Envelope cutting presses

www.freemanschwabe.comFreeman Schwabe Machinery: 4064 Clough Woods Drive, Cincinnati, Ohio 45103 USAEmail: [email protected] Tel: +1 513 947 2888 !1

Freeman Schwabe MachineryEnvelope Cutting Machines


Envelope Cutting Machines

Model EA25

Automatic Envelope Cutting Machine


Cutting Force – Twenty-Seven (27) U.S. Tons

Head Size - 24.4”D x 24.4”W

Maximum Blank Size - 23.6”D x 23.6”W

Maximum Material Size - 37.4”D x 57.1”W

Cutting Stroke - 7.1”, adjustable. Includes four (4) post-manually adjustable synchronized mechanical stop rods for restriction of bottom of stroke for increased die and cutting pad life. Complete with ratchet and dial indication for adjustment.

Daylight Opening – Approximately 8.9”, without cutting pad

Die Mounting - Magnetic fixture provided in head of press with keyway (and fixed keys) for precise die positioning. Magnetic fixture also enables dies without backing plates to be used. Also includes a foot pedal for energizing the magnet for the die clamping.

Cutting Surface –Polypropylene cutting pad with automatic pad oscillator located on the sliding table

Model EA25Automatic Envelope Cutting Machine



Feed System

Automatic power operated sliding table with pneumatically actuated “lift” holding clamps, mounted on rear of sliding table, set up to operate automatically in conjunction with cutting cycle.

The clamps are individually controlled and can be programmed to retract in order to achieve full material utilization.

Air flotation in lower clamps allows minor adjustment of the paper stack.


• Internal production counter is accessed through press computer (“PC”).

• Includes the movable dry run controller, which is used to edit a program for a printed sheet – BIG time saver!

• Material side guides with retractable pneumatic pusher in order to square up “lifts”.

• Pneumatic cut sheet pusher automatically power shifts “lift” with envelopes and waste to side table for easy cut parts picking.

• Die lubricating roller moves across edge of die for improved cut quality and prolonged die life.

• Die lubricating pad for improved cut quality and prolonged die life.

• Pneumatic knock-out unit assists in separating cut envelopes from waste.

• Head mounted pressure plate insures consistent cutting through entire lift of paper and also assist in ejecting envelopes from cutting die. Includes a switch on the main control panel to turn the ejector ‘on’ & ‘off’.

• Pressure roller insures flatness of “lift”(programmable).

• Air cylinders are ISO standard for easy maintenance.


www.freemanschwabe.comOctober 22, 2013Freeman Schwabe Machinery: 4064 Clough Woods Drive, Cincinnati, Ohio 45103 USA Email: [email protected] Tel: +1 513 947 2888!6


Model EM30

Manual Envelope Cutting Machine


Cutting Pressure – 27 U.S. Tons or 33 U.S. Tons

Head Size –23.6”D x 23.6”W

Cutting Stroke – 5.1”

Cutting Surface - Polypropylene cutting pad with automatic pad shifter located on the sliding table for added die and pad life.

Guarding – Front Type 4 light safety curtain and rear safety guarding. Also includes head safety blocks for working under the head of the press.

!Frequency converter cushion system for soft stopping ability.

Die lubricating roller for improved cut quality and prolonged die life.

Adjustable material side guides.

Manual Die Rails

!


Model EM30 & EM25

Semi-Automatic Envelope Cutting MachineIdeal for 4 Corner Dies


Envelope Cutting Machines Model RH30

Receding Head Press for Cutting Envelopes


Receding Head – Rack and pinion drive with acceleration/deceleration ramping for smooth starting and stopping. A cross-center push bar is included in the head of the press.

Cutting Surface - Oscillating pad unit, mounted on bed of press for increased cutting pad life. Includes power driven device to move the cutting pad as required.

Scrap Removal Conveyor - Front scrap conveyor to remove scrap manually pushed to the front of the press. 8” Wide x 6” Deep. Includes bonded “Vee” type belt. This will be bonded to the flat belt for improved guiding of material scrap. Side shields are provided to prevent scrap from getting directly between the belt and the conveyor sidepieces.




Rear Removal Tray – The press includes a rear removal tray, which enables the operator to push the scrap off the back of the press and slide into a large collection bin. This tray is for use with a collection bin which is 31.5”high x 40”wide x 40”deep. The gap between the cutting surface and the top of the collection bin is approximately 3”. Enough clearance will be provided between the flywheel housing and the inside of the rear guard support legs for wheeled collection bin to roll in from the side of the machine.

Laser Light Projector – 2-laser projector for material loading position, which includes an on/off switch.

Oil Pan System to lubricate dies – Pneumatically operated pan on rear of press replaces existing oil roller system.





Model FH 40

Full Head Press for Cutting EnvelopesWith Single or Dual Motorized Table Feed System



Model FH 40


Model FH - 40 Cutting Force – 44 US Tons Cutting Stroke – 9.8” Daylight – 11.8” does not include cutting

surface Main Motor – 5 Hp Machine Bed – 47.2” deep x 63” wide Effective Cutting Area – 45.3” deep x 61”

with no die rails or pad shifter Other sizes available


• Uses Head Mounted Dies with T-slots • Single Power Table w/ Cutting Pad • 1 Hp frequency converter drives a ball

screw for the power table - +/- 0.004” • OSHA/CE Compliant • Allen Bradley/Siemens PLC • Linear Transducer for Stroke Control • Minimal Maintenance


Model FH 40


Envelope cutting presses

Documents

Transcript of Envelope cutting presses