(Electric) (10000000-- ) Walk--Behind Scrubber Operator Manual 5700XP User Manual.pdf · 5700XP...

5700XP

*331533*www.tennantco.com

Walk--Behind ScrubberOperator Manual

331533Rev. 02 (10-2008)

North America / International

ES Extended Scrub SystemR

(Electric)

(10000000-- )

The Safe Scrubbing Alternativer

http://www.floorequipmentparts.com

This manual is furnished with each new model. It provides necessary operation and maintenance instructions.

Read this manual completely and understand the machine before operating or servicing it.

This machine will provide excellent service. However, the best results will be obtained at minimum costs if:

S The machine is operated with reasonable care.

S The machine is maintained regularly - per the machine maintenance instructions provided.

S The machine is maintained with manufacturer supplied or equivalent parts.

PROTECT THE ENVIRONMENTPlease dispose of packaging materials,old machine components such asbatteries, hazardous fluids, includingantifreeze and oil, in an environmentallysafe way according to local wastedisposal regulations.

Always remember to recycle.

MACHINE DATAPlease fill out at time of installation for future reference.

Model No. --

Serial No. --

Machine Options --

Sales Rep. --

Sales Rep. phone no. --

Customer Number --

Installation Date --

Tennant CompanyPO Box 1452Minneapolis, MN 55440Phone: (800) 553--8033 or (763) 513--2850www.tennantco.com

FaST--PAK is a US registered and unregistered trademark of Tennant Company.

Specifications and parts are subject to change without notice.

Copyright E 2006, 2008 TENNANT, Printed in U.S.A.

CONTENTS

15700xp 331533 (10--08)

CONTENTS

Page

SAFETY PRECAUTIONS 3. . . . . . . . . . . . . . . . .

OPERATION 5. . . . . . . . . . . . . . . . . . . . . . . . . . . .OPERATOR RESPONSIBILITY 5. . . . . . . .MACHINE COMPONENTS 6. . . . . . . . . . . .CONTROL PANEL SYMBOLS 7. . . . . . . . .CONTROLS AND INSTRUMENTS 8. . . . . .STEERING HANDLES 9. . . . . . . . . . . . . . . .

SOLUTION FLOW LEVER 10. . . . . . . . .POWER WANDSWITCH (OPTION) 10. . . . . . . . . . . . . .

SPEED SWITCH AND INDICATOR 11. . . . .SQUEEGEE SWITCH 11. . . . . . . . . . . . .BRUSH PRESSURE SWITCHAND INDICATOR 11. . . . . . . . . . . . . . . .

FaST SWITCH (OPTION) 12. . . . . . . . . . . . .ec--H2O SWITCH (OPTION) 12. . . . . . . . . . .

ES SWITCH (OPTION) 13. . . . . . . . . . . .RECOVERY TANKFULL INDICATOR 13. . . . . . . . . . . . . . .

SCRUBBING SWITCH 14. . . . . . . . . . . . . . . .BATTERY DISCHARGEINDICATOR 14. . . . . . . . . . . . . . . . . . . . .HOURMETER 14. . . . . . . . . . . . . . . . . . . .

ON-OFF KEY SWITCH 15. . . . . . . . . . . . . . . .SQUEEGEE LEVER 15. . . . . . . . . . . . . . .POWER KILL SWITCH (OPTION) 15. . .

CIRCUIT BREAKERS 16. . . . . . . . . . . . . . . . .FUSES (OPTION) 17. . . . . . . . . . . . . . . . . . . .

SOLUTION TANK HOSE 17. . . . . . . . . . .RECOVERY TANK DRAIN HOSE 18. . . . . . .

SUPPORT ARM 18. . . . . . . . . . . . . . . . . .STOP ARM 18. . . . . . . . . . . . . . . . . . . . . .

SQUEEGEE DOWNPRESSURE CAMS 19. . . . . . . . . . . . . . . . . .

SQUEEGEE LEVELING KNOB 19. . . . .PARKING BRAKE (OPTION) 19. . . . . . .

HOW THE MACHINE WORKS 20. . . . . . . . .FaST SCRUBBINGSYSTEM (OPTION) 21. . . . . . . . . . . . . .ec--H2O SYSTEM (OPTION) 22. . . . . . .

PRE-OPERATION CHECKLIST 23. . . . . . . .INSTALLING FaST PAKAGENT (OPTION) 24. . . . . . . . . . . . . . . . . . .STARTING THE MACHINE 26. . . . . . . . . . . .

PageFILLING THE TANKS 26. . . . . . . . . . . . . . . . .NORMAL SCRUBBING 29. . . . . . . . . . . . . . .DOUBLE SCRUBBING 33. . . . . . . . . . . . . . . .STOP SCRUBBING 34. . . . . . . . . . . . . . . . . . .DRAINING AND CLEANINGTHE TANKS 35. . . . . . . . . . . . . . . . . . . . . . . .STOP THE MACHINE 40. . . . . . . . . . . . . . . . .OPERATION ON INCLINES 40. . . . . . . . . . .POST-OPERATION CHECKLIST 41. . . . . . .MACHINE TROUBLESHOOTING 42. . . . . . .OPTIONS 44. . . . . . . . . . . . . . . . . . . . . . . . . . .

VACUUM WAND 44. . . . . . . . . . . . . . . . . .POWER WAND 48. . . . . . . . . . . . . . . . . . .

MAINTENANCE 53. . . . . . . . . . . . . . . . . . . . . . .MAINTENANCE CHART 53. . . . . . . . . . . . . . .LUBRICATION 55. . . . . . . . . . . . . . . . . . . . . . .

REAR CASTERS 55. . . . . . . . . . . . . . . . .TRANSAXLE 55. . . . . . . . . . . . . . . . . . . . .

BATTERIES 55. . . . . . . . . . . . . . . . . . . . . . . . .CHARGING THE BATTERIES 57. . . . . .

TOUCH PANEL 59. . . . . . . . . . . . . . . . . . . . . .ELECTRIC MOTORS 60. . . . . . . . . . . . . . . . .SCRUB HEAD 61. . . . . . . . . . . . . . . . . . . . . . .

DISK BRUSH SCRUBHEAD SKIRT 61. . . . . . . . . . . . . . . . . . . .ADJUSTING THE SCRUBHEAD SKIRT 61. . . . . . . . . . . . . . . . . . . .REPLACING THE SCRUBHEAD SKIRT 62. . . . . . . . . . . . . . . . . . . .CYLINDRICAL BRUSH SCRUBHEAD SKIRTS 63. . . . . . . . . . . . . . . . . .ADJUSTING THE SCRUBHEAD SKIRTS 63. . . . . . . . . . . . . . . . . .REPLACING THE SCRUBHEAD SKIRTS 63. . . . . . . . . . . . . . . . . .REMOVING OR REPLACING THESCRUB HEAD 64. . . . . . . . . . . . . . . . . . .SCRUB HEAD/CIRCUITBREAKERS 64. . . . . . . . . . . . . . . . . . . . .LEVELING THE SCRUB HEAD 66. . . . .

SCRUB BRUSHES 68. . . . . . . . . . . . . . . . . . .DISK BRUSHES 68. . . . . . . . . . . . . . . . . .REPLACING THE DISK BRUSHES 68.CYLINDRICAL BRUSHES 70. . . . . . . . . .REPLACING THECYLINDRICAL BRUSHES 70. . . . . . . .CHECKING AND ADJUSTINGCYLINDRICAL BRUSH PATTERN 71.

CONTENTS

5700xp 331533 (10--08)2

PageSOLUTION SYSTEM 73. . . . . . . . . . . . . . . . .

RECOVERY TANK 73. . . . . . . . . . . . . . . .SOLUTION TANK 74. . . . . . . . . . . . . . . . .

FaST SYSTEM (OPTION) 75. . . . . . . . . . . . .FaST SYSTEM MAINTENANCE 75. . . .FaST SYSTEM FILTER SCREEN 76. . .FaST SUPPLY HOSECONNECTOR 76. . . . . . . . . . . . . . . . . . .

ec--H2O SYSTEM (OPTION) 77. . . . . . . . . . .ec--H2O MODULE FLUSHPROCEDURE 77. . . . . . . . . . . . . . . . . . .

SQUEEGEE 78. . . . . . . . . . . . . . . . . . . . . . . . .REMOVING THESQUEEGEE ASSEMBLY 78. . . . . . . . .INSTALLING THESQUEEGEE ASSEMBLY 79. . . . . . . . .LEVELING THE SQUEEGEE 79. . . . . . .ADJUSTING SQUEEGEEBLADE DEFLECTION 80. . . . . . . . . . . .ADJUSTING THE SQUEEGEEGUIDE ROLLERS 81. . . . . . . . . . . . . . . .

SQUEEGEE BLADES 81. . . . . . . . . . . . . . . . .REPLACING OR ROTATINGTHE REAR SQUEEGEE BLADE 81. . .REPLACING OR ROTATING THEFRONT SQUEEGEE BLADE 82. . . . . .

PageBELTS AND CHAINS 84. . . . . . . . . . . . . . . . .

BRUSH DRIVE BELT 84. . . . . . . . . . . . . .STATIC DRAG CHAIN 84. . . . . . . . . . . . .

TIRES 85. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PUSHING AND TRANSPORTINGTHE MACHINE 85. . . . . . . . . . . . . . . . . . . . . .

PUSHING THE MACHINE 85. . . . . . . . .TRANSPORTING THE MACHINE 86. . .

MACHINE JACKING 88. . . . . . . . . . . . . . . . . .STORAGE INFORMATION 88. . . . . . . . . . . .

FREEZE PROTECTION 88. . . . . . . . . . .

SPECIFICATIONS 90. . . . . . . . . . . . . . . . . . . . . . .GENERAL MACHINEDIMENSIONS/CAPACITIES 90. . . . . . . . . . .FaST SYSTEM (OPTION) 91. . . . . . . . . . . . .ec--H2O SYSTEM (OPTION) 91. . . . . . . . . . .GENERAL MACHINEPERFORMANCE 91. . . . . . . . . . . . . . . . . . . .POWER TYPE 92. . . . . . . . . . . . . . . . . . . . . . .TIRES 92. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .MACHINE DIMENSIONS 93. . . . . . . . . . . . . .

SAFETY PRECAUTIONS

35700XP 331533 (10--08)

SAFETY PRECAUTIONS

The following symbols are used throughout thismanual as indicated in their description:

WARNING: To warn of hazards orunsafe practices that could result insevere personal injury or death.

FOR SAFETY: To identify actions thatmust be followed for safe operation ofequipment.

This machine is designed solely for scrubbing dirtand dust in an indoor environment. Tennant doesnot recommend using this machine in any otherenvironment.

The following information signals potentiallydangerous conditions to the operator orequipment. Read this manual carefully. Knowwhen these conditions can exist. Locate all safetydevices on the machine. Then, take necessarysteps to train machine operating personnel.Report machine damage or faulty operationimmediately. Do not use the machine if it is not inproper operating condition.

WARNING: Batteries emit hydrogen gas.Explosion or fire can result. Keepsparks and open flame away. Keepcovers open when charging.

WARNING: Flammable materials cancause an explosion or fire. Do not useflammable materials in tank(s).

WARNING: Flammable materials orreactive metals can cause an explosionor fire. Do not pickup.

FOR SAFETY:

1. Do not operate machine:-- Unless trained and authorized.-- Unless operation manual is read andunderstood.

-- In flammable or explosive areas unlessdesigned for use in those areas.

2. Before starting machine:-- Make sure all safety devices are inplace and operate properly.

-- Check brakes and steering for properoperation (if so equipped).

3. When using machine:-- Go slow on inclines and slipperysurfaces.

-- Use care when backing machine.-- Follow mixing and handlinginstructions on chemical containers.

4. Before leaving or servicing machine:-- Stop on level surface.-- Set parking brake (if equipped).-- Turn off machine and remove key.

5. When servicing machine:-- Avoid moving parts. Do not wear loosejackets, shirts, or sleeves whenworking on machine.

-- Block machine tires before jackingmachine up.

-- Jack machine up at designatedlocations only. Block machine up withjack stands.

-- Use hoist or jack that will support theweight of the machine.

-- Wear eye and ear protection whenusing pressurized air or water.

-- Disconnect battery connections beforeworking on machine.

-- Wear protective gloves and eyeprotection when handling vinegar.

-- Avoid contact with battery acid.-- Use Tennant supplied or equivalentreplacement parts.

6. When loading/unloading machineonto/off truck or trailer:-- Turn off machine.-- Use truck or trailer that will supportthe weight of the machine.

-- Use winch. Do not push the machineonto/off the truck or trailer unless theload height is 380 mm (15 in) or lessfrom the ground.

-- Set parking brake after machine isloaded (option).

-- Block machine tires.-- Tie machine down to truck or trailer.

SAFETY PRECAUTIONS

5700XP 331533 (9--06)4

The safety labels appear on the machine in thelocations indicated. If these or any label becomesdamaged or illegible, install a new label in itsplace.

BATTERY CHARGING LABEL -- LOCATED ONTHE UNDERSIDE OF THE SOLUTION TANK.

FLAMMABLE SPILLS LABEL -- LOCATED ONTHE OPERATOR CONSOLE.

FOR SAFETY LABEL -- LOCATED ON THEOPERATOR CONSOLE.

FLAMMABLE MATERIALS LABEL -- LOCATEDON THE UNDERSIDE OF THE SOLUTIONTANK COVER.

10066

OPERATION

55700XP 331533 (9--06)

OPERATION

OPERATOR RESPONSIBILITY

- The operator’s responsibility is to take careof the daily maintenance and checkups ofthe machine to keep it in good workingcondition. The operator must inform theservice mechanic or supervisor when themaintenance intervals are required as statedin the MAINTENANCE section of thismanual.

- Read this manual carefully before operatingthis machine.

FOR SAFETY: Do not operate machine,unless operation manual is read andunderstood.

- Check the machine for shipping damage.Check to make sure the machine iscomplete per shipping instructions.

- Keep your machine regularly maintained byfollowing the maintenance information in thismanual. We recommend taking advantageof a regularly scheduled service contractfrom your Tennant representative.

- Order parts and supplies directly from yourauthorized Tennant representative. Use theparts manual provided when ordering parts.

- After operation, follow the recommendeddaily and hourly procedures stated in theMAINTENANCE CHART.

07324

OPERATION

5700XP 331533 (10--08)6

MACHINE COMPONENTS

AD

E

F

G

H

I

J

K

L

MC

O

N

A

B

C

L

O

P

Q

R1034410343

A. Solution tankB. Solution tank fill openingC. Recovery tankD. Console panelE. SqueegeeF. Squeegee leverG. Squeegee down pressure camsH. Squeegee leveling knobI. Parking brake (option)J. Recovery tank drain hoseK. Solution tank hoseL. Support armM. Stop armN. BatteriesO. Scrub headP. Scrub brush access coverQ. Scrub brush idler doorR. FaST solution system (option)

ec-H2O System Module (option)

OPERATION

75700XP 331533 (9--06)

CONTROL PANEL SYMBOLS

These symbols identify controls and displays onthe machine:

Solution flow Key switch

Battery charge Variable flow or rate

Power wand or vacuum wand Circuit breaker #1

Travel speed Circuit breaker #2

Squeegee Circuit breaker #3

Brush pressure Circuit breaker #4

ES (Extended scrub) Circuit breaker #5

Recovery tank full Circuit breaker #6

Scrubbing

OPERATION

5700XP 331533 (10--08)8

CONTROLS AND INSTRUMENTS

CB1

CB2

CB3

CB4

CB5

CB6

B

E F G

H IJ

K

M

N

A

O

A

L

PQ

C

O

R

D

S

10346

A. Steering handlesB. Solution flow leverC. Battery discharge indicatorD. FaST switch (option) or ec-H2O switch (option) or

Power wand switch (option)E. Speed switch and indicatorF. Squeegee switchG. Brush pressure switch and indicatorH. ES switch (option)I. Recovery tank full indicatorJ. Scrubbing switchK. HourmeterL. On-off key switchM. Power kill switch (option)N. Steering height adjustment latchO. Circuit breakersP. Solution tank hoseQ. Recovery tank drain hoseR. Squeegee leverS. ec-H2O system indicator light (option)

OPERATION

95700XP 331533 (9--06)

STEERING HANDLES

The steering handles control the machine speedand direction.

Forward: Rotate the handles forward. The furtherforward you rotate the handles, the faster themachine will go.

Backward: Rotate the handles toward you.

Turning: Push the machine in the direction of theturn with the steering handles. The machine willturn on the swivel casters.

Stopping: Release the handles.

OPERATION

5700XP 331533 (10--08)10

The steering handles and console height isadjustable.

Adjust: Pull up on the height adjustment latch,move the console up or down to the desiredheight. Then push down the latch to lock theconsole in position.

SOLUTION FLOW LEVER

The solution flow lever controls the amount ofsolution flow to the floor.

Increase: Push the lever forward.

Decrease: Pull the lever backward.

NOTE: A solenoid valve dispenses the solution tothe scrub head. The valve opens when thesteering handles are rotated forward, and closeswhen the steering handles are released in neutralposition.

NOTE: When using the FaST or ec--H2O system(option), the solution flow lever is nonfunctional.The FaST and ec--H2O system flow rates arepre--set. The ec--H2O module has optional flowrate settings. If solution flow adjustments arerequired, contact an Authorized Service Center.

POWER WAND SWITCH (OPTION)

The power wand switch turns on and off thepower wand solution system.

On: Press the top of the switch. The switch willlight up.

Off: Press the bottom of the switch.

OPERATION

115700XP 331533 (9--06)

SPEED SWITCH AND INDICATOR

The speed switch allows variable maximumforward speed of the machine.

Change speed: Press the switch. Each time youpress the switch, the speed will increase until itreaches the maximum setting, then the speed willreturn to the minimum setting.

SQUEEGEE SWITCH

The squeegee switch controls the squeegeeposition and vacuum fan.

Lower squeegee and start vacuum fan: Press theswitch.

Raise squeegee and stop vacuum fan: Press theswitch.

NOTE: The squeegee will not lower if it is lockedin the up position with the squeegee lever.

BRUSH PRESSURE SWITCH AND INDICATOR

The brush pressure switch adjusts the amount ofbrush pressure to the floor. The brush pressureindicator shows the pressure selection.

The brush pressure switch has four positions.Under normal conditions, the brush pressureshould be set in the minimum settings. Underheavy grime conditions, the brush pressureshould be set in the maximum settings. Travelspeed and floor conditions will affect thescrubbing performance.

Change brush pressure: Press the switch. Eachtime you press the switch, the brush pressure willincrease until it reaches the maximum setting.Then the pressure will return to the minimumsetting.

NOTE: When the machine is powered off, thebrush pressure will remain in the last setting used.

OPERATION

5700XP 331533 (10--08)12

FaST SWITCH (OPTION)

The FaST switch (option) enables the FaST(Foam Scrubbing Technology) system. When theFaST system is enabled, it is turned on and offwith the scrub switch

Enable the FaST system: Press the top of theFaST switch.

Enable conventional scrubbing: Press the bottomof the FaST switch.

NOTE: Disable the FaST system before using themachine for conventional scrubbing.

NOTE: The FaST system will not start until thesteering handles are rotated forward or backward.

NOTE: Do not enable the FaST system withconventional cleaning detergents in the solutiontank. Drain, raise and refill the solution tank withclear cool water only before operating the FaSTsystem. Conventional cleaning detergents/restorers may cause failure to the FaST solutionsystem.

ec-H2O SWITCH (OPTION)

The ec--H2O switch (option) enables the ec--H2O(electrically converted water) system. When theec--H2O system is enabled, it is turned on and offwith the scrub switch.

Enable the ec--H2O system: Press the top of theec--H2O switch.

Enable conventional scrubbing: Press the bottomof the ec--H2O switch.

NOTE: Disable the ec--H2O system before usingthe machine for conventional scrubbing.

NOTE: The ec--H2O system will not start until themachine starts scrubbing.

NOTE: Do not enable the ec--H2O system withconventional cleaning detergents in the solutiontank. Drain, raise and refill the solution tank withclear cool water only before operating the ec--H2Osystem. Conventional cleaning detergents/restorers may cause failure to the ec--H2Osolution system.

OPERATION

135700XP 331533 (9--06)

ES SWITCH (OPTION)

The ES switch turns on and off the solutionrecycling system.

On: Press the switch.

Off: Press the switch.

RECOVERY TANK FULL INDICATOR

The recovery tank full indicator comes on whenthe recovery tank is full. When the indicatorcomes on, the squeegee raises and the vacuumfan shuts off after a short delay.

OPERATION

5700XP 331533 (9--06)14

SCRUBBING SWITCH

The scrubbing switch controls the scrub brushes,squeegee and vacuum fan.

Start scrubbing: Press the switch. The indicatorlight will come on. The scrubbing system will startwhen the steering handles are rotated forward orbackward.

Stop scrubbing: Press the switch. The indicatorlight will go off. First the scrub brushes stop andraise, then vacuum stops and the squeegeeraises.

NOTE: The scrub switch also controls the FaSTsystem (option) when the FaST system is enabledwith the FaST switch.

BATTERY DISCHARGE INDICATOR

The battery discharge indicator shows the chargelevel of the batteries. It displays the charge levelwhen the machine is operating.

When the batteries are fully charged, the indicatoron the far right is lit. As the batteries discharge,the indicator will move along the display to theleft. The batteries should be recharged when theindicator flashes. The scrub head will raise, andthe vacuum fan and brushes will shut off. Thepropel will operate for a short time to allow theoperator to return the machine to the batterycharging area.

NOTE: The reading on the battery dischargeindicator is not accurate when the machine is firstpowered on. Operate the machine a few minutesbefore reading the charge level of the batteries.

NOTE: The battery discharge indicator will notreset from the flashing indicator unless thebatteries have been fully charged.

HOURMETER

The hourmeter records the number of hours themachine has been powered on. This informationis useful when servicing the machine.

OPERATION

155700XP 331533 (9--06)

ON-OFF KEY SWITCH

The on-off key switch controls machine powerwith a key.

On: Turn the key to the right.

Off: Turn the key to the left.

SQUEEGEE LEVER

The squeegee lever is used when scrubbing totemporarily lift the squeegee.

Raise squeegee: Pull the lever up, and move it tothe right to lock the lever in the up position.

Lower squeegee: Move the squeegee lever upand to the left to unlock it, and then release thelever.

POWER KILL SWITCH (OPTION)

The power kill switch halts all power to themachine.

Halt: Hit the power kill switch.

Restart: Turn the power kill switch to the right torelease the switch. Turn off the machine power,then turn on the machine power.

OPERATION

5700XP 331533 (3--08)16

CIRCUIT BREAKERS

The circuit breakers are resetable electrical circuitprotection devices. They stop the flow of currentin the event of a circuit overload. Once a circuitbreaker is tripped, reset manually by pressing thereset button after the breaker has cooled down.

If the overload that caused the circuit breaker totrip is still there, the circuit breaker will continue tostop current flow until the problem is corrected.

The circuit breakers are located on each side ofthe operator console.

The chart shows the circuit breakers and theelectrical components they protect.

CircuitBreaker Rating Circuit Protected

CB1 2.5 A Machine power

CB2 25 A Vacuum fan

CB2 40 A Heavy duty vacuum fan

CB3 25 A Machine propel

CB4 10 A Machine controls

CB5 20 A Scrub brush

CB5 35 A Heavy duty disk scrubbrush

CB6 20 A Scrub brush

CB6 35 A Heavy duty disk scrubbrush

OPERATION

175700XP 331533 (10--08)

FUSES (OPTION)

The fuse is a one-time protection devicedesigned to stop the flow of current in the event ofa circuit overload.

NOTE: Always replace the fuse with a fuse of thesame amperage.

The fuse is in--line and located near the air pumpon the front of the recovery tank.

Fuse Rating Circuit Protected

FU-1 10 A FaST (option)

FU-1 10 A ec--H2O (option)

SOLUTION TANK HOSE

The solution tank hose is used to drain thesolution tank. The drain hose plug is removed byturning the plug latch to loosen the plug andpulling the plug out of the drain hose. The drainhose is plugged by placing the hose plug in theend of the hose and turning the plug latch totighten the plug.

OPERATION

5700XP 331533 (9--06)18

RECOVERY TANK DRAIN HOSE

The recovery tank drain hose is used to drain therecovery tank. The drain hose plug is removed byturning the plug latch to loosen the plug andpulling the plug out of the drain hose. The drainhose is plugged by placing the hose plug in theend of the hose and turning the plug latch totighten the plug.

SUPPORT ARM

The support arm holds up the solution tank whenthe tank is lifted. The support arm engages whenthe solution tank is lifted all the way open. Thearm is released by pulling up on it.

STOP ARM

The stop arm prevents the solution tank from fullyclosing when the tank is lowered. Push the arm into lower the solution tank completely.

OPERATION

195700XP 331533 (9--06)

SQUEEGEE DOWN PRESSURE CAMS

The squeegee down pressure cams adjust thesqueegee deflection along the entire length of thesqueegee.

Increase: Turn the cams clockwise.

Decrease: Turn the cams counter-clockwise.

SQUEEGEE LEVELING KNOB

The squeegee leveling knob adjusts the deflectionat the ends of the squeegee.

Increase: Turn the squeegee leveling knobcounter-clockwise to increase the deflection at theend of the squeegees.

Decrease: Turn the squeegee leveling knobclockwise to decrease the deflection at the end ofthe squeegees.

PARKING BRAKE (OPTION)

The parking brake is controlled with a foot pedaland a release lever located by the squeegee.

Set: Push down on the foot pedal.

Release: Pull up on the release lever.

OPERATION

5700XP 331533 (9--06)20

HOW THE MACHINE WORKS

The scrub components of the machine are asolution tank, scrub brushes, a squeegee, avacuum fan, and a recovery tank.

Water and detergent, from the solution tank, flowto the floor through a solution valve to the scrubbrushes. The brushes scrub the floor. As themachine is moved forward the squeegee wipesthe dirty solution off the floor, which is then pickedup and drawn into the recovery tank.

The steering handles control the direction andspeed of the machine in forward or reverse. Byrotating the steering handles forward, the machinepropels forward. By rotating the handles towardsyou the machine propels backward.

When using the ES mode, the dirty solution in therecovery tank is filtered and returned to thesolution tank to be reused.

Three different widths of scrub heads andsqueegees are available for the machine, alongwith two different brush types.

The scrub head widths are as follows; the model700 (700 mm (28 in)), the model 800 (800 mm(32 in)), and the model 900 (900 mm (36 in)). The700 mm (28 in) squeegee is used with the 700model scrub head, as well as the 800 mm (32 in)with the model 800, and the 900 mm (36 in) withthe model 900. The two available brush types aredisk and cylindrical.

OPERATION

215700XP 331533 (3--08)

FaST SCRUBBING SYSTEM (OPTION)

The FaST (Foam Scrubbing Technology) systemoperates by injecting the FaST PAK concentrateagent (A) into the system with a small amount ofwater and compressed air. This mixture creates alarge volume of expanded wet foam.

The expanded foam mixture is then dispersedonto the floor (B) while the machine is scrubbing.When the squeegee picks up the mixture, thepatented foaming agent has collapsed and isrecovered into the recovery tank.

The FaST system can be used with all doublescrubbing and heavy duty scrubbing applications.

Using the FaST system can increase productivityby 30% by reducing your dump/fill cycle. It willalso reduce chemical usage and storage space.One FaST PAK of concentrated agent can scrubup to 1 million sq. ft.

NOTE: Do not enable the FaST system withconventional cleaning detergents in the solutiontank. Drain, raise and refill the solution tank withclear cool water only before operating the FaSTsystem. Conventional cleaning detergents/restorers may cause failure to the FaST solutionsystem.

NOTE: Storage or transporting machinesequipped with FaST in freezing temperaturesrequires special procedures. Check with aTENNANT representative for advice.

B

A

The Safe Scrubbing Alternativer

OPERATION

5700XP 331533 (10--08)22

ec-H2O SYSTEM (OPTION)

The ec--H2O (electrically converted water) systemoperates by producing electrically activated waterfor cleaning.

Normal water passes through a module where it isoxygenated and charged with an electric current.The electrically converted water changes into ablended acidic and alkaline solution forming aneutral pH cleaner. The converted water attacksthe dirt, breaks it into smaller particles, and pulls itoff the floor surface allowing the machine to easilyscrub away the suspended soil. The convertedwater then returns to normal water in the recoverytank.

The ec--H2O system can be used with all doublescrubbing applications.

NOTE: Do not enable the ec--H2O system withconventional cleaning detergents in the solutiontank. Drain, raise and refill the solution tank withclear cool water only before operating the ec--H2Osystem. Conventional cleaning detergents/restorers may cause failure to the ec--H2Osolution system.

OPERATION

235700XP 331533 (10--08)

PRE-OPERATION CHECKLIST

Check over this list of items before operating themachine:

- Check the battery fluid and charge level.

- Check the tank cover seals for damage andwear.

- Clean the vacuum fan inlet filter.

- Check the condition of the scrubbingbrushes. Remove any string, banding,plastic wrap, or other debris wrappedaround them.

- Check the squeegees for damage, wear andfor deflection adjustment.

- Check the vacuum hose for debris orblockage.

- ES machines; check the detergent tanklevel.

- Drain and clean the recovery tank.

- ES machines; drain and clean the solutiontank and ES filter. Rinse level sensors.

- Empty and clean the debris tray(if applicable).

- Check the service records to determinemaintenance requirements.

- FaST Scrubbing: Check the FaST PAK(option) concentrate agent level, replacecarton as needed. See the INSTALLINGTHE FaST PAK AGENT section of themanual.

- FaST or ec-H2O Scrubbing: Check that allconventional cleaning agents/restorers aredrained and rinsed from the solution tank.

- FaST or ec-H2O Scrubbing: Check thatthe solution tank is filled with clear coolwater only.

OPERATION

5700XP 331533 (9--06)24

INSTALLING FaST PAK AGENT (OPTION)

NOTE: Machine must be equipped with the FaSToption before the FaST PAK agent can beinstalled.

1. Remove the perforated knock--outs from theFaST PAK Floor Cleaning Concentratecarton. Do not remove the bag from thecarton. Pull out the bag’s hose connector onthe bottom of the bag and remove the hosecap from the connector.

NOTE: The FaST PAK Floor CleaningConcentrate is specifically designed for usewith the FaST system scrubbing application.NEVER use a substitute, machine damage willresult.

FOR SAFETY: When using machine,always follow the handling instructionson chemical container.

2. Empty the solution tank. See the DRAININGAND CLEANING THE TANKS section of themanual.

NOTE: When scrubbing with the FaST systemoption, use clean water only. Do not add cleaningagents in the solution tank. Conventional cleaningagents/restorers may cause failure to the FaSTsolution system..

3. Raise the solution tank and remove the frontcover to access the FaST PAK carton.

OPERATION

255700XP 331533 (10--08)

4. Place the FaST PAK carton in the cartonholder under the front cover of the machine.Connect the supply hose to the FaST PAKbag.

NOTE: If any dried concentrate is visible on thesupply hose connector or the on the FaST PAKconnector, soak and clean with warm water.

5. Make sure to connect the supply hose ontothe hose storing plug when the supply hoseis not connected to the FaST PAK. This willprevent the FaST solution system fromdrying out and clogging up the hose.

6. When replacing an empty FaST PAK carton,allow the new FaST PAK detergent togravity feed into the system for severalminutes prior to operating the FaST system.If the detergent does not flow out of theFaST PAK, simply squeeze and release thehose several times. If the previous FaSTPAK was run dry, it may take up to 3minutes of operation to remove any airpockets in the system before you achievemaximum foaming.

OPERATION

5700XP 331533 (9--06)26

STARTING THE MACHINE

1 Turn the machine power on.

2 Release the machine parking brake, if yourmachine has this option.

FILLING THE TANKS

1. Start the machine.

2. Drive the machine to the filling site.

OPERATION

275700XP 331533 (9--06)

3. Turn the machine power off.

FOR SAFETY: Before leaving orservicing machine, stop on levelsurface, set parking brake (if soequipped), turn off machine, andremove key.

4. Set the parking brake, if your machine hasthis option.

NOTE: If you are going to scrub in the ES mode,the recovery tank can be partially filled to extendscrub time. Make sure the ES system is on.

If you do not want to use the ES system, makesure the ES system is off. DO NOT fill therecovery tank.

5. ES mode: Lift up the solution tank. Fill therecovery tank with water 50 mm (2 in) belowthe top of the ES filter located on the bottomof the tank, approximately 87 L(23 gal) of water.

OPERATION

5700XP 331533 (10--08)28

6. ES mode: Lower the solution tank.

7. CONVENTIONAL SCRUBBING: Open thesolution tank cover and partially fill thesolution tank with water. Pour the requiredamount of detergent into the solution tank fillopening. Continue filling the solution tankwith water 25 mm (1 in) below the bottom ofthe solution fill opening channel.

FOR SAFETY: Follow mixing andhandling instructions on chemicalcontainers.

8. FaST or ec--H2O SCRUBBING: Open thesolution tank cover and fill the solution tankwith clear cool water only.

NOTE: When cleaning using the FaST orec-H2O option, USE CLEAR COOL WATERONLY. DO NOT add cleaning agents insolution tank. Conventional cleaningagents/restorers may cause failure to thesystem.

NOTE: (For conventional scrubbing)Floor conditions, water condition, amount ofsoilage, types of soilage, and brush action all playan important role in determining the type andconcentration of detergent used. For specificrecommendations, contact your Tennantrepresentative.

WARNING: Flammable materials cancause an explosion or fire. Do not useflammable materials in tank(s).

OPERATION

295700XP 331533 (9--06)

NORMAL SCRUBBING

D Pick up oversized debris before scrubbing.Pick up pieces of wire, string, twine, etc.,which could become wrapped around thescrub brush.

D Plan the scrubbing in advance. Try toarrange long runs with minimum stoppingand starting. Do an entire floor or section atone time.

D Try to scrub as straight a path as possible.Avoid bumping into posts or scraping thesides of the machine. When scrubbing deadend aisles, start at the closed end of theaisle and scrub your way out. Overlap thescrub paths by a few centimeters (inches).

D If you see poor scrubbing performance, stopscrubbing and refer to MACHINETROUBLESHOOTING.

Non-scuff polypropylene scrub brush -- Thisbrush uses a softer, general purposepolypropylene bristle to lift lightly compactedsoilage without scuffing high-gloss coated floors.

Nylon scrub brush -- Recommended forscrubbing coated floors. Cleans without scuffing.

Super abrasive bristle scrub brush -- Nylonfiber impregnated with abrasive grit to removestains and soilage. Strong action on any surface,performing well on buildup, grease, or tire marks.

Heavy duty stripping pad -- This black pad is forstripping floors. Cuts through old heavy finisheseasier, to prepare the floor for re-coating.

Stripping pad -- This brown pad is for strippingfloors. Quickly and easily cuts through old finish toprepare the floor for re-coating.

Scrubbing pad -- This blue pad is for scrubbingfloors. Removes dirt, spills and scuffs, leaving aclean surface ready for re-coating.

Buffing pad -- This red pad is for buffing floors.Quickly cleans and removes scuff marks whilepolishing the floor to a high gloss.

Polishing pad -- This white pad is for polishingfloors. Maintains a high gloss. Use for buffing verysoft finishes and lower traffic areas, or use forpolishing soft waxes on wood floors.

07218

OPERATION

5700XP 331533 (9--06)30

Cylindrical polypropylene scrub brush -- Thiscylindrical brush uses a softer, general purposepolypropylene bristle to lift lightly compactedsoilage without scuffing high-gloss coated floors.

Cylindrical nylon scrub brush -- This cylindricalbrush is recommended for scrubbing coatedfloors. Cleans without scuffing.

Cylindrical super abrasive bristle scrub brush-- Nylon fiber impregnated with abrasive grit toremove stains and soilage. Strong action on anysurface, performing well on buildup, grease, or tiremarks.

NOTE: Cylindrical scrub brushes must beinstalled with the herringbone patterns on thebrushes pointing towards each other for bestdebris pick up.

1. Start the machine.

2. Drive the machine to the area to bescrubbed.

OPERATION

315700XP 331533 (10--08)

3. FaST SCRUBBING: Press the top of theFaST switch to start the FaST system.

NOTE: When using the FaST system (option), thesolution flow lever is nonfunctional. The FaSTsystem flow rate is pre--set.

NOTE: Leave the FaST switch in theCONVENTIONAL SCRUBBING position if notusing the FaST system.

ec--H2O SCRUBBING: Press the top of theec--H2O switch to start the ec--H2O system.

NOTE: When using the ec--H2O system (option),the solution flow lever is nonfunctional. Theec--H2O system flow rate is pre--set. The ec--H2Omodule has optional flow rate settings. If solutionflow adjustments are required, contact anAuthorized Service Center.

NOTE: Leave the ec--H2O switch in theCONVENTIONAL SCRUBBING position if notusing the ec--H2O system.

NOTE: The ec--H2O system indicator light will notturn on until the machine starts scrubbing.

ec--H2O SCRUBBING: If an alarm sounds andthe ec--H2O system indicator light begins to blinkred, the ec--H2O module must be flushed toresume ec--H2O operation (See ec--H2OMODULE FLUSH PROCEDURE)

NOTE: When the alarm sounds and the lightblinks red, the machine will bypass the ec--H2Osystem. To continue scrubbing, turn the ec--H2Oswitch off and change over to conventionalscrubbing.

ATTENTION: (ec-H2O model) Do not allowsolution tank to run dry. ec-H2O modulefailure may result if operated without water foran extended period.

ec-H2O SYSTEMINDICATOR LIGHT CODE CONDITION

Solid green Normal operation

Blinking red Flush ec--H2O module

Solid red Contact Service Center

OPERATION

5700XP 331533 (10--08)32

4. Press the scrubbing switch.

5. Adjust the solution flow to the floor asneeded.


6. Drive the machine forward and scrub asrequired.


OPERATION

335700XP 331533 (10--08)

DOUBLE SCRUBBING

Double scrubbing is a method for removing heavyfloor accumulations. This is done by making twopasses over the area to be cleaned with themachine.

Double scrubbing can be performed using theFaST SCRUBBING SYSTEM (option),ec--H2O SCRUBBING SYSTEM (option) orCONVENTIONAL SCRUBBING methods.

First, make a pass over the area scrubbing withthe squeegee up. This dispenses solution over thearea allowing the solution to soak on the floor. Letthe solution remain on the floor for 15 to20 minutes. Then make a second pass scrubbingwith the squeegee down.


FOR SAFETY: When using machine, goslow on inclines and slippery surfaces.

OPERATION

5700XP 331533 (9--06)34

STOP SCRUBBING

1. Release the steering handles.

2. Press the scrubbing switch.

OPERATION

355700XP 331533 (9--06)

DRAINING AND CLEANING THE TANKS

When you are finished scrubbing, or when therecovery tank full indicator comes on, therecovery tank should be drained and cleaned. Thesolution tank then can be filled again for additionalscrubbing.

If you used the machine in ES mode, the solutiontank should also be drained and cleaned whenyou are finished scrubbing.

1. Stop scrubbing.

2. Drive the machine next to a floor drain orsink.


FOR SAFETY: Before leaving orservicing machine, stop on levelsurface, and turn off machine.


OPERATION

5700XP 331533 (9--06)36

5. ES mode: Remove the solution tank drainhose from the mounting clip.

6. ES mode: Remove the drain hose plugwhile holding the hose up, then slowly lowerthe drain hose to the floor drain.

7. ES mode: Lift the solution tank cover andflush out the solution tank with clean waterthrough the fill opening and the top accesshole. Rinse the filter(s) at the bottom of thesolution tank.

NOTE: Do not use steam to clean the tank.

8. ES mode: When the solution tank hascompletely drained, replace the drain hoseplug in the solution tank drain hose andplace the solution tank drain hose back ontothe mounting clip on the machine.

OPERATION

375700XP 331533 (3--08)

9. Remove the recovery tank drain hose fromthe mounting clip.

10. Remove the drain hose plug while holdingthe hose up, then slowly lower the drainhose to the floor drain or sink.

11. Lift the solution tank to reach the recoverytank.

12. Flush out the inside of the recovery tank withclean water.


OPERATION

5700XP 331533 (3--08)38

13. ES mode: Rinse the ES filter.

14. Rinse and wipe off the level sensor(s) on theside of the recovery tank.

15. Remove and clean the vacuum fan filterlocated in the recovery tank. Clean byshaking dust or rinsing pleats with lowpressure water. Insert the filter back in to therecovery tank when finished.

NOTE: Be sure the vacuum filter is dry beforereinstalling it in the machine.

16. An optional debris screen is available for therecovery tank entry. If your machine isequipped with this screen, remove and cleanit daily.

OPERATION

395700XP 331533 (9--06)

17. When the tank has completely drained,replace the drain hose plug in the recoverytank drain hose. Place the recovery tankdrain hose back onto the mounting clip onthe machine.

18. Pull up on the support arm and lower thesolution tank. Push the stop arm in tocompletely lower the solution tank.

19. Cylindrical scrub head: Remove and cleanthe debris trough. Place the trough back inthe scrub head.

OPERATION

5700XP 331533 (9--06)40

STOP THE MACHINE

1. Stop scrubbing.


3. Set the parking brake, if your machine hasthat option.

FOR SAFETY: Before leaving orservicing machine, stop on levelsurface, set parking brake (if soequipped), turn off machine, andremove key.

OPERATION ON INCLINES

Drive the machine slowly on inclines.

FOR SAFETY: When using machine, goslow on inclines and slippery surfaces.

The maximum rated climb and descent inclinewith empty tanks is 8_, with full tanks is 6_.

OPERATION

415700XP 331533 (9--06)

POST-OPERATION CHECKLIST

Check over this list of items after you havefinished scrubbing with the machine powered on:

- Check the battery fluid and charge level.

NOTE: The reading on the battery dischargeindicator is not accurate when the machine is firstpowered on. Operate the machine a few minutesbefore reading the charge level of the batteries.

Check over this list of items with the machinepowered off:

- Check the tank cover seals for damage andwear.

- Clean the vacuum fan inlet filter.

- Check the condition of the scrubbingbrushes. Remove any string, banding,plastic wrap, or other debris wrappedaround them.

- Check the squeegees for damage, wear andfor deflection adjustment.

- Check the vacuum hose for debris orblockage.

- ES machines; check the detergent tanklevel.

- Drain and clean the recovery tank.

- ES machines; drain and clean the solutiontank and ES filter. Rinse level sensors.

- Empty and clean the debris tray. (ifapplicable).

- Check the service records to determinemaintenance requirements.

- FaST scrubbing: If FaST PAK is empty afterscrubbing, install a new FaST PAK orconnect supply hose to the storage plug.

OPERATION

5700XP 331533 (9--06)42

MACHINE TROUBLESHOOTING

Problem Cause RemedyTrailing water -- poor or no waterpickup

Worn squeegee blades Rotate or replace squeegee blades

Squeegee out of adjustment Adjust squeegeeVacuum hose clogged Flush vacuum hosesVacuum fan screen dirty Clean inlet screenDebris caught on squeegee Remove debrisVacuum hose to squeegee orrecovery tank disconnected ordamaged

Reconnect or replace vacuum hose

Solution tank not completely closed Check for obstructionsHeavy duty batteries posts too tall,file down posts

Machine front cover mounted toohigh, mount cover lower

Torn seals on solution tank Replace sealsVacuum fan will not turn on Recovery tank full Drain recovery tank

Foam filling recovery tank Empty recovery tankUse less or change detergentUse a defoamer

Vacuum fan circuit breaker tripped Reset circuit breakerVacuum fan will not turn on, opticalsensor(s)

Recovery tank full sensor(s) dirty Clean sensor(s) and reset key switchOily/ink film buildup on recovery tanksensor(s)

Use correct detergentChange to magnetic sensor(s)

Operating in bright sunlight Install sensor sun shield(s)Little or no solution flow to the floor Solution tank empty Fill solution tank

Solution control cable broken or outof adjustment

Replace and/or adjust cable

Solution flow turned off Turn solution flow onSolution supply lines plugged Flush solution supply linesSolution supply line filter dirty Clean filterSolution solenoid clogged or stuck Clean or replaceES mode: ES switch off Turn ES switch on

Poor scrubbing performance Debris caught on scrub brushes Remove debrisImproper detergent, brush, or padused

Contact Service Center

Worn scrub brush(es) or pad(s) Replace scrub brush(es) or pad(s)Scrub brush motor circuit breaker(s)tripped

Reset circuit breaker(s)

Reduce scrub brush down pressureUneven brush pressure, level scrubhead

Broken brush drive belts oncylindrical scrub head, replace belt

Contact Service CenterLow battery charge Charge batteries until the charger

automatically turns off

Tire pressure low Increase tire pressure

OPERATION

435700XP 331533 (10--08)

Problem Cause Remedy

Poor propelling traction Brush pressure set too high Decrease brush pressureTires slip on oily or waxed floors Contact Service CenterUneven brush down pressure Level scrub head

Broken brush drive belts oncylindrical scrub head, replace belt

FaST System (option) does notoperate

FaST switch is set for Conventionalscrubbing

Set the FaST switch for FaST systemscrubbing

FaST fuse blown Determine cause and replace the10A fuse

Clogged FaST PAK supply hoseand/or connectors

Soak connector and hose in warmwater and clean

FaST PAK carton is empty or notconnected

Replace FaST PAK carton and/orconnect supply hose

Clogged flow control orifice and/orscreen

Remove and clean orifice and/orscreen

Faulty pump or air compressor Contact Service CenterClogged filter screen Drain solution tank, remove and

clean filter screen

FaST system is not primed To prime, operate the FaST solutionsystem for 3 minutes.

ec-H2O Model:ec--H2O system indicator lightblinking red

Mineral deposit build--up in module Flush module (See ec--H2OMODULE FLUSH PROCEDURE)

ec-H2O Model:Alarm sounds

ec-H2O Model:ec--H2O system indicator light solidred

Defective module Contact Service Center

ec-H2O Model:ec--H2O system indicator light doesnot turn on

Defective light or module Contact Service Center

ec-H2O Model:No water flow

Clogged module Contact Service CenterDefective solution pump Replace solution pump

OPERATION

5700XP 331533 (9--06)44

OPTIONS

VACUUM WAND

The vacuum wand uses the machine’s vacuumsystem. The vacuum hose allows pick-up of spillsthat are out of reach of the machine.





OPERATION

455700XP 331533 (9--06)

3. Remove the squeegee suction hose fromthe top of the squeegee.

4. Put together the wand and the wand hose.

5. Connect the vacuum wand hose and thesqueegee suction hose with the adapter.

6. Turn the machine power on.

10080

OPERATION

5700XP 331533 (9--06)46

7. Lower the squeegee with the squeegeeswitch to turn the vacuum system on.

8. Vacuum the floor.

9. When finished, raise the squeegee to shutoff the vacuum.

10.Turn the machine power off.

06599

OPERATION

475700XP 331533 (9--06)

11. Remove the vacuum hose from thesqueegee suction hose.

12. Reconnect the squeegee suction hose to thetop of the squeegee.

OPERATION

5700XP 331533 (9--06)48

POWER WAND

The power wand uses the machine’s vacuum andsolution systems. The power wand allowsscrubbing of floors that are out of reach of themachine.





3. Remove the squeegee suction hose fromthe top of the squeegee.

OPERATION

495700XP 331533 (9--06)

4. Connect the vacuum wand hose and thesqueegee suction hose with the adapter.

5. Open the solution tank cover. Attach the endof solution hose to the quick-disconnect.Push the connector in until it stops. Pull onthe hose to make sure it is connected.

6. Attach the other ends of the solution andvacuum hoses to the power wand.


OPERATION

5700XP 331533 (9--06)50

8. Lower the squeegee with the squeegeeswitch to turn the vacuum system on.

9. Switch the power wand on.

10. Squeeze the solution lever on the powerwand to spray solution on the floor. Scrubthe floor with the brush side of the cleaningtool.

11. Vacuum up the solution by turning over thecleaning tool so the squeegee side is down.

06202

OPERATION

515700XP 331533 (9--06)

If the cleaning tool is hard to push or is notpicking up the solution very well, adjust theroller wheels on the tool by turning the blackadjustment knob.

NOTE: The wheels are properly adjusted whenthe squeegee blades deflect slightly while the toolis pushed back and forth.

12. When finished, switch the power wand off.

13. When finished, raise the squeegee to shutoff the vacuum.

14. Disconnect the solution hose from themachine.

06604

OPERATION

5700XP 331533 (9--06)52

15. Remove the vacuum hose from thesqueegee suction hose.

16. Disconnect the other ends of the solutionand vacuum hoses from the power wand.

17.Turn the machine power off.

18. Reconnect the squeegee suction hose to thesqueegee.

MAINTENANCE

535700XP 331533 (3--08)

MAINTENANCE

1

2

3

4

56

7

8

9

10

11

68

12

12

10066, 10190

MAINTENANCE CHART

Interval Key Description ProcedureLubricant/

Fluid

No. ofServicePoints

Daily 2 Squeegee Check for damage and wear -- 1Check deflection and leveling -- 1

8 Scrub brushes or pads Check for damage and wear -- 2

1 Recovery tank Clean tank -- 1Clean level sensor -- 1(2)Clean vacuum fan filter -- 1Clean debris screen (option) -- 1

1 Recovery tank, ES mode Clean ES filter -- 13 Solution tank, ES mode Clean -- 13 Vacuum fan filter Clean -- 1

Machine Check for leaks -- 1

6 Disk scrub head skirt Check adjustment -- 1Check for damage and wear -- 1

6 Cylindrical scrub headskirts

Check adjustment -- 4Check for damage and wear -- 4

12 FaST PAK supply hoseand connector (option)

Clean and connect hose to stor-ing plug when not in use

-- 1

50 Hours 5 Front tires Check air pressure -- 28 Cylindrical brushes Check taper and rotate front to

rear-- 2

12 FaST Filter screen(option)

Clean -- 1

MAINTENANCE

5700XP 331533 (3--08)54

Interval Key Description ProcedureLubricant/

Fluid

No. ofServicePoints

100 Hours 4 Rear casters Lubricate SPL 29 Cylindrical scrub brush

drive beltsCheck tension -- 2

500 Hours 10 Vacuum fan motor Check motor brushes -- 1

1000Hours

12 FaST water and air filters(option)

Replace -- 1

7 Scrub brush motors Check motor brushes -- 211 Propelling motor Check motor brushes -- 111 Transaxle Check lubricant level GL 1

SPL -- Special lubricant, Lubriplate EMB grease (TENNANT part no. 01433--1)GL -- SAE 90 weight gear lubricant

MAINTENANCE

555700XP 331533 (9--06)

LUBRICATION

REAR CASTERS

The rear casters each have one grease fitting onthe caster swivel. Lubricate the caster with agrease gun containing Lubriplate EMB grease(TENNANT part no. 01433--1) every 100 hours ofmachine operation.

TRANSAXLE

Check the transaxle lubricant level every 1000hours of operation by removing one of the orangefiller plugs. If needed, add SAE 90 weight gearlubricant.

BATTERIES

The batteries are unique in that they hold theirpower for long periods of time. The lifetime of thebatteries is limited by the number of charges thebatteries receive. To get the most life from thebatteries, charge them when the battery dischargeindicator blinks.

Periodically clean the top surface of the batteriesand the terminals, and check for looseconnections. Use a strong solution of baking sodaand water. Brush the solution sparingly over thebattery tops, terminals, and cable clamps. Do notallow any baking soda solution to enter thebatteries. Use a wire brush to clean the terminalposts and the cable connectors. After cleaning,apply a coating of clear battery post protectant tothe terminals and the cable connectors. Keep thetops of the batteries clean and dry.

MAINTENANCE

5700XP 331533 (9--06)56

Keep all metallic objects off the top of thebatteries, which may cause a short circuit.Replace any worn or damaged wires.

Check the electrolyte level in each battery cellbefore and after charging, and after every 50hours of operation. Do not charge the batteriesunless the fluid is slightly above the battery plates.If needed, add just enough distilled water to coverthe plates. Never add acid to the batteries. Do notoverfill. Always keep the battery caps on, exceptwhen adding water or taking hydrometer readings.

Measuring the specific gravity, using ahydrometer, is a way to determine the chargelevel and condition of the batteries. If one or moreof the battery cells test lower than the otherbattery cells (0.050 or more), the cell is damaged,shorted, or is about to fail.

NOTE: Do not take readings immediately afteradding distilled water. If the water and acid are notthoroughly mixed, the readings may not beaccurate. Check the hydrometer readings againstthe following chart to determine the remainingbattery charge level:

SPECIFIC GRAVITY

at 27_ C (80_F)

BATTERY

CHARGE

1.265 100% Charged

1.223 75% Charged

1.185 50% Charged

1.148 25% Charged

1.110 Discharged

NOTE: If the readings are taken when the batteryelectrolyte is any temperature other than 27_ C(80_ F), the reading must be temperaturecorrected. Add or subtract to the specific gravityreading 0.004, 4 points, for each 6_ C (10_ F)above or below 27_C (80_ F).

04380

MAINTENANCE

575700XP 331533 (9--06)

CHARGING THE BATTERIES

1. Drive the machine to a flat, dry surface in awell-ventilated area.

2. Turn the machine power off and set theparking brake if your machine has thisoption.


3. Lift up the solution tank to get access to thebatteries.

NOTE: The solution tank must be empty.

4. Check the water level in all the battery cells.

5. If the level is low, add just enough distilledwater to cover the battery plates. DO NOTOVERFILL. The batteries can overflowduring charging due to expansion.

NOTE: Make sure the battery caps are in placewhile charging.

FOR SAFETY: When maintaining orservicing machine, avoid contact withbattery acid.

00879

MAINTENANCE

5700XP 331533 (9--06)58

6. Plug the charger connector into the batteryconnector.

WARNING: Batteries emit hydrogengas. Explosion or fire can result. Keepsparks and open flame away. Keepcovers open when charging.

7. Plug the battery charger into the wall outlet.

NOTE: If the red “ABNORMAL CYCLE” lamplights when the TENNANT charger is plugged intoa wall outlet, the charger cannot charge thebattery and there is something wrong with thebattery.

8. The TENNANT charger will startautomatically. When the batteries are fullycharged, the TENNANT charger willautomatically turn off.

9. After the charger has turned off, unplug thecharger from the wall outlet.

10.Unplug the charger connector from thebattery connector on the machine.

FOR SAFETY: When maintaining orservicing machine, avoid contact withbattery acid.

11. Check the electrolyte level in each batterycell after charging. If needed, add distilledwater to raise the electrolyte level to about12 mm (0.4 in) below the bottom of the sighttubes.

12. Lower the solution tank.

13. Pull up on the support arm and rotate thestop arm out of the way to allow the solutiontank to close completely.

MAINTENANCE

595700XP 331533 (9--06)

TOUCH PANEL

The touch panel can be used to run aself-diagnostic test of the machine electricalcomponents and system.


2. While pressing the squeegee switch, turnthe machine power on. Continue pressingthe squeegee switch a few seconds, thenrelease the switch.

3. While the diagnostic is running, the threespeed switch indicators will flash. Themachine systems will activate as follows:

D The brushes and squeegee raise.

D The vacuum fan starts and thesqueegee lowers. The squeegee raisesand the vacuum fan shuts off.

D The scrub head lowers and raises.

D The brushes turn on and off.

D The solution valve turns on and off.

D The ESt pump turns on and off, if themachine has the ESt option.

D The vacuum fan starts and shuts off.

D The brushes turn on and off.

MAINTENANCE

5700XP 331533 (10--08)60

If the self-diagnostic test finds an error in thesystem, the error will be displayed by thebrush pressure switch indicators. Note whichof the indicators are on, and contact theservice personnel.

4. Turn off the diagnostic by turning off themachine power.

ELECTRIC MOTORS

The carbon brushes on the vacuum fan motorshould be inspected after every 500 hours ofmachine operation. The carbon brushes on thescrub brush motors and propelling motor shouldbe inspected after every 1000 hours of machineoperation.

MAINTENANCE

615700XP 331533 (9--06)

SCRUB HEAD

The machine can be equipped with either a diskbrush, or cylindrical brush scrub head. Both scrubheads contain skirts to control over-spray from thescrub brushes.

DISK BRUSH SCRUB HEAD SKIRT

Make sure the scrub head skirt touches the floorall the way around when the scrub head islowered. Check the skirt for damage or wear daily.

ADJUSTING THE SCRUB HEAD SKIRT

1. Lower the scrub head on a level floor.



3. Check to see if the scrub head skirt touchesthe floor all the way around the scrub head.

4. If the skirt needs to be adjusted, pull thestrap end away from the skirt. Loosen thestrap from the buckle, and move the skirt upor down to touch the floor.

NOTE: Replace the scrub head skirt when it isdamaged or no longer is able to touch the floor.

5. Pull the strap tight through the buckle, andattach the strap end to the skirt using thehook and loop fastener.

6. Raise the scrub head.

MAINTENANCE

5700XP 331533 (9--06)62

REPLACING THE SCRUB HEAD SKIRT

1. Lower the scrub head.



3. Pull the strap end away from the skirt.Loosen and pull the strap from the buckle.

4. Pull the old skirt off the scrub head.

5. Put the new skirt on the scrub head, liningup the notches under the rollers.

6. Pull the strap tight through the buckle, andattach the strap end to the skirt using thehook and loop fastener.

7. Adjust the skirt as stated in ADJUSTINGTHE SCRUB HEAD SKIRT.

MAINTENANCE

635700XP 331533 (9--06)

CYLINDRICAL BRUSH SCRUB HEAD SKIRTS

The four head skirts should just touch the floor.Check the skirts for damage or wear daily.

ADJUSTING THE SCRUB HEAD SKIRTS

1. Lower the scrub head on a level floor.



3. Check to see if the scrub head skirts touchthe floor.

4. If any of the skirts needs adjusting, loosenthe retainer strip hardware and slide the skirtto the proper adjustment. Tighten theretainer strip hardware.

REPLACING THE SCRUB HEAD SKIRTS




3. Remove the retainer strip and hardware.

4. Replace the old skirt with a new skirt andmount in place with the retainer strip andhardware.

MAINTENANCE

5700XP 331533 (3--08)64

REMOVING OR REPLACING THE SCRUBHEAD

The scrub heads are available in two brush types,and three widths. The scrub heads areinterchangeable when the scrub brush motorcircuit breakers, installed in the operator console,match the circuit breakers needed as shown inthe following chart:

SCRUB HEAD/CIRCUIT BREAKERS

Scrub head Disk HD Disk Cylindrical

Model 700700 mm(28 in)

20 A -- 20 A


20 A 35 A 20 A


-- 35 A 20 A

NOTE: To interchange the model 800 or themodel 900 heavy duty disk head with one of theother available scrub heads, you must change thescrub brush motor circuit breakers in the operatorconsole. Interchanging the scrub heads withoutchanging the scrub brush motor circuit breakerswill cause the scrub brush motors or circuitbreakers to fail.

NOTE: When you change to a different widthscrub head, be sure to install the appropriatewidth squeegee and machine front cover.

1. Lower the scrub head.



3. Remove the machine front cover.

MAINTENANCE

655700XP 331533 (9--06)

4. Disconnect the solution line from the scrubhead tee fitting.

5. Disconnect the wire harness.

6. Disconnect the scrub head from the guideby removing the clevis pin.

7. Disconnect the lift arms from the scrub headby removing the two clevis pins.

MAINTENANCE

5700XP 331533 (9--06)66

8. Disconnect the actuator from the scrub headby removing the clevis pin.

9. To install the scrub head, connect the liftarms to the scrub head with the two clevispins.

10. Connect the scrub head to the guide withthe clevis pin.

11. Connect the actuator to the scrub head withthe clevis pin.

12. Connect the wire harness.

13. Connect the solution line to the scrub headtee fitting.

LEVELING THE SCRUB HEAD

NOTE: Check the tires for correct tire pressurebefore leveling the scrub head.

1. Make sure the scrub head is lowered to thefloor.

2. Check the level of the scrub head bymeasuring the distance from the top of thescrub head, to the floor at all four corners.The scrub head should measure the sameon all four corners.

MAINTENANCE

675700XP 331533 (9--06)

3. If the scrub head is not level at all fourcorners, loosen the jam nut on theadjustment screw located on the top of thescrub head. Turn the adjustment screw untilthe scrub head measures level. Tighten thejam nut.

4. Install the machine front cover.

5. Cylindrical scrub head: Check the brushpattern as described in CHECKING ANDADJUSTING CYLINDRICAL BRUSHPATTERN.

MAINTENANCE

5700XP 331533 (9--06)68

SCRUB BRUSHES

The scrub brushes should be checked daily forwire or string tangled around the brush or brushdrive hub. The brushes should also be checkedfor any damage and wear.

DISK BRUSHES

The disk brushes should be replaced if largeamounts of bristles are missing, or if theremaining bristles’ length is less than 10 mm(0.38 in).

NOTE: Be sure to replace brushes in sets.Otherwise one brush will be more aggressive thanthe other.

Cleaning pads must be placed on pad drivesbefore they are ready to use. The cleaning pad isheld in place by a pad holder.

Cleaning pads need to be cleaned immediatelyafter using with soap and water. Do not wash thepads with a pressure washer. Hang dry pads, orlie flat to dry.

REPLACING THE DISK BRUSHES




3. Open the access cover on either corner ofthe scrub head.

MAINTENANCE

695700XP 331533 (9--06)

4. Turn the brush until you can see the brushspring clip.

5. Press the brush spring clip together withyour thumb and index finger. The brush willdrop off the brush drive hub.

6. Pull the brush out from under the scrubhead.

7. Place the new scrub brush on the floor infront of the scrub head. Push the brushunder the scrub head.

8. Line up the brush drive socket with the driveplug.

9. Lift the scrub brush into the drive plug.

10. Check to make sure the brush is securelymounted on the brush drive hub.

11. Close the scrub head access cover.

12. Repeat for the other brush.

MAINTENANCE

5700XP 331533 (9--06)70

CYLINDRICAL BRUSHES

Check the brush taper and rotate the brushesfrom front-to-rear every 50 hours of operation, formaximum brush life and best scrubbingperformance.

The cylinder brushes should be replaced if largeamounts of bristles are missing, or if theremaining bristles’ length is less than 10 mm(0.38 in).

NOTE: Be sure to replace brushes in sets.Otherwise one brush will be more aggressive thanthe other.

REPLACING THE CYLINDRICAL BRUSHES




3. Push down on the mounting spring and theidler door, then pull out on the bottom of thedoor. Push down on the spring until the doorreleases from the scrub head. Pull the idleplug off the brush.

4. Pull the brush out of the scrub head.

5. With the double row end of the brushtowards you, guide the brush onto the drivehub.

NOTE: Use the double rows on the idler end ofthe brush.

MAINTENANCE

715700XP 331533 (9--06)

6. Insert the Idler plug of the idler door into thebrush.

7. Push down on the door to catch the door inthe scrub head, then pull up on the door tolatch it in the spring.

8. Repeat for the other brush on the other sideof the scrub head.

NOTE: The idler doors have stamped letters thatcorrespond with letters on the scrub head. Makesure the idler doors are placed back on the sameside of the scrub head that they were originallyremoved from.

CHECKING AND ADJUSTING CYLINDRICALBRUSH PATTERN

NOTE: Check the tires for correct tire pressureand make sure the solution tank is full beforechecking or adjusting the brush pattern.

1. Apply chalk, or some other material that willnot blow easily away, to a smooth, levelfloor.

2. Raise the scrub head. Position the scrubhead over the chalked area.

3. Set the parking brake if your machine hasthis option.

4. Lower the scrub head for 15 to 20 secondswhile keeping the scrub head in one spot inthe chalked area.

NOTE: If chalk or other material is not available,allow the brushes to spin on the floor for twominutes. A polish mark will remain on the floor.

5. Raise the scrub head and move the machineaway from the chalked area. Turn themachine power off.

MAINTENANCE

5700XP 331533 (9--06)72

6. Observe the shape of the brush patterns. Ifthe brush patterns have parallel sides, thebrushes do not need taper adjustment.

If one or both of the brush patterns aretapered, the brushes will have to be adjustedto straighten the brush pattern.

A. Remove the idler door by pushing downon the mounting spring and the idlerdoor, then pulling out on the bottom ofthe door. Push down on the spring untilthe door releases from the scrub head.Pull the idle plug off the brush.

B. While holding the flat end of the idlershaft with a wrench, loosen themounting screw on the outside of theidler door.

10355

10356

MAINTENANCE

735700XP 331533 (9--06)

C. Turn the idler shaft to raise or lower theend of the brush as needed tostraighten the brush pattern. Tightenthe mounting screw.

D. Check the brush patterns again andreadjust as necessary.

The brush patterns should be the samewidth. If one is narrower then the other,loosen the jam nut on the adjustment screwlocated on the top of the scrub head.

Turn the adjustment screw clockwise toincrease the front brush pattern width. Turnthe adjustment screw counter-clockwise toincrease the back brush pattern width.Check the brush patterns again. Adjust untilthe front and back patterns are the samewidth.

Tighten the jam nut.

SOLUTION SYSTEM

RECOVERY TANK

The recovery tank stores recovered solution. Therecovery tank should be drained and cleaneddaily. The outside of the tank can be cleaned withvinyl cleaner.

Rinse and wipe off the level sensors daily. Thelevel sensors are located inside the recovery tank.

MAINTENANCE

5700XP 331533 (3--08)74

ES option: The ES filter should be cleaned daily.


A vacuum fan filter is located in the recovery tank.Remove and clean this filter daily. Clean byshaking dust or rinsing pleats with low pressurewater.

NOTE: Be sure the vacuum filter is dry beforereinstalling it in the machine.

An optional debris screen is available for therecovery tank entry. If your machine is equippedwith this screen, remove and clean it daily.

SOLUTION TANK

The solution tank stores the cleaning solution.

The solution tank does not require regularmaintenance. If deposits form on the bottom ofthe tank, rinse the tank with a strong blast ofwarm water. The tank can be flushed through thefill opening and top access hole.

ES option: The solution tank should be drainedand cleaned daily.

The solution tank contains one standard solutionline filter, and one solution line filter for the powerwand option. If the filters become dirty, thesolution flow will be reduced. Check and cleanthese filters if necessary.


MAINTENANCE

755700XP 331533 (3--08)

FaST SYSTEM (OPTION)

FaST SYSTEM MAINTENANCE

Every 1000 hours replace the water filter and airfilter located in the FaST detergent injector. Orderfilter kit p/n 9003009.

To access the detergent injector assembly, lowerthe scrub head and remove the front cover.

Remove the injector assembly from clamps.

Replace the water and air filter. An 8mm hexwrench required to install new water filter. Water Filter

(50 Mesh/Brown)

Air Filter(50 Mesh/Brown)

MAINTENANCE

5700XP 331533 (3--08)76

FaST SYSTEM FILTER SCREEN

The FaST system filter screen is located underthe solution tank and filters the water from thesolution tank as it flows into the FaST system.

Remove the filter screen bowl and clean the filterscreen after every 50 hours of machine operation.Empty the solution tank before removing the filter.

FaST SUPPLY HOSE CONNECTOR

The FaST supply hose connector is located belowthe FaST PAK holder. Soak the connector inwarm water if detergent buildup is visible. When aFaST PAK carton is not installed, store the supplyhose connector on the storing plug to prevent thehose from clogging.

MAINTENANCE

775700XP 331533 (10--08)


ec-H2O MODULE FLUSH PROCEDURE

This procedure is only required when an alarmsounds and the ec--H2O system indicator lightbegins to blink red.

1. Drain the solution tank and recovery tank ofall water.

2. Pour 2 gallons (8 liters) of white or ricevinegar into the solution tank at full strength.Do not dilute.

NOTE: Use white or rice vinegar only. Theacidity level should be between 4--8%. Do not useother acids for this procedure.

FOR SAFETY: When servicing machine, wearprotective gloves and eye protection whenhandling vinegar.

3. Disconnect the black connector fitting at thescrub head and place the hose into abucket. To access the connector fitting, youmay have to remove the front cover from themachine.

4. Turn the key to the on ( I ) position.

5. Press and release the ec--H2O module flushswitch to start the flush cycle. The module islocated behind the front cover.

NOTE: The module will automatically shut offwhen the flush cycle is complete (approx. 7minutes). The module must run the full 7 minutecycle in order to reset the system indicator lightand alarm.

Repeat flush procedure if the ec--H2Omodule does not reset. If module fails toreset, contact an Authorized Service Center.

MAINTENANCE

5700XP 331533 (9--06)78

SQUEEGEE

The squeegee assembly channels water into thevacuum fan suction. The front blade channels thewater, and the rear blade wipes the floor.

Check the squeegee blades for damage and weardaily. Rotate or replace either of the squeegeeblades if the leading edge is torn or worn half-waythrough the thickness of the blade.

The squeegee can be adjusted for leveling anddeflection. The deflection and leveling of thesqueegee blades should be checked daily, orwhen scrubbing a different type of floor.

The squeegee assembly can be removed fromthe squeegee pivot to prevent damage duringtransport of the machine, or when changing to adifferent squeegee width. The squeegees areavailable in three widths to be used with the threedifferent model scrub heads; model 700 (700 mm(28 in)), model 800 (800 mm (32 in)), and model900 (900 mm (36 in)).

REMOVING THE SQUEEGEE ASSEMBLY

6. Raise the squeegee.



8. Remove the squeegee suction hose fromthe squeegee.

MAINTENANCE

795700XP 331533 (9--06)

9. Loosen the two mounting knobs.

10.Pull the squeegee off the machine.

INSTALLING THE SQUEEGEE ASSEMBLY

1. Make sure the squeegee is raised.

2. Place the squeegee under the squeegeepivot.

3. Slide the squeegee frame onto thesqueegee pivot.

4. Tighten the mounting knobs.

5. Push the squeegee suction hose on thesqueegee.

LEVELING THE SQUEEGEE

Leveling of the squeegee assures even contactthe length of the squeegee blade with the surfacebeing scrubbed. Make sure this adjustment isdone on an even, level floor.


2. Lower the squeegee.

3. Drive the machine forward, then turn themachine power off.

4. Look at the deflection of the squeegeeblade, over the full length of the squeegeeblade.

MAINTENANCE

5700XP 331533 (9--06)80

5. If the deflection is not the same over the fulllength of the blade, turn the squeegeeleveling knob counter-clockwise to increasethe deflection at the ends of the squeegee.

Turn the squeegee leveling knob clockwiseto decrease the deflection at the ends of thesqueegee blade.

6. Drive the machine forward again with thesqueegee down to check the squeegeeblade deflection.

7. Readjust the squeegee blade deflection ifnecessary.

ADJUSTING SQUEEGEE BLADE DEFLECTION

Deflection is the amount of curl the squeegeeblade has when the machine moves forward withthe squeegee lowered to the floor. The bestdeflection is when the squeegee wipes the floorjust dry with a minimum amount of deflection.


2. Lower the squeegee.

3. Drive the machine forward, and look at thedeflection of the squeegee blade. Thecorrect amount of deflection is 12 mm(0.50 in) for scrubbing smooth floors and15 mm (0.62 in) for rough floors.


5. To adjust the amount of deflection, turn thesqueegee deflection cams counter-clockwiseto decrease the blade deflection.

Turn the squeegee deflection camsclockwise to increase blade deflection.

6. Drive the machine forward again to checkthe squeegee blade deflection.

7. Readjust the squeegee blade deflection ifnecessary.

03719

12 mm(0.50 in)

MAINTENANCE

815700XP 331533 (9--06)

ADJUSTING THE SQUEEGEE GUIDEROLLERS

At each end of the squeegee are guide rollers toguide the squeegee blade end along a wall.Loosen the nut at the top of the guide roller andmove the roller in or out to adjust how close theend of the squeegee blade comes to the wall. Thesqueegee blade end should be further away fromthe wall when the floor curves up into the wall.

SQUEEGEE BLADES

The squeegee has two squeegee blades, the frontand back. Each blade has four wiping edges. Touse them all, start with one wiping edge. To usethe next wiping edge, rotate the bladeend-for-end. To use the next wiping edge, rotatethe top edges down, bottom edges up. To use thelast edge, rotate the blade end-for-end.

Replace any worn or damaged squeegee blades.

REPLACING OR ROTATING THE REARSQUEEGEE BLADE

1. Make sure the squeegee is raised off thefloor.



3. Loosen the two retention knobs, one at eachend on the squeegee.

MAINTENANCE

5700XP 331533 (9--06)82

4. Pull off the rear retaining band.

5. Pull off the rear squeegee blade.

6. Insert the rotated or new squeegee bladeand then insert the retainer band.

7. Tighten the two retention knobs until theends of the front and rear squeegee bladestouch. Do not overtighten.

REPLACING OR ROTATING THE FRONTSQUEEGEE BLADE

1. Make sure the squeegee is raised off thefloor.



3. Remove the squeegee from the machine.See REMOVING THE SQUEEGEEASSEMBLY.

4. Remove the rear squeegee blade andretainer. See REPLACING OR ROTATINGTHE REAR SQUEEGEE BLADE.

MAINTENANCE

835700XP 331533 (9--06)

5. Loosen the two remaining knobs on top ofthe squeegee assembly.

6. Pull the retainer plate back and pull out thefront squeegee blade of the squeegeeframe.

7. Insert the rotated or new squeegee blade inthe squeegee frame, lining up the slots inthe blade with the tabs on the retainer plate.

8. Push the retainer plate forward. Tighten thetwo outside knobs on top of the squeegeeassembly.

9. Insert the rear squeegee blade and retainer.Tighten the two rear blade retention knobsuntil the ends of the front and rear squeegeeblades touch. Do not overtighten.

10. Install the squeegee assembly on thesqueegee pivot. See INSTALLING THESQUEEGEE ASSEMBLY.

11. Adjust the squeegee blade leveling anddeflection as stated in LEVELING THESQUEEGEE and ADJUSTING SQUEEGEEBLADE DEFLECTION.

MAINTENANCE

5700XP 331533 (9--06)84

BELTS AND CHAINS

BRUSH DRIVE BELT

The two brush drive belts are located on thecylindrical brush scrub head. The belts drive thecylindrical brushes. Proper new belt tension is a 3mm (0.1 in) deflection from a force of 1.37 to 1.48kg (3.0 to 3.26 lb) at the belt midpoint.

When reusing an old belt, measure and record thebelt tension before removal, so that the belt canbe reinstalled at the same tension.

If the old belt tension was not recorded, therecommended force per old belts is1.03 to 1.14 kg (2.28 to 2.52 lb) with a deflectionof 3 mm (0.1 in).

Check the belt tension and wear every 100 hoursof operation.

STATIC DRAG CHAIN

A static drag chain prevents the buildup of staticelectricity in the machine. The chain is attached tothe transaxle.

Make sure the chain is always touching the floor.

MAINTENANCE

855700XP 331533 (9--06)

TIRES

The standard front tires are pneumatic.

Check the front tire pressure every 50 hours ofoperation. The proper tire air pressure is415 to 450 kPa (60 to 65 psi).

The front wheel lug nuts should be tightened to102 to 115 Nm (75 to 85 ft lb).

PUSHING AND TRANSPORTING THEMACHINE

PUSHING THE MACHINE

If the machine becomes disabled, it can bepushed if necessary.

Unplug the drive motor from the electrical harnessbefore attempting to push a disabled machine.The machine will become easier to maneuverwhen it is unplugged.

ATTENTION! Do not push the machinefor a long distance and withoutunplugging the drive motor or damagemay occur to the propelling system.

Only push a disabled machine for a very shortdistance and do not exceed 3.2 kp/h (2 mph). It isNOT intended to be pushed for a long distance orat a high speed.

MAINTENANCE

5700XP 331533 (9--06)86

TRANSPORTING THE MACHINE

1. Position the rear of the machine at theloading edge of the truck or trailer.

FOR SAFETY: Use truck or trailer thatwill support the weight of the machine.

NOTE: Empty the recovery and solution tanksbefore transporting the machine.

2. If the loading surface is not horizontal or ishigher than 380 mm (15 in) from the ground,use a winch to load machine.

If the loading surface is horizontal AND is380 mm (15 in) or less from the ground, themachine may be pushed onto the truck ortrailer.

3. To winch the machine onto the truck ortrailer, attach the winching chains to the reartie down locations on either side of themachine frame by the rear casters.

4. Unplug the drive motor from the electricalharness before attempting to winch themachine. The machine will become easier tomaneuver when it is unplugged.

FOR SAFETY: When loading machineonto truck or trailer, use winch. Do notpush the machine onto the truck ortrailer unless the loading surface ishorizontal AND is 380 mm (15 in) or lessfrom the ground.

5. Position the machine onto the truck or traileras far as possible. If the machine starts toveer off the centerline of the truck or trailer,stop and straighten the machine.

MAINTENANCE

875700XP 331533 (9--06)

6. Lower the scrub head with the brushesinstalled, lower the squeegee, and set themachine parking brake, if equipped whentransporting the machine. Block the machinetires and tie down the machine to the truckor trailer before transporting.

NOTE: Do not use the steering handles tosecure the machine for transport.

Secure a strap over the top of the machineto prevent the machine from tipping.

The rear tie-down locations are on eitherside of the machine frame by the rearcasters.

7. If the loading surface is not horizontal or ishigher than 380 mm (15 in) from the ground,use a winch to unload machine.

If the loading surface is horizontal AND is380 mm (15 in) or less from the ground, themachine may be pushed off the truck ortrailer.

FOR SAFETY: When unloading machineoff truck or trailer, use winch. Do notpush the machine off the truck or trailerunless the loading surface is horizontalAND 380 mm (15 in) or less from theground.

MAINTENANCE

5700XP 331533 (10--08)88

MACHINE JACKING

Empty the recovery and solution tanks beforejacking the machine. You can jack up the machinefor service anywhere under the recovery tank.Use a hoist or jack that will support the weight ofthe machine. Use a piece of wood to distribute themachine weight load.

Always stop the machine on a flat level surfaceand block the machine tires before jacking up themachine.

FOR SAFETY: When servicing machine,block machine tires before jackingmachine up.

FOR SAFETY: When servicing machine,jack machine up at designated locationsonly. Block machine up with jackstands.

STORAGE INFORMATION

The following steps should be taken when storingthe machine for extended periods of time.

1. Drain and clean the solution and recoverytanks.

2. Park the machine in a cool, dry area.

3. Remove the batteries, or charge them afterevery three months.

FREEZE PROTECTION

1. Drain the solution tank and recovery tank ofall water.

2. Pour 2 gallons (8 liters) of recreationalvehicle (RV) antifreeze into the solution tankat full strength. Do not dilute.

FOR SAFETY: Avoid eye contact withantifreeze. Wear safety glasses.

3. Turn the machine power on and operate thesolution flow system. Turn the machine offwhen the red RV antifreeze is visible.

If your machine is equipped with theoff--aisle wand option, operate the off--aislewand for a few seconds to protect the pump.

Continue with the freeze protection procedure ifmachine is equipped with the ec--H2O system.

MAINTENANCE

895700XP 331533 (10--08)

ec-H2O Model:

4. Press and release the flush switch on theec--H2O module to cycle the antifreezethrough ec--H2O system.When theantifreeze is visible, press the switch againto turn off the module. The module is locatedbehind the front cover.

IMPORTANT: Before operating machine, theantifreeze must be flushed from the module asdescribed below.

If the antifreeze is not properly flushed from theec--H2O system, the ec--H2O module may detectan error and not function (ec--H2O switchindicator light will turn red). If this occurs, resetkey and repeat the flush procedure as describedbelow.

Flushing antifreeze from ec-H2O module:

1. Drain the antifreeze from the solution tankinto a bucket.

2. Fill the solution tank with cool water until full(See FILLING SOLUTION TANK).

3 Disconnect the black connector fitting at thescrub head and place the hose into abucket. To access the connector fitting, youmay have to remove the front cover from themachine.

4. Press and release the ec--H2O module flushswitch to start the flush cycle. The module islocated behind the front cover.

When the water turns clear, press themodule switch again to stop the flush cycle.

Dispose the antifreeze in an environmentally safeway according to local waste disposal regulations.

5. The machine is now ready for scrubbing.

SPECIFICATIONS

5700XP 331533 (9--06)90

SPECIFICATIONS

GENERAL MACHINE DIMENSIONS/CAPACITIES

Item Dimension/capacity

Length with cylindrical scrub head 1600 mm (63 in)

Length with 700 mm (28 in) disk scrub head 1625 mm (64 in)

Length with 800 mm (32 in) disk scrub head 1660 mm (65.25 in)

Length with 900 mm (36 in) disk scrub head 1690 mm (66.5 in)

Width (less squeegee and scrub head) 720 mm (28.25 in)

Height 1090 mm (43 in)

Disk brush diameter for 700 mm (28 in) scrubhead

355 mm (14 in)


405 mm (16 in)


455 mm (18 in)

Cylindrical brush diameter 150 mm (6 in)

Cylindrical brush length for 700 mm (28 in) scrubhead

700 mm (28.00 in)


800 mm (32.00 in)


900 mm (36.00 in)

Squeegee width for 700 mm (28 in) scrub head 950 mm (37.5 in)

Squeegee width for 800 mm (32 in) scrub head 1070 mm (42 in)

Squeegee width for 900 mm (36 in) scrub head 1160 mm (45.5 in)

Scrubbing path width for 700 mm (28 in) scrubhead

700 mm (28 in)


800 mm (32 in)


900 mm (36 in)

Solution tank capacity (recommended usage) 114 L (30 gal)

Solution tank capacity (maximum) 133 L (35 gal)

Recovery tank capacity to full sensor 114 L (30 gal)

Recovery tank capacity to top of tank 152 L (40 gal)

Transaxle 90 weight gear lubricant capacity 1.42 L (1.5 qt)

GVWR 690 kg (1520 lb)

SPECIFICATIONS

915700XP 331533 (10--08)

FaST SYSTEM (OPTION)

Item Measure

Solution pump 36 Volt DC, 5A, 5.7 LPM (1.5 GPM) open flow,45 psi bypass setting

Solution flow rate 0.83 LPM (0.22 GPM)

Detergent pump 36 Volt DC

Concentrate flow rate 0.9 CC/Minute (0.03 Ounces/Minute)

Concentrate to water dilution ratio 1:1000


Item Measure

Solution pump 36 Volt DC, 5A, 5.7 LPM (1.5 GPM) open flow,45 psi bypass setting

Solution flow rate* -- Disk 700 mm (28 in) 0.22 gpm / 0.83 L/min (standard)

0.33 gpm / 1.25 L/min (optional)








Solution flow rate* -- Cylindrical 700 mm (28 in) 0.33 gpm / 1.25 L/min (standard)





0.53 gpm / 2.00 LPM (optional)

* If the optional solution flow rates are required, contact an Authorized Service Center.

GENERAL MACHINE PERFORMANCE

Item Measure

Aisle turnaround width with 700 mm (28 in) scrubhead

1680 mm (66.25 in)


1700 mm (67 in)


1725 mm (67.5 in)

Maximum rated climb and descent angle withempty tanks

8_

Maximum rated climb and descent angle with fulltanks

6_

SPECIFICATIONS

5700XP 331533 (9--06)92

POWER TYPE

Type Quantity Volts Ah Rating Weight

Batteries 6 6 235 @ 20 hr rate 30 kg (67 lb)

6 6 335 @ 20 hr rate 47 kg (104 lb)

Type Use VDC Kw (hp)

Electric Motors Scrub brush (disk) 36 0.45 (0.60)

Heavy duty scrub brush (disk) 36 0.75 (1)

Scrub brush (cylindrical) 36 0.56 (0.75)

Vacuum fan 36 0.63 (0.85)

Propelling 36 0.37 (0.50)

Type VDC amp Hz Phase VAC

Chargers (Smart) 36 20 60 1 115

36 30 60 1 115

Chargers(International)

36 20 50 1 230

36 20 50 1 245

36 30 50 1 230

36 30 50 1 245

TIRES

Location Type Size Pressure

Front (2) Pneumatic 4.10/3.5 -- 6 415 to 450 kPa (60 to 65 psi)

Front (2) Solid (option) 1.2/3.0--6 --

Rear, casters (2) Solid, non-marking 5 x 2 in --

SPECIFICATIONS

935700XP 331533 (9--06)

1600 mm (63 in)1625 mm (64 in)

1660 mm (65.25 in)1690 mm (66.5 in)

950 mm (37.5 in)1065 mm (42 in)1155 mm (45.5 in)

720 mm (28.25 in)1090 mm (43 in)

10189

MACHINE DIMENSIONS

(Electric) (10000000-- ) Walk--Behind Scrubber Operator Manual 5700XP User Manual.pdf · 5700XP...

Documents

Transcript of (Electric) (10000000-- ) Walk--Behind Scrubber Operator Manual 5700XP User Manual.pdf · 5700XP...