ELEVATION™ X 42 DIRECT VENT GAS FIREPLACE...FIREPLACE OPENING 37 1/8”* F.O. 44 3/4” OVERALL...
Transcript of ELEVATION™ X 42 DIRECT VENT GAS FIREPLACE...FIREPLACE OPENING 37 1/8”* F.O. 44 3/4” OVERALL...
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON L4M 0G8 Canada • 1(866)820-8686 • www.napoleon.com
42” *FIREPLACE OPENING
37 1/8”*F.O.
44 3/4”OVERALL
48”OVERALL 47 1/2”
HEADER
22 1/2” 22”
1”
8”
8” 5”
39 1/8”
RIGHT SIDE VIEWFRONT VIEWTOP VIEW
36 1/2”
Gas inlet
ELEVATION™ X 42 DIRECT VENT GAS FIREPLACE
W415-2777 / B / 03.13.20
Specifi cations
Model BTUWidth Height Depth
Glass SizeActual Framing Actual Framing Actual Framing
EX42NTEL 45,00044 3/4” 45 3/4” 48” 47 3/4” 22” 22 1/4” 31” x 38 1/4”
EX42PTEL 39,000
Dimensions
Appliance Location Combustible Mantel Clearances
MLK
J
TOP OFFIREPLACE OPENING
*
*
* Finishing flange (the finishing flange defines the perimeter of the fireplace opening. Framing or finishing materials must NEVER encroach inside the finishing flange).
Do not put objects in front of the appliance(minimum distance of 4 feet)*
SIDE WALL
6”
81 11/16”
57 13/16”
45 3/4”
22 1/4”
MANTEL DIMENSIONS
Ref Height Depth
J 15” 2”
K 17” 4”
L 19” 6”
M 21” 8”
Mantel clearances can be reduced with DHC™ kit (see DHC™ manual for installation instructions).
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON L4M 0G8 Canada • 1(866)820-8686 • www.napoleon.com
72”(183cm)
min.Recessed
volume must be added to
the overall size of the
enclosure.
ELEVATION™ X 42 DIRECT VENT GAS FIREPLACE
Product information provided is not complete and is subject to change without notice. Please consult the installation manual for the most up to date installation information.
W415-2777 / B / 03.13.20
Wall Penetration
Vent SectionsWhen passing through a wall, use fi restop spacer W010-1800 (supplied). When passing through a ceiling, use fi restop spacer W500-0028 (not supplied).
note:
Horizontal vent sections: A minimum clearance of 3” (76mm) on the top of the vent to combustibles and 2” (51mm) on the sides and bottom of the vent to combustibles is required. Vertical vent sections: A minimum clearance of 1” (25mm) all around the vent pipe on all vertical runs to combus-tibles is required.
Firestop assembly
Non-combustiblematerial
1" [25mm]
0” [0mm] if non-combustible finishing material is used such as brick and stone.
Insulated sleeve
3"[76mm] to top
2"[51mm] to
sides / bottom
Non-combustible
Brick
Combustible1" [25mm] minimum all sides for vertical venting sections.When passing through a ceiling, use firestop W500-0028 (not supplied).
4"min.
12"[305mm]* 72"
(182.8cm)min.
10 1/4"
63”plus rise
Framing
Flush Finish Framing Recessed Finish Framing
72”(183cm)
min.
45 3/4”
47 3/4”
45 3/4”
Max. 5 1/2”*
47 3/4”
* Recess frame can be “backed” with 3/4” ply to support TV mounting hardware.
* The minimum enclosure height is deter-mined based on volume of air needed in the enclosure.
22 1/4”6” min.
6” min.22 1/4”6” min.
6” min.
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON L4M 0G8 Canada • 1(866)820-8686 • www.napoleon.com
Do not put objects in front of the appliance(minimum distance of 4 feet)*
42”*OUVERTURE DE FOYER
37 1/8”*F.O.
44 3/4”COMPLET
48”COMPLET 47 1/2”
EN-TÊTE
22 1/2” 22”
1”
8”
8” 5”
39 1/8”
36 1/2”
Entrée de Gaz
W415-2777 / B / 03.13.20
Spécifi cations
Modèle BTULargeur Hauteur Profondeur
Taille de VerreRéel Ossature Réel Ossature Réel Ossature
EX42NTEL 45 00044 3/4” 45 3/4” 48” 47 3/4” 22” 22 1/4” 31” x 38 1/4”
EX42PTEL 39 000
Dimensions
Emplacement de l’Appareil
MUR DE CÔTÉ
Dégagements Combustible de la Tablette
MLK
J
TOP OFFIREPLACE OPENING
FOYER À GAZ VENTILÉ DIRECTE ÉLÉVATIONMD X 42
VUE DE FACE VUE DE CÔTÉ DROIT VUE DE DESSUS
ARRIVÉE DE GAZ
Ne placez pas de l’objets en avant de l’appareil (distance minimum de 4 pieds) *
*
* La bride de finition (la bride de finition définit le périmètre de l’ouverture de l’appareil. Les matériaux d’ossature ou de finition NE JAMAIS empiété à l’intérieur de la bride de finition).
DESSUS DEL’OUVERTURE DE L’APPAREIL
6”
81 11/16”
57 13/16”
45 3/4”
22 1/4”
DIMENSIONS DE LA TABLETTE
Réf Hauteur Profondeur
J 15” 2”
K 17” 4”
L 19” 6”
M 21” 8”
Les dégagements de la tablette peuvent être réduits avec le kit DHC™ (voir le manuel DHC™ pour les instructions d’installation).
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON L4M 0G8 Canada • 1(866)820-8686 • www.napoleon.com
Firestop assembly
Non-combustiblematerial
1" [25mm]
0” [0mm] if non-combustible finishing material is used such as brick and stone.
Insulated sleeve
3"[76mm] to top
2"[51mm] to
sides / bottom
Non-combustible
Brick
Combustible1" [25mm] minimum all sides for vertical venting sections.When passing through a ceiling, use firestop W500-0028 (not supplied).
4"min.
12"[305mm]* 72"
(182.8cm)min.
10 1/4"
W415-2777 / B / 03.13.20
Pénétration de Mur
63”plus la pente
FOYER À GAZ VENTILÉ DIRECTE ÉLÉVATIONMD X 42
L’information du produit fourni n’est pas complet et est sujet de changer sans préavis. Consultez le manuel d’installation pour information d’installation actuel.
Sections d’ÉventsLors du passage à travers un mur, utilisez l’espaceur coupe-feu W010-1800 (fourni). Lors du passage à travers un plafond, utilisez l’espaceur coupe-feu W500-0028 (non fourni).
note:
Sections d’évents horizontale: Un dégagement minimum aux matériaux combustibles de 3” (76mm) au-dessus et 2” (51mm) sur les côtés et au-des-sous est requis. Sections d’évents verticale: Un dégagement minimum aux matériaux combustibles de 1” (25mm) est requis toute autour du conduit d’évacuation sur toutes les courses verticale.
Ossature Fini - Affl euré et Encastré
Ossature Fini - Affl euré Ossature Fini - Encastré
72”(183cm)
min.
45 3/4”
47 3/4”
72”(183cm)
min.Recessed
volume must be added to
the overall size of the
enclosure.
45 3/4”
Max. 5 1/2”*
47 3/4”
* Le cadre encastré peut être « renforcé » avec une pièce contreplaqué d’un épaisseur de 3/4po pour supporter le matériel de montage du téléviseur.
* L’hauteur minimum de l’enceinte est déter-miné en fonction du volume d’air nécessaire dans l’enceinte.
22 1/4”6” min.
6” min.22 1/4”6” min.
6” min.