Enetwork Practice SBA

7/27/2019 Enetwork Practice SBA

1/12

Sunt 2 variante, trebuie modificat linkul dintre PC si router

(cablu drept) si IP-ul de pe PC.

1- ENetwork Basic Configuration PT Practice SBA 2012

A few things to keep in mind while completing this activity:

1. Do not use the browserBack button or close or reload any exam windows during the exam.

2. Do not close Packet Tracer when you are done. It will close automatically.

3. Click the Submit Assessment button to submit your work.

Introduction

In this practice Packet Tracer Skills Exam, you will:

design and implement an addressing scheme to meet stated requirements

configure, verify, and troubleshoot connectivity between all devices in the network

Addressing Table

Device Interface Address Subnet Mask Default Gateway

Router1Fa0/0 172.16.1.1 255.255.255.224 n/a

Fa0/1 172.16.1.33 255.255.255.240 n/a

Switch1 VLAN1 172.16.1.2 255.255.255.224 172.16.1.1

PC1 NIC 172.16.1.30 255.255.255.224 172.16.1.1

PC2 NICPreconfigured

(172.16.1.35)

Preconfigured

(255.255.255.240)

Preconfigured

(172.16.1.33)

NOTE: The initial network has some errors. To aid in configuring and verifying the devices, as well asin troubleshooting the existing errors, use a printed version of these instructions to fill in the missingaddress information in the table during Step 1.

Step 1: Determine the IP Addressing Scheme.

Design an addressing scheme and fill in the Addressing Table based on the following requirements:

a.Subnet the address space 172.16.1.0/24 to provide 30 host addresses for LAN 1 while wasting the leastamount of address space.

b.Assign the first available subnet to LAN 1.c.Assign the lowest (first) host address in this subnet to the Fa0/0 interface on Router1.d.Assign the second address in this subnet to the VLAN 1 interface on Switch1.e.Assign the highest (last) host IP address in this subnet to PC1.

Step 2: Configure Router1.

a.Configure Router1 with these basic parameters:Use Router1 asthe router name.Use class as the encrypted password for privileged EXEC mode.Require password-protected logins for the console line. Use cisco as the password.Require password-protected logins for the vty lines. Use cisco as the password.Configure the banner message-of-the-day as Authorized access only!


2/12

b.Configure the two Fast Ethernet interfaces.Configure the router interfaces according to your completed addressing table.Configure each interface with a description.c.Close the terminal window after completing the router configuration.

Step 3: Configure Switch1 and Verify Connectivity.

a.Remove the console connection between PC1 and Router1.b.Connect PC1 to the Switch1 console port.c.Configure Switch1 with these basic parameters:Use Switch1 for the switch name.Use class as the encrypted password for privileged EXEC mode.Require password-protected logins for the console line. Use cisco as the password.Require password-protected logins for the vty lines. Use cisco as the password.Configure the banner message-of-the-day asAuthorized access only!d.Configure interface VLAN 1.e.Configure the default gateway.f.Test that Switch1 is able to ping the default gateway.

Step 4: Configure and Verify PC1 Addressing.

a.Use the IP addressing you determined in Step 1 and configure PC1 with the correct addressing.b.Test that PC1 is able to ping the default gateway.

Step 5: Verify and Troubleshoot End-to-End Connectivity.

Verify that PC1 is able to ping PC2. If the ping fails, locate and correct any errors. For example, makesure PC2 is configured correctly with appropriate addressing for the subnet it belongs to.

Packet Tracer Image:


3/12

Step 2: Configure Router1.

Router>enableRouter#configure terminalEnter configuration commands, one per line. End with CNTL/Z.

Router(config)#hostname Router1

Router1(config)#enable secret classRouter1(config)#line console 0Router1(config-line)#password ciscoRouter1(config-line)#login

Router1(config-line)#exit

Router1(config)#line vty 0 4Router1(config-line)#password ciscoRouter1(config-line)#login

Router1(config-line)#exit

Router1(config)#banner motd #Authorized access only!#

Router1(config)#interface fastEthernet 0/0

Router1(config-if)#ip address 172.16.1.1 255.255.255.224Router1(config-if)#description LAN1


4/12

Router1(config-if)#no shutdown

Router1(config-if)#%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changedstate to up

Router1(config-if)#exit

Router1(config)#interface fastEthernet 0/1Router1(config-if)#ip address 172.16.1.33 255.255.255.240Router1(config-if)#description LAN2

Router1(config-if)#no shutdown

Router1(config-if)#

%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changedstate to up

Router1(config-if)#do show ip interface briefInterface IP-Address OK? Method Status ProtocolFastEthernet0/0 172.16.1.1 YES manual up upFastEthernet0/1 172.16.1.33 YES manual up up

Vlan1 unassigned YES unset administratively down down

Router1(config-if)#do writeBuilding configuration...[OK]Router1(config-if)#

Step 3: Configure Switch1 and Verify Connectivity.

Switch>enableSwitch#configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

Switch(config)#hostname Switch1

Switch1(config)#enable secret class

Switch1(config)#line console 0Switch1(config-line)#password ciscoSwitch1(config-line)#login

Switch1(config-line)#exit

Switch1(config)#line vty 0 4Switch1(config-line)#password cisco


5/12

Switch1(config-line)#login

Switch1(config-line)#exit

Switch1(config)#banner motd #Authorized acccess only!#

Switch1(config)#interface vlan 1Switch1(config-if)#ip address 172.16.1.2 255.255.255.224Switch1(config-if)#no shutdown

Switch1(config-if)#%LINK-5-CHANGED: Interface Vlan1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up

Switch1(config-if)#exit

Switch1(config)#ip default-gateway 172.16.1.1

Switch1(config)#^ZSwitch1#%SYS-5-CONFIG_I: Configured from console by console

Switch1#show ip interface briefInterface IP-Address OK? Method Status Protocol

FastEthernet0/1 unassigned YES manual up up.......................

Vlan1 172.16.1.2 YES manual up up

Switch1#writeBuilding configuration...[OK]

Switch1#ping 172.16.1.1

Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 172.16.1.1, timeout is 2 seconds:!!!!!Success rate is 100 percent (5/5), round-trip min/avg/max = 2/17/38 ms

Switch1#


6/12

Step 4: Configure and Verify PC1 Addressing.

===========================================

2- ENetwork Basic Configuration PT Practice SBA 2012

A few things to keep in mind while completing this activity:

1- Do not use the browserBack button or close or reload any Exam windows during the exam.

2- Do not close Packet Tracer when you are done. It will close automatically.

3-Click the Submit Assessment button to submit your work.

Introduction

In this practice Packet Tracer Skills Exam, you will:

design and implement an addressing scheme to meet stated requirements

configure, verify, and troubleshoot connectivity between all devices in the network


7/12

Addressing Table

Device Interface Address Subnet Mask Default Gateway

HQ

Fa0/0 10.10.10.1 255.255.255.192 n/a

Fa0/1 10.10.10.65 255.255.255.248 n/a

S2 VLAN1 10.10.10.2 255.255.255.192 10.10.10.1

NetAdmin NIC 10.10.10.62 255.255.255.192 10.10.10.1

H1 NICPreconfigured

(10.10.10.67)

Preconfigured

(255.255.255.248)

Preconfigured

(10.10.10.65)

NOTE: The initial network has some errors. To aid in configuring and verifying the devices as well as

troubleshooting the existing errors, use a printed version of these instructions to fill in the missing

address information in the table during Step 1.

Step 1: Determine the IP Addressing Scheme.

Design an addressing scheme and fill in the Addressing Table based on the following requirements:

a.Subnet the address space 10.10.10.0/24 to provide 40 host addresses for LAN 1 while wasting the least

amount of address space.

b.Assign the first available subnet to LAN 1.

c.Assign the lowest (first) host address in this subnet to the Fa0/0 interface on HQ.

d.Assign the second address in this subnet to the VLAN 1 interface on S2.

e.Assign the highest (last) host IP address in this subnet to NetAdmin.

Step 2: Configure HQ.

a.Configure HQ with these basic parameters:

Use HQ asthe router name.

Use class as the encrypted password for privileged EXEC mode.

Require password-protected logins for the console line. Use cisco as the password.

Require password-protected logins for the vty lines. Use cisco as the password.

Configure the banner message-of-the-day as Unauthorized access is prohibited.

b.Configure the two Fast Ethernet interfaces:

Configure the router interfaces according to your completed Addressing Table.


8/12

Configure each interface with a description.

c.Close the terminal window after completing the router configuration.

Step 3: Configure S2 and Verify Connectivity.

a.Remove the console connection between NetAdmin and HQ.

b.Connect NetAdmin to the S2 console port.

c.Configure S2 with these basic parameters:

Use S2 for the switch name.

Use class as the encrypted password for privileged EXEC mode.

Require password-protected logins for the console line. Use cisco as the password.

Require password-protected logins for the vty lines. Use cisco as the password.

Configure the banner message-of-the-day as Unauthorized access is prohibited.

d.Configure interface VLAN 1.

e.Configure the default gateway.

f.Test that S2 is able to ping the default gateway.

Step 4: Configure and Verify NetAdmin Addressing.

a.Use the IP addressing you determined in Step 1 and configure NetAdmin with the correct addressing.

b.Test that NetAdmin is able to ping the default gateway.

Step 5: Verify and Troubleshoot End-to-End Connectivity.

Verify that NetAdmin is able to ping H1. If the ping fails, locate and correct any errors. For example,

make sure H1 is configured correctly with appropriate addressing for the subnet it belongs to.

Packet Tracer image:


9/12

Step 2: Configure HQ.

Press RETURN to get started!

Router>enable

Router#configure terminal


Router(config)#hostname HQ

HQ(config)#enable secret class

HQ(config)#line console 0

HQ(config-line)#password cisco

HQ(config-line)#login

HQ(config-line)#exit

HQ(config)#line vty 0 4

HQ(config-line)#password cisco

HQ(config-line)#login

HQ(config-line)#exit


10/12

HQ(config)#banner motd #Unauthorized access is prohibited.#

HQ(config)#interface fastEthernet 0/0

HQ(config-if)#ip address 10.10.10.1 255.255.255.192HQ(config-if)#description LAN1

HQ(config-if)#no shutdown

HQ(config-if)#


%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed

state to up

HQ(config-if)#exit

HQ(config)#interface fastEthernet 0/1

HQ(config-if)#ip address 10.10.10.65 255.255.255.248

HQ(config-if)#description LAN2

HQ(config-if)#no shutdown

HQ(config-if)#


%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed

state to up

HQ(config)#

Step 3: Configure S2 and Verify Connectivity.

Switch>enable

Switch#configure terminal


Switch(config)#hostname S2

S2(config)#enable secret class


11/12

S2(config)#line console 0

S2(config-line)#password cisco

S2(config-line)#login

S2(config-line)#exit

S2(config)#line vty 0 4

S2(config-line)#password cisco

S2(config-line)#login

S2(config-line)#exit

S2(config)#banner motd #Unauthorized access is prohibited.#

S2(config)#interface vlan 1

S2(config-if)#ip address 10.10.10.2 255.255.255.192

S2(config-if)#no shutdown

S2(config-if)#

%LINK-5-CHANGED: Interface Vlan1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up

S2(config-if)#exit

S2(config)#ip default-gateway 10.10.10.1S2(config)#exit

S2#

%SYS-5-CONFIG_I: Configured from console by console

S2#ping 10.10.10.1

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 10.10.10.1, timeout is 2 seconds:


12/12

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 31/34/47 ms

S2#write

Building configuration...

[OK]

S2#

Enetwork Practice SBA

Documents

Transcript of Enetwork Practice SBA