EMIO-100TL-LVD01E LVDS to TTL Module...
-
Upload
dinhkhuong -
Category
Documents
-
view
265 -
download
5
Transcript of EMIO-100TL-LVD01E LVDS to TTL Module...
EMIO EMIO-100TL LVDS to TTL RGB module
Specifications subject to change without notice, contact your sales representatives for the most update information.
REV 0.2 Page 1 of 12 Feb. 6, 2014
EMIO-100TL-LVD01E LVDS to TTL Module
Datasheet
EMIO EMIO-100TL LVDS to TTL RGB module
Specifications subject to change without notice, contact your sales representatives for the most update information.
REV 0.2 Page 2 of 12 Feb. 6, 2014
CONTENTS 1. Overview ............................................................................................ 4
2. Electrical Features ............................................................................ 5
3. Environmental Features ................................................................... 5
4. Block Diagram ................................................................................... 6
5. Pin Assignment and Description ..................................................... 7 5.1 Connector Location ......................................................................................................... 7
5.2 LVDS connector, CN1 ..................................................................................................... 7
5.3 18/24-bit TTL RGB connector, CN2 ................................................................................. 8
5.4 VS and HS Jumper Setting connector, CN3 .................................................................... 9
6. Physical Dimension ........................................................................ 10
Appendix I: Part Number Table ......................................................... 11
Appendix II: Peripheral Cable recommendation .............................. 12
EMIO EMIO-100TL LVDS to TTL RGB module
Specifications subject to change without notice, contact your sales representatives for the most update information.
REV 0.2 Page 3 of 12 Feb. 6, 2014
Revision History
Rev. Date History
0.1 2014/2/5 1. 1st draft
0.2 2014/2/6 1. Added the Jumper information
Advantech reserves the right to make changes without further notice to any products or data herein to improve reliability, function, or
design. Information furnished by Advantech is believed to be accurate and reliable. However, Advantech does not assure any liability
arising out of the application or use of this information, nor the application or use of any product or circuit described herein, neither
does it convey any license under its patent rights nor the rights of others.
Copyright © 1983-2014 Advantech Co., Ltd. All rights reserved.
EMIO EMIO-100TL LVDS to TTL RGB module
Specifications subject to change without notice, contact your sales representatives for the most update information.
REV 0.2 Page 4 of 12 Feb. 6, 2014
1. Overview
Advantech EMIO-100TL, 18/24-bit LVDS to TTL RGB module, is a high-quality electronic
component developed and manufactured. The form factor of EMIO-100TL LVDS to TTL RGB
module is designed the full-size Mini PCIe solution.
The LVDS signals from the graphic controller are input to the LVDS to TTL RGB converter
module, EMIO-100TL. There the parallel RGB data is multiplexed and converted to a single
channel LVDS (Low Voltage Differential Signaling) interface in order to be connected to the TTL
panel. On the Display itself the received data is then demultiplexed, converted back to TTL
levels and sent to the inputs of the timing controller. The use of the LVDS interface allows the
data to travel at faster speeds across a narrow interface, addressing needs associated with
high bandwidth communication.
EMIO EMIO-100TL LVDS to TTL RGB module
Specifications subject to change without notice, contact your sales representatives for the most update information.
REV 0.2 Page 5 of 12 Feb. 6, 2014
2. Electrical Features
– Single chip LVDS to TTL RGB port with a variety of configurations.
– Support 1 Ch 18/24-bit LVDS to TTL RGB data outputs.
– 2 control outputs (Horizontal reverse scan, Vertical reverse scan)
3. Environmental Features
Temperature Ranges
– Operating : -10℃ ~ 70℃
– Storage : -40℃ ~ 85℃
Humidity
– 25% ~ 95%, 40℃
Random Vibration Test
– 5 - 500Hz, PSD 0.028G²/Hz,3.5Grms
– 3 axes, 1 hr/per axis
Acquired RoHS Certificate
Dimension:50.95 mm x 30 mm x 10 mm
Weight:30 g
EMIO EMIO-100TL LVDS to TTL RGB module
Specifications subject to change without notice, contact your sales representatives for the most update information.
REV 0.2 Page 6 of 12 Feb. 6, 2014
4. Block Diagram
Below Figure shows the operation of Advantech EMIO-100TL LVDS to TTL RGB module
from the system level, including the major hardware blocks.
EMIO EMIO-100TL LVDS to TTL RGB module
Specifications subject to change without notice, contact your sales representatives for the most update information.
REV 0.2 Page 7 of 12 Feb. 6, 2014
18/24-bit LVDS port
(CN1)
TTL RGB port
(CN2)
VS and HS Jumper Setting
(CN3)
5. Pin Assignment and Description
5.1 Connector Location
5.2 LVDS connector, CN1
The LVDS connector, CN1, is a Hirose DF13-20DP-1.25V 10x2-Pins connector
matching side is DF13-20DS-1.25V 10x2-Pins connector for LVDS singal input
connected with LVDS cable. The pins are numbered as shown in the table below.
CN1 Pin # Signal Name CN1 Pin # Signal Name
1 GND 2 GND
3 D0- 4 N/C
5 D0+ 6 N/C
7 D1- 8 N/C
9 D1+ 10 N/C
11 D2- 12 N/C
13 D2+ 14 N/C
15 CLK- 16 D3-
17 CLK+ 18 D3+
19 VCC 20 VCC
EMIO EMIO-100TL LVDS to TTL RGB module
Specifications subject to change without notice, contact your sales representatives for the most update information.
REV 0.2 Page 8 of 12 Feb. 6, 2014
5.3 18/24-bit TTL RGB connector, CN2
The 18/24-bit TTL RGB connector, CN2, is a Hirose DF13-40DP-1.25V 20x2-Pins
connector for TTL type LCD panel connected with TTL cable. The pins are numbered as
shown in the table below.
CN2 Pin # Signal Name CN2 Pin # Signal Name
1 VCC 2 VCC
3 GND 4 GND
5 VCC 6 VCC
7 N/C 8 GND
9 B0 10 B1
11 B2 12 B3
13 B4 14 B5
15 B6 16 B7
17 G0 18 G1
19 G2 20 G3
21 G4 22 G5
23 G6 24 G7
25 R0 26 R1
27 R2 28 R3
29 R4 30 R5
31 R6 32 R7
33 GND 34 GND
35 CLK 36 TTL_FP_VS
37 DE 38 TTL_FP_HS
39 N/C 40 N/C
EMIO EMIO-100TL LVDS to TTL RGB module
Specifications subject to change without notice, contact your sales representatives for the most update information.
REV 0.2 Page 9 of 12 Feb. 6, 2014
5.4 VS and HS Jumper Setting connector, CN3
The TTL_FP_VS and TTL_FP_HS Jumper Setting connector, CN3, is a 2.0mm
3x2-pins 180 degree, Male type pin header connector. The pins are numbered as shown
in the table below.
Cards can be configured by setting jumpers. A Jumper is a metal bridge used to
close an electric circuit. It consists of tw metal pins and a small metal clip (often protected
by a plastic cover) that slides over the pins to connect them. To close a jumper, you
connect the pins with the clip. To open a jumper, you remove the clip.
CN1
PH_3x2V_S2.00mm
246
135
TTL_FP_HSTTL_FP_VS
+3V3_LCD1 +3V3_LCD1
CN1(3-5)
MINIJUMPER_2_2.0mm
CN1(2-4)
MINIJUMPER_2_2.0mm
3-5
1-3
Low
High
Jumper settingTTL_FP_VS
Default
CN1(3-5)
High
4-6
2-4
Jumper setting
Low
TTL_FP_HS
Default
CN1(2-4)
Note:Default panel AUO G057VN01
EMIO EMIO-100TL LVDS to TTL RGB module
Specifications subject to change without notice, contact your sales representatives for the most update information.
REV 0.2 Page 10 of 12 Feb. 6, 2014
6. Physical Dimension
EMIO-100TL 18/24-bit LVDS to TTL RGB module (Unit: mm)
EMIO EMIO-100TL LVDS to TTL RGB module
Specifications subject to change without notice, contact your sales representatives for the most update information.
REV 0.2 Page 11 of 12 Feb. 6, 2014
Appendix I: Part Number Table
Product Description Advantech P/N
Advantech EMIO-100TL, 18/24-bit LVDS to TTL RGB module, 1-Ch, (-10~70°C) EMIO-100TL-LVD01E
EMIO EMIO-100TL LVDS to TTL RGB module
Specifications subject to change without notice, contact your sales representatives for the most update information.
REV 0.2 Page 12 of 12 Feb. 6, 2014
Appendix II: Peripheral Cable recommendation
1. LVDS, CN1, port cable Advantech P/N Description Picture
1700022577-01 Signal Cable, 2x10P-1.25 to 2x10P-1.25, L=30cm
(For EMIO-100TL to MIO-5250 usage)
1700022739-01 Signal Cable, 2x10P-1.25 to 2x10P-1.25, L=30cm
(For EMIO-100TL to SIMB-M02 usage)
2. TTL RGB, CN2, port cable Advantech P/N Description Picture
1700022578-01 Signal Cable, FPC-33P to 2x20P-1.25, L=30cm
(For EMIO-100TL to 96LEDK-A057VG70NX2 usage)
1700022579-01 Signal Cable, 1x5P-2.0 to 1x6P-1.0, L=30cm
(For EMIO-100TL to 96LEDK-A057VG70NX2 usage)