Engineering Drawing : Class 02
-
Upload
suhaimi-said -
Category
Education
-
view
611 -
download
7
Transcript of Engineering Drawing : Class 02
DJJ1012ENGINEERING DRAWING
Class 02
Suhaimi Said (PKS)
DRAWING PAPER Size..
Suhaimi Said (PKS)
Drawing Paper
• ANSI standard measure for drawing paper was as follows:
• A. 8.5” x 11”
• B. 11” x 17”
• C. 17” x 22”
• D. 22” x 34”
• E. 34” x 44”
Suhaimi Said (PKS)
TITLE BLOCKSpecial columns that prepared at every drawing
paper to give explaination on about drawing that drawn in the drawing paper.
Suhaimi Said (PKS)
Title Block
Suhaimi Said (PKS)
SCALEScale help us belittle something large objects or enlarge something small object fit with drawing
paper when draw.
Suhaimi Said (PKS)
Scale
• Following is scale rate according to BS standard ( British Standard):Full Size (1:1)
Size Reduce 1 : 2 1 : 20 1 : 200
1 : 5 1 : 50 1 : 500
1 : 10 1 : 100 1 : 1000
Size Enlarge 2 : 1 20 : 1 200 : 1
5 : 1 50 : 1 500 : 1
10 : 1 100 : 1 1000 : 1
Suhaimi Said (PKS)
Scale
1:2Refer to Drawing Size
Refer to Actual Size
Suhaimi Said (PKS)
Scale
Suhaimi Said (PKS)
ALPHABET & NUMBERThere is two methodologies that used in making letter and number.
• vertical method• sloping method
Suhaimi Said (PKS)
Vertical Method
Suhaimi Said (PKS)
STEP
Draw horizontal construction line using pencil (H)
Suhaimi Said (PKS)
STEP
Draw second horizontal line with distance 30mm with first line.
30mm
Suhaimi Said (PKS)
STEP
Draw vertical construction line.
Suhaimi Said (PKS)
STEP
Draw second vertical construction line with distance 20mm from first line.
20mm
Suhaimi Said (PKS)
STEP
Start draw your first line Alphabet HB
Suhaimi Said (PKS)
STEP
Suhaimi Said (PKS)
STEP
Suhaimi Said (PKS)
STEP
Draw vertical construction line with distance 5mm using Pencil (H)
5mm
Suhaimi Said (PKS)
STEP
Draw vertical construction line with distance 20mm using Pencil (H)
20mm
Suhaimi Said (PKS)
PRACTICAL TASK 1
Draw Alphabet from A-Z and Number 0-9 vertical method
Suhaimi Said (PKS)
Sloping Method
Suhaimi Said (PKS)
STEP
Draw horizontal construction line using pencil (H)
Suhaimi Said (PKS)
STEP
Draw second horizontal line with distance 30mm with first line.
30mm
Suhaimi Said (PKS)
STEP
Draw an angle construction line using set square 60°.
60°
Suhaimi Said (PKS)
STEP
Draw second angle construction line with distance 20mm from first line.
20mm
Suhaimi Said (PKS)
STEP
Start draw your first line Alphabet HB
Suhaimi Said (PKS)
STEP
Suhaimi Said (PKS)
STEP
Suhaimi Said (PKS)
STEP
5mm
Draw vertical construction line with distance 5mm using Pencil (H)
Suhaimi Said (PKS)
STEP
Draw vertical construction line with distance 20mm using Pencil (H)
20mm
Suhaimi Said (PKS)
PRACTICAL TASK 1
Draw Alphabet from A-Z and Number 0-9 vertical method
Suhaimi Said (PKS)
DISTANCETo avoid occurrence of word mixture that
complicate reader to read.
Suhaimi Said (PKS)
Distance
Suhaimi Said (PKS)
Types Of Lineshttp://www.wisc-online.com/Objects/ViewObject.aspx?ID=eng16004
Suhaimi Said (PKS)
Types of Lines
• OBJECT LINE
• CENTER LINE
• CENTER MARK
• HIDDEN LINE
• PHANTOM LINE
• BREAK LINE
• CUTTING PLANE LINE
• VIEWING PLANE LINE
• SECTION LINE
Suhaimi Said (PKS)
OBJECT LINE
• Object or visible lines are used to represent the outline contour of the object being drawn.
• These line appear as thick, continues line.
Suhaimi Said (PKS)
OBJECT LINE
Suhaimi Said (PKS)
CENTER LINE
• Center lines are use to represent the center of round cylindrical features, or symmetry of a feature.
• These lines appear as thin width lines with alternating long and short dashes.
Suhaimi Said (PKS)
CENTER LINE
Suhaimi Said (PKS)
CENTER MARK
• Center mark are use to represent the centerpoints of a radius (arc) or circle.
• These marks appear as small crosses at the center point of a radius or circle.
Suhaimi Said (PKS)
CENTER MARK
Suhaimi Said (PKS)
HIDDEN LINE
• Hidden lines represent edges and outlines that are invisible features of an object in a particular view .
• These lines appear as thin-width lines with short dashes.
Suhaimi Said (PKS)
HIDDEN LINE
Suhaimi Said (PKS)
PHANTOM LINE
• Phantom lines represent the outline of an adjacent part, show alternate positions of a moving part, or replace repetitive details such as gear teeth and threads.
• These lines appear as thin-width lines with two short dashes between single long dashes.
Suhaimi Said (PKS)
PHANTOM LINE
Suhaimi Said (PKS)
BREAK LINE
• Break lines represent an area of an object that has been removed for clarity or convenience
• Short break lines appear as short lines within the object, and long break lines appear as longer lines that represent a larger portion of an object that was removed to shorten the view.
Suhaimi Said (PKS)
BREAK LINE
Suhaimi Said (PKS)
CUTTING PLANE LINE
• Cutting Plane Line represent an imaginary cut through a part to show a cross section.
• These lines may be a series of long dashes or two short dashes between a pair of long dashes.
Suhaimi Said (PKS)
CUTTING PLANE LINE
Suhaimi Said (PKS)
VIEWING PLANE LINE
• Viewing Plane Line represent the direction of sight used to view a particular feature.
• These lines may be a series of long dashes or two short dashes between a pair of long dashes.
Suhaimi Said (PKS)
VIEWING PLANE LINE
Suhaimi Said (PKS)
SECTION LINE
• Viewing Plane Line are used to show where material has been cut away in a section view. A cutting plane line or break lines may be use to exposed the material.
• These lines are drawn using different patterns to designate various type of materials.
Suhaimi Said (PKS)
SECTION LINE
Suhaimi Said (PKS)