SURFACE PROTECTION FORNORD DRIVE SOLUTIONS

EN

Intelligent Drivesystems, Worldwide Services

2 Surface protection for NORD drive solutions www.nord.com

We use the latest generation of high-solid paints, which reduces the emission of solvents far below the legally required limits. By complying with the VOC balance we make an important contribution to protecting the environment.

High solid paints contain a high proportion of solid material - up to 80% - and with a low solvent content of only approximately 20%, contribute considerably less environmental pollution than other industrial paints. The high-solid paints which we use combine the emission benefits of hydro paints with the functionality of solvent-based coating materials.

In addition, the lower solvent proportion allows very short drying times in production - a decisive advantage over water-based paint systems. The substrates materials for water-based paint systems have to be cleaned and de-greased with solvents before they are painted.

Ultimately, our customers benefit from faster production and delivery times.

Less solvents and greater efficiency

Energy efficiency as a company philosophy

PROTECTING THE ENVIRONMENT WITH HIGH-SOLID PAINT

NORD drive solutions are especially valued for their great energy efficiency. We also use the same optimisation standards for production in our factories.

SOLVENT REDUCTION

2.0 hours4.0 hours

DryingPainting

STANDARD Conventional system

MANKIEWICZHigh-Solid system

40 % Solids up to 80 % Solids

STANDARD Conventional system MANKIEWICZ High-Solid system

PROCESS OPTIMISATION

Our coating systems have been successfully tested by an independent laboratory:

n Cross cut test according to DIN EN ISO 2409 to test the adhesion of the paint system.n Salt spray test according to DIN EN ISO 9227 to test corrosion resistance.n Evaluation of degree of delamination according to DIN EN ISO 4628-8.

Optimum pro-tection for every application

3www.nord.com Surface protection for NORD drive solutions

COPING WITH CONTAMINATIONWITH THE RIGHT COATING SYSTEM

Our coating systems have been successfully tested by an independent laboratory:

n Cross cut test according to DIN EN ISO 2409 to test the adhesion of the paint system.n Salt spray test according to DIN EN ISO 9227 to test corrosion resistance.n Evaluation of degree of delamination according to DIN EN ISO 4628-8.

20 % Lösemittel

PROZESSOPTIMIERUNG

Coating Field of application Structure

2.0 C2 as per EN 12944Indoor installation

3.0C2 as per EN 12944For indoor installation and protected outdoor instal-lation (e.g. open, unheated halls)

3.1C3 as per EN 12944Outdoor installation, city and industrial atmosphere with low contamination

3.2C4 as per EN 12944Outdoor installation, city and industrial atmosphere with moderate contamination

3.3

C5 as per EN 12944Outdoor installation, city and industrial atmos-phere with high contamination, filling of all screw heads, holes and gaps.

3.4 For normall chemical contamination

3.5 For food packaging areas

Z Compensation of contour recesses and crevices with polyurethane sealantA Additional antimicrobial coating for all paints except 3.4 und 3.5

Coatings and their fields of application

4 Surface protection for NORD drive solutions www.nord.com

Throughout the world, NORD DRIVESYSTEMS offers you a uniform series of standard colours as well as preferred colours. In addition we also implement individual solutions according to your specifications, which optimally match the corporate design of your company.

Standard colours are held in stock in our painting facilities throughout the world and are therefore always available:

n RAL 7031 Blue-Greyn RAL 5010 Blue

Special colours according to RAL, BS, Munsell, Pantone or even according to colour samples can be supplied against extra charge.

CLEAN APPEARANCEIN YOUR CORPORATE COLOUR

Globally valid quality for your corporate identity

5www.nord.com Surface protection for NORD drive solutions

PRESERVE SAFETYWITH THE RIGHT TOP COAT

The paint systems used by NORD uses are resistant to chemicals. They have been tested for their resistance to all important substances which could have a negative environmental effect.

After full drying of the paint system, NORD paints are suitable for foodstuffs and fulfil the NSF / ANSI 51-2009e test criteria. No further top coats are required.

Antibacterial paints are possible for all paint systems. For this, a final clear lacquer containing antimicrobial silver ion particles (layer thickness approx. 40µm) is applied, which does not affect the colour.

Tested paint systems for special requirements

Because of their extremely robust and durable properties, powder coatings are very suitable for the electrical industry. Surfaces which are treated in this way are resistant to impact, scratches and wear. They are resistant to weather and chemicals and are even more robust than conventional NORD paints.

In the electrical industry, the anti-static properties of electrically conducting powder paints are relevant for the prevention of static charging of the drive units. Potential interference is eliminated and down time probability is minimised. The subject of environmental protection is becoming increasingly important in the field of surface coatings. Powder coating does not use solvents, but rather dry powder, which is melted onto the workpiece in a kiln.

Powder coating for decentralised drive technology

Environmentally friendly high per-formance coatings for SK 200E se-ries decentralised frequency inverters with IP66 protection class.

6 Surface protection for NORD drive solutions www.nord.com

THE ALTERNATIVE TO STAINLESS STEELnsd tupH SURFACE AND CORROSION PROTECTION

Geared motors from NORD with nsd tupH are the optimal choice for use in challenging environmental conditions.

n Easy to clean surfacesn Resistant to acids and alkalis

(wide pH range)n No spreading of corrosion, even if

damagedn No flakingn Corrosion resistant, prevents contact

corrosionn Alternative to stainless steeln Conforms to FDA Title

21 CFR 175.300n Free from chromates

The complete solution for extreme conditions

n Surface-treated housing componentsn DIN and standard components made

from stainless steeln Washdown housing (gear unit and

motor)

n Stainless steel shaftsn Special shaft sealing ringsn Food-compatible oil

nsd tupH for extreme requirements

n Food & beverage industryn Dairiesn Pharmaceutical industryn Water and sewage plantsn Car washesn Offshore and coastal areasn Cleaning with chemicals

(washdown, wide pH range)

Tests performed on surface-treated aluminium housing components:

n ASTM D714 Blister formationn ASTM D610-08 Corrosionn ASTM D1654-08 Scratchingn ASTM B117-09 Salt spray testn ASTM D3170 Gravelometer testn DIN EN ISO 9227 Salt spray mist testn DIN EN ISO 2409 Cross-cut test

NORD smooth motor with nsd tupH

Sealed Surface Conversion System

Products available with nsd tupH:

Helical gear units

Bevel gear units

Smooth motors

Electronic SK 1xxE

UNIVERSAL worm gear units

7www.nord.com Surface protection for NORD drive solutions

NORD DRIVESYSTEMS Group

Headquarters and Technology Centrein Bargteheide, close to Hamburg

Innovative drive solutionsfor more than 100 branches of industry

7 state-of-the-art production plantsproduce gear units, motors and inverters also for complete drivesolutions from a singlesource.

Subsidiaries and sales partners in 98 countries on 5 continentsprovide local stocks, assembly, production,technical support and customer service

More than 3,600 employees throughout the worldcreate customer oriented solutions

Gear unit production Motor production Inverter production

Gear units Motors Inverters, motors starters andfield distribution systems

Mechancial products Electronical productsElectrical products

The map image above is for information purpose and may not have been prepared or be suitable for legal purpose and we do not own any responsibility for correctness or authenticity of the same.

S34

00 M

at.-N

r. 60

6460

2 / 4

017

Headquarters:Getriebebau NORD GmbH & Co. KGGetriebebau-Nord-Straße 122941 Bargteheide, GermanyT +49 (0) 4532 / 289 - 0F +49 (0) 4532 / 289 - 22 53info@nord.com, www.nord.com

Member of the NORD DRIVESYSTEMS Group

NORD DRIVESYSTEMS GroupHeadquarters and Technology Centrein Bargteheide, close to Hamburg

Innovative drive solutionsfor more than 100 branches of industry

Mechanical productsparallel shaft, helical gear, bevel gear and worm gear units

Electrical productsIE2/IE3/IE4 motors

Electronic productscentralised and decentralised frequency inverters, motor starters and field distribution systems

7 state-of-the-art production plantsfor all drive components

Subsidiaries and sales partners in 98 countries on 5 continentsprovide local stocks, assembly, production, technical support and customer service

More than 3,600 employees throughout the worldcreate customer oriented solutions

www.nord.com/locator