EN 12668-2 Certified ProbesUltrasonic flaw detection probes meet all requirements of European standard EN 12668-2.

EN probes are suitable for use in a broad range of appli-cations and in all industry segments. They are particularly beneficial for the critical requirements of the Power Generation and Aerospace industries, with the following benefits:

• Full compliance with European standard EN 12668-2, data sheet included with each probe

• Superior quality and repeatability for accurate and consistent inspection results

• Permanently documented performance, lost data can be replaced from our database

• Detailed 4-page Certificate of Calibration available as an option - PZ-EN (order no. 59969).

The results of an ultrasonic inspection are only as reliable as the probe that is used to perform the test. The perfor-mance of a high quality probe must be

• accurate relative to its nominal specifications

• reproducible and consistent among probes of the same type.

To assure high quality and consistency among flaw detec-tion probes, the European Committee for Standardization (CEN) has ratified standard EN 12668-2, “Non-destructive testing - Characterization and verification of ultrasonic examination equipment – Part 2: Probes.”

GEInspection Technologies Ultrasonics

Digital | Eddy Current | Film | Testing Machines | Ultrasonics | X-ray

Straight Beam Probes

Type Order No. Element Ø (mm)

Frequency (MHz)

Distance Range (mm)

Contact Face

B 1 S ENB 2 S ENB 4 S ENMB 2 S ENMB 4 S EN

500035500036500037500038500039

2424241010

12424

70 - 120023 - 300015 - 300030 - 80015 - 1500

exchangeable protective membraneexchangeable protective membraneexchangeable protective membraneexchangeable protective membraneexchangeable protective membrane

K 2 G ENK 4 G EN

500071500072

2424

24

10 - 4000 7 - 8000

hard, wear resistant contact facehard, wear resistant contact face

K 5 K ENK 10 K EN

500061500062

5 5

510

5 - 2100 2 - 3000

hard, wear resistant contact facehard, wear resistant contact face

MB 4 F EN 500073 10 4 6 - 5000 hard, wear resistant contact face

EN 12668-2 Certified Probes

TR-Straight Beam Probes

Type Order No. Element (mm)

Frequency (MHz)

Distance Range (mm)

Remark

SEB 2 ENSEB 2-0° ENSEB 4 ENSEB 4-0° EN

500063500065500064500066

7 x 187 x 186 x 206 x 20

2 2 4 4

2 - 1000 4.5 - 2000 1.5 - 2000 4 - 4000

common inclination angle of both elements is 0°

common inclination angle of both elements is 0°

MSEB 2 ENMSEB 4 EN

500067500068

Ø 113.5 x 10

2 4

2 - 400 1 - 1500

SEB 4 KF 8 ENSEB 10 KF 3 EN

500069500070

Ø 8

Ø 5

410

0.8 - 400 0.3 - 140

Angle Beam Probes

Type Order No. Element (mm)

Frequency (MHz)

Distance Range (mm)

Beam Angle

WB 35-2 ENWB 45-2 ENWB 60-2 ENWB 70-2 ENWB 35-02 ENWB 45-02 ENWB 60-02 EN

500054500055500056500057500058500059500060

20 x 2220 x 2220 x 2220 x 2220 x 2220 x 2220 x 22

2 2 2 2 2 2 2

15 - 270010 - 2700 6 - 2500 5 - 220015 - 270010 - 2700 6 - 2500

38°45°60°70°38°45°60°

MWB 35-2 ENMWB 45-2 ENMWB 60-2 ENMWB 70-2 ENMWB 35-02 ENMWB 45-02 ENMWB 60-02 ENMWB 35-4 ENMWB 45-4 ENMWB 60-4 ENMWB 70-4 ENMWB 45-J5 ENMWB 60-J5 ENMWB 70-J5 EN

500040500041500042500043500044500045500046500047500048500049500050500051500052500053

8 x 9 8 x 9 8 x 9 8 x 9 8 x 9 8 x 9 8 x 9 8 x 9 8 x 9 8 x 9 8 x 910 x 1010 x 1010 x 10

2 2 2 2 2 2 2 4 4 4 4 5 5 5

10 - 3300 5 - 3300 4 - 2900 4 - 240010 - 3300 5 - 3300 4 - 2900 7 - 5000 3 - 4600 3 - 4600 3 - 4200 3 - 4600 3 - 4600 3 - 4200

38°45°60°70°38°45°60°38°45°60°70°45°60°70°

©2005 General Electric Company. All Rights Reserved. GEIT-20110GB (03/05)We reserve the right to technical modifications without prior notice.

GEInspectionTechnologies.com