ELECTROCHEMICAL NH3-100S SENSOR (4 SERIES) (P/N...
2
Product Dimensions · Description · Environmental · Life Time · Intrinsic Safety Data · Physical Characteristics · Installation · · Product Data Sheet Maximum Overload: Sensitivity (20°C): Response Time (T90): Zero Signal (20°C): Nominal Range: Temperature Range: Max. S/C Current: Max. O/C Voltage: Max. Current at 200ppm NH3: REV.: 2016-01 Performance Characteristics · Note REV.: 2021/01 Page 1 0 ~ 100 ppm ≤ 45 s < ±0.4 μA < 2 ppm Pressure Range: Humidity Range: Long Time Output Drift: Recommended Storage Temp: Expected Operating Life: Storage Life: Warranty: 12 months 6 months in original packaging ABS 200 ppm Resolution: Baseline Shift (-40°C ~ 50°C): Linearity: Bias Voltage: Linear up to 100 ppm 15% ~ 90%RH non-condensing 2 years in clean air < 2% signal/month 1 ± 0.1 atm 0 mV 0.2 ppm -40°C ~ 50°C 10°C ~ 30°C Output signals from the sensor pins are different. Inappropriate use of the pins in product design will affect the sensor functionality. Exposure to high concentrations of solvent vapors should be avoided under any condition. Mechanical overstress may cause deformation or cracks of the plastic enclosure of the sensor. If the sensor is used in extreme environmental conditions, please contact us for more details. The performance data in this document are conducted by using SemeaTech recom- mended test circuitry and test environment at 20°C, 50%RH and 1 atm. Sensor perfor- mance varies under different environmental conditions. Please contact us if you need more details. All dimensions in mm All tolerances ±0.10mm unless otherwise stated 5 g None < 0.2 mA 1.3 V < 1.0 A 0.135 ± 0.035 μA/ppm Website: www.semeatech.com E-mail: [email protected] Weight (Nominal): Orientation: Housing Material: ELECTROCHEMICAL NH3-100S SENSOR (4 SERIES) (P/N: 059-1900-000) This sensor is designed for the measurement of NH3 concentration in gas phase. It can be used as the pin-to-pin replacement of the stand- ard 4-series electrochemical NH3 sensors which made by the other manufacturers. 16.0 20.0 13.5 18.0 Working Reference Counter 15.8 16.6 1.5 4.4
Transcript of ELECTROCHEMICAL NH3-100S SENSOR (4 SERIES) (P/N...
Product Dimensions· Description
·
Environmental·
Life Time·
Intrinsic Safety Data·
Physical Characteristics·
Installation··
Product Data Sheet
Maximum Overload:Sensitivity (20°C): Response Time (T90): Zero Signal (20°C):
Nominal Range:
Temperature Range:
Max. S/C Current: Max. O/C Voltage: Max. Current at 200ppm NH3:
REV.: 2016-01
Performance Characteristics
·
Note
REV.: 2021/01Page 1
0 ~ 100 ppm
≤ 45 s< ±0.4 μA
< 2 ppm
Pressure Range:Humidity Range:
Long Time Output Drift:Recommended Storage Temp:Expected Operating Life:Storage Life:Warranty: 12 months
6 months in original packaging
ABS
200 ppm
Resolution:Baseline Shift (-40°C ~ 50°C):
Linearity:Bias Voltage:
Linear up to 100 ppm
15% ~ 90%RH non-condensing
2 years in clean air
< 2% signal/month
1 ± 0.1 atm
0 mV
0.2 ppm
-40°C ~ 50°C
10°C ~ 30°C
Output signals from the sensor pins are different. Inappropriate use of the pins in product design will affect the sensor functionality. Exposure to high concentrations of solvent vapors should be avoided under any condition. Mechanical overstress may cause deformation or cracks of the plastic enclosure of the sensor. If the sensor is used in extreme environmental conditions, please contact us for more details.
The performance data in this document are conducted by using SemeaTech recom-mended test circuitry and test environment at 20°C, 50%RH and 1 atm. Sensor perfor-mance varies under different environmental conditions. Please contact us if you need more details.
All dimensions in mmAll tolerances ±0.10mm unless otherwise stated
5 gNone
< 0.2 mA1.3 V
< 1.0 A
0.135 ± 0.035 μA/ppm
Website: www.semeatech.comE-ma i l : [email protected]
Weight (Nominal): Orientation:
Housing Material:
ELECTROCHEMICAL NH3-100S SENSOR (4 SERIES) (P/N: 059-1900-000)
This sensor is designed for the measurement of NH3 concentration in gas phase. It can be used as the pin-to-pin replacement of the stand- ard 4-series electrochemical NH3 sensors which made by the other manufacturers.
16.020.0
13.5
18.0
Working
Reference
Counter
15.8
16.6
1.5
4.4
· Cross-Sensitivity Data
·
·
Safety Note
Gas Concentration (ppm)
REV.: 2021/01Page 2
Product Data Sheet
Output Signal (ppm NH3 equivalent)
Note: The cross sensitivities include but not limited to the above gases. It may also respond to other gases. The data in the table above may vary from different batches of sensors and the changes of test environment. Calibration using the gases that have the cross sensitivities to this sensor is not recommended.
Temperature Data
Website: www.semeatech.comE-ma i l : [email protected]
Hydrogen Sulfide
HydrogenIsobutyleneEthanol
255,000
1001,000
100200
Carbon MonoxideCarbon Dioxide
22.0 0.00.00.00.0
< 1.0
5040302010-10-20-30-400
20
40
60
80
120
100
Temperature Performance of SemeaTech 4NH3-100S Sensor
% O
utpu
t (re
fere
nced
to 2
0°C
)
Temperature (°C)
Average
+95% confidence
- 95% confidence
0
盛密科技SemeaTech
盛密科技SemeaTech
盛密科技SemeaTech
盛密科技SemeaTech
盛密科技SemeaTech
盛密科技SemeaTech
盛密科技SemeaTech
盛密科技SemeaTech
盛密科技SemeaTech
ELECTROCHEMICAL NH3-100S SENSOR (4 SERIES) (P/N: 059-1900-000)
This product data sheet is used for reference only.
This sensor is designed to be used in certain instruments for life critical applications. To ensure the sensor functions per its specifications inside the instrument, it is required to read the instrument user’s guide carefully and comply with the cali- bration procedures by using certified target calibration gas before each use. Failure to do so may cause serious injury and fatality. Please do not open the sensor plastic enclosure because the electrolyte and other chemicals stored inside are harmful. It is highly recommended for customers to validate the sensor performance using this document as a reference for their product designs or applications.
SemeaTech is committed to providing its customers the most accurate data based on its best knowledge. SemeaTech does not provide a product warranty for failures of using its products in accordance with product specifications that are described in the datasheet, or other misuses, abuse, negligence to the product.
![AHLCON PUBLIC SCHOOL - 12.doc · Web view... (III) chloride. 2) potassium tetrahydrozincate(II) 3) ... [CO (NH3)3Cl2] , [CO(NH3)5Cl]Cl2 , [CO(NH3)6]Cl3 , [CO(NH3)4Cl2]Cl. 19. Name](https://static.fdocuments.us/doc/165x107/5a9e9e6e7f8b9a0d158b9d3f/docahlcon-public-12docweb-view-iii-chloride-2-potassium-tetrahydrozincateii.jpg)