EMCal DCS Status By B. S. Nilsen, M. Cherney, J. Fujita Creighton University For the EMCal project.
-
Upload
adrien-matthey -
Category
Documents
-
view
215 -
download
2
Transcript of EMCal DCS Status By B. S. Nilsen, M. Cherney, J. Fujita Creighton University For the EMCal project.
EMCal DCS Status
By
B. S. Nilsen, M. Cherney, J. Fujita
Creighton UniversityFor the
EMCal project
Contents
• Problems to be solved
• Completed tasks
• Plans
Problems to be Solved• Introduction of Recipes
– Been having difficulties making a working implementation.
– Recent workshop been very helpful.– Want to have a backup dcs system before we try
implementing this again.– Needed to allow for multiple configurations like LED
running.
• Busy occurring during Physics run attempts– Not seen during stand alone runs– Effects ERP Drill and LHC Dry runs
• ERP Drill and LHC Dry run– Most recent attempt when well (ERP), but effected by
busy
Completed Tasks
• 4/12 Super-modules installed and working.
• Emergency Button implemented.
• L0 timing issue understood and patched.
Plans
• Continue to tack down Busy problems.
• Obtain and install Parallel PVSS system on new DCS machine.– Implement recipes.– Improve and streamline Control system.– Set up Cooling control and monitoring.– Implement LED calibration.
• Reestablish remote development and test bed.
The EndThat’s All Folks
QuickTime™ and a decompressor
are needed to see this picture.
Outline• Installation• Fee Cards• DCS machines• Recipes• Cooling• Emergency
Button• PVSS panels• Going Busy• Physics Drill
• High voltage– ISEG
OPC/CANHVcontrol
• Low voltage• Led calibration
system• L0 timing• Planning• LHC Dry Run
Installation
• 4 out of 12 Super modules installed and working.
L0 Latency
• L0 presently arriving 960ns after interaction (352 BC)
• Expect to improve by 6 or 7 BC (150-175 ns)
Emergency Button
• Installed in August
• Hardware version yet to come.
Fee cards
• Suspected noise fee card has been swapped (twice now) but noise still there.
• Problem must be else where.– LTU system.– ELMB system.– ?
Going Busy
• PVSS has Intermittently been going Busy, when trying to go global, OK when in standalone run.
• Is SOD checks in the physics runs?
• Still under investigation.
Recipes
• Been having difficulties making a working implementation.
• Recent workshop been very helpful.
• Want to have a backup dcs system before we try implementing this again.
• Needed to allow for multiple configurations like LED running
Cooling
• Still some hardware problems and developments under way.
• PVSS monitoring still under development.
DCS Machine
• Present machine limits being reached.
• Acquisition of additional machine just starting.
• CERN has new contract with HP and dcs machine parameters still under negotiations.
High voltage
• Intermittent Problems with Iseg HV system have been seen.
• Simultaneous running of Iseg OPC and IsegCANHVcontrol may be source of problem.
• Fix planned ASAP.
LHC Dry Run
• First Try: Failed due to problems with LHC clock switching
• 10/16/09 Was busy and not in today.
• 10/19/09
Central DCS has all Detectors In READY state All 4 LHCExperiments will perform 2*(READY-BEAMTUNING-READY)
Physics (ERP) Drill
• First attempt took 3 tries
• 10/15/09 Attempt EMCal failed.
• Most resent drill Performed OK
Cycle throughREADY BEAM-Tuning READY
LED System
• LED are now working
• Will require changes in PVSS for proper operations (recipes).
Low Voltage System
• Operational
PVSS Panels
• System to date is adequate
• Will need to be redesigned to better support of full EMCal.
• Will attempt to make operational efficiencies.
Planning• Iseg OPC CANHVcontrol conflict to be removed (go to all
OPC control).• Continue to tack down Busy problems.
• Obtain and install Parallel PVSS system on new DCS machine.– Implement recipes.– Improve and streamline Control system.– Set up Cooling control and monitoring.– Implement LED calibration.
• Reestablish remote development and test bed.