EMD 101 E1
-
Upload
chang-foo-koon -
Category
Documents
-
view
238 -
download
0
Transcript of EMD 101 E1
8/3/2019 EMD 101 E1
http://slidepdf.com/reader/full/emd-101-e1 1/17
EMD 101 Engineering Drawing
Exercise 1: SketchingGroup A4
Chang Foo Koon (111519) Group members: 1. Chor Hau Yik (113603)
2. Mohamad Norfazli bin Ismail (111541)
3. Mohamad Razif bin Mat Zain (111542)
4. Mohamad Safuan bin Noordin (111543)
School of Mechanical Engineering
Date of Submission 8 Nov 2011
Lecturer:
Dr Mohd Salman Abu Mansor
8/3/2019 EMD 101 E1
http://slidepdf.com/reader/full/emd-101-e1 2/17
Procedures for sketching the given profile:
SKETCH EXERCISE 1.1 ADJUSTING RING
1. Open a new sketch.
2. Select the front plane.
3. Select sketch from the toolbar.
4. Select the front plane and click sketch.
5. Click line and sketch the x-axis and the y-axis from the origin using centreline
and fix it.
6. Then click circle from the sketch toolbar, and draw a circle with radius 25mm and
fix it.
8/3/2019 EMD 101 E1
http://slidepdf.com/reader/full/emd-101-e1 3/17
7. Draw another circle with radius 38mm, tick on the circle
option and fix it.
8/3/2019 EMD 101 E1
http://slidepdf.com/reader/full/emd-101-e1 4/17
8. Then draw another circle with radius 58mm and fix it.
9. Then draw a line 30° from the positive x-axis and tick on
the line option and fix it.
8/3/2019 EMD 101 E1
http://slidepdf.com/reader/full/emd-101-e1 5/17
10. Select mirror entities from the sketch toolbar to reflect the line aboutthe y-axis.
8/3/2019 EMD 101 E1
http://slidepdf.com/reader/full/emd-101-e1 6/17
11. Click arc from the sketch toolbar and click on the centrepoint arc and
draw with contre on the intersection point between circle with radius 38mm and the line
on the the 3rd quadrant and fix it.
12. Then again use the mirror entities function to reflect the arc about the y-axis.
13. The reflect both arc about the x-axis.
8/3/2019 EMD 101 E1
http://slidepdf.com/reader/full/emd-101-e1 7/17
14. Then click arc from the sketch toolbar and click on the tangent arc . Thenmake the tangent arc to join the arc on the 2nd quadrant with the arc on 3rd quadrant and
repeat the same step for 1st and the 4th quadrant and fix it.
8/3/2019 EMD 101 E1
http://slidepdf.com/reader/full/emd-101-e1 8/17
15. Lastly complete all the dimension using smart dimention .
8/3/2019 EMD 101 E1
http://slidepdf.com/reader/full/emd-101-e1 9/17
16. Save your work.
SKETCH EXERCISE 1.3 GENEVA CAM
SKETCH EXERCISE 1.4 RATCHET WHEEL
SKETCH EXERCISE 1.5 ADJUSTABLE TABLE SUPPORT
SKETCH EXERCISE 1.7: GASKET
8/3/2019 EMD 101 E1
http://slidepdf.com/reader/full/emd-101-e1 10/17
1. Open SolidWorks 2010.
2. Select New from the File Menu.
3. Select Part as the New SolidWorks Document from the window.
4. Click Sketch, select the Front Plane. The selected Front Plane will rotates so it is parallel
to the screen.
8/3/2019 EMD 101 E1
http://slidepdf.com/reader/full/emd-101-e1 11/17
5. Sketch Horizontal and Vertical Centerline.
6. Click Circle from the sketch toolbar. Sketch a circle centered at the origin. Give diameter
of 3.10mm to the circle.
8/3/2019 EMD 101 E1
http://slidepdf.com/reader/full/emd-101-e1 12/17
7. Repeat the Step 6 with another two circles, the outest one is labelled as For Construction.
8. Sketch another two circles at the top with dimension stated respectively.
9. Click Trim Entities to delete part of the circles to produce the figure below.
8/3/2019 EMD 101 E1
http://slidepdf.com/reader/full/emd-101-e1 13/17
10. Use tangent arc to link the open end to the circle of diameter 4.5mm.
Hold the Cltrl key, and click the arc and the circle line, and set the relationship to tangent.
8/3/2019 EMD 101 E1
http://slidepdf.com/reader/full/emd-101-e1 14/17
11. Select tools-Sketch Tools, and then click Circular Pattern. Set the necessary particular to
duplicate the arc and circle.
12. Use Trim Entities again to clear the unwanted arcs, click in the Smart dimension
and insert necessary dimension and produce the final figure below.
8/3/2019 EMD 101 E1
http://slidepdf.com/reader/full/emd-101-e1 15/17
13. Save your work.
Complete sketches of the given profiles
SKETCH EXERCISE 1.1 ADJUSTING RING
8/3/2019 EMD 101 E1
http://slidepdf.com/reader/full/emd-101-e1 16/17
SKETCH EXERCISE 1.3 GENEVA CAM
8/3/2019 EMD 101 E1
http://slidepdf.com/reader/full/emd-101-e1 17/17
SKETCH EXERCISE 1.4 RATCHET WHEEL
SKETCH EXERCISE 1.5 ADJUSTABLE TABLE SUPPORT
SKETCH EXERCISE 1.7: GASKET