ELS Booklet

8/10/2019 ELS Booklet

http://slidepdf.com/reader/full/els-booklet 1/12

E L S

K

mergencyeak & eal

it

S Y .aving ou......



How to work

1. Always work safe

2 .

3. Aggresive chemicals

4 . You have to think about what could go wrong at the leaking S pot !! , and will beconsequences what could happen if no action is taken.

Then you must do whatever you can (in other words, whatever is ‘reasonably practicable’)to eliminate or minimise health and safety risks arising from the Leak which occurs

This process is known as risk management and involves several steps ;

secure area & warn other staff identify the Leak – find out what could cause harm assess & control risks if necessary – understand the nature of the harm that could becaused by the hazard, implement the most effective control measure that.review repair measures to ensure they are working as planned.



This kit provides a broad range of items that enable the quick repair of the most common leaks in pipes, tanks and drums. These sealingdevices and materials can repair pipe leaks and surface holes of allshapes, as well as cracks and gashes.

The kit complies with marine/ impa std. 812 368

General description

1 2 3 4

5 6 7 8

Ÿ

Ÿ

Ÿ

Ÿ

Ÿ

Ÿ

Ÿ

Ÿ

Ÿ

1. Hammer(rubber)/ Knife(1)2 . Wood Wedges (16 pieces)(2 )3. P iperepair(2 "3"4 ")(3)

4 . S peedsteel 2 ,2 g/ cm³(4 )5. F astplastik 1,6g/ cm³(5)6 . Filler rubber pack 50 x50 cm(6)7. Dripstop 2 5,38 ,50 mm(7)8 . S praycontrol 50 mm 10 m9. Spraystop 35 mm 10 m



ŸOil drum leakŸ

Unwanted sprayoutsŸLeaking pipesŸLeaking flangesŸDamaged containers

Where to use?

Above you can see how you can fix several leaks. By a leaking P ipe you can use

Dripstop, By a leaking flange you can use Spraycontrol/ S praystop, By a Leakingdrum use the filler rubber pack and the wooden stick.



Clean and roughen area to berepaired. Shut down pipes and hosesbefore repair. A vlean roughenedsurface results in a succesful repair

Pul a piece of theepoxystick, knead inyour hand so that the 2components mix

Place the material in thehole.

Wear gloves. open depackage at a time in order toescape from causingmoisture to cure the resin.|To activate the set, soak infresh or salt water for 3seconds

Application to damagedpipes: Apply PIPEREP byvery firmly wrapping thedamaged area extending 2inch (5.0cm) beyond repair

Continue toa apply pressure bijmolding PIPEREP tape in directionof wram until PIPEREP tape beginsto set. If needed, cut excessPIPEREP tape with knife orsciccors. tool can be vleanes withalcohol or acetone.

P iperepHow to use:



Clean surroundingequipment remove Oil&Grease

Wind softly around pipeenclose air between thelayers

wrinkles are okay....S plash will be going inthese spaces

F latten Tape aroundpipe or flangesmoothly

Almost finished result Cut a small hole in thelower part of the tape,liguid can drop outhere... leak wil bediscovered

S pray control

How to use:



S pray S top

Printed side

Printed sideSplashed exposed

side

Sheet cut end

TOP

BOTTOM

1 2 3 4 5

1Use a scissor to cut the tape in the right length before placing.

The length should be be a little longer than needed, leave thebacklayer unremoved. Clean the equipment where the tape needsto be installed.

2During the installing of the tape to pipes or equipment, graduallypeel the backside layer. Do not remove the backside layer

completely before installation because oil,spills, dust can causethan adhesion problems.

3If you have to install the tape at a place where there is nosmooth surface, there should be 2 or more windings around thepipe or equipment in order to protect against splashes.

4During installation of the tapes every following winding should

cover for ½ the former winding. You do not need extra force forthe application of the tape however a little pressure done byhand will not harm.

5Use a knife or scissors to remove S P RAYS TOP tape. Removedtape can Not be reused.

Anti-S plash Tape.



Before applying, roughen and clean area to be repaired. Wearimpereable gloves before handling or mixing uncured material.then follow these easy steps

1. Cut off requiredamount.

2 . Mix to uniform colorwith gloved fingers.

3. Apply to repair surfacewithin 2 minutes.

S peedS teel

1.Cut off requiredamount.

2 . Mix to uniformcolor with glovedfingers.

3.Apply to repairsurface within 10minutes.

F astP lastik



F iller Rubber pack

How to use:

2 .leaking hole in yourdrum

3. cover the holewith rubber pack.

4 . put the wooden stickon top of the rubbersheet.

5.smash it with thehammer.

6 .To keep the drumsteady on the ground usewooden wedges.

be aware that this is aemergency repair.

1.unwanted leak by collisionor other accident.



Where to use?

Above one can see a example how you need to work withS prayS top. F irst clean pipe/ flange and wrap tape aroundflange left and right side. This tape can only be used for

fuelpiping on vessels and is type approved.

Above one can see a example how you need to work withDripS top. Dripstop seals small gas or liquid leaks in piping.It can be used also for insulation and corrosionprotection.S tops air gas and powder.



Examples1. How to repair an leaking pipe with P iperepair kit.

Above one can see a example how you need to work withthe P iperepair set. F irst knead epoxy and adjust to thehole. Than soak piperepair in water and wind around pipe.Let tape cure

Left one can see a instruction how

you need to work with Speedseal orF astplastic. F irst knead mass andplace hard into leaking seal or weldsean. Than wait for 2 0 minutes forcuring piperepair in water and windaround pipe. Let tape cure



S Safety ervices T-ISS

ELS Booklet

Documents

Transcript of ELS Booklet