Elecs - 5) Power Supply
-
Upload
arjay-salgado -
Category
Documents
-
view
282 -
download
2
Transcript of Elecs - 5) Power Supply
![Page 1: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/1.jpg)
POWER SUPPLY CIRCUIT
![Page 2: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/2.jpg)
Block Diagram Of A Complete Power Supply
![Page 3: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/3.jpg)
Transformer Types
• Core Type • Shell Type
![Page 4: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/4.jpg)
Typical Power Transformers
• Shell Method - provides maximum coupling between windings
- creates considerable interwinding capacitance - can not handle very much voltage
• Core Method - the coupling occurs by means of magnetic flux in the core - the interwinding capacitance is lower - can handle higher voltages
![Page 5: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/5.jpg)
Parts Of A Transformer
• Core – provides a path for the magnetic lines of flux• Primary Winding – receives the energy from the AC
source• Secondary Winding – receives the energy from the
primary winding and delivers it to the load• Enclosure – protects the above components from dirt,
moisture and mechanical damage
![Page 6: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/6.jpg)
Main Functions Of A Transformer
• Stepping up of Voltage• Stepping down of Voltage• Provides isolation between primary and secondary
windings• Impedance Matching
![Page 7: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/7.jpg)
Transformer Formulas
• Turns Ratio, a : a = Ns/Np
• Voltage Ratio : Es/Ep = Ns/Np
• Current Ratio : Is/Ip = Np/Ns
• Impedance Ratio : Ns/Np = √Zs/Zp
• Transformers are rated according to the output voltage and current (VA capacity)
![Page 8: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/8.jpg)
Transformer LossesCopper Loss or I²R loss – it is the losses due to the primary
and secondary windings of the transformer
Core Loss or Iron Loss
1. Eddy Current Loss – due to the changing magnetic field and the iron core conductivity. This current is produced in the iron core that does not aid transformer output. It can be minimized through laminating the core
2. Hysteresis Loss – since AC currents constantly change in magnitude and direction, the tiny molecular agents within the core are constantly being arranged and this process requires energy that causes some loss
![Page 9: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/9.jpg)
Transformer Efficiency, ɳ
ɳ = Po/Pi x 100% , where
ɳ is the efficiency of the transformer
Po is the power output drawn by the load,
Po = Vʟ Iʟ (P.F.)
Pi is the power developed by the transformer itself
Pi = Po + Pʟosses
![Page 10: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/10.jpg)
Rectifier
• An electronic circuit that converts AC voltage into pulsating DC
• It converts a signal having zero average value into one that has a nonzero average value
![Page 11: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/11.jpg)
Rectifier Circuits
• Half-Wave Rectifier – the simplest rectifier circuit which uses only one diode
• Full-Wave Rectifier – most commonly used in DC power supplies and can either be : a. Center-tap b. Bridge type
![Page 12: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/12.jpg)
Half-Wave Rectifier Circuits
![Page 13: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/13.jpg)
Half-Wave Rectifier
• Advantages 1.cost less because circuit is less complicated 2.adequate only for power supplies not required to deliver much current
• Disadvantages 1. the output is difficult to filter 2. the output voltage can drop considerably when the supply is required to deliver high current 3. HW rectification puts a strain on the transformer and the diode
![Page 14: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/14.jpg)
Bridge Type Rectifier
![Page 15: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/15.jpg)
Positive And Negative Half Cycles
• Positive Half Cycle • Negative Half Cycle
![Page 16: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/16.jpg)
Bridge Type Rectifier
• Advantages 1. the output voltage is easier to filter as compared to half-wave rectifiers 2. there are less ripple voltages 3. more efficient use of diodes
• Disadvantages 1. more complicated circuitry 2. more expensive
![Page 17: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/17.jpg)
Formulas
• Average Value of Half-Wave Rectified Voltage Vdc=Vp/π = 0.318 Vp
• Effective Value of a Half-Wave Rectified Voltage Vrms=Vp/2=0.5Vp
• Average Value of a FW Rectified Signal Vdc=2Vp/π=0.636Vp
• Effective Value of a FW Rectified Signal Vrms=Vp/√2
![Page 18: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/18.jpg)
Ripple Factor
• The pulsating dc output of a rectifier contains ripple voltages
• The amount of ripple can be measured by means of a ripple factor which is defined as r = ripple voltage in AC rms voltage / DC voltage
r = AC voltage / DC voltage
r = ripple voltage in rms / average dc voltage
= Vr (rms) / Vdc • The ripple factor is an indication of the effectiveness of a
filter, wherein, for a power supply, the lesser the value of the ripple, the better is the performance
![Page 19: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/19.jpg)
Ripple Factor of Rectified Voltages
Half Wave Rectifier
Vr (rms) = 0.385Vm
r=Vr (rms)/Vdc x 100%
r=0.385Vm/0.318Vm x 100%
r = 121%
Full Wave Rectifier
Vr(rms) = 0.308Vm
r = Vr(rms)/Vdc x 100%
r = 0.308Vm/0.636Vm x 100%
r = 48%
![Page 20: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/20.jpg)
![Page 21: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/21.jpg)
Power Supply Filter
• The output of a rectifier is a pulsating dc and is not yet suitable for most dc powered devices
• These pulsations are known as ripple voltages • Ripples can be eliminated by means of filters• A filter circuit is necessary to provide a steadier dc
voltage; it is used to keep the ripple component from appearing in the output
• Filters are implemented with capacitors• When the rectified signal undergoes filtering, the output is
nearly smooth dc voltage• The small fluctuations in the filter output is called the ripple
![Page 22: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/22.jpg)
Effects of Filter
How effective is a filter?
• The effectiveness of a filter is measured by the ripple factor. Generally, the ripple is undesirable, thus, the smaller the ripple, the better is the filtering action
How can a filter be made more efficient?
• The lower the ripple, the better the filter. Ripple factor can be lowered by increasing the value of the filter capacitor or increasing the load resistance
![Page 23: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/23.jpg)
Two Basic Types of Filters
1. Capacitance Filters (C-filter)
2. RC filter
![Page 24: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/24.jpg)
Capacitor Filter
• The simplest and most economical filter• A capacitor is connected across the output of a rectifier
and a dc output voltage is obtained across the capacitor• When the diode is forward biased, the capacitor charges
and when the diode is reverse biased, the capacitor discharges
• Ripple voltages is caused by the charging and discharging of the filter capacitor
![Page 25: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/25.jpg)
The C-filter Equations
Vr (rms) = Idc / 4√3fC
Vdc = Vm – Vm/ T/4
%r = Vr (rms) / Vdc x 100%
With f=60 Hz, Idc in mA, C in μF and Rʟ in kΩ
Vr (rms) = 2.4 Idc / C = 2.4 Vdc / Rʟ C
Vdc = Vm – 4.16 Idc / C
% r = 2.4 Idc / C Vdc x 100%
% r = 2.4 / C Rʟ x 100%
![Page 26: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/26.jpg)
RC Filters
• The ripple of the filtered voltage can be reduced by connecting an additional RC filter section
• The purpose of the added RC section is to pass most of the dc component and attenuate the ac component as much as possible
![Page 27: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/27.jpg)
Full Wave C - Filter circuit
![Page 28: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/28.jpg)
FW Capacitor Filter
The simple capacitor filter shown in figure 3-20 consists of a single-filter element.
This capacitor (C1) is connected across the output of the rectifier in parallel with the load.
The RC charge time of the filter capacitor (C1) must be short and the RC discharge time must be long to eliminate ripple action when using this filter.
In other words, the capacitor must charge up fast with preferably no discharge at all.
Better filtering also results when the frequency is high; therefore, the full-wave rectifier output is easier to filter than the half-wave rectifier because of its higher frequency.
![Page 29: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/29.jpg)
Full Wave Rectifier W/ and W/o Capacitor Filters
![Page 30: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/30.jpg)
RC Filters
• The ripple of the filtered voltage can be reduced by connecting an additional RC filter section
• The purpose of the added RC section is to pass most of the dc component and attenuate the ac component as much as possible
![Page 31: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/31.jpg)
Low Pass Filter
By definition, a low-pass filter is a circuit offering easy passage to low-frequency signals and difficult passage to high-frequency signals.
There are two basic kinds of circuits capable of accomplishing this objective, and many variations of each one: The inductive low-pass filter and the capacitive low-pass filter.
![Page 32: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/32.jpg)
Low Pass Filters
![Page 33: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/33.jpg)
Inductive vs. Capacitive
Inductive low-pass filter
The inductor's impedance increases with increasing frequency. This high impedance in series tends to block high-frequency signals from getting to the load.
Capacitive low-pass filter.
The capacitor's impedance decreases with increasing frequency. This low impedance in parallel with the load resistance tends to short out high-frequency signals, dropping most of the voltage across series resistor R1.
![Page 34: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/34.jpg)
High Pass Filter
A high-pass filter's task is just the opposite of a low-pass filter:
to offer easy passage of a high-frequency signal and difficult passage to a low-frequency signal.
As one might expect, the inductive and capacitive versions of the high-pass filter are just the opposite of their respective low-pass filter designs.
![Page 35: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/35.jpg)
High Pass Filter
![Page 36: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/36.jpg)
Inductive vs. Capacitive
Inductive high-pass filter.The inductor's impedance
decreases with decreasing frequency.
This low impedance in parallel tends to short out low-frequency signals from getting to the load resistor.
As a consequence, most of the voltage gets dropped across series resistor R1.
Capacitive high-pass filter.
The capacitor's impedance increases with decreasing frequency. This high impedance in series tends to block low-frequency signals from getting to load.
![Page 37: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/37.jpg)
Applications of HP and LP Filters
![Page 38: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/38.jpg)
RC Filters
![Page 39: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/39.jpg)
Voltage Regulators
• A voltage regulator is an electronic circuit that provides a constant dc output voltage that is essentially independent of the input voltage, output load current and temperature
• Voltage regulators fall under two categories, the linear regulators and the switching regulators
• Voltage regulators can be connected from discrete transistors and other components, but most regulators are now available in IC types
• The input to a regulator comes from a filtered output of a rectifier
![Page 40: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/40.jpg)
Sample PCB Design
![Page 41: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/41.jpg)
Zener Diode Regulator
![Page 42: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/42.jpg)
What is Regulation?
• Regulation that is expressed in percentage is a figure of merit used to specify the performance of a voltage regulator. It can be expressed in terms of input (line) regulation or load regulation
• Line regulation specifies how much change occurs in the output voltage for a given change in the input voltage. It is defined mathematically as,
LR= ∆Vout/∆Vin x 100%• Load Regulation specifies how much change occurs in
the output voltage from the no-load to full-load condition
LR=Vɴʟ-Vғʟ / Vғʟ x 100%
![Page 43: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/43.jpg)
How Regulated is a Regulator?
• The operation of a regulator can be evaluated using percent regulation
• The smaller the percentage, the better is the performance of the power supply
• An ideal power supply has a regulation of 0%, meaning, there is no change in the output voltage even the line voltage or the line current drawn by the load changes
![Page 44: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/44.jpg)
Basic Series Regulator
![Page 45: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/45.jpg)
Basic Series Regulator Circuit
• The series element controls the amount of input voltage that goes to the output
• The zener-follower is the simplest series voltage regulator
• Op-amps can be used to achieve better regulation• Any attempted change in the output voltage is offset by
the negative feedback
![Page 46: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/46.jpg)
Basic Series Regulator Circuit
![Page 47: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/47.jpg)
Basic Shunt Regulator
• The control element which is usually a transistor is in parallel with the load
• The simplest form is the zener diode circuit• Improved regulation can be achieved by using two
transistors or employing an op amp with negative feedback
![Page 48: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/48.jpg)
Basic Shunt Regulator Diagram
![Page 49: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/49.jpg)
Series vs. Shunt
Shunt Regulator
• Has built-in short circuit protection
• Has low efficiency• When efficiency is not
important, shunt regulators are used because of advantage of simplicity
Series Regulator
• More efficient for most applications
• Requires current limiting because it has no short circuit protection
• When larger load currents are needed, efficiency becomes more important and the series regulator is preferred
![Page 50: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/50.jpg)
Short Circuit Protection and Foldback Current Limiting
Short Circuit Protection• The pass transistor of a series
regulator as well as the rectifier diodes can be damaged if the load terminals have been shorted or an excessive amount of load current is drawn
• To protect against accidental short across the load, series regulators employ some form of current limiting
• Current limiting reduces the load voltage when the current becomes larger than the limiting value
Foldback Current Limiting• Reduces both the output voltage
and the output current, protecting the load from overcurrent as well as protecting the regulator
• In effect, there is a reduced power dissipation in the pass transistor when the load terminals are shorted
![Page 51: Elecs - 5) Power Supply](https://reader033.fdocuments.us/reader033/viewer/2022061105/543f0597b1af9f780b8b4d2f/html5/thumbnails/51.jpg)
Assignment
Research on :1. Switching Regulators
- Operation & Circuit
- Topologies
2. IC Voltage Regulators
- Fixed Positive Voltage Regulators
- Fixed Negative Voltage Regulators
- Adjustable Voltage Regulators
3. Comparison between Linear (series & shunt) vs. Switching regulators in terms of efficiency, noise and design