 1.00 0.96 0.94 0.90 0.84 0.80 0.79 0.78 0.77 0.77 0.75 0.74 0.72 0.70 0.68

H13 0.12 COMPACTORS (Compression force) OVER 50 TONS 1.07 1.04 1.04 1.00 0.96 0.94 0.89 0.83 0.80 0.78 0.77 0.77 0.76 0.74 0.73 0.71 0.69 0.67

H13 0.21 FILTER PRESSES, STATIONARY 1.07 1.04 1.04 1.00 0.96 0.94 0.89 0.83 0.79 0.78 0.77 0.76 0.75 0.74 0.72 0.71 0.69 0.67

H13 0.22 FILTER PRESSES, MOBILE 1.06 1.04 1.03 1.00 0.96 0.94 0.90 0.84 0.80 0.79 0.78 0.77 0.77 0.75 0.74 0.72 0.70 0.68

H13 0.30 CENTRIFUGES 1.07 1.04 1.04 1.00 0.96 0.93 0.89 0.82 0.78 0.77 0.76 0.75 0.74 0.73 0.71 0.70 0.67 0.65

H13 0.40 SHREDDERS 1.06 1.04 1.03 1.00 0.96 0.94 0.90 0.84 0.80 0.79 0.78 0.77 0.77 0.75 0.74 0.72 0.70 0.68

H13 0.51 SOIL TREATMENT PLANT, MOBILE 1.06 1.04 1.03 1.00 0.96 0.94 0.90 0.84 0.80 0.79 0.78 0.77 0.77 0.75 0.74 0.72 0.70 0.68

H13 0.61 SLUDGE PROCESSING EQUIP, SLUDGE DISPENSERS 1.06 1.04 1.03 1.00 0.96 0.94 0.90 0.84 0.80 0.79 0.78 0.77 0.77 0.75 0.74 0.72 0.70 0.68

H13 0.71 WASTE HANDLING EQUIPMENT, DRUM HANDLING 1.06 1.04 1.04 1.00 0.96 0.94 0.89 0.83 0.80 0.78 0.77 0.77 0.76 0.75 0.73 0.71 0.69 0.67

H15 0.00 HEATERS, SPACE

H20 0.00 HOISTS & AIR WINCHES 1.07 1.04 1.04 1.00 0.96 0.94 0.89 0.83 0.79 0.78 0.77 0.76 0.75 0.74 0.72 0.71 0.69 0.67

H25 0.00 HYDRAULIC EXCAVATORS, CRAWLER MOUNTED

3- 32

EP 1110-1-8, Vol. 430 Nov 11

3-35

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17


CATEGORY



EP 1110-1-8

11/30/2011(Vol. 4)

H25 0.10 0 LBS THRU 12,500 LBS (COMPACT EXCAVATORS) 1.06 1.03 1.03 1.00 0.99 0.97 0.91 0.85 0.82 0.79 0.73 0.74 0.74 0.72 0.70 0.68 0.66 0.64

H25 0.11 OVER 12,500 LBS THRU 40,000 LBS 1.06 1.03 1.03 1.00 0.99 0.97 0.91 0.85 0.82 0.79 0.73 0.74 0.74 0.72 0.70 0.68 0.66 0.64



H25 0.14 OVER 160,000 LBS 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.86 0.83 0.81 0.75 0.76 0.76 0.74 0.72 0.71 0.68 0.67

H25 0.21 ATTACHMENTS, MOBILE SHEARS 1.06 1.04 1.04 1.00 0.96 0.94 0.89 0.83 0.80 0.79 0.77 0.77 0.76 0.75 0.73 0.72 0.70 0.68

H25 0.22 ATTACHMENTS, MATERIAL HANDLING 1.07 1.04 1.04 1.00 0.96 0.93 0.89 0.82 0.79 0.77 0.76 0.76 0.75 0.74 0.72 0.70 0.68 0.66

H25 0.23 ATTACHMENTS, CONCRETE PULVERIZERS 1.06 1.04 1.04 1.00 0.96 0.94 0.89 0.83 0.80 0.79 0.77 0.77 0.76 0.75 0.73 0.72 0.70 0.68

H25 0.24 ATTACHMENTS, COMPACTORS 1.06 1.04 1.04 1.00 0.96 0.94 0.89 0.83 0.80 0.79 0.77 0.77 0.76 0.75 0.73 0.72 0.70 0.68

H30 0.00 HYDRAULIC EXCAVATORS, WHEEL MOUNTED

H30 0.01 0 THRU 1.0 CY 1.06 1.03 1.03 1.00 0.99 0.97 0.91 0.85 0.82 0.79 0.73 0.74 0.74 0.72 0.70 0.68 0.66 0.64

H30 0.02 OVER 1.0 CY 1.06 1.02 1.03 1.00 0.99 0.97 0.91 0.85 0.82 0.79 0.73 0.74 0.74 0.73 0.71 0.69 0.66 0.65

H35 0.00 HYDRAULIC SHOVELS, CRAWLER MOUNTED

H35 0.11 DIESEL, 0 CY THRU 5.0 CY 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.86 0.83 0.81 0.75 0.76 0.76 0.75 0.73 0.71 0.69 0.67

H35 0.12 DIESEL, OVER 5.0 CY 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.86 0.84 0.81 0.75 0.76 0.76 0.75 0.73 0.71 0.69 0.67

H35 0.21 ELECTRIC, OVER 2.5 CY 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.86 0.84 0.81 0.75 0.77 0.76 0.75 0.73 0.72 0.69 0.68

L10 0.00 LAND CLEARING EQUIPMENT 1.06 1.03 1.03 1.00 0.96 0.94 0.90 0.85 0.82 0.81 0.80 0.80 0.79 0.76 0.74 0.73 0.70 0.67

L15 0.00 LANDSCAPING EQUIPMENT 1.06 1.04 1.04 1.00 0.96 0.94 0.89 0.83 0.80 0.78 0.77 0.77 0.76 0.75 0.73 0.71 0.69 0.67

L20 0.00 LIGHTING SETS, TRAILER MOUNTED

L20 0.10 METALLIC VAPOR 1.07 1.04 1.04 1.00 0.96 0.94 0.89 0.83 0.79 0.78 0.76 0.76 0.75 0.74 0.72 0.70 0.68 0.66

L25 0.00 LINE STRIPING EQUIPMENT 1.07 1.04 1.04 1.00 0.96 0.94 0.89 0.83 0.79 0.78 0.76 0.76 0.75 0.74 0.72 0.70 0.68 0.66

L30 0.00 LOADERS, BELT (Conveyor belts) & ACCESSORIES 1.07 1.04 1.04 1.00 0.96 0.94 0.89 0.83 0.79 0.78 0.77 0.76 0.75 0.74 0.72 0.71 0.69 0.67

3- 33

EP 1110-1-8, Vol. 430 Nov 11

3-36

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17


CATEGORY



EP 1110-1-8

11/30/2011(Vol. 4)

L35 0.00 LOADERS, FRONT END, CRAWLER TYPE 1.06 1.03 1.03 1.00 0.96 0.94 0.90 0.85 0.82 0.81 0.80 0.80 0.79 0.76 0.74 0.73 0.70 0.67

L40 0.00 LOADERS, FRONT END, WHEEL TYPE

L40 0.11 ARTICULATED, 0 THRU 225 HP 1.06 1.03 1.03 1.00 0.96 0.94 0.90 0.84 0.81 0.80 0.79 0.79 0.78 0.76 0.74 0.73 0.70 0.68

L40 0.12 ARTICULATED, OVER 225 HP 1.06 1.03 1.03 1.00 0.97 0.94 0.90 0.85 0.83 0.81 0.81 0.80 0.79 0.78 0.76 0.75 0.72 0.70

L40 0.20 SKID STEER 1.06 1.03 1.03 1.00 0.96 0.94 0.90 0.85 0.82 0.81 0.80 0.80 0.79 0.77 0.75 0.74 0.71 0.69

L40 0.21 SKID STEER ATTACHMENTS 1.06 1.03 1.03 1.00 0.96 0.94 0.90 0.84 0.82 0.80 0.80 0.79 0.78 0.76 0.74 0.73 0.71 0.68

L40 0.31 TOOL CARRIER & TELESCOPIC HANDLERS, 0 THRU 225 HP 1.06 1.03 1.03 1.00 0.96 0.94 0.90 0.84 0.81 0.80 0.79 0.79 0.78 0.76 0.74 0.73 0.70 0.68

L40 0.32 TOOL CARRIER & TELESCOPIC HANDLERS, OVER 225 HP 1.06 1.03 1.03 1.00 0.97 0.95 0.91 0.86 0.83 0.82 0.81 0.81 0.80 0.78 0.77 0.76 0.73 0.71

L45 0.00 LOADERS / BACKHOE, CRAWLER TYPE 1.06 1.03 1.03 1.00 0.96 0.94 0.90 0.85 0.82 0.81 0.80 0.80 0.79 0.76 0.74 0.73 0.70 0.67

L50 0.00 LOADERS / BACKHOE, WHEEL TYPE 1.06 1.03 1.03 1.00 0.96 0.94 0.90 0.84 0.81 0.80 0.79 0.79 0.78 0.76 0.74 0.73 0.70 0.68

L55 0.00 LOADER / BACKHOE, ATTACHMENTS 1.07 1.04 1.04 1.00 0.96 0.93 0.89 0.82 0.79 0.77 0.76 0.76 0.75 0.74 0.72 0.70 0.68 0.66

L60 0.00 LOG SKIDDERS 1.06 1.04 1.03 1.00 0.95 0.90 0.85 0.82 0.78 0.76 0.75 0.73 0.72 0.69 0.68 0.66 0.66 0.65

M10 0.00 MARINE EQUIPMENT (NON DREDGING)

M10 0.11 AQUATIC MAINTENANCE 1.10 1.07 1.05 1.00 0.96 0.91 0.88 0.84 0.79 0.75 0.74 0.72 0.71 0.70 0.69 0.66 0.63 0.62

M10 0.12 AQUATIC MAINTENANCE ATTACHMENTS 1.10 1.08 1.05 1.00 0.96 0.91 0.87 0.83 0.78 0.73 0.72 0.70 0.69 0.68 0.66 0.63 0.60 0.59

M10 0.21 HYDRAULIC CUTTERHEAD DREDGE, 8" OR LESS,TRANSPORTABLE 1.09 1.07 1.04 1.00 0.96 0.92 0.88 0.85 0.80 0.77 0.76 0.74 0.73 0.72 0.71 0.68 0.65 0.64

M10 0.22 HYDRAULIC CUTTERHEAD DREDGE,8" - 12",TRANSPORTABLE 1.09 1.07 1.04 1.00 0.96 0.92 0.88 0.85 0.80 0.77 0.76 0.74 0.73 0.72 0.71 0.68 0.65 0.64

M10 0.23 HYDRAULIC AUGERHEAD DREDGE,12" OR LESS,TRANSPORTABLE 1.09 1.07 1.04 1.00 0.96 0.92 0.88 0.85 0.80 0.77 0.76 0.74 0.73 0.72 0.71 0.68 0.65 0.64

M10 0.24 HYDRAULIC FLOATING PUMPS,12" OR LESS,TRANSPORTABLE 1.09 1.07 1.05 1.00 0.96 0.92 0.88 0.85 0.80 0.76 0.75 0.73 0.72 0.71 0.70 0.67 0.64 0.63

M10 0.25 HYDRAULIC DREDGE PUMPS,12" OR LESS,TRANSPORTABLE 1.10 1.07 1.05 1.00 0.96 0.91 0.87 0.84 0.79 0.75 0.74 0.72 0.70 0.70 0.68 0.65 0.62 0.61

M10 0.26 HYDRAULIC DREDGE / PUMP ATTACHMENTS 1.10 1.07 1.05 1.00 0.96 0.91 0.87 0.84 0.79 0.75 0.74 0.72 0.70 0.70 0.68 0.65 0.62 0.61

M10 0.31 SMALL MECH DREDGES,CLAMSHELL,BARGE-MTD TO 5 CY 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.87 0.84 0.82 0.76 0.77 0.77 0.76 0.74 0.72 0.70 0.69

3- 34

EP 1110-1-8, Vol. 430 Nov 11

3-37

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17


CATEGORY



EP 1110-1-8

11/30/2011(Vol. 4)

M10 0.32 SMALL MECH DREDGES, AMPHIBIOUS EXCAVATORS 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.86 0.84 0.81 0.75 0.77 0.76 0.75 0.73 0.72 0.69 0.68

M10 0.33 SMALL MECH DREDGES,HOE-MOUNTED DREDGING ATTACH 1.09 1.07 1.05 1.00 0.96 0.92 0.88 0.85 0.80 0.76 0.75 0.73 0.72 0.71 0.70 0.67 0.64 0.63

M10 0.41 WORK FLOATS (NON-DREDGING) 1.09 1.07 1.05 1.00 0.96 0.92 0.88 0.85 0.80 0.76 0.75 0.73 0.72 0.71 0.70 0.67 0.64 0.63

M10 0.42 WORK BARGES (SECTIONAL, NON-DREDGING) 1.09 1.07 1.04 1.00 0.96 0.92 0.89 0.86 0.81 0.77 0.76 0.75 0.73 0.73 0.72 0.69 0.66 0.65

M10 0.45 FLAT-DECK OR CARGO BARGE (NON-DREDGING) 1.08 1.06 1.04 1.00 0.96 0.93 0.89 0.86 0.82 0.78 0.78 0.76 0.75 0.74 0.73 0.71 0.68 0.67

M10 0.46 DUMP SCOW (NON-DREDGING) 1.08 1.06 1.04 1.00 0.96 0.93 0.89 0.86 0.82 0.78 0.78 0.76 0.75 0.74 0.73 0.71 0.68 0.67

M10 0.47 DRILL BARGE (NON-DREDGING) 1.09 1.07 1.04 1.00 0.96 0.92 0.89 0.86 0.81 0.78 0.77 0.75 0.74 0.73 0.72 0.70 0.67 0.66

M10 0.48 ALL OTHER BARGES (NON-DREDGING) 1.09 1.07 1.04 1.00 0.96 0.92 0.89 0.86 0.81 0.78 0.77 0.75 0.74 0.73 0.72 0.70 0.67 0.66

M10 0.51 BOATS & LAUNCHES, 0 THRU 250 HP 1.09 1.07 1.05 1.00 0.96 0.92 0.88 0.85 0.80 0.76 0.75 0.73 0.72 0.71 0.70 0.67 0.64 0.63

M10 0.53 BOATS & LAUNCHES, 251 THRU 500 HP 1.09 1.07 1.04 1.00 0.96 0.92 0.88 0.85 0.80 0.77 0.76 0.74 0.73 0.72 0.71 0.68 0.65 0.64

M10 0.54 TUGS, 501 THRU 1,000 HP 1.09 1.07 1.04 1.00 0.96 0.92 0.89 0.86 0.81 0.78 0.77 0.75 0.74 0.73 0.72 0.69 0.67 0.65

M10 0.55 TUGS, 1,000 THRU 2,000 HP 1.09 1.06 1.04 1.00 0.96 0.92 0.89 0.86 0.82 0.78 0.77 0.75 0.74 0.74 0.72 0.70 0.67 0.66

P10 0.00 PILE HAMMER ACCESSORIES - EXTRACTORS & BOX LEADS 1.08 1.05 1.04 1.00 0.95 0.92 0.86 0.79 0.75 0.73 0.71 0.71 0.70 0.68 0.66 0.64 0.61 0.59

P20 0.00 PILE HAMMERS, DOUBLE ACTING

P20 0.10 DIESEL 1.07 1.04 1.04 1.00 0.96 0.93 0.88 0.81 0.78 0.76 0.75 0.74 0.73 0.72 0.70 0.68 0.66 0.64

P20 0.20 PNEUMATIC (STEAM/AIR) 1.07 1.04 1.04 1.00 0.96 0.93 0.89 0.82 0.79 0.77 0.76 0.76 0.75 0.74 0.72 0.70 0.68 0.66

P25 0.00 PILE HAMMERS, SINGLE ACTING

P25 0.10 DIESEL 1.07 1.04 1.04 1.00 0.96 0.93 0.89 0.82 0.79 0.77 0.76 0.76 0.75 0.74 0.72 0.70 0.68 0.66

P25 0.20 PNEUMATIC (STEAM/AIR) 1.06 1.04 1.04 1.00 0.96 0.94 0.89 0.83 0.80 0.79 0.77 0.77 0.76 0.75 0.73 0.72 0.70 0.68

P30 0.00 PILE HAMMERS, DRIVER/ EXTRACTOR, VIBRATORY 1.07 1.04 1.04 1.00 0.96 0.93 0.89 0.82 0.79 0.77 0.76 0.76 0.75 0.74 0.72 0.70 0.68 0.66

P35 0.00 PIPELAYERS 1.06 1.03 1.03 1.00 0.97 0.94 0.90 0.85 0.83 0.81 0.81 0.80 0.79 0.77 0.75 0.74 0.71 0.68

P40 0.00 PLATFORMS & MAN-LIFTS 1.05 1.02 1.03 1.00 0.99 0.98 0.92 0.87 0.84 0.82 0.76 0.78 0.77 0.76 0.74 0.73 0.71 0.69

3- 35

EP 1110-1-8, Vol. 430 Nov 11

3-38

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17


CATEGORY



EP 1110-1-8

11/30/2011(Vol. 4)

P45 0.00 PUMPS, GROUT 1.06 1.04 1.03 1.00 0.96 0.94 0.89 0.83 0.80 0.79 0.78 0.77 0.76 0.75 0.73 0.72 0.70 0.68

P50 0.00 PUMPS, WATER, CENTRIFUGAL, TRASH

P50 0.11 ENGINE DRIVE 1.07 1.04 1.04 1.00 0.96 0.94 0.89 0.83 0.79 0.78 0.76 0.76 0.75 0.74 0.72 0.70 0.68 0.66

P50 0.12 ELECTRIC DRIVE 1.07 1.04 1.04 1.00 0.96 0.94 0.89 0.83 0.79 0.78 0.76 0.76 0.75 0.74 0.72 0.70 0.68 0.66

P50 0.21 WHEEL MOUNTED, ENGINE DRIVE 1.07 1.04 1.04 1.00 0.96 0.94 0.89 0.83 0.79 0.78 0.76 0.76 0.75 0.74 0.72 0.70 0.68 0.66

P50 0.22 WHEEL MOUNTED, ELECTRIC DRIVE 1.07 1.04 1.04 1.00 0.96 0.94 0.89 0.83 0.79 0.78 0.76 0.76 0.75 0.74 0.72 0.70 0.68 0.66

P50 0.31 HOSES, PUMP, SUCTION & DISCHARGE 1.06 1.04 1.03 1.00 0.97 0.94 0.90 0.84 0.81 0.80 0.78 0.78 0.77 0.76 0.74 0.73 0.71 0.69

P55 0.00 PUMPS, WATER, SUBMERSIBLE

P55 0.01 ENGINE DRIVE 1.07 1.04 1.04 1.00 0.96 0.94 0.89 0.83 0.79 0.78 0.76 0.76 0.75 0.74 0.72 0.70 0.68 0.66

P55 0.02 ELECTRIC DRIVE 1.06 1.04 1.03 1.00 0.96 0.94 0.89 0.83 0.80 0.79 0.78 0.77 0.76 0.75 0.73 0.72 0.70 0.68

P60 0.00 PUMPS, WATER, CENTRIFUGAL, DEWATERING

P60 0.11 SKID MOUNTED, ENGINE DRIVE 1.07 1.04 1.04 1.00 0.96 0.94 0.89 0.83 0.79 0.78 0.76 0.76 0.75 0.74 0.72 0.70 0.68 0.66

P60 0.12 SKID MOUNTED, ELECTRIC DRIVE 1.06 1.04 1.03 1.00 0.96 0.94 0.89 0.83 0.80 0.79 0.78 0.77 0.76 0.75 0.73 0.72 0.70 0.68



P65 0.00 PUMPS, WATER, DIAPHRAGM

P65 0.11 SKID MOUNTED, ENGINE DRIVE 1.07 1.04 1.04 1.00 0.96 0.94 0.89 0.83 0.79 0.78 0.76 0.76 0.75 0.74 0.72 0.70 0.68 0.66

P65 0.12 SKID MOUNTED, ELECTRIC DRIVE 1.06 1.04 1.03 1.00 0.96 0.94 0.89 0.83 0.80 0.79 0.78 0.77 0.76 0.75 0.73 0.72 0.70 0.68



P70 0.00 PUMPS, WATER (For core drills)

P70 0.01 ENGINE DRIVE 1.07 1.04 1.04 1.00 0.96 0.93 0.88 0.82 0.78 0.76 0.75 0.75 0.74 0.72 0.70 0.69 0.67 0.65

3- 36

EP 1110-1-8, Vol. 430 Nov 11

3-39

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17


CATEGORY



EP 1110-1-8

11/30/2011(Vol. 4)

P70 0.02 ELECTRIC DRIVE 1.07 1.04 1.04 1.00 0.96 0.93 0.88 0.82 0.78 0.76 0.75 0.75 0.74 0.72 0.70 0.69 0.67 0.65

R10 0.00 RIPPERS & HYDRAULIC BANK SLOPERS (Add cost for point wear) 1.06 1.03 1.03 1.00 0.96 0.94 0.90 0.85 0.82 0.81 0.80 0.80 0.79 0.76 0.74 0.73 0.70 0.67

R15 0.00 ROLLERS, STATIC, TOWED, PNEUMATIC 1.06 1.04 1.04 1.00 0.94 0.90 0.85 0.81 0.77 0.74 0.73 0.72 0.73 0.71 0.69 0.68 0.67 0.64

R20 0.00 ROLLERS, STATIC, TOWED, STEEL DRUM 1.06 1.04 1.04 1.00 0.94 0.90 0.85 0.81 0.77 0.74 0.73 0.72 0.73 0.71 0.69 0.68 0.67 0.64

R30 0.00 ROLLERS, STATIC, SELF-PROPELLED

R30 0.01 PNEUMATIC 1.06 1.04 1.03 1.00 0.95 0.90 0.85 0.81 0.77 0.75 0.74 0.73 0.74 0.72 0.70 0.70 0.68 0.66

R30 0.02 SMOOTH DRUM 1.06 1.04 1.03 1.00 0.95 0.90 0.85 0.82 0.78 0.76 0.75 0.73 0.74 0.72 0.71 0.70 0.68 0.66

R30 0.03 TAMPING FOOT, LANDFILL & SOIL COMPACTORS 1.06 1.04 1.04 1.00 0.95 0.90 0.85 0.81 0.77 0.75 0.74 0.72 0.73 0.71 0.70 0.69 0.67 0.65

R40 0.00 ROLLERS, VIBRATORY, TOWED 1.07 1.04 1.04 1.00 0.94 0.89 0.85 0.80 0.76 0.74 0.73 0.71 0.73 0.71 0.69 0.68 0.66 0.64

R45 0.00 ROLLERS, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM 1.07 1.04 1.04 1.00 0.94 0.89 0.85 0.80 0.76 0.74 0.73 0.71 0.73 0.71 0.69 0.68 0.66 0.64

R50 0.00 ROLLERS, VIBRATORY, SELF-PROPELLED, SINGLE DRUM 1.07 1.05 1.04 1.00 0.94 0.89 0.84 0.79 0.75 0.73 0.71 0.70 0.71 0.69 0.67 0.66 0.64 0.62

R55 0.00 ROOFING EQUIPMENT 1.06 1.04 1.04 1.00 0.96 0.94 0.89 0.83 0.80 0.79 0.77 0.77 0.76 0.75 0.73 0.72 0.70 0.68

S10 0.00 SCRAPERS, ELEVATING

S10 0.01 0 THRU 200 HP 1.10 1.08 1.06 1.00 0.96 0.94 0.90 0.86 0.83 0.82 0.80 0.80 0.78 0.75 0.73 0.72 0.67 0.65

S10 0.02 OVER 200 HP 1.10 1.08 1.06 1.00 0.96 0.94 0.90 0.86 0.82 0.81 0.80 0.79 0.78 0.75 0.72 0.71 0.66 0.65

S15 0.00 SCRAPERS, CONVENTIONAL 1.09 1.08 1.06 1.00 0.96 0.95 0.91 0.86 0.83 0.82 0.81 0.80 0.79 0.76 0.74 0.73 0.68 0.66

S20 0.00 SCRAPERS, TANDEM POWERED 1.09 1.08 1.06 1.00 0.96 0.95 0.91 0.86 0.83 0.82 0.81 0.80 0.79 0.76 0.74 0.73 0.68 0.66

S25 0.00 SCRAPERS, TRACTOR DRAWN 1.10 1.08 1.06 1.00 0.96 0.95 0.90 0.86 0.83 0.82 0.81 0.80 0.79 0.76 0.73 0.72 0.67 0.66

S30 0.00 SCREENING & CRUSHING PLANTS

S30 0.10 CONVEYORS 1.06 1.04 1.03 1.00 0.97 0.94 0.90 0.84 0.81 0.80 0.79 0.78 0.78 0.76 0.75 0.73 0.71 0.70

S30 0.20 CRUSHERS - VERTICAL & HORIZONTAL SHAFT IMPACTOR 1.06 1.03 1.03 1.00 0.97 0.94 0.90 0.85 0.82 0.81 0.79 0.79 0.78 0.77 0.76 0.74 0.72 0.71

S30 0.21 CRUSHERS - CONE 1.06 1.03 1.03 1.00 0.97 0.94 0.90 0.85 0.82 0.81 0.79 0.79 0.78 0.77 0.76 0.74 0.72 0.71

3- 37

EP 1110-1-8, Vol. 430 Nov 11

3-40

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17


CATEGORY



EP 1110-1-8

11/30/2011(Vol. 4)

S30 0.22 CRUSHERS - JAW 1.06 1.03 1.03 1.00 0.97 0.94 0.90 0.85 0.82 0.81 0.79 0.79 0.78 0.77 0.76 0.74 0.72 0.71

S30 0.30 SCREENING PLANT 1.06 1.04 1.03 1.00 0.97 0.94 0.90 0.84 0.81 0.80 0.79 0.78 0.78 0.76 0.75 0.73 0.71 0.70

S35 0.00 SNOW REMOVAL EQUIPMENT 1.07 1.04 1.04 1.00 0.96 0.94 0.89 0.83 0.79 0.78 0.76 0.76 0.75 0.74 0.72 0.70 0.68 0.66

S40 0.00 SOIL & ROAD STABILIZERS 1.10 1.08 1.06 1.00 0.96 0.94 0.90 0.86 0.83 0.82 0.80 0.80 0.78 0.75 0.73 0.72 0.67 0.65

S45 0.00 SPLITTERS, ROCK & CONCRETE 1.07 1.04 1.04 1.00 0.96 0.93 0.89 0.82 0.79 0.77 0.76 0.76 0.75 0.74 0.72 0.70 0.68 0.66

T10 0.00 TRACTOR BLADES & ATTACHMENTS (including agricultural) 1.06 1.03 1.03 1.00 0.96 0.94 0.90 0.85 0.82 0.81 0.80 0.80 0.79 0.76 0.74 0.73 0.70 0.67

T15 0.00 TRACTORS, CRAWLER (DOZER) (includes blade)

T15 0.01 0 THRU 225 HP 1.06 1.03 1.04 1.00 0.96 0.94 0.89 0.84 0.81 0.79 0.78 0.78 0.77 0.74 0.72 0.70 0.67 0.64

T15 0.02 226 HP THRU 425 HP 1.06 1.03 1.03 1.00 0.96 0.94 0.90 0.85 0.82 0.80 0.80 0.79 0.78 0.75 0.74 0.72 0.69 0.66

T15 0.03 OVER 425 HP 1.06 1.03 1.03 1.00 0.97 0.94 0.90 0.86 0.83 0.81 0.81 0.81 0.79 0.77 0.75 0.74 0.71 0.68

T20 0.00 TRACTORS, WHEEL TYPE (DOZER) 1.06 1.04 1.03 1.00 0.95 0.90 0.86 0.82 0.78 0.76 0.75 0.73 0.72 0.70 0.68 0.67 0.67 0.66

T25 0.00 TRACTORS, AGRICULTURAL

T25 0.10 CRAWLER 1.06 1.04 1.03 1.00 0.95 0.90 0.85 0.82 0.78 0.76 0.75 0.73 0.72 0.69 0.68 0.66 0.66 0.65

T25 0.20 WHEEL 1.06 1.04 1.03 1.00 0.95 0.90 0.85 0.81 0.77 0.75 0.74 0.73 0.71 0.69 0.68 0.66 0.66 0.65

T30 0.00 TRENCHERS, CHAIN TYPE CUTTER 1.07 1.04 1.04 1.00 0.94 0.89 0.85 0.81 0.73 0.74 0.73 0.71 0.70 0.67 0.64 0.63 0.62 0.59

T35 0.00 TRENCHERS, WHEEL TYPE CUTTER 1.07 1.04 1.04 1.00 0.94 0.89 0.85 0.81 0.73 0.74 0.73 0.71 0.70 0.67 0.64 0.63 0.62 0.59

T40 0.00 TRUCK OPTIONS

T40 0.10 CRANES / HOISTS, PERSONNEL & MATERIAL HANDLING 1.07 1.04 1.04 1.00 0.96 0.94 0.89 0.83 0.79 0.78 0.76 0.76 0.75 0.74 0.72 0.70 0.68 0.66

T40 0.20 DUMP BODY, REAR 1.06 1.04 1.03 1.00 0.97 0.94 0.90 0.84 0.81 0.80 0.79 0.78 0.77 0.76 0.75 0.73 0.71 0.70

T40 0.30 FLATBEDS, WITH SIDES 1.07 1.04 1.04 1.00 0.96 0.94 0.89 0.83 0.79 0.78 0.76 0.76 0.75 0.74 0.72 0.70 0.68 0.66

T40 0.41 HOIST, ELECTRIC DRIVE 1.07 1.04 1.04 1.00 0.96 0.94 0.89 0.83 0.79 0.78 0.76 0.76 0.75 0.74 0.72 0.70 0.68 0.66

T40 0.50 TRANSIT MIXERS 1.06 1.04 1.03 1.00 0.96 0.94 0.89 0.83 0.80 0.79 0.78 0.77 0.76 0.75 0.73 0.72 0.70 0.68

3- 38

EP 1110-1-8, Vol. 430 Nov 11

3-41

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17


CATEGORY



EP 1110-1-8

11/30/2011(Vol. 4)

T40 0.60 WATER TANKS 1.07 1.04 1.04 1.00 0.96 0.93 0.88 0.82 0.78 0.76 0.75 0.75 0.74 0.72 0.70 0.69 0.67 0.65

T40 0.70 ALL OTHER OPTIONS 1.07 1.04 1.04 1.00 0.96 0.94 0.89 0.83 0.79 0.78 0.76 0.76 0.75 0.74 0.72 0.70 0.68 0.66

T45 0.00 TRUCK TRAILERS

T45 0.10 BOTTOM DUMP 1.06 1.04 1.03 1.00 0.97 0.94 0.90 0.84 0.81 0.80 0.79 0.78 0.78 0.76 0.75 0.73 0.71 0.70

T45 0.20 END DUMP 1.06 1.04 1.03 1.00 0.97 0.94 0.90 0.84 0.81 0.80 0.79 0.78 0.78 0.76 0.75 0.73 0.71 0.70

T45 0.30 PUP TRAILER 1.06 1.04 1.03 1.00 0.97 0.94 0.90 0.84 0.81 0.80 0.79 0.78 0.77 0.76 0.75 0.73 0.71 0.70

T45 0.41 LOWBOY, RIGID NECK, DROP DECK 1.06 1.04 1.03 1.00 0.97 0.94 0.90 0.84 0.81 0.80 0.79 0.78 0.78 0.76 0.75 0.73 0.71 0.70

T45 0.50 FLATBED TRAILER 1.06 1.04 1.03 1.00 0.97 0.94 0.90 0.84 0.81 0.80 0.79 0.78 0.78 0.76 0.75 0.73 0.71 0.70

T45 0.60 MISCELLANEOUS / UTILITY 1.06 1.04 1.03 1.00 0.97 0.94 0.90 0.84 0.81 0.80 0.79 0.78 0.78 0.76 0.75 0.73 0.71 0.70

T45 0.70 WATER TANKER TRAILER 1.07 1.04 1.04 1.00 0.96 0.93 0.88 0.82 0.78 0.77 0.76 0.75 0.74 0.73 0.71 0.69 0.67 0.65

T45 0.80 DECONTAMINATION FACILITY 1.07 1.04 1.04 1.00 0.96 0.93 0.88 0.82 0.78 0.76 0.75 0.75 0.74 0.72 0.70 0.69 0.67 0.65

T45 0.90 TANK TRAILERS 1.07 1.04 1.04 1.00 0.96 0.93 0.88 0.82 0.78 0.77 0.76 0.75 0.74 0.73 0.71 0.69 0.67 0.65

T50 0.00 TRUCKS, HIGHWAY (Add attachments as required)

T50 0.01 0 THRU 10,000 GVW 1.11 1.09 1.06 1.00 0.96 0.93 0.89 0.84 0.82 0.81 0.79 0.78 0.81 0.79 0.79 0.81 0.80 0.78

T50 0.02 OVER 10,000 THRU 30,000 GVW (Chassis only - Add options) 1.11 1.08 1.06 1.00 0.96 0.93 0.89 0.84 0.82 0.81 0.79 0.79 0.81 0.79 0.79 0.81 0.81 0.78

T50 0.03 OVER 30,000 GVW (Chassis only - Add options) 1.11 1.08 1.06 1.00 0.96 0.93 0.89 0.84 0.82 0.81 0.79 0.79 0.81 0.79 0.80 0.81 0.81 0.78

T55 0.00 TRUCKS, OFF-HIGHWAY

T55 0.10 RIGID FRAME 1.04 1.02 1.02 1.00 0.96 0.94 0.89 0.82 0.78 0.77 0.75 0.74 0.72 0.71 0.70 0.68 0.66 0.62

T55 0.20 ARTICULATED FRAME 1.04 1.03 1.02 1.00 0.96 0.94 0.89 0.82 0.77 0.76 0.75 0.73 0.72 0.71 0.70 0.68 0.65 0.61

T56 0.00 TRUCKS,OFF-HIGHWAY/PRIME MOVER TRACTORS & WAGONS

T56 0.10 PRIME MOVER TRACTORS 1.04 1.02 1.02 1.00 0.96 0.94 0.89 0.82 0.78 0.77 0.75 0.74 0.72 0.71 0.70 0.68 0.66 0.62

T56 0.20 WAGONS, BOTTOM DUMP 1.04 1.03 1.02 1.00 0.96 0.94 0.89 0.82 0.77 0.76 0.74 0.73 0.71 0.70 0.69 0.67 0.64 0.60

3- 39

EP 1110-1-8, Vol. 430 Nov 11

3-42

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17


CATEGORY



EP 1110-1-8

11/30/2011(Vol. 4)

T56 0.30 WAGONS, REAR DUMP 1.04 1.03 1.02 1.00 0.96 0.94 0.88 0.81 0.76 0.75 0.74 0.72 0.70 0.69 0.68 0.66 0.63 0.59

T57 0.00 TRUCKS, VACUUM 1.07 1.04 1.04 1.00 0.96 0.94 0.89 0.83 0.79 0.78 0.77 0.76 0.75 0.74 0.72 0.71 0.69 0.67

T60 0.00 TRUCKS, WATER, OFF-HIGHWAY 1.04 1.03 1.02 1.00 0.96 0.94 0.88 0.81 0.76 0.75 0.74 0.72 0.70 0.69 0.68 0.66 0.63 0.59

T65 0.00 TUNNEL/MINING EQUIPMENT

T65 0.10 DRIFTING & TUNNELING DRILLS 1.06 1.04 1.03 1.00 0.94 0.87 0.80 0.74 0.69 0.68 0.62 0.60 0.59 0.58 0.57 0.56 0.54 0.52

T65 0.20 TUNNEL BORING MACHINES 1.06 1.04 1.03 1.00 0.97 0.94 0.90 0.84 0.81 0.80 0.78 0.78 0.77 0.76 0.74 0.73 0.71 0.69

T65 0.30 PRODUCTION DRILLING RIGS 1.06 1.04 1.03 1.00 0.93 0.87 0.80 0.74 0.69 0.68 0.62 0.60 0.59 0.58 0.57 0.56 0.53 0.52

T65 0.40 ROADHEADERS & CONTINUOUS MINERS 1.06 1.04 1.03 1.00 0.97 0.94 0.90 0.84 0.81 0.79 0.78 0.78 0.77 0.76 0.74 0.73 0.71 0.69

T65 0.50 ROCK BOLTING EQUIPMENT 1.07 1.04 1.04 1.00 0.96 0.94 0.89 0.83 0.79 0.78 0.77 0.76 0.75 0.74 0.72 0.71 0.69 0.67

T65 0.61 LOADING & HAULING EQUIPMENT, DIESEL OR GAS 1.07 1.04 1.04 1.00 0.96 0.94 0.89 0.83 0.80 0.78 0.77 0.77 0.76 0.74 0.73 0.71 0.69 0.67

T65 0.62 LOADING & HAULING EQUIPMENT, ELECTRIC 1.06 1.04 1.04 1.00 0.96 0.94 0.89 0.83 0.80 0.78 0.77 0.77 0.76 0.75 0.73 0.71 0.69 0.68

T65 0.63 LOADING & HAULING EQUIPMENT, AIR-POWERED 1.07 1.04 1.04 1.00 0.96 0.93 0.88 0.82 0.78 0.77 0.76 0.75 0.74 0.73 0.71 0.69 0.67 0.65

T65 0.70 LOCOMOTIVES 1.07 1.04 1.04 1.00 0.96 0.94 0.89 0.83 0.80 0.78 0.77 0.77 0.76 0.74 0.73 0.71 0.69 0.67

T65 0.90 OTHER TUNNELING EQUIPMENT 1.07 1.04 1.04 1.00 0.96 0.94 0.89 0.83 0.79 0.78 0.77 0.76 0.75 0.74 0.72 0.71 0.69 0.67

W10 0.00 WAGONS, BOTTOM DUMP 1.04 1.03 1.02 1.00 0.96 0.94 0.89 0.82 0.77 0.76 0.75 0.73 0.72 0.71 0.70 0.68 0.65 0.61

W15 0.00 WAGONS, REAR DUMP 1.04 1.03 1.02 1.00 0.96 0.94 0.89 0.82 0.77 0.76 0.75 0.73 0.72 0.71 0.70 0.68 0.65 0.61

W25 0.00 WATER & CO2 BLASTERS

W25 0.10 LOW PRESSURE, (< 5,000 PSI) 1.07 1.04 1.04 1.00 0.96 0.93 0.89 0.82 0.78 0.77 0.76 0.75 0.74 0.73 0.71 0.70 0.67 0.65

W25 0.20 HIGH PRESSURE, (>= 5,000 PSI) 1.07 1.04 1.04 1.00 0.96 0.93 0.89 0.82 0.78 0.77 0.76 0.75 0.74 0.73 0.71 0.70 0.67 0.65

W25 0.30 STEAM CLEANERS 1.07 1.04 1.04 1.00 0.96 0.93 0.89 0.82 0.78 0.77 0.76 0.75 0.74 0.73 0.71 0.70 0.67 0.65

W25 0.40 CO2 BLASTERS 1.07 1.04 1.04 1.00 0.96 0.93 0.89 0.82 0.79 0.77 0.76 0.76 0.75 0.74 0.72 0.70 0.68 0.66

W25 0.50 WET ABRASIVE BLASTING SYSTEM (TORBO) 1.08 1.05 1.04 1.00 0.96 0.93 0.87 0.80 0.76 0.74 0.73 0.72 0.71 0.70 0.68 0.66 0.64 0.61

3- 40

EP 1110-1-8, Vol. 430 Nov 11

3-43

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17


CATEGORY



EP 1110-1-8

11/30/2011(Vol. 4)

W30 0.00 WATER TANKS

W30 0.10 PORTABLE WITH WHEELS 1.04 1.03 1.02 1.00 0.96 0.94 0.88 0.81 0.76 0.75 0.74 0.72 0.70 0.69 0.68 0.66 0.63 0.59

W30 0.20 SKID MOUNTED 1.04 1.03 1.02 1.00 0.96 0.94 0.88 0.81 0.76 0.75 0.74 0.72 0.70 0.69 0.68 0.66 0.63 0.59

W35 0.00 WELDERS

W35 0.10 ENGINE DRIVEN 1.07 1.04 1.04 1.00 0.96 0.93 0.88 0.82 0.78 0.76 0.75 0.75 0.74 0.72 0.70 0.69 0.67 0.65

W35 0.20 ELECTRIC DRIVEN 1.07 1.04 1.04 1.00 0.96 0.93 0.89 0.82 0.79 0.77 0.76 0.76 0.75 0.74 0.72 0.70 0.68 0.66

3- 41

EP 1110-1-8, Vol. 430 Nov 11

3-44

1. The unit of equipment is not listed in table 2-1.

2. The equipment is contractor owned.

3.

a.b.c. Serial number indicates year of manufacture = 1999d. 1999 = $205,367

e.f.

= x $3,508/tire = $14,032g.

4.

a. =b. = 1999

5. Hourly rate is computed as follows:

(includes all regional discounts, sales tax and freight)

STANDBY HOURLY RATE CALCULATION FOR OVERAGE EQUIPMENT

EXAMPLE

Actual purchase price in

Assume the following set of given information for the rate calculation example:

Year of manufacture $205,367

4 tires

Purchase price (TEV)

Horsepower is 180 hp (fuel is Diesel off-road)

Weight = 41,800 lbs

Use the actual cost data as follows:

Data for the unit in question:

Caterpillar front-end wheel loaderModel 950-G, 4WD, 3.5 CY capacity

Drive tire (DT) size = 23.50 x 25, 16 ply, L-3 (appendix F tire code ANNB5)DT cost (2009)

Figure 3-2. Total Hourly Rate Calculation for Overage Equipment

EP 1110-1-8, Vol. 430 Nov 11

3-45

1.

a.(1)(2)(3) 2011(4) 1999(5) 180(6) 0(7)

3D-off

0 None(8) 418 cwt

(9)

Size/Ply App F Code No. Unit Price Cost(a) 0 $0 $0(b) 23.5X25/16Ply ANNB5 4 $3,508 $14,032(c) 0 $0 $0(d) $14,032

(10)$0 $205,367

b. 0.11c.

(1) 45(2) A AVERAGE(3) B 0.075(4) 9,250(5) 0.25(6) 0.031(7) 0.000(8) 0.111(9)

(a) 0.83(b) 0.54(c) 0.92

0.70

Equipment Description: Model and Series:Present Year or Year of Use:Year Manufactured:



Horsepower - Equipment:

Loader, Front-end, Wheel, 4WD, 3.5 CY capacityCaterpillar Model 950-G

Fuel





OR actual purchase price:List Price + Accessories: [at Year (yr) of Manufacture]

Hourly Expense Calculation Factors:


L40Category and Subcategory Number:USE APPENDIX D TO COMPLETE THE FOLLOWING DATA:


Front (FT):Drive (DT):Trailing (TT):

(10)

USE THIS WORKSHEET TO COMPUTE A HOURLY RATE FOR EQUIPMENT THAT IS NOT IN THIS PAMPHLET OR IS IN THE PAMPHLET BUT NOT EQUIVALENT IN SIZE, CAPACITY, HORSEPOWER OR VALUE. (See Appendix A for a blank form)

Region 04


Tire Wear Factor:

ID No:

Drive (DT):

Total Tire Cost:

EQUIPMENT INFORMATION AND EXPENSE FACTORS

Equipment Specification Data:

Filter, Oil, and Grease (FOG) Factor (E G D):

Economic Key (EK):

Trailing (TT):



Tire size and number of tires: (Cost of tires based on present year - see 1.a.(3) and Appendix F)

Front (FT):




EP 1110-1-8, Vol. 430 Nov 11

3-46

2.

a. = $0

(1) Discount: (List Price + Accessories) x Discount Code

{1.a.(10)} {1.c.(3)}($0 + $0.00) x 0.075 = $0

(2) Subtotal {2.a.} - {2.a.(1)} Subtotal = $0

(3) Sales or Import Tax: Subtotal x Tax Rate {2.a.(2)} {Appendix B}

$0 x 5.55% = $0

(4) Subtotal = $0

b. x Freight Rate

per cwt{1.a.(8)} {Appendix B}

0,000 cwt x $0.00 /cwt = $0

c. TOTAL[2.]: = $205,367

3.

a. LIFE / = N {1.c.(4)} {Appendix B}

9,250 hr / = 7.34 yrs

4.

a.(1) Tire Cost Index (TCI):


{1.a.(4)} / = TCI Appendix E, EK=100

2371 / = 0.635


[$205,367 x (1.0-0.25) - (0.635 x $14,032 )] / 9,250 /hr = $15.69 /hr

Region 04

EQUIPMENT VALUE


Total Discounted Price: {Subtotal: 2.a.(2) + 2.a.(3)}

Freight: Shipping Weight

1,260 hr/yr


Working Hours Per Year (WHPY)

{2.a.(4)} + {2.b} OR actual purchase price {1a.(10)}

3735

(See chapter 3 for used and overage equipment rate adjustments.)


OWNERSHIP COST

Depreciation

Tire Index, Present Year or Year of Use

{1.a.(3)}Appendix E, EK=100


EP 1110-1-8, Vol. 430 Nov 11

3-47

4.

b.(1) [( N - 1.0) x (1.0 + SLV) + 2.0] / (2.0 x N) = Avg Value

{3.a.} {1.c.5.} {3.a.} (AVF)

[(7.34 yr - 1.0) x (1.0 + 0.25) + 2.0] / (2.0 x 7.34 yr) = 0.676




$205,367 x 0.676 x 2.00% / 1,260 hr/yr = $2.20 /hr

c. TOTAL [4.]: = $17.89 /hr

{4.a.(2)} + {4.b.(2)}

5.

a.

(1)

Fuel Factor x Horsepower (hp) xFuel Cost per Gallon

(gal) {1.c.(6)} {1.a.(5)} {Appendix B}

0.000 x 0 hp x $0.00 /gal = $0.00 /hr

(2)

Fuel Factor x hp x Fuel Cost per gal{1.c.(7)} {1.a.(6)} {Appendix B}

0.000 x 0 hp x $0.00 /gal = $0.00 /hr

(3) Total [5.a.] = $0.00 /hr{5.a (1)} + {5.a (2)}

b.

(1)

FOG Factor xEquipment Hourly Fuel

Cost xLabor Adjustment

Factor (LAF){1.c.(8)} {5.a.(1)} {Appendix B}

0.000 x $0.00 /hr x 0.00 = $0.00 /hr

Fuel Costs:

Region 04

OWNERSHIP COST (Continued)

Facilities Capital Cost of Money (FCCM):

Equipment:

Equipment:

Carrier:

Total Hourly Fuel Cost:

FOG Cost:

TOTAL HOURLY OWNERSHIP COST:

OPERATING COST


EP 1110-1-8, Vol. 430 Nov 11

3-48

5.

(2) Carrier:



0.000 x $0.00 /hr x 0.00 = $0.00 /hr

(3) = $0.00 /hr{5.b.(1)} + {5.b.(2)}

c. = $0.00 hr

d.

(1)

Economic Index, Present Year or

Year of Use,{1.a.(3)}

/ Economic Index, Year of Manufacture,

{1.a.(4)}

Appendix E, EK={1.c.(1)}

Appendix E, EK={1.c.(1)}

0000 / 0000 = 0.000

(2)

RCF x EAF x LAF = RF{1.c.(10)} {5.d.(1)} {Appendix B}

0.00 x 0.000 x 0.00 = 0.000

(3) Repair Cost:


[$0 - (0.000 x $0)] x 0.000 / 0

(4) = $0.00 /hr


Region 04

Total [5.b.]Total Hourly FOG Cost:


Total Hourly Repair Cost: Total [5.d.]

Alternative Fuel/FOG Cost: Total [5.c.]

Economic Adjustment Factor (EAF):EK is from {1.c.(1)}

Repair Factor (RF):

(See chapter 2, paragraph 2.24.d. for guidance on when to use.)

Repair Cost:


EP 1110-1-8, Vol. 430 Nov 11

3-49

5. OPERATING COST (Continued)

e. Tire Wear Cost: (Use current price levels. See Appendix F.)



(1.5 x $0) / (1.8 x 0.00 x 0 hrs) = $0.00/hr

(2)


(1.5 x ($0) / (1.8 x 0.00 x 0 hrs = $0.00/hr

(3)


(1.5 x $0) / (1.8 x 0.00 x 0 hr) = $0.00/hr

(4) Total Tire Wear Cost: Total [5.e.] = $0.00/hrSum {5.e.(1)} through {5.e.(3)}

f.



$0.00/hr x (0.15 x 0.00) Total [5.f.] = $0.00/hr

g. Total [5.] = $0.00/hr

TOTAL HOURLY OPERATING COST:Sum {5.a.} through {5.f.}

Region 04

Drive Tires (DT):

Trailing Tires (TT):

Tire Repair Cost:


EP 1110-1-8, Vol. 430 Nov 11

3-50

6.

a.

Ownership Cost + Operating Cost{4.c.} {5.g.}

$0.00 /hr + $0.00 /hr = $0.00 /hr

See Figure 3-1 for hourly rate calculations for overage equipment

b.


{4.a.(2)} {4.b.(2)} {5.g.}

$0.00 /hr + $0.00 /hr x 40 hr/wk / 60 hr/wk + $0.00 /hr = $0.00 /hr

c.


($15.69 /hr x 0.50) + $2.20 /hr = $10.05 /hr

Region 04

HOURLY RATES

Total Hourly Rate: [based on 40 hours per week (wk)]






example:60 hr/wk

example:60 hr/wk



EP 1110-1-8, Vol. 430 Nov 11

3-51


EP 1110-1-8, Vol. 430 Nov 11

3-52

4-1

CHAPTER 4

Methodology for Dredging Plant and Marine Equipment

SECTION I. GENERAL

4.1 Contents

4.2

. This chapter contains the methodology used to compute ownership and operating rates for dredging plant and permanent floating plant such as floating pile-driving equipment. Dredging plant is marine equipment used for dredging operations for the majority of its life or designed and built for marine/dredging use.

General

a. The ownership and operating rates provided in table 2-1, category M-10, are based on the methodology in chapter 2 for non-dredging equipment. However, the cost data (Acquisition Cost, Horsepower, and Fuel Type) may be used for calculation of dredging plant and marine equipment rates, provided they are calculated in accordance with the methodology provided in this chapter.

.

b. Table 4-1 shows ownership and operating cost factors for various types of dredging plant. When a type of plant is not listed, the cost is estimated by using the factors listed in this table for a similar type of plant.

c. The methodology for determining operating rates for hopper dredges was omitted from this pamphlet due to the limited number of hopper dredges and the complexity of the methods used to calculate the rates. Further information can be found in Engineer Regulation (ER) 1110-2-1302, Engineering and Design, Civil Works Cost Engineering, on the Internet at http://140.194.76.129/publications/eng-regs/er1110-2-1302/toc.htm, and in Engineer Technical Letter (ETL) 1110-2-573 Engineering and Design: Construction Cost Estimating Guide for Civil Works located at http://140.194.76.129/publications/eng-tech-ltrs/etl1110-2-573/toc.htm

d. For mechanical dredges, the cost of the bucket is typically included in the plant value; therefore, no additional allowance should be made for ownership cost. If the bucket cost is not included in the plant value, the bucket may be treated as a separate unit of equipment.

. The methodology for calculating ownership cost is in section V of this chapter.

SECTION II. ANNUAL USE

4.3 Time Available to Dredge

a. The number of months available per calendar year (yr) for dredging shall be based on the work time

.

available to dredge, excluding downtime for major repairs, work in dry dock, bad weather, and environmental restrictions. Figure 4-1 depicts months

EP 1110-1-8, Vol. 430 Nov 11

4-2

available for dredging, including mobilization and demobilization, based on historic data collected by the U.S. Army Corps of Engineers’ regional dredge estimating teams. The data in figure 4-1 shall be used for computing the ownership costs unless specified otherwise in the contract documents.

AVAILABLE TIME TO DREDGE BY REGION (In Months)

Type of Dredging Operation

Region Pipeline Bucket

Atlantic Coast and tributaries

Hopper

9 10 10

Gulf Coast, Lower Mississippi, and Tributaries

10 10 11

Great Lakes, Upper Mississippi, and Tributaries

8 8 8

West Coast and Tributaries 9 9 9

Figure 4-1. Months Available by Region

SECTION III. LIFE

4.4 Life

a. The Useful Life is expressed in years in table 4-1. It is the economic life of the equipment and is used to develop ownership rates for various types of dredging plant.

. The life for determining ownership and operating costs is defined as follows:

b. The Physical Life is expressed in hours (hrs) in table 4-1. It is the life of the unit based on effective working time and is used to develop operating rates for various types of dredging plant.

4.5 Annual Hours Available. The annual hours available to dredge can be established for each type of plant based on the months available and the estimated effective monthly hours worked. Dredging time is defined as effective plus non-effective working time. “Effective working time" is defined as time during the dredging operation when actual production is taking place. "Non-effective working time" is defined as time during the dredging operation when the dredge is operational but no production is taking place. For complete definition of terms see ER 1110-2-1302, Engineering and Design, Civil

EP 1110-1-8, Vol. 430 Nov 11

4-3

Works Cost Engineering. The total annual hours available can be expressed by formula, as follows:

Available Hours per yr = Months Available/yr x Effective Hours/Month

Where: a. Months Available/yr is found in figure 4-1. b. Effective Hours/Month is the effective working time.

SECTION IV. SALVAGE VALUE

4.6 Salvage Value (SLV)

SECTION V. OWNERSHIP COST

. The salvage value, expressed as a decimal, is shown in table 4-1 for different types of plant.

4.7 Ownership Cost

a. The ownership cost is determined from the plant value and is the total expense rate based on depreciation and CMR. When cost or pricing data is available, the actual acquisition price shall be used. Otherwise, the value of a similar piece of plant is used and, if necessary, adjusted so that capacity, size, and horsepower are properly considered.

. Ownership cost is calculated based on a percent of plant value. Plant value is the acquisition cost plus the cost of any initial capital improvements. The value of initial capital improvements is based on those betterments, which were made within 1 year of purchase. Capital improvements do not include any replacement or repair work. Repairs or replacements are an operating cost and are covered in the repair cost allowance. Capital improvements are considered betterments, where the plant has been improved (e.g., adding radar or upgrade of engines). (Note: Only the cost difference between replacement of existing similar engines and actual cost for upgrading engines should be considered as capital improvement). For capital improvements not made within the first year after the initial acquisition, see section VIII.

b. Ownership rate is determined on a yearly basis and distributed over a monthly basis. The monthly rate is calculated based on the available use months by using the following formula:

Months Use AvailablePercent) CMR Yearly Percent DEPR(Yearly x ValuePlant CostOwnershipMonthly +

=

Where: (1) Plant Value = Acquisition price plus initial capital improvements. (2) Yearly DEPR Percent = Ownership percent per year for depreciation. (3) Yearly CMR Percent = Ownership percent per year for cost of money rate.

EP 1110-1-8, Vol. 430 Nov 11

4-4

(4) Available Use Months is from figure 4-1.

4.8 Depreciation Factor

/NSLV) - (1 Percent DEPRYearly =

. Depreciation is computed using the straight-line method. The depreciable value is the acquisition cost, plus initial capital improvements, less estimated salvage. The basis for determining the yearly percentage factor for depreciation is expressed by the following formula:

Where: a. N = Useful Life from table 4-1. b. SLV = Salvage Value from table 4-1.

4.9 The Cost of Money Rate (CMR) Factor

2NCMR) ted2](discounSLV)1)(1-[(NPercentCMRYearly ++

=

. The CMR factor is calculated on a yearly basis and is expressed here as an annual percentage factor. The CMR used in the calculation is the rate in effect at the time the work was performed. This formula is expressed as follows:

Where: a. N = Useful Life from table 4-1. b. SLV = Salvage Value from table 4-1. c. Discounted CMR = Cost of money rate (appendix I) reduced by 25 percent for

overhead and profit allowance.

4.10 Other Ownership Elements

SECTION VI. OPERATING FACTORS

. Taxes, storage (lay up), and insurance are considered indirect (overhead) costs as defined in ER 1110-2-1302, appendix D. These costs are not included in ownership rates since they vary by geographic area and with individual contractors. These costs are considered as overhead costs and are, therefore, not included here so they will not be duplicated in the overhead in the estimate or submitted proposal.

4.11 Hourly Operating Cost

4.12

. Operating cost is based on effective working time. Dredging plant operating factors are shown in table 4-1. These factors, which are described in paragraph 4.12, are not intended to replace historical data but shall be used when historical data is limited or nonexistent.

Prime and Secondary Power. Prime power refers to the primary operating engine for the dredge or other piece of attendant plant. Secondary power refers to all other secondary engines or power plants. If more than one secondary power engine is

EP 1110-1-8, Vol. 430 Nov 11

4-5

present, the horsepower is totaled. Fuel consumption factors are prepared on the same basis as in chapter 2. Hourly fuel costs are calculated separately for the primary and secondary engines. The formula used is expressed as follows:

Hourly Fuel Cost = Horsepower x Fuel Cost/Gallon x Engine Fuel Factor

Where: a. Horsepower is the engines rated horsepower. b. Fuel Cost/Gallon is based on values shown in appendix B. See chapter 3 for

fuel cost adjustments. c. Fuel Factor - Gas or Diesel Fuel. The fuel factor is listed in table 4-1 for the

primary and secondary engines.

4.13 Water, Lube, and Supplies (WLS). This factor is similar to the filters, oil, and grease (FOG) factor described in chapter 2. This item is computed as either a percentage of the hourly fuel costs or, if the type of plant has no engine, a reasonable hourly cost should be included. This factor does not include

Water, Lube, and Supply Cost = WLS factor x Hourly Fuel Cost

an allowance for the oiler normally assigned to the dredge or other piece of dredging plant. The formula is expressed as follows:

Where: a. WLS Factor is obtained from table 4-1. b. Hourly Fuel cost is calculated as shown in paragraph 4-12.

4.14 Repairs (RPR)

hr in LifeLAF) x EAF x PRP x Value Plant (TotalCost Repair =

. This factor includes an allowance for all major and minor repairs and is similar to the maintenance and repair cost factor (RCF) described in chapter 2. The economic adjustment factor (EAF) and the labor adjustment factor (LAF) are required to develop this cost. The formula is expressed as follows:

Where: a. Total Plant Value = Acquisition price plus Initial capital improvements. b. RPR = Repair Factor from table 4-1. c. EAF = Economic Index (present year)/ Economic Index (acquisition year). d. LAF = Labor Adjustment Factor from appendix B. e. Life in hrs = Physical Life from table 4-1. It should be noted that the repair allowance does not include the following

estimated additive items:

EP 1110-1-8, Vol. 430 Nov 11

4-6

f. Excessive dredge wear for parts (e.g., cutter teeth and main suction pumps) is not included due to the wide variety of materials being dredged. The original cost of the bucket and normal wear are typically included in the plant value covered in the plant rate. Excessive bucket wear for mechanical dredges is estimated as an additive item or treated as a separate unit of equipment from table 2-1. Allowances for wear due to abrasive material should only be included as an additive item if it is warranted and is not considered elsewhere in the estimate.

g. Dry docking costs, which represent an allowance for rental of the dry dock facility, are not included because they vary greatly depending on the facilities available. Repairs incurred while in dry dock, which occur periodically, are in the repairs. Dry docking costs will be allocated on an average annual basis over the years between such occurrences in accordance with Cost Accounting Standards and Generally Accepted Accounting Practices.

h. There is no predetermined allowance in the dredging plant methodology for jobsite yard costs, mobilization, or demobilization. All of these cost elements must be separately estimated to match each project’s construction conditions.

SECTION VII. STANDBY

4.15 Standby Rate

a. Standby is a directed delay by the Government and will not be allowed during periods when the plant would have otherwise been in idle status, such as non-effective working time. Since ownership is calculated based on life in years computed monthly, standby should be paid only when additional time has been directed by the Government. Standby is to be paid on a 24-hour basis.

. The standby rate is computed by allowing the full ownership cost. In addition to the standby ownership rate, it may be necessary on dredges to include operating costs. Examples of allowable operating cost are as follows: a generator fuel allowance to account for operation of a diesel engine generator for power to operate pumps; navigation lights; minimum crew; etc.

b. Standby for pipeline and accessories shall be based on pumping mud in determining values from table 4-1.

SECTION VIII. NEGOTIATED PROCUREMENT

4.16 Rates

4.17

. The calculated dredging plant rates based on the methodology presented in this chapter should be used for preparing a reasonable contract estimate. When adequate cost or pricing data is available and submitted by the contractor for negotiated procurement, the rates may be adjusted in accordance with the methodology in this chapter. Cost or pricing data is defined in FAR 15.4, Contract Pricing.

Allowance for Additional Capital Improvements. Allowance for additional capital improvements shall be calculated in accordance with accepted general accounting

EP 1110-1-8, Vol. 430 Nov 11

4-7

principles. When adequate cost or pricing data is not available, factors for a similar unit of equipment may be used for determining the ownership rate for overage equipment and plant.

4.18 Overage Plant

a. When actual cost or pricing data is available to adjust the operating rate, the data must be accurate, complete, and established in accordance with accepted general accounting principles.

. When the plant has exceeded the useful life given in table 4-1, it is considered overage. The ownership rate for overage plant should be determined with the same methodology described in section V.

b. When actual cost or pricing data is not available, the total hourly operating rate for overage equipment shall be computed on the basis that the equipment is equal to the useful life as shown in table 4-1.

4.19 Dredging Plant Purchased Used

SECTION IX. RATE CALCULATION EXAMPLE

. For plant purchased used, the ownership and operating rate must be calculated on an individual case, due to the varying conditions. When actual cost or pricing data is not available, the methodology from this chapter shall be used and values for life and salvage from table 4-1 can be adjusted. Support for adjustments can be obtained by calling the Chief, Cost Engineering Branch, Engineering and Construction Division, Walla Walla District, U.S. Army Corps of Engineers (CENWW-EC-X), telephone 509-527-7511 or 509-527-7510.

4.20 Rate Calculation Example

. The example shown in figure 4-2 illustrates the use of figure 4-1, table 4-1, and the regional data from appendix B to generate a rate. For illustration purposes, assume that a 24-inch hydraulic dredge (pipeline) was purchased new in 1993 for $4,200,000, including tax and delivery, and there were no initial capital improvements. This example uses 500 hours per month and a discounted CMR of 2.00 percent.

EP 1110-1-8, Vol. 430 Nov 11

4-8

Table 4-1. Dredging Plant Cost Factors

Type of Plant Useful

Life Physical

Life Salvage Value

Prime Engine Fuel Factor

Secondary Engine Fuel Factor

WLS %

RPR %

YRS HR SLV HPF G D HPF G D G D Hydraulic Dredges - Pipeline

(Cutterhead or Dustpan) (Based on Discharge Diameter) (Non-Truckable)

8 inch and under 5 10,000 0.05 80 0.083 0.045 70 0.072 0.039 20 22 70 9 inch through 10 inch 6 12,000 0.05 80 0.083 0.045 70 0.072 0.039 20 22 80 11 inch through 12 inch 8 16,000 0.05 80 0.083 0.045 70 0.072 0.039 20 22 90 13 inch through 15 inch 15 40,000 0.05 80 0.083 0.045 70 0.072 0.039 20 22 100 16 inch through 17 inch 20 80,000 0.05 80 0.083 0.045 70 0.072 0.039 20 22 110 18 inch through 20 inch 20 100,000 0.05 80 0.083 0.045 70 0.072 0.039 20 22 120 21 inch through 22 inch 25 120,000 0.10 80 0.083 0.045 70 0.072 0.039 20 22 130 23 inch through 24 inch 25 130,000 0.10 80 0.083 0.045 70 0.072 0.039 20 22 130 25 inch through 29 inch 30 135,000 0.10 80 0.083 0.045 70 0.072 0.039 20 22 130 30 inch or larger 30 135,000 0.10 80 0.083 0.045 70 0.072 0.039 20 22 130

Barge Mounted Booster Pump (For Pipeline Dredges) 16 inch through 17 inch 20 80,000 0.05 80 0.083 0.045 70 0.072 0.039 22 24 80 18 inch through 20 inch 20 100,000 0.10 80 0.083 0.045 70 0.072 0.039 22 24 90 21 inch through 22 inch 25 120,000 0.10 80 0.083 0.045 70 0.072 0.039 22 24 100 23 inch through 24 inch 25 130,000 0.10 80 0.083 0.045 70 0.072 0.039 22 24 110 25 inch through 29 inch 30 135,000 0.10 80 0.083 0.045 70 0.072 0.039 22 24 120 30 inch or larger 30 135,000 0.10 80 0.083 0.045 70 0.072 0.039 22 24 120

SLV = Salvage Value HPF = Horsepower Factor G = Gas D = Diesel WLS = Water, Lube and Supplies RPR = Repairs

EP 1110-1-8, Vol. 430 Nov 11

4-9

Table 4-1. Dredging Plant Cost Factors (Continued)


Life Physical

Life Salvage Value



WLS %

RPR %

YRS HR SLV HPF G D HPF G D G D Mechanical Dredges (Large) 1

Clamshell - under 5 cy 8 18,000 0.05 70 0.072 0.039 60 0.062 0.033 22 24 90 Clamshell - 6 cy to 10 cy 13 26,000 0.05 70 0.072 0.039 60 0.062 0.033 22 24 100 Clamshell - 11 cy to 15 cy 20 40,000 0.05 70 0.072 0.039 60 0.062 0.033 22 24 110 Clamshell - 16 cy to 20 cy 25 75,000 0.05 70 0.072 0.039 60 0.062 0.033 22 24 120 Clamshell - 20 cy and over 30 90,000 0.05 70 0.072 0.039 60 0.062 0.033 22 24 130 All Other Types

(Bucket or Dipper) 25 90,000 0.10 70 0.072 0.039 60 0.062 0.033 22 24 120

Barge Mounted Crane with Clamshell Bucket Non - Dredging

Clamshell - under 6 cy 9 18,000 0.05 55 0.055 0.031 45 0.045 0.025 22 24 85 Clamshell - 6 cy to 10 cy 14 28,000 0.05 55 0.055 0.031 45 0.045 0.025 22 24 95 Clamshell - 11 cy to 15 cy 21 42,000 0.05 55 0.055 0.031 45 0.045 0.025 22 24 105

Barge Mounted Lifting Crane 25 Ton to 75 Ton, 45’ Boom 9 18,000 0.05 40 0.040 0.022 30 0.030 0.017 22 24 80 75 Ton to 125 Ton, 60’ Boom 14 28,000 0.05 40 0.040 0.022 30 0.030 0.017 22 24 90 Over 125 Ton, over 60’ Boom 21 42,000 0.05 40 0.040 0.022 30 0.030 0.017 22 24 100

Barges (Used with Dredging) Fuel or Water 20 90,000 0.05 20 0.021 0.011 20 0.021 0.011 18 20 60 Equipment or Work 20 90,000 0.05 20 0.021 0.011 20 0.021 0.011 18 20 60 Derrick 20 90,000 0.10 20 0.021 0.011 20 0.021 0.011 18 20 70 Anchor 20 90,000 0.05 20 0.021 0.011 20 0.021 0.011 18 20 60 Mooring Barge 20 90,000 0.05 20 0.021 0.011 20 0.021 0.011 18 20 60 Dump Scow 20 90,000 0.05 20 0.021 0.011 20 0.021 0.011 18 20 70

SLV = Salvage Value HPF = Horsepower Factor G = Gas D = Diesel WLS = Water, Lube and Supplies RPR = Repairs 1 Sized by the largest bucket used (normally a mud bucket)

EP 1110-1-8, Vol. 430 Nov 11

4-10



Life Physical

Life Salvage Value



WLS %

RPR %

YRS HR SLV HPF G D HPF G D G D Boats – See Category M10

Tugs and Tenders (Used with Dredging) Under 500 hp 8 18,000 0.10 80 0.083 0.045 70 0.072 0.039 32 38 80 501 through 1,000 hp 10 40,000 0.10 80 0.083 0.045 70 0.072 0.039 32 38 90 1,001 through 2,000 hp 15 55,000 0.10 80 0.083 0.045 70 0.072 0.039 32 38 100 2,001 through 3,000 hp 20 100,000 0.10 80 0.083 0.045 70 0.072 0.039 32 38 110 Over 3,000 hp 25 120,000 0.10 80 0.083 0.045 70 0.072 0.039 32 38 120

Pipeline and Accessories (Inland Environment)

Metal Pipeline (under 20 inch) Pumping Mud 2 9,000 0.10 0 0.000 0.000 0 0.000 0.000 0 0 5 Pumping Sand 1 4,500 0.10 0 0.000 0.000 0 0.000 0.000 0 0 5 Pumping Rock (Gravel) 0.3 1,500 0.10 0 0.000 0.000 0 0.000 0.000 0 0 5 Joints 3 12,000 0.10 0 0.000 0.000 0 0.000 0.000 0 0 30 Pontoons/Floats 12 60,000 0.10 0 0.000 0.000 0 0.000 0.000 0 0 5

Metal Pipeline (20 inch and

Larger)

Pumping Mud 3 12,000 0.10 0 0.000 0.000 0 0.000 0.000 0 0 5 Pumping Sand 1.5 6,000 0.10 0 0.000 0.000 0 0.000 0.000 0 0 5 Pumping Rock (Gravel) 0.5 2,000 0.10 0 0.000 0.000 0 0.000 0.000 0 0 5 Joints 3 12,000 0.10 0 0.000 0.000 0 0.000 0.000 0 0 30 Pontoons/Floats 12 60,000 0.10 0 0.000 0.000 0 0.000 0.000 0 0 5 SLV = Salvage Value HPF = Horsepower Factor G = Gas D = Diesel WLS = Water, Lube and Supplies RPR = Repairs

EP 1110-1-8, Vol. 430 Nov 11

4-11



Life Physical

Life Salvage Value



WLS %

RPR %

YRS HR SLV HPF G D HPF G D G D

Pipeline and Accessories (Ocean Environment)

Metal Pipeline (All sizes) Pumping Mud 2 9,000 0.40 0 0.000 0.000 0 0.000 0.000 0 0 5 Pumping Sand 1 4,500 0.40 0 0.000 0.000 0 0.000 0.000 0 0 5 Pumping Rock (Gravel) 0.3 1,500 0.40 0 0.000 0.000 0 0.000 0.000 0 0 5 Joints 1 4,500 0.40 0 0.000 0.000 0 0.000 0.000 0 0 5 Pontoons/Floats 2 9,000 0.40 0 0.000 0.000 0 0.000 0.000 0 0 5

Metal Pipeline On-Shore

Pumping Mud 3 12,000 0.10 0 0.000 0.000 0 0.000 0.000 0 0 5 Pumping Sand 1.5 6,000 0.10 0 0.000 0.000 0 0.000 0.000 0 0 5 Pumping Rock (Gravel) 0.5 2,000 0.10 0 0.000 0.000 0 0.000 0.000 0 0 5

Standby Calculation: Standby for pipeline and accessories shall be based on pumping mud.

SLV = Salvage Value HPF = Horsepower Factor G = Gas D = Diesel WLS = Water, Lube and Supplies RPR = Repairs

EP 1110-1-8, Vol. 430 Nov 11

ID No:

1.

a.(1)(2)(3) 2011(4) 1993(5) 3,730 hp(6)

(a) 200 hp(b) 1,325 hp(c) 750 hp(d) 200 hp

2,475 hp(7)

(a) $4,200,000(b) $0

$4,200,000

(8) 500 hrs/mo

(9)(a) Excessive Dredge Wear (Gravel) $8,000 /mo(b) $0 /mo(c) $0 /mo(d) $0 /mo(e) $0 /mo

$8,000 /mob.

(1) Labor Adjustment Factor (LAF) 1.04(2) Marine Diesel

$2.41(3) 2.500%(4) 2.000%

c.(1) Economic Index, Acquisition Year 4881(2) 8103

MARINE AND DREDGING PLANT INFORMATION AND EXPENSE FACTORS

Region 04

Example: The piece of equipment shown is based on a known piece of equipment for illustration purposes only.

USE THIS WORKSHEET TO COMPUTE A MONTHLY AND HOURLY RATE FOR MARINE AND DREDGING PLANT

Hours Worked per Month (Effective Time)

Additive Item(s) (Monthly Costs To be Estimated)

Plant Pertinent Data:Equipment Description:

Electrical Generators

Capital ImprovementsTotal Plant Value

Hydraulic SystemCutter Head Drive

24" Hydraulic Cutter Suction DredgeEllicott Series 4900 Super Dragon

Present Year or Year of Use:Acquisition Year:

Horsepower (hp) - Secondary Engine Horsepower (hp) - Prime

Model and Series:

Input data, methodology and notes used in the following sections of this form are or have reference to EP 1110-1-8, CONSTRUCTION EQUIPMENT OWNERSHIP AND EXPENSE SCHEDULE (see chapter 4).

Hydraulic Water Jet

Plant Value:Acquisition Costs

Total Secondary hp

Appendix B, Area Factors Data

Fuel Cost Per GallonFuel type

Appendix E, Economic Index Data (EK 105)

Cost of Money Rate (undiscounted)Cost of Money Rate (discounted)

Economic Index, Present Year or Year of Use

Total Additive Items

Figure 4-2. Dredging Plant Ownership and Operating Rate Worksheet Page 1 of 4

EP 1110-1-8, Vol. 430 Nov 11

4-12

1.

d.(1) 9 months/yr

e.(1) 25 yrs(2) 130,000 hrs(3) 0.10(4) 0.045(5) 0.039(6) 22%(7) 1.30

2. ANNUAL OWNERSHIP PERCENTAGE FACTORS

a.

1.0 - SLV / N {1.e.(3)} {1.e.(1)}

1.0 - 0.10 / 25 yrs = 3.60% /yr

b.

(N-1) x (1+SLV)+2 x / 2N{1.e.(1)} {1.e.(3)} {Appendix B} {1.e.(1)}(25-1) x (1+ 0.10) + 2 x 2.000% / 50.00 = 1.14% /yr

c. = 4.74% /yr

3. OWNERSHIP COSTSa. Ownership per Year

Plant Value x {1.a.(7)(a)}

$4,200,000 x = $199,080.00 /yr

b. Monthly Ownership Expense

/ Months Available per Year{3.a.} {1.d.(1)}

$199,080.00 /yr / 9 months/yr rounded = $22,120.00 /mo

MARINE AND DREDGING PLANT INFORMATION AND EXPENSE FACTORS (Continued)

Region 04

Prime Engine Fuel Factor (gal/bhp-hr)

Figure 4-1, Available Time to Dredge By Region Data (See Chapter 4, paragraph 4.3 for guidance)

Table 4-1, Dredging Plant Cost Factors DataUseful Life (in Years) for Ownership (N)Physical Life (in Hours) for RepairsSLV (Salvage Value Factor)

Months Available Per Year (9 months is used for this example)

Secondary Engine Fuel Factor (gal/bhp-hr)WLS (Water, Lube & Supplies Factor) percentRPR (Repair Cost Factor)

(DEPR + FCCM)Total Ownership Percent Per Year

Ownership per Year

Depreciation Percent Per Year (DEPR)

Facilities Capital Cost of Money Percent Per Year (FCCM)

Total Ownership Percent Per Year (DEPR + FCCM)

Discounted Money Rate

{2.c.}4.74%


EP 1110-1-8, Vol. 430 Nov 11

4-13

4. OPERATING COSTS

a. Fuel Cost(1) Prime Engine Fuel

Fuel Factor x HP x Fuel Cost {1.e.(4)} {1.a.(5)} {1.b.(2)}

0.045 gal/bhp-hr x 3,730 x $2.41 = $404.52 /hr

(2) Secondary Engine Fuel

Fuel Factor x HP x{1.e.(5)} {1.a.(6)} {1.b.(2)}

0.039 gal/bhp-hr x 2,475 x $2.41 = $232.63 /hr

(3) Total Fuel (Prime Engine Fuel + Secondary Engine Fuel) = $637.15 /hr

b. Water, Lube, and Supply (WLS) Cost(1) Prime Engine WLS

WLS Factor x Hourly Fuel Cost{1.e.(6)} {4.a.(1)}0.22 x $404.52 /hr = $88.99 /hr

(2) Secondary Engine WLS WLS Factor x Hourly Fuel Cost

{1.e.(6)} {4.a.(2)}0.22 x $232.63 /hr = $51.18 /hr

(3) Total Fuel (Prime Engine WLS + Secondary Engine WLS) = $140.17 /hr

c. Repair Cost

(1) Economic Adjustment Factor (EAF)Economic Index for

Present Year or Year of Use /

Economic Index for Acquisition

Year{1.c.(2)} {1.c.(1)}8103 / 4881 = 1.660

(2) Repair Cost

Total Plant Value x RPR x EAF x LAF / Life in Hrs {1.a.(7)} {1.e.(7)} {4.c.(1)} {1.b.(1)} {1.e.(2)}

$4,200,000 x 1.30 x 1.660 x 1.04 / 130,000 = $72.51 /hr

Fuel Cost per Gallon

Region 04


EP 1110-1-8, Vol. 430 Nov 11

4-14

4. OPERATING COSTS (Continued)

d. Total Hourly Operating Cost (Fuel + WLS + Repairs) Fuel + WLS + Repairs

{4.a.(3)} {4.b.(3)} {4.c.(2)}$637.15 /hr + $140.17 /hr + $72.51 /hr = $849.83 /hr

e.

Total Hourly

Operating Cost xHrs Worked per

Mo{4.d.} {1.a.(8)}

$849.83 /hr x 500 hrs/mo rounded = $424,915.00 /mo

5. TOTAL MONTHLY RATE

a. Ownership {3.b.} = $22,120.00 /mo

b. Operating {4.e.} = $424,915.00 /mo

c. Total Estimated Additive Items {1.a.(9))} = $8,000.00 /mo

d. = $455,035.00 /mo{5.a.} + {5.b.} + {5.c.}

6. STANDBY ALLOWANCE

a. Standard Hourly Standby Expense

Monthly Ownership Expense /

Maximum hrs/mo = 30.4 days/mo x 24

hrs/day{3.b.}

$22,120.00 /mo / 730 hrs/mo = $30.30 /hr

b. Generator Fuel Allowance for Dredge (An additional generator fuel allowance may be allowed under certain circumstances. This allowance is applicable to dredges only.)

Generator HP /Total Secondary

HP xSecondary Fuel

Cost{1.a.(6)} {1.a.} {4.a.(2)}200 hp / 2,475 hp x $232.63 = $18.80 /hr

c. TOTAL HOURLY STANDBY ALLOWANCE FOR DREDGE

Standby Expense +Generator Fuel

Allowance{6.a.} {6.b.}

$30.30 /hr + $18.80 /hr = $49.10 /hr

Region 04

Monthly Operating Cost

TOTAL MONTHLY RATE


EP 1110-1-8, Vol. 430 Nov 11

4-15

APPENDIX A REFERENCES

Section I: Required Publications Section II: Related Publications Section III. FAR Reference Section IV: Ordering Publication Sample Equipment Rate Computation Worksheet

EP 1110-1-8, Vol. 430 Nov 11

A-1

APPENDIX A

REFERENCES SECTION I: REQUIRED PUBLICATIONS

Public Law 92-41. The Renegotiation Act of 1971 [PL 92-41 (85 Stat. 97)].

Federal Acquisition Regulation 15.4 Contract Pricing, Government Printing Office, Washington, DC.

. 30.101. Cost Accounting Standards, Part 30, Government Printing Office, Washington, DC.

. 31.105. Construction and Architect-Engineer Contracts, Government Printing Office, Washington, DC.

. 31.205-10. Cost of Money, Government Printing Office, Washington, DC.

. 31.205-36. Rental Costs, Government Printing Office, Washington, DC.

. 49.000. Termination of Contracts, Government Printing Office, Washington, DC.

. 52.230-2. Cost Accounting Standards, Government Printing Office, Washington, DC.

Engineer Federal Acquisition Regulation Supplement (EFARS). 31.105 Construction and Architect-Engineer Contracts, Regulation Supplement, Government Printing Office, Washington, DC.

. 31.105-100. Contract Clause, Government Printing Office, Washington, DC.

Engineer Regulation 1110-2-1302. 2008. Engineering and Design - Civil Works Cost Engineering, U.S. Army Corps of Engineers.

U.S. Department of Labor, Bureau of Labor Statistics. Producer Prices and Price Indexes, Government Printing Office, Washington, DC.

EP 1110-1-8, Vol. 430 Nov 11

A-2

SECTION II: RELATED PUBLICATIONS

. 2000. Caterpillar Performance Handbook, 31st ed, Peoria, Illinois.

. 2001. Caterpillar Performance Handbook, 32nd ed, Peoria, Illinois.

. 2004. Caterpillar Performance Handbook, 34th ed, Peoria, Illinois.






Caterpillar Tractor Company, Fundamentals of Earthmoving, Peoria, Illinois, 1975.

Energy Information Administration, Official Energy Statistics from the U.S. Government. Electric Power Monthly, Washington, DC.

. Petroleum Marketing Monthly, Washington, DC.

Equipment Watch. 2006. Green Guide for Off-Highway Trucks and Trailers, San Jose, California.

. 2006. Green Guide Volume I, San Jose, California.

. 2006. Green Guide Volume II, San Jose, California.

. 2006. Contractor’s Equipment Cost Guide.

. 2006. Cost Reference Guide.

Euclid, Inc. 1982. Euclid Hauler Handbook, 15th ed, Cleveland, Ohio.

Fiat-Allis Construction Machinery, Inc. 1983. Owning and Operating Costs, Springfield, Illinois.

International Harvester, Pay Line Division. 1975. Earthmoving Principles, Schaumburg, Illinois.

Koehring Company. 1981. Application Manual for Hydraulic Excavators and Shovels, 1st ed, Milwaukee, Wisconsin.

EP 1110-1-8, Vol. 430 Nov 11

A-3

Goodyear Commercial Tire Systems Engineering Data Book http://www.goodyeartrucktires.com/resources/publications.aspx

Goodyear Engineered Products, Veyance Technologies, http://www.goodyearep.com/productsDetail.aspx?id=4156.

Mitchell Industrial Tire Company (MITCO), www.mitco.com.

TITAN Tire Corporation, Tire Catalog, http://www.titanstore.com/.

Nichols, H L Jr. 2005. Moving the Earth, 5th ed, McGraw-Hill Professional; 5 edition (March 28, 2005).

R S Means Company, Inc. 2011. Labor Rates for the Construction Industry, 38th ed., Kingston, Massachusetts.

Terex Corporation. 1981. Production and Cost Estimating of Material Movement with Earthmoving Equipment, Hudson, Ohio.

EP 1110-1-8, Vol. 430 Nov 11

A-4

SECTION III: EFAR REFERENCE

EFARS PART 31 CONTRACT COST PRINCIPLE AND PROCEDURES

EAC 95-6

SUBPART 31.1 -- APPLICABILITY 31.105 Construction and Architect-Engineer Contracts. (d)(2)(i)(b) In this case, equipment ownership and operating costs shall be determined using the Construction Equipment Ownership and Operating Expense Schedule published by the U.S. Army Corps of Engineers. 31.105-100 Contract Statement. The contracting officer shall insert the statement at 52.231-5000 in all solicitations and contracts for construction within the United States that are expected to exceed the small purchase threshold. EFARS Clause - 52.231-5000 Equipment Ownership and Operating Expense Schedule. As prescribed in 31.105-100, insert the following clause in all solicitations and contracts for construction that are expected to exceed the small purchase threshold. EQUIPMENT OWNERSHIP AND OPERATING EXPENSE SCHEDULE (MAR 1995) – EFARS. (a) This clause does not apply to terminations. See 52.249-5000, Basis for Settlement of Proposals, and FAR Part 49, Termination of Contracts. (b) Allowable cost for construction and marine plant and equipment in sound workable condition owned or controlled and furnished by a contractor or subcontractor at any tier shall be based on actual cost data for each piece of equipment or groups of similar serial and series for which the Government can determine both ownership and operating costs from the contractor’s accounting records. When both ownership and operating costs cannot be determined for any piece of equipment or groups of similar serial or series equipment from the contractor’s accounting records, costs for that equipment shall be based upon the applicable provisions of EP 1110-1-8, Construction Equipment Ownership and Operating Expense Schedule, Region [Insert roman numeral for the appropriate region of the schedule]. Working conditions shall be considered to

EP 1110-1-8, Vol. 430 Nov 11

A-5

SECTION III: EFAR REFERENCE (Continued) be average for determining equipment rates using the schedule unless specified otherwise by the contracting officer. For equipment not included in the schedule, rates for comparable pieces of equipment may be used or a rate may be developed using the formula provided in the schedule. For forward pricing, the schedule in effect at the time of negotiations shall apply. For retroactive pricing, the schedule in effect at the time the work was performed shall apply. (c) Equipment rental costs are allowable, subject to the provisions of FAR 31.105, Construction and Architect-Engineer Contract, and FAR 31.205-36, Rental Costs. Rates for equipment rented from an organization under common control, lease-purchase arrangements, and sale-leaseback arrangements, will be determined using the schedule, except that actual rates will be used for equipment leased from an organization under common control that has an established practice of leasing the same or similar equipment or unaffiliated lessees. (d) When actual equipment costs are proposed and the total amount of the pricing action exceeds the small purchase threshold, the contracting officer shall request the contractor to submit either certified cost or pricing data, or partial/limited data, as appropriate. The data shall be submitted on Standard Form 1411, Contract Pricing Proposal Cover Sheet.

EP 1110-1-8, Vol. 430 Nov 11

A-6

SECTION IV. ORDERING PUBLICATION Previous editions of EP 1110-1-8 were distributed through the U.S. Government Bookstore. The EP 1110-1-8 is available as a download from http://140.194.76.129/publications/eng-pamphlets. Copies of this edition will not be distributed through the U.S. Government Bookstore. Compact Discs (CDs) are provided to a pre-publication mailing list. A limited number of CDs are also available while supplies last. Check CD availability prior to ordering: http://www.nww.usace.army.mil/html/offices/ed/c/default.asp. Requests for CDs may be placed by sending an e-mail to [email protected]. When ordering, please provide the following information and specify the quantity:

Title of Publication: EP 1110-1-8, Construction Equipment Ownership and Operating Expense Schedule

Region: Region I through XII Volume No. Volume No. 1 through No. 12 Media: Quantities:

CD

EP 1110-1-8, Vol. 430 Nov 11

A-7

Use this worksheet to compute rates for equipment that is not in this pamphlet.

1. EQUIPMENT INFORMATION AND EXPENSE FACTORS

ID No.: a. Equipment Specification Data:

(1) Equipment Description: (2) Model and Series: (3) Year of Use: (4) Year Manufactured: (5) Horsepower - Equipment: (6) Horsepower - Carrier: (7) Fuel type: - Equipment: gas/diesel off-road/diesel on-road/electric/air

- Carrier: gas/diesel off-road/diesel on-road/electric/air (8) Shipping Weight (cwt): (9) Tire size and number of tires: (Cost of tires based on year of use – see 1.a.(3) and

appendix F)

No. Size/Ply Unit Price Cost (a) Front (FT): $ $ (b) Drive (DT): $ $ (c) Trailing (TT): $ $ (d) Total Tire Cost: $

USE APPENDIX D TO COMPLETE THE FOLLOWING DATA:

b. Category and Subcategory Number: c. Hourly Expense Calculation Factors:

(1) Economic Key (EK): (2) Condition (C): Average or Severe or Difficult (3) Discount Code (DC): B = 7.5% (0.075) – or – S = 15.0% (0.15) (4) Life in Hours (LIFE): (5) Salvage Value Percentage (SLV): (6) Fuel Factor – Equipment [Electric (E) Gas (G) Diesel (D)]: (7) Fuel Factor – Carrier (E G D): (8) Filters, Oil, and Grease (FOG) Factor (E G D): (9) Tire Wear Factor:

(a) Front (FT): (b) Drive (DT): (c) Trailing (TT):

(10) Repair Cost Factor (RCF):

Equipment Rate Computation Worksheet (copy as needed).

Page 1 of 6

EP 1110-1-8, Vol. 430 Nov 11

A-8

2. EQUIPMENT VALUE a. List Price + Accessories: [at Year of Manufacture] =$

(1) Discount: (List Code) (Discount x es) Accessori Price +[1.c.(3)]

($ + $ ) x ( ) =-($ (2) Subtotal [2.a.] – [2.a.(1)] Subtotal=$ (3) Sales or Import Tax: Rate)(Tax x (Subtotal)

[2.a.(2)] [Appendix B]

($ ) x ( ) =+$

(4) Total Discounted Price: Subtotal: [2.a.(2)] + [2.a.(3)] Subtotal=$

b. Freight: cwt) per Rate (Freight x Weight)(Shipping[1.a.(8)] [Appendix B]

( cwt) x ($ /cwt) =+$

c. TOTAL EQUIPMENT VALUE (TEV): TOTAL[2.]:=$ [(2.a.(4)] + [(2.b)]

(See chapter 3 for used and overage equipment rate adjustments.) 3. DEPRECIATION PERIOD (N)

a. N (WHPY)) YearPer Hours (Working / (hr)) hours (LIFE = [1.c.(4)] [Appendix B] ( hr) / ( hr/yr) =

4. OWNERSHIP COST a. Depreciation

(1) Tire Cost Index (TCI):

= 1.a.(3)) on Based Index, (Tire / Mfg) of YrIndex, Tire( Tire Cost Index (TCI) [Appendix E, EK=100] [Appendix E, EK=100]

( ) / ( ) = (TCI)

(2) ) LIFE ( / Cost)]] (Tire x ) TCI ( [ - )]SLV ( - [1.0 x [(TEV)

[2.c.] [1.c.(5)] [4.a.(1)] [1.a.(9)(d)] [1.c.(4)]

[($ ) x [1.0 – ( )] – [( ) x ($ )]] / ( hr)

=$ /hr


Page 2 of 6

EP 1110-1-8, Vol. 430 Nov 11

A-9

4. OWNERSHIP COST (Continued) b. Facilities Capital Cost of Money (FCCM):

(1) Factor Value Avg )] N ([2.0x / 2.0] (SLV)] [1.0 x 1.0] - ) N [[( =++ [3.a.] [1.c.5.] [3.a.] (AVF)

[[( yr) – 1.0] x [1.0 + ( )] + 2.0] / [2.0 x ( yr)]

= (AVF)

(2) ) WHPY ( / Money)-of-Cost (Adjusted x ) AVF( x )TEV (

[2.c] [4.b.(1)] [Appendix B] [Appendix B]

($ ) x ( ) x ( ) / ( hr/yr) =$ /hr

c. TOTAL HOURLY OWNERSHIP COST: TOTAL [4.]: =$ /hr

[4.a.(2)] + [4.b.(2)]

5. OPERATING COST

a. Fuel Costs: (1) Equipment:

(Fuel Factor x (Horsepower (hp)) x (Fuel Cost Per Gallon (gal)) [1.c.(6)] [1.a.(5)] [Appendix B] ( ) x ( hp) x ($ / gal) =$ /hr

(2) Carrier:

(Fuel Factor) x (Horsepower) x (Fuel Cost Per Gallon) [1.c.(7)] [1.a.(6)] [Appendix B]

( ) x ( hp) x ($ /gal) =$ /hr

(3) Total Hourly Fuel Cost: Total [5.a.] =$ /hr [(5.a.(1)] + [5.a.(2)]

b. FOG Cost:

(1) Equipment:

(FOG Factor) x (Equipment Fuel Cost) x (Labor Adjustment Factor (LAF)) [1.c.(8)] [5.a.(1)] [Appendix B]

( ) x ($ /hr) x ( ) =$ /hr


Page 3 of 6

EP 1110-1-8, Vol. 430 Nov 11

A-10


(2) Carrier:

(FOG Factor) x (Carrier Fuel Cost) x (LAF) [1.c.(8)] [5.a.(2) [Appendix B]

( ) x ($ /hr) x ( ) =$ /hr

(3) Total Hourly FOG Cost: Total [5.b.] =$ /hr

[(5.b.(1)] + [5.b.(2)]

c. Alternative Fuel/FOG Cost: Total [5.c.] =$ /hr (See chapter 2, paragraph 24.d. for guidance on when to use.)

d. Repair Cost:

(1) Economic Adjustment Factor (EAF):

(EK is from [1.c.(1)])

(Economic Index for Year 1.a.(3)) / (Economic Index for Year 1.a.(4)) [Appendix E] [Appendix E]

( ) / ( ) = (EAF)



(RCF) x (EAF) x (LAF) = Repair Factor (RF) [1.c.(10)] [5.d.(1)] [Appendix B]

( ) x ( ) x ( ) = (RF)

(3) Repair Cost:

[(TEV) - [(TCI) x (Tire Cost )]] x (RF) / (LIFE) [2.c.] [4.a.(1)] [1.a.(9)(d)] [5.d.(2)] [1.c.(4)] [($ ) – [( ) x ($ )]] x ( ) / ( )

(4) Total Hourly Repair Cost: Total [5.d.] =$ /hr


Page 4 of 6

EP 1110-1-8, Vol. 430 Nov 11

A-11


e. Tire Wear Cost: (Use current price levels. See Appendix F)


[1.5 x (FT Cost)] / [1.8 x (FT Wear Factor) x (Maximum Tire Life Hours)] [1.a.(9)(a)] [1.c.(9)(a)] [Appendix G]

[1.5 x ($ )] / [1.8 x ( ) x ( /hr)]

=$ /hr


[1.5 x (DT Cost)] / [1.8 x (DT Wear Factor) x (Maximum Tire Life Hours)] [1.a.(9)(b)] [1.c.(9)(b)] [Appendix G] [1.5 x ($ )] / [1.8 x ( ) x ( /hr)]

=$ /hr


[1.5 x (TT Cost)] / [1.8 x (TT Wear Factor) x (Maximum Tire Life Hours)] [1.a.(9)(c)] [1.c.(9)(c)] [Appendix G]

[1.5 x ($ )] / [1.8 x ( ) x ( /hr)]

=$ /hr

(4) Total Tire Wear Cost: Total [5.e.] =$ /hr [Sum 5.e.(1) through 5.e.(3)]

f. Tire Repair Cost:

(Total Tire Wear Cost) x 0.15 x (LAF) [5.e.(4)] [Appendix B]

($ /hr) x 0.15 x ( ) Total [5.f.] =$ /hr

g. TOTAL HOURLY OPERATING COST: TOTAL [5.] =$ /hr [Sum 5.a. through 5.f.]


Page 5 of 6

EP 1110-1-8, Vol. 430 Nov 11

A-12


6. HOURLY RATES

a. Total Hourly Rate: [based on 40 hours per week (wk)] (Ownership Cost) + (Operating Cost)

($ /hr) + ($ /hr) =$ /hr

b. Other Work Shifts Hourly Rate: (Refer to Chapter 3, Adjustments to Rates, for methodology.) [(Depreciation) + [(FCCM) x (40 hr/wk) / (Work hr/wk)] + (Operating Cost)] [4.a.(2)] [4.b.(2)] (example: 60 hr/wk) [5.g.] [($ /hr) + [($ /hr) x (40 hr/wk) / ( hr/wk)] + ($ /hr)] =$ /hr

c. Standby Hourly Rate:

[(Depreciation) x 0.50] + (FCCM) [4.a.(2)] [4.b.(2)]

[($ /hr) x 0.50] + ($ /hr) =$ /hr)


Page 6 of 6

EP 1110-1-8, Vol. 430 Nov 11

A-13


EP 1110-1-8, Vol. 430 Nov 11

A-14

APPENDIX B AREA FACTORS

EP 1110-1-8, Vol. 430 Nov 11

B-1

APPENDIX B

Region: 4NORTHCENTRAL

AREA FACTORS

EP 1110-1-8(Vol. 4)

11/30/2011

Total State Sales or Import Tax Rate: 5.55%Working Hours Per Year (WHPY): 1,260

Labor Adjustment Factor (LAF): 1.04

Electricity Cost Per Kilowatt-Hour: $0.081

Gasoline Cost Per Gallon: $3.61Diesel Cost Per Gallon (Off-Road Use): $3.40Diesel Cost Per Gallon (On-Road Use): $3.90Cost-of-Money Rate (Full Rate): 2.500%

Cost-of-Money Rate (Adjusted): 2.000%

over 240cwt thru $17.33





over 800cwt thru $6.50cwt thru $4.97

240300400500700800

99,999

over 0

Freight Rates

hrs/yr

/kW-Hr

/gal

/gal/gal

B-1

EP 1110-1-8, Vol. 430 Nov 11

B-2

APPENDIX B

Below is a listing of all regional area factors for reference only. The area factor's used for this pamphlet are located on previous page B-1.

EP 1110-1-8

11/30/2011(Vol. 1) AREA FACTORS (for all regions)

Freight Cost

Reg SST WHPY LAF Elec Gas D-Off D-On Thru CWT $ Thru CWT $ Thru CWT $ Thru CWT $ Thru CWT $ Thru CWT $ Thru CWT $

1 NORTHEAST 2011 5.95% 1360 1.12 $0.138 $3.70 $3.28 $3.81 240 $18.08 300 $16.61 400 $14.46 500 $12.44 700 $6.96 800 $6.96 99,999 $10.55

2 MIDEAST 2011 5.90% 1450 1.01 $0.096 $3.62 $3.36 $3.90 240 $9.67 300 $8.90 400 $8.01 500 $7.19 700 $4.67 800 $4.67 99,999 $7.09

3 SOUTHEAST 2011 8.35% 1530 0.86 $0.087 $3.40 $3.29 $3.75 240 $15.58 300 $14.19 400 $12.14 500 $10.20 700 $6.13 800 $6.13 99,999 $9.25

4 NORTHCENTRAL 2011 5.55% 1260 1.04 $0.081 $3.61 $3.40 $3.90 240 $17.33 300 $16.01 400 $14.20 500 $12.56 700 $7.09 800 $6.50 99,999 $4.97

5 MIDWEST 2011 7.50% 1400 0.98 $0.077 $3.49 $3.41 $3.91 240 $13.50 300 $12.00 400 $10.79 500 $9.32 700 $5.72 800 $5.30 99,999 $4.05

6 SOUTHWEST 2011 8.10% 1590 0.87 $0.082 $3.42 $3.57 $4.00 240 $17.56 300 $16.39 400 $14.76 500 $13.26 700 $7.25 800 $6.67 99,999 $5.18

7 WEST 2011 8.30% 1630 1.13 $0.097 $3.53 $3.32 $3.92 240 $28.04 300 $26.16 400 $23.46 500 $20.96 700 $10.67 800 $9.37 99,999 $6.88

8 NORTHWEST 2011 5.40% 1540 1.05 $0.072 $3.67 $3.45 $3.99 240 $28.32 300 $26.60 400 $24.23 500 $22.06 700 $11.26 800 $9.51 99,999 $6.48

9 ALASKA 2011 4.15% 1040 1.19 $0.138 $4.00 $3.84 $4.08 240 $57.86 300 $48.54 400 $38.46 500 $41.99 700 $29.86 800 $27.94 99,999 $24.59

10 HAWAII 2011 4.50% 1480 1.22 $0.254 $4.33 $3.51 $4.22 240 $104.68 300 $59.12 400 $51.62 500 $51.62 700 $44.98 800 $42.31 99,999 $26.03

11 PUERTO RICO 2011 7.00% 1560 0.71 $0.226 $3.18 $3.31 $3.77 240 $48.34 300 $32.48 400 $28.19 500 $26.45 700 $19.79 800 $17.71 99,999 $13.81

12 KWAJALEIN 2011 4.50% 1390 1.02 $0.254 $3.70 $3.51 $4.22 240 $30.46 300 $28.37 400 $25.42 500 $22.70 700 $12.23 800 $10.61 99,999 $8.09

B- 2SST = State Sales tax WHPY = Work Hours Per Year LAF = Labor Adjustment Factor Elec = Electricty Cost Per kW-Hr Gas = Gasoline Cost per Gal D-Off = Diesel-Off Road Cost per Gal D-On = Diesel-On Road Cost per Gal CWT = Hundred Pounds

EP 1110-1-8, Vol. 430 Nov 11

B-3


EP 1110-1-8, Vol. 430 Nov 11

B-4

APPENDIX C GUIDE FOR SELECTING OPERATING CONDITIONS

EP 1110-1-8, Vol. 430 Nov 11

C-1


EQUIPMENT TYPE AVERAGE SEVERE B25 and B35: Buckets Clamshell or Dragline Depreciation Period:

Working in gravels, silts, and sands at low impact freshwater environment. 8,000 - 10,000 hours

Working in rock, hard digging, high impact, or saltwater environment. 6,500 - 8,000 hours

C80 and C90: Cranes Hydraulic, Truck Mounted

Mechanical, Truck Mounted

Depreciation Period:

Lift less than rated capacity, intermittent duty. 14,000 - 20,000 hours

Continuous lift near rated capacity, excessive swing, abrasive materials, sloped surfaces, and saltwater environment. 12,000 - 18,000 hours

C85: Cranes Mechanical Dragline,

Lifting, or Clamshell Crawler Mounted Depreciation Period:

Gravels, silts, pull, and lift less than rated capacity. 14,000 - 22,000 hours

Highly abrasive materials, impact breakout, continuous load near rated capacity, and saltwater environment. 12,000 - 18,000 hours

G10: Generators Depreciation Period:

Working below rated capacity, good field conditions. 8,000 - 10,000 hours

Working at or above rated capacity, poor field conditions, such as saltwater. 7,000 - 8,000 hours

EP 1110-1-8, Vol. 430 Nov 11

C-2


EQUIPMENT TYPE AVERAGE SEVERE G15: Graders, Motor Depreciation Period:

Haul road maintenance; road construction, ditching; loose fill spreading; landforming, landleveling; summer road maintenance with medium to heavy winter snow removal; and elevating grader use. 14,500 hours

Maintenance of hard-packed roads with embedded rock; heavy fill spreading; ripping scarifying of asphalt or concrete; continuous high load factor; and high impact. 13,500 hours

H25: Hydraulic Excavators Crawler Mounted Depreciation Period:

Mass excavation or trenching where machine digs all the time in natural bed clay soils; some traveling and steady, full throttle operation; and most log loading operations.

8,500 - 19,000 hours

Continuous trenching or truck loading in rock or shot rock soils; large amount of travel over rough ground; machine continuously working on rock floor with constant high load factor and high impact; and saltwater environment. 7,000 – 15,000 hours

H30: Hydraulic Excavators Wheel Mounted Depreciation Period:

Continuous digging in sandy clay/sandy gravel, site development, and lumber yard applications. 8,000 - 10,000 hours

Continuous digging in rock/natural bed clay, high impact, using hammer, and working in forests or quarries. 6,500 - 8,000 hours

H35: Hydraulic Shovels Crawler Mounted

Continuous loading in well shot rock or fairly tight

Continuous loading in poorly shot rock, virgin, or

EP 1110-1-8, Vol. 430 Nov 11

C-3


EQUIPMENT TYPE AVERAGE SEVERE (nonelectric)

Depreciation Period:

bank. Good underfoot conditions: dry floor, little impact, or sliding on undercarriage.

14,000 - 18,000 hours

lightly blasted tight banks. Adverse underfoot conditions: rough floors, high impact sliding on undercarriage; and saltwater environment. 12,000 - 16,000 hours

L10: Land Clearing Equipment Depreciation Period:

Working in low impact conditions at or below rated capacity. 10,000 hours

High impact conditions working at or above rated capacity. 7,000 hours

L30: Loaders, Belt (conveyors) Depreciation Period:

Working below rated capacity, with intermittent service. 10,000 hours

Working at or above rated capacity with continuous service. 8,000 hours

L35: Loaders, Front End Crawler Type Depreciation Period:

Bank excavation, intermittent ripping, basement digging of natural bed clays, sands, silts, and gravels; some traveling; and steady full throttle operations. 10,000 hours

Loading shot rock, cobbles, glacial till, and caliche; steel millwork; high density materials in standard bucket; continuous work on rock surfaces; large amount of ripping of tight rock materials; high impact conditions; and saltwater environment. 8,000 hours

EP 1110-1-8, Vol. 430 Nov 11

C-4


EQUIPMENT TYPE AVERAGE SEVERE L40: Loaders, Front End Wheel Type (does not include skid steer and tool carriers) Depreciation Period:

Continuous truck loading from stockpile; low to medium density materials in properly sized bucket; hopper charging in low to medium rolling resistance; loading from bank in good digging; and load and carry on poor surfaces and slight adverse grades. 9,250 - 13,500 hours

Loading shot rock (large loaders); handling high density materials with counterweighted machine; steady loading from very tight banks; continuous work on rough or very soft surfaces; load and carry in hard digging; travel longer distances on poor surfaces with adverse grades and saltwater environment. 8,750 - 12,000 hours

L45 and L50: Loaders with Backhoe Crawler Type and Wheel Type Depreciation Period:

Utility applications in medium to heavy soil; occasional use of constant flow implements and dig depths to 3.05 meters (10 feet). 8,000 hours

Production applications or digging in rock; regular use of constant flow implements; and dig depths over 3.05 meters (10 feet). 6,000 hours

L60: Log Skidders Depreciation Period:

Continuous turning, steady skidding for medium distances with moderate decking. Good underfooting: dry floor with few stumps and gradual rolling terrain. 10,000 hours

Continuous turning, steady skidding for long distances with frequent decking; poor underfoot conditions: wet floor, steep slopes, and numerous stumps; and saltwater environment. 8,000 hours

EP 1110-1-8, Vol. 430 Nov 11

C-5


EQUIPMENT TYPE AVERAGE SEVERE M10 - .31 and .32: Clamshell dredges < 5 cy Amphibious Excavator Depreciation Period:

Gravel, silts, breakout force at less than capacity, freshwater conditions. 10,000 - 20,000 hours

Rock, abrasive materials, load at rated capacity, saltwater conditions. 9,000 - 18,000 hours

M10 - .51 and .53: Boats, Skiffs, Crew Boats, Work Boats, Survey Boats, and Launches Depreciation Period:

Freshwater applications, light waves, and steady to light use. 16,000 - 18,000 hours

Saltwater use, medium to high waves, heavy use. 13,000 - 15,000 hours

P35: Pipelayers Depreciation Period:

Typical pipelayer use in operating conditions ranging from very good to severe. 14,000 hours

Continuous use in deep mud or water or on rock surfaces. 11,500 hours

R10: Rippers and Bank Slopers Depreciation Period:

Light rock, medium breakout force required. 8,000 hours

Hard rock, excessive wear due to high breakout force. 6,500 hours

S10, S15, S20, and S25: Scrapers Self-Propelled Tractor Drawn Soil Stabilizers Depreciation Period:

Varying loading and haul road conditions; long and short hauls; adverse and favorable grades; some impact; and typical road-building use on a variety of jobs. 10,000 - 15,000 hours

High impact conditions, such as loading ripped rock; overloading, continuous high total resistance conditions; and rough haul roads. 8,000 - 13,500 hours

EP 1110-1-8, Vol. 430 Nov 11

C-6


EQUIPMENT TYPE AVERAGE SEVERE T15: Tractors Crawler (Dozer) Depreciation Period:

Production dozing in clays, sands, gravels, and talus rock. Push-loading scrapers, borrow pit ripping, most land clearing and skidding applications. Medium impact conditions. Production landfill work. 10,000 - 15,000 hours

Heavy rock ripping; tandem ripping; pushloading and dozing in hard rock; work on rock surfaces; continuous high impact conditions; and saltwater environment. 8,000 - 12,500 hours

T20: Tractors Wheel Type (Dozer) Depreciation Period:

Production dozing, push loading in clays, sands, silts, loose gravels; and shovel cleanup. 14,000 hours

Production dozing in rock; push loading in rocky, boulder strewn borrow pits; high impact conditions; and landfill compactor work. 13,000 hours

T30: Trenchers Chain and Wheel Type Depreciation Period:

Working in sands and silts below rated capacity of the machine. 8,000 hours

Working in gravels and abrasive materials at or above the rated capacity of the machine. 6,000 hours

T45 and T50: Truck Trailers Trucks, Highway Depreciation Period:

Varying loading and road conditions; and typical construction use on a variety of jobs. 8,000 - 12,000 hours

Consistently poor road conditions; and oversized loading equipment. 6,500 - 10,000 hours

EP 1110-1-8, Vol. 430 Nov 11

C-7


EQUIPMENT TYPE AVERAGE SEVERE T55 and T60: Truck, Off-Highway Trucks, Water, Off-Highway (Articulated and Rigid) Depreciation Period:

Varying load and haul road conditions; high rolling resistance and poor traction during part of the job; some adverse grades; some impact loads; and typical use in road building, dam construction, open-pit mining, etc. 12,000 - 20,000 hours

Continuous use on very poorly maintained haul roads, high rolling resistance, and poor traction; frequent adverse grades and high impact loads; and poorly matched loading equipment with continuous overloading. 10,000 - 18,000 hours

W10 and W15: Wagons Bottom Dump Rear Dump Chapter 1 Depreciation Period:

Varying load and haul road conditions; long and short hauls; high rolling resistance and poor traction during part of the job; some adverse grades; some impact; typical road building use in a variety of jobs; and dam construction, open-pit mining, etc. 12,000 hours

Continuous use on very poorly maintained haul roads, high rolling resistance, and poor traction; high impact conditions, such as loading ripped rock; frequent adverse grades and high impact loads; and poorly matched loading equipment with continuous overloading. 10,000 hours

EP 1110-1-8, Vol. 430 Nov 11

C-8

APPENDIX D EQUIPMENT HOURLY CALCULATION FACTORS

EP 1110-1-8, Vol. 430 Nov 11

D-1

CATEGORY

SUB DESCRIPTION EK C DC LIFE SLV D TT RCFDTFTGEHPF DGEHPF DGEFUEL FACTORS

EQUIPMENT

FUEL FACTORS

CARRIER FOG TIRE WEAR

FACTORS

EQUIPMENT HOURLY CALCULATION FACTORS

EP 1110-1-8

11/30/2011(Vol. 1)

FACTORS

APPENDIX D

A10 0.00 1AGGREGATE / CHIP SPREADERSA10 0.10 10 A B 8,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .000 .102 .102 0.83 0.72 0.92 0.75 SELF-PROPELLEDA10 0.20 10 A B 6,000 0.20 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.73 0.00 0.82 0.60 TOWED & TAILGATEA15 0.00 1AIR COMPRESSORS, PORTABLEA15 0.10 5 A B 10,000 0.20 75 .750 .068 .036 0 .000 .000 .000 .477 .136 .119 0.66 0.00 0.73 0.75 ROTARY SCREWA15 0.20 5 A B 12,000 0.15 75 .750 .068 .036 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.65 SHOP TYPEA20 0.00 1AIR HOSE, TOOLS & EQUIPMENTA20 0.10 5 A B 3,500 0.05 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 1.50 AIR DRILL HOSEA20 0.20 5 A B 3,500 0.05 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 1.65 SANDBLAST HOSEA20 0.30 5 A B 6,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 0.96 0.84 1.07 1.50 SANDBLASTERS, BREAKERS, & MISC. AIR TOOLSA25 0.00 10 A B 6,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .119 0.96 0.63 1.07 0.85ASPHALT PAVING DISTRIBUTORSA30 0.00 1ASPHALT PAVERS & MISCELLANEOUS ROAD

EQUIPMENTA30 0.10 10 A B 8,000 0.15 70 .700 .063 .034 0 .000 .000 .000 .000 .136 .119 1.08 0.72 1.20 1.00 SELF PROPELLEDA30 0.20 10 A B 10,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .119 1.08 0.00 1.20 0.80 TOWEDA30 0.30 10 A B 12,000 0.20 60 .600 .054 .029 13 .130 .012 .006 .000 .100 .100 1.08 0.71 1.20 0.55 SLURRY SEAL PAVERS (Cold mix)A30 0.40 10 A B 10,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .119 1.08 0.71 1.20 0.80 MISCELLANEOUS ROAD EQUIPMENTA35 0.00 10 A B 6,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .119 1.08 0.71 1.20 0.80ASPHALT PAVING KETTLESA40 0.00 10 A B 6,000 0.20 95 .950 .086 .045 0 .000 .000 .000 .000 .136 .119 1.08 0.71 1.20 1.00ASPHALT & CONCRETE MILLERS / PROFILERS /

PLANERS / ROTARY GRINDERSA45 0.00 10 A B 5,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .119 1.08 0.71 1.20 0.90ASPHALT RECYCLERS & SEALERSB10 0.00 1BATCH PLANTS, ASPHALT & CONCRETEB10 0.10 10 A B 8,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 1.08 0.72 1.20 1.00 ASPHALT

D- 1EK=Economic Key (Appendix E) LIFE=Economic Life E=Electric Powered FT=Front Tire C=Operating Conditions (A=average, S=severe) SLV=Salvage Value G=Gas Powered DT=Drive Tire DC=Discount Code (B=basic 7.5%, S=special 15%) HPF=Horsepower Factor D=Diesel Powered TT=Trailing Tire RCF=Repair Cost Factor

EP 1110-1-8, Vol. 430 Nov 11

D-2

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

11/30/2011(Vol. 1)

FACTORS

APPENDIX D

B10 0.20 10 A B 8,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 1.08 0.71 1.20 1.00 CONCRETEB10 0.30 10 A B 10,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 1.08 0.71 1.20 1.00 PUGMILLB15 0.00 95 A B 8,000 0.10 65 .650 .059 .031 13 .130 .012 .006 .000 .102 .119 0.96 0.63 1.07 0.80BROOMS, STREET SWEEPERS & FLUSHERSB20 0.00 95 A B 8,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .119 0.00 0.00 0.92 0.90BRUSH CHIPPERSB25 0.00 15 A B 8,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.70BUCKETS, CLAMSHELLB25 0.00 15 S B 6,500 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.80BUCKETS, CLAMSHELLB30 0.00 1BUCKETS, CONCRETEB30 0.10 15 A B 8,000 0.05 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.70 GENERAL PURPOSE, MANUAL TRIPB30 0.20 15 A B 8,000 0.05 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.75 LAYDOWNB30 0.30 15 A B 8,000 0.05 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.80 LOWBOYB30 0.40 15 A B 8,000 0.05 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.80 LOW SLUMPB35 0.00 1BUCKETS, DRAGLINEB35 0.10 15 A B 8,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.70 LIGHT WEIGHTB35 0.10 15 S B 6,500 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.80 LIGHT WEIGHTB35 0.20 15 A B 9,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.70 MEDIUM WEIGHTB35 0.20 15 S B 7,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.80 MEDIUM WEIGHTB35 0.30 15 A B 10,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.70 HEAVY WEIGHTB35 0.30 15 S B 8,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.80 HEAVY WEIGHTC05 0.00 95 A B 2,000 0.10 90 .900 .081 .043 0 .000 .000 .000 .477 .136 .161 0.00 0.00 0.00 2.50CHAIN SAWSC10 0.00 1COMPACTORS, WALK-BEHIND OR REMOTE

CONTROLLERC10 0.10 95 A B 4,000 0.05 90 .900 .081 .043 0 .000 .000 .000 .477 .102 .102 0.00 0.00 0.00 1.20 COMPACTORS, RAMMERS / TAMPERS &

VIBRATORY PLATES


EP 1110-1-8, Vol. 430 Nov 11

D-3

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

11/30/2011(Vol. 1)

FACTORS

APPENDIX D

C10 0.20 95 A B 4,000 0.15 90 .900 .081 .043 0 .000 .000 .000 .477 .102 .102 0.00 0.00 0.00 1.20 ROLLERS, VIBRATORYC15 0.00 1 ACONCRETE CLEANERS / ABRASIVE BLASTERSC15 0.10 95 A B 4,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .530 .136 .119 0.00 0.00 0.00 0.90 WALK BEHINDC15 0.20 95 A B 8,000 0.20 95 .950 .086 .045 50 .500 .045 .024 .000 .136 .119 0.72 0.66 0.79 0.90 TRUCK/TRAILER MOUNTEDC20 0.00 95 A B 4,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .530 .136 .119 0.96 0.63 1.07 0.70CONCRETE BUGGIESC25 0.00 1CONCRETE FINISHERS/SCREEDS/SPREADERSC25 0.10 95 A B 5,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .530 .136 .119 0.00 0.00 0.00 0.80 FINISHERS/TROWELSC25 0.20 95 A B 5,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .530 .136 .119 0.96 0.84 1.07 0.80 VIBRATORY SCREEDC25 0.25 95 A B 8,000 0.30 65 .650 .059 .031 0 .000 .000 .000 .000 .180 .160 0.96 0.84 1.07 0.60 VIBRATORY LASER SCREEDC25 0.30 95 A B 8,000 0.30 65 .650 .059 .031 0 .000 .000 .000 .000 .180 .160 0.96 0.84 1.07 0.60 MATERIAL/TOPPING SPREADERSC30 0.00 95 A B 5,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .530 .136 .119 0.00 0.00 0.00 0.90CONCRETE GRINDERSC35 0.00 95 A B 7,000 0.25 75 .750 .068 .036 0 .000 .000 .000 .477 .136 .119 0.96 0.86 1.07 0.90CONCRETE GUNITERS / SHOTCRETERSC40 0.00 95 A B 5,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .530 .136 .119 0.00 0.00 0.92 0.80CONCRETE MIXING UNITSC45 0.00 10 A B 6,000 0.20 75 .750 .068 .036 0 .000 .000 .000 .000 .136 .119 1.08 0.72 1.20 1.00CONCRETE PAVING MACHINESC55 0.00 95 A B 8,000 0.10 70 .700 .063 .034 10 .100 .009 .005 .477 .136 .119 0.96 0.86 1.07 1.00CONCRETE PUMPSC60 0.00 95 A B 6,000 0.10 90 .900 .081 .043 0 .000 .000 .000 .477 .136 .161 0.00 0.00 0.00 1.00CONCRETE SAWS (Add cost for sawblade wear)C65 0.00 5 A B 4,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .161 0.00 0.00 0.00 2.50CONCRETE VIBRATORSC70 0.00 1CRANES, GANTRY & STRADDLEC75 0.00 20 A B 14,000 0.15 75 .750 .068 .036 0 .000 .000 .000 .000 .136 .127 0.66 0.59 0.73 0.80CRANES, HYDRAULIC, SELF-PROPELLEDC80 0.00 1CRANES, HYDRAULIC, TRUCK MOUNTEDC80 0.01 20 A B 14,000 0.15 65 .650 .059 .031 10 .100 .009 .005 .000 .161 .153 0.66 0.58 0.73 0.60 UNDER 26 TONC80 0.01 20 S B 12,000 0.15 85 .850 .077 .041 13 .130 .012 .006 .000 .161 .153 0.18 0.14 0.20 0.65 UNDER 26 TON


EP 1110-1-8, Vol. 430 Nov 11

D-4

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

11/30/2011(Vol. 1)

FACTORS

APPENDIX D

C80 0.02 20 A B 16,000 0.15 65 .650 .059 .031 10 .100 .009 .005 .000 .127 .110 0.66 0.58 0.73 0.70 26 TON THRU 65 TONC80 0.02 20 S B 14,000 0.15 85 .850 .077 .041 13 .130 .012 .006 .000 .127 .110 0.18 0.14 0.20 0.75 26 TON THRU 65 TONC80 0.03 20 A B 18,000 0.15 65 .650 .059 .031 10 .100 .009 .005 .000 .127 .110 0.66 0.58 0.73 0.80 66 TON THRU 125 TONC80 0.03 20 S B 16,000 0.15 85 .850 .077 .041 13 .130 .012 .006 .000 .127 .110 0.18 0.14 0.20 0.85 66 TON THRU 125 TONC80 0.04 20 A B 20,000 0.15 65 .650 .059 .031 10 .100 .009 .005 .000 .127 .110 0.66 0.58 0.73 0.90 OVER 125 TONC80 0.04 20 S B 18,000 0.15 85 .850 .077 .041 13 .130 .012 .006 .000 .127 .110 0.18 0.14 0.20 0.95 OVER 125 TONC85 0.00 1CRANES, MECHANICAL, LATTICE BOOM, CRAWLER

MOUNTEDC85 0.11 20 A B 14,000 0.20 55 .550 .050 .026 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 0.80 DRAGLINE, CLAMSHELL, 0 THRU 1.0 CYC85 0.11 20 S B 12,000 0.20 72 .720 .065 .034 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 0.90 DRAGLINE, CLAMSHELL, 0 THRU 1.0 CYC85 0.12 20 A B 16,000 0.20 55 .550 .050 .026 0 .000 .000 .000 .000 .144 .144 0.00 0.00 0.00 0.85 DRAGLINE, CLAMSHELL, OVER 1.0 CY THRU 2.5

CYC85 0.12 20 S B 13,000 0.20 72 .720 .065 .034 0 .000 .000 .000 .000 .144 .144 0.00 0.00 0.00 0.95 DRAGLINE, CLAMSHELL, OVER 1.0 CY THRU 2.5

CYC85 0.13 20 A B 18,000 0.20 55 .550 .050 .026 0 .000 .000 .000 .000 .093 .093 0.00 0.00 0.00 0.95 DRAGLINE, CLAMSHELL, OVER 2.5 CY THRU 5.0

CYC85 0.13 20 S B 15,000 0.20 72 .720 .065 .034 0 .000 .000 .000 .000 .093 .093 0.00 0.00 0.00 1.05 DRAGLINE, CLAMSHELL, OVER 2.5 CY THRU 5.0

CYC85 0.14 20 A B 20,000 0.20 55 .550 .050 .026 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.00 1.05 DRAGLINE, CLAMSHELL, OVER 5.0 CYC85 0.14 20 S B 16,000 0.20 72 .720 .065 .034 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.00 1.15 DRAGLINE, CLAMSHELL, OVER 5.0 CYC85 0.21 20 A B 16,000 0.20 40 .400 .036 .019 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 0.65 LIFTING, 0 THRU 25 TONC85 0.21 20 S B 13,000 0.20 52 .520 .047 .025 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 0.70 LIFTING, 0 THRU 25 TONC85 0.22 20 A B 18,000 0.20 40 .400 .036 .019 0 .000 .000 .000 .000 .085 .085 0.00 0.00 0.00 0.75 LIFTING, 26 TON THRU 50 TONC85 0.22 20 S B 15,000 0.20 52 .520 .047 .025 0 .000 .000 .000 .000 .085 .085 0.00 0.00 0.00 0.80 LIFTING, 26 TON THRU 50 TON


EP 1110-1-8, Vol. 430 Nov 11

D-5

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

11/30/2011(Vol. 1)

FACTORS

APPENDIX D

C85 0.23 20 A B 20,000 0.15 40 .400 .036 .019 0 .000 .000 .000 .000 .093 .093 0.00 0.00 0.00 0.85 LIFTING, 51 TON THRU 150 TONC85 0.23 20 S B 16,000 0.15 52 .520 .047 .025 0 .000 .000 .000 .000 .093 .093 0.00 0.00 0.00 0.90 LIFTING, 51 TON THRU 150 TONC85 0.24 20 A B 22,000 0.15 40 .400 .036 .019 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.00 0.95 LIFTING, OVER 150 TONC85 0.24 20 S B 18,000 0.15 52 .520 .047 .025 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.00 1.00 LIFTING, OVER 150 TONC90 0.00 1CRANES, MECHANICAL, LATTICE BOOM, TRUCK

MOUNTEDC90 0.01 20 A B 14,000 0.15 50 .500 .045 .024 10 .100 .009 .005 .000 .161 .153 0.66 0.58 0.73 0.60 UNDER 26 TONC90 0.01 20 S B 12,000 0.15 65 .650 .059 .031 13 .130 .012 .006 .000 .161 .153 0.18 0.14 0.20 0.65 UNDER 26 TONC90 0.02 20 A B 16,000 0.15 50 .500 .045 .024 10 .100 .009 .005 .000 .127 .110 0.66 0.58 0.73 0.70 26 TON THRU 65 TONC90 0.02 20 S B 14,000 0.15 65 .650 .059 .031 13 .130 .012 .006 .000 .127 .110 0.18 0.14 0.20 0.75 26 TON THRU 65 TONC90 0.03 20 A B 18,000 0.20 50 .500 .045 .024 10 .100 .009 .005 .000 .127 .110 0.66 0.58 0.73 0.80 66 TON THRU 125 TONC90 0.03 20 S B 16,000 0.20 65 .650 .059 .031 13 .130 .012 .006 .000 .127 .110 0.18 0.14 0.20 0.85 66 TON THRU 125 TONC90 0.04 20 A B 20,000 0.20 50 .500 .045 .024 10 .100 .009 .005 .000 .127 .110 0.66 0.58 0.73 0.90 OVER 125 TONC90 0.04 20 S B 18,000 0.20 65 .650 .059 .031 13 .130 .012 .006 .000 .127 .110 0.18 0.14 0.20 0.95 OVER 125 TONC95 0.00 20 A B 18,000 0.20 65 .650 .059 .031 10 .100 .009 .005 .530 .127 .110 0.00 0.00 0.92 0.85CRANES, TOWERD10 0.00 1DRILLS, AIR/HYDRAULIC,CRWLR MTD,0" THRU 6.5"

DIA HOLE (Add cost for drill steel and bit wear)D10 0.10 25 A B 14,000 0.25 80 .800 .072 .038 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 1.00 DRILLS, AIR TRACK (Add cost for drill steel and bit

wear)D10 0.20 25 A B 10,000 0.25 80 .800 .072 .038 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 1.00 DRILLS, HYDRAULIC TRACK (Add cost for drill steel

and bit wear)D15 0.00 1DRILLS, HORIZONTALD15 0.10 25 A B 10,000 0.25 80 .800 .072 .038 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.90DRILLS, HORIZONTAL BORING & GROUND

PIERCING (Add cost for drill steel and bit wear)


EP 1110-1-8, Vol. 430 Nov 11

D-6

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

11/30/2011(Vol. 1)

FACTORS

APPENDIX D

D15 0.20 25 A B 10,000 0.25 80 .800 .072 .038 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.90DRILLS, HORIZONTAL & DIRECTIONAL (Add cost for drill steel and bit wear)

D20 0.00 25 A B 8,000 0.25 80 .800 .072 .038 0 .000 .000 .000 .477 .068 .102 0.00 0.00 0.00 0.85DRILLS, CORE, COLUMN MOUNTED (Add cost for drill steel and bit wear)

D25 0.00 25 A B 10,000 0.25 80 .800 .072 .038 0 .000 .000 .000 .477 .068 .102 0.00 0.00 0.92 1.00DRILLS, CORE & DOWELLING (Add cost for drill steel and bit wear)

D30 0.00 25 A B 10,000 0.25 80 .800 .072 .038 10 .100 .009 .005 .477 .136 .119 0.96 0.86 1.07 1.00DRILLS, EARTH / AUGER (Add cost for drill steel and cutting edge wear)

D35 0.00 1DRILLS, ROTARY BLASTHOLE (Add cost for drill steel and bit wear)

D35 0.11 25 A B 14,000 0.20 80 .800 .072 .038 10 .100 .009 .005 .005 .161 .161 0.00 0.00 0.00 1.00 DIESEL, 4.5" THRU 9.875" DIAMETER HOLE (Add cost for drill steel and bit wear)

D35 0.12 25 A B 18,000 0.20 80 .800 .072 .038 10 .100 .009 .005 .011 .136 .136 0.96 0.86 1.07 1.00 DIESEL, OVER 9.875" DIAMETER (Add cost for drill steel and bit wear)

D35 0.21 25 A B 14,000 0.20 70 .700 .063 .034 10 .100 .009 .005 .530 .000 .000 0.00 0.00 0.00 0.55 ELECTRIC, 4.5" THRU 9.875" DIAMETER HOLE (Add cost for drill steel and bit wear)

D35 0.22 25 A B 18,000 0.20 70 .700 .063 .034 10 .100 .009 .005 .530 .000 .000 0.00 0.00 0.00 0.55 ELECTRIC, OVER 9.875" DIAMETER (Add cost for drill steel and bit wear)

F10 0.00 95 A B 10,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .477 .102 .102 0.83 0.46 0.92 0.75FORK LIFTSG10 0.00 1GENERATOR SETSG10 0.10 30 A B 8,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.73 0.60 PORTABLEG10 0.10 30 S B 7,000 0.10 85 .850 .077 .041 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.20 0.70 PORTABLEG10 0.20 30 A B 10,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.00 0.70 SKID MOUNTEDG10 0.20 30 S B 8,000 0.10 85 .850 .077 .041 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.00 0.80 SKID MOUNTEDG15 0.00 35 A B 14,500 0.25 60 .600 .054 .029 0 .000 .000 .000 .000 .085 .144 0.83 0.54 0.92 0.75GRADERS, MOTORG15 0.00 35 S B 13,500 0.25 78 .780 .070 .037 0 .000 .000 .000 .000 .085 .144 0.27 0.16 0.30 0.85GRADERS, MOTOR


EP 1110-1-8, Vol. 430 Nov 11

D-7

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

11/30/2011(Vol. 1)

FACTORS

APPENDIX D

H10 0.00 95 A B 6,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 1.00HAMMERS, HYDRAULIC (Demolition tool) (Add cost for point wear)

H13 0.00 1HAZARDOUS/TOXIC WASTE EQUIPMENTH13 0.11 95 A B 10,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .530 .102 .102 1.08 0.86 1.20 0.80 COMPACTORS (Compression force) 0 THRU 50

TONSH13 0.12 95 A B 12,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .530 .102 .102 1.08 0.86 1.20 0.90 COMPACTORS (Compression force) OVER 50 TONSH13 0.21 95 A B 10,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .530 .102 .102 0.00 0.00 0.00 0.90 FILTER PRESSES, STATIONARYH13 0.22 95 A B 10,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .530 .102 .102 0.66 0.59 0.73 0.80 FILTER PRESSES, MOBILEH13 0.30 95 A B 4,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .530 .000 .000 0.00 0.00 0.00 0.70 CENTRIFUGESH13 0.40 95 A B 10,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 1.08 0.86 1.20 0.90 SHREDDERSH13 0.51 95 A B 10,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 0.77 0.69 0.86 1.00 SOIL TREATMENT PLANT, MOBILEH13 0.61 95 A B 10,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 1.00 SLUDGE PROCESSING EQUIP, SLUDGE

DISPENSERSH13 0.71 95 A B 4,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 1.00 WASTE HANDLING EQUIPMENT, DRUM HANDLINGH15 0.00 1HEATERS, SPACEH20 0.00 95 A B 9,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.00 0.80HOISTS & AIR WINCHESH25 0.00 1HYDRAULIC EXCAVATORS, CRAWLER MOUNTEDH25 0.10 65 A B 8,000 0.25 65 .650 .059 .031 0 .000 .000 .000 .000 .149 .149 0.00 0.00 0.00 0.70 0 LBS THRU 12,500 LBS (COMPACT EXCAVATORS)H25 0.10 65 S B 7,000 0.25 85 .850 .077 .041 0 .000 .000 .000 .000 .149 .149 0.00 0.00 0.00 0.80 0 LBS THRU 12,500 LBS (COMPACT EXCAVATORS)H25 0.11 65 A B 8,500 0.25 65 .650 .059 .031 0 .000 .000 .000 .000 .149 .149 0.00 0.00 0.00 0.70 OVER 12,500 LBS THRU 40,000 LBSH25 0.11 65 S B 7,000 0.25 85 .850 .077 .041 0 .000 .000 .000 .000 .149 .149 0.00 0.00 0.00 0.85 OVER 12,500 LBS THRU 40,000 LBSH25 0.12 65 A B 12,000 0.25 65 .600 .059 .031 0 .000 .000 .000 .000 .149 .149 0.00 0.00 0.00 0.80 OVER 40,000 LBS THRU 100,000 LBSH25 0.12 65 S B 10,000 0.25 85 .800 .077 .041 0 .000 .000 .000 .000 .149 .149 0.00 0.00 0.00 0.95 OVER 40,000 LBS THRU 100,000 LBS


EP 1110-1-8, Vol. 430 Nov 11

D-8

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

11/30/2011(Vol. 1)

FACTORS

APPENDIX D

H25 0.13 65 A B 16,000 0.25 65 .650 .059 .031 0 .000 .000 .000 .000 .047 .047 0.00 0.00 0.00 1.00 OVER 100,000 LBS THRU 160,000 LBSH25 0.13 65 S B 13,500 0.25 85 .850 .077 .041 0 .000 .000 .000 .000 .047 .047 0.00 0.00 0.00 1.10 OVER 100,000 LBS THRU 160,000 LBSH25 0.14 65 A B 19,000 0.25 65 .650 .059 .031 0 .000 .000 .000 .000 .051 .051 0.00 0.00 0.00 1.10 OVER 160,000 LBSH25 0.14 65 S B 15,000 0.25 85 .850 .077 .041 0 .000 .000 .000 .000 .051 .051 0.00 0.00 0.00 1.25 OVER 160,000 LBSH25 0.21 95 A B 6,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 0.90 ATTACHMENTS, MOBILE SHEARSH25 0.22 95 A B 6,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 0.80 ATTACHMENTS, MATERIAL HANDLINGH25 0.23 95 A B 6,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 1.00 ATTACHMENTS, CONCRETE PULVERIZERSH25 0.24 95 A B 6,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 1.00 ATTACHMENTS, COMPACTORSH30 0.00 1HYDRAULIC EXCAVATORS, WHEEL MOUNTEDH30 0.01 65 A B 8,000 0.25 60 .600 .054 .029 10 .100 .009 .005 .000 .149 .141 0.83 0.54 0.92 0.50 0 THRU 1.0 CYH30 0.01 65 S B 6,500 0.25 78 .780 .070 .037 13 .130 .012 .006 .000 .149 .141 0.25 0.15 0.28 0.55 0 THRU 1.0 CYH30 0.02 65 A B 10,000 0.25 60 .600 .054 .029 10 .100 .009 .005 .000 .149 .141 0.83 0.54 0.92 0.60 OVER 1.0 CYH30 0.02 65 S B 8,000 0.25 78 .780 .070 .037 13 .130 .012 .006 .000 .149 .141 0.25 0.15 0.28 0.65 OVER 1.0 CYH35 0.00 1HYDRAULIC SHOVELS, CRAWLER MOUNTEDH35 0.11 65 A B 14,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .047 .047 0.00 0.00 0.00 1.00 DIESEL, 0 CY THRU 5.0 CYH35 0.11 65 S B 12,000 0.20 85 .850 .077 .041 0 .000 .000 .000 .000 .047 .047 0.00 0.00 0.00 1.10 DIESEL, 0 CY THRU 5.0 CYH35 0.12 65 A B 16,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .051 .051 0.00 0.00 0.00 1.20 DIESEL, OVER 5.0 CYH35 0.12 65 S B 14,000 0.20 85 .850 .077 .041 0 .000 .000 .000 .000 .051 .051 0.00 0.00 0.00 1.30 DIESEL, OVER 5.0 CYH35 0.21 65 A B 18,000 0.20 50 .500 .045 .024 0 .000 .000 .000 .265 .000 .000 0.00 0.00 0.00 0.80 ELECTRIC, OVER 2.5 CYH35 0.21 65 S B 16,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .265 .000 .000 0.00 0.00 0.00 0.90 ELECTRIC, OVER 2.5 CYL10 0.00 70 A B 10,000 0.20 60 .600 .054 .029 10 .100 .009 .005 .000 .127 .110 0.83 0.54 0.92 0.90LAND CLEARING EQUIPMENTL10 0.00 70 S B 7,000 0.20 78 .780 .070 .037 13 .130 .012 .006 .000 .127 .110 0.25 0.15 0.28 1.00LAND CLEARING EQUIPMENT


EP 1110-1-8, Vol. 430 Nov 11

D-9

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

11/30/2011(Vol. 1)

FACTORS

APPENDIX D

L15 0.00 95 A B 4,000 0.15 80 .800 .072 .038 13 .130 .012 .006 .477 .102 .102 0.59 0.30 0.66 0.70LANDSCAPING EQUIPMENTL20 0.00 1LIGHTING SETS, TRAILER MOUNTEDL20 0.10 95 A B 8,000 0.20 85 .850 .077 .041 0 .000 .000 .000 .000 .102 .102 0.66 0.58 0.73 1.50 METALLIC VAPORL25 0.00 95 A B 8,000 0.20 85 .850 .077 .041 13 .130 .012 .006 .000 .102 .102 0.66 0.58 0.73 1.20LINE STRIPING EQUIPMENTL30 0.00 95 A B 10,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .477 .119 .119 0.66 0.58 0.73 1.00LOADERS, BELT (Conveyor belts) & ACCESSORIESL30 0.00 95 S B 8,000 0.20 85 .850 .077 .041 0 .000 .000 .000 .477 .119 .119 0.21 0.16 0.23 1.10LOADERS, BELT (Conveyor belts) & ACCESSORIESL35 0.00 40 A B 10,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .000 .170 .101 0.00 0.00 0.00 1.10LOADERS, FRONT END, CRAWLER TYPEL35 0.00 40 S B 8,000 0.20 91 .910 .082 .044 0 .000 .000 .000 .000 .170 .101 0.00 0.00 0.00 1.25LOADERS, FRONT END, CRAWLER TYPEL40 0.00 1LOADERS, FRONT END, WHEEL TYPEL40 0.11 45 A B 9,250 0.25 65 .650 .059 .031 0 .000 .000 .000 .000 .170 .111 0.83 0.54 0.92 0.70 ARTICULATED, 0 THRU 225 HPL40 0.11 45 S B 8,750 0.25 85 .850 .077 .041 0 .000 .000 .000 .000 .170 .111 0.25 0.15 0.28 0.80 ARTICULATED, 0 THRU 225 HPL40 0.12 45 A B 13,500 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .170 .080 0.83 0.54 0.92 0.70 ARTICULATED, OVER 225 HPL40 0.12 45 S B 12,000 0.20 85 .850 .077 .041 0 .000 .000 .000 .000 .170 .080 0.25 0.15 0.28 0.75 ARTICULATED, OVER 225 HPL40 0.20 45 A B 8,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .000 .170 .111 0.57 0.29 0.63 0.80 SKID STEERL40 0.21 45 A B 4,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .170 .170 0.00 0.00 0.00 1.00 SKID STEER ATTACHMENTSL40 0.31 45 A B 10,000 0.25 65 .650 .059 .031 0 .000 .000 .000 .000 .170 .111 0.83 0.54 0.92 0.85 TOOL CARRIER & TELESCOPIC HANDLERS, 0

THRU 225 HPL40 0.31 45 S B 9,250 0.25 85 .850 .077 .041 0 .000 .000 .000 .000 .170 .111 0.25 0.15 0.28 0.90 TOOL CARRIER & TELESCOPIC HANDLERS, 0

THRU 225 HPL40 0.32 45 A B 12,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .000 .170 .080 0.83 0.54 0.92 0.85 TOOL CARRIER & TELESCOPIC HANDLERS, OVER

225 HPL40 0.32 45 S B 10,000 0.15 85 .850 .077 .041 0 .000 .000 .000 .000 .170 .080 0.25 0.15 0.28 0.90 TOOL CARRIER & TELESCOPIC HANDLERS, OVER

225 HPL45 0.00 40 A B 8,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .000 .441 .524 0.00 0.00 0.00 1.35LOADERS / BACKHOE, CRAWLER TYPE


EP 1110-1-8, Vol. 430 Nov 11

D-10

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

11/30/2011(Vol. 1)

FACTORS

APPENDIX D

L45 0.00 40 S B 6,000 0.20 91 .910 .082 .044 0 .000 .000 .000 .000 .441 .524 0.00 0.00 0.00 1.40LOADERS / BACKHOE, CRAWLER TYPEL50 0.00 45 A B 10,000 0.25 50 .500 .045 .024 0 .000 .000 .000 .000 .441 .441 0.83 0.54 0.92 0.80LOADERS / BACKHOE, WHEEL TYPEL50 0.00 45 S B 6,000 0.25 70 .700 .063 .034 0 .000 .000 .000 .000 .441 .441 0.25 0.15 0.28 0.85LOADERS / BACKHOE, WHEEL TYPEL55 0.00 95 A B 6,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .441 .441 0.00 0.00 0.00 1.00LOADER / BACKHOE, ATTACHMENTSL60 0.00 75 A B 10,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .119 0.83 0.54 0.92 0.70LOG SKIDDERSL60 0.00 75 S B 8,000 0.15 85 .850 .077 .041 0 .000 .000 .000 .000 .102 .119 0.25 0.15 0.28 0.80LOG SKIDDERSM10 0.00 1MARINE EQUIPMENT (NON DREDGING)M10 0.11 105 A B 10,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.70 AQUATIC MAINTENANCEM10 0.12 105 A B 6,000 0.20 80 .800 .072 .038 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.60 AQUATIC MAINTENANCE ATTACHMENTSM10 0.21 105 A B 16,000 0.10 80 .800 .072 .038 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.70 HYDRAULIC CUTTERHEAD DREDGE, 8" OR

LESS,TRANSPORTABLEM10 0.22 105 A B 16,000 0.10 80 .800 .072 .038 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.80 HYDRAULIC CUTTERHEAD DREDGE,8" -

12",TRANSPORTABLEM10 0.23 105 A B 16,000 0.10 80 .800 .072 .038 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.80 HYDRAULIC AUGERHEAD DREDGE,12" OR

LESS,TRANSPORTABLEM10 0.24 105 A B 8,000 0.10 80 .800 .072 .038 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.70 HYDRAULIC FLOATING PUMPS,12" OR

LESS,TRANSPORTABLEM10 0.25 105 A B 6,000 0.15 80 .800 .072 .038 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.70 HYDRAULIC DREDGE PUMPS,12" OR

LESS,TRANSPORTABLEM10 0.26 105 A B 6,000 0.15 80 .800 .072 .038 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.60 HYDRAULIC DREDGE / PUMP ATTACHMENTSM10 0.31 20 A B 18,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .477 .102 .102 0.00 0.00 0.00 1.00 SMALL MECH DREDGES,CLAMSHELL,BARGE-MTD

TO 5 CYM10 0.31 20 S B 16,000 0.15 85 .850 .077 .041 0 .000 .000 .000 .477 .102 .102 0.00 0.00 0.00 1.05 SMALL MECH DREDGES,CLAMSHELL,BARGE-MTD

TO 5 CY


EP 1110-1-8, Vol. 430 Nov 11

D-11

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

11/30/2011(Vol. 1)

FACTORS

APPENDIX D

M10 0.32 65 A B 10,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .477 .161 .161 0.00 0.00 0.00 1.00 SMALL MECH DREDGES, AMPHIBIOUS EXCAVATORS

M10 0.32 65 S B 9,000 0.15 85 .850 .077 .041 0 .000 .000 .000 .477 .161 .161 0.00 0.00 0.00 1.10 SMALL MECH DREDGES, AMPHIBIOUS EXCAVATORS

M10 0.33 105 A B 20,000 0.15 80 .800 .072 .038 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.90 SMALL MECH DREDGES,HOE-MOUNTED DREDGING ATTACH

M10 0.41 105 A B 6,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.50 WORK FLOATS (NON-DREDGING)M10 0.42 105 A B 30,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.60 WORK BARGES (SECTIONAL, NON-DREDGING)M10 0.45 105 A B 90,000 0.05 20 .200 .018 .010 0 .000 .000 .000 .000 .000 .136 0.00 0.00 0.00 0.60 FLAT-DECK OR CARGO BARGE (NON-DREDGING)M10 0.46 105 A B 90,000 0.05 20 .200 .018 .010 0 .000 .000 .000 .000 .000 .136 0.00 0.00 0.00 0.70 DUMP SCOW (NON-DREDGING)M10 0.47 105 A B 30,000 0.05 20 .200 .018 .010 0 .000 .000 .000 .000 .000 .136 0.00 0.00 0.00 0.70 DRILL BARGE (NON-DREDGING)M10 0.48 105 A B 30,000 0.05 20 .200 .018 .010 0 .000 .000 .000 .000 .000 .136 0.00 0.00 0.00 0.70 ALL OTHER BARGES (NON-DREDGING)M10 0.51 105 A B 16,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .161 0.00 0.00 0.00 0.70 BOATS & LAUNCHES, 0 THRU 250 HPM10 0.51 105 S B 13,000 0.15 85 .850 .077 .041 0 .000 .000 .000 .477 .136 .161 0.00 0.00 0.00 0.75 BOATS & LAUNCHES, 0 THRU 250 HPM10 0.53 105 A B 18,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .161 0.00 0.00 0.00 0.80 BOATS & LAUNCHES, 251 THRU 500 HPM10 0.53 105 S B 15,000 0.10 85 .850 .077 .041 0 .000 .000 .000 .477 .136 .161 0.00 0.00 0.00 0.85 BOATS & LAUNCHES, 251 THRU 500 HPM10 0.54 105 A B 40,000 0.10 60 .600 .054 .029 50 .500 .045 .024 .477 .136 .161 0.00 0.00 0.00 0.90 TUGS, 501 THRU 1,000 HPM10 0.55 105 A B 55,000 0.10 60 .600 .054 .029 50 .500 .045 .024 .477 .136 .161 0.00 0.00 0.00 1.00 TUGS, 1,000 THRU 2,000 HPP10 0.00 50 A B 6,000 0.35 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .136 0.00 0.00 0.00 0.80PILE HAMMER ACCESSORIES - EXTRACTORS &

BOX LEADSP20 0.00 1PILE HAMMERS, DOUBLE ACTINGP20 0.10 50 A B 6,000 0.25 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 1.10 DIESELP20 0.20 50 A B 6,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 1.10 PNEUMATIC (STEAM/AIR)P25 0.00 1PILE HAMMERS, SINGLE ACTING


EP 1110-1-8, Vol. 430 Nov 11

D-12

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

11/30/2011(Vol. 1)

FACTORS

APPENDIX D

P25 0.10 50 A B 6,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 1.00 DIESELP25 0.20 50 A B 6,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 1.00 PNEUMATIC (STEAM/AIR)P30 0.00 50 A B 6,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .136 0.00 0.00 0.00 1.00PILE HAMMERS, DRIVER/ EXTRACTOR, VIBRATORYP35 0.00 70 A B 14,000 0.20 35 .350 .032 .017 0 .000 .000 .000 .000 .000 .170 0.00 0.00 0.00 0.95PIPELAYERSP35 0.00 70 S B 11,500 0.20 46 .460 .041 .022 0 .000 .000 .000 .000 .000 .170 0.00 0.00 0.00 1.10PIPELAYERSP40 0.00 20 A B 8,000 0.10 50 .500 .045 .024 50 .500 .045 .024 .477 .136 .119 0.66 0.33 0.73 0.80PLATFORMS & MAN-LIFTSP45 0.00 95 A B 8,000 0.15 95 .950 .086 .045 0 .000 .000 .000 .477 .136 .119 0.66 0.59 0.73 1.00PUMPS, GROUTP50 0.00 1PUMPS, WATER, CENTRIFUGAL, TRASHP50 0.11 95 A B 8,000 0.20 90 .900 .081 .043 0 .000 .000 .000 .000 .136 .161 0.66 0.00 0.73 0.90 ENGINE DRIVEP50 0.12 95 A B 8,000 0.20 90 .900 .081 .043 0 .000 .000 .000 .477 .000 .000 0.66 0.00 0.73 0.50 ELECTRIC DRIVEP50 0.21 95 A B 8,000 0.20 90 .900 .081 .043 0 .000 .000 .000 .000 .136 .161 0.66 0.00 0.73 0.90 WHEEL MOUNTED, ENGINE DRIVEP50 0.22 95 A B 8,000 0.20 90 .900 .081 .043 0 .000 .000 .000 .477 .000 .000 0.66 0.00 0.73 0.50 WHEEL MOUNTED, ELECTRIC DRIVEP50 0.31 95 A B 4,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 1.50 HOSES, PUMP, SUCTION & DISCHARGEP55 0.00 1PUMPS, WATER, SUBMERSIBLEP55 0.01 95 A B 8,000 0.20 90 .900 .081 .043 0 .000 .000 .000 .000 .136 .161 0.00 0.00 0.00 1.00 ENGINE DRIVEP55 0.02 95 A B 8,000 0.15 90 .900 .081 .043 0 .000 .000 .000 .477 .000 .000 0.00 0.00 0.00 0.60 ELECTRIC DRIVEP60 0.00 1PUMPS, WATER, CENTRIFUGAL, DEWATERINGP60 0.11 95 A B 8,000 0.20 90 .900 .081 .043 0 .000 .000 .000 .000 .136 .161 0.00 0.00 0.00 0.90 SKID MOUNTED, ENGINE DRIVEP60 0.12 95 A B 8,000 0.15 90 .900 .081 .043 0 .000 .000 .000 .477 .000 .000 0.00 0.00 0.00 0.50 SKID MOUNTED, ELECTRIC DRIVEP60 0.21 95 A B 8,000 0.20 90 .900 .081 .043 0 .000 .000 .000 .000 .136 .161 0.00 0.00 0.73 0.90 WHEEL MOUNTED, ENGINE DRIVEP60 0.22 95 A B 8,000 0.15 90 .900 .081 .043 0 .000 .000 .000 .477 .000 .000 0.00 0.00 0.73 0.50 WHEEL MOUNTED, ELECTRIC DRIVEP65 0.00 1PUMPS, WATER, DIAPHRAGM


EP 1110-1-8, Vol. 430 Nov 11

D-13

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

11/30/2011(Vol. 1)

FACTORS

APPENDIX D

P65 0.11 95 A B 8,000 0.20 90 .900 .081 .043 0 .000 .000 .000 .000 .136 .161 0.00 0.00 0.00 0.90 SKID MOUNTED, ENGINE DRIVEP65 0.12 95 A B 8,000 0.15 90 .900 .081 .043 0 .000 .000 .000 .477 .000 .000 0.00 0.00 0.00 0.50 SKID MOUNTED, ELECTRIC DRIVEP65 0.21 95 A B 8,000 0.20 90 .900 .081 .043 0 .000 .000 .000 .000 .136 .161 0.00 0.00 0.73 0.80 WHEEL MOUNTED, ENGINE DRIVEP65 0.22 95 A B 8,000 0.15 90 .900 .081 .043 0 .000 .000 .000 .477 .000 .000 0.00 0.00 0.73 0.40 WHEEL MOUNTED, ELECTRIC DRIVEP70 0.00 1PUMPS, WATER (For core drills)P70 0.01 95 A B 8,000 0.25 90 .900 .081 .043 0 .000 .000 .000 .000 .136 .161 0.00 0.00 0.00 0.80 ENGINE DRIVEP70 0.02 95 A B 8,000 0.25 90 .900 .081 .043 0 .000 .000 .000 .477 .000 .000 0.00 0.00 0.00 0.40 ELECTRIC DRIVER10 0.00 70 A B 8,000 0.20 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.90RIPPERS & HYDRAULIC BANK SLOPERS (Add cost

for point wear)R10 0.00 70 S B 6,500 0.20 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 1.00RIPPERS & HYDRAULIC BANK SLOPERS (Add cost

for point wear)R15 0.00 55 A B 10,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.92 0.70ROLLERS, STATIC, TOWED, PNEUMATICR20 0.00 55 A B 10,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.92 0.80ROLLERS, STATIC, TOWED, STEEL DRUMR30 0.00 1ROLLERS, STATIC, SELF-PROPELLED R30 0.01 55 A B 8,000 0.15 80 .800 .072 .038 0 .000 .000 .000 .000 .102 .102 0.83 0.54 0.92 0.70 PNEUMATICR30 0.02 55 A B 10,000 0.15 80 .800 .072 .038 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.00 0.80 SMOOTH DRUMR30 0.03 55 A B 12,000 0.20 80 .800 .072 .038 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.00 0.80 TAMPING FOOT, LANDFILL & SOIL COMPACTORSR40 0.00 55 A B 8,000 0.20 90 .900 .081 .043 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 0.80ROLLERS, VIBRATORY, TOWEDR45 0.00 55 A B 8,000 0.20 90 .900 .081 .043 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 1.10ROLLERS, VIBRATORY, SELF-PROPELLED,

DOUBLE DRUMR50 0.00 55 A B 8,000 0.25 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .136 0.83 0.54 0.92 1.00ROLLERS, VIBRATORY, SELF-PROPELLED, SINGLE

DRUMR55 0.00 95 A B 6,000 0.15 60 .600 .054 .029 0 .000 .000 .000 .477 .102 .102 0.97 0.87 1.08 0.80ROOFING EQUIPMENTS10 0.00 1SCRAPERS, ELEVATING


EP 1110-1-8, Vol. 430 Nov 11

D-14

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

11/30/2011(Vol. 1)

FACTORS

APPENDIX D

S10 0.01 60 A B 10,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .000 .170 0.84 0.55 0.93 0.90 0 THRU 200 HPS10 0.01 60 S B 8,000 0.20 85 .850 .077 .041 0 .000 .000 .000 .000 .000 .170 0.23 0.13 0.25 1.00 0 THRU 200 HPS10 0.02 60 A B 13,000 0.25 65 .650 .059 .031 0 .000 .000 .000 .000 .000 .136 0.84 0.55 0.93 0.95 OVER 200 HPS10 0.02 60 S B 11,500 0.25 85 .850 .077 .041 0 .000 .000 .000 .000 .000 .136 0.23 0.13 0.25 1.00 OVER 200 HPS15 0.00 60 A B 15,000 0.20 60 .600 .054 .029 0 .000 .000 .000 .000 .000 .136 0.84 0.55 0.93 0.80SCRAPERS, CONVENTIONALS15 0.00 60 S B 12,500 0.20 78 .780 .070 .037 0 .000 .000 .000 .000 .000 .136 0.23 0.13 0.25 0.85SCRAPERS, CONVENTIONALS20 0.00 60 A B 15,000 0.20 62 .620 .056 .030 62 .620 .056 .030 .000 .000 .110 0.84 0.55 0.93 0.85SCRAPERS, TANDEM POWEREDS20 0.00 60 S B 13,500 0.20 81 .810 .073 .039 81 .810 .073 .039 .000 .000 .110 0.23 0.13 0.25 0.90SCRAPERS, TANDEM POWEREDS25 0.00 60 A B 12,000 0.20 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.84 0.55 0.93 0.70SCRAPERS, TRACTOR DRAWNS25 0.00 60 S B 10,000 0.20 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.23 0.13 0.25 0.75SCRAPERS, TRACTOR DRAWNS30 0.00 1SCREENING & CRUSHING PLANTSS30 0.10 95 A B 10,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 1.08 0.86 1.20 0.70 CONVEYORSS30 0.10 95 S B 8,000 0.10 78 .780 .070 .037 0 .000 .000 .000 .577 .163 .142 0.96 0.72 1.07 0.85 CONVEYORSS30 0.20 95 A B 25,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 1.08 0.86 1.20 1.00 CRUSHERS - VERTICAL & HORIZONTAL SHAFT

IMPACTORS30 0.20 95 S B 15,000 0.10 78 .780 .070 .037 0 .000 .000 .000 .577 .163 .142 0.96 0.72 1.07 1.25 CRUSHERS - VERTICAL & HORIZONTAL SHAFT

IMPACTORS30 0.21 95 A B 25,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 1.08 0.86 1.20 1.20 CRUSHERS - CONES30 0.21 95 S B 15,000 0.10 78 .780 .070 .037 0 .000 .000 .000 .577 .163 .142 0.96 0.72 1.07 1.60 CRUSHERS - CONES30 0.22 95 A B 25,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 1.08 0.86 1.20 0.65 CRUSHERS - JAWS30 0.22 95 S B 15,000 0.10 78 .780 .070 .037 0 .000 .000 .000 .577 .163 .142 0.96 0.72 1.07 0.85 CRUSHERS - JAWS30 0.30 95 A B 10,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 1.08 0.86 1.20 0.80 SCREENING PLANTS30 0.30 95 S B 8,000 0.10 78 .780 .070 .037 0 .000 .000 .000 .577 .163 .142 0.96 0.72 1.07 1.00 SCREENING PLANT


EP 1110-1-8, Vol. 430 Nov 11

D-15

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

11/30/2011(Vol. 1)

FACTORS

APPENDIX D

S35 0.00 95 A B 8,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .000 .119 0.00 0.00 0.00 0.80SNOW REMOVAL EQUIPMENTS40 0.00 60 A B 10,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .000 .000 .119 0.84 0.55 0.96 0.85SOIL & ROAD STABILIZERSS40 0.00 60 S B 8,000 0.20 91 .910 .082 .044 0 .000 .000 .000 .000 .000 .119 0.23 0.13 0.25 0.95SOIL & ROAD STABILIZERSS45 0.00 95 A B 6,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 1.00SPLITTERS, ROCK & CONCRETET10 0.00 70 A B 10,000 0.20 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.96 0.80TRACTOR BLADES & ATTACHMENTS (including

agricultural)T10 0.00 70 S B 8,000 0.20 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.86 0.90TRACTOR BLADES & ATTACHMENTS (including

agricultural)T15 0.00 1TRACTORS, CRAWLER (DOZER) (includes blade)T15 0.01 70 A B 10,000 0.30 70 .700 .063 .034 0 .000 .000 .000 .000 .000 .153 0.00 0.00 0.00 1.10 0 THRU 225 HPT15 0.01 70 S B 8,000 0.30 91 .910 .082 .044 0 .000 .000 .000 .000 .000 .153 0.00 0.00 0.00 1.25 0 THRU 225 HPT15 0.02 70 A B 12,500 0.25 70 .700 .063 .034 0 .000 .000 .000 .000 .000 .119 0.00 0.00 0.00 1.20 226 HP THRU 425 HPT15 0.02 70 S B 10,500 0.25 91 .910 .082 .044 0 .000 .000 .000 .000 .000 .119 0.00 0.00 0.00 1.25 226 HP THRU 425 HPT15 0.03 70 A B 15,000 0.20 60 .600 .054 .029 0 .000 .000 .000 .000 .000 .066 0.00 0.00 0.00 1.20 OVER 425 HPT15 0.03 70 S B 12,500 0.20 78 .780 .070 .037 0 .000 .000 .000 .000 .000 .066 0.00 0.00 0.00 1.35 OVER 425 HPT20 0.00 75 A B 14,000 0.15 60 .600 .054 .029 0 .000 .000 .000 .000 .102 .119 0.96 0.63 0.00 0.60TRACTORS, WHEEL TYPE (DOZER)T20 0.00 75 S B 13,000 0.15 78 .780 .070 .037 0 .000 .000 .000 .000 .102 .119 0.25 0.15 0.00 0.65TRACTORS, WHEEL TYPE (DOZER)T25 0.00 1TRACTORS, AGRICULTURALT25 0.10 75 A B 10,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .119 0.00 0.00 0.00 0.85 CRAWLERT25 0.20 75 A B 8,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .119 0.96 0.73 0.00 0.70 WHEELT30 0.00 80 A B 8,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .119 .119 1.08 0.82 0.00 0.90TRENCHERS, CHAIN TYPE CUTTERT30 0.00 80 S B 6,000 0.20 85 .850 .077 .041 0 .000 .000 .000 .000 .119 .119 0.32 0.22 0.00 1.00TRENCHERS, CHAIN TYPE CUTTERT35 0.00 80 A B 8,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .119 .119 1.08 0.82 0.00 0.90TRENCHERS, WHEEL TYPE CUTTER


EP 1110-1-8, Vol. 430 Nov 11

D-16

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

11/30/2011(Vol. 1)

FACTORS

APPENDIX D

T35 0.00 80 S B 6,000 0.20 85 .850 .077 .041 0 .000 .000 .000 .000 .119 .119 0.32 0.22 0.00 1.00TRENCHERS, WHEEL TYPE CUTTERT40 0.00 1TRUCK OPTIONST40 0.10 95 A B 8,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .136 0.00 0.00 0.00 0.80 CRANES / HOISTS, PERSONNEL & MATERIAL

HANDLINGT40 0.20 95 A B 8,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.70 DUMP BODY, REART40 0.20 95 S B 6,500 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.80 DUMP BODY, REART40 0.30 95 A B 8,000 0.20 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.60 FLATBEDS, WITH SIDEST40 0.41 95 A B 8,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .136 0.00 0.00 0.00 0.70 HOIST, ELECTRIC DRIVET40 0.50 95 A B 8,000 0.15 65 .650 .059 .031 35 .350 .032 .017 .477 .136 .136 0.77 0.69 0.86 0.70 TRANSIT MIXERST40 0.60 95 A B 8,000 0.25 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .136 0.00 0.00 0.00 0.60 WATER TANKST40 0.70 95 A B 8,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .136 1.08 0.86 1.20 0.70 ALL OTHER OPTIONST45 0.00 1TRUCK TRAILERST45 0.10 95 A B 10,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.66 0.00 0.73 0.70 BOTTOM DUMPT45 0.10 95 S B 8,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.18 0.00 0.20 0.80 BOTTOM DUMPT45 0.20 95 A B 10,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.66 0.00 0.73 0.65 END DUMPT45 0.20 95 S B 8,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.18 0.00 0.20 0.75 END DUMPT45 0.30 95 A B 8,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.66 0.00 0.73 0.60 PUP TRAILERT45 0.41 95 A B 10,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.66 0.00 0.73 0.50 LOWBOY, RIGID NECK, DROP DECKT45 0.50 95 A B 10,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.66 0.00 0.73 0.50 FLATBED TRAILERT45 0.60 95 A B 10,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.66 0.00 0.73 0.50 MISCELLANEOUS / UTILITYT45 0.70 95 A B 10,000 0.25 65 .650 .059 .031 0 .000 .000 .000 .000 .119 .102 0.66 0.92 0.73 0.60 WATER TANKER TRAILERT45 0.80 95 A B 8,000 0.25 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.66 0.00 0.73 0.70 DECONTAMINATION FACILITYT45 0.90 95 A B 10,000 0.25 65 .650 .059 .031 0 .000 .000 .000 .000 .119 .102 0.66 0.00 0.73 0.70 TANK TRAILERS


EP 1110-1-8, Vol. 430 Nov 11

D-17

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

11/30/2011(Vol. 1)

FACTORS

APPENDIX D

T50 0.00 1TRUCKS, HIGHWAY (Add attachments as required)T50 0.01 85 A S 8,000 0.20 15 .150 .014 .007 0 .000 .000 .000 .000 .119 .102 0.61 0.56 0.67 0.70 0 THRU 10,000 GVWT50 0.01 85 S S 6,500 0.20 20 .200 .018 .010 0 .000 .000 .000 .000 .119 .102 0.20 0.16 0.22 0.75 0 THRU 10,000 GVWT50 0.02 85 A S 10,000 0.20 35 .350 .032 .017 0 .000 .000 .000 .000 .127 .110 0.72 0.66 0.79 0.65 OVER 10,000 THRU 30,000 GVW (Chassis only - Add

options)T50 0.02 85 S S 8,000 0.20 46 .460 .041 .022 0 .000 .000 .000 .000 .127 .110 0.20 0.16 0.22 0.70 OVER 10,000 THRU 30,000 GVW (Chassis only - Add

options)T50 0.03 85 A S 12,000 0.20 50 .500 .045 .024 0 .000 .000 .000 .000 .136 .119 0.77 0.71 0.86 0.65 OVER 30,000 GVW (Chassis only - Add options)T50 0.03 85 S S 10,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .119 0.21 0.18 0.24 0.75 OVER 30,000 GVW (Chassis only - Add options)T55 0.00 1TRUCKS, OFF-HIGHWAYT55 0.10 90 A B 20,000 0.15 35 .350 .032 .017 0 .000 .000 .000 .000 .000 .144 0.84 0.73 0.93 0.90 RIGID FRAMET55 0.10 90 S B 18,000 0.15 45 .450 .041 .022 0 .000 .000 .000 .000 .000 .144 0.23 0.18 0.25 0.95 RIGID FRAMET55 0.20 90 A B 13,000 0.15 50 .500 .045 .024 0 .000 .000 .000 .000 .000 .080 0.84 0.73 0.93 0.80 ARTICULATED FRAMET55 0.20 90 S B 12,250 0.15 60 .600 .054 .029 0 .000 .000 .000 .000 .000 .080 0.23 0.18 0.25 0.85 ARTICULATED FRAMET56 0.00 1TRUCKS,OFF-HIGHWAY/PRIME MOVER TRACTORS

& WAGONST56 0.10 90 A B 20,000 0.15 40 .400 .036 .019 0 .000 .000 .000 .000 .102 .144 0.84 0.64 0.93 0.90 PRIME MOVER TRACTORST56 0.10 90 S B 18,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .136 0.23 0.16 0.25 0.95 PRIME MOVER TRACTORST56 0.20 90 A B 15,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .136 0.84 0.64 0.93 0.65 WAGONS, BOTTOM DUMPT56 0.20 90 S B 10,000 0.20 85 .850 .077 .041 0 .000 .000 .000 .000 .102 .136 0.23 0.16 0.25 0.75 WAGONS, BOTTOM DUMPT56 0.30 90 A B 12,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .136 0.84 0.65 0.93 0.60 WAGONS, REAR DUMPT57 0.00 95 A B 10,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .119 0.23 0.17 0.25 0.80TRUCKS, VACUUMT60 0.00 90 A B 12,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .136 0.90 0.69 1.00 0.70TRUCKS, WATER, OFF-HIGHWAY


EP 1110-1-8, Vol. 430 Nov 11

D-18

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

11/30/2011(Vol. 1)

FACTORS

APPENDIX D

T60 0.00 90 S B 10,000 0.20 85 .850 .077 .041 0 .000 .000 .000 .000 .102 .136 0.25 0.17 0.28 0.80TRUCKS, WATER, OFF-HIGHWAYT65 0.00 1TUNNEL/MINING EQUIPMENTT65 0.10 25 A B 14,000 0.15 80 .800 .072 .038 13 .130 .012 .006 .530 .136 .119 0.67 0.57 0.00 0.90 DRIFTING & TUNNELING DRILLST65 0.20 95 A B 18,000 0.15 70 .700 .063 .034 0 .000 .000 .000 .530 .000 .000 0.00 0.00 0.00 0.70 TUNNEL BORING MACHINEST65 0.20 95 S B 16,000 0.15 91 .910 .082 .044 0 .000 .000 .000 .530 .000 .000 0.00 0.00 0.00 0.80 TUNNEL BORING MACHINEST65 0.30 25 A B 12,000 0.15 80 .800 .072 .038 0 .000 .000 .000 .530 .136 .119 0.00 0.00 0.00 0.90 PRODUCTION DRILLING RIGST65 0.40 95 A B 16,000 0.15 70 .700 .063 .034 0 .000 .000 .000 .530 .000 .000 0.00 0.00 0.00 0.90 ROADHEADERS & CONTINUOUS MINERST65 0.40 95 S B 14,000 0.15 91 .910 .082 .044 0 .000 .000 .000 .530 .000 .000 0.00 0.00 0.00 1.00 ROADHEADERS & CONTINUOUS MINERST65 0.50 95 A B 10,000 0.20 80 .800 .072 .038 10 .100 .009 .005 .530 .136 .119 0.00 0.00 0.00 0.80 ROCK BOLTING EQUIPMENTT65 0.61 95 A B 12,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .000 .136 .127 0.00 0.00 0.00 0.75 LOADING & HAULING EQUIPMENT, DIESEL OR

GAST65 0.62 95 A B 14,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .477 .102 .102 0.00 0.00 0.00 0.70 LOADING & HAULING EQUIPMENT, ELECTRICT65 0.63 95 A B 10,000 0.25 70 .700 .063 .034 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.65 LOADING & HAULING EQUIPMENT, AIR-POWEREDT65 0.70 95 A B 12,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.75 LOCOMOTIVEST65 0.90 95 A B 10,000 0.20 70 .700 .063 .034 13 .130 .012 .006 .477 .136 .127 0.00 0.00 0.00 0.80 OTHER TUNNELING EQUIPMENTW10 0.00 90 A B 12,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .136 0.88 0.67 0.98 0.65WAGONS, BOTTOM DUMPW10 0.00 90 S B 10,000 0.15 85 .850 .077 .041 0 .000 .000 .000 .000 .102 .136 0.25 0.17 0.28 0.75WAGONS, BOTTOM DUMPW15 0.00 90 A B 12,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .136 0.88 0.77 0.98 0.60WAGONS, REAR DUMPW15 0.00 90 S B 10,000 0.15 85 .850 .077 .041 0 .000 .000 .000 .000 .102 .136 0.25 0.19 0.28 0.70WAGONS, REAR DUMPW25 0.00 1WATER & CO2 BLASTERSW25 0.10 95 A B 4,000 0.20 95 .950 .086 .045 0 .000 .000 .000 .424 .102 .119 0.96 0.73 1.07 1.10 LOW PRESSURE, (< 5,000 PSI)W25 0.20 95 A B 4,000 0.20 95 .950 .086 .045 0 .000 .000 .000 .424 .102 .119 0.96 0.73 1.07 1.20 HIGH PRESSURE, (>= 5,000 PSI)W25 0.30 95 A B 4,000 0.20 95 .950 .086 .045 0 .000 .000 .000 .424 .102 .119 0.00 0.00 0.73 1.10 STEAM CLEANERS


EP 1110-1-8, Vol. 430 Nov 11

D-19

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

11/30/2011(Vol. 1)

FACTORS

APPENDIX D

W25 0.40 95 A B 6,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .530 .127 .148 0.00 0.00 0.73 1.00 CO2 BLASTERSW25 0.50 95 A B 10,000 0.35 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.73 0.40 WET ABRASIVE BLASTING SYSTEM (TORBO)W30 0.00 1WATER TANKSW30 0.10 90 A B 12,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .119 0.00 0.00 0.73 0.60 PORTABLE WITH WHEELSW30 0.20 90 A B 12,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .119 0.00 0.00 0.00 0.50 SKID MOUNTEDW35 0.00 1WELDERSW35 0.10 95 A B 8,000 0.25 80 .800 .072 .038 0 .000 .000 .000 .000 .102 .102 0.00 0.00 1.07 0.75 ENGINE DRIVENW35 0.20 95 A B 6,000 0.20 30 .300 .027 .014 0 .000 .000 .000 .424 .000 .000 0.00 0.00 0.00 0.50 ELECTRIC DRIVEN


EP 1110-1-8, Vol. 430 Nov 11

D-20

APPENDIX E ECONOMIC INDEXES FOR CONSTRUCTION EQUIPMENT

EP 1110-1-8, Vol. 430 Nov 11

E-1

1997 1996 19952012 2011 2010 2009 2008 2007 2006 2005 2004 2003 2002 2001 2000 1999 1998

KEY

EQUIPMENT DIVISIONS

ECONOMIC INDEXES FOR CONSTRUCTION EQUIPMENT

(EK)

Note: Table 2-1 Equipment Rates are based on equipment purchased new in the year 2008

2013

{--Projected---------}

EP 1110-1-8

6/30/2011

APPENDIX E

(Vol. 8)

2824 260227865 Air Equipment 2585 2458 2319 2234 2157 2085 2075 2069 2079 2047 2078 2074 2070 2063 20532867

4641 4528457810 Asphalt & Concrete Paving Equipment 4526 4381 4228 4116 3950 3758 3763 3769 3766 3717 3638 3589 3490 3390 33234711

9196 8860907215 Buckets 8911 8687 8604 8502 8057 7626 7443 7254 6804 6900 6982 6930 6888 6774 66729336

7077 6818698220 Cranes, Draglines & Clamshells - Crawler & Truck Mtd 6858 6685 6621 6543 6201 5869 5728 5582 5236 5310 5289 5225 5116 5013 48807185

6177 5979609425 Drills 5938 5783 5448 5104 4762 4444 4192 4116 3819 3736 3683 3626 3574 3518 33946271

6204 5906612130 Generators 5794 5628 5357 5112 4888 4641 4566 4548 4548 4529 4520 4517 4484 4511 44576298

7844 7632773835 Graders, Motor 7516 7155 6909 6825 6578 6318 6117 6049 5979 5952 5853 5682 5544 5466 51867963

7716 7434761240 Loaders, Track 7454 7254 7037 6907 6653 6347 6177 6081 6058 6032 5960 5792 5686 5606 54347833

7120 6861702545 Loaders, Wheel 6880 6695 6494 6374 6140 5857 5701 5612 5591 5567 5511 5409 5303 5251 51017229

6821 6582672950 Pile Driving Equipment 6569 6375 6176 6033 5787 5450 5270 5195 5127 5112 5062 4993 4892 4809 47006924

7199 6983710255 Rollers 6938 6736 6424 6145 5872 5646 5406 5285 5225 5130 5204 5092 5001 4950 48517308

7844 7632773860 Scrapers & Soil Stabilizers 7516 7155 6909 6825 6578 6318 6117 6049 5979 5952 5853 5682 5544 5466 51867963

7077 6818698265 Shovels, Backhoes & Hydraulic Excavators 6858 6685 6621 6543 6201 5869 5728 5582 5236 5310 5289 5225 5116 5013 48807185

7716 7434761270 Tractors, Crawlers & Attachments 7454 7254 7037 6907 6653 6347 6177 6081 6058 6032 5960 5792 5686 5606 54347833

6884 6678679275 Tractor, Wheel 6636 6442 6144 5876 5616 5400 5170 5055 4997 4906 4833 4695 4624 4540 45276989

8886 8619876780 Trenchers 8565 8314 7930 7584 7248 6970 6466 6524 6450 6332 6223 6042 5833 5749 56709021

5657 5483558185 Trucks, Highway 5366 5123 4965 4820 4638 4450 4356 4306 4216 4212 4307 4216 4241 4318 42935743

8012 7822790590 Trucks & Wagons - Off-Highway 7785 7651 7392 7231 6896 6424 6095 6026 5931 5828 5715 5651 5581 5440 52658134

6821 6582672995 All Other Equipment 6569 6375 6176 6033 5787 5450 5270 5195 5127 5112 5062 4993 4892 4809 47006924

3786 35263735100 All Tires & Tubes 3343 3267 3025 2926 2759 2614 2487 2430 2401 2373 2371 2400 2431 2475 25593844

8214 79458103105 Marine Equipment 7773 7466 7202 6905 6661 6436 6101 5846 5771 5645 5556 5513 5429 5245 50368339

EK = Economic Key E-1

EP 1110-1-8, Vol. 430 Nov 11

E-2

1979 1978 19771994 1993 1992 1991 1990 1989 1988 1987 1986 1985 1984 1983 1982 1981 1980

KEY

EQUIPMENT DIVISIONS

ECONOMIC INDEXES FOR CONSTRUCTION EQUIPMENT

(EK)

Note: Table 2-1 Equipment Rates are based on equipment purchased new in the year 2008

EP 1110-1-8

6/30/2011(Vol. 8)

APPENDIX E

2012 200820225 Air Equipment 1963 1956 1888 1801 1730 1720 1733 1683 1695 1668 1563 1630 1521 1354 1295

3248 3092318910 Asphalt & Concrete Paving Equipment 3106 2967 2867 2793 2730 2687 2687 2611 2583 2620 2461 2296 2111 1941 1815

6638 6380666315 Buckets 5901 5640 5314 4872 4767 4713 4640 4527 4471 4541 4313 3879 3280 2963 2738

4783 4540473620 Cranes, Draglines & Clamshells - Crawler & Truck Mtd 4298 4152 3967 3688 3595 3485 3395 3339 3282 3213 3009 2782 2512 2301 2138

3320 3196326825 Drills 3163 3069 2969 2807 2792 2786 2832 2803 2836 2810 2602 2265 1993 1858 1699

4343 4234429430 Generators 4181 4116 3998 3773 3575 3514 3510 3400 3314 3236 3160 2817 2390 2301 2128

5088 4655494635 Graders, Motor 4509 4359 4219 4010 3914 3759 3738 3645 3643 3561 3276 2992 2687 2492 2259

5257 4816506840 Loaders, Track 4677 4555 4404 4163 3918 3770 3767 3791 3792 3655 3349 3061 2750 2482 2247

4988 4758489445 Loaders, Wheel 4640 4532 4409 4235 4099 3991 3973 3944 3873 3788 3441 2938 2606 2375 2156

4598 4427453950 Pile Driving Equipment 4305 4182 4029 3845 3745 3668 3626 3570 3519 3439 3208 2894 2562 2329 2135

4719 4460448455 Rollers 4668 4630 4507 4412 4217 4151 4090 3926 3744 3431 3199 2913 2653 2396 2139

5088 4655494660 Scrapers & Soil Stabilizers 4509 4359 4219 4010 3914 3759 3738 3645 3643 3561 3276 2992 2687 2492 2259

4783 4540473665 Shovels, Backhoes & Hydraulic Excavators 4298 4152 3967 3688 3595 3485 3395 3339 3282 3213 3009 2782 2512 2301 2138

5257 4816506870 Tractors, Crawlers & Attachments 4677 4555 4404 4163 3918 3770 3767 3791 3792 3655 3349 3061 2750 2482 2247

4484 4270434275 Tractor, Wheel 4186 4123 4018 3936 3862 3820 3818 3656 3557 3530 3256 2927 2578 2319 2125

5509 5015520780 Trenchers 4948 4886 4753 4679 4600 4586 4488 4431 4360 4097 3618 3153 2772 2580 2300

4190 3838402585 Trucks, Highway 3669 3546 3495 3363 3299 3282 3139 3055 2934 2824 2638 2324 2108 1934 1775

4979 4797483790 Trucks & Wagons - Off-Highway 4739 4617 4405 4094 3915 3840 3822 3786 3744 3662 3363 2964 2588 2364 2196

4598 4427453995 All Other Equipment 4305 4182 4029 3845 3745 3668 3626 3570 3519 3439 3208 2894 2562 2329 2135

2517 25242525100 All Tires & Tubes 2506 2470 2480 2399 2322 2340 2374 2421 2453 2552 2506 2369 2055 1792 1699

4951 46794881105 Marine Equipment 4438 4271 4091 3920 3886 3863 3749 3633 3497 3391 3239 2922 2587 2352 2156

EK = Economic Key E-2

EP 1110-1-8, Vol. 430 Nov 11

E-3


EP 1110-1-8, Vol. 430 Nov 11

E-4

APPENDIX F TIRE DESCRIPTION AND TIRE COST

EP 1110-1-8, Vol. 430 Nov 11

F-1

EP CODE SIZE DESCRIPTION SIZE PER EACHCOSTTUBE

PLY (1)

TIRE DESCRIPTION AND TIRE COST

EP 1110-1-8(Vol. 8)

11/30/2011

INDUSTRY CODE

APPENDIX F

LT TRUCK/RECREATIONAL VEHICLE, RADIAL

(Life =WORKHORSE EXTRA GRIP RADIAL 5000 hrs )

ABAA3 LT265/75R16 10.40 16.00 TL $206x 10

(Life =WRANGLER RADIAL AT 5000 hrs )

ABAC1 LT235/75R15 9.25 15.00 TL $158x 6ABAC2 31-1050R15 10.50 15.00 TL $143x 6

(Life =SERVICE TRAILER - MARATHON RADIAL 5000 hrs )

ABBF1 ST175/80R13 7.00 13.00 TL $82x 4ABBF3 ST185/80R13 7.20 13.00 TL $94x 6ABBF5 ST205/75R14 8.00 14.00 TL $108x 6ABBF8 ST205/75R15 8.00 15.00 TL $127x 6ABBF6 ST215/75R14 8.50 14.00 TL $114x 6ABBF9 ST225/75R15 8.80 15.00 TL $128x 6ABBF10 ST225/75R15 8.80 15.00 TL $141x 8

LT TRUCK/RECREATIONAL VEHICLE, BIAS

(Life =WORKHORSE RIB 5000 hrs )

ACBA2 700-15LT 8.30 15.00 TL $182x 8ACBA7 875-16.5LT 8.80 16.50 TL $214x 10ACBA4 750-16LT 8.90 16.00 TL $210x 10ACBA9 950-16.5LT 9.60 16.50 TL $235x 10

(Life =TRACTION HI-MILER 5000 hrs )

ACBC1 6.70-15LT 7.50 15.00 TL $180x 6ACBC3 8-14.5LT 8.00 14.50 TL $137x 12ACBC4 9-14.5LT 9.50 14.50 TL $158x 12

(Life =CUSTOM HI-MILER 5000 hrs )

ACBD1 12-16.5LT 12.10 16.50 TL $764x 12

OVER-THE-ROAD TRUCK, COMMERCIAL, RADIAL

(Life =COMMERICAL RADIAL LT TRUCK 5000 hrs )

ADCA2 LT225/75R16 7.50 16.00 TL $260x 10ADCA17 8R19.5 8.00 19.50 TL $428x 10ADCA18 8R195 8.00 19.50 TL $280x 12

F-1(1) TT = includes tube, TL = no tube, NO = no tube

EP 1110-1-8, Vol. 430 Nov 11

F-2


PLY (1)


EP 1110-1-8(Vol. 8)11/30/2011

INDUSTRY CODE

APPENDIX F

ADCA4 LT215/85R16 8.50 16.00 TL $193x 10ADCA3 LT215/85R16 8.50 16.00 TL $204x 8ADCA1 750R16LT 8.70 16.00 TL $176x 8ADCA6 LT225/75R16 8.80 16.00 TL $149x 10ADCA19 225/70R195 8.85 19.50 TL $318x 12ADCA8 LT235/85R16 9.25 16.00 TL $149x 10ADCA21 245/70R195 9.65 19.50 TL $401x 14ADCA11 LT245/75R16 9.80 16.00 TL $166x 10

(Life =COMMERCIAL RADIAL TRUCK TL 5000 hrs )

ADCB2 9R175 9.00 17.50 TL $337x 16ADCB5 9R22.5 9.00 22.50 TL $300x 12ADCB3 10R175 10.00 17.50 TL $338x 16ADCB7 10R22.5 10.00 22.50 TL $429x 14ADCB4 11R17.5 11.00 17.50 TL $414x 16ADCB8 11R22.5 11.00 22.50 TL $572x 16ADCB13 11R24.5 11.00 24.50 TL $618x 16ADCB10 12R22.5 12.00 22.50 TL $670x 16ADCB14 12R24.5 12.00 24.50 TL $689x 16

(Life =LOW PROFILE RADIAL TRUCK TL 5000 hrs )

ADCC1 215/75R175 8.40 17.50 TL $303x 16ADCC5 245/75R22.5 9.60 22.50 TL $328x 14ADCC3 255/70R22.5 10.00 22.50 TL $397x 16ADCC2 265/70R19.5 10.40 19.50 TL $348x 14ADCC6 265/75R22.5 10.40 22.50 TL $399x 14ADCC4 275/70R22.5 10.80 22.50 TL $462x 16ADCC12 285/75R24.5 11.20 24.50 TL $611x 14ADCC8 295/75R22.5 11.60 22.50 TL $586x 16ADCC10 315/80R22.5 12.40 22.50 TL $668x 18

(Life =SUPER SINGLE COMMERCIAL RADIAL TRUCK 5000 hrs )

ADCD1 385/65R22.5 15.10 22.50 TL $769x 18ADCD2 425/65R22.5 16.70 22.50 TL $864x 20ADCD3 445/65R22.5 17.50 22.50 TL $977x 20

(Life =COMMERCIAL RADIAL TRUCK TT 5000 hrs )

ADCE1 825R15 8.25 15.00 TT $319x 14ADCE5 9.00R20 8.25 20.00 TT $419x 12


EP 1110-1-8, Vol. 430 Nov 11

F-3


PLY (1)


EP 1110-1-8(Vol. 8)

11/30/2011

INDUSTRY CODE

APPENDIX F

ADCE6 9.00R20 9.00 20.00 TT $439x 12ADCE3 1000R15 10.00 15.00 TT $463x 14ADCE7 1000R20 10.00 20.00 TT $496x 14ADCE13 10R22.5 10.00 22.50 TL $495x 12ADCE12 365/80R20 10.40 20.00 TT $708x 18ADCE9 1100R20 11.00 20.00 TT $577x 16ADCE10 1100R20 11.00 20.00 TT $658x 16ADCE14 1100R22 11.00 22.00 TT $683x 16ADCE15 1100R24 11.00 24.00 TT $684x 16ADCE11 1200R20 12.00 20.00 TT $703x 18ADCE17 1200R24 12.00 24.00 TT $754x 18

FARM, FRONT

(Life =DYNA RIB F-2-M 5000 hrs )

AFED2 1000-16 10.00 16.00 TL $398x 8F-2MAFED1 11L-15 11.00 15.00 TL $373x 6F-2MAFED4 1100-16 11.00 16.00 TL $455x 8F-2MAFED8 1100-24 11.00 24.00 TL $879x 12F-2MAFED6 14L-161 14.00 16.10 TL $799x 10F-2MAFED7 165L-161 16.50 16.10 TL $1,007x 8F-2M

(Life =SINGLE RIB FRONT TRACTOR F-1 5000 hrs )

AFEE1 600-16 6.00 16.00 TT $227x 4F-1

(Life =FARM HIGHWAY SERVICE 5000 hrs )

AFEF2 95L-15FI 9.50 15.00 TL $302x DI-1AFEF5 11L-15FI 11.00 15.00 TL $395x FI-1AFEF7 125L-15FI 12.50 15.00 TL $546x FI-1

(Life =FARM UTILITY 5000 hrs )

AFEG7 750-14 7.50 14.00 TL $211x 4I-1AFEG14 760-15 7.60 15.00 TL $236x 8I-1AFEG8 85L-14 8.50 14.00 TL $218x 6I-1AFEG1 95L-14 9.50 14.00 TT $257x 6I-1AFEG17 95L-15 9.50 15.00 TL $311x 12I-1AFEG18 1000-15 10.00 15.00 TL $322x 8I-1AFEG11 11L-14 11.00 14.00 TL $244x 8I-1AFEG22 11L-15 11.00 15.00 TL $288x 10I-1


EP 1110-1-8, Vol. 430 Nov 11

F-4


PLY (1)


EP 1110-1-8(Vol. 8)11/30/2011

INDUSTRY CODE

APPENDIX F

AFEG20 11L-15 11.00 15.00 TL $239x 8I-1AFEG34 11L-16 11.00 16.00 TL $251x 10I-1AFEG25 125L-15 12.50 15.00 TL $369x 12I-1AFEG30 125L-16 12.50 16.00 TL $439x 12I-1AFEG29 125L-16 12.50 16.00 TL $381x 8I-1AFEG28 14L-161 14.00 16.10 TL $615x 12I-1AFEG31 165L-161 16.50 16.10 TL $721x 10I-1AFEG32 19L-161 19.00 16.10 TL $805x 10I-1AFEG27 215L-161 21.50 16.10 TL $1,338x 14I-1

(Life =FOUR RIB FRONT TRACTOR F-2-M 5000 hrs )

AFEH1 750-16 7.50 16.00 TT $302x 6F-2MAFEH3 1000-16 10.00 16.00 TT $352x 8F-2MAFEH4 1100-16 11.00 16.00 TT $411x 8F-2M

(Life =IMPLEMENT RIB 5000 hrs )

FFEK11 4.00-18 4.00 18.00 TT $156x 4I-1AFEK4 500-15 5.00 15.00 TL $171x 4I-1AFEK16 590-15 5.90 15.00 TL $152x 4I-1AFEK6 600-16 6.00 16.00 TL $193x 6I-1AFEK7 650-16 6.50 16.00 TL $186x 6I-1AFEK5 670-15 6.70 15.00 TL $177x 6I-1AFEK9 750-16 7.50 16.00 TL $260x 10I-1AFEK10 900-16 9.00 16.00 TL $357x 10I-1AFEK13 900-24 9.00 24.00 TL $565x 8I-1AFEK14 1125-28 11.25 28.00 TL $1,211x 12I-1

(Life =LABORER F-3 5000 hrs )

AFEL6 145/75-161 5.70 16.10 TL $854x 10F-3AFEL2 11L-15 11.00 15.00 TL $350x 10F-3AFEL4 11L-16 11.00 16.00 TL $362x 10F-3AFEL5 11L-16 11.00 16.00 TL $417x 12F-3

(Life =MULTI-RIB F-3 5000 hrs )

AFEM1 900-10 9.00 10.00 TT $213x 10F-3TFEM2 1100-16 11.00 16.00 TL $503x 12F-3

(Life =SMOOTH 5000 hrs )

AFEN1 169-30 16.90 30.00 TL $2,193x 6I-1


EP 1110-1-8, Vol. 430 Nov 11

F-5


PLY (1)


EP 1110-1-8(Vol. 8)

11/30/2011

INDUSTRY CODE

APPENDIX F

(Life =SMOOTH IMP 5000 hrs )

AFEO1 4.00-8 4.00 8.00 TL $113x 4AFEO3 600-16 6.00 16.00 TL $356x 10AFEO2 11L-15 11.00 15.00 TL $335x 10

(Life =SOFTRAC II 5000 hrs )

AFEP1 165L-161 16.50 16.10 TL $934x 6I-2AFEP3 215L-161 21.50 16.10 TL $1,843x 10I-2

(Life =SUPER RIB F-2 5000 hrs )

TFER1 400-12 4.00 12.00 TT $114x 4F-2

(Life =COMPACT UTILITY R-1 5000 hrs )

TFES2 5-12 5.00 12.00 TL $122x 4AFES1 7-16 7.00 16.00 TL $250x 6

(Life =SURE GRIP IMPLEMENT 5000 hrs )

AFET1 105/80-18 10.50 18.00 TL $652x 10I-3AFET2 12.5/80-18 12.50 18.00 TL $692x 10I-3

(Life =SURE GRIP LUG 5000 hrs )

AFEU2 105/80-18 10.50 18.00 TL $921x 10I-3AFEU1 124-16 12.40 16.00 TL $795x 4I-3AFEU3 12.5/80-18 12.50 18.00 TL $860x 14I-3

(Life =SURE GRIP TRACTION 5000 hrs )

AFEV1 670-15 6.70 15.00 TT $202x 4I-3AFEV5 750-16 7.50 16.00 TL $308x 4I-3AFEV2 750-18 7.50 18.00 TT $308x 4I-3AFEV3 750-20 7.50 20.00 TT $349x 4I-3AFEV4 760-15 7.60 15.00 TL $268x 6I-3

(Life =TRACTION IMPLEMENT 5000 hrs )

AFEW1 500-15 5.00 15.00 TL $195x 4I-3AFEW2 590-15 5.90 15.00 TL $209x 4I-3

(Life =TRIPLE RIB HD 5000 hrs )

AFEX8 550-16 5.50 16.00 TT $167x 6F-2AFEX10 600-16 6.00 16.00 TT $162x 6F-2AFEX11 650-16 6.50 16.00 TT $169x 6F-2


EP 1110-1-8, Vol. 430 Nov 11

F-6


PLY (1)


EP 1110-1-8(Vol. 8)11/30/2011

INDUSTRY CODE

APPENDIX F

AFEX4 75L-15 7.50 15.00 TT $188x 6F-2AFEX18 750-16 7.50 16.00 TL $223x 6F-2AFEX13 750-16 7.50 16.00 TT $225x 8F-2AFEX14 750-18 7.50 18.00 TT $239x 6F-2AFEX5 95L-15 9.50 15.00 TT $293x 8F-2AFEX16 1000-16 10.00 16.00 TL $377x 8F-2AFEX6 11L-15 11.00 15.00 TT $331x 8F-2AFEX17 1100-16 11.00 16.00 TL $473x 8F-2

(Life =TRIPLE RIB R/S F-2 5000 hrs )

AFEY2 400-15 4.00 15.00 TT $148x 4F-2AFEY1 500-15 5.00 15.00 TT $152x 4F-2

(Life =DURATORQUE R-1 5000 hrs )

AFFU3 8-16 8.00 16.00 TL $306x 6R-1

FARM, REAR

(Life =ALL TRACTION R-3 5000 hrs )

AGFA1 750-16 7.50 16.00 TT $357x 4R-3

(Life =ALL WEATHER R-3 5000 hrs )

AGFB2 95-24 9.50 24.00 TT $767x 4R-3AGFB7 136-161 13.60 16.10 TL $902x 8R-3AGFB5 136-28 13.60 28.00 TT $982x 6R-3AGFB3 149-24 14.90 24.00 TL $986x 6R-3AGFB4 169-24 16.90 24.00 TL $1,139x 6R-3AGFB8 184-161 18.40 16.10 TL $1,285x 8R-3AGFB10 184-26 18.40 26.00 TL $1,864x 12R-3AGFB11 231-26 23.10 26.00 TL $2,640x 10R-3AGFB12 231-26 23.10 26.00 TL $2,943x 12R-3AGFB14 245-32 24.50 32.00 TL $4,136x 12R-3AGFB13 28L-26 28.00 26.00 TL $3,926x 16R-3AGFB15 305L-32 30.50 32.00 TL $4,509x 12R-3AGFB16 305L-32 VA 30.50 32.00 TL $9,669x 16R-3

(Life =DT 800 RADIAL R-1W 5000 hrs )

AGFE1 320/90R42 12.60 42.00 TL $2,201x 139A8R-1WAGFE3 320/90R50 12.60 50.00 TL $2,779x 148A8R-1W


EP 1110-1-8, Vol. 430 Nov 11

F-7


PLY (1)


EP 1110-1-8(Vol. 8)

11/30/2011

INDUSTRY CODE

APPENDIX F

AGFE2 380/90R46 14.90 46.00 TL $3,125x 149A8R-1W


AGFF1 380/70R24 14.90 24.00 TL $2,346x 125A8R-1WAGFF2 420/70R28 16.50 28.00 TL $2,346x 133A8R-1WAGFF3 480/70R30 18.90 30.00 TL $2,663x 152A8R-1W


AGFG2 600/65R28 23.60 28.00 TL $3,613x 154A8/BR-1WAGFG1 620/75R26 24.40 26.00 TL $5,852x 166A8R-1WAGFG5 620/70R42 24.40 42.00 TL $4,693x UKR-1WAGFG3 650/75R34 25.60 34.00 TL $5,823x UKR-1WAGFG4 710/70R38 27.90 38.00 TL $5,016x UKR-1W

(Life =DYNA TORQUE RADIAL R-1 5000 hrs )

TGFH5 320/85R34 12.60 34.00 TL $2,073x 132DR-1AGFH7 380/85R30 14.90 30.00 TL $2,017x X3R-1AGFH9 380/85R34 14.90 34.00 TL $2,106x X3R-1AGFH15 380/85R46 14.90 46.00 TL $2,496x X3R-1TGFH6 385/85R34 15.20 34.00 TL $2,312x 141GR-1AGFH16 420/80R46 16.50 46.00 TL $3,672x UKR-1AGFH8 420/90R30 16.90 30.00 TT $2,207x X3R-1TGFH2 480/85R26 18.40 26.00 TL $2,276x X2R-1AGFH10 480/80R38 18.40 38.00 TL $2,217x 14R-1AGFH13 480/80R42 18.40 42.00 TL $2,715x X2R-1AGFH17 480/80R46 18.40 46.00 TL $3,247x X3R-1AGFH12 520/85R38 20.80 38.00 TL $2,694x 14R-1AGFH14 520/85R42 20.80 42.00 TL $2,958x 14R-1

(Life =DYNA TORQUE II R-1 5000 hrs )

AGFJ29 112-16 11.20 16.00 TL $472x 4R-1AGFJ6 136-24 13.60 24.00 TT $1,062x 8R-1AGFJ41 136-28 13.60 28.00 TL $1,093x 10R-1AGFJ11 136-28 13.60 28.00 TL $1,180x 10R-1AGFJ7 149-24 14.90 24.00 TL $872x 6R-1AGFJ31 149-24 14.90 24.00 TL $929x 8R-1AGFJ42 149-28 14.90 28.00 TL $1,504x 10R-1AGFJ8 169-24 16.90 24.00 TT $1,030x 6R-1AGFJ39 169-26 16.90 26.00 TL $1,863x 10R-1


EP 1110-1-8, Vol. 430 Nov 11

F-8


PLY (1)


EP 1110-1-8(Vol. 8)11/30/2011

INDUSTRY CODE

APPENDIX F

AGFJ43 169-28 16.90 28.00 TL $1,882x 10R-1AGFJ37 169-34 16.90 34.00 TT $1,279x 6R-1AGFJ23 169-38 16.90 38.00 TL $2,457x 14R-1AGFJ40 184-26 18.40 26.00 TL $1,787x 12R-1AGFJ18 184-34 18.40 34.00 TT $1,468x 8R-1AGFJ24 184-38 18.40 38.00 TT $1,572x 8R-1AGFJ19 208-34 20.80 34.00 TT $2,286x 8R-1AGFJ25 208-38 20.80 38.00 TT $1,981x 8R-1AGFJ27 208-42 20.80 42.00 TL $2,865x 10R-1AGFJ45 231-26 23.10 26.00 TL $2,942x 12R-1AGFJ20 231-34 23.10 34.00 TT $2,774x 8R-1AGFJ35 245-32 24.50 32.00 TL $3,193x 12R-1AGFJ34 28L-26 28.00 26.00 TL $3,847x 12R-1AGFJ36 305L-32 30.50 32.00 TL $4,614x 14R-1

(Life =INDUSTRIAL SURE GRIP R-4 5000 hrs )

AGFK1 169-30 16.90 30.00 TT $2,591x 10R-4AGFK3 184-28 18.40 28.00 TL $1,712x 12R-4

(Life =IT510 RADIAL R4 5000 hrs )

AGFL3 195LR24 19.50 24.00 TL $2,335x UKR-4

(Life =IT525 RADIAL R4 5000 hrs )

AGFM1 149-24 14.90 24.00 TL $908x 8R-4AGFM4 169-24 16.90 24.00 TL $1,147x 10R-4AGFM12 169-28 16.90 28.00 TL $1,321x 10R-4AGFM6 175L-24 17.50 24.00 TL $1,000x 10R-4AGFM5 184-24 18.40 24.00 TL $1,372x 12R-4AGFM7 195L-24 19.50 24.00 TL $1,236x 10R-4AGFM8 195L-24 19.50 24.00 TL $1,388x 12R-4AGFM9 21L-24 21.00 24.00 TL $1,835x 12R-4AGFM11 21L-24 21.00 24.00 TL $1,932x 16R-4AGFM14 21L-28 21.00 28.00 TL $2,293x 14R-4

(Life =POWER TORQUE R-1 5000 hrs )

AGFN1 6-12 6.00 12.00 TL $167x 4R-1

(Life =SPECIAL SURE GRIP R-2-0 5000 hrs )

AGFO2 149-24 14.90 24.00 TL $1,842x 6R-2


EP 1110-1-8, Vol. 430 Nov 11

F-9


PLY (1)


EP 1110-1-8(Vol. 8)

11/30/2011

INDUSTRY CODE

APPENDIX F

AGFO11 184-26 18.40 26.00 TL $1,851x 10R-2AGFO8 184-38 18.40 38.00 TL $2,543x 8R-2AGFO12 VA500/95D32 19.70 32.00 TL $5,192x 20R-2AGFO10 208-38 20.80 38.00 TL $2,690x 8R-2AGFO3 231-26 23.10 26.00 TL $2,966x 10R-2AGFO4 28L-26 28.00 26.00 TL $4,129x 12R-2AGFO6 305L-32 30.50 32.00 TL $5,753x 14R-2

(Life =SPECIAL SURE GRIP RADIAL R-2-0 5000 hrs )

AGFP8 320/90R46 12.60 46.00 TL $2,597xR-2AGFP9 340/85R46 13.40 46.00 TL $2,807x UKR-2AGFP1 169R28 16.90 28.00 TL $2,680x X2R-2AGFP2 169R30 16.90 30.00 TL $2,933x X3R-2AGFP3 184R38 18.40 38.00 TL $2,937x X1R-2AGFP5 184R42 18.40 42.00 TL $3,479x X2R-2AGFP7 184R46 18.40 46.00 TL $3,864x X3R-2AGFP4 208R38 20.80 38.00 TL $3,622x X2R-2AGFP6 520/85R42 20.80 42.00 TL $4,426x X2R-2

(Life =SUPER TRACTION RADIAL R-1W 5000 hrs )

AGFQ3 260/80R20 10.20 20.00 TL $1,107x 8R-1WAGFQ2 112R20 11.20 20.00 TL $1,111x UKR-1WAGFQ6 136R28 13.60 28.00 TL $2,143x UKR-1WFGFQ15 340/85R28 13.60 38.00 TL $635x UKR-1WAGFQ20 149R24 14.90 24.00 TL $2,613x X2R-1WFGFQ7 380/85R28 14.90 28.00 TL $1,148x UKR-1WAGFQ9 149R30 14.90 30.00 TL $2,158x UKR-1WAGFQ4 169R24 16.90 24.00 TL $3,155x UKR-1WAGFQ5 169R26 16.90 26.00 TL $3,218x UKR-1WAGFQ8 169R28 16.90 28.00 TL $2,315x UKR-1WAGFQ10 169R30 16.90 30.00 TL $2,461x UKR-1WAGFQ21 169R34 16.90 34.00 TL $3,160x X2R-1WAGFQ22 169R38 16.90 38.00 TT $3,317x X2R-1WAGFQ12 460/85R30 18.40 30.00 TL $3,842x UKR-1WAGFQ14 460/85R34 18.40 34.00 TL $3,713x UKR-1WAGFQ16 184R38 18.40 38.00 TL $2,510x UKR-1WAGFQ18 184R42 18.40 42.00 TL $3,310x UKR-1WAGFQ17 208R38 20.80 38.00 TL $3,502x UKR-1W


EP 1110-1-8, Vol. 430 Nov 11

F-10


PLY (1)


EP 1110-1-8(Vol. 8)11/30/2011

INDUSTRY CODE

APPENDIX F

AGFQ19 520/85R42 20.80 42.00 TL $3,652x UKR-1WAGFQ13 800/65R32 31.50 32.00 TL $5,602x UKR-1W

(Life =DURATORQUE R-1 5000 hrs )

AGFU1 149-28 14.90 28.00 TT $795x 6R-1AGFU2 169-30 16.90 30.00 TT $1,072x 6R-1AGFU3 184-30 18.40 30.00 TT $1,211x 6R-1AGFU5 184-38 18.40 38.00 TT $1,473x 8R-1

FARM, TERRA - 20" UP

(Life =SFT105 5000 hrs )

AHGA2 54-3100-26 31.00 26.00 TL $2,183x 10HF-1

(Life =SOF TRAC 5000 hrs )

AHGB3 38-1400-20 14.00 20.00 TL $649x 4HF-1AHGB2 41-1400-20 14.00 20.00 TL $695x 4HF-1AHGB1 44-1800-20 18.00 20.00 TL $969x 4HF-1

(Life =SUPER TERRA GRIP 5000 hrs )

AHGC1 38-1400-20 14.00 20.00 TL $949x 8HF-2AHGC2 42-2500-20 25.00 20.00 TL $2,256x 8HF-2AHGC7 54-3100-26 31.00 26.00 TL $8,387x 10HF-2AHGC11 1000/50R25 43.00 25.00 TL $8,786x 20HF-2

(Life =SUPER TERRA GRIP XT 5000 hrs )

AHGD1 42x25.00-20 25.00 20.00 TL $2,256x 8HF-2AHGD5 48-3100-20 31.00 20.00 TL $6,078x 12HF-3AHGD6 1000/50R25 43.00 25.00 TL $10,382x 10HF-3AHGD7 1050/50R32 44.00 32.00 TL $13,003x 16HF-3

(Life =CUSTOM FLO GRIP 5000 hrs )

AHGE12 67-3400-25 34.00 25.00 TL $14,923x 10HF-4

(Life =TUNDRA GRIP 5000 hrs )

AHGF2 1050/50R25 44.00 25.00 TL $10,910x 16HF-1AHGF1 66-4400-25 44.00 25.00 TL $10,474x 20HF-1

FARM, SPECIALTY


EP 1110-1-8, Vol. 430 Nov 11

F-11


PLY (1)


EP 1110-1-8(Vol. 8)

11/30/2011

INDUSTRY CODE

APPENDIX F

(Life =SOFTRAC 5000 hrs )

TJHB2 18-650-8 6.50 8.00 TL $29x 4TJHB3 18-850-10 8.50 10.00 TL $145x 4AJHB1 25-850-14 8.50 14.00 TL $252x 6HF-1AJHB5 27-850-15 8.50 15.00 TL $256x 4HF-1AJHB4 25-1050-15 10.50 15.00 TL $269x 4HF-1AJHB6 27-1050-15 10.50 15.00 TL $319x 4HF-1AJHB7 29-1250-15 12.50 15.00 TL $347x 4HF-1AJHB10 31-1250-15 12.50 15.00 TL $384x 4HF-1AJHB11 33-1250-15 12.50 15.00 TL $449x 4HF-1AJHB8 31-1350-15 13.50 15.00 TL $422x 4HF-1AJHB9 31-1550-15 15.50 15.00 TL $488x 4HF-1

(Life =SUPER TERRA GRIP 5000 hrs )

AJHC3 29-1250-15 12.50 15.00 TL $355x 6HF-2AJHC6 31-1550-15 15.50 15.00 TL $624x 8HF-2AJHC7 38-2000-16.1 20.00 16.00 TL $1,279x 8HF-2

(Life =SURE GRIP LUG 5000 hrs )

AJHD9 27-850-15 8.50 15.00 TL $294x 6HF-2AJHD1 10-16.5 10.00 16.50 TL $316x 6AJHD10 27-1050-15 10.50 15.00 TL $281x 6HF-2AJHD4 12-165 12.00 16.50 TL $414x 10AJHD3 12-165 12.00 16.50 TL $380x 8AJHD5 14-175 14.00 17.50 TL $566x 10I-3AJHD6 15-19.5 15.00 19.50 TL $765x 12I-3AJHD7 15-195 15.00 19.50 TL $765x 12I-3

(Life =IT 323 5000 hrs )

AJHE1 10-165 10.00 16.50 TL $326x 8AJHE3 12-165 12.00 16.50 TL $422x 10AJHE4 31-1550-15 15.50 15.00 TL $1,093x 8

(Life =POWER RIB 5000 hrs )

TJHJ1 18-850-8 8.50 8.00 TL $118x 4TJHJ2 20-1000-10 10.00 10.00 TL $52x 4

(Life =RALLY 5000 hrs )

TJHK1 480-8 4.80 8.00 TL $57x 4


EP 1110-1-8, Vol. 430 Nov 11

F-12


PLY (1)


EP 1110-1-8(Vol. 8)11/30/2011

INDUSTRY CODE

APPENDIX F

TJHK2 18-950-8 9.50 8.00 TL $39x 4

(Life =TERRA RIB 5000 hrs )

AJHM2 25-750-15 7.50 15.00 TL $189x 6HF-1AJHM4 27-950-15 9.50 15.00 TL $288x 10HF-1AJHM6 31-1350-15 13.50 15.00 TL $575x 8HF-1

(Life =ATV 5000 hrs )

TJHN1 AT21-7-10 7.00 10.00 TL $128x X3TJHN3 AT23-8-11 8.00 11.00 TL $146x 6TJHN5 AT24-9-11 9.00 11.00 TL $193x 6

(Life =TRACKER ATT 5000 hrs )

TJHT1 AT24-8-11 8.00 11.00 TL $188x X2TJHT2 AT24-10-11 10.00 11.00 TL $180x X2

INDUSTRIAL, MINE SERVICE

(Life =HARD ROCK LUG MINE & INDUSTRIAL 5000 hrs )

TKJC1 10.00-20 10.00 20.00 TT $1,056x 18

(Life =XTRA TRACTION LUG 5000 hrs )

AKJD2 825-15 8.25 15.00 TT $783x 16AKJD3 36-11x15(10.00L15) 10.00 15.00 TT $964x 16AKJD7 24x12x12 12.00 12.00 TL $502x 24AKJD6 35-15x15(14.50L-15) 15.00 15.00 TL $1,356x 28

(Life =XTRA TRACTION GRIP 5000 hrs )

AKJE1 32x15-15 15.00 15.00 TL $1,245x 24

OFF-THE-ROAD, MED & HEAVY COMMERCIAL, RADIAL

(Life =G-2 GRADER SERVICE - RL2F, SG2B 3200 hrs )

AMLA1 14.00R24 14.00 24.00 TL $1,749x X1G2

(Life =E-2 HAULAGE SERVICE - RL2F/GP2B RL2+ 2800 hrs )

AMLB1 17.5R25 17.50 25.00 TL $1,420x X1E/L/G3AMLB8 1800R25 18.00 25.00 TL $4,892x X2L5AMLB2 20.5R25 20.50 25.00 TL $2,747x X1E/L/G3AMLB9 20.5R25 20.50 25.00 TL $2,747x X2E/L/G3AMLB5 20.5R25 20.50 25.00 TL $3,510x X2E/K 3T


EP 1110-1-8, Vol. 430 Nov 11

F-13


PLY (1)


EP 1110-1-8(Vol. 8)

11/30/2011

INDUSTRY CODE

APPENDIX F

AMLB15 21.00R35 21.00 35.00 TL $8,477x X2E4AMLB3 23.5R25 23.50 25.00 TL $2,819x X1E/L/G3AMLB10 23.5R25 23.50 25.00 TL $3,013x X2E/L/G3AMLB22 29.5R25 29.50 25.00 TL $7,378x X2E/L 3AMLB21 295R29 29.50 29.00 TL $8,094x X2E/L/G 3+TAMLB17 3725R35 37.25 35.00 TL $12,624x X2E3AMLB23 40.5/75R39 40.50 39.00 TL $14,881x X2E3+

(Life =E-3 HAULAGE SERVICE - ROCK DESIGN RL3, RL3J, R 2800 hrs )

AMLC3 1800R33 18.00 33.00 TL $6,229x X3E3+AMLC5 24.00R35 24.00 35.00 TL $8,628x X2E3+AMLC6 29.5R29 29.50 29.00 TL $8,004x X2E3AMLC7 3725R35 37.25 35.00 TL $12,624x X2E3AMLC8 37.25R35 37.35 35.00 TL $12,624x X2E3AMLC9 37.5R39 37.50 39.00 TL $13,914x X2E3

(Life =E-4 RL4J/RL4 & RL4H/RL4 E4 5000 hrs )

AMLD1 12.00R24 12.00 24.00 TT $1,974x X3E4AMLD2 14.00R24 14.00 24.00 TL $2,679x X3E4AMLD3 14.00R25 14.00 25.00 TL $2,679x X3E4AMLD4 1800R25 18.00 25.00 TL $4,013x X2E4AMLD5 18.00R33 18.00 33.00 TL $5,641x X2E4AMLD14 21.00R35 21.00 35.00 TL $162x X2E4AMLD15 24.00R35 24.00 25.00 TL $9,809x X2E4AMLD7 27.00R49 27.00 49.00 TL $15,737x X2E4AMLD8 30.00R51 30.00 51.00 TL $17,427x X2E4AMLD9 33.00R51 33.00 51.00 TL $21,521x X2E4AMLD10 36.00R51 36.00 51.00 TL $24,649x X2E4AMLD11 37.00R57 37.00 57.00 TL $45,313x X2E4AMLD12 40.00R57 40.00 57.00 TL $45,900x X2E4

(Life =MOBILE CRANE 5000 hrs )

AMLF1 445/95R25 17.50 25.00 TL $2,769x UKE/L/G3AMLF3 525/80R25 (20.5R25) 20.60 25.00 TL $2,747x UKE/L/G3

(Life =L-5 DOZER & LOADER SERVICE RL5K 8000 hrs )

AMLG1 20.5R25 20.50 25.00 TL $4,050x X1L5AMLG2 23.5R25 23.50 25.00 TL $5,304x X2L5


EP 1110-1-8, Vol. 430 Nov 11

F-14


PLY (1)


EP 1110-1-8(Vol. 8)11/30/2011

INDUSTRY CODE

APPENDIX F

(Life =SPECIAL SERVICE - AT2A 5000 hrs )

AMLH1 14.00R20 14.00 20.00 TL $1,749x 18E/L/G 3AMLH3 16.00R20 16.00 20.00 TL $2,313x 22E/L/G 3AMLH4 16.00R21 16.00 21.00 TL $2,425x 22E/L/G 3AMLH6 1600R21 16.00 21.00 TL $2,425x X1E/L/G3AMLH2 17.5R25 17.50 25.00 TL $1,420x X1E/L/G3

OFF-THE-ROAD, MED & HEAVY COMMERCIAL, BIAS

(Life =INDUSTRIAL SURE GRIP MPT 5000 hrs )

ANMA1 10.5-20 10.50 20.00 TL $412x 10ANMA2 12.5-20 12.50 20.00 TL $526x 10

(Life =E-1 HRR 1A 2500 hrs )

ANMB1 1400-24 14.00 24.00 TT $1,928x 20E3ANMB2 1600-25 16.00 25.00 TL $2,684x 32E1

(Life =E-2 TRACTION EARTHMOVER SURE GRIP 2800 hrs )

ANMC3 18.00-25 18.00 25.00 TL $1,935x 16E7

(Life =E-3 ROCK SERVICE HARD ROCK LUG/HRL WC 2800 hrs )

ANME1 12.00-20 12.00 20.00 TT $1,084x 20E3ANME2 12.00-24 12.00 24.00 TT $1,205x 16E3ANME4 14.00-25 14.00 24.00 TL $1,996x 28E3ANME3 14.00-24 14.00 24.00 TT $1,812x 28E3ANME6 1600-25 16.00 25.00 TL $3,178x 28E3

(Life =E-3 ROCK SERVICE SUPER HARD ROCK LUG 2800 hrs )

ANMF1 26.5-25 26.50 25.00 TL $5,706x 24L5ANMF4 29.5-25 29.50 25.00 TL $7,887x 28L5ANMF5 29.5-29 29.50 29.00 TL $6,873x 28L4ANMF6 29.5-29 29.50 29.00 TL $6,451x 34E3

(Life =E-3 ROCK SERVICE SHRL8 2800 hrs )

ANMG4 29.5-35 29.50 35.00 TL $6,785x 34E3ANMG1 33.25-29 33.25 29.00 TL $7,083x 26E3TNMG6 33.25-35 33.25 35.00 TL $11,720x 38E3ANMG7 37.25-35 37.25 35.00 TL $8,954x 36E3ANMG9 375-39 37.50 39.00 TL $14,232x 52E3


EP 1110-1-8, Vol. 430 Nov 11

F-15


PLY (1)


EP 1110-1-8(Vol. 8)

11/30/2011

INDUSTRY CODE

APPENDIX F

(Life =E-3 ROCK SERVICE ELV3A, ELV4B, ELV4/5A 2800 hrs )

ANMH9 1800-25 18.00 25.00 TL $3,707x 40IND 3ANMH4 18.00-25 18.00 25.00 TL $5,152x 40IND 5S

(Life =E-3 ROCK SERVICE HRL 3F 2800 hrs )

ANMJ5 37.25-35 37.25 35.00 TL $12,411x 36E3ANMJ6 3725-35 37.25 35.00 TL $12,411x 36E3ANMJ2 3725-35 37.25 35.00 TL $12,411x 36E3

(Life =E-3 ROCK SERVICE WRL 3A 2800 hrs )

ANML1 14.00-20 14.00 20.00 TT $1,597x 24E3ANML2 14.00-24 14.00 24.00 TT $1,692x 24E3

(Life =E-4 ROCK SERVICE HRL 4B 5000 hrs )

ANMN1 16.00-25 16.00 25.00 TL $3,643x 28E4ANMN3 18.00-33 18.00 33.00 TL $4,942x 32E4ANMN4 21.00-35 21.00 35.00 TL $7,502x 36E4ANMN5 24.00-35 24.00 35.00 TL $10,157x 42E4ANMN9 36.00-51 36.00 51.00 TL $31,489x 58E4

(Life =E-7 FLOTATION TYPE SAND RIB SRB 7A 3000 hrs )

TNMQ1 14.00-20 14.00 20.00 TL $1,291x 10E7TNMQ2 16.00-24 16.00 24.00 TL $2,542x 12E7TNMQ3 18.00-25 18.00 25.00 TL $3,299x 16E7

(Life =E-7 FLOTATION TYPE PAVER TIRE 3000 hrs )

ANMR1 1600-24 16.00 24.00 TL $1,400x 12E7

(Life =G-2 SGG2A 3200 hrs )

ANMT1 13.00-24 13.00 24.00 TL $386x 10G2ANMT10 13.00-24 13.00 24.00 TL $386x 12G2ANMT8 16.00-24 16.00 24.00 TL $1,679x 12G2ANMT6 1600-24 16.00 24.00 TL $1,679x 16G2

(Life =G-2 SGLDL 2A L2 3200 hrs )

ANMV3 17.5-25 17.50 25.00 TL $849x 12L2/G2ANMV2 17.5-25 17.50 25.00 TL $849x 12L2/G2ANMV4 17.5-25 17.50 25.00 TL $1,024x 16L2/G2ANMV5 17.5-25 17.50 25.00 TL $1,156x 20L2/G2


EP 1110-1-8, Vol. 430 Nov 11

F-16


PLY (1)


EP 1110-1-8(Vol. 8)11/30/2011

INDUSTRY CODE

APPENDIX F

(Life =G-2 SGLEL 2A ES/L2/G2 3200 hrs )

ANMW1 20.5-25 20.50 25.00 TL $2,684x 12E/L/G2ANMW2 20.5-25 20.50 25.00 TL $1,221x 16E/L/G2ANMW4 23.5-25 23.50 25.00 TL $1,755x 12E/L/G2ANMW5 23.5-25 23.50 25.00 TL $1,999x 16E/L/G2

(Life =G-3 RKG 3A 3200 hrs )

TNMX1 14.00-24 14.00 24.00 TL $1,001x 14G2

(Life =L-2 DOZER/LOADER SERVICE TRACTION SG LUG DL 3200 hrs )

ANNA2 26.5-25 26.50 25.00 TL $3,655x 20L3

(Life =L-3 DOZER/LOADER SERVICE ROCK SERVICE E3/L3 3200 hrs )

ANNB1 205-25 20.50 25.00 TL $2,933x 20E/G/L3ANNB2 235-25 23.50 25.00 TL $3,508x 16E/G/L3ANNB5 23.5-25 23.50 25.00 TL $3,508x 16E/L 3ANNB6 23.5-25 23.50 25.00 TL $3,694x 20E/L 3

(Life =L-3 DOZER/LOADER SERVICE ROCK SHRL DL 3200 hrs )

ANNC1 26.5-25 26.50 25.00 TL $3,655x 20L3ANNC3 29.5-25 29.50 25.00 TL $6,873x 28L4

(Life =L-3 DOZER/LOADER SERVICE ROCK HRL DL 3A & 3F 3200 hrs )

ANND4 17.5-25 17.50 25.00 TL $1,208x 20L/G3ANND2 265-25 26.50 25.00 TL $5,495x 20L/G3

(Life =L-4 DOZER/LOADER SERVICE ROCK DEEP TREAD S 5000 hrs )

ANNE2 26.5-25 26.50 25.00 TL $3,655x 20L3ANNE4 29.5-25 29.50 25.00 TL $6,873x 28L4ANNE5 29.5-29 29.50 29.00 TL $6,451x 34E3

(Life =L-4 DOZER/LOADER SERVICE ROCK DEEP TREAD N 5000 hrs )

TNNG1 35/65-33 35.00 33.00 TL $16,115x 42L5

(Life =L-5 DOZER/LOADER SERVICE ROCK SUPER XTRA T 8000 hrs )

ANNL2 35/65-33 35.00 33.00 TL $11,977x 30L5ANNL4 41.25/70-39 41.25 39.00 TL $14,882x 42L5ANNL7 45/65-45 45.00 45.00 TL $27,397x 58L5


EP 1110-1-8, Vol. 430 Nov 11

F-17


PLY (1)


EP 1110-1-8(Vol. 8)

11/30/2011

INDUSTRY CODE

APPENDIX F

(Life =L-5 DOZER/LOADER SERVICE SMOOTH SMO SL5B 8000 hrs )

ANNN3 18.00-25 18.00 25.00 TL $3,707x 40IND3

(Life =L-5 DOZER/LOADER SERVICE SMOOTH SUPER XTRA 8000 hrs )

ANNO1 295-25 29.50 25.00 TL $8,590x 28L5SANNO4 29.5-25 29.50 25.00 TL $8,590x 28L5SANNO3 295-25 29.50 25.00 TL $8,590x 28L5S

(Life =L-5 DOZER/LOADER SERVICE SMOOTH NSM DL5B 8000 hrs )

ANNP1 35/65-33 35.00 33.00 TL $10,956x 24L5

INDUSTRIAL, SOLID

(Life =SOLID, HIGH PERFORMANCE, OIL RESISTANT/STATI 5000 hrs )

IPPO5 10x3x6-1/4 Grip 3.00 10.00 NO $345xIPPO4 10x3-1/2x6 3.50 10.00 NO $373xIPPO18 12x3-1/2x8 3.50 12.00 NO $381xIPPO23 13x3-1/2x8 3.50 13.00 NO $433xIPPO32 15x3-1/2x11-1/4 3.50 15.00 NO $409xIPPO1 81/2-4-4 4.00 8.50 NO $472xIPPO10 10x4x6-1/2 4.00 10.00 NO $326xIPPO6 10x4x6-1/4 4.00 10.00 NO $381xIPPO19 12x4x8 4.00 12.00 NO $417xIPPO47 16-1/4x4x11-1/4 Lug 4.00 16.25 NO $515xIPPO30 14x4-1/2x8 4.50 14.00 NO $566xIPPO40 16x4-1/2x10-1/2 Lug 4.50 16.00 NO $615xIPPO2 9-5-5 Grip 5.00 9.00 NO $353xIPPO12 10x5x6-1/2 5.00 10.00 NO $339xIPPO7 10x5x6-1/4 5.00 10.00 NO $380xIPPO13 10-1/2x5x5 5.00 10.50 NO $554xIPPO31 14x5x10 5.00 14.00 NO $519xIPPO33 15x5x11-1/4 5.00 15.00 NO $500xIPPO38 15-1/2x5x10 5.00 15.50 NO $582xIPPO41 16x5x10-1/2 5.00 16.00 NO $642xIPPO48 16-1/4x5x11-1/4 5.00 16.25 NO $555xIPPO53 17x5x12-1/8 5.00 17.00 NO $633xIPPO63 18x5x14 5.00 18.00 NO $565xIPPO58 18x5x12-1/8 5.00 18.00 NO $672x


EP 1110-1-8, Vol. 430 Nov 11

F-18


PLY (1)


EP 1110-1-8(Vol. 8)11/30/2011

INDUSTRY CODE

APPENDIX F

IPPO68 20x5x16 5.00 20.00 NO $752xIPPO73 21x5x15 5.00 21.00 NO $782xIPPO79 22x5x16 5.00 22.00 NO $835xIPPO8 10x6x6-1/4 6.00 10.00 NO $459xIPPO14 10-1/2x6x5 6.00 10.50 NO $576xIPPO34 15x6x11-1/4 6.00 15.00 NO $531xIPPO42 16x6x10-1/2 6.00 16.00 NO $721xIPPO49 16-1/4x6x11-1/4 6.00 16.25 NO $655xIPPO59 18x6x12-1/8 6.00 18.00 NO $756xIPPO69 20x6x16 6.00 20.00 NO $800xIPPO74 21x6x15 6.00 21.00 NO $978xIPPO80 22x6x16 6.00 22.00 NO $987xIPPO22 12-6-1/2x8 6.50 12.00 NO $577xIPPO9 10x7x6-1/4 7.00 10.00 NO $534xIPPO35 15x7x11-1/4 7.00 15.00 NO $662xIPPO43 16x7x10-1/2 7.00 16.00 NO $826xIPPO50 16-1/4x7x11-1/4 7.00 16.25 NO $815xIPPO60 18x7x12-1/8 7.00 18.00 NO $788xIPPO70 20x7x16 7.00 20.00 NO $760xIPPO75 21x7x15 7.00 21.00 NO $1,004xIPPO81 22x7x16 7.00 22.00 NO $1,184xIPPO94 26x7x20 7.00 26.00 NO $1,481xIPPO36 15x8x11-1/4 8.00 15.00 NO $792xIPPO61 18x8x12-1/8 8.00 18.00 NO $925xIPPO66 18x8x14 8.00 18.00 NO $964xIPPO71 20x8x16 8.00 20.00 NO $1,034xIPPO76 21x8x15 8.00 21.00 NO $1,224xIPPO82 22x8x16 8.00 22.00 NO $1,278xIPPO37 15x9x11-1/4 9.00 15.00 NO $1,053xIPPO67 18x9x14 9.00 18.00 NO $964xIPPO62 18x9x12-1/8 9.00 18.00 NO $1,095xIPPO72 20x9x16 9.00 20.00 NO $1,403xIPPO77 21x9x15 9.00 21.00 NO $1,464xIPPO116 22x9x16 9.00 22.00 NO $1,452xIPPO83 22x9x16 9.00 22.00 NO $1,452xIPPO92 22x10x17-3/4 10.00 22.00 NO $1,756xIPPO84 22x10x16 10.00 22.00 NO $1,964x


EP 1110-1-8, Vol. 430 Nov 11

F-19


PLY (1)


EP 1110-1-8(Vol. 8)

11/30/2011

INDUSTRY CODE

APPENDIX F

IPPO95 28x10x22 10.00 28.00 NO $2,359xIPPO99 36-10-30 10.00 36.00 NO $843xIPPO78 21x12x15 12.00 21.00 NO $2,352xIPPO86 22x12x16 12.00 22.00 NO $2,070xIPPO96 28x12x22 12.00 28.00 NO $3,068xIPPO87 22x14x16 14.00 22.00 NO $2,306xIPPO93 22x14x17-3/4 14.00 22.00 NO $2,666xIPPO88 22x16x16 16.00 22.00 NO $2,542xIPPO98 28x16x22 16.00 28.00 NO $4,368x

CONVEYOR/LOADER BELTING

(Life =CONVEYOR BELTING (GOODYEAR EP) 5000 hrs )

AZZA1 Conveyor Belting 24.00 50.00 NO $756x 2AZZA2 Conveyor Belting 24.00 60.00 NO $906x 2AZZA3 Conveyor Belting 24.00 70.00 NO $1,058x 2AZZA4 Conveyor Belting 24.00 80.00 NO $1,209x 2AZZA5 Conveyor Belting 24.00 90.00 NO $1,361x 2AZZA6 Conveyor Belting 24.00 100.00 NO $1,511x 2AZZA7 Conveyor Belting 24.00 110.00 NO $1,662x 2AZZA8 Conveyor Belting 24.00 120.00 NO $1,814x 2AZZA9 Conveyor Belting 24.00 130.00 NO $1,964x 2AZZA10 Conveyor Belting 24.00 140.00 NO $2,116x 2AZZA11 Conveyor Belting 24.00 150.00 NO $2,267x 2AZZA12 Conveyor Belting 30.00 50.00 NO $945x 2AZZA13 Conveyor Belting 30.00 60.00 NO $1,133x 2AZZA14 Conveyor Belting 30.00 70.00 NO $1,322x 2AZZA15 Conveyor Belting 30.00 80.00 NO $1,511x 2AZZA16 Conveyor Belting 30.00 90.00 NO $1,700x 2AZZA17 Conveyor Belting 30.00 100.00 NO $1,889x 2AZZA18 Conveyor Belting 30.00 110.00 NO $2,078x 2AZZA19 Conveyor Belting 30.00 120.00 NO $2,267x 2AZZA20 Conveyor Belting 30.00 130.00 NO $2,456x 2AZZA21 Conveyor Belting 30.00 140.00 NO $2,645x 2AZZA22 Conveyor Belting 30.00 150.00 NO $2,834x 2AZZA23 Conveyor Belting 36.00 50.00 NO $1,133x 2AZZA24 Conveyor Belting 36.00 60.00 NO $1,361x 2AZZA25 Conveyor Belting 36.00 70.00 NO $1,587x 2


EP 1110-1-8, Vol. 430 Nov 11

F-20


PLY (1)


EP 1110-1-8(Vol. 8)11/30/2011

INDUSTRY CODE

APPENDIX F

AZZA26 Conveyor Belting 36.00 80.00 NO $1,814x 2AZZA27 Conveyor Belting 36.00 90.00 NO $2,040x 2AZZA28 Conveyor Belting 36.00 100.00 NO $2,267x 2AZZA29 Conveyor Belting 36.00 110.00 NO $2,494x 2AZZA30 Conveyor Belting 36.00 120.00 NO $2,720x 2AZZA31 Conveyor Belting 36.00 130.00 NO $2,947x 2AZZA32 Conveyor Belting 36.00 140.00 NO $3,173x 2AZZA33 Conveyor Belting 36.00 150.00 NO $3,400x 2AZZA34 Conveyor Belting 42.00 50.00 NO $1,322x 2AZZA35 Conveyor Belting 42.00 60.00 NO $1,587x 2AZZA36 Conveyor Belting 42.00 70.00 NO $1,851x 2AZZA37 Conveyor Belting 42.00 80.00 NO $2,116x 2AZZA38 Conveyor Belting 42.00 90.00 NO $2,381x 2AZZA39 Conveyor Belting 42.00 100.00 NO $2,645x 2AZZA40 Conveyor Belting 42.00 110.00 NO $2,909x 2AZZA41 Conveyor Belting 42.00 120.00 NO $3,173x 2AZZA42 Conveyor Belting 42.00 130.00 NO $3,439x 2AZZA43 Conveyor Belting 42.00 140.00 NO $3,703x 2AZZA44 Conveyor Belting 42.00 150.00 NO $3,967x 2AZZA45 Conveyor Belting 48.00 50.00 NO $1,808x 3AZZA46 Conveyor Belting 48.00 60.00 NO $2,169x 3AZZA47 Conveyor Belting 48.00 70.00 NO $2,531x 3AZZA48 Conveyor Belting 48.00 80.00 NO $2,892x 3AZZA49 Conveyor Belting 48.00 90.00 NO $3,254x 3AZZA50 Conveyor Belting 48.00 100.00 NO $3,615x 3AZZA51 Conveyor Belting 48.00 110.00 NO $3,977x 3AZZA52 Conveyor Belting 48.00 120.00 NO $4,339x 3AZZA53 Conveyor Belting 48.00 130.00 NO $4,699x 3AZZA54 Conveyor Belting 48.00 140.00 NO $5,061x 3AZZA55 Conveyor Belting 48.00 150.00 NO $5,423x 3AZZA56 Conveyor Belting 60.00 50.00 NO $3,494x 4AZZA57 Conveyor Belting 60.00 60.00 NO $4,192x 4AZZA58 Conveyor Belting 60.00 70.00 NO $4,892x 4AZZA59 Conveyor Belting 60.00 80.00 NO $5,591x 4AZZA60 Conveyor Belting 60.00 90.00 NO $6,291x 4AZZA61 Conveyor Belting 60.00 100.00 NO $6,989x 4AZZA62 Conveyor Belting 60.00 110.00 NO $7,687x 4


EP 1110-1-8, Vol. 430 Nov 11

F-21


PLY (1)


EP 1110-1-8(Vol. 8)

11/30/2011

INDUSTRY CODE

APPENDIX F

AZZA63 Conveyor Belting 60.00 120.00 NO $8,386x 4AZZA64 Conveyor Belting 60.00 130.00 NO $9,084x 4AZZA65 Conveyor Belting 60.00 140.00 NO $9,784x 4AZZA66 Conveyor Belting 60.00 150.00 NO $10,483x 4


EP 1110-1-8, Vol. 430 Nov 11

F-22

APPENDIX G TIRE LIFE AND TIRE WEAR FACTORS

EP 1110-1-8, Vol. 430 Nov 11

G-1

APPENDIX G

Tire Life and Tire Wear Factors

SECTION I. TIRE WEAR FACTORS The tire wear factors used in this pamphlet are listed in appendix D. The “useful life” of a new tire is the product of Condition Factors (CF) from I through V, the Wheel Position Factor (WPF), the Grade Factor (GF) (for Drive Tires only) and the Miscellaneous Condition (MC). These factors provide a percentage reduction to the maximum tire life. See chapter 2 for tire cost methodology. Condition Factors, Wheel Position Factors, Grade Factor, and Miscellaneous Condition are derived from the Caterpillar Performance Handbook. The factors shown below are examples specifically for a rear dump wagon.

Condition Factors (CF): Average Severe I. Maintenance 0.981 0.763 II. Speed 0.872 0.763 III. Curves 0.981 0.872 IV. Surface Condition 0.981 0.763 V. Loads 1.090 0.709 CF Product of the factors 0.897 0.275 (I x II x III x IV x V)

VI. Wheel Position Factors (WPF): WPF-FT Front Tire (FT) 0.981 0.981 WPF-DTR Drive Tire (DT) - Rear Dump 0.818 0.709 WPF-TT Trailing Tire (TT) 1.090 1.090 VII. Grade Factor (GF) (Drive Tires Only) 0.981 0.763 VIII. Miscellaneous Condition (MC) 1.090 0.981

EP 1110-1-8, Vol. 430 Nov 11

G-2

APPENDIX G

TIRE LIFE AND TIRE WEAR FACTORS (Continued)

SECTION I. TIRE WEAR FACTORS (Continued)

Example: Final Tire Wear Factors for Wagon, Rear Dump (See Appendix D, Category W15)

Average Severe Front Tire - Average = (CF = 0.897)(WPF-FT = 0.981)(MC = 1.090) 0.96 Front Tire - Severe = (CF = 0.275)(WPF-FT = 0.981)(MC = 0.927) 0.60 Drive Tire - Average = (CF = 0.897)(WPF-DTR = 0.763)(GF = 0.981)(MC = 1.090) 0.78 Drive Tire - Severe = (CF = 0.275)(WPF-DTR = 0.732)(GF = 0.763)(MC = 0.927) 0.15 Trailing Tire - Average = (CF = 0.897)(WPF-TT = 1.090)(MC = 1.090) 1.07 Trailing Tire - Severe = (CF = 0.275)(WPF-TT = 1.090)(MC = 0.927) 0.29 SECTION II. MAXIMUM TIRE LIFE Maximum tire life is used in the formula to determine tire wear cost and is located in Appendix F by type of tire.

EP 1110-1-8, Vol. 430 Nov 11

G-3


EP 1110-1-8, Vol. 430 Nov 11

G-4

APPENDIX H MANUFACTURER LIST

EP 1110-1-8, Vol. 430 Nov 11

H-1

APPENDIX HMANUFACTURER LIST

EP 1110-1-8(Vol. 1)

11/30/2011

CODE MANUFACTURER

A1 ALLIED-GATOR, INC.-

A2 ASV INC.-

A3 AMERICAN PILEDRIVING EQUIPMENT, INC.-

A4 ATLAS COPCO WAGNER INC.-

AA AMERICAN AUGERS, INC.-

AB ALLMAND BROTHERS INC.-

AC ACE ENTERPRISES-

AD ACKER DRILL COMPANY INC.-

AE AEROIL PRODUCTS COMPANY, INC.-

AF AIRPLACO EQUIPMENT CO., INC.-

AG ARROW-MASTER, INC.-

AH AUTO CRANE CO.-

AI AMIDA INDUSTRIES, INC.-

AJ ALLEN ENGINEERING CORP.-

AK TYLER EQUIPMENT CO.-

AL ALLENTOWN EQUIPMENT-

AM AMERICAN CRANE CORPORATION (TEREX)-

AN ATLANTIC-

AO ALKOTA CLEANING SYSTEMS, INC.-

AP PECCO AND WOLFF TOWER CRANES (MORROW)-

AQ AQUATICS UNLIMITED-

AR AMERICAN ROAD MACHINERY, INC.-

AS ATLAS COPCO CONSTRUCTION TOOLS INC.-

AT ANDERSON MAVOR INC.-

AU ALLIED CONSTRUCTION PRODUCTS-

AV ALIVA LTD.-

AW AIRMAN (HOKUETSU INDUSTRIES CO. LTD.)-

AX AMERICAN COMPACTION EQUIPMENT, INC.-

H-1

EP 1110-1-8, Vol. 430 Nov 11

H-2


EP 1110-1-8(Vol. 1)11/30/2011

CODE MANUFACTURER

AY KOMLINE-SANDERSON ENGINEERING CO.-

AZ ALLIS-CHALMERS CORP.-

BA BADGER EQUIPMENT CO.-

BB BASCO-

BC NORTH STAR ENGINEERED PRODUCTS, INC.-

BD BRODERSON MANUFACTURING CORPORATION-

BE INGERSOLL RAND MATERIAL HANDLING-

BF BENFORD-

BG BARBER-GREENE COMPANY-

BI BOR-IT MANUFACTURING COMPANY INC.-

BJ BURKEEN MANUFACTURING CO.-

BK BLAW KNOX CONSTRUCTION EQUIPMENT CORP.-

BL US FILTER/BLASTRAC-

BM BROCE MANUFACTURING COMPANY-

BN BANDIT INDUSTRIES, INC.-

BO COMPACTION AMERICA (BOMAG)-

BQ BELL EQUIPMENT NORTH AMERICA INC .-

BR BROOKVILLE MINING EQUIPMENT CORP.-

BS BALDERSON, INC.-

BT BREAKER TECHNOLOGY INC.-

BU BUSH HOG-

BW BOWIE INDUSTRIES, INC.-

BX BIL-JAX, INC.-

C1 COYOTE LOADER SALES, INC.-

C2 CARELIFT EQUIPMENT-

C3 TIME CONDOR CORPORATION-

C4 CATERPILLAR LIFT TRUCKS,-

C5 Construction Equipment Company-

H-2

EP 1110-1-8, Vol. 430 Nov 11

H-3


EP 1110-1-8(Vol. 1)

11/30/2011

CODE MANUFACTURER

CA CATERPILLAR INC. ( MACHINE DIVISION)-

CB CONSOLIDATED BALING MACHINE COMPANY, INC-

CC CEMEN TECH-

CD CDS GROUP-

CE ATHEY PRODUCTS CORPORATION-

CF CGR COMPACTING-

CG CHEMGROUT, INC.-

CH CHAMPION ROAD MACHINERY-PRO PAV (WIRTGEN-

CI CHIPMORE MANUFACTURING CO., INC.-

CJ COLD JET-

CK CHICAGO PNEUMATIC TOOL CO.-

CL CON-E-CO-

CM CLEMCO INDUSTRIES CORPORATION-

CN CEMEN TECH, INC.-

CO WASTE CONTROL SYSTEMS, INC.-

CP CRISAFULLI PUMP-

CQ CUSHION CUT, INC. (HUSQVARNA)-

CR CAMLEVER-

CS CASE CORPORATION-

CT CLEVELAND TRENCHER-

CU WASTEQUIP CUSCO INDUSTRIES-

CV CONMACO, INC.-

CW TEREX - CMI (TEREX ROADBUILDING)-

CX CMC (CONSTRUCTION MACHINERY COMPANY)-

CY CENTRIC-

CZ CLYDE IRON WORKS-

DA ELCO INTERNATIONAL INC.-

DD DELTA DREDGE & PUMP CORP.-

H-3

EP 1110-1-8, Vol. 430 Nov 11

H-4


EP 1110-1-8(Vol. 1)11/30/2011

CODE MANUFACTURER

DE DEMOLITION TECHNOLOGIES-

DF DURA FLOAT-

DG DAINONG HEAVY INDUSTRIES, INC.-

DH DAEWOO HEAVY INDUSTRIES LTD.-

DI DICKSON INDUSTRIES INC.-

DJ CATERPILLAR/DJB-

DL PILECO, INC.-

DN Dynatech-

DO DOSCO CORPORATION-

DR DRESSER MINING EQUIPMENT-

DS DREDGING SUPPLY COMPANY (DSC)-

DT DRILTECH, INC. (SANDVIK)-

DW DITCH WITCH(The Charles Machine Works)I-

DY DYNAPAC DIVISION - SVEDALA INDUSTRIES-

EA EAGER BEAVER-

EC ELGIN SWEEPER COMPANY-

ED EQUIPMENT DEVELOPMENT CO., INC. (EDCO)-

EI EIMCO JARVIS CLARK-

EJ CEDARAPIDS INC., A TEREX COMPANY-

EL ELLICOTT MACHINE CORPORATION-

EM EXCEL MACHINERY LTD.-

EP ENVIRO-PAK-

ES ESCO CORPORATION-

ET E. D. ETNYRE & CO.-

EU EUCLID INDUSTRIES, INC.-

EX EXCEL INDUSTRIES, INC.-

EZ E-Z DRILL, INC.-

FC FERMEC NORTH AMERICA LTD., A TEREX CO.-

H-4

EP 1110-1-8, Vol. 430 Nov 11

H-5


EP 1110-1-8(Vol. 1)

11/30/2011

CODE MANUFACTURER

FE FELKER (TARGET)-

FG FINN CORPORATION-

FH FRUEHAUF TRAILER CORPORATION-

FI FIATALLIS-

FK FRANKLIN TREEFARMER-

FL FLETCHER MINING EQUIPMENT-

FN NEW HOLLAND NORTH AMERICA, INC.-

FO FORD MOTOR COMPANY-

FR FERGUSON MANUFACTURING & EQUIPMENT-

FS FIVE STAR MANUFACTURING CO/ELGIN SWEEPER-

FU FURUKAWA CO.,LTD.-

G1 GRACO, INC.-

GA GRADALL COMPANY-

GB GAR-BRO MANUFACTURING COMPANY-

GC GEHL COMPANY-

GD GARDNER-DENVER INDUSTRIAL MACHINES-

GE GENSCO AMERICA CO. LTD.-

GF GRIFFIN DEWATERING CORP.-

GH GEITH INC.-

GI GALION DIVISION-

GJ GENIE INDUSTRIES-

GL GARLOCK EQUIPMENT CO.-

GM GMC AND CHEVROLET-

GN GALION DUMP BODIES, INC.-

GO GOMACO CORPORATION-

GR GORMAN-RUPP COMPANY-

GT GILCREST EQUIPMENT COMPANY-

GV GROVE CRANES (MANITOWOC)-

H-5

EP 1110-1-8, Vol. 430 Nov 11

H-6


EP 1110-1-8(Vol. 1)11/30/2011

CODE MANUFACTURER

GW GROVE MANLIFT (JLG)-

HA HAZCO SERVICES, INC.-

HB HAWCO MANUFACTURING COMPANY, LLC-

HC HAMM COMPACTORS, INC.-

HD HYDRAULIC POWER SYSTEMS, INC.-

HE HENDRIX MANUFACTURING COMPANY, INC.-

HF HYDRA-MAC INTERNATIONAL, INC.-

HH ESG MANUFACTURING H&H PUMP & DREDGE-

HI HITACHI CONSTRUCTION MACHINERY-

HM H&M VIBRO, INC.-

HN HINO DIESEL TRUCKS (U.S.A.) INC.-

HO RIVERSIDE PUMP MANUFACTURING-

HP COMPACTION AMERICA-

HQ HYPAC COMPACTION EQUIPMENT-

HR HYDROCAL INC.-

HU HYUNDAI CONSTRUCTION EQUIPMENT-

HV HUSQVARNA FOREST & GARDEN CO.-

HW HEWITT-ROBINS-

HY HYSTER CO.-

HZ HOFFCO-COMET-

IA INGERSOLL RAND ROTARY-REC COMPRESSOR DIV-

IB INGERSOLL RAND ROTARY DRILL DIV-

IC INTERNATIONAL CONSTRUCTION EQUIPMENT,INC-

ID KOMATSU DRESSER-

IE IDEAL MANUFACTURING, INC.-

IF INGERSOLL RAND PORTABLE COMPRESSOR DIV-

IG INGRAM COMPACTING, LLC-

IH NAVISTAR INTERNATIONAL TRANSPORTATION-

H-6

EP 1110-1-8, Vol. 430 Nov 11

H-7


EP 1110-1-8(Vol. 1)

11/30/2011

CODE MANUFACTURER

IM INNOVATIVE MATERIAL SYSTEMS, INC. (IMS)-

IN INGERSOLL RAND CO.-

IP INGERSOLL RAND ROAD MACHINERY DIV-

IR INGERSOLL RAND ROCK DRILL DIV-

IS INSLEY DIVISION-

IT NAVISTAR INTERNATIONAL CORPORATION-

JC JCB INC.-

JD DEERE & COMPANY-

JE JCL EQUIPMENT CO.-

JL JLG INDUSTRIES, INC.-

JM JEFFREY MINING MACHINERY DIVISION-

JO C. S. JOHNSON COMPANY-

JR JRB COMPANY INC.-

JS JOHNSTON SWEEPER COMPANY-

JU ATI-Bell-

KA KAWASAKI LOADERS, INC.-

KB KOLBERG - PIONEER, INC-

KC KOBELCO AMERICA INC.-

KD K-D MANITOU, INC.-

KE KENWORTH TRUCK COMPANY-

KF KNAPHEIDE MANUFACTURING CO.-

KH KOHLER COMPANY-

KI KLEIN PRODUCTS, INC.-

KK KEENE ENGINEERING INC.-

KL KOLMAN / ATHEY DIV.-

KM Komatsu America International Company-

KN KENT DEMOLITION TOOLS-

KO KOEHRING CRANES, INC.-

H-7

EP 1110-1-8, Vol. 430 Nov 11

H-8


EP 1110-1-8(Vol. 1)11/30/2011

CODE MANUFACTURER

KP KOCH-WATER-

KR KORI CORPORATION-

KU KUBOTA TRACTOR CORPORATION-

KW KERSHAW MFG., CO.-

KZ KEIZER TECHNOLOGIES AMERICAS, INC-

LA LAYTON MANUFACTURING COMPANY-

LB LINK-BELT CONSTRUCTION EQUIPMENT CO.-

LC LINCOLN ELECTRIC COMPANY-

LD LEE-BOY-

LE LELY PACIFIC, INC.-

LF LOFTNESS / US ATTACHMENTS-

LG LITTLE GIANT CRANE & SHOVEL INC.-

LH MORROW EQUIPMENT COMPANY, LLC-

LI LINK-BELT CONSTRUCTION EQUIPMENT COMPANY-

LK LIFTKING INDUSTRIES, INC.-

LL OMNIQUIP, LULL-

LN LONDON MACHINERY INC.-

LO LORAIN CRANES DIVISION-

LS LAKE SHORE MINING EQUIPMENT INC.-

LU LABOUNTY MANUFACTURING,-

LY BOART LONGYEAR COMPANY-

LZ LIEBHERR CONSTRUCTION EQUIPMENT CO.-

M1 MANITEX - MANITOWOC BOOM TRUCKS GROUP-

M2 MAULDIN - CALDER BROTHERS CORP.-

M3 MAYCO PUMP - MULTIQUIP INC.-

M4 MITCHELL INDUSTRIAL TIRE COMPANY (MITCO)-

MA MANITOWOC ENGINEERING CO.-

MB M-B COMPANIES, INC.-

H-8

EP 1110-1-8, Vol. 430 Nov 11

H-9


EP 1110-1-8(Vol. 1)

11/30/2011

CODE MANUFACTURER

MC VME NORTH AMERICA-

MD MDI/YUTANI-

ME MELROE COMPANY/BOBCAT-

MF MF INDUSTRIAL-

MG McMASTER-CARR-

MH MITSUBISHI FUSO TRUCK OF AMERICA-

MI MITSUBISHI CONSTRUCTION EQUIP.-

MJ MILLER SPREADER CO.-

MK MKT MANUFACTURING, INC.-

ML ITT MARLOW PUMPS-

MM MACO-MUEDON-

MN GRANUTE-SATURN SYSTEMS(MAC CORPORATION)-

MO MORGEN MANUFACTURING CO.-

MP MIDLAND MACHINERY CO-

MQ MORBARK, INC.-

MR FOREMOST MOBILE DRILLING COMPANY, INC.-

MS MUSTANG UNITS COMPANY-

MT MACK TRUCKS, INC.-

MU MULTIQUIP, INC.-

MV MAYVILLE ENGINEERING CO., INC.-

MW M-B-W, INC.-

MX MAXON INDUSTRIES-

MY MIDLAND MANUFACTURING INC.-

MZ MARINE INLAND FABRICATORS-

NA NAGANO - LELY CORP.-

NB NASCO EQUIPMENT CO. INC.-

NC NATIONAL CRANE CORPORATION-

NE NEAL MANUFACTURING COMPANY, INC-

H-9

EP 1110-1-8, Vol. 430 Nov 11

H-10


EP 1110-1-8(Vol. 1)11/30/2011

CODE MANUFACTURER

NI NIFTYLIFT INC. - USA-

NL NLB CORPORATION-

NO NORTHWEST ENGINEERING COMPANY-

NP NPK CONSTRUCTION EQUIPMENT-

OE OLIN ENGINEERING, INC.-

OK O & K ORENSTEIN & KOPPEL INC.-

OL OLYMPYK CHAIN SAWS-

ON ONAN CORPORATION-

PA PALFINGER INC.-

PB PETTIBONE MICHIGAN LLC-

PC GETMAN BROTHERS MFG. COMPANY-

PE PETERBILT MOTORS COMPANY-

PH P & H-

PI PIQUA ENGINEERING-

PL PRO-LINE / ANVIL ATTACHMENTS-

PN PEMBERTON, INC.-

PO PROGRESSIVE DEVELOPMENT INC.-

PP PACIFIC RUBBER-

PR USFILTER PERRIN PRODUCTS-

PS POWER CURBERS, INC.-

PT PATENT CONSTRUCTION SYSTEMS-

PU PUTZMEISTER INC.-

PW POWERSCREEN INTERNATIONAL DISTRIBUTN LTD-

RA METSO MINERALS-

RC JOHNSON-ROSS (TEREX ROADBUILDING)-

RD REEDRILL (TEREX)-

RE NORSTAR PRODUCTS INTERNATIONAL, INC.-

RI REYNOLDS INTERNATIONAL, L.P.-

H-10

EP 1110-1-8, Vol. 430 Nov 11

H-11


EP 1110-1-8(Vol. 1)

11/30/2011

CODE MANUFACTURER

RK RAPID MIX-

RM ROME PLOW CO.-

RN ALLIED SYSTEMS COMPANY (RANGER)-

RO ROBBINS COMPANY-

RQ REED MANUFACTURING-

RR RAMMER - GR COSTRUTTORI - SANDVIK-

RS ROSCO, A LeeBoy COMPANY-

RT ROADTEC ( ASTEC INDUSTRIES COMPANY)-

RX RAMMAX MACHINERY CO.-

S1 STANLEY HYDRAULIC TOOLS-

S2 SCHRAMM, INC-

S3 CHAMPION ROAD MACHINERY - SUPERPAC CO.-

S4 SUPERIOR INDUSTRIES, AN ASTEC COMPANY-

S5 SOMAT WASTE REDUCTION TECHNOLOGY-

S6 SUPERIOR TIRE & RUBBER CORP.-

SA SAUERMAN (NATIONAL OILWELL VARCO)-

SB SCAT TRAK - OMNIQUIP - TEXTRON INC.-

SC SCHWING AMERICA INC.-

SD SIOUX STEAM CLEANER CORPORATION-

SE SEALMASTER, INC.-

SF SECO CORPORATION-

SG STONE CONSTRUCTION EQUIPMENT, INC.-

SH SHRED-TECH LIMITED-

SI SAKAI AMERICA, INC.-

SJ SKYJACK, INC.-

SK LTV ENERGY PRODUCTS (SKAGIT)-

SL SHUTTLELIFT, INC.-

SM SEAARK MARINE-

H-11

EP 1110-1-8, Vol. 430 Nov 11

H-12


EP 1110-1-8(Vol. 1)11/30/2011

CODE MANUFACTURER

SN STEPHENS MANUFACTURING CO., INC.-

SO SOUTHWEST CONSTRUCTION EQUIPMENT CO.-

SP SPRAGUE AND HENWOOD-

SQ SCHAEFF INC.-

SR SULLAIR CORPORATION-

SS SAMSUNG CONSTRUCTION EQUIPMENT AMERICA-

ST STOW MANUFACTURING, INC.-

SU SULLIVAN-PALATEK, INC.-

SV SOMERO ENTERPRISES, INC.-

SW SNORKEL-

SX SELLICK EQUIPMENT LIMITED-

SY SKY TRAK - OMNIQUIP - TEXTRON INC.-

SZ STRATO-LIFT INTERNATIONAL CORP.-

TA TAMPO MANUFACTURING CO., INC.-

TB TERRAMITE CONSTRUCTION EQUIPMENT-

TC TCM-

TD TADANO AMERICA CORPORATION-

TE TEREX CORPORATION-

TF THOMAS EQUIPMENT LTD.-

TG TIMBCO HYDRAULICS, INC.-

TH TEEMARK CORPORATION-

TI TIMBERJACK, A JOHN DEERE COMPANY-

TJ TRAMAC-

TK TAKEUCHI MFG. (U.S.), LTD-

TL BREAKER TECHNOLOGY, INC. (AN ASTEC CO.)-

TM TESMEC USA, INC.-

TO TORO-

TR TEREX MINING-

H-12

EP 1110-1-8, Vol. 430 Nov 11

H-13


EP 1110-1-8(Vol. 1)

11/30/2011

CODE MANUFACTURER

TS TELSMITH INC.-

TT TRAIL KING INDUSTRIES, INC.-

TU TITAN INTERNATIONAL, INC.-

TV TRAVERSE LIFT CO.-

UE UNDERGROUND EQUIPMENT & SUPPLY-

UL UNIVERSAL ENGINEERING - SVEDALA - METSO-

UN UNIT RIG-

UP UPRIGHT INC.-

VA VOEST-ALPINE-

VB VIBROMAX AMERICA INC.-

VE VERMEER MANUFACTURING CO.-

VI VINCE HAGAN COMPANY-

VO VOLVO CONSTRUCTION EQUIPMENT GROUP-

VP VOGELE AMERICA - PRO-PAV DIV.-

VS VALLEY SLURRY SEAL / MACROPAVER DIVISION-

VT VALMET - PARTEK FOREST LLC-

VU VULCAN FOUNDATION EQUIPMENT, INC-

WA HAULPAK DIVISION-

WB WEBER MASCHINENTECHNIK GMBH-

WC WACKER CORPORATION-

WD WALDON, INC.-

WE WEATHERFORD U.S. INC.-

WF WATSON INC.-

WG ATLAS COPCO WAGNER-

WH WIGGINS LIFT CO., INC.-

WI WILLMAR EQUIPMENT COMPANY-

WL WALKER MANUFACTURING CO., INC.-

WN WAIN-ROY, INC.-

H-13

EP 1110-1-8, Vol. 430 Nov 11

H-14


EP 1110-1-8(Vol. 1)11/30/2011

CODE MANUFACTURER

WO WACO SCAFFOLDING & EQUIPMENT-

WR WARNER FRUEHAUF TRAILER CO., INC.-

WS WHITEMAN CONSPRAY, INC.-

WT WIRTGEN AMERICAN, INC.-

XX NO SPECIFIC MANUFACTURER-

YA YANMAR DIESEL AMERICA CORP.-

YB ADVANCED ENVIRONMENTAL SOLUTIONS-

ZZ GENERIC EQUIPMENT-

H-14

EP 1110-1-8, Vol. 430 Nov 11

H-15


EP 1110-1-8, Vol. 430 Nov 11

H-16

APPENDIX I FEDERAL COST-OF-MONEY RATE

EP 1110-1-8, Vol. 430 Nov 11

I-1

(Renegotiation or Prompt Payment Rate)

APPENDIX IFEDERAL COST-OF-MONEY RATE

EP 1110-1-8(Vol. 8)

11/30/2011

EFFECTIVE DATE RATEEFFECTIVE MONTHS

JULY - DECEMBER 7.000%7/1/1996

JANUARY - JUNE 6.375%1/1/1997


JANUARY - JUNE 6.250%1/1/1998


JANUARY - JUNE 5.000%1/1/1999


JANUARY - JUNE 6.750%1/1/2000


JANUARY - JUNE 6.375%1/1/2001


JANUARY - JUNE 5.500%1/1/2002


JANUARY - JUNE 4.250%1/1/2003


JANUARY - JUNE 4.000%1/1/2004


JANUARY - JUNE 4.250%1/1/2005


JANUARY - JUNE 5.125%1/1/2006


JANUARY - JUNE 5.250%1/1/2007


JANUARY - JUNE 4.750%1/1/2008


JANUARY - JUNE 5.625%1/1/2009


JANUARY - JUNE 3.250%1/1/2010


JANUARY - JUNE 2.625%1/1/2011


I-1

EP 1110-1-8, Vol. 430 Nov 11

I-2

APPENDIX J EQUIPMENT ACCESSORIES

EP 1110-1-8, Vol. 430 Nov 11

J-1

APPENDIX J EQUIPMENT ACCESSORIES

The following accessories are listed by category (CAT), subcategory (SUB), and description (including features required for safety). The accessories have been included with the major equipment listed in this pamphlet when they are not included with the basic cost and are offered by the manufacturer.

CAT SUB DESCRIPTION C85.10 CRANES, DRAGLINE AND CLAMSHELL, CRAWLER MOUNTED Power load lowering Independent swing and travel Third drum Torque converter [machines 1 1/2 cubic yard (cy) or larger] Approximately one-half maximum boom length Counterweight (standard) Fire extinguisher 5-B:C Swing and reverse signal (backup) alarm Boom angle indicator and a load-indicating device Drum rotation indicators Anti-two block (upper limit) devices Manufacturers’ mandatory accessories C85.20 CRANES, LIFTING, CRAWLER MOUNTED Power load lowering Independent swing and travel Third drum Torque converter (machines 25 tons or larger) One-half maximum boom length (machines less than 60 tons) Maximum boom length at 360 degree rating (machines larger than

60 tons) Counterweight (standard) Fire extinguisher 5-B:C Swing and reverse signal (backup) alarm Boom angle indicator and a load-indicating device Drum rotation indicators Anti-two block (upper limit) devices Manufacturers’ mandatory accessories Hook block on machines larger than 100 tons C90.01 TRUCK CRANES - LESS THAN 25 TONS Power load lowering Third drum

EP 1110-1-8, Vol. 430 Nov 11

J-2

CAT SUB DESCRIPTION Mechanical outriggers with screw jacks Maximum boom length at 360 degrees rating C90.01 TRUCK CRANES - LESS THAN 25 TONS (Continued) Counterweight (standard) Fire extinguisher 5-B:C Swing and reverse signal (backup) alarm Boom angle indicator and a load-indicating device Drum rotation indicators Anti-two block (upper limit) devices Manufacturers mandatory accessories C90.02 TRUCK CRANE - 25 TONS AND LARGER C90.03 Power load lowering C90.04 Third drum Hydraulic outriggers with screw jacks Torque converter when available (upper only) Maximum boom length at 360 degrees rating Counterweight (standard) Fire extinguisher 5-B:C Reverse signal (backup) alarm Boom angle indicator and a load-indicating device Drum rotation indicators Anti-two block (upper limit) devices Hook block on machines larger than 100 tons G15 GRADER Rollover protective structures (ROPS) with enclosed cab Ripper/scarifier, rear mounted Front wheel lean Power circle Hydraulic shift and tilt moldboard End bits Standard work lights Fire extinguisher 5-B:C Reverse signal (backup) alarm H25 EXCAVATORS, HYDRAULIC H30 Backhoe bucket (standard) Backhoe stick (medium length) Backhoe boom (one piece) Backhoe bucket linkage (with cylinder) Guards

EP 1110-1-8, Vol. 430 Nov 11

J-3

CAT SUB DESCRIPTION Counterweight Standard work lights Reverse signal (backup) alarm ROPS Fire extinguisher 5-B:C H35 HYDRAULIC SHOVELS - CRAWLER MOUNTED Torque converter (machines 1 1/2 cy or larger) Counterweight Reverse signal (backup) alarm ROPS Fire extinguisher 5-B:C L30 LOADERS, BELT (CONVEYOR BELTS) Power unit Head pulley clutch and backstop Belt cleaner and belt installing equipment King pin attachments L35 LOADERS, 1 1/2 cy AND LARGER L40 Blower fan Guard, power train Automatic bucket positioner Standard counterweight Machines less than 7 cy: General purpose or excavating bucket

with bolt on cutting edge and no teeth Machines 7 cy or larger: Rock bucket with bolt on cutting edge and

teeth Standard work lights Reverse signal (backup) alarm ROPS Fire extinguisher 5-B:C S10 SCRAPERS S15 Control single lever S20 Blower fan Standard work light Guards, power train Reverse signal (backup) alarm ROPS Fire extinguisher 5-B:C Supplemental steering

EP 1110-1-8, Vol. 430 Nov 11

J-4

CAT SUB DESCRIPTION T15 TRACTOR, CRAWLER Hydraulic controls for ripper and blade Guards Blower fan Standard work lights Hook, front pull Track grousers (severe service for units over 200 hp) Counterweights where required Reverse signal (backup) alarm ROPS Universal blade T20 TRACTOR, WHEEL Hydraulic controls for ripper and blade Guards Blower fan Standard work lights Blade Fire extinguisher 5-B:C Counterweights when required T25 TRACTOR, AGRICULTURAL Independent power take off (PTO) Standard work lights Fire extinguisher 5-B:C Counterweights when required 3-point hitch ROPS Hydraulic system with controls T55 TRUCKS, OFF-HIGHWAY No spin differential Tachograph Engine and transmission guards Body liners

EP 1110-1-8, Vol. 430 Nov 11

J-5


EP 1110-1-8, Vol. 430 Nov 11

J-6

APPENDIX K GROUND ENGAGING COMPONENT COSTS INCLUDED IN REPAIRS (RCF)

EP 1110-1-8, Vol. 430 Nov 11

K-1

CATEGORY

SUB DESCRIPTION EK C DC LIFE SLV RCF

Blade cutting edges, wear plates,

hard facing, and end plates

Ground Engaging Component Costs Included in Repairs (RCF)

EP 1110-1-8

11/30/2011(Vol. 8)

APPENDIX K

Bucket teeth, cutting edges,

side cutters, and wear plates

Ripper tips and shank protection

Equipment Specific Wear

Items

B15 0.00 95 A B 8,000 0.10 0.80BROOMS, STREET SWEEPERS & FLUSHERS

B25 0.00 15 A B 8,000 0.10 0.70BUCKETS, CLAMSHELL

B25 0.00 15 S B 6,500 0.10 0.80BUCKETS, CLAMSHELL

B35 0.00 1BUCKETS, DRAGLINE

B35 0.10 15 A B 8,000 0.10 0.70 LIGHT WEIGHT

B35 0.10 15 S B 6,500 0.10 0.80 LIGHT WEIGHT

B35 0.20 15 A B 9,000 0.10 0.70 MEDIUM WEIGHT

B35 0.20 15 S B 7,000 0.10 0.80 MEDIUM WEIGHT

B35 0.30 15 A B 10,000 0.10 0.70 HEAVY WEIGHT

B35 0.30 15 S B 8,000 0.10 0.80 HEAVY WEIGHT

G15 0.00 35 A B 14,500 0.25 0.75GRADERS, MOTOR

G15 0.00 35 S B 13,500 0.25 0.85GRADERS, MOTOR

H25 0.00 1HYDRAULIC EXCAVATORS, CRAWLER MOUNTED

H25 0.10 65 A B 8,000 0.25 0.70 0 LBS THRU 12,500 LBS (COMPACT EXCAVATORS)

H25 0.10 65 S B 7,000 0.25 0.80 0 LBS THRU 12,500 LBS (COMPACT EXCAVATORS)

H25 0.11 65 A B 8,500 0.25 0.70 OVER 12,500 LBS THRU 40,000 LBS

H25 0.11 65 S B 7,000 0.25 0.85 OVER 12,500 LBS THRU 40,000 LBS




L- 1

EK=Economic Key (Appendix E) C=Operating Conditions (A=average, S=severe) DC=Discount Code (B=basic 7.5%, S=special 15%) LIFE=Economic Life SLV=Salvage Value RCF=Repair Cost Factor

Ground Engaging Component (GEC) is defined as those wear items on the machine that come in direct contact with in situ ground to perform the machines primary function. For machines with blades, GEC can include: cutting edges, wear plates, hard facing, and end plates. For machines with buckets, GEC can include: bucket teeth, cutting edges, side cutters, and wear plates. For machines with rippers, GEC can include: tips and shank protectors. Equipment Specific Wear items include those items of wear that are specific to that equipment. Not included in the Repairs and must be added as needed are: drill/bits, drill/steel, roadheader/rock breaking bits, air tools/breaker points/jackhammer points, concrete coring drill bits, and other wear items that are not shown here.

EP 1110-1-8, Vol. 430 Nov 11

K-2

CATEGORY





EP 1110-1-8

11/30/2011(Vol. 8)

APPENDIX K





Items


H25 0.14 65 A B 19,000 0.25 1.10 OVER 160,000 LBS

H25 0.14 65 S B 15,000 0.25 1.25 OVER 160,000 LBS

H30 0.00 1HYDRAULIC EXCAVATORS, WHEEL MOUNTED

H30 0.01 65 A B 8,000 0.25 0.50 0 THRU 1.0 CY

H30 0.01 65 S B 6,500 0.25 0.55 0 THRU 1.0 CY

H30 0.02 65 A B 10,000 0.25 0.60 OVER 1.0 CY

H30 0.02 65 S B 8,000 0.25 0.65 OVER 1.0 CY

H35 0.00 1HYDRAULIC SHOVELS, CRAWLER MOUNTED

H35 0.11 65 A B 14,000 0.20 1.00 DIESEL, 0 CY THRU 5.0 CY

H35 0.11 65 S B 12,000 0.20 1.10 DIESEL, 0 CY THRU 5.0 CY

H35 0.12 65 A B 16,000 0.20 1.20 DIESEL, OVER 5.0 CY

H35 0.12 65 S B 14,000 0.20 1.30 DIESEL, OVER 5.0 CY

H35 0.21 65 A B 18,000 0.20 0.80 ELECTRIC, OVER 2.5 CY

H35 0.21 65 S B 16,000 0.20 0.90 ELECTRIC, OVER 2.5 CY

L35 0.00 40 A B 10,000 0.20 1.10LOADERS, FRONT END, CRAWLER TYPE

L35 0.00 40 S B 8,000 0.20 1.25LOADERS, FRONT END, CRAWLER TYPE

L40 0.00 1LOADERS, FRONT END, WHEEL TYPE

L40 0.11 45 A B 9,250 0.25 0.70 ARTICULATED, 0 THRU 225 HP

L40 0.11 45 S B 8,750 0.25 0.80 ARTICULATED, 0 THRU 225 HP

L- 2



EP 1110-1-8, Vol. 430 Nov 11

K-3

CATEGORY





EP 1110-1-8

11/30/2011(Vol. 8)

APPENDIX K





Items

L40 0.12 45 A B 13,500 0.20 0.70 ARTICULATED, OVER 225 HP

L40 0.12 45 S B 12,000 0.20 0.75 ARTICULATED, OVER 225 HP

L40 0.20 45 A B 8,000 0.20 0.80 SKID STEER

L40 0.31 45 A B 10,000 0.25 0.85 TOOL CARRIER & TELESCOPIC HANDLERS, 0 THRU 225 HP

L40 0.31 45 S B 9,250 0.25 0.90 TOOL CARRIER & TELESCOPIC HANDLERS, 0 THRU 225 HP

L40 0.32 45 A B 12,000 0.15 0.85 TOOL CARRIER & TELESCOPIC HANDLERS, OVER 225 HP

L40 0.32 45 S B 10,000 0.15 0.90 TOOL CARRIER & TELESCOPIC HANDLERS, OVER 225 HP

L45 0.00 40 A B 8,000 0.20 1.35LOADERS / BACKHOE, CRAWLER TYPE

L45 0.00 40 S B 6,000 0.20 1.40LOADERS / BACKHOE, CRAWLER TYPE

L50 0.00 45 A B 10,000 0.25 0.80LOADERS / BACKHOE, WHEEL TYPE

L50 0.00 45 S B 6,000 0.25 0.85LOADERS / BACKHOE, WHEEL TYPE

L60 0.00 75 A B 10,000 0.15 0.70LOG SKIDDERS

L60 0.00 75 S B 8,000 0.15 0.80LOG SKIDDERS

P35 0.00 70 A B 14,000 0.20 0.95PIPELAYERS

P35 0.00 70 S B 11,500 0.20 1.10PIPELAYERS

R30 0.00 1ROLLERS, STATIC, SELF-PROPELLED

R30 0.03 55 A B 12,000 0.20 0.80 TAMPING FOOT, LANDFILL & SOIL COMPACTORS

S10 0.00 1SCRAPERS, ELEVATING

S10 0.01 60 A B 10,000 0.20 0.90 0 THRU 200 HP

S10 0.01 60 S B 8,000 0.20 1.00 0 THRU 200 HP

L- 3



EP 1110-1-8, Vol. 430 Nov 11

K-4

CATEGORY





EP 1110-1-8

11/30/2011(Vol. 8)

APPENDIX K





Items

S10 0.02 60 A B 13,000 0.25 0.95 OVER 200 HP

S10 0.02 60 S B 11,500 0.25 1.00 OVER 200 HP

S15 0.00 60 A B 15,000 0.20 0.80SCRAPERS, CONVENTIONAL

S15 0.00 60 S B 12,500 0.20 0.85SCRAPERS, CONVENTIONAL

S20 0.00 60 A B 15,000 0.20 0.85SCRAPERS, TANDEM POWERED

S20 0.00 60 S B 13,500 0.20 0.90SCRAPERS, TANDEM POWERED

S25 0.00 60 A B 12,000 0.20 0.70SCRAPERS, TRACTOR DRAWN

S25 0.00 60 S B 10,000 0.20 0.75SCRAPERS, TRACTOR DRAWN

T15 0.00 1TRACTORS, CRAWLER (DOZER) (includes blade)

T15 0.01 70 A B 10,000 0.30 1.10 0 THRU 225 HP

T15 0.01 70 S B 8,000 0.30 1.25 0 THRU 225 HP

T15 0.02 70 A B 12,500 0.25 1.20 226 HP THRU 425 HP

T15 0.02 70 S B 10,500 0.25 1.25 226 HP THRU 425 HP

T15 0.03 70 A B 15,000 0.20 1.20 OVER 425 HP

T15 0.03 70 S B 12,500 0.20 1.35 OVER 425 HP

T20 0.00 75 A B 14,000 0.15 0.60TRACTORS, WHEEL TYPE (DOZER)

T20 0.00 75 S B 13,000 0.15 0.65TRACTORS, WHEEL TYPE (DOZER)

L- 4



EP 1110-1-8, Vol. 430 Nov 11

K-5


EP 1110-1-8, Vol. 430 Nov 11

K-6

APPENDIX L GUIDE FOR ESTIMATING DRILL STEEL AND DRILL BIT COSTS

EP 1110-1-8, Vol. 430 Nov 11

L-1

Guide for Estimating Drill Steel and Drill Bit Costs

Prepared for the US Army Corps of Engineers, Walla Walla District By Western Mine Engineering, Inc in cooperation

with Aventurine Engineering, Inc. 2006

August 2006

EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-2

Cost Assumptions for Drill Steel and Drill Bit

General: The approach to defining the scope of this cost guide was to confine the work to the basic drilling process and attendant drill bit and steel lives and costs. This not only simplified the study parameters but also ensured that future users of the study results could readily modify the data to suit their individual needs.

1. The steel costs reflect the cost of drilling steel only. All ancillary equipment such as

couplings, striking bars, and hammer maintenance items were not included.

2. The bit life is indicative of the total life of each bit to include up to 10 sharpenings/grindings per bit. The bit costs, however, are list prices for each bit and do not reflect the costs associated with this process.

3. Costs for both bits and steel are list pricing based on manufacturers’ catalogs or

quotes. No additional materials, equipment costs, or other associated costs are included. No discounts were applied to the catalog list prices. Estimators will have to determine an appropriate discount for their individual cases. All prices are based on current, 2006 costs.

4. The bit and steel lives and penetration rates are based on time the bit is engaged in

the hole. Adjustment for setup, tear down, and moving time between holes has not been considered.

5. Appropriate bits were identified primarily by drill type and then list prices were

determined from manufacturers’ catalogs. All bits were button type; with threaded button bits used for the top hammer percussion drills, down the hole (DTH) button bits for “DTH” drills, and tungsten carbide button, roller bits selected for rotary drills.

6. Large rotary drills often use 20' or longer drilling steel. It was our belief that most

situations Corps of Engineers estimators face will fall in the range of percussion or smaller “DTH” drills. In these instances the 12' rod is appropriate. Cursory review of the costs of longer steel rods suggest that costs for a specific drill steel diameter do not vary dramatically on a per foot basis for longer rods. Therefore, the assumption is made that a direct conversion to cost per rod for longer lengths can be made in proportion to the cost for a 12' length rod. For further information, see the note at the lower right corner of each of the spreadsheets for a detailed procedure to make the conversion for rod length and hole depth.

EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-3

Example of Estimating Drill Steel and Drill Bit Costs

General: The approach is to define the scope of the work and determine an estimated cost for drill steel and bits from the answers to the questions below. Follow the simplified steps to arrive at the estimated costs. Determine parameters:

1. Determine the type of drilling method – percussion, down the hole (DTH), or rotary.

2. Determine the manufacturer and model of drilling equipment or determine

equivalency of equipment used in this guide.

3. Determine the material that will be drilled through.

4. Determine the hole diameter of drill.

5. Determine the length of drill rod required to drill hole to the required depth. Determine costs: (This is an example on how to determine costs)

1. Determine the type of drilling method – down the hole (DTH).

2. Determine the manufacturer/model of drilling equipment – Atlas Copco DM25SP.

3. Determine the material that will be drilled - Basalt .

4. Determine the hole diameter of drill – 5”.

5. Determine the length of drill rod required – 90 feet.

6. Calculate drill steel costs from cost tables:

a. Cost of drill steel $/foot per rod ranges $0.034 to $0.025 will use $0.034.

b. Based on 90’ of drilling at 12’ lengths of drill rod – (90’/12’) = 7.5 rods are required. Round up to next whole number = 8 rods.

c. From drill steel cost adjustment factor chart: for 8 rods the factor is 4.5. d. From instructions: $0.034 X 4.5 = $0.1530/lf of hole drilled.

7. Determine drill bit costs from cost tables – costs range from $0.55 to $0.40/lf.

EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-4

DRILL MODEL - Atlas Copco ROC D5 - percussion

Bit Life (feet/bit) Bit Cost ($/foot)

1.75 2.00 2.50 1.75 2.00 2.50Granite 1,506 - 2,037 1,449 - 1,960 1,359 - 1,838 Granite $0.04 - $0.03 $0.05 - $0.04 $0.07 - $0.05Basalt 674 - 912 649 - 878 608 - 823 Basalt $0.09 - $0.07 $0.11 - $0.08 $0.16 - $0.12Gabbro 1,002 - 1,356 964 - 1,305 904 - 1,223 Gabbro $0.06 - $0.05 $0.07 - $0.05 $0.11 - $0.08Shale 1,427 - 1,931 1,373 - 1,858 1,287 - 1,742 Shale $0.04 - $0.03 $0.05 - $0.04 $0.08 - $0.06Sandstone 524 - 709 504 - 682 473 - 639 Sandstone $0.12 - $0.09 $0.14 - $0.10 $0.21 - $0.15Siltstone 3,779 - 5,112 3,636 - 4,919 3,409 - 4,612 Siltstone $0.02 - $0.01 $0.02 - $0.01 $0.03 - $0.02Conglomer 292 - 395 281 - 380 263 - 356 Conglomer $0.21 - $0.16 $0.25 - $0.18 $0.37 - $0.28Breccia 2,181 - 2,951 2,099 - 2,839 1,968 - 2,662 Breccia $0.03 - $0.02 $0.03 - $0.02 $0.05 - $0.04Limestone 1,835 - 2,483 1,766 - 2,389 1,656 - 2,240 Limestone $0.03 - $0.02 $0.04 - $0.03 $0.06 - $0.04Schist 3,414 - 4,619 3,285 - 4,444 3,080 - 4,167 Schist $0.02 - $0.01 $0.02 - $0.02 $0.03 - $0.02Slate 1,710 - 2,313 1,645 - 2,226 1,542 - 2,087 Slate $0.04 - $0.03 $0.04 - $0.03 $0.06 - $0.05Gneiss 735 - 995 707 - 957 663 - 897 Gneiss $0.08 - $0.06 $0.10 - $0.07 $0.15 - $0.11

Drill Steel Life (feet/rod) Drill Steel Cost ($/foot per rod)

1.75 2.00 2.50 1.75 2.00 2.50Granite 2,720 - 3,680 2,617 - 3,541 2,454 - 3,320 Granite $0.103 - $0.076 $0.107 - $0.079 $0.132 - $0.098Basalt 1,417 - 1,918 1,364 - 1,845 1,279 - 1,730 Basalt $0.198 - $0.146 $0.205 - $0.152 $0.253 - $0.187Gabbro 1,600 - 2,164 1,539 - 2,083 1,443 - 1,953 Gabbro $0.175 - $0.129 $0.182 - $0.134 $0.224 - $0.166Shale 2,855 - 3,863 2,747 - 3,717 2,576 - 3,485 Shale $0.098 - $0.072 $0.102 - $0.075 $0.126 - $0.093Sandstone 2,978 - 4,029 2,865 - 3,877 2,687 - 3,635 Sandstone $0.094 - $0.069 $0.098 - $0.072 $0.121 - $0.089Siltstone 2,964 - 4,011 2,852 - 3,859 2,674 - 3,618 Siltstone $0.094 - $0.070 $0.098 - $0.073 $0.121 - $0.090Conglomer 3,425 - 4,633 3,295 - 4,458 3,090 - 4,180 Conglomer $0.082 - $0.060 $0.085 - $0.063 $0.105 - $0.078Breccia 4,739 - 6,412 4,560 - 6,170 4,276 - 5,785 Breccia $0.059 - $0.044 $0.061 - $0.045 $0.076 - $0.056Limestone 3,931 - 5,318 3,782 - 5,117 3,546 - 4,798 Limestone $0.071 - $0.053 $0.074 - $0.055 $0.091 - $0.068Schist 4,828 - 6,532 4,646 - 6,285 4,356 - 5,893 Schist $0.058 - $0.043 $0.060 - $0.045 $0.074 - $0.055Slate 3,133 - 4,239 3,015 - 4,079 2,827 - 3,824 Slate $0.089 - $0.066 $0.093 - $0.069 $0.115 - $0.085Gneiss 2,849 - 3,855 2,742 - 3,709 2,571 - 3,478 Gneiss $0.098 - $0.073 $0.102 - $0.075 $0.126 - $0.093

(Based on 12 foot drilling rod length.)

Penetration Rate (feet/hour) Drill Steel Cost Adjustment FactorAs this study is based on 12 foot drilling rod length,

1.75 2.00 2.50 Number of rods Factor the total steel cost per foot of hole drilled dependsGranite 98 - 132 83 - 113 64 - 86 upon the total number of 12 foot sections in the hole.Basalt 57 - 77 48 - 65 37 - 50 1 1.0 Divide the total hole length by 12 and round this resultGabbro 63 - 85 53 - 72 41 - 55 2 1.5 up to the next whole number to determine number of Shale 102 - 138 87 - 117 66 - 90 3 2.0 rods required to drill the hole. Adjust this number to theSandstone 105 - 142 90 - 121 69 - 93 4 2.5 average number of rods during drilling by consultingSiltstone 105 - 142 89 - 121 68 - 92 5 3.0 the Drill Steel Cost Adjustment Factor table to the left.Conglomer 118 - 160 101 - 136 77 - 104 6 3.5 Multiply this adjustment factor times the cost per footBreccia 155 - 210 132 - 179 101 - 137 7 4.0 per rod from the table above. The result is the totalLimestone 133 - 180 113 - 153 86 - 117 8 4.5 drill steel cost per foot of hole drilled. Other drillSchist 158 - 213 134 - 181 103 - 139 9 5.0 steel lengths may be adjusted for by determining theSlate 110 - 149 94 - 127 72 - 97 10 5.5 total length of rods required and then converting that Gneiss 102 - 137 86 - 117 66 - 89 n (n+1)/2 to the number of equivalent 12 foot sections. Once

this is determined follow the procedure outlined above.

Prepared by Western Mine Division, InfoMine USA, Inc. in cooperation with Aventurine Engineering, Inc. 2006

Hole Diameter (inches)





EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-5

DRILL MODEL - Atlas Copco ROC D7 - percussion


2.50 3.00 4.00 2.50 3.00 4.00Granite 1,203 - 1,628 1,115 - 1,509 1,050 - 1,421 Granite $0.08 - $0.06 $0.12 - $0.09 $0.21 - $0.16Basalt 539 - 729 499 - 676 470 - 636 Basalt $0.18 - $0.13 $0.26 - $0.19 $0.47 - $0.35Gabbro 801 - 1,083 742 - 1,004 699 - 946 Gabbro $0.12 - $0.09 $0.18 - $0.13 $0.32 - $0.24Shale 1,140 - 1,542 1,057 - 1,430 995 - 1,347 Shale $0.09 - $0.06 $0.12 - $0.09 $0.22 - $0.17Sandstone 418 - 566 388 - 525 365 - 494 Sandstone $0.23 - $0.17 $0.34 - $0.25 $0.61 - $0.45Siltstone 3,019 - 4,084 2,798 - 3,786 2,636 - 3,566 Siltstone $0.03 - $0.02 $0.05 - $0.03 $0.08 - $0.06Conglomer 233 - 315 216 - 292 204 - 275 Conglomer $0.42 - $0.31 $0.61 - $0.45 $1.10 - $0.81Breccia 1,742 - 2,357 1,615 - 2,186 1,521 - 2,058 Breccia $0.06 - $0.04 $0.08 - $0.06 $0.15 - $0.11Limestone 1,466 - 1,983 1,359 - 1,839 1,280 - 1,732 Limestone $0.07 - $0.05 $0.10 - $0.07 $0.17 - $0.13Schist 2,727 - 3,690 2,528 - 3,421 2,381 - 3,222 Schist $0.04 - $0.03 $0.05 - $0.04 $0.09 - $0.07Slate 1,366 - 1,848 1,266 - 1,713 1,193 - 1,613 Slate $0.07 - $0.05 $0.10 - $0.08 $0.19 - $0.14Gneiss 587 - 795 544 - 737 513 - 694 Gneiss $0.17 - $0.12 $0.24 - $0.18 $0.43 - $0.32


2.50 3.00 4.00 2.50 3.00 4.00Granite 2,173 - 2,940 2,014 - 2,725 1,897 - 2,567 Granite $0.129 - $0.095 $0.161 - $0.119 $0.215 - $0.159Basalt 1,132 - 1,532 1,050 - 1,420 989 - 1,338 Basalt $0.247 - $0.183 $0.309 - $0.228 $0.412 - $0.304Gabbro 1,278 - 1,729 1,185 - 1,603 1,116 - 1,510 Gabbro $0.219 - $0.162 $0.273 - $0.202 $0.365 - $0.270Shale 2,281 - 3,086 2,115 - 2,861 1,992 - 2,695 Shale $0.123 - $0.091 $0.153 - $0.113 $0.204 - $0.151Sandstone 2,379 - 3,218 2,205 - 2,984 2,077 - 2,810 Sandstone $0.118 - $0.087 $0.147 - $0.109 $0.196 - $0.145Siltstone 2,368 - 3,204 2,195 - 2,970 2,068 - 2,798 Siltstone $0.118 - $0.087 $0.148 - $0.109 $0.197 - $0.145Conglomer 2,736 - 3,701 2,536 - 3,431 2,389 - 3,232 Conglomer $0.102 - $0.076 $0.128 - $0.094 $0.170 - $0.126Breccia 3,786 - 5,122 3,510 - 4,749 3,306 - 4,473 Breccia $0.074 - $0.055 $0.092 - $0.068 $0.123 - $0.091Limestone 3,140 - 4,249 2,911 - 3,939 2,742 - 3,710 Limestone $0.089 - $0.066 $0.111 - $0.082 $0.148 - $0.110Schist 3,857 - 5,218 3,576 - 4,838 3,368 - 4,556 Schist $0.073 - $0.054 $0.091 - $0.067 $0.121 - $0.089Slate 2,503 - 3,386 2,320 - 3,139 2,185 - 2,957 Slate $0.112 - $0.083 $0.140 - $0.103 $0.186 - $0.138Gneiss 2,276 - 3,080 2,110 - 2,855 1,987 - 2,689 Gneiss $0.123 - $0.091 $0.154 - $0.113 $0.205 - $0.151

(Based on12 foot drilling rod length.)










EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-6

DRILL MODEL - Atlas Copco ECM590 - percussion


2.50 3.50 4.50 2.50 3.50 4.50Granite 1,168 - 1,580 1,060 - 1,434 986 - 1,334 Granite $0.08 - $0.06 $0.15 - $0.11 $0.27 - $0.20Basalt 523 - 708 475 - 642 441 - 597 Basalt $0.19 - $0.14 $0.34 - $0.25 $0.61 - $0.45Gabbro 778 - 1,052 706 - 955 656 - 888 Gabbro $0.13 - $0.09 $0.23 - $0.17 $0.41 - $0.30Shale 1,107 - 1,498 1,005 - 1,359 934 - 1,264 Shale $0.09 - $0.07 $0.16 - $0.12 $0.29 - $0.21Sandstone 406 - 550 369 - 499 343 - 464 Sandstone $0.24 - $0.18 $0.43 - $0.32 $0.78 - $0.58Siltstone 2,931 - 3,966 2,660 - 3,599 2,474 - 3,347 Siltstone $0.03 - $0.02 $0.06 - $0.04 $0.11 - $0.08Conglomer 226 - 306 205 - 278 191 - 259 Conglomer $0.43 - $0.32 $0.77 - $0.57 $1.40 - $1.04Breccia 1,692 - 2,289 1,535 - 2,077 1,428 - 1,932 Breccia $0.06 - $0.04 $0.10 - $0.08 $0.19 - $0.14Limestone 1,424 - 1,926 1,292 - 1,748 1,201 - 1,626 Limestone $0.07 - $0.05 $0.12 - $0.09 $0.22 - $0.16Schist 2,648 - 3,583 2,403 - 3,251 2,235 - 3,024 Schist $0.04 - $0.03 $0.07 - $0.05 $0.12 - $0.09Slate 1,326 - 1,794 1,203 - 1,628 1,119 - 1,514 Slate $0.07 - $0.05 $0.13 - $0.10 $0.24 - $0.18Gneiss 570 - 771 517 - 700 481 - 651 Gneiss $0.17 - $0.13 $0.31 - $0.23 $0.56 - $0.41


2.50 3.50 4.50 2.50 3.50 4.50Granite 2,110 - 2,855 1,915 - 2,590 1,781 - 2,409 Granite $0.154 - $0.114 $0.213 - $0.157 $0.229 - $0.169Basalt 1,100 - 1,488 998 - 1,350 928 - 1,255 Basalt $0.295 - $0.218 $0.408 - $0.302 $0.439 - $0.324Gabbro 1,241 - 1,679 1,126 - 1,524 1,047 - 1,417 Gabbro $0.261 - $0.193 $0.361 - $0.267 $0.389 - $0.287Shale 2,215 - 2,997 2,010 - 2,719 1,869 - 2,529 Shale $0.146 - $0.108 $0.202 - $0.150 $0.218 - $0.161Sandstone 2,310 - 3,125 2,096 - 2,836 1,950 - 2,638 Sandstone $0.140 - $0.104 $0.194 - $0.144 $0.209 - $0.154Siltstone 2,300 - 3,111 2,087 - 2,823 1,941 - 2,626 Siltstone $0.141 - $0.104 $0.195 - $0.144 $0.210 - $0.155Conglomer 2,657 - 3,594 2,411 - 3,262 2,242 - 3,033 Conglomer $0.122 - $0.090 $0.169 - $0.125 $0.182 - $0.134Breccia 3,676 - 4,974 3,336 - 4,514 3,103 - 4,198 Breccia $0.088 - $0.065 $0.122 - $0.090 $0.131 - $0.097Limestone 3,049 - 4,125 2,767 - 3,744 2,573 - 3,482 Limestone $0.106 - $0.079 $0.147 - $0.109 $0.158 - $0.117Schist 3,745 - 5,067 3,399 - 4,598 3,161 - 4,277 Schist $0.087 - $0.064 $0.120 - $0.089 $0.129 - $0.095Slate 2,430 - 3,288 2,205 - 2,984 2,051 - 2,775 Slate $0.133 - $0.099 $0.185 - $0.136 $0.198 - $0.147Gneiss 2,210 - 2,990 2,006 - 2,714 1,865 - 2,524 Gneiss $0.147 - $0.108 $0.203 - $0.150 $0.218 - $0.161

(Based pm 12 foot drilling rod length.)










EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-7

DRILL MODEL - Atlas Copco ECM720 - percussion


4.00 4.50 5.00 4.00 4.50 5.00Granite 2,305 - 3,118 2,228 - 3,014 2,161 - 2,924 Granite $0.10 - $0.07 $0.12 - $0.09 $0.15 - $0.11Basalt 1,032 - 1,396 997 - 1,349 967 - 1,309 Basalt $0.22 - $0.16 $0.27 - $0.20 $0.33 - $0.25Gabbro 1,534 - 2,075 1,483 - 2,006 1,438 - 1,946 Gabbro $0.15 - $0.11 $0.18 - $0.13 $0.22 - $0.16Shale 2,184 - 2,955 2,111 - 2,856 2,048 - 2,771 Shale $0.10 - $0.08 $0.13 - $0.09 $0.16 - $0.12Sandstone 802 - 1,085 775 - 1,048 752 - 1,017 Sandstone $0.28 - $0.21 $0.35 - $0.26 $0.43 - $0.32Siltstone 5,783 - 7,824 5,589 - 7,562 5,422 - 7,336 Siltstone $0.04 - $0.03 $0.05 - $0.04 $0.06 - $0.04Conglomer 447 - 604 432 - 584 419 - 567 Conglomer $0.50 - $0.37 $0.62 - $0.46 $0.77 - $0.57Breccia 3,338 - 4,516 3,227 - 4,365 3,130 - 4,235 Breccia $0.07 - $0.05 $0.08 - $0.06 $0.10 - $0.08Limestone 2,809 - 3,800 2,715 - 3,673 2,633 - 3,563 Limestone $0.08 - $0.06 $0.10 - $0.07 $0.12 - $0.09Schist 5,225 - 7,069 5,050 - 6,833 4,899 - 6,628 Schist $0.04 - $0.03 $0.05 - $0.04 $0.07 - $0.05Slate 2,617 - 3,540 2,529 - 3,422 2,453 - 3,319 Slate $0.09 - $0.06 $0.11 - $0.08 $0.13 - $0.10Gneiss 1,125 - 1,522 1,087 - 1,471 1,055 - 1,427 Gneiss $0.20 - $0.15 $0.25 - $0.18 $0.30 - $0.22













EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-8

DRILL MODEL - Atlas Copco DM25SP - DTH


3.50 5.00 6.50 3.50 5.00 6.50Granite 2,498 - 3,380 2,254 - 3,049 2,089 - 2,827 Granite $0.16 - $0.12 $0.24 - $0.18 $0.31 - $0.23Basalt 1,118 - 1,513 1,009 - 1,365 935 - 1,266 Basalt $0.37 - $0.27 $0.55 - $0.40 $0.68 - $0.51Gabbro 1,663 - 2,250 1,500 - 2,030 1,391 - 1,882 Gabbro $0.25 - $0.18 $0.37 - $0.27 $0.46 - $0.34Shale 2,367 - 3,203 2,136 - 2,890 1,980 - 2,679 Shale $0.17 - $0.13 $0.26 - $0.19 $0.32 - $0.24Sandstone 869 - 1,176 784 - 1,061 727 - 983 Sandstone $0.47 - $0.35 $0.70 - $0.52 $0.88 - $0.65Siltstone 6,268 - 8,481 5,655 - 7,651 5,243 - 7,093 Siltstone $0.07 - $0.05 $0.10 - $0.07 $0.12 - $0.09Conglomer 484 - 655 437 - 591 405 - 548 Conglomer $0.85 - $0.63 $1.26 - $0.93 $1.58 - $1.17Breccia 3,618 - 4,896 3,265 - 4,417 3,026 - 4,095 Breccia $0.11 - $0.08 $0.17 - $0.12 $0.21 - $0.16Limestone 3,044 - 4,119 2,747 - 3,716 2,546 - 3,445 Limestone $0.13 - $0.10 $0.20 - $0.15 $0.25 - $0.19Schist 5,664 - 7,663 5,110 - 6,913 4,737 - 6,409 Schist $0.07 - $0.05 $0.11 - $0.08 $0.14 - $0.10Slate 2,836 - 3,837 2,559 - 3,462 2,372 - 3,209 Slate $0.14 - $0.11 $0.21 - $0.16 $0.27 - $0.20Gneiss 1,219 - 1,650 1,100 - 1,489 1,020 - 1,380 Gneiss $0.34 - $0.25 $0.50 - $0.37 $0.63 - $0.46













EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-9

DRILL MODEL - Atlas Copco DM30 -DTH


5.50 6.00 6.50 5.50 6.00 6.50Granite 1,946 - 2,633 1,898 - 2,568 1,855 - 2,509 Granite $0.30 - $0.22 $0.33 - $0.25 $0.35 - $0.26Basalt 871 - 1,179 850 - 1,150 830 - 1,124 Basalt $0.66 - $0.49 $0.74 - $0.55 $0.77 - $0.57Gabbro 1,296 - 1,753 1,263 - 1,709 1,235 - 1,670 Gabbro $0.44 - $0.33 $0.50 - $0.37 $0.52 - $0.38Shale 1,845 - 2,496 1,799 - 2,434 1,758 - 2,378 Shale $0.31 - $0.23 $0.35 - $0.26 $0.36 - $0.27Sandstone 677 - 916 660 - 893 645 - 873 Sandstone $0.85 - $0.63 $0.95 - $0.71 $0.99 - $0.73Siltstone 4,884 - 6,608 4,763 - 6,444 4,654 - 6,297 Siltstone $0.12 - $0.09 $0.13 - $0.10 $0.14 - $0.10Conglomer 377 - 510 368 - 498 360 - 486 Conglomer $1.52 - $1.13 $1.71 - $1.27 $1.78 - $1.32Breccia 2,819 - 3,814 2,749 - 3,720 2,687 - 3,635 Breccia $0.20 - $0.15 $0.23 - $0.17 $0.24 - $0.18Limestone 2,372 - 3,209 2,313 - 3,130 2,260 - 3,058 Limestone $0.24 - $0.18 $0.27 - $0.20 $0.28 - $0.21Schist 4,413 - 5,970 4,303 - 5,822 4,205 - 5,689 Schist $0.13 - $0.10 $0.15 - $0.11 $0.15 - $0.11Slate 2,210 - 2,990 2,155 - 2,916 2,106 - 2,849 Slate $0.26 - $0.19 $0.29 - $0.22 $0.30 - $0.22Gneiss 950 - 1,285 927 - 1,254 905 - 1,225 Gneiss $0.61 - $0.45 $0.68 - $0.50 $0.71 - $0.52













EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-10

DRILL MODEL - Atlas Copco DM45 -DTH


5.00 6.50 8.00 5.00 6.50 8.00Granite 2,580 - 3,490 2,392 - 3,236 2,253 - 3,048 Granite $0.21 - $0.16 $0.27 - $0.20 $0.55 - $0.40Basalt 1,155 - 1,563 1,071 - 1,449 1,009 - 1,364 Basalt $0.48 - $0.35 $0.60 - $0.44 $1.22 - $0.90Gabbro 1,717 - 2,323 1,592 - 2,154 1,499 - 2,029 Gabbro $0.32 - $0.24 $0.40 - $0.30 $0.82 - $0.61Shale 2,445 - 3,308 2,267 - 3,067 2,135 - 2,888 Shale $0.22 - $0.17 $0.28 - $0.21 $0.58 - $0.43Sandstone 897 - 1,214 832 - 1,126 784 - 1,060 Sandstone $0.61 - $0.45 $0.77 - $0.57 $1.57 - $1.16Siltstone 6,473 - 8,758 6,001 - 8,120 5,652 - 7,647 Siltstone $0.08 - $0.06 $0.11 - $0.08 $0.22 - $0.16Conglomer 500 - 677 464 - 627 437 - 591 Conglomer $1.10 - $0.81 $1.38 - $1.02 $2.82 - $2.08Breccia 3,737 - 5,056 3,464 - 4,687 3,263 - 4,414 Breccia $0.15 - $0.11 $0.18 - $0.14 $0.38 - $0.28Limestone 3,144 - 4,254 2,915 - 3,944 2,745 - 3,714 Limestone $0.17 - $0.13 $0.22 - $0.16 $0.45 - $0.33Schist 5,849 - 7,913 5,422 - 7,336 5,107 - 6,910 Schist $0.09 - $0.07 $0.12 - $0.09 $0.24 - $0.18Slate 2,929 - 3,963 2,715 - 3,674 2,557 - 3,460 Slate $0.19 - $0.14 $0.24 - $0.17 $0.48 - $0.36Gneiss 1,259 - 1,704 1,168 - 1,580 1,100 - 1,488 Gneiss $0.44 - $0.32 $0.55 - $0.41 $1.12 - $0.83













EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-11

DRILL MODEL - Atlas Copco DM M2 -DTH


8.88 10.00 11.875 8.88 10.00 11.875Granite 1,779 - 2,407 1,719 - 2,325 1,636 - 2,213 Granite $0.78 - $0.58 $1.11 - $0.82 $2.75 - $2.03Basalt 796 - 1,078 770 - 1,041 732 - 991 Basalt $1.74 - $1.29 $2.47 - $1.82 $6.15 - $4.54Gabbro 1,184 - 1,602 1,144 - 1,548 1,089 - 1,473 Gabbro $1.17 - $0.86 $1.66 - $1.23 $4.13 - $3.06Shale 1,686 - 2,281 1,629 - 2,204 1,550 - 2,097 Shale $0.82 - $0.61 $1.17 - $0.86 $2.90 - $2.15Sandstone 619 - 837 598 - 809 569 - 770 Sandstone $2.24 - $1.65 $3.18 - $2.35 $7.91 - $5.85Siltstone 4,464 - 6,039 4,313 - 5,835 4,104 - 5,553 Siltstone $0.31 - $0.23 $0.44 - $0.33 $1.10 - $0.81Conglomer 345 - 467 333 - 451 317 - 429 Conglomer $4.02 - $2.97 $5.70 - $4.22 $14.19 - $10.49Breccia 2,577 - 3,486 2,490 - 3,368 2,369 - 3,205 Breccia $0.54 - $0.40 $0.76 - $0.56 $1.90 - $1.40Limestone 2,168 - 2,933 2,095 - 2,834 1,993 - 2,697 Limestone $0.64 - $0.47 $0.91 - $0.67 $2.26 - $1.67Schist 4,033 - 5,457 3,897 - 5,272 3,708 - 5,017 Schist $0.34 - $0.25 $0.49 - $0.36 $1.21 - $0.90Slate 2,020 - 2,733 1,951 - 2,640 1,857 - 2,512 Slate $0.69 - $0.51 $0.97 - $0.72 $2.42 - $1.79Gneiss 868 - 1,175 839 - 1,135 798 - 1,080 Gneiss $1.59 - $1.18 $2.26 - $1.67 $5.64 - $4.17













EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-12

DRILL MODEL - Atlas Copco DM25SP - Rotary















EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-13

DRILL MODEL - Atlas Copco DM30 -Rotary















EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-14

DRILL MODEL - Atlas Copco DM45 -Rotary















EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-15

DRILL MODEL - Atlas Copco DM M2 -Rotary















EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-16

DRILL MODEL - Bucyrus International 59R -Rotary


12.25 15.00 16.00 12.25 15.00 16.00Granite 3379.984 - 4572.919 3213.372 - 4347.504 3162.023 - 4278.031 Granite $1.95 - $1.44 $3.23 - $2.38 $3.48 - $2.58Basalt 1770.653 - 2395.589 1683.371 - 2277.502 1656.471 - 2241.108 Basalt $3.73 - $2.76 $6.16 - $4.55 $6.65 - $4.92Gabbro 1996.573 - 2701.246 1898.155 - 2568.092 1867.823 - 2527.054 Gabbro $3.31 - $2.44 $5.46 - $4.04 $5.90 - $4.36Shale 3546.993 - 4798.873 3372.149 - 4562.319 3318.263 - 4489.414 Shale $1.86 - $1.38 $3.07 - $2.27 $3.32 - $2.45Sandstone 3697.769 - 5002.863 3515.492 - 4756.254 3459.315 - 4680.25 Sandstone $1.79 - $1.32 $2.95 - $2.18 $3.18 - $2.35Siltstone 3681.304 - 4980.588 3499.839 - 4735.076 3443.912 - 4659.411 Siltstone $1.79 - $1.33 $2.96 - $2.19 $3.20 - $2.36Conglomer 4247.818 - 5747.048 4038.427 - 5463.755 3973.894 - 5376.445 Conglomer $1.55 - $1.15 $2.57 - $1.90 $2.77 - $2.05Breccia 5863.339 - 7932.753 5574.314 - 7541.719 5485.238 - 7421.204 Breccia $1.13 - $0.83 $1.86 - $1.37 $2.01 - $1.48Limestone 4870.335 - 6589.277 4630.259 - 6264.468 4556.268 - 6164.363 Limestone $1.36 - $1.00 $2.24 - $1.65 $2.42 - $1.79Schist 5972.24 - 8080.09 5677.846 - 7681.792 5587.116 - 7559.039 Schist $1.11 - $0.82 $1.83 - $1.35 $1.97 - $1.46Slate 3888.976 - 5261.555 3697.274 - 5002.194 3638.192 - 4922.26 Slate $1.70 - $1.25 $2.80 - $2.07 $3.03 - $2.24Gneiss 3539.394 - 4788.591 3364.924 - 4552.544 3311.153 - 4479.796 Gneiss $1.87 - $1.38 $3.08 - $2.28 $3.33 - $2.46


12.25 15.00 16.00 12.25 15.00 16.00Granite 41969.55 - 56782.33 39900.72 - 53983.32 39263.11 - 53120.68 Granite $0.078 - $0.058 $0.082 - $0.061 $0.083 - $0.062Basalt 24574.25 - 33247.51 23362.89 - 31608.62 22989.56 - 31103.52 Basalt $0.133 - $0.098 $0.140 - $0.104 $0.142 - $0.105Gabbro 27142.87 - 36722.71 25804.9 - 34912.52 25392.55 - 34354.62 Gabbro $0.121 - $0.089 $0.127 - $0.094 $0.129 - $0.095Shale 43679.22 - 59095.42 41526.11 - 56182.39 40862.54 - 55284.61 Shale $0.075 - $0.055 $0.079 - $0.058 $0.080 - $0.059Sandstone 45210.83 - 61167.6 42982.23 - 58152.42 42295.38 - 57223.16 Sandstone $0.072 - $0.054 $0.076 - $0.056 $0.077 - $0.057Siltstone 45044.11 - 60942.03 42823.72 - 57937.98 42139.41 - 57012.14 Siltstone $0.073 - $0.054 $0.076 - $0.056 $0.078 - $0.057Conglomer 50711.07 - 68609.09 48211.33 - 65227.1 47440.93 - 64184.78 Conglomer $0.065 - $0.048 $0.068 - $0.050 $0.069 - $0.051Breccia 66219.99 - 89591.75 62955.76 - 85175.45 61949.75 - 83814.36 Breccia $0.049 - $0.037 $0.052 - $0.038 $0.053 - $0.039Limestone 56790.17 - 76833.76 53990.78 - 73046.35 53128.02 - 71879.08 Limestone $0.058 - $0.043 $0.061 - $0.045 $0.062 - $0.046Schist 67236.6 - 90967.16 63922.26 - 86483.06 62900.8 - 85101.08 Schist $0.049 - $0.036 $0.051 - $0.038 $0.052 - $0.038Slate 47137.81 - 63774.69 44814.22 - 60631 44098.1 - 59662.13 Slate $0.069 - $0.051 $0.073 - $0.054 $0.074 - $0.055Gneiss 43601.73 - 58990.58 41452.44 - 56082.72 40790.04 - 55186.53 Gneiss $0.075 - $0.055 $0.079 - $0.058 $0.080 - $0.059



12.25 15.00 16.00 Number of rods Factor the total steel cost per foot of hole drilled dependsGranite 19.00236 - 25.70907 12.60139 - 17.04894 11.05531 - 14.95719 upon the total number of 12 foot sections in the hole.Basalt 11.03265 - 14.92652 7.316286 - 9.898504 6.418644 - 8.684048 1 1.0 Divide the total hole length by 12 and round this resultGabbro 12.205 - 16.51264 8.093728 - 10.95034 7.100701 - 9.606831 2 1.5 up to the next whole number to determine number of Shale 19.78892 - 26.77325 13.123 - 17.75464 11.51293 - 15.57631 3 2.0 rods required to drill the hole. Adjust this number to theSandstone 20.49398 - 27.72715 13.59055 - 18.38722 11.92312 - 16.13128 4 2.5 average number of rods during drilling by consultingSiltstone 20.41721 - 27.62329 13.53965 - 18.31835 11.87846 - 16.07085 5 3.0 the Drill Steel Cost Adjustment Factor table to the left.Conglomer 23.02897 - 31.15684 15.27163 - 20.66162 13.39794 - 18.12663 6 3.5 Multiply this adjustment factor times the cost per footBreccia 30.19898 - 40.85745 20.02642 - 27.09456 17.56936 - 23.77031 7 4.0 per rod from the table above. The result is the totalLimestone 25.83581 - 34.95433 17.13298 - 23.17992 15.03092 - 20.33595 8 4.5 drill steel cost per foot of hole drilled. Other drillSchist 30.66998 - 41.49468 20.33876 - 27.51714 17.84338 - 24.14104 9 5.0 steel lengths may be adjusted for by determining theSlate 21.38157 - 28.92801 14.17916 - 19.18357 12.43951 - 16.82992 10 5.5 total length of rods required and then converting that Gneiss 19.75326 - 26.725 13.09935 - 17.72265 11.49218 - 15.54824 n (n+1)/2 to the number of equivalent 12 foot sections. Once








EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-17

DRILL MODEL - Atlas Copco TBH4 - Rotary















EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-18

Drill Bits Drill Rod

Bit Type Bit Size Bit Price Rod Type Rod Size Rod Price Button - drop center Percussion rod - 12 ft

1-3/4" $62 R32 $2802" $69 T38 $3242-1.2" $98 T45 $4073" $131 T51 $5683-1.2" $1594" $223 DTH rod - 9'10"4-1.2" $268 3.0 76mm $3845" $321 3.5 89mm $431

4.0 102mm $491 DTH - concave face 4.5 114mm $592

3-1/2" $410 5.5 140mm $8155" $5505-1/2" $575 Rotary rod - 25' to 30'6" $630 4" x 25' $3,3006-1/2" $640 5" x 25' $3,9008" $1,230 7" x 30' $6,9008-7/8" $1,385 8-5/8" x 30' $6,80010" $1,900 10-3/4" x 27.5 $7,50011-/7/8 $4,500

TRICONE - carbide insert3-7/8" $1,1505" $1,6295-1/2" $1,972 All unit prices are manufacturer6" $2,131 list prices. Discounts or 6-1/4" $2,207 premiums may apply depending6-3/4" $2,463 upon market conditions.7-7/8" $3,0239" $3,5899-7/8" $4,78711" $5,64012-1/4" $6,60315" $10,36716" $11,016

BIT AND DRILL STEEL PRICE DATABASE Effective date - 8/2006


EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-19

ROTARY BLASTHOLE DRILLS

Bucyrus manufactures electric rotary blasthole drills with the most innovative features on the market, including programmed drill control, rack and pinion pull-down, hydrostatic propel drives and more. Contact us today for more information about any of our performance-packed drills!

59R Max. hole size: 444 mm (17-1/2 in) Max. bit loading: 74,830 kg (165,000 lbs) Working weight: 183,673 kg (405,000 lbs)

49RIII Max. hole size: 406 mm (16 in) Max. bit loading: 63,975 kg (141,000 lbs) Working weight: 154,224 kg (340,000 lbs)

39HR Max. hole size: 349 mm (13-3/4 in) Max. bit loading: 55,000 kg (122,000 lbs) Working weight: 122,500 kg (270,000 lbs)

35HR Series Max. hole size: 270 mm (10-5/8 in) Max. bit loading: 34,000 kg (75,000 lbs) Working weight: 54,432 kg (120,000 lbs)

EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-20

Drilling Solutions

Ingersoll-Rand has been in the drilling business since Simon Ingersoll invented his first rock drill in 1871. This innovative piece of machinery revolutionized the drilling industry and set the pace for the company's future.

Ingersoll-Rand drills are designed and manufactured to a stringent set of quality standards, assuring you of the most efficient and reliable drills available anywhere.

Now in our second century, we are proud of the comprehensive line of Ingersoll-Rand drilling equipment for the mining, exploration, oil and gas, quarry and water well industries around the world.

Drilling Solutions Blasthole Drills Rotary Large Mid-range Hydraulic Crawle Pneumatic Crawl DHD Drill Selector Waterwell Drills Exploration Drills Gas & Oil / Coal BedDrills

Drilling Accessories Down Hole Drills Threaded Access Hollow Anchor Syst Literature Split Set Products Aftermarket Upgrades Kits Product Upgrad Maintenance Up Promotions Maintenance Sche Service New Product Events Calendar Authorized Distribut Used Equipment Federal Governmen Contact Us Training Schedule

Copyright © 1996-2001 Ingersoll-Rand Company. All rights reserved. Ingersoll-Rand Worldwide Headquarters 200 Chestnut Ridge Road Woodcliff Lake, NJ 07675 USA

HOME BACK

EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-21

EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-22

Select Model:

T4BHDM25/SP

DM30DM45/LPDM50/LPDM-L/LPDM45/SPDM-LSPDM-M2DM-M3DM-H2

351

Rotary - DM45/LP

The DM45/LP is a hydraulic rotary head drive, multi-pass, crawler-mounted drill rig with a 45,000 lb. (20,400 kg) bit load capacity. The standard two-motor spur gear rotary head is rated from 9,000 ft-lb. (12,204 N-m) at 0-100 RPM and 5,400 ft-lb. (732 N-m) at 0-160 RPM. The DM45/LP can drill from 5-1/8 to 7-7/8 in. (130 to 200 mm) diameter blastholes to depths of 180 ft. (55 m) with a 30 ft. (9.1 m) drill pipe change. Two low-pressure Ingersoll-Rand compressor options are available with your choice of Caterpillar or Cummins engines.

[ SPECS ] [ FEATURES ] [ LITERATURE ]

Nominal Hole DiameterDiameter 6-8 in.

Power PackEngine #1 Cummins QSX15 (425 HP @ 1800 rpm)

Compressor #1 900 @ 110 CFM @ PSI / 25.5 @ 758 m3/min@kPA

Engine #2 CAT C15 (425 HP @ 1800 RPM)


Engine #3 Cummins QSX15 (475 HP @ 1800 RPM)


Engine #4 Cat C15 (475 HP @ 1800 RPM)


Rotation

Type 2-motor variable displacement, high torque/high speed

Head Torque High torque: 9,000 ft-lb @ 100 rpm Speed High speed: 5,400 ft-lb @ 160 rpm rpm

Feed System

Type Hydraulic cyls. w/cable pulldown & chain pullback

Bit Load 45,000 lb / 20,411 kg Tower

Pipe Length 30 ft. / 9.1 m.

Fabrication 4-member open front w/rectangular hollow steel tubing/double cut lacing

UndercarriageModel Caterpillar 325L or equivalent



EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-23

Length 15.3 ft. / 4.66 m Carousel

Capacity Capable of 180 ft. Options

Option #1 Contact your local IR distributor for a complete list of options.

Weight & DimensionsHeight (Tower Up) 43 ft. / 13.11 m

Approx. Working Weight 77,000 - 85,000 lbs. / 34,900 - 38,600 kg. Material To Be Drilled

Soft Yes Drill Application

Mining Yes Quarry Yes

Drilling MethodRotary Yes


HOME BACK

EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-24

Select Model:

T4BHDM25/SP


351

Rotary - DM30

The DM30 is a hydraulic tophead drive, multi-pass, crawler-mounted drill rig designed for blastholes ranging from 5-1/8 to 6-3/4 in. (130 to 171 mm) in diameter. On-board depth capability is up to 150 ft. (45.7 m). For rotary drilling, the DM30 can assert a bit load force up to 30,000 lb. (13,608 kg) and rotation speeds of 0-130 RPM. This rig can also be used with downhole drills when equipped with a high-pressure air compressor option.



Power PackEngine #1 Cummins QSX15 (525 HP @ 1800 RPM)

Compressor #1 IR HR2 900/350 CFM @ PSI / 25.5/2,413 m3/min@kPA




Compressor #3 IR WW226 900/110 CFM @ PSI / 25.5/758 m3/min@kPA



Floating Sub Base Isolates components from drilling and propel shock loads/maintains alignment

RotationType Rotary Tophead

Head Torque 5,400 ft-lb. / 7,322 N-m Speed 0-100 rpm

Feed SystemType Single cylinder, cable feed

Bit Load 30,000 lb / (13,608) kg Tower


Construction 4 member open front with hollow steel tubing.



EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-25

UndercarriageManufacturer Caterpillar

Options


Weight & DimensionsHeight (Tower Up) 44.3 ft. / 13.4 m

Approx. Working Weight 68,000 lbs. / 30,844 kg. Material To Be Drilled

Hard Yes Medium Yes



Drilling MethodRotary Yes DHD Yes


HOME BACK

EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-26

Select Model:

T4BHDM25/SP


351

Rotary - DM25/SP

The DM25SP is a crawler-mounted rotary table drill rig designed for single-pass blasthole drilling to depths of up to 50 ft. (15.2 m) and diameters of 3-1/2 to 6-3/4 in. (89 to 171 mm). This drill is capable of rotary drilling with 25,000 lb. (11,340 kg) of bit load at 0-200 rpm. The DM25SP can also be used with downhole drills when equipped with a high-pressure air compressor option.




Compressor #1 900/350 CFM @ PSI / 25.5/2,413 m3/min@kPA




Compressor #3 900/110 CFM @ PSI / 25.5/758 m3/min@kPA



RotationType Rotary Table Drive

Speed 0-170 rpm Torque 3,500 / (4,746 N-m)

Feed SystemType Heavy-duty chains through cluster sprocket

Pulldown 25,000 lbs. / 11,340 kg. Tower

Construction 4 main member, open front, rectangular steel tubing

#1 Single pass depth 40 ft. / 12.2 m. #2 Single pass depth 50 ft. / 15.2 m.

Undercarriage



EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-27

Type Excavator Options


Weight & Dimensions

Weight Varies according to drill pipe: 60,000 - 62,000 lb / 27,216-28,123 kg

Material To Be DrilledHard Yes

Medium Yes Soft Yes

Drill ApplicationQuarry Yes



HOME BACK

EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-28

Select Model:

T4BHDM25/SP


351

Rotary - DM-M2

Designed for rotary or downhole drilling of up to 10-5/8 in. (270 mm) diameter blastholes, the DM-M2 provides 75,000 lb. (34,000 kg) of bit load and a 35 ft. (10 m) drill pipe change. Advanced frame and tower design and a unique, patented carriage feed system allow on-board drill depths to 175 ft. (53 m). Compressor/engine packages in both low-pressure, [1900 CFM @ 110 PSI (51 m3/min. @ 758 kPa)] for rotary drilling and high pressure [1250 CFM @ 350 PSI (35.4 m3/min. @ 2,413 kPa)], for downhole drilling, are available.



Power PackEngine #1 Caterpillar 3412E / EPA certified


Engine #2 Cummins QSK19 / EPA certified


Engine #3 Caterpillar 3412E / EPA certified


RotationType Two-motor, variable displacement

Speed Range 0-150 rpm, variable Head Torque 0-8,640 ft-lbs (0-11,714 Nm) (forward)

Feed SystemType Patented carriage feed

Weight on Bit 0 to 75,000 lb. / 0 to 34,019 kg Tower



UndercarriageModel Caterpillar 330EL or equivalent

Carousel

Size Holds 2 to 4 drill pipe depending on pipe diameter



EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-29

Options




Medium Yes Soft Yes

Drill ApplicationMining Yes



HOME BACK

EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-30

Select Model:

T4BHDM25/SP


351

Rotary - T4BH

The T4BH is a truck-mounted, hydraulic tophead drive multipass rotary drill specificaly designed for production blasthole drilling to depths of 150 ft. (45.7 m) with a 25 ft. (7.6 m) drill pipe change. Nominal hole size is 5-1/8 to 7-7/8 in. (130 to 200 mm) for rotary or DHD drilling methods. Feed pressure generates a bit load force of up to 30,000 lb. (12,610 kg). An angle drilling option is available. All drill functions are controlled from the newly designed operator cab.



CarrierChassis (Standard) Crane Carrier, Custom, 3 axle, 6X4

Engine CAT C10 (305 HP) Power Pack


Compressor #1 IR HR2-900/350 CFM @ PSI / 25.5/2413 m3/min@kPA



Engine #3 Cummins QSK-19C (700 HP @ 2100 RPM)

Compressor #3 IR HR2.5 - 1250/350 CFM @ PSI / (35.39 @ 2413) m3/min@kPA



Speed Range 0-160 RPM (std.) Head Torque 6,500 ft-lb. / (8,814 N-m)

Option 7,165 ft-lb @ 0-130 RPM / 9,716 N-m @ 0-130 RPM

Feed SystemType Hydraulic cylinders w/cable and chain

Pulldown 0-37,700 lbs. / 17,108 kg.



EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-31

TowerPipe Length 25 ft. / 7.6 m.

Construction 4 member open front with ASTM A500 GRB steel tubing.

Cab & Controls

Operator Cab New cab designed to optimize operator comfort and safety

Controls All operational functions controlled from driller console in cab

Options

Option #1 Contact your local distributor for a complete list of options.

Weight & DimensionsHeight (Tower Up) 28-3/4 ft. / 8.7 m


Hard Yes Medium Yes



Drilling MethodRotary Yes


HOME BACK

EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-32

Select Model:

CM695DDM25/SP

DM30DM45/HPDM45/SPDM-L/HPDM-M2

DHD - DM-M2

Designed for rotary or downhole drilling of up to 10-5/8 in. (270 mm) diameter blastholes, the DM-M2 provides 75,000 lb. (34,000 kg) of bit load and a 35 ft. (10 m) drill pipe change. Advanced frame and tower design and a unique, patented carriage feed system allow on-board drill depths to 175 ft. (53 m). Compressor/engine packages in both low-pressure, [1900 CFM @ 110 PSI (51 m3/min. @ 758 kPa)] for rotary drilling and high pressure [1250 CFM @ 350 PSI (35.4 m3/min. @ 2,413 kPa)], for downhole drilling, are available.



Power PackEngine #1 Caterpillar 3412E / EPA certified


Engine #2 Cummins QSK19 / EPA certified


Engine #3 Caterpillar 3412E / EPA certified


RotationType Two-motor, variable displacement

Speed Range 0-150 rpm, variable Head Torque 0-8,640 ft-lbs (0-11,714 Nm) (forward)

Feed SystemType Patented carriage feed

Weight on Bit 0 to 75,000 lb. / 0 to 34,019 kg Tower



UndercarriageModel Caterpillar 330EL or equivalent

Carousel

Size Holds 2 to 4 drill pipe depending on pipe diameter



EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-33

Options




Medium Yes Soft Yes




HOME BACK

EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-34

Select Model:

CM695DDM25/SP


DHD - DM30

The DM30 is a hydraulic tophead drive, multi-pass, crawler-mounted drill rig designed for blastholes ranging from 5-1/8 to 6-3/4 in. (130 to 171 mm) in diameter. On-board depth capability is up to 150 ft. (45.7 m). For rotary drilling, the DM30 can assert a bit load force up to 30,000 lb. (13,608 kg) and rotation speeds of 0-130 RPM. This rig can also be used with downhole drills when equipped with a high-pressure air compressor option.













Head Torque 5,400 ft-lb. / 7,322 N-m Speed 0-100 rpm

Feed SystemType Single cylinder, cable feed

Bit Load 30,000 lb / (13,608) kg Tower





EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-35

UndercarriageManufacturer Caterpillar

Options




Hard Yes Medium Yes





HOME BACK

EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-36

Select Model:

CM695DDM25/SP


DHD - DM25/SP

The DM25SP is a crawler-mounted rotary table drill rig designed for single-pass blasthole drilling to depths of up to 50 ft. (15.2 m) and diameters of 3-1/2 to 6-3/4 in. (89 to 171 mm). This drill is capable of rotary drilling with 25,000 lb. (11,340 kg) of bit load at 0-200 rpm. The DM25SP can also be used with downhole drills when equipped with a high-pressure air compressor option.











RotationType Rotary Table Drive

Speed 0-170 rpm Torque 3,500 / (4,746 N-m)

Feed SystemType Heavy-duty chains through cluster sprocket


Construction 4 main member, open front, rectangular steel tubing

#1 Single pass depth 40 ft. / 12.2 m. #2 Single pass depth 50 ft. / 15.2 m.

Undercarriage



EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-37

Type Excavator Options


Weight & Dimensions

Weight Varies according to drill pipe: 60,000 - 62,000 lb / 27,216-28,123 kg


Medium Yes Soft Yes

Drill ApplicationQuarry Yes



HOME BACK

EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-38

Select Model:

CM695DDM25/SP


DHD - DM45/SP

The DM45/SP is a crawler-mounted hydraulic rotary table drive, drill rig designed to produce 50 ft. (15.2 m) of clean hole in a single pass. Hole diameter capability is 5-1/2 to 6-3/4 in. (139.7 to 171.5 mm) to a depth of up to 50 ft. (15.2 m) with a downhole hammer (high-pressure air package). Feed pressure generates a bit load force of up to 25,000 lb. (11,340 kg). An optional angle drilling system is available.











RotationType Rotary table w/kelly drive

Speed 0-200 rpm Torque 4,000 ft-lb / (5,424 N-m)

Feed SystemType Chain and cable


Type Single Pass Pipe Length 50 ft. / 15.2 m.

4 member open front with rectangular steel



EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-39

Construction tubing Undercarriage

Type Excavator-type Options


Weight & DimensionsHeight (Tower Up) 76-1/2 ft. / 23.3 m


Hard Yes Medium Yes

Drill ApplicationMining Yes Quarry Yes

Drilling MethodDHD Yes


HOME BACK

EP OctpbEP 1110-1-8, Vol. 430 Nov 11

L-40

Select Model:

LM100ACM348

ECM350

Pneumatic Crawler - ECM350

This agile, powerfull drill climbs steep grades over roughest ground, and takes the punishment. You have seen thousands of them on construction jobs of all kinds around the world. The basic ECM350 design has seen many improvements in its years of service ? but every drill produced has set the world standard for reliability and perfomance in its time. The ECM350 is also a fine quarry drill when teamed with an Ingersoll-Rand air compressor. This high-performance team gets more work done faster, more efficiently, and keeps doing it longer than anything else in its class.


Nominal Hole DiameterDiameter 2-1/2 - 5-1/2 in.

DrifterDrifter #1 VL140

Hole Diameter #1 2.5-4 " / 64-102 mm Rotation Speed #1 0 - 72 rpm

Frequency #1 2100 BPM

Air Consumption #1 750 SCFM @ 100 PSI / 21.2 m3/min @ 7 kg/cm2

Stroke #1 5-1/2 in. / 140 mm. Bore #1 5-1/2 in. / 140 mm.

Weight #1 421 lb. / 191 kg. Guide

Guide Dump #1 180 °Guide Swing (L/R) 50 deg / 35 deg

BoomBoom Swing (L/R) #1 40 ° / 35 °

Boom Lift (Up/Down) #1 45 ° / 15 ° Air Rotary Head

Weight 554 lb. / 252 kg.

Torque Max. 1492 Nm @ 8.4 kg/cm? / (1100 lb-ft @ 120 PSI)

Rotation 0 - 72

Air Consumption 120 CFM @ 50 RPM & 90 PSI / 3.4 m3/min @ 50 RPM & 6.3 kg/cm2

Gear Ratio 33:1

Horse Power 2.23 kw @ 6.3 kg/cm? (3.0 hp @ 90 psig) / 3.13 kw @ 8.4 kg/cm? (4.2 hp @ 120 psig)

GeneralFeed/Pullback Force 3,000 lb / 1,361 kg



EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-41

Downhole DrillsO.D. #1 3.62 in. / 92 mm.

Length (bit ext.) #1 45.7 in. / 1161 mm. Air Consumption @ 10.5 kg/cm? (150

PSIG) #1 5.1 m?/min / (180 SCFM)

Air Consumption @ 17.6 kg/cm? (250 PSIG) #1 9.9 m?/min / (350 SCFM)

Drill #2 DHD350R Hole Diameter #2 5-1/8 - 5-1/2 in. / 130-140 mm.

Weight (less bit) #2 151 lb. / 68.5 kg. O.D. #2 4.5 in. / 114 mm.

Length (bit ext.) #2 54.6 in. / 1388 mm. Air Consumption @ 10.5 kg/cm? (150

PSIG) #2 7.9 m?/min / (280 SCFM)

Air Consumption @ 17.6 kg/cm? (250 PSIG) #2 14.7 m?/min / (520 SCFM)

Crawlair Drill SpecificationsNet weight 12,900 lb. / 5851 kg.

Overall shipping length 12 ft. 0 in. / 3645 mm. Width 8 ft 0 in. / 2438 mm.

Height (vertical guide) 18 ft. 10 in. / 5753 mm. Steel change 12 ft. / 3645 mm.

Drill travel 14 ft. 3 in. / 4356 mm. Max. horizontal boom swing 40? left, 35? right

Max. vertical boom movement 45? above, 15? below Max. guide swing 50? left, 35? right Max guide dump 180?

Ground clearance 12 in. / 292 mm. Grouser width 10 in. / 254 mm.

Weight & DimensionsGround Clearance 12 " / 292 mm

Shipping Width 96 " / 2438 mm Shipping Length 144 " / 3645 mm

Approx. Working Weight 12,900 lbs. / 5851 kg. Material To Be Drilled

Hard Yes Medium Yes


Mining Yes Construction Yes

Quarry Yes Drilling Method

Drifter Yes


HOME BACK


L-42

Select Model:

ECM470ECM580ECM590

ECM660IIECM-720

Hydraulic Crawler - ECM-720

They said it couldn't be done...they were wrong. The new ECM-720 crawler drill delivers a perfect balance of productivity and cost efficiency. Hole straightness, faster penetration rates, long accessory life, and increased profitability are just a few of the results you can expect with the ECM-720.



DrifterType Montabert HC-200A

Boom & GuideBoom Swing 45 deg right / 20 deg left maximum

Vertical Boom Movement 50 deg up / 20 deg down maximum Guide Swing 20 deg right / 90 deg left maximum Guide Dump 135 deg maximum

Boom Extension 36 in. / 914 mm Guide Extension 5 ft / 1,524 mm

Overall Guide Length 27 ft 6 in / 8.4 m Drifter Travel 16 ft. 11 in. / 5.15 m

EngineType CAT 3176 C-10

Rated Power 365 HP / 272 kW Operating Speed 1,800 rpm

CompressorType Ingersoll-Rand Rotary Screw

Volume 480 CFM / 13.6 m3/min Pressure 150 PSI / 10.3 BAR

Cab & ControlsOperator Cab ROPS/FOPS

Noise level 80 dBA General

Gradeability 35 deg (70 percent) °Tramming Speed 2.0 mph / 3.3 km/hr Ground clearance 17 in. / 432 mm.

Grouser Width 13-3/4 in. / 349 mm mm. Rod Changer Capacity (6) 12 ft (3.66 m) / (6) 14 ft (4.27 m) opt.

Shipping InformationWeight 45,900 lb / 20,820 kg



EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-43

Width 8 ft 3 in / 2.5 m Length 35 ft 8 in / 10.9 m Height 10 ft 8 in / 3.3 m


Medium Yes Soft Yes


Construction Yes Quarry Yes

Drilling MethodDrifter Yes


HOME BACK


L-44

Select Model:

ECM470ECM580ECM590

ECM660IIECM-720

Hydraulic Crawler - ECM590

The ECM-590 is a self-contained, cabless hydraulic crawler drill capable of drilling up to 4 in. (102 mm) holes. It is available in either a YH70 drifter and rod rack configuration for smaller hole work, or with a YH80 and rod changer for higher production requirements. An extended guide option for 20 ft. (6.1 m) starter steel is available.



DrifterDrifter #1 YH70

Hole Diameter #1 2.5-4 " / 64-102 mm Rotation Speed #1 0-200 rpm

Frequency #1 2800 BPM Weight #1 419 lb. / 190 kg.

Steel Size #1 T45/T38 Drifter #2 YH80A

Hole Diameter #2 2.5-4.5 in. / 64-114 mm. Rotation Speed #2 0-200 rpm

Frequency #2 2600 BPM Weight #2 462 lb. / 210 kg.

Steel Size #2 T51/T45 Hydraulic Pressure 2130 psi / 150 kg/cm?

Boom & GuideHorizontal Boom Swing 30 deg R / 34.6 deg L

Vertical Boom Movement 51 deg up / 15 deg down Guide Swing 48 deg R / 40 deg L Guide Dump 180 deg

Boom Extension - YH70 (YH80A) 48 in (30 in) / 1,219 mm (762 mm) Drifter Travel - YH70 (YH80A) 15 ft 4 in (14 ft) / 3,099 mm (4,267 mm)

Guide Extension 4 ft / 1,219 mm Overall Guide Length 23 ft 8 in / 7,214 mm

EngineType Cummins 6CT8.3

Rated Power 215 HP / 159 kW Operating Speed 2350 rpm



EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-45

IR Rotary Screw CompressorCompressor pressure(max) 140 psig / 9.8 kg/cm2

Compressor volume 250 cfm / 7 m?/min General

Gradeability 35 °Tramming Speed 2 mph / 3.3 km/hr

Grouser Width 12 in. / 305 mm. Steel length starter rod 14 ft. / 4.27 m.

Weight & DimensionsLength 232.9 " / 5918 mm

Weight #2 24,500 lb. / 11,150 kg. Ground Clearance 18 " / 457 mm

Shipping Width 95.98 " / 2438 mm Shipping Height 112 " / 2845 mm


Medium Yes Soft Yes

Drill ApplicationConstruction Yes

Drilling MethodDrifter Yes


HOME BACK


L-46

Select Model:

LM100ACM348

ECM350

Pneumatic Crawler - LM100A

The LM100A is a small class pneumatic Crawlair?, capable of drilling 1-3/4" to 4- 1/2" (44 - 114 mm) diameter holes. It can be equipped with either of two drifters or a BRH rotary head for downhole drilling. The LM100A is ideal for applications in confined areas where hand-held tools are not enough, and is light enough to transport by helicopter. Like all Ingersoll-Rand crawler drills, the LM100A is "Abuse Resistant". It keeps coming back for more!



CarrierOverall Track Length 72 " / 1845 mm

Ground Clearance 9 " / 230 mm Oscillation 20 °Air Motors 4.5 HP

Gradeability 30 °Tramming Speed 0-2 mph / 0-3.2 km/hr

DrifterType Ingersoll-Rand YD90

Hole Diameter #1 1.75-2.5 " / 44-64 mm Frequency #1 1600 BPM

Air Consumption #1 375 scfm @ 100 psi & 50 rpm / 10.6 m3/min @ 7 kg/cm2 & 50 rpm

Stroke #1 3.4 in. / 85 mm. Bore #1 3.5 in. / 90 mm.

Steel Size #1 10 ft / 3048 mm Drifter #2 VL120

Hole Diameter #2 2 - 3.5 in. / 51 - 89 mm. Frequency #2 1900 BPM

Air Consumption #2 600 SCFM @ 50 RPM & 100 psi / 17.0 m3/min @ 50 RPM & 7 kg/cm2

Stroke #2 3.62 in. / 92 mm. Bore #2 4.75 in. / 120 mm.

Steel Size #2 10 ft / 3048 mm Guide

Guide Dump #1 75 °Guide Swing (L/R) 45 deg/45 deg



EP Octpb

EP 1110-1-8, Vol. 430 Nov 11

L-47

Guide Extension #1 29 " / 750 mm Drill Rod Length 10 ft. / 3 m Feed Motor Pull 3000 lbs. / 1360 kg.

BoomBoom Swing (L/R) #1 30/35 °

Boom Lift (Up/Down) #1 45/30 ° Coverage Length 107 " / 2720 mm

Max. Drill Height (Horizontal) 99 " / 2510 mm BRH Rotary Head

Weight 304 lbs. / 138 kg. Torque Maximum 700 lb.-ft. / 96.7 kg.-m Rotation Range 0 - 50 RPM

Air Consumption 120 SCFM @ 50 RPM & 100 psi / 3.39 m3/min @ 50 RPM & 7 kg/cm2

Gear Ratio 20:1 Horse Power @ 100 psi (7 kg/cm) 4.5 HP / 3.35 kW

Weight & DimensionsWidth 75 " / 1905 mm

Length (Boom @45°) 195 " / 4950 mm Minimum Height 44 " / 1120 mm

Height (Boom @45°) 188 " / 4775 mm Hole Size 1.75-4.5 " / 44-114 mm

Weight Less Drifter 5400 lbs. / 2450 kg. Material To Be Drilled

Hard Yes Medium Yes


Mining Yes Construction Yes

Quarry Yes Drilling Method

Drifter Yes


HOME BACK


L-48

GLOSSARY

Terms and Abbreviations

EP 1110-1-8, Vol. 430 Nov 11

Glossary-1

AVF average value factor bhp brake horsepower CAT category CENWW U.S. Army Corps of Engineers, Walla Walla District CMR cost of money rate cwt hundredweight D diesel DC discount code DEPR depreciation DT drive tire E electricity EAF economic adjustment factor EK economic key EP Engineer Pamphlet ER Engineer Regulation FAR Federal Acquisition Regulation EFAR Engineer Federal Acquisition Regulation FCCM facilities capital cost of money FOG filters, oil, and grease FT front tire G gas G&A general and administrative gal gallon GCW gross combined weight GVW gross vehicle weight hp horsepower HPF horsepower factor hr hour ID No. identification number IGE Independent Government Estimate kW kilowatt LAF labor adjustment factor lbs pounds LIFE Chapter 1 economic life (probably should take this out) N number of years PDF portable document format PTO power take off RCF repair cost factor RF repair factor ROPS Rollover protective structures RPR repairs SLV salvage value

EP 1110-1-8, Vol. 430 Nov 11

Glossary-2

SUB subcategory TCI tire cost index TEV total equipment value TT trailing tire WHPY working hours per year wk week WLS water, lube, and supplies yr year

EP 1110-1-8, Vol. 430 Nov 11

Glossary-3


EP 1110-1-8, Vol. 430 Nov 11

Glossary-4

EQUIPMENT INDEX CAT DESCRIPTION PAGE

A10 AGGREGATE / CHIP SPREADERS ................................................................... 2-20

A15 AIR COMPRESSORS, PORTABLE .................................................................... 2-21

A20 AIR HOSE, TOOLS & EQUIPMENT ................................................................... 2-25

A25 ASPHALT PAVING DISTRIBUTORS ................................................................. 2-28

A30 ASPHALT PAVERS & MISCELLANEOUS ROAD EQUIPMENT ........................ 2-29

A35 ASPHALT PAVING KETTLES ............................................................................ 2-34

A40 ASPHALT & CONCRETE MILLERS / PROFILERS / PLANERS / ROTARY

GRINDERS ................................................................................................................ 2-34

A45 ASPHALT RECYCLERS & SEALERS ................................................................ 2-35

B10 BATCH PLANTS, ASPHALT & CONCRETE ...................................................... 2-37

B15 BROOMS, STREET SWEEPERS & FLUSHERS ............................................... 2-44

B20 BRUSH CHIPPERS ............................................................................................ 2-46

B25 BUCKETS, CLAMSHELL .................................................................................... 2-47

B30 BUCKETS, CONCRETE ..................................................................................... 2-49

B35 BUCKETS, DRAGLINE ....................................................................................... 2-52

C05 CHAIN SAWS ..................................................................................................... 2-59

C10 COMPACTORS, WALK-BEHIND OR REMOTE CONTROLLER ....................... 2-59

C15 CONCRETE CLEANERS / ABRASIVE BLASTERS ........................................... 2-62

C20 CONCRETE BUGGIES ...................................................................................... 2-63

C25 CONCRETE FINISHERS/SCREEDS/SPREADERS .......................................... 2-63

C35 CONCRETE GUNITERS / SHOTCRETERS ...................................................... 2-66

C40 CONCRETE MIXING UNITS .............................................................................. 2-68

C45 CONCRETE PAVING MACHINES ..................................................................... 2-70

C55 CONCRETE PUMPS .......................................................................................... 2-72

C60 CONCRETE SAWS (Add cost for sawblade wear) ........................................... 2-74

C65 CONCRETE VIBRATORS .................................................................................. 2-76

C75 CRANES, HYDRAULIC, SELF-PROPELLED .................................................... 2-77

EP 1110-1-8, Vol. 430 Nov 11

Index-1

C80 CRANES, HYDRAULIC, TRUCK MOUNTED ..................................................... 2-80

C85 CRANES, MECHANICAL, LATTICE BOOM, CRAWLER MOUNTED ................ 2-82

C90 CRANES, MECHANICAL, LATTICE BOOM, TRUCK MOUNTED .................... 2-87

C95 CRANES, TOWER ............................................................................................. 2-87

D10 DRILLS, HYDRAULIC TRACK (Add cost for drill steel and bit wear) ................. 2-91

D15 DRILLS, HORIZONTAL ...................................................................................... 2-92

D20 DRILLS, CORE, COLUMN MOUNTED (Add cost for drill steel and bit wear) .... 2-95

D25 DRILLS, CORE & DOWELLING (Add cost for drill steel and bit wear) ............... 2-96

D30 DRILLS, EARTH / AUGER (Add cost for drill steel and cutting edge wear) ........ 2-97

D35 DRILLS, ROTARY BLASTHOLE (Add cost for drill steel and bit wear) .............. 2-98

F10 FORK LIFTS ..................................................................................................... 2-100

G10 GENERATOR SETS ........................................................................................ 2-101

G15 GRADERS, MOTOR ........................................................................................ 2-103

H10 HAMMERS, HYDRAULIC (Demolition tool) (Add cost for point wear) .............. 2-105

H13 HAZARDOUS/TOXIC WASTE EQUIPMENT ................................................... 2-107

H20 HOISTS & AIR WINCHES ................................................................................ 2-121

H25 HYDRAULIC EXCAVATORS, CRAWLER MOUNTED ..................................... 2-122

H30 HYDRAULIC EXCAVATORS, WHEEL MOUNTED .......................................... 2-136

H35 HYDRAULIC SHOVELS, CRAWLER MOUNTED ............................................ 2-137

L10 LAND CLEARING EQUIPMENT ....................................................................... 2-138

L15 LANDSCAPING EQUIPMENT .......................................................................... 2-140

L20 LIGHTING SETS, TRAILER MOUNTED ........................................................... 2-143

L25 LINE STRIPING EQUIPMENT .......................................................................... 2-144

L30 LOADERS, BELT (Conveyor belts) & ACCESSORIES ..................................... 2-145

L35 LOADERS, FRONT END, CRAWLER TYPE .................................................... 2-146

L40 LOADERS, FRONT END, WHEEL TYPE ........................................................ 2-147

L50 LOADERS / BACKHOE, WHEEL TYPE ............................................................ 2-151

L55 LOADER / BACKHOE, ATTACHMENTS ......................................................... 2-152

L60 LOG SKIDDERS ............................................................................................... 2-153

M10 MARINE EQUIPMENT (NON DREDGING) .................................................... 2-154

P10 PILE HAMMER ACCESSORIES - EXTRACTORS & BOX LEADS .................. 2-159

EP 1110-1-8, Vol. 430 Nov 11

Index-2

P20 PILE HAMMERS, DOUBLE ACTING ................................................................ 2-160

P25 PILE HAMMERS, SINGLE ACTING ................................................................ 2-161

P30 PILE HAMMERS, DRIVER/ EXTRACTOR, VIBRATORY ................................. 2-164

P35 PIPELAYERS.................................................................................................... 2-165

P40 PLATFORMS & MAN-LIFTS ............................................................................. 2-165

P45 PUMPS, GROUT .............................................................................................. 2-167

P50 PUMPS, WATER, CENTRIFUGAL, TRASH ..................................................... 2-169

P55 PUMPS, WATER, SUBMERSIBLE ................................................................... 2-171

P60 PUMPS, WATER, CENTRIFUGAL, DEWATERING ......................................... 2-173

P65 PUMPS, WATER, DIAPHRAGM ....................................................................... 2-174

P70 PUMPS, WATER (For core drills) ..................................................................... 2-176

R10 RIPPERS & HYDRAULIC BANK SLOPERS (Add cost for point wear) ............ 2-176

R15 ROLLERS, STATIC, TOWED, PNEUMATIC .................................................... 2-178

R20 ROLLERS, STATIC, TOWED, STEEL DRUM .................................................. 2-179

R30 ROLLERS, STATIC, SELF-PROPELLED ......................................................... 2-179

R40 ROLLERS, VIBRATORY, TOWED ................................................................... 2-183

R45 ROLLERS, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM .................... 2-183

R50 ROLLERS, VIBRATORY, SELF-PROPELLED, SINGLE DRUM ...................... 2-185

R55 ROOFING EQUIPMENT ................................................................................... 2-189

S10 SCRAPERS, ELEVATING ................................................................................ 2-191

S15 SCRAPERS, CONVENTIONAL ........................................................................ 2-191

S20 SCRAPERS, TANDEM POWERED .................................................................. 2-192

S25 SCRAPERS, TRACTOR DRAWN .................................................................... 2-193

S30 SCREENING & CRUSHING PLANTS .............................................................. 2-194

S35 SNOW REMOVAL EQUIPMENT ...................................................................... 2-208

S40 SOIL & ROAD STABILIZERS ........................................................................... 2-209

S45 SPLITTERS, ROCK & CONCRETE .................................................................. 2-210

T10 TRACTOR BLADES & ATTACHMENTS (including agricultural)....................... 2-210

T15 TRACTORS, CRAWLER (DOZER) (includes blade) ........................................ 2-213

T20 TRACTORS, WHEEL TYPE (DOZER) ............................................................. 2-217

T25 TRACTORS, AGRICULTURAL ......................................................................... 2-217

EP 1110-1-8, Vol. 430 Nov 11

Index-3

T30 TRENCHERS, CHAIN TYPE CUTTER ............................................................. 2-219

T35 TRENCHERS, WHEEL TYPE CUTTER ........................................................... 2-221

T40 TRUCK OPTIONS ............................................................................................. 2-222

T45 TRUCK TRAILERS ........................................................................................... 2-227

T50 TRUCKS, HIGHWAY (Add attachments as required) ....................................... 2-232

T55 TRUCKS, OFF-HIGHWAY ................................................................................ 2-236

T56 TRUCKS, OFF-HIGHWAY/PRIME MOVER TRACTORS & WAGONS ............ 2-239

T57 TRUCKS, VACUUM .......................................................................................... 2-239

T60 TRUCKS, WATER, OFF-HIGHWAY ................................................................. 2-240

T65 TUNNEL/MINING EQUIPMENT ........................................................................ 2-241

W25 WATER & CO2 BLASTERS............................................................................. 2-241

W30 WATER TANKS ............................................................................................... 2-246

W35 WELDERS ....................................................................................................... 2-247

EP 1110-1-8, Vol. 430 Nov 11

Index-4

EP 1110-1-8 (Vol. 4), Construction Equipment …...DEPARTMENT OF THE ARMY EP 1110-1-8 U.S. Army...

Documents

Transcript of EP 1110-1-8 (Vol. 4), Construction Equipment …...DEPARTMENT OF THE ARMY EP 1110-1-8 U.S. Army...