Endless Pool Performance Current Supplemental...

Endless Pool Performance Current Supplemental Guide of 9

Endless Pools Inc. D40050-0811

Parts List

High Performance Internals Kit (supplied by EPI)Qty Description

1 Propulsion Housing2 Support Beams2 Outside Front Base Supports1 High Performance Width Kit

(1) Rear Base Kit(2) Front Base Wing Caps(1) Front Base Faceplate

2 Side Return Channel Kits4 Corner Turning Vane Assemblies1 Hardware Kit (packaged with the propulsion housing)

Tool Required (supplied by others)#2 Phillips Head ScrewdriverDrillMagic Marker or Pencil

Description

The Endless Pool Performance Current offers the fastest, smoothest swim current available in any swimmingmachine. The custom designed 24" x 21" outlet produces a flow of water that is wider, deeper and smootherthan our standard system. By mounting the propellers on either side of the propulsion housing the watertravels further before it enters the propulsion housing giving it more time to straighten, thereby producing anultra smooth current.

Additional Considerations

Holes will have to be drilled into the front panel of the pool to accept the hydraulic hoses for the swimcurrent. Drilling the holes will have to be done prior to installing the liner.

If hydrotherapy jets have been purchased, then one of the jet suction fittings should be installed under thefront base. The ideal placement for this suction fitting is 12�” up from the base of the panel and a minimumof 15�” away from the left edge of the front panel (as you are inside the pool facing the front panel). Thecenter point of this hole must be a minimum of 3�” away from a Z-Brace (panel stiffener).

If you have purchased a hydraulic treadmill, then read that Supplemental Guide prior to beginning thisinstallation.

Installation Instructions

1. Prior to starting the installation of the swim current components, the pool panels should be fullyassembled and square, the bracing (anchor bolts or tension straps) of the pool should be properlyinstalled, and the liner hanger should be secured to the top flange of the pool.



2. Two holes will have to be drilled into the front panel of the pool to accept the swim current hydraulichose and thru-wall assemblies. The holes must be 12�” up from the base of the panel. The hole that isclosest to the panel�’s right edge must be a minimum of 15�” away from that edge. The center pointsof each hole must be a minimum of 4�” away from each other. The center point of any hole must be3�” away from a Z-Brace (panel stiffener on the back side of the panel). Refer to the below diagramfor proper hole placement.

3. Once the liner is installed in the pool and is vacuumed in place, position the front base into the poolso that it is centered on the front panel.



4. Position the appropriate turning vane assemblies into each of the front corners of the pool.

5. Next, position the outside front base supports onto the corner turning vane assemblies. These supportare not side-specific and are interchangeable. Three screws will secure the outside support to thecorner turning vane.



6. Slide a support beam into place, interlocking the front base to the outside front base support. Again,these support beams are not side-specific and are interchangeable. The support beam notch will nestinto the grove on the under side of the outside support. Two screws will secure the support beam tothe base and two screws will secure the support beam to the outside support. Adjust this frontassembly so that it is centered on the front panel as necessary.

7. Attach the front base faceplate to the front base and corner turning vane assembly. Five screws willbe used to attach the faceplate to the front base (the top most holes in the faceplate will not get screwsat this time). In the corners, only install the lower screws.



8. Attach the rear end plates to the stainless steel vertical face with the provided screws, nuts, andwashers. Align the rear stainless steel vertical face with the rear base cap. Insert the 3/4�” screw thatthe base cap and then through the stainless steel vertical face. Place the provided 1-1/4�” washer onthe screw before installing the provided nut. Then attach the rear support to the base cap with theprovided screw. Attach the bond wire to the screw as shown prior to tightening the nut.

9. Attach the rear base to the rear corner turning vane assembly. Use the provided screws as shown toattach. Make sure to pull the bond wire through the right rear turning vane.

Bond Wire

Rear End Plate

Bond Wire



10. Install the vertical faces of the return channels and side supports as shown. Install the lower screwsonly. Make sure to pull the bond wire attached to the rear base up through the supports to the rightside support. Pull the bond wire attached to the front base back through the front turning vane andside supports back to the right side bench support. Connect both wires to the screw on the undersidethat side bench support.

11. Position the return channel caps into place.

Bond Wire(attached to Rear Base)

Bond Wire(attached to Propulsion Housing)

Bond wires connect to the screwon the underside of this sidesupport



12. Secure the return channel caps to the corner turning vane assemblies, return channel supports and thevertical face of the bench with the provided screws.

13. Begin to fill the pool with water. When the water level is just below the two thru-wall holes, its time toinstall the submersible hose assemblies. Cut the liner using the hole as a template. The thru wallfitting has 2 rubber gaskets and 1 cork gasket. One rubber gasket goes between the fitting and theliner on the inside of the pool. The other rubber gasket goes between the liner and the panel on theinside of the pool. The cork gasket goes between the panel and the lock nut on the outside of thepool. Tighten the lock nut hand-tight only. The hose that has red tape wrapped around the fitting isthe low-pressure hose. That sub-hose assembly should be installed through the hole closest to thecorner.



14. After the sub-hose assemblies have been installed continue to fill the pool. When the water level ishas reached the top of the benches, install the rear corner cover and the front wing caps. Use theprovided screws to attach.



15. Remove the 6 screws that secure the housing lid and temporarily remove the lid. Use the provided1�” self-drilling screws to secure the housing to the pool wall. Make sure to wrap the bond wire, thatexits the top of the housing, around one of the screws before tightening.

Endless Pool Performance Current Supplemental...

Documents

Transcript of Endless Pool Performance Current Supplemental...