Electric designer
2
® CADISON Electric-Designer ® The CADISON Electric-Designer combines planning efforts with process control engineering. PLT points (measuring points) defined by the process engineer are further detailed ® by CADISON Electric-Designer with the required instrumentation. The electrical planning engineers base their work on the specified media data and connection parameters delivered by the process engineer. Key Features ? Integrated and Intelligent database Electrical 2D schematic, 3D model system. ? Automatic creation of Terminal Drawings and contact sets (automatic adjustment of pin numbers, etc). ? Numbering and identification system according to DIN and KKS. Automatic Device Tagging and Wire numbering. ? Configurable Logic Analyzer for error checking. ? Real-time coil and contacts cross-referencing. ? Automatic connection of wiring between components. ? Customizable object designation (Text Mask). ? Auto generation of Legend, Notes and Abbreviation. ? Easy and quick cross referencing of components represented in different drawings. (Devices with distributed representation - Relay contacts, Terminals etc). ? Automatic and customizable reports generation. ? Project revision management for reports and drawings. ? ETAP interface for SLD’s which reduces the need for manual entries by 50%. 3D cable tray and bus duct routing & 3D Panel layout drawings ? Availability of 3D E&I Equipments, Meters, Panels, Ducts enable creation of Layouts linked with 3D Model, clash detection. ? Automatic Cable Routing, Extendable Cable tray library to handle complex routing. Facility Management Electric-Designer is used both for electrical planning of a plant in classical plant engineering and even for facility management. For example, this module is used for document creation for operation management of complex line networks. Typical Pre-fabricated typicals are used for automatic graphic generation and presentation of instrumentation in the measuring-point chart. The planning engineer may use pre- fabricated ‘Typical’. It is easy to extend the ‘Typical’ to suit project need. Loop Wiring Diagrams ? Predefined measuring point structure in form of ‘Typical’. ? Reference / Assign ‘Typical’ to a measuring point. ? Easy creation and updating of Measuring Point ‘Typical’. ? Drag and Drop to create automatic loop wiring diagram. Devices with distributed representation (relay-contact set) ? Runtime calculation of free and used contacts. ? Intelligent and easy selection functionality while inserting contact in drawing. ? Auxiliary contact blocks for augmenting capacity of relay / contactor. Automatic Legend Creation ? Possibility to choose the property to be displayed along with symbol. ? Facility to filter or limit type of objects to be displayed in legend with help of configuration file. ® CADISON Electric-Designer (Integrated Designer Module) 3D Installation Layout Circuit Diagram
description
Preparation of planning documents for instrumentation, power plants and control but also installation and process measuring and control technology are in the competence of the electric design engineer. The common data base permits at any time the access to information about all trades involved in the project such that planning of electrical engineering can be combined with planning of process engineering.
Transcript of Electric designer
®CADISON Electric-Designer
®The CADISON Electric-Designer combines planning efforts
with process control engineering. PLT points (measuring
points) defined by the process engineer are further detailed ®by CADISON Electric-Designer with the required
instrumentation. The electrical planning engineers base their
work on the specified media data and connection parameters
delivered by the process engineer.
Key Features
?Integrated and Intelligent database Electrical 2D
schematic, 3D model system.
?Automatic creation of Terminal Drawings and contact sets
(automatic adjustment of pin numbers, etc).
?Numbering and identification system according to DIN
and KKS. Automatic Device Tagging and Wire numbering.
?Configurable Logic Analyzer for error checking.
?Real-time coil and contacts cross-referencing.
?Automatic connection of wiring between components.
?Customizable object designation (Text Mask).
?Auto generation of Legend, Notes and Abbreviation.
?Easy and quick cross referencing of components
represented in different drawings. (Devices with
distributed representation - Relay contacts, Terminals etc).
?Automatic and customizable reports generation.
?Project revision management for reports and drawings.
?ETAP interface for SLD’s which reduces the need for
manual entries by 50%.
3D cable tray and bus duct routing & 3D Panel layout
drawings
?Availability of 3D E&I Equipments, Meters, Panels, Ducts
enable creation of Layouts linked with 3D Model, clash
detection.
?Automatic Cable Routing, Extendable Cable tray library to
handle complex routing.
Facility Management
Electric-Designer is used both for electrical planning of a
plant in classical plant engineering and even for facility
management. For example, this module is used for document
creation for operation management of complex line
networks.
Typical
Pre-fabricated typicals are used for automatic graphic
generation and presentation of instrumentation in the
measuring-point chart. The planning engineer may use pre-
fabricated ‘Typical’. It is easy to extend the ‘Typical’ to suit
project need.
Loop Wiring Diagrams
?Predefined measuring point structure in form of ‘Typical’.
?Reference / Assign ‘Typical’ to a measuring point.
?Easy creation and updating of Measuring Point ‘Typical’.
?Drag and Drop to create automatic loop wiring diagram.
Devices with distributed representation (relay-contact
set)
?Runtime calculation of free and used contacts.
?Intelligent and easy selection functionality while inserting
contact in drawing.
?Auxiliary contact blocks for augmenting capacity of relay /
contactor.
Automatic Legend Creation
?Possibility to choose the property to be displayed along
with symbol.
?Facility to filter or limit type of objects to be displayed in
legend with help of configuration file.
®CADISON Electric-Designer(Integrated Designer Module)
3D Installation LayoutCircuit Diagram
Automatic Device Tagging and Wire Numbering
?Multiple possibilities for auto numbering of wires and
devices.
?Dynamic number assignment at the time of creation.
?Renumbering will reassign the number based on level of
selection, position of devices with in drawing. Provision for
renumbering at drawing, logical plant, location and project
levels.
Automatic Terminal Drawing
?Automatic terminal drawing feature to create new
Terminal Drawing.
?Drag and drop feature to create multiple terminal
diagrams in a single sheet.
?Terminal strip editor- to rearrange terminals, re-
numbering of terminals in GUI.
?Configure graphical representation parameters at project
level.
?Context sensitive menu for creation as well as updating of
existing drawing.
PLC Configurator
?Supports the work of electric planning engineer for
management of input and output signals.
?Process flow can be presented in one function diagram
with all signals.
2D GA and Hookup Drawings
?Extraction of 2D layout drawings from 3D model.
?Tabulated list with predefined ‘Typical’ (image) for design
process clarity.
?Provision to create ‘Typical’ mounting details suit to project
needs.
?Automatic creation of hookup drawing for instrument
installation too.
?Configurable drawing templates, ‘Typical’ and hookup
parameters.
?Assign / link multiple process measuring points to a single
hookup.
ETAP Interface
To export Single Line Diagrams to ETAP though data
exchange excel format.
Report Generator
?Ability to generate reports at Project, Drawing and Object
level.
?Configurable reports for list of Input / Output electrical
and automation components.
?Considerable numbers of predefined report formats are
available with standard installer.
?Supports MS Word, Excel & PDF, generate multilingual
reports (English, German).
Terminal Strip Editor
2D GA of Cabinet / Panels
www.cadison.com
Single Line Diagram
Customizable Symbols and Catalogs
