7/29/2019 Emitter Transistor Amplifier Vjezba

http://slidepdf.com/reader/full/emitter-transistor-amplifier-vjezba 1/4

Common Emit ter Transis tor Amp l i fier  

CIRCUIT 

TRCE.CIR Download the SPICE file 

Here’s a classic circuit that’s still an essential building block of circuits today, both IC

and discrete.

VOLTAGE GAIN 

Suppose you’re asked to design a transistor amplifier for a voltage gain of 3. The gain

from the base to the collector can be approximated by the collector resistance over the

emitter resistance.

where RC’ is the AC resistance seen by the collector, RC|| RL, and RE’ is the AC

resistance seen by the emitter, RE1. Why include RE2 in the circuit if its AC bypassed by CE? The emitter resistance performs 2 functions: RE1 influences the AC voltage

gain and RE1+RE2 controls the DC bias. (More on bias below.)

With minimal loading (RL=100K), the voltage gain is Vc / Vb = -RC / RE1 = -1800 /

600 = -3. Run a simulation and view the transient response at the base V(3) and

collector V(4). Did the circuit achieve its expected gain?

7/29/2019 Emitter Transistor Amplifier Vjezba

http://slidepdf.com/reader/full/emitter-transistor-amplifier-vjezba 2/4

 

HANDS-ON DESIGN You can Increase the gain by choosing a smaller RE1 such as

300 ohms. The gain should increase to -1800 / 300 = -6.But don’t run a simulation yet!

Maintain the same bias condition by increasing RE2 to 900 ohms so that RE1 + RE2 =

1200 ohms. Run a new simulation. Did the circuit achieve its expected gain?

OUTPUT SWING LIMITS 

CIRCUIT ANALYSIS How far can you drive the output voltage before it significantly

distorts? Increase the sinewave amplitude from 0.2 to 0.5 V peak, for example, by

editing the VS statement to look like

VS 1 0 AC 1 sin(0 0.5 10kHz)

Rerun a simulation and check the output swing at V(4). Keep increasing the sine wave

amplitude till the output distorts. What is the output swing capability of the amplifier?

FREQUENCY RESPONSE 

Over what frequency range can you use this amplifier? The “AC  1” in the VS

statement generates a voltage source of 1VRMS for the AC (frequency) sweepanalysis. To check the response of the entire amplifier, sun a simulation and plot the

AC results at V(7).

CIRCUIT ANALYSIS What are the lower, fL ,and upper, fU, cutoff frequencies of the

amplifier? These are the points where the gain falls to 0.707 of the midband gain. For 

example, if your midband gain is 6, your cutoff frequencies occur where the gain

decreases to 6 x 0.707 = 4.24 V/V. The bandwidth of your circuit is simply fBW = fU

 – fL.

HANDS-ON DESIGN Suppose your application must pass 10 kHz but ignore 60 Hz

interference. Does the bandwidth of this amplifier include 60Hz? You can change the

lower cutoff frequency fL by adjusting C1. C1 forms a time constant with RS and the

input impedance of the amplifier. What value of C1 is needed to reduce the 60 Hz

response to about 1/10 of the midband gain while still passing the 10 kHz frequency?

7/29/2019 Emitter Transistor Amplifier Vjezba

http://slidepdf.com/reader/full/emitter-transistor-amplifier-vjezba 3/4

 

BIAS POINT 

SPICE calculates the small signal bias point (initial voltages) and places the result in

the output (*.out) file. View this file by selecting View > Output File from theWindows menus. The voltages are listed in a table by node and voltage.

CIRCUIT ANALYSIS Two parameters determine the collector current of the CE

amplifier: the emitter voltage (node 5) and total emitter resistance, Ic = V(5) / (RE1 +

RE2). What is the initial voltage at V(5) and initial collector current?

SIMULATION NOTE 

 Note that the transistor Q1 requires more parameters than a resistor or capacitor. The

Q1 statement “Q1 4 3 5 Q2N2222” includes a model name Q2N2222. The model

name refers to the model statement which specifies the parameters that describe the

transistor's behavior. The device parameters are typically generated by the

manufacturer and made available on their web site.

You may see an NPN model that does not specify all of the parameters. The unlisted

 parameters will be assigned their default values. For example, a transistor with all

default parameters except current gain BF=150 is described as

.model QXXXX NPN(BF=150)

SPICE FILE 

Download the file or copy this netlist into a text file with the *.cir extention.  

TRCE.CIR - TRANSISTOR COMMON EMMITER

*

VS 1 0 AC 1 SIN(0 0.2 10KHZ)

VCC 10 0 DC 12

*

RS 1 2 100

C1 2 3 1UF

R1 10 3 22K

R2 3 0 11K

Q1 4 3 5 Q2N2222

RC 10 4 1800

RE1 5 6 600

7/29/2019 Emitter Transistor Amplifier Vjezba

http://slidepdf.com/reader/full/emitter-transistor-amplifier-vjezba 4/4

RE2 6 0 600

CE 6 0 50UF

CL 4 7 10UF

RL 7 0 100K

*

.model Q2N2222 NPN(Is=3.108f Xti=3 Eg=1.11 Vaf=131.5 Bf=217.5 Ne=1.541

+ Ise=190.7f Ikf=1.296 Xtb=1.5 Br=6.18 Nc=2 Isc=0 Ikr=0 Rc=1

+ Cjc=14.57p Vjc=.75 Mjc=.3333 Fc=.5 Cje=26.08p Vje=.75

+ Mje=.3333 Tr=51.35n Tf=451p Itf=.1 Vtf=10 Xtf=2 Rb=10)

*

* ANALYSIS

.AC DEC 5 10 10MEG

.TRAN 0.001MS 0.2MS

* VIEW RESULTS

.PLOT AC V(2) V(5)

.PLOT TRAN V(2) V(5)

.PROBE

.END