EN IPL 8500 Instructions for use ...............................3

Electromagnetic Compatibility Information .................................................26

IPL 8500

READ THIS MANUAL COMPLETELY AND CAREFULLY BEFORE USING THIS PRODUCTKeep this manual in a safe location for future reference

3

1. What is IPL 8500

Indications for useThe IPL 8500 device is an over-the-counter device intend-ed for the reduction of unwanted body and/or facial hair. IPL 8500 is also intended for permanent reduction in hair

regrowth, defined as a long-term, stable reduction in hair regrow when measured at 6, 9, and 12 months after the completion of treatment regimen.IPL 8500 is a personal use device intended for the reduc-tion of unwanted hair.

ENGLISH

Table of Contents1. What is IPL 8500.............................................................. 32. Who should use the IPL 8500 and

how to decide to use IPL 8500 ....................................... 43. Benefits ........................................................................... 54. Who should NOT use the IPL 8500? ............................... 6

Who cannot use the IPL8500 - CONTRAINDICATIONS . 6What you must do to avoid serious harm – WARNINGS 7What you must do to avoid other harm – CAUTIONS .... 8

5. Possible Adverse Reactions ............................................ 96. IPL 8500 Description ..................................................... 11

Device Components ..................................................... 11User interface description ............................................. 12

7. User Instructions ........................................................... 14Preliminary Test ............................................................ 14Step 1: Device Set-Up .................................................. 15

Step 2: Prepare your skin ............................................ 15 Step 3: Device operation ............................................. 16 Recommended treatment protocol: ............................ 18 What to expect when using IPL 8500 ......................... 19 Step 4: Cleaning & Storage ......................................... 20

8. Post treatment care ..................................................... 20 9. Troubleshooting ........................................................... 2010. Warranty / service ........................................................ 2111. Device specification parameters ................................. 2212. Labeling ....................................................................... 2313. Electromagnetic compatibility (EMC) and

Specifications ............................................................. 2414. Treatment Log.............................................................. 25

4

IPL 8500 features the proprietary RPL™ technology (Re-active Pulsed Light).IPL 8500 is intended for home use environment.

RPL (Reactive Pulsed Light)™ technology - How does it workThe IPL 8500 is based on the scientific principle of select-ive photothermolysis.RPL™ (Reactive Pulsed Light) advanced technology uses IPL (Intense Pulsed Light) technology along with a combina-tion of unique skin condition sensors. The light penetrates the epidermis to the dermis and is absorbed by the melanin in the hair shaft. The heat generated by the absorbed light then dissipates into the follicle and generates local thermal damage, causing a reduction in hair growth.

Long-term hair reduction – Hair growth cycleTwo factors play an important role in optimal long-term hair reduction:• Hair growth cycle involves three phases: Anagen, Cata-

gen, and Telogen. Anagen is the growth phase, while Catagen and Telogen are the resting phases. Permanent hair reduction can only occur during the Anagen phase.

• Skin types (according to the Fitzpatrick scale) are illus-trated on the diagram below: Darker skin contains more melanin, which competes with the targeted hair for energy light absorption. When more light energy is ab-sorbed into the skin, there is a greater risk of adverse effects, and the epidermis may be damaged.

Please make sure to carefully read this user guide before you start treating with IPL 8500.

2. Who should use the IPL 8500 and how to decide to use IPL 8500

• IPL 8500 is intended for women and men who desire to reduce unwanted hair.

• IPL 8500 is intended for use on entire body (e.g. legs, arms, underarms, bikini line, back, shoulders and chest) and allowed facial areas (e.g. above upper lip, cheek, jaw, chin and neck).

• IPL 8500 is intended for use on skin tone type I to IV ac-cording to Fitzpatrick skin chart below.

5

I II III IV V

X

VI

XThe use of IPL 8500 on naturally dark skin is forbidden.

IPL 8500 works best on dark hair or hair that contains more melanin. Brown and light brown hair will respond, but typ-ically will require more treatment sessions. Red hair may show some response. White, grey or blond hair shows a more limited response. Nevertheless, some users have noted hair reduction after multiple treatment sessions.

Never use IPL 8500 around or near your eyes.

Note: IPL 8500 is especially designed for your own per-sonal treatment! It is intended for a single user only.

3. BenefitsSafety! With IPL 8500, your skin is in good hands.

IPL 8500 is based on RPL technology, including an auto-matic built-in skin color sensor that is designed to provide

you with complete safety and reassurance. The sensor con-tinually evaluates your skin tone and allows IPL 8500 to perform only on suitable areas. This smart safety feature automatically disables treatment if your skin is too dark or too tanned. As an extra precaution, the IPL 8500 has been designed to only emit a light pulse when it is in contact with your skin.

Convenience! The IPL 8500 can be operated in two treat-ment modes:• Pulse mode: ideal for initial device usage or for small or

curvy areas such as the knees, underarms and bikini line. Each press on the trigger button will release a pulse to the treatment area (the trigger button may be hold con-tinuously or pressed repeatedly).

• Trigger-less mode: perfect for large areas, such as the back and legs. After holding the trigger button until three consecutive pulses are released, or by pressing the “trig-ger-less mode” button ( ) the device will automatic-ally enter trigger-less mode. In this mode consecutive pulses will be released without the need to press the trigger button.

6

Chargeable! The IPL 8500 has a rechargeable battery. After charging your device, you can use it as cordless and enjoy a more flexible and convenient treatment.

Versatility! The IPL 8500 includes an additional precise treatment area window, especially designed for more ef-fective usage, allowing more precise treatments at differ-ent body areas.

Effective! For permanent reduction in hair regrowth, defined as a long-term, stable reduction in hair regrow when meas-ured at 6, 9, and 12 months you should follow treatment regimen. With the clinically proven IPL technology you may see some improvement already in 3-4 weeks, when using the device according to the recommended treatment proto-col described in this User Guide (see page 28). The hair will continue to grow up to two weeks after a hair reduction session. However, thereafter as the hair grows in three different stages it will naturally and gradually fall out, depending on the hair growth stage in during which the treatment was done (only hairs in the active growth phase will be affected). Some hair may not be affected by the IPL 8500 because of the different hair growth phases.

Response to IPL 8500 hair reduction differs between indi-viduals depending on biological factors and how closely treatment instructions are followed.

Note: Hair removal by lasers or intense pulse light sources can cause increased hair growth in some individuals. Based upon currently available data, the highest risk groups for this response are females of Mediterranean, Middle East-ern, and South Asian heritage treated on the face and neck.

4. Who should NOT use the IPL 8500?

IPL 8500 is designed especially for you, to be used over normal, healthy and intact skin, for both safe and effect-ive treatment. However, IPL 8500 is not appropriate for everyone. Please read the information below before use. If you still have any doubts, and you are unsure that the IPL 8500 is safe for your use, please consult with your per-sonal physician.

Who cannot use the IPL8500 - CONTRAINDICATIONSDo NOT use IPL 8500 device if you have any of the fol-lowing conditions:

7

• If you have an active implant such as a pacemaker, in-sulin pumps, or similar devices since it may cause inter-ference.

• If you are pregnant or with a slight chance of being preg-nant or nursing since it has not been established and may result in stimulation of pigmentation.

• If you have skin cancer or on areas at risk of malignancy or if you have received radiation therapy or chemother-apy within the past 3 months since it has not been es-tablished and the immune system can be compromised which can lead to serious injury.

• If you suffer from epilepsy, it could trigger seizure.• If you have damaged or broken skin or history of Herpes

or Psoriasis outbreak in the treatment area since it can result serious side effects.

• If you suffer from keloid scar (growth of extra scar tis-sue where the skin has healed after an injury) formation in the treatment area since it has not been established and may result serious skin complications.

• If you have been taking Tetracycline antibiotics and medi-cation with the following active ingredients within the last two weeks: Retinoid acid, Retina-A, Vitamin A such as Accutane as it is considered to be a photo-sensitive drug and may result serious skin injury.

• If you are photosensitive or have other diseases related to light sensitivity as it may lead to serious injury.

• If you suffer from severe or decompensated metabol-ic conditions, such as diabetes, since it may cause a greater risk of delayed healing and infection in the case of an adverse effect.

• If you have had a skin peel or other skin resurfacing pro-cedure within the last 8 weeks in the treatment area as it may result in stimulation of pigmentation.

Note: If you have undergone any other aesthetic procedures or any uncertainty regarding potential side effects, consult your physician before using the IPL 8500.

What you must do to avoid serious harm – WARNINGS• Do not use IPL 8500 on naturally dark skin (see guidance

at the back cover and high Fitzpatrick level in the “Who should use the IPL 8500 section”).

• Do not use the IPL 8500 if you have dark brown or black spots such as freckles, birth marks, around the nipples, moles or blisters on the area to be treated.

• Do not use the IPL 8500 on mucous membranes such as nostrils, lips of the mouth, eyelids, ears, genital area and the anus as it may lead to serious injury.

8

• Do not use the IPL 8500 over piercing or any metal items such as earrings or jewelry on the area to be treated as it may cause burns.

• Do not use the IPL 8500 over areas with tattoos or permanent makeup on the area to be treated.

• Never look directly at the light coming from the IPL 8500 applicator and lamp as it may cause eye injury.

• Never use flammable liquids such as alcohol (including perfumes, sanitizers, or other applications containing al-cohol) or acetone to clean the skin one hour before using IPL 8500 as it may cause burning of the skin.

• Do not use IPL 8500 on tanned skin or after sun ex-posure as this can cause serious burns or skin injury. Avoid more than 15 minutes of sun exposure for 4 weeks before your treatment and for at least 2 weeks post treatment. If during this period your treated skin area is exposed to sunlight, make sure to apply SPF 30 or higher sunscreens.

• Do not treat the same area of skin more than once per treatment as it may cause skin irritation.

What you must do to avoid other harm – CAUTIONS• KEEP OUT OF CHILDREN’S REACH.

• This appliance is not intended for use by persons with reduced physical, sensory or mental capabilities.

• Do not use this appliance near bathtubs, showers or other vessels containing water as it may lead to elec-trocution risk.

• Do not open or repair the device as it may expose you to dangerous electrical components which may cause serious bodily damage.

• Do not leave the device unattended while plugged into the electricity as it may lead to electrocution risk.

• Do not use the device if any part of the device or its ac-cessories are not working properly, appear damaged, broken, loose, missing, wet or if you see or smell smoke.

• Before using IPL 8500, make sure the device is clean, dry and intact. Cleaning instructions are detailed in the “Cleaning” chapter.

• Do not share device at any time, due to the possibility of transmitting diseases between users.

• Use IPL 8500 only with the supplied external power and accessories. For your safety, never use DC adapters which are not approved by the manu-facturer.

• Use the IPL 8500 device only according to the instruc-tion for use and the intended aesthetic use.

9

5. Possible Adverse ReactionsWhen using IPL 8500 device according to the instructions for use, adverse reactions are rare. However, every aesthetic procedure, including the usage of home-use devices, may cause some degree of adverse reactions (as listed in the table below). The possible adverse reactions are temporary, rare, and resolve spontaneously within few hours or days. In case adverse reactions appear, stop using the IPL 8500 device. Please consult your physician if necessary.

Degree of Side Effects Side Effects

MinorSide-Effects

Skin IrritationSkin RednessSkin Sensitivity

RareSide-Effects

Skin BurnsScarringPigment ChangesExcessive Redness and Swelling

Extremely Rare Side-Effects InfectionBruising

For your convenience, additional explana-tions are given below. Skin Irritation• The use of Pulsed Light Hair Removal System is gener-

ally very well-tolerated, the majority of users do feel a sensation of warmth and a mild stinging sensation dur-ing treatment or a few minutes after. Anything beyond this skin irritation – discomfort is abnormal and means that either the energy level is too high, or you shouldn’t continue using the IPL 8500 as you are unable to toler-ate the hair reduction application.

Skin Redness• Redness on the treated area may appear right after using

the application or within 24 hours of using the IPL 8500. Consult your physician in case the redness does not dis-appear within 2 to 3 days.

Skin Sensitivity• You may feel that your skin in the treated area is more

sensitive so you may encounter dryness or flaking of the skin.

Skin Burns• Rarely, burns on the treated area can occur following the

use of the hair removal system. The burns can require

10

a few weeks to heal and, extremely rarely, may leave a visible permanent scar.

Scarring• In rare cases, permanent scarring may occur. Usually

when scarring occurs it is in the form of a flat and white lesion on the skin (hypotrophic). However, it can be large and red (hypertrophic) or large and extend beyond the margins of the injury itself (keloid). Subsequent aesthet-ic treatments may be required to improve the appear-ance of the scar.

Pigment Changes • Use of the IPL 8500 may cause temporary skin hyper-

pigmentation (increased pigment or brown discoloration) or hypopigmentation (whitening) to the surrounding skin. The risk is higher for people with darker skin tones. Usu-ally discoloration or changes to skin pigment are tempor-ary and permanent hyperpigmentation or hypopigmen-tation rarely occur.

Excessive Redness and Swelling• Very rarely, the treated area skin may become very red

and swollen. This side effect is very common in sensi-tive areas of the body. The redness and swelling should be decreased after 2 to 7 days and you should treat the area by applying ice. You should avoid exposure to sun.

Infection• In rare cases, infection of the skin is a possible risk fol-

lowing a skin burns caused by the application.Bruising• Blue-purple bruising is exceedingly rare by using the IPL

8500 and can last 5 to 10 days. As the bruising fades, there may be a rust-brown discoloration of the skin (hyperpigmentation) that can be permanent.

11

6. IPL 8500 Description1

2

34

5

678910

11

12

Device ComponentsThe IPL 8500 device set consists of the following compon-ents, as demonstrated in the picture below: • Hand-held device• External power supply• Precise and Large Treatment windows

1. Status indicator: Lack of contact Non-allowed skin tone Error mode 2. Internal lamp 3. Treatment window 4. Skin tone and contact window (Fitzpatrick window) 5. Trigger button 6. 1-6 energy level lights 7. Battery status indicator 8. Increase energy level button 9. Decrease energy level button10. Trigger less mode button11. ON/OFF button12. Power supply socket

12

Large treatment window

Precise treat-ment window

Power adapter

User interface descriptionThe user interface and control capabilities include the fol-lowing features:1. ON/OFF button – The button activates and deacti-

vates your device by a single press. In addition, when the device is left unattended for 5 minutes, the device will automatically turn off. When turning on the device, all energy levels lights will light up for a split second, and then the device will turn on at energy level 1.

2. Trigger-less mode button – A press on the button will activate the trigger-less mode (‘glide mode’). In this mode, consecutive pulses will be released without the need to press the trigger button, as long as the device is in full contact with the skin and applied on allowed skin tone. The glide mode can be turned off by additional

press on the trigger-less button or will be automatically turned off if the device is unused (or doesn’t have proper skin contact and skin tone detected) for a few seconds.3. Energy selection buttons – The + (Increase energy

level) and – (Decrease energy level) buttons, al-lows energy level selection between 6 different lev-els. Choose the energy level according to your com-fort and as selected in the preliminary use test. a. Pressing the + or - buttons (after the device turns

on) will increase or decrease the energy by a single level. Each additional press will change the energy level, between the lowest level (indicated as “1”) to the highest (indicated as “6”). Note that when you reach the maximal energy level (“6”), pressing the + button again won’t change the energy level. Similarly, when you reach the min-imal energy level (“1”), pressing the – button won’t change the energy level.

b. The 1-6 energy level lights will light up Green ac-cording to the selected energy level (e.g. at energy level 1, one green light will be lit, at energy level 2, two green lights will be lit).

4. Battery status indicator - The indicator, marked as , shows the status of the battery charging:

a. Red – battery is being charged.

13

Note: if in addition to this red light, energy level “1” is green, the device is turned on.

b. Green - Battery is fully charged and the device is connected to the external power supply.

c. ‘slow’ blinking red – low battery level (about 30% of battery is charged).

d. ‘fast’ blinking red – low level of battery (about 10% of fully charged).

Note: the green or blinking red battery status indi-cators will appear only while the device is turned on.

5. Large Treatment window and Precise Treatment win-dow – for most comfortable treatment, select the ap-propriate treatment window per different body areas:

a. Large Treatment window (the optical filter is built-in the device) – use the IPL 8500 with the large treat-ment window for treatment of large body areas, such as legs, back and arms. Using this large window will make hair removal faster and easier.

b. Precise Treatment window (additional snap-on win-dow with red optical filter) – attach (just snap-on) the Precise Treatment window for treatment of small and delicate areas, such as face (below cheek line area) and bikini line.

6. Status indicator light – this indicator (located at the back side of the device) has several statuses, as detailed in the table below:

Indicator Mode

“Steady”green light

On A pulse is ready. While pulse is delivered or be-tween pulses, no light ap-pears.

“Momentary”orange light

Activation (pulse) is blocked

The device does not deliv-er a pulse due to the lack of full skin contact.

“Momentary”Red light

Activation (pulse) is blocked

The device does not de-liver a pulse due to non-al-lowed skin tone (high Fitz-patrick level as described at the back cover of the User Guide).

“Blinking”orange light

Close to end of life

Indicates about the close end of the lamp life time.

14

“Steady”red light

End of life/blocked

Device is permanent-ly blocked, the lamp has reached its maximum flash limit or internal malfunc-tion has been occurred or the treatment area window is not properly attached to the device.

7. User InstructionsIPL 8500 is an optimal solution for all body areas such as your underarms, bikini line, arms, back, shoulders, chest, legs and allowed facial areas such as above upper lip, cheek, jaw, chin and neck.

Preliminary Test The preliminary test is intended to determine your skin’s re-action to the IPL 8500 treatment and help you set the opti-mal energy level for each treatment area. Do a preliminary test on each area you intend to treat 48 hours prior to the first full treatment. Note: Do not treat full areas with energy levels that you have not tested before!

Do not treat the tested area for at least 48 hours after the preliminary test is done.1. Set up the device as indicated in the “Step 1: Device set

up” section and prepare your skin (as described in “Step 2: Prepare your skin”).

2. Select the lowest energy level and deliver a pulse on the selected preliminary test skin area.

3. If you feel comfortable with the energy level, increase it to level 2 and perform an additional pulse on the next spot.

4. Only if you feel comfortable, you may reach the maximum energy level (6th).

5. Stop the test once you do not feel comfortable, as in-creasing the energy level increases the risk of adverse effects.

6. If you see adverse effects such as severe redness or blis-tering - stop the test immediately.

7. Wait 48 hours and examine the tested area. • If the skin in the test area seems normal (no response

or mild redness observed), you can proceed with a full treatment in the highest comfortable energy level that you tested.

• If you see extreme redness, swelling, or blistering even in the low-energy level settings, do not proceed to the full treatment in that area.

15

Step 1: Device Set-Up1. Remove all components from the box (handheld device,

desired treatment window and power supply).2. Make sure the device is clean, dry, and intact. 3. Select the desired treatment window and simply snap it

onto the light exit window.Note: the device will not operate without the treatment win-dow or if the treatment window is not properly attached.

4. Charge your IPL 8500 device, as necessary.• Before your first use and when the battery is empty,

fully charge the IPL 8500 battery (full charging of the battery takes up to 2.5 hours).

• Whenever battery level is low, as indicated by the blink-ing red light at the Battery status indicator, recharge your device.

• Fully charge the appliance every 3 to 4 months, even if you did not use the appliance.

• For charging your device, insert the power cord into the socket and the power supply into the wall socket. When the battery is fully charged, the charging light lights up green continuously.

• After charging, remove the power adapter from the wall socket and disconnect it from your device.

Notes: • Some warming of the device and power adaptor during

charging is normal.• Charging should be done in a room temperature or cool

environment, never above 104°F (40°C). The device is equipped with battery-overheat protection and will not charge if the room temperature exceeds 104°F (40°C).

• Never cover the appliance and the adapter during char-ging.

• You can use the device while it is being charged. This may allow you limited number of pulses since battery charging is slower then battery consump-tion during use.

The IPL 8500 is now ready to be used.

Step 2: Prepare your skin1. Remove all jewelries from treatment area.2. Make sure your skin at the treatment area is shaved or

trimmed and cleaned from any residue such as pow-ders, creams, makeup, antiperspirants or deodorants.

3. Between treatments, you can shave but don’t wax or pluck hair.

4. Never use flammable liquids such as alcohol (including perfumes, sanitizers, or other applications containing al-

16

cohol) or acetone to clean the skin one hour before using the device as it may cause burning of the skin.

5. Do a preliminary test on a small patch of skin in the in-tended treatment area, 48 hours prior to first use of the IPL 8500 to determine energy level settings for your treat-ment (as depicted in the preliminary test section).

Important: Do not use any cream or gel while using the device since it may dirt your device and prevent its nor-mal operation.Remember: The IPL 8500 comes with a built-in skin-tone sensor, enabling the application only on a suitable skin tone. This unique safety feature will not let you treat areas where your skin is too dark or too tanned, even if your general skin type is lighter.

Step 3: Device operationNote: A preliminary test should be conducted before pro-ceeding to a full treatment. See “preliminary test” section above.1. Prepare your skin (see step 2).2. To turn the IPL 8500 device on, press the ON/OFF but-

ton ( ). Energy level 1 green indicator will light on. The device sets itself on the lowest energy level—level 1. For

other energy levels press the increase energy level but-ton (+) or decrease energy level button (-).

3. You may decrease or increase the energy level accord-ing to your convenience (to reach the level determined in the preliminary test section). The energy level indica-tor lights will light up green according to the selected energy level, one green light for energy level 1, two lights for energy level 2, etc.

4. Place the IPL 8500 treatment window on the desired body area with full contact with the skin. • If IPL 8500 is not properly applied, the status indicator

will be “momentary” orange. • If your skin tone is too dark/ tanned, the status indicator

will be “momentary” red. In these cases, the IPL 8500 will not trigger a pulse in that area of skin.

5. Press the device window gently against your skin to be treated to ensure proper contact and use the trigger but-ton to release a pulse (make sure all treatment window is in contact with the skin). Start moving the device with each pulse to the next spot, while the device is detached or not with your skin, according to your comfort. When the pulse will be released, you will see a bright flash, you will hear a popping noise, and you may feel a mild sting-ing and/or heat sensation. After each pulse, the device will immediately recharge and will be ready for the next

17

pulse. You may choose from 2 treatment modes, either the ‘pulse mode’ or the ‘trigger-less mode’:

a. Pulse mode: Press the trigger button once for release of a pulse to the treatment area. After moving to the next spot to be treated, press the trigger button again to release another pulse. The trigger button may be either pressed or continuously held.

b. Trigger-less mode (glide mode): Begin treatment in the ‘pulse mode’. After three consecutive pulses without releasing the trigger button are released, or after pressing the trigger-less button, the device will automatically enter into the trigger-less mode and al-low continuous consecutive pulses release without the need to press or hold the trigger button. In trig-ger-less mode, the device will automatically deliver a pulse (without holding the trigger button) when a pulse is ready (1-3 seconds after the previous pulse) and when proper skin tone and contact are detected by the skin tone and contact sensor. If activated by the trigger-less button, the glide mode can be turned off by additional press on the button or will be auto-matically turned off if the device is unused (or doesn’t have proper skin contact and skin tone detected) for a few seconds. If activated by constant press on the trigger button, the glide mode will be automatically

deactivated when the device is not in proper contact with the skin or when skin is too dark/ tanned.

6. After the treatment, turn off the device by pressing the “ON/OFF” button; an orange indicator will light up while the device is in the shutdown mode.

7. Perform treatment sessions according to the “Recom-mended treatment protocol” section.

Important notes: • Try not to overlap pulses on the same spot of skin. Re-

peated pulses on the same spot may cause burns. • Do not treat the same area of skin more than once per

treatment as it may cause skin irritation.• IPL 8500 will not trigger a pulse if: a. There is no full contact of the treatment window with

the skin b. Your skin tone is too dark or tanned

18

Recommended treatment protocol:Treatment areas depending on hair color and their treatment protocol:

Hair Color Fitzpatrick Skin Level

Energy Levels Treatment Area Average Number of Treatments

Treatment Interval

Light Brown to Brown

I–IV (Inclusive) 1–6 Legs 10–12 The 1–4 treatments will be approximately two weeks apart, fol-lowed by four-week time intervals.

Arms

Underarms

Bikini Lines

Brown to Black I–IV (Inclusive) 1–6 Legs 8–10

Arms

Underarms

Bikini Lines

Important: Facial treatment should be performed at 1-4 energy levels only.Don’t forget to select the proper treatment window (either the large Treatment Window or the additional small Precise Treatment window), according to the size of the treatment area and your comfort.

Plan your IPL 8500 treatmentEnergy level should primarily be chosen based on your own comfort.The energy levels vary from level 1 to level 6 with a light flu-ence of 2-5 [J/cm2].

19

Each treatment pulse should be applied on different skin spot with no repetition or overlap. The entire treatment area (underarms, bikini line, arms, back, shoulders, chest, legs and allowed facial areas) will be determined by the user.Notes: • Response to IPL 8500 hair reduction differs between in-

dividuals, depending on their unique biological factors.• It may take up to 3-4 weeks before results of the IPL

8500 treatment can be seen. The hair will continue to grow up to two weeks after a hair reduction session. However, thereafter as the hair grows in three different stages the hairs will naturally and gradually fall out de-pending on the hair growth stage in during which the treatment was done (only hairs in the active growth phase will be affected). Some hair may not be affect-ed by the IPL 8500 because of the different hair growth phases. To remove this hair multiple treatment sessions are required to reach the desired result.

• The number of sessions required for achieving long term results is different for every treatment area and changing for every user, as it is affected by type of skin, hair and hormonal changes.

• Red hair may show some response. White, grey or blond hair shows a more limited response. Nevertheless, some

users have noted hair reduction after multiple treatment sessions.

• IPL 8500 is suitable for men. However male body hair, especially those on the chest will require more hair re-duction sessions.

• Maintenance will be needed from time to time if growth is still visible.

• You may use the treatment log at the end of this manual, in order to assist you with recording your specific treat-ments areas, dates and duration.

What to expect when using IPL 8500During your hair removal treatment it is normal to experi-ence:• A flash of light on each press of the trigger button. The

light will not harm the eyes. • A pop noise with each pulse – occurs whenever a pulse

is activated.• A sensation of warmth – radiates from the light energy

after each pulse.• A mild stinging sensation – can be felt, similar to being

snapped with a rubber band.Some mild red or pink color may appear during or just after using the IPL 8500.

20

Step 4: Cleaning & Storage1. Make sure to turn off and unplug unit before cleaning.2. It is recommended that the treatment window area will be

cleaned after every session by using a dry, clean cloth to gently wipe the device.

3. Keep the device dry. Never place, store or use IPL 8500 near bathtubs, showers, basins or other vessels con-taining water as this may cause severe electrocution.

4. If you do not plan on using your IPL 8500 for a long period of time, it is recommended to keep it clean and stored.

5. If you plan to travel and take your IPL 8500 with you, you should store it in the original box and follow this section.

8. Post treatment care• Apply a calming lotion such as Aloe Vera.• Avoid using peeling and bleaching creams or similar

products for at least 24 hours, as this irritates the treat-ed skin.

• Avoid direct sun exposure for at least 2 weeks post treat-ment. If recently treated skin is exposed to sunlight in this time period, make sure to apply SPF 30 or higher sunscreen.

• Do not wax or pluck hairs from treated areas between treatment sessions.

9. Troubleshooting• If you experience any problems with the IPL 8500, please

refer to below information to try to resolve it.• If the IPL 8500 does not turn on, make sure that the de-

vice is charged (as indicated by the green light at the battery status indicator).

• If IPL 8500 does not trigger a pulse:a. the treatment window is properly attached to your de-

vice (the device will not be operable if the treatment window is not attached or not properly attached to the device.

b. the device did not automatically exit trigger-less mode after proper contact and skin tone were not detected.

c. there is full contact with the skin. The trigger button will activate a flash pulse only when the device is in full contact with the skin.

d. the area you are trying to treat is not too small, curved or bony to treat. You should get the whole treatment window to touch the treatment area (try to pull the skin flat).

e. if the skin color level identified by IPL 8500 is too dark, the flash activation will be blocked. This situation is indicated by a “momentary” red light on the device.

21

f. in the case of a safety issue or when the lamp has reached its end, a steady red light will come on. The device will shut down.

• General error:a. In case of dirt or debris is stuck on the treatment win-

dow, you should clean the treatment window accord-ing to the cleaning section. If you can’t get the area clean, contact our Customer Service.

b. In case of a delay in pulse after repositioning the de-vice on different treatment area, you should consider working on cooler environment. The device may pulse at a slower rate in a warm environment.

c. In case of a general error, reset the device – turn the device off, wait 10 sec and then reconnect it.

• If you still have problems with your device, please con-tact our customer service.

10. Warranty / serviceBeurer GmbH, Söflinger Straße 218, 89077 Ulm, Germany (hereinafter referred to as “Beurer”) provides a warranty for this product, subject to the requirements below and to the extent described as follows.

The warranty conditions below shall not affect the sell-er’s statutory warranty obligations which ensue from the sales agreement with the buyer. The warranty shall apply without prejudice to any man-datory statutory provisions on liability.

Beurer guarantees the perfect functionality and complete-ness of this product.

The worldwide warranty period is 3 years, commencing from the purchase of the new, unused product from the seller.

The warranty only applies to products purchased by the buyer as a consumer and used exclusively for personal pur-poses in the context of domestic use.German law shall apply.

During the warranty period, should this product prove to be incomplete or defective in functionality in accordance with the following provisions, Beurer shall carry out a repair or a replacement delivery free of charge, in accordance with these warranty conditions.

If the buyer wishes to make a warranty claim, they should approach their local retailer in the first instance: see the attached “International Service” list of service addresses.

22

The buyer will then receive further information about the processing of the warranty claim, e.g. where they can send the product and what documentation is required.

A warranty claim shall only be considered if the buyer can provide Beurer, or an authorised Beurer partner, with - a copy of the invoice/purchase receipt, and - the original product.

The following are explicitly excluded from this warranty: - deterioration due to normal use or consumption of the

product;- accessories supplied with this product which are worn out

or used up through proper use (e.g. batteries, recharge-able batteries, cuffs, seals, electrodes, light sources, at-tachments and nebuliser accessories);

- products that are used, cleaned, stored or maintained im-properly and/or contrary to the provisions of the instruc-tions for use, as well as products that have been opened, repaired or modified by the buyer or by a service centre not authorised by Beurer;

- damage that arises during transport between manufac-turer and customer, or between service centre and cus-tomer;

- products purchased as seconds or as used goods;

- consequential damage arising from a fault in this product (however, in this case, claims may exist arising from prod-uct liability or other compulsory statutory liability provi-sions).

Repairs or an exchange in full do not extend the warranty period under any circumstances.

ManufacturerHome Well Trading Ltd.Omar Hodge BuildingRoad town, TortolaVG 1110 British Virgin Islands

Made in China.

11. Device specification parame-ters

Emitted light spectrum: Large treatment window (yellow optical filter) 475[nm] to 1,200[nm] max. Precise treatment window (red optical fil-ter) 550[nm] to 1,200[nm] max.Maximal emitted energy flux: 5 [J/cm²]

23

Selectable energy levels: 6 levelsTreatment area: Large treatment window: 0.7 sq inch (4.5cm²). Precise Treat-ment window (additional attachment): 0.3 sq inch (2cm²) Speed: 1 pulse every 3 seconds External Power Supply: 12[V], 1.8[A] 100–240 VAC, 50/60HzDevice Size and Weight: 16.3 [Oz], 7.9 X 6.9 X 2.7 [in] 461 [gr], 200 X 175 X 70 [mm] Technology: Home use IPL

Storage Instructions:

Storage and Transport Conditions

Temperature Humidity Pressure: 14ºF to 158ºF (-10ºC to 70ºC)0 to 90% RH at 131ºF (55ºC)non-condensing

Operational Condi-tions

Temperature Humidity Max operating altitude:50ºF to 104ºF (10ºC to 40ºC)30% to 70% RH10,000 ft.

Package includes: hand-held device, large treatment win-dow, precise treatment window power adaptor and user guide.

12. LabelingModel: IPL8500

Double insulation

Type BF equipment

Consult Instructions for use

Do not dispose

24

Keep away from eyes

Please read all warnings and safety pre-cautions prior to use

Do not use the IPL 8500 device on tanned skin or after sun exposure

Do not let the device become wet. Keep away from bathtubs, showers, basins, or other vessels containing water: Keep dry

Li-Ion

Rechargeable battery

IP 22 IP2X: Object of 12.5 mm diameter, shall not penetrate.IPX2: Vertically falling drops shall have no harmful effects.

14°F(-10°C)

158°F(70°C)

90%

0%

Storage Permissible storage temperature and humidity

Operating

50°F(10°C)

104°F(40°C)

70%

30%

Permissible operating temperature and humidity

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference.(2) This device must accept any interference received,

including interference that may cause undesired operation.

Use IPL 8500 only with the supplied external power and accessories. For your safety, never use DC adapters which are not approved by the manufac-turer.

13. Electromagnetic compatibility (EMC) and Specifications

• The IPL 8500 needs special precautions regarding EMC and needs to be installed and put into service according to the EMC information provided.

• Portable and mobile RF communications equipment can affect IPL 8500.

• The use of accessories or replacement parts, other than those sold/specified by sensica International, may re-sult in increased emissions or decreased immunity of the IPL 8500.

25

Subj

ect t

o er

rors

and

cha

nges

.

• The IPL 8500 should not be used adjacent to or stacked with other equipment and that if adjacent or stacked use is necessary, the IPL 8500 should be observed to verify normal operation in the configuration in which it will be used.

• Portable RF communications equipment, including an-tennas (including peripherals such as antenna cables and external antennas) should be used no closer than 12 inches (30 cm) to any part of the device including cables specified by the manufacturer. Otherwise, degradation of the performance of this equipment could result.

14. Treatment Log

Treatment Date Treated Area Comments

26

EMC InformationTable 1

IEC 60601-1-2: 2014 4th EditionThe device is intended for use in the electromagnetic environment specified below. The customer or the user of the device should assure that it is used in such an environment.Emissions test Compliance Electromagnetic environment – guidanceRF emissions CISPR 11 Group 1 The device uses must emit electromagnetic energy in order to perform its intended

function. Nearby electronic equipment may be affected.RF emissions CISPR 11 Class B The device is suitable for use in all establishments, including domestic establish-

ments and those directly connected to the public low voltage power supply network that supplies buildings used for domestic purposes.

Harmonic emissionsIEC 61000-3-2

Class A

Voltage fluctuations/flicker emissionsIEC 61000-3-3

Complies

27

Table 2

IEC 60601-1-2: 2014 4th EditionThe device is intended for use in the electromagnetic environment specified below. The customer or the user of the device should assure that it is used in such an environment.Immunity test IEC 60601 test level Compliance level Electromagnetic environment – guidance

Electrostatic discharge (ESD) IEC 61000-4-2

± 8 kV contact± 2, 4. 8, 15 kV air

± 8 kV contact± 2, 4. 8, 15 kV air

Floors should be wood, concrete or ceramic tile. If floors are covered with synthetic materi-al, the relative humidity should be at least 30%.

Electrical fast transient/burstIEC 61000-4-4 ± 2 kV for power supply lines ± 2 kV for power supply lines Mains power quality should be that of a typical

commercial or hospital environment.

Surge IEC 61000-4-5 ± 1 kV differential mode± 2 kV common mode c Mains power quality should be that of a typical

commercial or hospital environment.

Voltage dipsVoltage InterruptionsIEC 61000-4-11

0% UT ,0,5 cycle0% UT , 5 cycles70% UT ,30 cycles0% UT ‘300 cyles

0% UT ,0,5 cycle0% UT , 5 cycles70% Uv ,30 cycles0% UT ‘300 cyles

Mains power quality should be that of a typical commercial or hospital environment. If the user of the device requires continued operation duri-ng power mains interruptions, it is recommen-ded that the device be powered from an unin-terruptible power supply or a battery.

Power frequency(50/60 Hz) magnetic fieldIEC 61000-4-8

30 A/m 30 A/mPower frequency magnetic fields should be at levels characteristic of a typical location in a typical commercial or hospital environment.

NOTICE: UT is the a.c. mains voltage prior to application of the test level.

28

Table 3

IEC 60601-1-2: 2014 4th EditionThe device is intended for use in the electromagnetic environment specified below. The customer or the user of the device i should assure that it is used in such an environment.Immunity test IEC 60601 Test

LevelCompliance level

Electromagnetic environment – guidance

Conducted RFIEC61000-4-6

Radiated RFIEC 61000-4-3

3Vrms0.15 MHz to 80 MHz

6Vrms in ISM and amateur radio bands between0.15 MHz to 80 MHz

80% AM at 1kHz

10 V/m80 MHz to 2.7 GHz80% AM at 1kHz

3Vrms0.15 MHz to 80 MHz

6Vrms in ISM and amateur radio bands between0.15 MHz to 80 MHz

80% AM at 1kHz

10 V/m80 MHz to 2.7 GHz80% AM at 1kHz

Portable and mobile RF communications equipment should be used no closer to any part of the device including cables, than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter.Recommended separation distance

d = 3.5/3 =1.17

d = 3.5/6 =0.25

d = 3.5/10 =0.35 80 MHz ¿ 800 MHz

d = 7/10 =0.70 800 MHz ¿ 2.7 GHz

Where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer and d is the recommended separation distance in metres (m).Field strengths from fixed RF transmitters, as determined by an electromagnetic site survey,a should be less than the compliance level in each frequency range.b

Interference may occur in the vicinity of equipment marked with the following symbol:

29

NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies.NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures,

objects and people.a Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur radio, AM

and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the location in which the device is used exceeds the applicable RF compliance level above, the device should be observed to verify normal operation. If abnormal performance is observed, additional measures may be necessary, such as re-orienting or relocating the device.

b Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.

30

Table 4

IEC 60601-1-2: 2014 4th EditionRecommended separation distances between portable and mobile RF communications equipment and the device. The device is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the device can help prevent elec-tromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and the device as recommended below, according to the maximum output power of the communications equipment.

Rated Maximum Output Power of Transmitter

(W)

Separation distance according to frequency of transmitter (m)0.15 MHz to 80 MHz

d = 3.5/3 =1.17

80 MHz to 800 MHz

d = 3.5/6 =0.25

80 MHz to 800 MHz

d = 3.5/10 =0.35

800 MHz to 2,7 GHz

d = 7/10 =0.70 0.01 0.12 0.058 0.035 0.070.1 0.37 0.18 0.11 0.221 1.17 0.58 0.35 0.710 3.70 1.83 1.11 2.21

100 11.67 5.8 3.5 7For transmitters rated at a maximum output power not listed above, the recommended separation distance d in meters (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer.NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures,

objects and people.

31

IEC 60601-1-2: 2014 4th EditionTest specifications for ENCLOSURE PORT IMMUNITY to RF wireless communications equipment

Test Frequency(MHz)

Band a) (MHz)

Servicea) Modulationa) Maximum Power(W)

Distance(m)

Immunity Test Level

(V/m)

Compli-ance Level

(V/m)

385 380-390 TETRA 400 Pulse modulationb) 18 Hz

1.8 0.3 27 27

450 430-470 GMRS 460FRS 460

FM c) ± 5 kHz deviation

1 kHz sine

2 0.3 28 28

710704-787 LTE Band 13, 17

Pulse modulationb) 217 Hz

0.2 0.3 9 9745780

810

800-960

GSM 800/900,TETRA 800,iDEN 820,

CDMA 850,LTE Band 5

Pulse modulationb) 18 Hz

2 0.3 28 28

870

930

1720

1700-1990

GSM 1800;CDMA 1900;GSM 1900;

DECT;LTE Band 1, 3,4, 25; UMTS

Pulse modulationb) 217 Hz

2 0.3 28 28

1845

1970

32

575.

81_I

PL85

00-V

elve

tSki

nPro

_201

9-09

-02_

01_I

M_K

SA_E

N

Distributed by:Beurer GmbHSöflinger Straße 21889077 Ulm, Germany www.beurer.com

2450 2400-2570

Bluetooth,WLAN

802.11 b/g/n,RFID 2450,LTE Band 7

Pulse modulationb) 217 Hz

2 0.3 28 28

5240

5100-5800 WLAN 802.11 a/n

Pulse modulationb) 217 Hz

0.2 0.3 9 95500

5785

NOTE: If necessary to achieve the IMMUNITY TEST LEVEL, the distance between the transmitting antenna and the ME EQUIPMENT or ME SYSTEM may be reduced to 1 m. The 1 m test distance is permitted by IEC 61000-4-3a) For some services, only the uplink frequencies are included. b) The carrier shall be modulated using a 50 % duty cycle square wave signal. c) As an alternative to FM modulation, 50 % pulse modulation at 18 Hz may be used because while it does not represent actual modulation, it would be worst case.a) For some services, only the uplink frequencies are included. b) The carrier shall be modulated using a 50% duty cycle square wave signal.c) As an alternative to FM modulation, 50% pulse modulation at 18 Hz may be used because while it does not represent actual modulation, it

would be worst case.